Whirlpool SPIW309A3WF.1 Manuale utente

Categoria
Condizionatori d'aria a sistema split
Tipo
Manuale utente
Instructions for use
Gebrauchsanweisung
Directives d’utilisation
Gebruiksaanwijzing
Instrucciones de uso
Instrucciones de uso
Libretto di istruzioni
Οδηγίε χρήση
Bruksanvisning
Bruksanvisning
Brugsanvisninger
Käyttöohjeet
Instrukcja użytkownika
Návod k obsluze
Návod na používanie
Használati útmutató
  
  
Instruciuni de utilizare
  
- 3 -
ENGLISH Instructions for use Page 4
DEUTSCH Bedienungsanleitung Seite 20
FRANÇAIS Consignes d’utilisation Page 36
NEDERLANDS Gebruiksaanwijzing Pagina 52
ESPAÑOL Instrucciones de uso Página 68
PORTUGUÊS Instruções de utilização Página 84
ITALIANO Istruzioni per l’uso Pagina 100
ΕΛΛΗΝΙΚΑ Οδηγίες χρήσης Σελίδα 116
SVENSKA Bruksanvisning Sidan 132
NORSK Brukerveiledning Side 148
DANSK Brugsanvisninger Side 164
SUOMI Käyttöohje Sivu180
POLSKI Instrukcja użytkownika Strona 196
ČESKY Návod kobsluze Strana 212
SLOVENSKÝ Návod na používanie Strana 228
MAGYAR Használati útmutató 244. oldal
 Инструкция по эксплуатации Стр. 260
 Инструкции за използване Страница 276
ROMÂNĂ Instrucţiuni de utilizare Pagina 292
 Інструкції з використання стор.308
SPIW309A3WF.1
SPIW312A3WF.1
SPIW309A2WF
SPIW312A2WF
SPIW318A2WF
SPIW309L
SPIW312L
SPIW318L
- 4 -
IMPORTANT TO BE READ AND OBSERVED
Download the complete instruction manual on docs.whirlpool.eu or call the phone
number shown on the warranty booklet.
Before using the appliance, read these safety instructions. Keep them nearby for future
reference.
These instructions and the appliance itself provide important safety warnings, to be
observed at all times. The manufacturer declines any liability for failure to observe these
safety instructions, for inappropriate use of the appliance or incorrect setting of controls.
Very young children (0-3 years) should be kept away from the appliance. Young
children (3-8 years) should be kept away from the appliance unless continuously
supervised. Children from 8 years old and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge can use this
appliance only if they are supervised or have been given instructions on safe use and
understand the hazards involved. Children must not play with the appliance. Cleaning
and user maintenance must not be carried out by children without supervision.
PERMITTED USE
CAUTION: the appliance is not intended to be operated by means of an external
switching device, such as a timer, or separate remote controlled system.
This appliance is intended to be used in household and similar applications such as:
hotels and working oces.
This appliance is not for professional use.
Always turn o the air conditioner by remote control rst. Do not use the power supply
circuit breaker or pull o the plug to turn it o. Disconnect the air conditioner from the
power supply if it is to be left unused for a long period of time or during a thunder/
lightning storm.
Never insert obstacle in the air outlet-risk of injury. Keep ventilation openings clear of any
obstruction.
Do not place any other electrical products or household belongings under indoor unit
or outdoor unit. Condensation dripping from the unit might get them wet, and may cause
damage or malfunction of your property.
INSTALLATION
The appliance must be handled and installed by two or more persons - risk of injury.
Use protective gloves to unpack and install - risk of cuts.
Installation, including electrical connections, and repairs must be carried out by a
qualied technician according to national wiring rules. Do not repair or replace any
part of the appliance unless specically stated in the user manual. Keep children away
from the installation site. After unpacking the appliance, make sure that it has not
been damaged during transport. In the event of problems, contact the dealer or your
nearest After-sales Service. Once installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children - risk of suocation. The appliance must be
disconnected from all remote power supply before any installation operation - risk of
electric shock. During installation, make sure the appliance does not damage the power
cable - risk of re or electric shock. Only activate the appliance when the installation has
been completed.
SAFETY INSTRUCTIONS
- 5 -
When moving or relocating the air conditioner, consult experienced service technicians
for disconnection and reinstallation of the unit.
The appliance shall not be installed in the laundry.
ELECTRICAL WARNINGS
The power supply must be of rated voltage with special circuitry for the appliance.
The diameter of the power cord must comply with requirements.
A multi-pole switch shall be installed in the xed wiring in accordance with the wiring
rules and the appliance must be earthed in conformity with national electrical safety
standards.
An all-pole disconnection switch having a contact separation of at least 3 mm in all poles
should be connected in xed wiring.
Do not use extension leads, multiple sockets or adapters. The electrical components
must not be accessible to the user after installation. Do not use the appliance when you are
wet or barefoot. Do not operate this appliance if it has a damaged power cable or plug, if it
is not working properly, or if it has been damaged or dropped.
If the supply cord is damaged, it must be replaced with an identical one by the
manufacturer, its service agent or similarly qualied persons in order to avoid a hazard - risk
of electrical shock.
