BENDIX BW1422 Manuale utente

Marca: BENDIX

Modello: BW1422

Categoria: Compressori d'aria

Tipo: Manuale utente

Questo manuale è adatto anche per

TU-FLO 700 COMPRESSOR

SD-01-335

Bendix

TU-FLO

700 Air Compressor

COMPRESSOR NAMEPLATE

SER

NO.

MANUFACTURED BY

BENDIX

TU-FLO 700

Two methods are employed for cooling the Tu-Flo

700

compressor during operation. The cylinder head is

connected to the engine’s cooling system, while the cylinder

has external fins for efficient air cooling.

All Tu-Flo

700 compressors utilize the engine’s pressurized

oil system to lubricate the internal moving parts. A nameplate

is attached to the crankcase to identify the compressor.

The nameplate displays a Bendix piece number or in some

cases an engine or vehicle manufacturer’s piece number,

along with a serial number.

DESCRIPTION

The function of the air compressor is to provide and main-

tain air under pressure to operate devices in the air brake

and/or auxiliary air systems

The Tu-Flo

700 compressor is a two cylinder, single stage,

reciprocating compressor with a rated displacement of 15.5

cubic feet of air per minute at 1250 R.P.M. The Tu-Flo

700

compressor is constructed from three major assemblies,

the head, the cylinder block and the crankcase.

The head houses the discharge valving and is installed on

the upper portion of the cylinder block. The cylinder block

contains the cylinder bores and inlet valves and is mounted

to the crankcase. The crankcase houses the crankshaft

and main bearings.

Various mounting and drive configurations, required by the

numerous vehicle engine designs, are available. Two

governor mounting pads are located on either side of the

cylinder block to provide convenient governor mounting.

EXTERIOR

BENDIX

TU-FLO

700 AIR COMPRESSOR

(CROSS SECTION)

CRANKCASE

DISCHARGE

CAP NUT

PISTON

RINGS

CRANKSHAFT

CONNECTING

ROD

DISCHARGE

VALVE

SPRING

INLET

VALVE

SPRING

INLET

VALVE

DISCHARGE

VALVE

DISCHARGE

VALVE SEAT

UNLOADER

MECHANISM

OPERATION

The compressor is driven by the vehicle engine and is

operating continuously while the engine is running. Actual

compression of air is controlled by the compressor unloading

mechanism and the governor. The governor is generally

mounted on the compressor and maintains the brake system

air pressure to a preset maximum and minimum pressure

level.

INTAKE AND COMPRESSION OF AIR (LOADED)

During the down stroke of the piston, a slight vacuum is

created between the ton of the piston and the head, causing

the flat circular inlet valve to move up and off its seat. (Note

the flat square discharge valve remains on its seat.)

Atmospheric air is drawn through the air strainer by the open

inlet valve and into the cylinder (see Fig. 2). As the piston

begins its upward stroke, the air that was drawn into the

cylinder on the down stroke is being compressed. Air

pressure on top of the inlet valve plus the force of its spring,

returns the inlet valve to its seat. The piston continues the

upward stroke and compressed air then flows by the open

discharge valve, into the discharge line and on to the

reservoirs (see Fig. 3). As the piston reaches the top of its

stroke and starts down, the discharge valve spring and air

pressure in the discharge line returns the discharge valve to

its seat. This prevents the compressed air in the discharge

line from returning to the cylinder bore as the intake and

compression cycle is repeated.

NON-COMPRESSION OF AIR (UNLOADED)

When air pressure in the reservoir reaches the cut-out setting

of the governor, the governor allows air to pass from the

reservoir into the cavity beneath the unloader pistons. This

lifts the unloader pistons and plungers. The plungers move

up and hold the inlet valves off their seats (see Figure 4).

With the inlet valves held off their seats by the unloader

pistons and plungers, air is pumped back and forth between

the two cylinders. When air is used from the reservoir and

the pressure drops to the cut-in setting of the governor, the

governor closes and exhausts the air from beneath the

unloader pistons. The unloader saddle spring forces the

saddle, pistons and plungers down and the inlet valves return

to their seats. Compression is then resumed.

COMPRESSOR & THE AIR BRAKE SYSTEM

GENERAL

The compressor is part of the total air brake system, more

specifically, the charging portion of the air brake system. As

a component in the overall system its condition, duty cycle,

proper installation and operation will directly affect other

components in the system.

the air pressure for the air brake system. The air compressor

is typically cooled by the engine coolant system, lubricated

by the engine oil supply and has its inlet connected to the

engine induction system.

