Yamaha R-V702 Manuale utente

Categoria
Lettori di cassette
Tipo
Manuale utente

Questo manuale è adatto anche per

OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
Natural Sound AV Receiver
Récepteur audiovisuel “Son Naturel”
Receptor AV de Sonido Natural
R-V702
R-V502
Thank you for selecting this YAMAHA AV receiver.
Nous vous remercions d’avoir porté votre choix sur ce récepteur audiovisuel YAMAHA.
Muchas gracias por haber adquirido este receptor AV YAMAHA.
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the
manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause
the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
1
English
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE (for US customers only)
This device is a composite system. The digital device
component may not cause harmful interference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (for US customers only)
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime (for US customers only)
CONTENTS
2
Safety Instructions ...............Inside the Front Cover
Supplied Accessories ......................................2
Features ..........................................................3
Caution ............................................................4
Notes about the Remote Control Transmitter
........................................................................5
Profile of This Unit ...........................................6
Speaker Setup ................................................7
Connections ....................................................8
Controls and Their Functions ........................14
Speaker Balance Adjustment ........................20
Basic Operations ...........................................23
Tuning Operations .........................................26
Preset Tuning ................................................27
Using Digital Sound Field Processor (DSP)
......................................................................30
Setting the SLEEP Timer ..............................34
Troubleshooting .............................................35
Specifications ................................................36
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are included.
Indoor FM Antenna
AM Loop Antenna
Antenna adapter (U.S.A. and Canada models only)
Batteries (size AA, R6, UM-3)
Remote Control Transmitter
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
DELAY/CENTER
/REAR
DVD/LD
VCR
TV/DBS
R-V702 R-V502
FEATURES
3
English
5 Speaker Configuration
R-V702
<
U.S.A. and Canada models
>
Main: 80W + 80W (8) RMS Output
Power, 0.09% THD, 1 kHz
Center: 80W (8) RMS Output
Power, 0.09% THD,
1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.7% THD, 1 kHz
<
Australia and General models
>
Main: 80W + 80W (8) RMS Output
Power, 0.09% THD, 1 kHz
Center: 80W (8) RMS Output
Power, 0.09% THD,
1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.7% THD, 1 kHz
R-V502
<
U.S.A. model
>
Main: 70W + 70W (8) RMS Output
Power, 0.09% THD, 1 kHz
Center: 70W (8) RMS Output
Power, 0.09% THD, 1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.7% THD, 1 kHz
<
Australia, Canada and General
models
>
Main: 60W + 60W (8) RMS Output
Power, 0.09% THD, 1 kHz
Center: 60W (8) RMS Output
Power, 0.09% THD, 1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.7% THD, 1 kHz
Digital Sound Field Processor
Dolby Pro Logic Surround Decoder
Theater-like Sound Experience by the
Combination of Dolby Pro Logic and
YAMAHA DSP Technology (CINEMA DSP)
Automatic Input Balance Control for
Dolby Pro Logic Surround
Test Tone Generator for Easier Speaker
Balance Adjustment
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
IF Count Direct PLL Synthesizer Tuning
System
Video Signal Input/Output Capability
SLEEP Timer
Remote Control Capability
4
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Make sure to allow a space of at least
10 cm behind, 20 cm on the both sides and 30 cm above
the top panel of the unit. Otherwise it may not only damage
the unit, but also cause fire.
6. Always set the VOLUME control to “–
” before starting
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
5
English
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will not
be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
1
3
2
l6
20
28
40
60
l2
8
4
2
0
–dB
l6
20
28
40
60
l2
8
4
2
0
–dB
30°
30°
Remote control
sensor
Within approximately
6 m (19.7 feet)
R-V502
R-V702
6
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround
Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic employs a four channel five speaker system. The Pro
Logic Surround system divides the input signal into four levels:
the left and right main channels, the center channel (used for
dialog), and the rear surround sound channels (used for sound
effects, background noise, and other ambient noises). The
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from the action on the
screen while experiencing good stereo imaging.