A residual current device (RCD) having rated residual operation current not exceeding
30 mA shall be incorporated in xed wiring according to national law.
The temperature of refrigerant circuit will be high, please keep the interconnection cable
away from the copper tube.
Ensure safe grounding and a grounding wire connected with the special grounding
system of the building, installed by professionals. The appliance must be tted with
electrical leakage protection switch and an auxiliary circuit breaker with sucient capacity.
The circuit breaker must also have a magnetic and a thermal tripping function to ensure
protection in case of short-circuit and overload.
Model 9K & 12K 18K 24K
Required capacity of circuit breaker 16A 20A 25A
For the connection of power cord and cable connection between indoor and outdoor
units, please see the wiring diagram on the appliance.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched o and disconnected from the
power supply before performing any maintenance operation; never use steam cleaning
equipment - risk of electric shock.
Maintenance and repair requiring the assistance of other skilled personnel shall be
carried out under the supervision of the person competent in the use of ammable
refrigerants.
Servicing shall only be performed with equipment as recommended by the
manufacturer.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the
packaging must therefore be disposed of responsibly and in full compliance with local authority regulations
governing waste disposal.
SAFETY INSTRUCTIONS
- 6 -
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste
disposal regulations. For further information on the treatment, recovery and recycling of household electrical
appliances, contact your local authority, the collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and
Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent negative
consequences for the environment and human health.
The ( )symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection center for the recycling of electrical and electronic
equipment.
DECLARATIONS OF CONFORMITY
The complete text of the declaration of conformity is present at the following website:
docs.whirlpool.eu.
The radio equipment operates in the 2.4 GHz ISM frequency band, the maximum
radio-frequency power transmitted does not exceed 20 dBm (e.i.r.p.).
This product includes certain open source software developed by third parties. The open
source license usage statement is available at the following website: docs.whirlpool.eu.
This product contains Fluorinated Greenhouse Gases covered by the Kyoto Protocol,
the refrigerant gas being in a hermetically sealed system (R32, GWP 675). The maximum
refrigerant charge amount is 2.5 kg. Please refer to the rating label for detailed
information.
SAFETY INSTRUCTIONS FOR SERVICING APPLIANCE WITH SPESIFIC REFRIGERANT
Download the complete manual for detailed installation, servicing, maintenance and
reparing methods on docs.whirlpool.eu.
Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer.
The appliance shall be stored in a well-ventilated area where the room size corresponds
to the room area as specied for operation; without continuously operating ignition
sources (such as; open ames, an operating gas appliance or an operating electric heater).
Do not pierce or burn. Be aware that the refrigerants may not contain an odor.
Any person who is involved with working on or breaking into a refrigerant circuit should
hold a current valid certicate from an industry-accredited assessment authority, which
authorizes their competence to handle refrigerants safely in accordance with an industry
recognized assessment specication. Servicing shall only be performed as recommended
by the equipment manufacturer. Maintenance and repair requiring the assisstance of other
skilled personnel shall be carried out under the supervision of the person competent in
the use of ammable refrigerants. Appliance shall be installed, operated and stored in a
room with a oor area larger than 10 m2. The installation of pipe-work shall be kept to a
room with a oor area larger than 10 m2. The pipe-work shall be compliance with national
gas regulations. The maximum refrigerant charge amount is 2.5 kg. Mechanical connectors
used indoors shall comply with ISO 14903. When mechanical connectors are reused
indoors, sealing parts shall be renewed. When ared joints are reused indoors, the are part
shall be re fabricated. The installation of pipe-work shall be kept to a minimum. Mechanical
connections shall be accessible for maintenance purposes.
1. Transport of equipment containing ammable refrigerants shall be compliant with the
SAFETY INSTRUCTIONS
- 7 -
transport regulations.
2. Marking of equipment using signs shall be compliant with local regulations.
3. Disposal of equipment using ammable refrigerants shall be compliant with national
regulations.
4. The storage of equipment / appliances should be in accordance with the
manufacturers instructions.
5. Storage of packed (unsold) equipment Storage package protection should be
constructed such that mechanical damage to the equipment inside the package
will not cause a leak of the refrigerant charge. The maximum number of pieces of
equipment permitted to be stored together will be by local regulations.
6. Information on servicing.
6-1 Checks to the area
Prior to beginning work on system containing ammable refrigerants, safety checks are
necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating
system the following precautions shall be complied with prior to conducting work on
the system.
6-2 Work procedure
Work shall be undertaken under a controlled procedure so as to minimize the risk of
ammable gas or vapour being present while the work is being performed.
6-3 General work area
All maintenance sta and others working in the local area shall be instructed on the
nature of work being carried out. Work in coned spaces shall be avoided. The area
around the workspace shall be sectioned o. Ensure that the conditionswithin the area
have been made safe by control of ammable material.
6-4 Checking for presence of refrigerant
The area shall be checked with an appropriate refrigerant detector prior to and during
work, to ensure the technician is aware of prtentially ammable atmospheres. Ensure
that hte leak detection equipment being used is suitable for use with ammable
refrigerants, i.e. non-sparking adequately sealed or intrinsically safe.