As the atmospheric air is compressed, all the water vapor

originally in the air is carried along into the air system, as

well as a small amount of the lubricating oil as vapor. If an

air dryer is not used to remove these contaminants prior to

entering the air system, the majority, but not all, will condense

in the reservoirs. The quantity of contaminants that reach

the air system depends on several factors including

MACK

"FOXHEAD"

CUMMINS

DETROIT

DIESEL

VARIOUS COMPRESSOR MOUNTINGS

installation, maintenance and contaminant handling devices

in the system. These contaminants must either be eliminated

prior to entering the air system or after they enter.

DUTY CYCLE

The duty cycle is the ratio of time the compressor spends

building air to the total engine running time. Air compressors

are designed to build air (run "loaded") up to 25% of the

time. Higher duty cycles cause conditions that affect air

brake charging system performance which may require

additional maintenance. Factors that add to the duty cycle

are: air suspension, additional air accessories, use of an

undersized compressor, frequent stops, excessive leakage

from fittings, connections, lines, chambers or valves, etc.

Refer to Table A in the Troubleshooting section for a guide to

various duty cycles and the consideration that must be given

to maintenance of other components.

COMPRESSOR INSTALLATION

While the original compressor installation is usually

completed by the vehicle manufacturer, conditions of

operation and maintenance may require additional

consideration. The following presents base guidelines.

DISCHARGE LINE

The discharge line allows the air, water-vapor and oil-vapor

mixture to cool between the compressor and air dryer or

reservoir. The typical size of a vehicle's discharge line, (see

column 2 of Table A in the Troubleshooting section) assumes

a compressor with a normal (less than 25%) duty cycle,

operating in a temperate climate. See Bendix and/or other

air dryer manufacturer guidelines as needed.

The discharge line must maintain a constant slope down

from the compressor to the air dryer inlet fitting or reservoir

to avoid low points where ice may form and block the flow. If,

instead, ice blockages occur at the air dryer or reservoir

inlet, insulation may be added here, or if the inlet fitting is a

typical 90 degree fitting, it may be changed to a straight or

45 degree fitting. Shorter discharge line lengths or insulation

may be required in cold climates.

While not all compressors and charging systems are

equipped with a discharge line safety valve this component

is recommended. The discharge line safety valve is installed

in the cylinder head (Tu-Flo

550/750) or close to the

compressor discharge port and protects against over

pressurizing the compressor in the event of a discharge line

freezeup.

FIGURE 1A - SYSTEM DRAWING

Air Dryer

Reservoir Drain

Service Reservoir

(Supply Reservoir)

Compressor

Governor

(Governor plus Synchro valve

for the Bendix

DuraFlo

™

596

Compressor)

Discharge

Line

Optional “Ping” Tank

Optional Bendix

PuraGuard

™

Oil Coalescing Filter

The Air Brake Charging System supplies the

compressed air for the braking system as well as other air

accessories for the vehicle. The system usually consists

of an air compressor, governor, discharge line, air dryer,

and service reservoir.

FIGURE 1B - DISCHARGE LINE SAFETY VALVE

HOLE

THREAD

DISCHARGE LINE TEMPERATURE

When the temperature of the compressed air that enters

the air dryer is within the normal range, the air dryer can

remove most of the charging system oil. If the temperature

of the compressed air is above the normal range, oil as oil-

vapor is able to pass through the air dryer and into the air

system. Larger diameter discharge lines and/or longer

discharge line lengths can help reduce the temperature.

The air dryer contains a filter that collects oil droplets, and a

desiccant bed that removes almost all of the remaining water

vapor. The compressed air is then passed to the air brake

service (supply) reservoir. The oil droplets and the water

collected are automatically purged when the governor

reaches its "cut-out" setting.

For vehicles with accessories that are sensitive to small

amounts of oil, we recommend installation of a Bendix

PuraGuard

™

oil coalescing filter, designed to minimize

the amount of oil present.