Dolby Surround is encoded on the sound track of pre-recorded
video tapes, laser discs, and some TV/cable broadcasts. When
you play a source encoded with Dolby Surround on this unit,
the Dolby Pro Logic Surround decoder decodes the signal and
distributes the surround-sound effects.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system improves the stability of
sound at each channel and minimizes crosstalk between
channels, so that positioning of sounds around the room is
more accurate compared with conventional analog signal
processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, the double-D symbol and “Pro Logic” are
trademarks of Dolby Laboratories Licensing Corporation.
Dolby Pro Logic Surround + DSP
Dolby Surround sound system shows its full ability in a large
movie theater, because movie sounds are originally designed
to be reproduced in a large movie theater using many
speakers. It is difficult to create a sound environment similar to
that of a movie theater in your listening room, because the
room size, materials of inside walls, the number of speakers,
etc. of your listening room is much different from those of a
movie theater.
Yamaha DSP technology made it possible to present you with
nearly the same sound experience as that of a large movie
theater in your listening room by compensating for lack of
presence and dynamics in your listening room with its original
digital sound fields combined with Dolby Surround sound field.
The combination of Dolby Pro Logic Surround and DSP is used
on the sound field program “ PRO LOGIC ENHANCED”.
The YAMAHA “CINEMA DSP” logo indicates these programs are
created by the combination of Dolby Pro Logic and YAMAHA
DSP technology.
CINEMA DSP
7
English
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main
speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED is selected, conversations
will be output from the center speaker and the ambience will be
excellent.
Set the center channel mode to the “NORMAL” or “WIDE
position. (For details, refer to page 21.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected, the center sound is output from the
left and the right main speakers. However, the sound effect of
other programs can be the same as that of the 5-speaker
configuration.
Be sure to set the center channel mode to the “PHANTOM
position. (For details, refer to page 21.)
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Main: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the main speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
Main L
Main R
Main L
Main R
Main L
Main R
8
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “” to “”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure
to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
1
,
*
2
: See the next page.
(U.S.A. model)
To AC outlet
Turntable
LD player etc.
Video cassette recorder
TV/Satellite tuner
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
R-V702
9
English
AC OUTLET(S) (SWITCHED)
(U.S.A., Canada and General models)
.......................................................... 2 SWITCHED OUTLETS
(Australia model) ................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLET(S) is
100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
*
1
*
2
R-V502
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
MONITOR OUT
VIDEO
IN OUTVCR
VIDEO SIGNAL
CD
TAPE
( MD )
VIDEOPHONO VCR
TAPE
PB
REC
OUT
IN OUT
AUDIO SIGNAL
3 4
1
CENTER
OUTPUT
SUB
WOOFER
REAR
CENTER
CD
DUAL
SINGLE
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
MAIN
SPEAKERS
A
B
MAINS
REAR
6MIN./SPEAKER
SINGLE
:
6MIN./SPEAKER
DUAL
:3MIN./SPEAKER
A OR B
:4MIN./SPEAKER
A B
:8MIN./SPEAKER
REAR
8MIN./SPEAKER
SINGLE
:
8MIN./SPEAKER
DUAL
:4MIN./SPEAKER
A OR B
:8MIN./SPEAKER
A B
:
I6
MIN./SPEAKER
CENTER
MAIN
CENTER
MAIN
IMPEDANCE SELECTOR
GND
OUTPUT
LINE OUT
LINE IN
OUTPUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO IN
VIDEO OUT
AUDIO OUT
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS
(U.S.A. model)
To AC outlet
Turntable
LD player etc.
Video cassette recorder
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
10
CONNECTING SPEAKERS
CENTER
OUTPUT
SUB
WOOFER
REAR
CENTER
CD
DUAL
SINGLE
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
MAIN
SPEAKERS
A
B
REAR
6MIN./SPEAKER
SINGLE
:
6MIN./SPEAKER
DUAL
:3MIN./SPEAKER
A OR B
:4MIN./SPEAKER
A B
:8MIN./SPEAKER
CENTER
MAIN
REAR
8MIN./SPEAKER
SINGLE
:
8MIN./SPEAKER
DUAL
:4MIN./SPEAKER
A OR B
:8MIN./SPEAKER
A B
:
I6
MIN./SPEAKER
CENTER
MAIN
IMPEDANCE SELECTOR
Rear speaker Rear speaker
Center speaker
Main speakers B
Left
Right
Left
Right
Main speakers A
Subwoofer system
Left
Right
Note
Use speakers with the specified impedance shown on the rear
of this unit.