6-5 Presence of re extinguisher
If any hot work is to be conducted on the refrigeration equipment or any associated
partsappropriate re extinguishing equipment shall be avalaible to hand. Have a dry
powder or CO2 re extinguisher adjacent to the charging area.
6-6 No ignition sources
No person carrying out work in relation to a refrigeration system which involves exposing
any pipe work that contains or has contained ammable refrigerant shall use any
sources of ignition in such a manner that it may lead to the risk of re or explosion.
All possible ignition sources, including cigarette smoking, should be kept suciently
far away from the site of installation, repairing, removing and disposal, during which
ammable refrigerant can possibly be released to the surrounding space. Prior to work
taking place, the area around the equipment is to be surveyed to make sure that there
are no ammable hazards or ignition risks. “No Smoking signs shall be displayed.
6-7 Ventilated area
Ensure that the area is in the open or that it is adequately ventilated before breaking into
the system or conducting any hot work. A degree of ventilation shall continue during
the period that the work is carried out. The ventilation should safely disperse any
SAFETY INSTRUCTIONS
- 8 -
released refrigerant and preferably expel it externally into the atmosphere.
6-8 Checks to the refrigeration equipment
Where electrical components are being changed, they shall be t for the purpose
and to the correct specication. At all times the manufacturer’s maintenance and
service guidelines shall be followed. If in doubt consult the manufacturers technical
department for assistance. The following checks shall be applied to installations using
ammable refrigerants:
- The charge size is in accordance with the room size within which the refrigerant
containing parts are installed;
- The ventilation machinery and outlets are operating adequately and are not obstructed;
- If an indirect refrigerating circuit is being used, the secondary circuit shall be checked
for the presence of refrigerant;
- Marking to the equipment continues to be visible and legible. Markings and signs that
are illegible shall be corrected;
- Refrigeration pipe or components are installed in a position where they are unlikely to
be exposed to any substance which may corrode refrigerant containing components,
unless the components are constructed of materials which are inherently resistant to
being corroded or are suitably protected against being so corroded.
6-9 Checks to electrical devices
Repair and maintenance to electrical components shall include initial safety checks and
component inspection procedures. If a fault exists that could compromise safety, then
no electrical supply shall be connected to the circuit until it is satisfactory dealt with. if
the fault cannot be corrected immediately but it is necessary to continue operation, an
adequate temporary solution shall be used. This shall be reported to the owner of the
equipment so all parts are advised. Initial safety checks shall include:
- That capacitors are discharged: this shall be done in a safe manner to avoid possibility of
sparking;
- That there no live electrical components and wiring are exposed while charging,
recovering or purging the system;
- That there is continuity of earth bonding.
7. Repairs to sealed components
During repairs to sealed components, all electrical supplies shall be disconnected from
the equipment being worked upon prior to any removal of sealed electrical supply
to equipment during servicing, then a permanently operating form of leak detection
shall be located at the most critical point to warn of a potentially hazardous situation.
Particular attention shall be paid to the following to ensure that by working on coelectrical
components. The casing is not altered in such a way that the level of protection is
aected. This shall include damage to cables, excessive number of connections, terminals
not made to original specication, damage to seals, incorrect tting of glands, etc.
Ensure that apparatus is mounted securely. Ensure that seals or sealing materials have
not degraded such that they no longer serve the purpose of preventing the ingress of
ammable atmospheres. Replacement parts shall be in accordance with the manufacturers
specications.
NOTE:
SAFETY INSTRUCTIONS
- 9 -
SAFETY INSTRUCTIONS
The use of silicon sealant may inhibit the eectiveness of some types of leak detection
equipment. Intrinsically safe components do not have to be isolated prior to working on
them.
8. Repair to intrinsically safe components
Do not apply any permanent inductive or capacitance loads to the circuit without
ensuring that this will not exceed the permissible voltage and current permitted for the
equipment in use. Intrinsically safe components are the only types that can be worked on
whilelive in the presence of a ammable atmosphere. The test apparatus shall be at the
correct rating. Replace components onlywith parts specied by the manufacturer. Other
parts may result in the ignition of refrigerant atmosphere from a leak.
9. Cabling
Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp
edges or any other adverse environmental eects.The check shall also take into account the
eects of aging or continual vibration from sources such as compressors or fans.
10.Detection of ammable refrigerants
Under no circumstances shall potential sources of ignition be used in the searching for or
detection of refrigerant leaks. A halide torch (or any other detector using a naked ame)
shall not be used.
11.Leak detection methods
The following leak detection methods are deemed acceptable for systems containing
ammable refrigerants:
- Electronic leak detectors shall be used to detect ammable refrigerants, but the
sensitivity may not be adequate, or may need re-calibration (Detection equipment shall
be calibrated in a refrigerant-free area.)
- Ensure that the detector is not a potential source of ignition and is suitable for the
refrigerant used.
- Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and
shall be calibrated to the refrigerant employed and the appropriate percentage of gas
(25% maximum) is conrmed.
- Leak detection uids are suitable for use with most refrigerants but the use of
detergents containing chlorine shall be avoided as the chlorine may react with the
refrigerant and corrode the copper pipe-work.