LUBRICATION

Since all Tu-Flo

700 compressors are connected to the

engine’s pressurized oil system, a continuous flow of oil is

provided to the compressor, which is eventually returned to

the engine. Oil is fed into the compressor in various ways,

for example: through the rear end cover, the drive end of the

crankshaft or through the front flange adapter. An oil passage

in the crankshaft conducts pressurized oil to the precision

sleeve main bearings and to the connecting rod bearings.

Splash lubrication of the cylinder bores, connecting rod wrist

pin bushings, and the ball type main bearings, on some

models, is obtained as oil is forced out around the crankshaft

journals by engine oil pressure.

Check the exterior of the compressor for the presence of oil

seepage and refer to the TROUBLESHOOTING section for

appropriate tests and corrective action.

OIL PASSING

All reciprocating compressors currently manufactured will

pass a minimal amount of oil. Air dryers will remove the

majority of oil prior to entrance into the air brake system.

For particularly oil sensitive systems the Bendix

PuraGuard

™

oil coalescing filter can be used in conjunction with a

Bendix air dryer.

If compressor oil passing is suspected, refer to the

TROUBLESHOOTING section and TABLE A for the

symptoms and corrective action to be taken. In addition,

Bendix has developed the "Bendix Air System Inspection

Cup" or BASIC test to help substantiate suspected excessive

oil passing. The steps to be followed when using the BASIC

test are presented in APPENDIX A at the end of the

TROUBLESHOOTING section.

FIGURE 2 - INTAKE

INTAKE

STRAINER

STROKE

TO RESERVOIR

INLET VALVE

UNLOADER

PLUNGER

TO GOVERNOR

INTAKE

STRAINER

STROKE

TO RESERVOIR

TO GOVERNOR

PISTON

DISCHARGE

VALVE

UNLOADER

PLUNGER

STROKE

INLET VALVE

TO RESERVOIR

UNLOADER

PLUNGER

INTAKE

STRAINER

TO GOVERNOR

PISTON

DISCHARGE

VALVE

DISCHARGE

VALVE

INLET VALVE

FIGURE 3 - COMPRESSION

FIGURE 4 - UNLOADING

PISTON

DRY ELEMENT—PLEATED PAPER AIR

STRAINER

Every 20,000 miles or 800 operating hours:

Remove the spring clips from either side of mounting baffle

and remove the cover. Replace the pleated paper filter and

remount the cleaned cover making sure the filter is in

position. Be sure to replace the air strainer gasket if the

entire air strainer is removed from the compressor intake.

(Note: Some compressors are fitted with compressor intake

adapters which allow the compressor intake to be connected

to the engine air cleaner.) In this case, the compressor

receives a supply of clean air from the engine air cleaner.

When the engine air filter is changed, the compressor intake

adapter should be checked. If it is loose, remove the intake

adapter, clean the strainer plate, if applicable, and replace

the intake adapter gasket, and reinstall the adapter securely.

Check line connections both at the compressor intake

adapter and at the engine air cleaner. Inspect the connecting

line for ruptures and replace it if necessary.

COOLING

Air flowing through the engine compartment from the action

of the engine’s fan and the movement of the vehicle assists

in cooling the crankcase. Coolant flowing from the engine’s

cooling system through connecting lines enters the

compressor and flows through the internal passages in the

cylinder block and head and back to the engine. Proper

cooling is important in maintaining discharge air temperatures

below the 400°F recommended maximum.

PREVENTIVE MAINTENANCE

Regularly scheduled maintenance is the single most

important factor in maintaining the air brake charging system.

Refer to Table A in the Troubleshooting section for a guide to

various considerations that must be given to the maintenance

of the compressor and other related charging system

components.

Important Note: Review the warranty policy before

performing any intrusive maintenance procedures. An

extended warranty may be voided if intrusive maintenance

is performed during this period.

Every month, 300 operating hours or after each 10,000 miles,

depending on the operating conditions, experience and the

type of strainer used, service the air strainer.

POLYURETHANE SPONGE STRAINER

Every 5000 miles or 150 operating hours:

Remove and wash all of the parts. The strainer element

should be cleaned or replaced. If the element is cleaned, it

should be washed in a commercial solvent or a detergent

and water solution. The element should be saturated in clean

engine oil, then squeezed dry before replacing it in the

strainer. Be sure to replace the air strainer gasket if the

entire air strainer is removed from the compressor intake.

