Somfy ROLL UP 28 WIREFREE Istruzioni per l'uso

Roll Up 28 WF RTS II

EN Instructions

FR Notice

DE Anleitung

IT Istruzioni

ES Manual de instrucciones

PT Instruções

EL Οδηγίες

AR 

EN Roll Up 28 WF RTS II

ORIGINAL INSTRUCTIONS

These instructions apply to all Roll Up 28 WF RTS II drives, the different versions of

which are available in the current catalogue.

CONTENTS

1.

Prior information...........................................................................................

4

1.1.

Field of application............................................................................

4

1.2.

Liability ...............................................................................................

4

2.

Installation......................................................................................................

5

2.1.

Assembly ............................................................................................

5

2.2.

Wiring .................................................................................................

6

2.3.

Commissioning ..................................................................................

7

2.4.

Tips and advice on installation.........................................................

9

3.

Use and maintenance ....................................................................................

13

3.1.

Mode selection: Roller or Tilting Mode..........................................

13

3.2.

Controlling Up, Down, my: in Roller mode ....................................

14

3.3.

Controlling Up, Down, my: in Tilting mode....................................

15

3.4.

Favourite position (my) ....................................................................

15

3.5.

Adjusting the speed...........................................................................

16

3.6.

Tips and advice on operation...........................................................

17

4.

Technical data ................................................................................................

19

Roll Up 28 WF RTS II EN

GENERAL INFORMATION

Safety instructions

DANGER

Indicates a danger which may result in immediate death or

serious injury.

WARNING

Indicates a danger which may result in death or serious

injury.

PRECAUTION

Indicates a danger which may result in minor or moderate

injury.

CAUTION

Indicates a danger which may result in damage to or

destruction of the product.

EN Roll Up 28 WF RTS II

1.PRIOR INFORMATION

1.1.Field of application

The R28 drives are designed to motorise all types of:



Interior vertical blinds which front rail moves solely by gravity with a mass less

than 15kg.

1.2.Liability

Before installing and using the drive, please read these instructions carefully.

In addition to the instructions provided in this guide, please also comply with the

instructions provided in the attached Safety instructions document.

The drive must be installed by a home motorisation and automation

professional, in accordance with Somfy’s instructions and the applicable

regulations in the country of installation.

Any operation of the drive outside the field of application described above is

prohibited. Such use, and any failure to comply with the instructions given in this guide

and in the attached Safety instructions document, absolves Somfy of any liability and

invalidates the warranty.

After installing the drive, the installer must inform his customers of the operating and

maintenance conditions for the drive and must provide them with the operating and

maintenance instructions, and the attached Safety instructions document. Any After-

Sales Service operation on the drive must be performed by a home motorisation and

automation professional.

Never begin installing without first checking the compatibility of this product with the

associated equipment and accessories. If in doubt when installing this product and/or

to obtain additional information, contact a Somfy representative or visit the website

www.somfy.com.

Using this drive with any products which are not listed in the attached

«Compatibility matrix» document shall also render invalid any Somfy warranty

and release Somfy from any liability.

Roll Up 28 WF RTS II EN

2.INSTALLATION

CAUTION

•

These instructions are mandatory for the home motorisation and

automation professional installing the drive.

•

Never drop, knock or puncture the drive or immerse it in liquid.

•

Install an individual control point for each drive.

NOTICE

Make sure that LED, programming button and input connection remain visible and

easily accessible after installation.

2.1.Assembly

2.1.1.Preparing the drive

CAUTION

Roll Up 28 WF RTS II : interior diameter of the tube has to be Ø26.6 mm or

greater.

1] Fit the crown (a) and drive wheel (b) to the

motor.

2] Measure the length (L) between the end of

the drive wheel and the head end.

L

1]

(a)(b)

2]

2.1.2.Preparing the tube

1] Cut the tube to the required length.

2] Deburr the tube and remove the debris.