- If a leak is suspected, all naked ames shall be removed/ extinguished.
- If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall
be recovered from the system, or isolated (by means of shut o valves) in a part of the
system remote from the leak.
- Oxygen free nitrogen (OFN) shall then be purged through the system both before and
during the brazing process.
12.Removal and evacuation
- When breaking into the refrigerant circuit to make repairs - or for any other purpose
conventional procedures shall be used. However, it is important that best practice is
followed since ammability is a consideration.
The following procedure shall be adhered to:
- Remove refrigerant;
- Purge the circuit with inert gas;
- Evacuate;
- 10 -
SAFETY INSTRUCTIONS
- Purge again with inert gas;
- Open the circuit by cutting or brazing.
The refrigerant charge shall be recovered into the correct recovery cylinders.The system
shall be “ushed with OFN to render the unit safe. This process may need to be repeated
several times. Compressed air or oxygen shall not be used for this task. Flushing shall
be achieved by breaking to ll until the working pressure is achieved, then venting to
atmosphere, and nally pulling down to a vacuum. This process shall be repeated until no
refrigerant is within the system. When the nal charge is used, the system shall be vented
down to atmospheric pressure to enable work. This operation is absolutely vital if brazing
operations, on the pipe-work are to take place. Ensure that the outlet for the vacuum
pump is not close to any ignition sources and there is the vacuum in the system with OFN
and continuing ventilation available.
13.Charging procedures
In addition to conventional charging procedures, the following requirements shall be
followed:
- Ensure that contamination of dierent refrigerants does not occur when using charging
equipment.
- Hoses or lines shall be as short as possible to minimize the amount of refrigerant
contained in them.
- Cylinders shall be kept upright.
- Ensure that the refrigeration system is earthed prior to charging the system with
refrigerant.
- Label the system when charging is complete (if not already).
- Extreme care shall be taken not to overll the refrigeration system. Prior to recharging
the system it shall be pressure tested with OFN.
The system shall be leak tested on completion of charging but prior to commissioning.
A follow up leak test shall be carried out prior to leaving the site.
14.Decommissioning
Before carrying out this procedure, it is essential that the technician is completely familiar
with the equipment and all its detail. It is recommended good practice that all refrigerants
are recovered safely. Prior to the task being carried out, an oil and refrigerant sample shall
be taken in case analysis is required prior to re-use of reclaimed refrigerant. It is essential
that electrical power is available before the task is commenced.
a. Become familiar with the equipment and its operation.
b. Isolate system electrically.
c. Before attempting the procedure ensure that:
- Mechanical handling equipment is available, if required, for handling refrigerant cylinders;
- All personal protective equipment is available and being used correctly;
- The recovery process is supervised at all times by a competent person;
- Recovery equipment and cylinders conform to the appropriate standards.
d. Pump down refrigerant system, if possible.
e. If a vacuum is not possible, make a manifold so that refrigerant can be removed from
various parts of the system.
f. Make sure that cylinder is situated on the scales before recovery takes place.
g. Start the recovery machine and operate in accordance with manufacturer’s
instructions.
- 11 -
SAFETY INSTRUCTIONS
h. Do not overll cylinders. (No more than 80 % volume liquid charge).
i. Do not exceed the maximum working pressure of the cylinder, even temporarily.
j. When the cylinders have been lled correctly and the process completed, make sure
that the cylinders and the equipment are removed from site promptly and all isolation
valves on the equipment are closed o.
k. Recovered refrigerant shall not be charged into another refrigeration system unless it
has been cleaned and checked.
15.Labelling
Equipment shall be labelled stating that it has been de-commissioned and emptied
of refrigerant. The label shall be dated and signed. Ensure that there are labels on the
equipment stating the equipment contains ammable refrigerant.
16.Recovery
When removing refrigerant from a system, either for servicing or decommissioning, it is
recommended good practice that all refrigerants are removed safely. When transferring
refrigerant into cylinders, ensure that only appropriate refrigerant recovery cylinders
are employed. Ensure that the correct number of cylinders for holding the total system
charge is available. All cylinders to be used are designated for the recovered refrigerant
and labelled for that refrigerant (i.e. special cylinders for the recovery of refrigerant).
Cylinders shall be complete with pressure relief valve and associated shuto valves in
good working order. Empty recovery cylinders are evacuated and, if possible, cooled
before recovery occurs. The recovery equipment shall be in good working order with
a set of instructions concerning the equipment that is at hand and shall be suitable
for the recovery of ammable refrigerants. In addition, a set of calibrated weighing
scales shall be available and in good working order. Hoses shall be complete with leak-
free disconnect couplings and in good condition. Before using the recovery machine,
check that it is in satisfactory working order, has been properly maintained and that
any associated electrical components are sealed to prevent ignition in the event of a
refrigerant release. Consult manufacturer if in doubt. The recovered refrigerant shall be
returned to the refrigerant supplier in the correct recovery cylinder, and the relevant
Waste Transfer Note arranged. Do not mix refrigerants in recovery units and especially
not in cylinders. If compressors or compressor oils are to be removed, ensure that they
have been evacuated to an acceptable level to make certain that ammable refrigerant
does not remain within the lubricant. The evacuation process shall be carried out prior to
returning the compressor to the suppliers. Only electric heating to the compressor body
shall be employed to accelerate this process. When oil is drained from a system, it shall
be carried out safely. When moving or relocating the air conditioner, consult experienced
service technicians for disconnection and reinstallation of the unit. Do not place any
other electrical products or household belongings under indoor unit or outdoor unit.