FIGURE 5 - POLYURETHANE SPONGE STRAINER

FIGURE 6 - PAPER AIR STRAINER DRY ELEMENT-

PLEATED

FIGURE 7 - COMPRESSOR INTAKE ADAPTER

Every 6 months, 1800 operating hours or after each

50,000 miles:

Remove the discharge head fittings and inspect the

compressor discharge port and discharge line for excessive

carbon deposits. If excessive buildup is noted in either, the

discharge line must be cleaned or replaced and the

compressor checked more thoroughly, paying special

attention to the air induction system, oil supply and return

system, and proper cooling. If necessary, repair or replace

the compressor. Check for proper belt and pulley alignment

and belt tension. Adjust if necessary, paying special attention

not to over tighten the belt tension. Check for noisy

compressor operation, which could indicate a worn drive

gear coupling or a loose pulley. Adjust and/or replace as

necessary. Check all compressor mounting bolts and

retighten evenly if necessary. Check for leakage and proper

unloader mechanism operation. Replace if defective in any

way.

Every 24 months, 7200 operating hours or after each

200,000 miles:

Perform a thorough inspection as indicated below and

depending upon the results of this inspection or experience,

disassemble the compressor, clean and inspect all parts

thoroughly, repair or replace all worn or damaged parts using

only genuine Bendix replacements or replace the

compressor with a genuine Bendix remanufactured unit.

Important: Should it be necessary to drain the engine cooling

system to prevent damage from freezing, the cylinder head

of the compressor must also be drained.

GENERAL SERVICE CHECKS

INSPECTION

It is of the utmost importance that the compressor receives

a clean supply of air. The air strainer must be properly

installed and kept clean. If the compressor intake is connected

to the engine air cleaner, supercharger, etc., these

connections must be properly installed and maintained.

Check the compressor mountings to be sure they are secure.

Check the drive for proper alignment, belt tension, etc.

Inspect the oil supply and return lines. Be sure these lines

are properly installed and that the compressor is getting the

proper supply of oil, and just as important, that the oil is

returning to the engine. Check the coolant lines to and from

the compressor and see that the cooling fins on the

crankcase are not clogged with dirt, grease, etc. Check the

unloader mechanism for proper and prompt operation.

OPERATING TESTS

Vehicles manufactured after the effective date of FMVSS

121, with the minimum required reservoir volume, must have

a compressor capable of raising air system pressure from

85-100 P.S.I. in 25 seconds or less. This test is performed

with the engine operating at maximum governed speed. The

vehicle manufacturer must certify this performance on new

vehicles with appropriate allowances for air systems with

greater than the minimum required reservoir volume.

AIR LEAKAGE TESTS

Leakage past the discharge valves can be detected by

removing the discharge line, applying shop air back through

the discharge port and listening for escaping air. Also, the

discharge valves and the unloader pistons can be checked

for leakage by building up the air system until the governor

cuts out, then stopping the engine. With the engine stopped,

listen for escaping air at the compressor intake. To pinpoint

leakage if noted, apply a small quantity of oil around the

unloader pistons. If there is no noticeable leakage at the

unloader pistons, the discharge valves may be leaking. If

the compressor does not function as described above, or

leakage is excessive, it is recommended that it be returned

to the nearest authorized Bendix Distributor for a factory

remanufactured compressor. If this is not possible, the

compressor can be repaired using genuine Bendix

replacement parts, in which case, the following information

should prove helpful.

REMOVING AND DISASSEMBLY

REMOVING

These instructions are general and are intended to be a

guide, in some cases additional preparations and precautions

are necessary. Chock the wheels of the vehicle and drain

the air pressure from all the reservoirs in the system. Drain

the engine cooling system and the cylinder head of the

compressor. Disconnect all air, water and oil lines leading

to and from the compressor. Remove the drive gear(s) or

pulley from the compressor crankshaft using a gear puller.

Inspect the pulley or gear and associated parts for visible

wear or damage. Since these parts are precision fitted, they

must be replaced if they are worn or damaged.

DISASSEMBLY

GENERAL

Remove road dirt and grease from the exterior of the

compressor with a cleaning solvent. Before the compressor

is disassembled, the following items should be marked to

show their relationship when the compressor is assembled.

Mark both the front and rear end cover in relation to the

crankcase. Mark the drive end of the crankshaft in relation

to the front end cover and the crankcase. Mark the cylinder

head in relation to the block and the block in relation to the

crankcase. Mark the base plate or base adapter in relation

to the crankcase.