1] 2]

EN Roll Up 28 WF RTS II

2.1.3.Assembling the drive-tube

1] Slide the drive into the tube. Insert the

wheel by aligning the wheel to the tube

profile. Insert the drive half way and then

slide the crown down the drive and insert

it in the tube. Finally, push the motor

inside the tube.

2] Not required, but if needed, fix the tube to

the drive with self-tapping screws or steel

pop rivets depending on the dimension (L).

1]

2]

L

2.1.4.Mounting the tube-drive assembly on the brackets

(a) Standard bracket.

(b) Drive plate for specific bracket.

(a) (b)

NOTICE

For optimal radio reception, the motor antenna should be kept straight and

should be positioned outside of headrail (if used).

2.2.Wiring

WARNING

•

To ensure electrical safety, this Class III drive must be powered by a «SELV»

voltage source (Safety Extra Low Voltage).

•

Improper using battery pack may cause overheat, fire, explosion, resulting in

serious injury or death.

•

Do not expose the drive or battery to excessive temperatures.

•

There is a risk if terminals of the battery-operated drive or battery being

short circuited by metal objects.

Roll Up 28 WF RTS II EN

CAUTION

•

Ensure battery is fully charged prior to installation on site.

•

Do not unplug the battery when the drive works.

•

Using this drive with any products which are not listed in the attached

«Compatibility matrix» document shall also render invalid any Somfy

warranty and release Somfy from any liability.

•

For the purposes of recharging the battery, only use the detachable supply

unit provided with this drive.

Plug the battery with the motor supply cable.

2.3.Commissioning

NOTICE

- Orange LED blinks continuously in setting mode.

- Green LED blinks once when any order from paired remote is received.

2.3.1.Pre-programming the control point

Press the Up and Down buttons simultaneously

on the control point:

→ The motorised product moves up and down.

The control point is pre-programmed.

EN Roll Up 28 WF RTS II

2.3.2.Checking the direction of rotation

Press the Up button on the control point:

a] If the motorised product rises, the direction of

rotation is correct: move onto section Setting

the end limits.

b] If the motorised product lowers, the direction

of rotation is incorrect: move onto the next step.

b1] Press the my button on the control point until

the motorised product moves up and down: The

direction of rotation has been modified.

b2] Press the Up button on the control point to

check the direction of rotation.

a]

b]

b1] b2]

2.3.3.Setting the end limits

NOTICE

The end limits can be set in any order.

1] Press and hold the Up button to move the

motorised product to the desired up

position. If necessary, adjust the up

position using the Up or Down buttons.

2] To memorize the upper end limit: Press

the my and Down buttons simultaneously

and release once the motorised product

begins to move. The upper end limit is

now memorized and green LED blinks 5

times.

3] Press the my button when the motorised

product reaches the desired down

position. If necessary, adjust the down

position using the Up or Down buttons.

4] To memorize the lower end limit: Press

the my and Up buttons simultaneously

and release when the motorised product

begins to move and green LED blinks 5

1] 2]

3]

5]

4]

Roll Up 28 WF RTS II EN

times. The lower end limit is now

memorized. The motorised product

moves up and stops at its upper end limit.

5] To confirm and complete end limits

programming: Press and hold the my

button until the motorised product briefly

moves up and down. The end limits are

now programmed.

2.3.4.Recording “Pairing” the control point

After recording the end limits:



Briefly press the control point PROG

button.



The motorised product briefly moves up

and down to confirm pairing.

→ The control point is recorded “paired” to the

motorised product and green LED blinks 5 times.

0.5 s

PROG.

2.4.Tips and advice on installation

2.4.1.Questions about the product?

Observations Possible causes Solutions

The motorised product

does not operate.

The drive battery is low and

requires charge. Red LED

blinks 5 times when any

button of a paired control

point is pressed.

Charge the battery.

The control point battery is

low. LED doesn't light

when any button of a

paired control point is

pressed.

Check the battery and

replace it as required.