Condensation dripping from the unit might get them wet, and may cause damage or
malfunction of your property. To keep ventilation openings clear of obstruction. The
appliance shall be stored in a well-ventilated area where the room size corresponds
to the room area as specied for operation. The appliance shall be stored in a room
without continuously operating open ames (for example an operating gas appliance)
and ignition sources (for example an operating electric heater). Reusable mechanical
connectors and ared joints are not allowed.
- 12 -
Product description
Indoor unit
The gures in this manual are based on the external view of a standard model.
Consequently, the shape may dier from that of the air conditioner you have selected.
Explanation of symbols displayed on the indoor unit or outdoor unit.
WARNING This symbol shows that this appliance uses a
ammable refrigerant is leaked and exposer to an
external ignition source, there is a risk of re.
CAUTION Yhis symbol shows that the operation manual should
be read carefully.
CAUTION This symbol shows that a service personnel should
be handling this equipment with reference to the
installation manual.
CAUTION This symbol shows that information is available such
as the operating manual or installation manual.
Front Panel
Air Intake
Display Panel
Emergency Panel
Air Outlet
Air Filter
Remote Controller
Air Intake
Air Outlet
Vertical
Adjustment Louver
Horizontal
Adjustment Louver
Drain Hose
Pipes and Power
Connection Cord
Note: Condensate water drainsat
COOLING or DRY operation.
Outdoor unit
- 13 -
User Interface
Temperature indicator (1)
Displays set temperature.
It shows “FC as a reminder to clean the lter.
Wi-Fi indicator (2)
It blinks fast (3 Hz) when it’s connecting to router or lose connection to router.
It blinks slowly (1.5 Hz) when its connected to router but not connected to cloud.
It turns to be solid when the Wi-Fi is fully connected.
It goes o when the Wi-Fi is deprovisioned or turn o.
6th Sence indicator (3)
It lights up when 6th sense is on.
It goes o when 6th sense ends.
Filter monitor indicator (4)
IIt ashes when the lter needs to be cleaned.
Filter monitor indicator ashes after 720 hours of usage as reminder to clean the lter.
After lter cleaning, press the lter reset button located on the indoor unit behind the front panel in order to
interrupt the ashing of the lter monitor indicator.
Humidity indicator (5)
It lights up when showing the humility level.
It goes o when showing the temperature.
Timer indicator (6)
It lights up during the set time.
It goes o when timer operation ends.
Running indicator (6)
It lights up during operation.
It ashes during outside unit defrosting.
Sleep indicator (8)
It lights up once sleep mode is set, “Running” indicator will ash for 10 times then the whole display will light
o.
For air conditioners without Wi-Fi control, we recommend the Wpro SmartClim: a smart device to control via Wi-Fi
the main settings of your appliance from your smartphone.
This accessory is not included inside the product packaging. Please contact our After-Sales Service for more details
and purchase.
64 178
- 14 -
Remote controller
Insert the batteries into RC
1. Insert a pin and gently press down on the battery
cover and push in the direction of the arrow to
remove, as shown.
2. Insert 2 AAA batteries (1.5V) into the compartment.
Ensure that “+” and “-” polarity is correctly positioned.
3. Close the battery cover on the remote control.
Remote Control presetting
Each time the batteries are replaced in the remote
controller, the remote controller pre-set at Heat Pump
mode. The heat pump AC remote controller can be
used to control the cool only AC models.
Use RC to control the appliance
To operate the appliance by remote control, point the
remote control at the receiving device on the indoor
unit, to ensure receiving sensibility.
To send a message from remote control, the symbol
will ash for 1 second. On receipt of the message, the
appliance will emit a beep.
The remote control will operate the air conditioner at
a distance of up to 7m.
Each time the batteries are replaced in the remote
control, the remote control is pre-set at Heat Pump
mode.
Note: please follow the intruction which matches to the remote controller you receive for Air Conditioner operation
.
Function description of buttons (P1-03)
1. ON/OFF BUTTON
Starts or Stops the appliance by
pressing this button.
3.FAN BUTTON
Used to select fan speed in sequence
auto, high, medium or low.
4-5.TEMPERATURE BUTTON
Used to select the room
temperature.
Used to set the time in timer mode.
6. 6th SENSE BUTTON
Sets or cancels 6th sense operation.
7. SWING BUTTON
Stops or starts horizontal adjustment
louver swinging and sets the desired
up/down airow direction.
10-11. HUMIDITY BUTTON
Used to set desired humidity level,
they are only available under 6th
SENSE mode.
16. SUPER SILENT BUTTON
Used to start or stop the super
silent operation to have a low noise
environment.