Note on main speaker connections:
One or two speaker systems can be connected to this unit. If
you use only one speaker system, connect it to either the
SPEAKERS A or B terminals.
Note on a subwoofer connection:
You may wish to add a subwoofer to reinforce low frequencies.
Connect the SUBWOOFER OUTPUT terminal of this unit to
the INPUT terminal of the subwoofer amplifier, and connect the
speaker terminals of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
Note on center speaker connection:
One or two center speakers can be connected to this unit. If
you cannot place the center speaker on or under the TV, it is
recommended to use two center speakers and place them on
both sides of the TV to orient the center sound at the center
position. For connecting two center speakers, follow the
method shown below.
REAR
CENTER
CD
DUAL
SINGLE
Center speaker
Center speaker
(U.S.A. model)
11
English
For connecting to the MAIN SPEAKERS terminals
Red: positive (+)
Black: negative (–)
Unscrew the knob.
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Tighten the knob and
secure the wire.
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
Press the tab.
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Release the tab and
secure the wire.
1
2
3
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage
this unit and/or speakers.
12
CENTER OUTPUT terminal
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
SUBWOOFER OUTPUT terminal
This terminal is for connecting with the input terminal of an
amplifier for driving a subwoofer.
This terminal outputs only frequencies below 200 Hz from the
main and center channels.
Note
Output level of signals from these terminals are adjusted
by the use of VOLUME control on the front panel or VOLUME
keys on the remote control transmitter.
OUTPUT terminals (for driving speakers with external amplifiers)
Be sure to switch this only when the power of this unit is turned
off.
Select the position whose requirements your speaker system
meets.
(Upper position)
Rear: The impedance of each speaker must be 6or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 6or higher.
If you use two center speakers, the impedance of
each speaker must be 3or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 4or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8or higher.
(Lower position)
Rear: The impedance of each speaker must be 8or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 8or higher.
If you use two center speakers, the impedance of
each speaker must be 4or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 8or higher.
<Except Canada model>
If you use two pairs of main speakers, the impedance
of each speaker must be 16or higher.
IMPEDANCE SELECTOR switch
REAR
6MIN./SPEAKER
SINGLE
:
6MIN./SPEAKER
DUAL
:3MIN./SPEAKER
A OR B
:4MIN./SPEAKER
A B
:8MIN./SPEAKER
CENTER
MAIN
REAR
8MIN./SPEAKER
SINGLE
:
8MIN./SPEAKER
DUAL
:4MIN./SPEAKER
A OR B
:8MIN./SPEAKER
A B
:
I6
MIN./SPEAKER
CENTER
MAIN
IMPEDANCE SELECTOR
CENTER
OUTPUT
SUB
WOOFER
(U.S.A. model)
13
English
ANTENNA CONNECTIONS
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
Orient so that the best
reception is obtained.
1 2 3
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm/300-ohm
antenna adapter
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
300-ohm feeder
Indoor FM
antenna
(included)
14
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
POWER
NATURAL SOUND AV RECEIVER
R–V702
SPEAKERSPHONES
A
ON
B
OFF
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
CINEMA DSP
55
4
3
2
l
0
l
2
3
4
DELAY/
CENTER/REAR
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DISCO
CONCERT
HALL
ROCK
CONCERT
EFFECT
DOWN
TUNING
UP
MEMORY
EDIT
TIME
/
LEVEL
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
VCR DVD
/
LDTV
/
DBS
TAPE (MD)
MONITOR
TUNER
CD
PHONO
1
90 A B C D FGI JK
EH
23 4 5 6 8
7
POWER
NATURAL SOUND AV RECEIVER
R–V502
SPEAKERSPHONES
A
ON
B
OFF
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
CINEMA DSP
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE (MD)
MONITOR
VIDEOVCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
1
90 A B C D FGI L
M NK
E
7H
23 4 5 8
R-V702
R-V502
15
English
1 POWER switch
Press this switch to switch the power on. Press it again to
switch the power off.