EN Roll Up 28 WF RTS II

Observations Possible causes Solutions

The control point is not

compatible or not

programmed. LED doesn't

light when any button of

control point is pressed.

Check the compatibility or

pair the control point as

required referring to

Adding/Deleting control

points [}18].

An obstacle hinders the

movement of the

motorised product. The

Red LED lights fixed on.

Remove the obstacle.

Drive position is out of the

end limits. Red LED blinks 2

times intermittently and

continually.

Proceed to section

Readjusting the end limits

[}11].

The drive is neither set nor

paired. Orange LED lights

fixed on.

Proceed to section

Commissioning [}7]

The thermal protection has

activated. LED blinks red

continuously.

Wait for the drive to cool

down (LED will switch off).

The motorised product

stops too soon.

The end limits are

incorrectly set.

Reset the end limits

referring to Readjusting

the end limits [}11].

The motorised product has

exceeded recommended

weight limit.

Replace motorised

product.

The drive battery is low and

requires charge. Red LED

blinks 5 times when any

button of a paired control

point is pressed.

Charge the battery.

Roll Up 28 WF RTS II EN

Observations Possible causes Solutions

Setting is not allowed. The

drive moves briefly 3 times

in one direction and 3 times

in the other direction. Red

LED blinks 3 times and 3

times intermittently.

Maximum number of

control points reached.

Erase control points from

memory referring to

Erasing control points

from memory [}13].

Maximum/minimum value

of the setting is reached.

Perform correct setting.

End limits are too close. Readjust the end limits

referring to Readjusting

the end limits [}11].

Red LED blinks slowly for 3

seconds before and after

motor running.

The drive battery is low.

Battery capacity is less than

or equal to 5%.

Charge the battery.

2.4.2.Readjusting the end limits

CAUTION

Control point must be paired to the motorised product.

NOTICE

Orange LED blinks slowly until the new end limit is recorded.

2.4.2.1.Readjusting the upper end limit

1] Briefly press the Up button, to move the

motorised product to the upper end limit.

2] Press and hold the Up and Down buttons

simultaneously until the motorised

product briefly moves up and down.

3] Press and hold the Up or Down button to

move the motorised product to the new

desired position.

4] To confirm the new position press and

hold the my button until the motorised

product briefly moves up and down and

green LED blinks 5 times.

1] 2]

3] 4]

EN Roll Up 28 WF RTS II

2.4.2.2.Readjusting the lower end limit

1] Briefly press the Down button to move

the motorised product to the lower end

limit.

2] Press and hold the Up and Down buttons

simultaneously until the motorised

product briefly moves up and down.

3] Press and hold the Up or Down button to

move the motorised product to the new

desired position.

4] To confirm the new position press and

hold the my button until the motorised

product moves up and down and green

LED blinks 5 times.

1]

3]

2]

4]

2.4.3.Modifying the drive rotation direction

1] Using the Up or Down button on the

control point, move the motorised

product away from the end limits.

2] Press and hold the Up and Down buttons

simultaneously until the motorised

product briefly moves up and down and

orange LED starts to blink slowly.

3] Press the my button until the motorised

product briefly moves up and down to

reverse the rotation direction and green

LED blinks 5 times.

4] Press the Up button to check the new

rotation direction. The drive rotation

direction is reversed.

1]

3]

2]

4]

Roll Up 28 WF RTS II EN

2.4.4.Modifying the wheel rotation direction

1] Using the Up or Down button on the

control point, move the motorised

product away from the end limits.

2] Press and hold the Up and Down buttons

simultaneously until the motorised

product briefly moves up and down and

orange LED starts to blink slowly.

3] Press the Up, my and Down buttons

simultaneously, until the motorised

product briefly moves up and down, wheel

rotation is reversed and green LED blinks 5

times.

1]

2] 3]

2.4.5.Erasing control points from memory

To delete all the programmed control points,

press and hold the drive head programming

button until the motorised product briefly moves

up and down twice.