2. MODE BUTTON
Used to select the operation mode.
In sequence Cooling, hearing or fan..
8.SLEEP BUTTON
Used to select the sleep mode in
sequence of sleep 1, sleep 2, sleep 3
sleep 4 and sleep o.
9.AROUND U BUTTON
Used to set or cancel Around U
function.
12.JET BUTTON
Used to start or stop the fast cooling
or heating.
13.DIM BUTTON
Used to turn on or turn o display
light on indoor unit.
14.WI-FI BUTTON
Used to trun on or turn o the Wi-Fi.
15TIMER BUTTON
Used to set the time for turn on or
turn o the appliance.
Symbols on RC display Active RC by pressing UNLOCK button
Cooling indicator Auto fan speed Sleep indicator 1 Press the button, the
backlight will lighted up
and function buttons
will be activated for use.
Press again to lock remote
controller. If no operation
on remote controller
for 10s, the remote
controller will be locked
automatically.
PRESS
Humidity plus indicator High fan speed Sleep indicator 2
Humidity minus indicator Medium fan speed Sleep indicator 3
Fan only indicator Low fan speed Sleep indicator 4
Heating indicator Super silent indicator Display set temperature
Around U indicator 6th SENSE indicator
ON
OF F
Display set timer
Jet indicator Power save indicator Signal transmission
Signal receptor
- 15 -
Remote controller
Function description of buttons (J1-3A)
1. ON/OFF BUTTON
Starts or Stops the appliance by pressing this button.
2. MODE BUTTON
Used to select the operation mode in sequence of
Cooling, dry, fan only or heating.
3. FAN BUTTON
Used to select fan speed in sequence auto, high, medium or low.
4-5.TEMPERATURE BUTTON
Used to select the room temperature. Used to set time in
timer mode and real time clock.
6. 6TH SENSE BUTTON
Sets or cancels 6th sense operation.
7. SWING BUTTON
Stops or starts horizontal adjustment louver swinging
and sets the desired up/down airow direction.
8. SLEEP BUTTON
Sets or cancels Sleep Mode operation in sequence of
9. AROUND U BUTTON
Used to set or cancel Around U function.
10. TIMER ON/CLOCK BUTTON
Used to set the current time.
Used to set or cancel the timer on operation.
11 TIMER OFF BUTTON
Used to set or cancel the timer o operation.
12. JET BUTTON
Used to start or stop the fast cooling or heating mode.
13. DIM BUTTON
Used to turn on or turn o display light on indoor unit.
14. POWER SAVE BUTTON
Used to start or stop the power save operation.
15. SUPER SILENT BUTTON
Used to start or stop the super silent operation to have a
low noise environment.
rq
et
d
f
i
o
g
s
u
w
y
a
h
Symbols on RC display
Cooling indicator Sleep 1 indicator Auto fan speed Jet indicator
Dry indicator Sleep 2 indicator High fan speed Signal transmission
Fan only indicator Sleep 3 indicator Medium fan speed
ON
OF F
Display set timer
Heating indicator Sleep 4 indicator Low fan speed Display current time
6th Sense indicator Around U indicator Super silent indicator Display set temperature
Power save indicator
PROTECTION
Operating condition
The protective device maybe trip
and stop the appliance in the cases
listed below.
Heating Outdoor air
temperature is
over 24°C
Outdoor air
temperature is
below -7°C
Room temperature
is over 27°C
Cooling Outdoor air
temperature is
over 43°C
Room temperature
is below 21°C
Dehumidifying Room temperature
is below 18°C
If the air conditioner runs in
COOLING or DRY mode with door
or window opened for a long time
when relative humidity is above
80%, dew may drip down from the
outlet.
Features of protection device
Wait at least 3 minutes before
restarting the unit after operation
stops or changing mode during
operation. After connecting to
power supply and turning on the
appliance immediately, a delay of 20
seconds may occur before it starts to
operate. If all operation has stopped,
press ON/OFF button again to
restart. Timer should be set again if it
has been cancelled.
Features of COOLING mode
Anti-freezing
When the temperature of the indoor
heat exchanger drops to 0° or below,
compressor will stop working to
protect the appliance.
Features of HEATING mode
Preheating
In order to prevent cool air blowing,
2-5 minutes are necessary to
preheat the indoor unit at HEATING
operation start. The indoor fan will
not work during preheating.
Defrosting
In HEATING operation the appliance
will defrost (de-ice) automatically
to raise eciency. This procedure
usually lasts 6-10 minutes. During
defrosting, fan stops running and
running indicator ashes.
After defrosting is completeed,
it returns to HEATING mode
automatically.
- 16 -
Maintenance
Clean front panel of Indoor Unit
1. Disconnect from the power supply
Turn o the appliance rst before disconnecting from power supply.
2. Remove the front panel
Open the front panel as shown by the arrow (Fig. A).
Pull the slots at the side of the front panel with force to take out the front panel (Fig. B).
3. Clean the front panel
Wipe it with a soft and dry cloth. Use lukewarm water (below 40°C) to clean if the
appliance is very dirty. After cleaning let it dry.
4. Ret and close the front panel
Ret and close the front panel by pushing it downward.