2 Standby mode indicator
(Except U.S.A. and Canada models)
While the power is on, pressing the SYSTEM POWER OFF
key on the remote control transmitter switches the unit to the
standby mode. In this mode, this indicator is illuminated.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 Display panel
Shows various information. (Refer to page 17 for details.)
5 Input selector buttons
Select a program source to listen to or watch. When a button is
pressed, the name of selected source appears on the display.
6 DSP program selector buttons
R-V702 only
Select a DSP program. When a button is pressed, the name of
selected program lights up on the display.
7 EFFECT button
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
8 VOLUME control
Used to raise or lower the volume level.
9 PHONES jack
When you listen with headphones, connect the headphones to
the PHONES jack. You can listen to the sound to be output
from the main speakers through headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
button.
0 SPEAKERS switches
Set the switch A or B (or both A and B) for the main speaker
system (connected to this unit) you will use to the ON position.
Set the switch for the main speaker system you will not use to
the OFF position.
A A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
B Preset station number selector buttons
Select a preset station number (1 to 8).
C Tone controls
These controls are effective only for the sound from the main
speakers.
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
D BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
E FM/AM buttons
Press this button to switch the reception band to FM or AM.
PHONES
16
F MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the MEMORY indicator flashes for
about 5 seconds. During this period, select a desired preset
station number by pressing the corresponding preset station
number selector button to enter the displayed station into the
memory.
When this button is pressed and held for about 3 seconds, the
automatic preset tuning begins. (Refer to page 28 for details.)
G EDIT button
This button is used to exchange the places of two preset
stations with each other.
H TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
I TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that “AUTO” lights up on the display. To select the
manual tuning mode, press this button so that “AUTO” goes
off.
J DELAY/CENTER/REAR and TIME/LEVEL +/– buttons
R-V702 only
Adjust the delay time (DELAY), the rear channel output level
(REAR) and the center channel output level (CENTER).
Select the item which you want to adjust by pressing the
DELAY/CENTER/REAR button and adjust its time or level by
pressing the TIME/LEVEL +/– button.
K CENTER MODE button
Selects a center channel output mode (NORMAL, WIDE or
PHANTOM). (For details, refer to page 21.)
L PROGRAM selector button
R-V502 only
When the built-in digital sound field processor (including the
Dolby Pro Logic Surround decoder) is on, this button changes
the currently selected DSP program whenever the right or left
side of this button is pressed.
M CENTER LEVEL control
R-V502 only
Adjusts the sound output level of the center speaker.
N REAR LEVEL control
R-V502 only
Adjusts the sound output level of the rear speakers.
17
English
DISPLAY PANEL
PRESET
kHz
MHz
MEMORY
AUTO
SLEEP
TAPE MON
STEREO
0
20
l00
ms dB
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK CONCERT
CONCERT HALL
NORM
WIDE
PHANTOM
EFFECT OFF
123
56
9
0
87
4
1 Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected input source.
2 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
3 Signal-level meter
Indicates the signal level of the received station.
If multipath interference is detected, the indication decreases.
4 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
5 Center channel mode indicators
The name of a selected center channel mode lights up only
when a program which uses the Dolby Pro Logic Surround
decoder is selected.
6 EFFECT OFF indicator
Lights up if neither the digital sound field processor nor the
Dolby Pro Logic Surround decoder is on. In this state, sound
output is 2-channel stereo.
7 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
8 MEMORY indicator
When the MEMORY button is pressed, this indicator flashes
for about 5 seconds. During this period, the displayed station
can be programmed to the memory by using the A/B/C/D/E
button and the preset station number selector buttons.
9 TAPE MON indicator
Lights up when the tape deck (or MD recorder etc.) is selected
as the input source by pressing the TAPE (MD) MONITOR
button.
0 DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor and/or the Dolby Pro Logic
Surround decoder is on.
18
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
DELAY/CENTER
/REAR
DVD/LD
VCR
TV/DBS
2
3
4
2
8
9
6
7
5
1
1
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
2
3
4
2
8
9
6
7
5
1
1
R-V502
R-V702
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Yamaha R-V702 Manuale utente

Categoria
Lettori di cassette
Tipo
Manuale utente
Questo manuale è adatto anche per