→ All programmed control points are deleted and

orange LED blinks 5 times every 10 seconds.

2x

2.4.6.Erasing the memory of the drive (factory default)

To reset the drive, press and hold the drive head

programming button until the motorised product

briefly moves up and down 3 times.

 All the settings are erased. Green LED blinks 5

times then orange LED is fixed on.

3x

3.USE AND MAINTENANCE

NOTICE

This drive does not require any maintenance operations.

3.1.Mode selection: Roller or Tilting Mode

The drives are designed to work in 2 modes: Tilting mode or Roller mode.

EN Roll Up 28 WF RTS II

This feature allows the drive to be set according to the type of application.

NOTICE

The drive is set (by default) to work in Roller mode.

1] Move the motorised product away from

the end limits.

2] Simultaneously press and hold the Up and

Down buttons until the motorised

product briefly moves up and down.

3] Press and hold the my and Down buttons

simultaneously until the motorised

product briefly moves up and down to

change from Roller mode to Tilting mode.

g

Green LED blinks twice to indicate that

the drive is in Roller mode or three

times to indicate that the motor is in

Tilting mode.

1]

2] 3]

3.2.Controlling Up, Down, my: in Roller mode

1] To move the motorised product from a

limit to the other limit, briefly press the Up

or Down button.

2] To stop the motorised product, briefly

press the my button.

3] If a favourite position (my) is recorded: To

move the motorised product to the

favourite position (my), briefly press the

my button.

1]

2] 3]

Roll Up 28 WF RTS II EN

3.3.Controlling Up, Down, my: in Tilting mode

1] To move the motorised product from a

limit to the other limit, briefly press (less

than 0,5s) the Up or Down button.

2] To stop the motorised product, press the

my button.

3] If a favourite position (my) is recorded: To

move the motorised product to the

favourite position (my), briefly press the

my button. The motorised product

automatically moves to the down end limit

(first) then to the favourite position (my).

4] To tilt the slats, press and hold the Up or

Down button until the slats reach the

desired position.

2 s 2 s

1]

2]

4]

3]

3.4.Favourite position (my)

NOTICE

An intermediate stop, which is called the “favourite (my) position”, is different

from the upper and lower positions.

3.4.1.Programming or modifying the favourite (my) position

1] Move the motorised product to the

desired favourite position using the Up or

Down button.

2] Briefly press the my button to stop the

motorised product.

3] Press and hold the my button until the

motorised product briefly moves up and

down:

g

The desired favourite (my) position is

programmed and green LED blinks 5

times.

1]

2] 3]

EN Roll Up 28 WF RTS II

NOTICE

Only one favourite (my) position is permitted.

3.4.2.Deleting the favourite position (my)

1] Press the my button:

ð

The motorised product starts to move

and stops in the favourite position

(my).

2] Press and hold the my button until the

motorised product briefly moves up and

down:

g

The favourite position (my) is deleted

and green LED blinks 5 times.

1]

2]

3.5.Adjusting the speed

NOTICE

Orange LED blinks slowly in this mode.

1] Move the motorised product away from

the end limits. Press and hold the Up, my

and Down buttons simultaneously, until

the motorised product briefly moves up

and down once.

ð

The motorised product moves up and

down automatically between limits to

validate entering in speed adjustment

mode.

2] To increase the speed, press and hold the

Up button until the motorised product

briefly moves up and down and green LED

blinks 5 times. Repeat as needed.

2]

1]

4]

3]

Roll Up 28 WF RTS II EN

NOTICE

Maximum speed is reached when the

motorised product moves briefly 3 times in one

direction and 3 times in the other direction.

Red LED blinks 3 times and 3 times

intermittently.

3] To decrease the speed, press and hold the

Down button until the motorised product

briefly moves up and down. Repeat as

needed.

NOTICE

Minimum speed is reached when the motorised

product moves briefly 3 times in one direction

and 3 times in the other direction.

