Ubiquiti UniFI UAP-AC Guida Rapida

Enterprise WiFi System

Model: UAP-AC

1

Introduction

Thank you for purchasing the Ubiquiti Networks

™

UniFi

™

Enterprise

WiFi System. The UniFi Enterprise WiFi System includes the UniFi

Controller software, which allows you to manage your wireless

network using a web browser.

This Quick Start Guide includes the warranty terms and is for use

with the UniFi AP-AC, model UAP-AC. The UniFi Enterprise WiFi

System also includes the necessary hardware for mounting the

unit on a wall or a ceiling. The UniFi AP can be powered by any of

the following:

• PoE GigE Adapter (included)

• PoE+ 802.3at compliant switch

• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO

Package Contents

UniFi AP AC Mounting Bracket Ceiling Backing Plate

M3x50 Flat Head

Screws (Qty. 4)

M3 Keps Nuts

(Qty. 4)

M2.9x20 Screws

(Qty. 4)

M3x20 Screw

Anchors (Qty. 4)

Enterprise WiFi System

Model: UAP-AC

UniFi Controller

CD with User Guide

PoE GigE Adapter

(48V, 0.5A Gigabit)

Power Cord Quick Start Guide

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

2

UniFi

™

AP-AC Quick Start Guide

System Requirements

• Microsoft Windows Vista, Windows 7, Windows 8, or Mac OS X

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address as

well as for the wireless clients after deployment)

• A management station computer running the UniFi Controller

software, located either onsite and connected to the same

Layer-2 network, or off-site in a cloud or NOC

or

Router

O-Site

Cloud/NOC

On-Site

Management Station

UAP-AC

UAP/UAP-LR

UAP-PRO

UAP-Outdoor

Sample Network Diagram

All UniFi APs support off-site management controllers. Refer to the

User Guide on the CD for setup details.

3

Hardware Overview

LED

LED Color Status

Flashing white Initializing.

Steady white Factory default, waiting to be integrated.

Alternating

white/blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such as a

firmware upgrade is taking place.

Quickly flashing

blue

This is used to locate an AP.

When you click Locate in the UniFi Controller

software, the AP will flash. It will also display

the location of the AP on the map.

Steady blue Indicates the device has been successfully

integrated into a network and is working

properly.

Steady blue

with occasional

flashing

Indicates the device is in an isolated state (all

WLANs are brought down until an uplink is

found).

4

UniFi

™

AP-AC Quick Start Guide

Ports

MAIN SECONDARY

Reset

This device complies with Part 15 of FCC rules.

Operation is subject to the following 2 conditions:

1) this device may not cause ha rmful interfe rence

and, 2) this device must ac cept any interfe rence

received, including interference that may cause

undesired operation.

FCC ID: SWX- UAPAC IC: 6545A-UAPAC

0560

M/N: UAP- AC 48V 0.5A POE

AP AC

|

Main Port

Secondary Port

Reset Button

Cable Feed Plug

Locking

Notch

Locking

Clip

Mounting Bracket

Main The Main port is a Gigabit Ethernet port used to connect

the power and should be connected to the LAN and DHCP server.

Power can be provided by any of the following:

• PoE GigE Adapter (included)

• PoE+ 802.3at compliant switch

• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO

Secondary The Secondary port is a Gigabit Ethernet port used for

bridging.

Reset The Reset button serves two functions:

• Restart It will restart the device when you press and release it

quickly.

• Restore Factory Defaults When you press and hold it for more

then 5 seconds, it will restore the device to the factory default

settings.

Locking Clip During installation, the Locking Clip on the Mounting

Bracket locks into the Locking Notch on the UniFi AP to help

prevent easy removal of the UniFi AP.

Cable Feed Plug If your Ethernet cable feeds along the mounting

surface, remove the Cable Feed Plug.

5

Installation Requirements

• CAT5/6 cable

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 25 mm hole for

Ethernet cable feed)

Hardware Installation

The UniFi AP can be mounted on the wall or ceiling. Perform the

steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on the

wall with the cable feed slot pointed towards the floor.

2. Use a pencil to mark the four mounting holes. Use a 6 mm drill

bit to drill the mounting holes.

Top

Optional 25 mm Hole for

Ethernet Cable Feed through Wall

3. Follow the instruction for your type of Ethernet cable feed:

- Feeds Through the Wall Cut or drill a circle approximately

25 mm in diameter, just below the bottom center of the

Mounting Bracket (as shown above). Then feed the CAT5/6

cable through the hole.

- Feeds Along the Mounting Surface Remove the Cable

Feed Plug on the side of the UniFi AP.

6

UniFi

™

AP-AC Quick Start Guide

4. Insert the M3x20 Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the M2.9x20 Screws

into the anchors.

5. Connect the Ethernet cable to the Main port. If the feed is

along the mounting surface, feed the cable through the Cable

Feed of the UniFi AP.

MAIN SECONDARY

RESET

This device complies with Part 15 of FCC rules.

Operation is subject to the following 2 conditions:

1) this device may not cause har mful interfere nce

and, 2) this device must acc ept any interfere nce

received, including interference that may cause

undesired operation.