A convenient method to indicate the above relationship is to

use a metal scribe to mark the parts with numbers or lines.

Do not use a marking method that can be wiped off or

obliterated during rebuilding, such as chalk. Remove all

compressor attachments such as governors, air strainers

or inlet fittings, discharge fittings and pipe plugs.

CYLINDER HEAD

Remove the six cylinder head cap screws (1) and tap the

head with a soft mallet to break the gasket seal. Remove

the inlet valve springs (2) and spring inserts (35) from the

head and inlet valves (3) from their guides in the block.

Remove inlet valve guides (4) from around the inlet valve

seats (34) on the block taking care not to damage seats.

Scrape off any gasket material (5) from the cylinder head

and block. Unscrew the discharge valve seats (6) from the

head and remove the discharge valves (7) and springs (8).

Inspect the discharge valve seats (2) for nicks, cracks, and

excessive wear and replace if necessary. The discharge valve

cap/nut stops (9) should be inspected for wear and replaced

if excessive peening has occurred. To determine if excessive

peening has occurred, measure the discharge valve travel.

Discharge valve travel must not exceed .046 inches. If

discharge valve travel is excessive, replace the cap nut/stop

assembly, discharge valve and spring.

Discard the inlet valves (3) and springs (2), the discharge

valves (7), springs (8) and the discharge valve seats (6) if

defective.

CRANKCASE BASE PLATE OR ADAPTER

Remove the cap screws securing the base plate or base

adapter. Tap with soft mallet to break the gasket seal (11).

Scrape off any gasket material from crankcase and plate or

adapter.

CONNECTING ROD ASSEMBLIES

(Note: Before removing the connecting rods, mark each

connecting rod and its cap. Each connecting rod is matched

to its own cap for proper bearing fit, and these parts must

not be interchanged.) Remove the connecting rod bolts (13)

and bearing caps (14). Push the piston (15) with the

connecting rods (16) attached out the top of the cylinders of

the cylinder block. Replace the bearing caps (14) on their

respective connecting rods. Remove the piston rings from

the pistons. If the pistons are to be removed from the

connecting rods, remove the teflon plugs (36) and press the

wrist pins (37) from the pistons and connecting rods.

FIGURE 8 - TU-FLO

700 AIR COMPRESSOR (THRU DRIVE) EXPLODED VIEW

REAR COVER

CYLINDER BLOCK

CRANKSHAFT

FLANGE

ADAPTER

REAR COVER

GASKET

27 22

CYLINDER HEAD

CRANKCASE

If the pistons are removed from the rod, inspect the bronze

wrist pin bushing. Press out and replace the bushing if it is

excessively worn. (See inspection of parts) Discard the piston

rings (18-20) and the connecting rod journal bearings (17).

Discard the wrist pin bushings (21) if they were removed.

CYLINDER BLOCK

If the compressor is fitted with an air strainer, inlet elbow or

governor remove the same.

Remove cap screws (23) securing cylinder block to the

crankcase; separate the crankcase and cylinder block and

scrape off any gasket material.

Remove the unloader spring (34), spring saddle (35), and

spring seat (36) from the inlet cavity of the crankcase, using

long nose pliers. With the use of shop air blow the unloader

plungers (37) and guides (33) out of the cylinder block.

The inlet valve seats can be removed if worn or damaged

and are being replaced. Unloader bore bushings should be

inspected but not removed unless they are damaged. If

bushings are to be replaced, they can be removed by running

a 1/8" pipe threaded rod and pulling the bushing straight up

and out. Do not use "easy out" for removing the bushings.

CRANKCASE

Remove the key (22) or keys from the crankshaft and any

burrs on the crankshaft where the key or keys were removed.

(Note: Through drive compressors may have a crankshaft

key at both ends.) Remove the four cap screws (23) securing

front or drive-end end cover or flange adapter. Remove the

end cover, taking care not to damage the crankshaft oil seal

(27) or front main bearing (26), if any. Remove the o-ring (24)

from around the front end cover. Remove the four cap screws

(30) securing the rear end cover and remove the rear end

cover taking care not to damage the rear main bearing (29),

if any. Remove the o-ring (31) from around the end cover. If

the compressor has ball type main bearings, press the

crankshaft and ball bearings from the crankcase, then press

the ball bearings from the crankshaft.

