![](//vs1.manuzoid.it/store/data-gzf/18dd8dcad50cbf7865a2ec34a42533fe/2/000343696.htmlex.zip/bg9.jpg)
5
O To remove a tool, reverse step 5 above. (Always use oven
gloves to remove tools after cooking).
6 To lower the mixer head, raise it slightly, then turn the head
lift lever clockwise.
Lower into the locked position.
Stir Tool – when using the stir tool the stir assist clip can also
be used to assist the mixing action, see ‘to fit and remove
your stir assist clip'. The stir tool can also be used with the
whisk. Do not use the stir tool with the dough tool.
To Use Your Cooking Chef Connect - Manual
Operation
1 Add the relevant ingredients to be cooked/mixed.
2 Set the required time, speed and temperature.
Note: To use the machine as a mixer without heat, select
'Off' when setting the temperature.
Turn the control dial anti-clockwise to use stir intervals and
pulse.
Turn the control dial clockwise to use continuous speeds.
3 Press the control dial to start.
4 To stop the unit at any time, press the control dial. If in
cooking mode, take care as the unit will be hot.
High speed, high temperature mode (HSHT)
To mix at high speed at temperatures of 60°C and above
O Select time (if applicable), speed and temperature of
60°C or above.
O A warning will pop up on the display screen advising that
you are entering HSHT mode
O Once the warning has been read and undestood, press
yes to confirm that you are happy to enter HSHT mode.
O Press the control dial to start.
This function MUST ONLY be used with the whisk and/
or stir tool. You should not exceed the maximum cooking
capacity of 3 litres and you must ensure the splashguard is
fitted. The machine must not be left unattended.
5 Once a programme has finished, the unit will beep 3 times.
O Note: If no time has been set, the heating and stirring
processes will automatically end once the timer has
reached 8 hours.
6 To stop the heating process, change the temperature to
‘OFF’. To stop the unit at any time press the control dial.
Important – If at any time the mixer head is raised during
an operation, the heating process will pause and the bowl
tool will stop and will not restart when the mixer head is
lowered. To restart the mixer, lower the mixer head and
press the control dial.
Using Preset Programmes
Refer to Illustrations P – R
1 Select the Preset Menu.
2 Choose the preset you wish to use.
3 Follow the instructions on the display screen.
4 To stop the unit at any time, press the control dial. Take
care as the bowl and tools will be hot.
After Cooking
O Be careful when handling or touching any part of the
appliance when being used in the cooking mode or after
cooking, IN PARTICULAR THE BOWL AND TOOLS as
they will remain HOT long after the appliance has been
switched off.
O Use the two side handles to remove and carry the bowl.
Use oven gloves when handling the hot bowl and hot
tools.
O The underside of the bowl will remain hot long after the
heating has stopped. Use caution when handling and use
the work surface protection mat provided to protect heat
sensitive surfaces.
Hints and Tips
O Some recipes, in particular those with a high water
content, will not be able to reach a cooking temperature
above 100°C (as this is the boiling point of water).
O When adding ingredients to the bowl during cooking,
turn the speed down and add the ingredients slowly and
evenly.
O To heat sauces quickly use a continuous stir setting.
O If using the splashguard during cooking, always
remove it before lifting the mixer head. Be aware of
condensation formed on the splashguard and heat
shield.
O When lifting the mixer head lift it slowly to allow any
liquid on the underside of the heat shield to flow back
into the bowl.
O Four stir delay functions are available which enable
you to select the appropriate amount of stirring for
individual recipes. Some recipes will require constant
stirring to stop ingredients from sticking to the
bottom of the bowl, whereas others will benefit from
intermittent stirring to maintain the texture of the food.
Manual Operation (Attachments)
1 Remove High speed outlet/Slow Speed outlet cover (if
applicable).
2 Fit attachment according to specific instructions
supplied.
3 Set the required time and speed (refer to illustrations
L - M). Press the control dial to start.
To stop the unit at any time, press the control dial again.
To Remove And Fit Outlet Covers
High-Speed Outlet Cover
1 To remove the cover, use the grip and lift upwards.
2 To fit, place the cover over the outlet and push
downwards.
Slow-Speed Outlet Cover
1 To remove the cover, use the grip on the underside and
pull outwards.
2 To fit, locate the catch at the top of the cover into the
outlet recess and push to clip into position.
To Use The Weighing Function
Refer to Illustrations S
1 Select the weighing function on the touch screen.
2 Fit the bowl.
3 Zero the scale.
4 Weigh the ingredients.
5 To change between units tap the unit button on the
weighing screen.
Note: Always place the appliance on a dry flat, stable surface
prior to weighing. Do not apply pressure to the mixer or bowl
whilst weighing as this will affect the accuracy of the scales.
The weighing function can be used with the mixer head in
either the down or up position.
The weighing function is accurate up to 6kg.