Note:
Do not use substances such as gasoline or polishing powder to clean the
appliance.
Do not sprinkle water onto the indoor unit Dangerous! Electric shock!
Clean Air lter
It is necessary to clean the air lter after using it for about 200 hours.Clean the air lter
every two weeks if the air conditioner operates in an extremely dusty environment.
1. Disconnect from the power supply
Turn o the appliance rst before disconnecting from power supply.
2. Take out air lter (Fig. C).
1. Open the front panel. 2. Press the handle of the lter gently. 3. Slide out the lter.
3. Cleaning the air lter (Fig. D)
If the lter is very dirty, clean it with a solution of lukewarm water and neutral
detergent.
After cleaning let it dry.
4. Ret the lter, press the lter reset button (Fig.E) at right side by using a
cylinder pin and close the front panel.
Note:
To avoid injury, do not touch the ns of indoor unit with your ngers
after removing the lter.
Do not attempt to clean the inside of the air conditioner by yourself.
Do not clean the lter in washing machine.
EMERGENCY OPERATION
Under emergency situation or when remote control
is missing, you can control the unit by pressing the
on/o swith located on the indoor unit.
Turn on the appliance: when the unit is o, press
this button, it will start up and operate in 6th
SENSE mode.
Turn o the appliance: when the unit is on, press
this button, the unit will stop working.
Note: Do not press this button for a long time as it will cause malfunction.
Auto-Restart Function
If you want to set auto-restart, switch on the power supply, press the ON/OFF button on the indoor unit and hold for
over 5 seconds, auto-restart is set with buzz sound.
If the auto-restart has been set, press the ON/OFF button on the indoor unit and hold for over 5 seconds, auto-restart
function will be cancelled with a buzz sound and air conditioner is on standby mode.
Disposal of the batteries
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
Fig.A
Fig.B
Fig.C
Fig.D
Fig.E
Filter Reset button
on/o switch on/o switch
- 17 -
Installation instruction
Installation diagram
Distance from wall
should be over 50mm
Distance from ceiling
should be over 200mm
Distance from the wall
should be over 50mm
To get detail installation information ,
please go to : docs.whirlpool.eu
NOTE: The gure is only a simple
presentation of the unit, it may not mutch
the external appearance of the product you
purchased. Installation must be performed in
accordance with th national wiring standard
by authurized service people only.
Distance from oor
should be over 2500mm
Indoor unit
Outdoor unit
Air intake distance from the
wall should be over 250mm
Air intake distance from the
wall should be over 250mm
Air outlet distance from the wall
should be over 500mm
Over 250mm
When install interconnection cord , make sure that the color of wires and the terminal No. of outdoor unit shall be
same as those in indoor unit.
Cable Specications
Capacity (Btu/h) Power cord Power connecting cord
Type Normal cross -
sectional area Type Normal cross -
sectional area
7K, 9K, 12K H07RN-F 1.0mm2X3 H07RN-F 1.0mm2X5
18K H07RN-F 1.5mm2X3 H07RN-F 1.5mm2X5
24 K H07RN-F 2.5mm2X3 H07RN-F 2.5mm2X5
- 18 -
Troubleshooting
Operation problems are often due to minor causes, please check and refer to the following chart before
contacting the service. This may save time and unnecessary expenses.
Trouble Analysis
Does not run
Is the protection device or fuse blown?
Please wait for 3 minutes and start again, protection device may be preventing unit to work.
Are the remote control batteries low?
Is the plug not properly plugged?
No cooling or
heating air
Is the air lter dirty?
Are the intakes and outlets of the air conditioner blocked?
Is the temperature set properly?
Are doors or windows open?
Ineective control
Has there been a strong interference (from excessive static electricity discharge, power supply voltage
abnormality)? Note that operation will be abnormal, in this case unplug from the power supply and
re-plug after 2-3 seconds.
Does not operate
immediately 3 minute delay will occur when changing mode during operation.
Peculiar smell This smell may come from another source such as furniture, cigarette etc, which is sucked in the unit
and blown out with the air.
A sound of
running water Normal behaviour caused by the ow of refrigerant in the air conditioner.
Defrosting sound in heating mode.
Cracking sound The sound may be generated by the expansion or contraction of the front panel due to temperature
changes.
Mist sprays from
the outlet Mist is present in the room with low temperature? Normal behaviour due to cool air discharged from
indoor unit during COOLING or DRY operation mode.
Running indicator
ashes but indoor
fan stops. The unit is shifting from heating mode to defrost. The indicator will light o and return to heating mode.
Note: If the problems still have, turn o the appliance and disconnect from power supply, then contact the
nearest Whirlpool Authorized Service Center. Do not attempt to move, repair, disassemble, or modify the
appliance by yourself.
- 19 -
AFTER SALES SERVICE
Before contacting the Customer Care Centre:
1. Try to solve the problem yourself based on the
descriptions given in the Troubleshooting”.
2. Turn the appliance o and restart it to see if the fault
persists.
If after carrying out the above checks, the fault
persists, contact the Customer Care Centre.