CLEANING OF PARTS

GENERAL

All parts should be cleaned in a good commercial grade

solvent and dried prior to inspection.

CYLINDER HEAD

Remove all the carbon deposits from the discharge cavities

and all the rust and scale from the cooling cavities of the

cylinder head body. Scrape all the foreign matter from the

body surfaces and use shop air pressure to blow the dirt

particles from all the cavities.

CYLINDER BLOCK

Clean the carbon and dirt from the inlet and unloader

passages. Use shop air pressure to blow the carbon and

dirt deposits from the unloader passages.

OIL PASSAGES

Thoroughly clean all oil passages through the crankshaft,

crankcase, end covers, and base plate or base adapter.

Inspect the passages with a wire to be sure. Blow the

loosened foreign matter out with air pressure.

INSPECTION OF PARTS

CYLINDER HEAD BODY

Inspect the cylinder head for cracks or damage. Apply shop

air pressure to one of the coolant ports with all others

plugged, and check for leakage by applying a soap solution

to the exterior of the body. If leakage is detected, replace

the head.

END COVERS

Check for cracks and external damage. If the crankshaft

main bearings are installed in the end cover, check for

excessive wear and flat spots and replace them if necessary.

If the compressor has an oil seal in the end cover, it should

be removed by pressing it out of the end cover.

CRANKCASE

Check all crankcase surfaces for cracks and damage. On

compressors where ball bearing main bearings are used the

difference between the O.D. of the outer race and the I.D. Of

the crankcase hole should be .0000 in. to .0015 in. loose.

This is to maintain the correct press fit. The crankcase must

be replaced if the fit is too loose.

On compressors fitted with precision, sleeve main bearings,

the difference between the O.D. of the crankshaft journal

and the main bearing I.D. must not exceed .0065 in. If the

clearance is greater than .0065 in., the end cover or main

bearing must be replaced.

CYLINDER BLOCK

Check the unloader bore bushings to be sure they are not

worn, rusted, or damaged. If these bushings are to be

replaced, they can be removed by running a 1/8 in. pipe

thread tap into the bushing, and inserting a 1/8 in. pipe

threaded rod and pulling the bushing straight up and out. Do

not use an easy-out for removing these bushings. If the inlet

valve seats are worn or damaged, so they cannot be

reclaimed by facing, they should be replaced. Cylinder bores

should be checked with inside micrometers or calipers (see

Figure 9). Cylinder bores which are scored or out of round

by more than .001 in. or tapered more than .002 in. should

CRANKSHAFT

Check the crankshaft threads, keyways, tapered ends and

all machined and ground surfaces for wear, scores, or

damage. Standard crankshaft journals are 1.1250 in.- 1.1242

in. in diameter. If the crankshaft journals are excessively

scored or worn or out of round and cannot be reground, the

crankshaft must be replaced. Connecting rod bearing inserts

are available in .010 in., .020 in. and .030 in. undersizes for

compressors with reground crankshafts. Main bearing

journals must be maintained so the ball bearings are a snug

fit or so that no more than .0065 in. clearance exists between

the precision sleeve main bearing and the main bearing

journals on the crankshaft. In crankshafts fitted with oil seal

rings, the oil seal ring groove or grooves must not be worn.

The ring groove walls must have a good finish and they must

be square. Check to be sure the oil passages are open

through the crankshaft.

CONNECTING ROD BEARINGS

Used bearing inserts must be replaced. Connecting rod caps

are not interchangeable. The locking slots of the connecting

rod and cap should be positioned adjacent to each other.

Clearance between the connecting journal and the

connecting rod bearing must not be less than .0003 in. or

more than .0021 in. after rebuilding.

be rebored or honed oversize. Oversized pistons and piston

rings are available in .010 in., .020 in. and .030 in. oversizes.

Cylinder bores must be smooth, straight, and round.

Clearance between the cast iron pistons and cylinder bores

should be between .002 in. minimum and .004 in. maximum.

FIGURE 9 - MEASURING CYLINDER BORES

FIGURE 10 - CORRECT GROOVE CLEARANCE

.002"

.010"

END GAP

.000

.006

OIL RING

.002

.004

OIL RING

STANDARD

PISTON

RING

OIL RING

PISTON

RINGS

PISTON

RING

EXPANDER

RING

PISTONS

Check the pistons for scores, cracks, or enlarged ring

grooves; replace the pistons if any of these conditions are

found. Measure each piston with a micrometer in relation to

the cylinder bore diameter to be sure the diametral clearance

is between .002 in. minimum and .004 in. maximum.