4] To confirm the new speed, press and hold

the my button until the motorised product

briefly moves up and down and green LED

blinks 5 times.

3.6.Tips and advice on operation

3.6.1.Questions about the product?

Observations Possible causes Solutions

The motorised product

does not operate.

The control point battery is

low. LED doesn't light

when any button of a

paired control point is

pressed.

Change control point

battery as required.

Drive battery is low and

requires charge.

Charge the battery.

EN Roll Up 28 WF RTS II

Observations Possible causes Solutions

Thermal protection of the

drive is on (Red LED blinks

slowly).

Wait for the drive to cool

down (Red LED will stop

blinking when drive is ready

to use).

The motorised product

stops before its end limit.

The drive has detected an

obstacle (solid Red LED).

Move the motorised

product in the other

direction.

NOTICE

If the motorised product still does not work, contact a drive and home

automation professional.

3.6.2.Adding/Deleting control points

AAA AB BB

NOTICE

Orange LED blinks slowly when adding or deleting a remote control.

3.6.2.1.Using a control point that has been previously programmed to

the motorised product

1] Press and hold the PROG. button (A) on

the programmed control point until the

motorised product briefly moves up and

down.

ð

Green LED blinks 5 times then orange

LED blinks slowly.

2] Briefly press the PROG. button (B) on the

control point to add or delete.

g

Green LED blinks 5 times.

1]

2]

A

B

2 s

PROG.

0.5 s

PROG.

Roll Up 28 WF RTS II EN

3.6.2.2.Using the Programming button on the drive head

1] Press and hold the drive head

programming button until the motorised

product briefly moves up and down.

ð

Green LED blinks 5 times then orange

LED blinks slowly.

2] Briefly press the PROG. button (B) on the

control point to add or delete.

g

Green LED blinks 5 times.

1]

2]

B

0.5 s

PROG.

NOTICE

Other functions are available, for more information, contact your Somfy

representative.

4.TECHNICAL DATA

Power supply 12 Vdc SELV

Frequency bands and maximum

power used

433.050 MHz - 434.790 MHz e.r.p. <10 mW

Torque 1.1 N·m

Speed 10-28 RPM

Electrical insulation III

Minimum distance between

limits

1 turn

Operating temperature 0° to 60°C

Protection rating IP20 (for indoor use only)

Charging temperature 0° to 40°C

Battery type Li-ion

Battery charging time 4.5 hours maximum

Running time 4 minutes

EN Roll Up 28 WF RTS II

Maximum number of

associated control points

12

NOTICE

For additional information on the technical data for this drive contact your

Somfy representative.

Please separate storage cells and batteries from other types of waste and

recycle them via the local collection facility.

We care about our environment. Do not dispose of the appliance with usual

household waste. Give it to an approved collection point for recycling.

SOMFY ACTIVITES SA, 74300 CLUSES FRANCE as manufacturer hereby

declares that the drive covered by these instructions and used as intended

according to these instructions is in compliance with the essential

requirements of the applicable European Directives and in particular of the

Machinery Directive 2006/42/EC, and the Radio Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at

www.somfy.com/ce.

Philippe Geoffroy, Approval manager, acting on behalf of Activity director,

Cluses, 05/2021.

Somfy limited, Yeadon LS19 7ZA UK hereby declares that the drive

covered by these instructions when marked for input voltage 230V~50Hz

and used as intended according to these instructions, is in compliance with

UK legislation of Machinery safety regulations S.I.2008 N°1597 and the

Radio Equipment Regulations S.I. 2017 N°1206. The full text of the UKCA

declaration of conformity is available at www.somfy.co.uk.

Steven MONTGOMERY, Managing Director Somfy Ltd UK & Ireland,

Yeadon, 05/2021.

La pagina si sta caricando...

Somfy ROLL UP 28 WIREFREE Istruzioni per l'uso

Questo manuale è adatto anche per

Somfy ROLL UP 28 WIREFREE Istruzioni per l'uso

in altre lingue

Documenti correlati