FCC ID: SWX-U APAC IC: 6545A-UAPAC

0560

M/N: UAP-A C 48V 0.5A POE

AP AC

|

7

Hardware Installation

6. Align the slots on the UniFi AP with the tabs on the Mounting

Bracket.

7. Slide the UniFi AP down until it locks into place.

8

UniFi

™

AP-AC Quick Start Guide

Ceiling Mount

1. Remove the ceiling tile.

2. Place the Ceiling Backing Plate in the center of the ceiling tile.

Mark the four mounting screw holes and 25 mm hole for the

Ethernet cable feed.

25 mm Hole for Ethernet Cable Feed

3. Use a 3 mm drill bit to drill the screw holes, and cut or drill the

hole for the Ethernet cable feed.

9

Hardware Installation

4. Secure the Mounting Bracket to the ceiling tile using the Ceiling

Backing Plate, M3x50 Flathead Screws, and M3 Keps Nuts.

5. Feed the Ethernet cable through the 25 mm hole.

6. Set the ceiling tile back into place.

10

UniFi

™

AP-AC Quick Start Guide

7. Connect the Ethernet cable to the Main port.

MAIN

SECONDARY

This device complies with Part 15 of FCC rules.

Operation is subject to the following 2 condit ions:

1) this device may not cause harmful inte rference

and, 2) this de vice must acce pt any interfe rence

receive d, includin g interfer ence that m ay cause

undes ired op eratio n.

FCC ID: SWX-U APAC IC: 65 45A -U APA C

056 0

M/N : UAP -AC 48V 0.5A POE

AP AC

|

8. Align the slots on the UniFi AP with the tabs on the Mounting

Bracket.

11

Powering the UniFi AP

9. Slide the UniFi AP down until it locks into place.

Powering the UniFi AP

The UniFi AP can be powered directly by a compatible PoE switch

or with the included PoE GigE Adapter.

Connecting to a PoE Switch

Connect the other end of the Ethernet cable coming from the

Main port on the UniFi AP directly to a PoE port on one of the

following:

• PoE+ 802.3at compliant switch

• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO

TOUGHSwitch PRO Power Connection Diagram

12

UniFi

™

AP-AC Quick Start Guide

Connecting to the PoE GigE Adapter

1. Connect the other end of the Ethernet cable coming from the

Main port on the UniFi AP to the Ethernet port labeled POE on

the PoE GigE Adapter.

2. Connect an Ethernet cable from your LAN to the Ethernet port

labeled LAN on the PoE GigE Adapter.

3. Connect the power cord to the power port on the PoE GigE

Adapter. Connect the other end of the power cord to a power

outlet.

13

Software Installation

Insert the UniFi Controller software CD into your CD-ROM drive

and follow the instructions for your specific computer type.

Mac Users

1. Click the Install icon.

2. Click Continue and follow the on-screen instructions to install

the software.

14

UniFi

™

AP-AC Quick Start Guide

3. Go to Go > Applications and double-click the UniFi icon.

Proceed to Configuring the UniFi Controller Software on page 16.

PC Users

1. Launch UniFi-installer.exe.

2. Click Install.

3. If your computer doesn't have Java 1.6 or above installed, you

will be prompted to install it. Click Install to continue.

15

Software Installation

4. Click Next.

5. Ensure that the Start UniFi Controller after installation option is

checked and click Finish.

Note: The UniFi Controller software can also be launched

from Start > All Programs.

16

UniFi

™

AP-AC Quick Start Guide

Configuring the UniFi Controller Software

1. The UniFi Controller software startup will begin. Click Launch a

Browser to Manage Wireless Network.

2. Select your language and country. Click Next.

Note: U.S. product versions are locked to the U.S. Country

Code to ensure compliance with FCC regulations.

3. Select the devices that you want to configure and click Next.

17

Software Installation

4. The UniFi Installation Wizard will create a secure primary

wireless network for your devices. Perform the following steps:

a. Enter the wireless network name (SSID) in the Secure SSID

field.

b. Enter a passphrase to be used for your primary network.

c. If you want to enable guest access, select Enable Guest

Access, and enter a guest network name in the Guest SSID

field.

d. Click Next.

5. Enter an admin name and password to use when accessing the

management interface. Confirm your password in the Confirm

field. Click Next.

18

UniFi

™

AP-AC Quick Start Guide

6. Review your settings. Click Finish to save your settings or Back

to make changes. Once the wizard is finished, the browser will

be redirected to the management interface.

Congratulations, your wireless network is now configured.

A login screen will appear for the UniFi Controller management

interface. Enter the Admin Name and Password that you created

and click Login.

You can manage your wireless network and view network statistics

using the UniFi Controller management interface. For information

on configuring and using the UniFi Controller software, refer to the

User Guide located on the CD or documentation.ubnt.com/unifi

La pagina sta caricando ...

Ubiquiti UniFI UAP-AC Guida Rapida

Ubiquiti UniFI UAP-AC Guida Rapida

in altre lingue

Documenti correlati