Check the fit of the wrist pins to the pistons and connecting

rod bushings. The wrist pin should be a light press fit in the

piston. If the wrist pin is a loose fit, the piston and pin

assembly should be replaced. Check the fit of the wrist pin

in the connecting rod bushing by rocking the piston. This

clearance should not exceed .0007 in. Replace the wrist pin

bushings if excessive clearance is found. Wrist pin bushings

should be reamed to between .5314 in. and .5317 in. after

being pressed into the connecting rods.

Check the fit of the piston rings in the piston ring grooves.

Check the ring gap with the rings installed in the cylinder

bores. Refer to Figure 10 for correct gap and groove

clearances.

REPAIRS

DISCHARGE VALVES, VALVE STOPS AND

SEATS

If the discharge valve seats merely show signs of slight wear,

they can be dressed by using a lapping stone, grinding

compound and grinding tool. Install the new discharge valve

springs and valves. Screw in the discharge valve seats.

Discharge valve travel should be between .030 in. to .046 in.

To test for leakage by the discharge valves, apply 100 pounds

of air pressure through the cylinder head discharge port and

apply a soap solution to the discharge valves and seats. A

slight leakage in the form of soap bubbles is permissible. If

excessive leakage is found, leave the air pressure applied

and with the use of a fiber or hardwood dowel and a hammer,

tap the discharge valves off their seats several times. This

will help the valves to seat and should reduce the leakage.

With the air pressure still applied at the discharge port of

the cylinder head, check for leakage around the discharge

valve cap nut on the top of the cylinder head casting. No

leakage is permitted.

INLET VALVES AND SEATS

Inlet valves and springs should be replaced, if the inlet valve

seats show signs of slight nicks or scratches. They can be

redressed with a fine piece of emery cloth or by lapping with

a lapping stone, grinding compound and grinding tool. If the

seats are damaged to the extent that they cannot be

reclaimed, they must be replaced. The dimension from the

top of the cylinder block to the inlet valve seat should not

exceed .113 in. nor be less than .101 in.

ASSEMBLY

General Note: All torques specified in this manual are

assembly torques and can be expected to fall off after

assembly is accomplished. Do not retorque after initial

assembly torques fall.

To convert inch pounds of torque to foot pounds of torque,

divide inch pounds by 12.

inch pounds ÷ 12 = foot pounds

To convert foot pounds of torque to inch pounds of torque,

multiply foot pounds by 12.

foot pounds x 12 = inch pounds

INSTALLING THE CRANKSHAFT

Press new sleeve bearings in the end cover and crankcase.

Ensure that the slot in the bearings line up with the oil

passages in the end cover or crankcase. If you have a model

with no oil passage present in the crankcase, press the

sleeve bearing into the crankcase with the slot located 90

degrees from vertical.

Install the front thrust washer with the tang inserted in the

slot toward the flange. Insert the crankshaft and the rear

thrust washer with the tang toward the rear of the compressor.

Place the oil seal ring on the boss of the rear end cover and

install the end cover making sure not to pinch the seal ring.

Ensure the tang of the thrust washer is inserted in the slot

of the end cover. Fasten the end cover to the crankcase with

the four cover cap screws. Torque the cap screws to 175-

225 inch pounds in a cross pattern. Note: For cast iron

flange adapters, torque the four 7/16 in. cap screws to 38-

45 foot pounds. For die cast aluminum end covers, torque

the four 7/16 in. cap screws to 25-30 foot pounds. All end

covers using 5/16 in. cap screws or stud and nuts are torqued

to 15-18 foot pounds. For through drive compressors with a

cast iron end cover, torque the four 7/16 in. cap screws to

25-30 foot pounds.

PISTONS AND CONNECTING RODS

If new wrist pin bushings are to be used, they should be

pressed into the connecting rods so that the oil hole in the

bushing lines up with the one in the rod. The new bushings

should then be reamed or honed to provide between .0001

in. (.00254 mm) and .0006 in. (.01524 mm) clearance on

the wrist pin. Position the connecting rod in the piston and

press in the wrist pin.