Please give:
a short description of the fault;
the exact model of the air conditioner;
the service number (this is the number found below
the word Service on service sticker which is located
on the side or on the bottom of the indoor unit).
The service number can also be found in the warranty
booklet;
your full address;
your telephone number.
If repair work has to be carried out, contact the
Customer Care Centre (Use of original spare parts and a
proper repair is guarenteed).
You will need to present the original invoice.
Failure to comply with these instructions could
compromise the safety and quality of your product.
Note: if you want the full manual for your appliance, please help to download it from websit throught below
link: docs.whirlpool.eu using QR code.
- 20 -
DIESE MÜSSEN DURCHGELESEN UND BEACHTET WERDEN
Laden Sie die komplette Bedienungsanleitung auf docs.whirlpool.eu runter oder rufen
Sie die Telefonnummer auf dem Garantieheft an.
Diese Sicherheitsanweisungen vor dem Gebrauch durchlesen. Diese Anweisungen zum
Nachschlagen leicht zugänglich aufbewahren.
In diesen Anweisungen sowie auf dem Gerät selbst werden wichtige
Sicherheitshinweise angegeben, die durchgelesen und stets beachtet werden
müssen. Der Hersteller übernimmt keine Haftung für die Nichtbeachtung dieser
Sicherheitshinweise, für unsachgemäße Verwendung des Geräts oder falsche
Bedienungseinstellung.
Babys und Kleinkinder (0-3 Jahre) müssen vom Gerät fern gehalten werden. Jüngere
Kinder (3-8 Jahre) müssen vom Gerät fern gehalten werden, es sei denn, sie werden
ständig beaufsichtigt. Dieses Gerät darf von Kindern ab 8 Jahren sowie Personen mit
herabgesetzten physischen, sensorischen oder geistigen Fähigkeiten und Mangel an
Erfahrung und Kenntnissen nur unter Aufsicht oder nach ausreichender Einweisung
durch eine für ihre Sicherheit verantwortliche Person verwendet werden. Kinder dürfen
nicht mit dem Gerät spielen. Die Reinigung und Pege des Gerätes darf von Kindern
nicht ohne Aufsicht durchgeführt werden.
ZUGELASSENE VERWENDUNG
VORSICHT: Das Gerät ist nicht für den Betrieb mit einem externen Schalter, wie Timer,
oder separatem Fernbedienungssystem konstruiert.
Dieses Gerät ist für Haushaltsanwendungen und ähnliche Anwendungen konzipiert,
zum Beispiel: Hotels und Büros.
Dieses Gerät eignet sich nicht für den professionellen Einsatz.
Schalten Sie das Klimagerät immer erst mit der Fernbedienung aus. Schalten Sie dazu
nicht den Leitungsschutzschalter aus und ziehen Sie nicht den Stecker aus der Steckdose.
Trennen Sie das Klimaget vor einem längeren Nichtgebrauch und bei Gewitter vom
Stromnetz.
Stellen Sie keine Gegenstände auf die Außeneinheit - Verletzungsgefahr. Die
Lüftungsönungen dürfen nicht behindert werden.
Stellen bzw. legen Sie keinesfalls andere elektrische Produkte oder
Haushaltsgegenstände unter das Innengerät oder unter das Außengerät. Kondenswasser,
das aus dem Gerät tropft, kann dieses nass machen und Schäden oder Fehlfunktionen an
Ihrem Eigentum verursachen.
INSTALLATION
Zum Transport und zur Installation des Gerätes sind zwei oder mehrere Personen
erforderlich - Verletzungsgefahr. Schutzhandschuhe zum Auspacken und zur Installation
verwenden - Risiko von Schnittverletzungen.
Die Installation, einschließlich elektrischer Anschlüsse und Reparaturen
müssen von einem qualizierten Techniker entsprechend den vor Ort geltenden
Sicherheitsvorschriften durchgeführt werden. Das Gerät nicht selbst reparieren und
tauschen keine Teile austauschen, wenn dies von der Bedienungsanleitung nicht
ausdrücklich vorgesehen ist. Kinder vom Installationsort fern halten. Prüfen Sie das
Gerät nach dem Auspacken auf Transportschäden. Bei auftretenden Problemen wenden
Sie sich bitte an Ihren Händler oder den Kundenservice. Nach der Installation müssen
Verpackungsabfälle (Kunststo, Styroporteile usw.) außerhalb der Reichweite von
Kindern aufbewahrt werden - Erstickungsgefahr. Das Gerät vor Installationsarbeiten von
der netzfernen Stromversorgung trennen - Stromschlaggefahr. Während der Installation
sicherstellen, das Netzkabel nicht mit dem Gerät selbst zu beschädigen - Brand- oder
Stromschlaggefahr. Das Gerät erst starten, wenn die Installationsarbeiten abgeschlossen
sind.
Beim Umzug oder bei einer Neupositionierung der Klimaanlage müssen für die
Trennung und Neuinstallation der Anlage erfahrene Servicetechniker dazu gezogen
werden.
SICHERHEITSHINWEISE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324

Whirlpool SPIW309A3WF.1 Manuale utente

Categoria
Condizionatori d'aria a sistema split
Tipo
Manuale utente