Pistons installed in compressors manufactured prior to

November, 1976, will have the wrist pin secured in the piston

by a lock wire extending through matching holes in wrist pin

and piston boss, anchored in a hole in the side wall of the

piston. If the original pistons are used the wrist pin must be

pressed in so the hole in the wrist pin aligns with that of the

FIGURE 11 FIGURE 12

DISCHARGE VALVE,

VALVE STOP

AND SEAT

INLET VALVE

AND SEAT

piston and secure same by inserting the new lockwire

through the hole in piston and wrist pin and lock the wire by

snapping the short 90 section into the lockwire hole in the

bottom of the piston.

Compressors built after November, 1976, will have the wrist

pin secured by Teflon buttons in either end of the wrist pin,

allowing the wrist pin to float. The Teflon buttons pc. no.

292392 may be used with either new or old wrist pins. The

later design pistons have two rings above the wrist pin and

one below. Install the piston rings in the correct location

with the ring pipmarks up. Stagger the position of the ring

gaps. Prelubricate the piston, piston rings, wrist pins and

connecting rod.

CYLINDER BLOCK

Align gasket (12), crankcase and cylinder block and secure

with cap screws (23). Torque to 15-19 foot pounds.

UNLOADER

A new unloader kit should used when rebuilding. (Figure

13). (Piece Number 279615). The unloader pistons in the kit

are prelubricated with a special lubricant piece number

239379 and need no additional lubrication. Install the unloader

pistons (28) in their bores being careful not to cut the

o-rings. Position the unloader plungers (37) in their guides

(38) and slip them in and over the tops of the pistons. Install

the unloader spring seat (36) in the cylinder block inlet cavity;

a small hole is drilled in the cylinder block for this purpose.

Position the saddle (35) between the unloader piston guides

(38), so its forks are centered on the guides. Install the

unloader spring (34), making sure it seats over the spring

seats both in the block and on the saddle. Position and

install the inlet valve guides (38), then drop the inlet valves in

their guides. The inlet valves should be a loose sliding fit in

the guides.

FIGURE 13 - UNLOADER MECHANISM

CYLINDER HEAD

Install the inlet valve springs in the cylinder head by applying

a turning motion to the spring after it is in the head. The

turning motion should dig the spring wire into the spring

seat in the bottom of the spring bore in the head. Should

this procedure fail after repeated attempts, use a very small

quantity of grease to hold them in place, just enough to

keep the springs from falling out. Place the cylinder head

gasket on the cylinder block. Carefully align the cylinder

head assembly on the block and install the cap screws,

tightening them evenly to a torque of 15-19 foot pounds.

BASE PLATE OR BASE ADAPTER

Position the base plate or base adapter gasket on the

crankcase and install the base plate or base adapter as

marked before disassembly. Tighten the six cap screws

securing the cast iron base adapter evenly to a torque of 38-

45 foot pounds, and 12-16 foot pounds for base plate or

aluminum cover.

TESTING REBUILT COMPRESSOR

In order to properly test a compressor under operating

conditions, a test rack for correct mounting, cooling,

lubricating, and driving the compressor is necessary. Such

tests are not compulsory if the unit has been carefully rebuilt

by an experienced person. A compressor efficiency or build-

up test can be run which is not too difficult. An engine

lubricated compressor must be connected to an oil supply

line of at least 15 P.S.I. pressure during the test and an oil

return line must be installed to keep the crankcase drained.

Connect to the compressor discharge port, a reservoir with

a volume of 1500 cubic inches, including the volume of

connecting line. With the compressor operating at 2100

R.P.M., the time required to raise the reservoir(s) pressure

from 85 P.S.I. to 100 P.S.I. should not exceed 7 seconds.

During this test, the compressor should be checked for

gasket leakage and noisy operation, as well as unloader

operation and leakage.

INSPECTION OF REBUILT UNIT

Check to be sure that covers, plugs, or masking tape are

used to protect all ports if compressor is not to be installed

immediately. Fit the end of all crankshafts with keys, nuts,

and cotter pins as required and then protect the ends against

damage by wrapping with masking tape or friction tape. The

open bottom of a vertical engine lubricated compressors

should be protected against the entrance of dirt during

handling or storage, by installing a temporary cover over the

base.

COMPRESSOR TROUBLESHOOTING

IMPORTANT: The troubleshooting contained in this section

considers the compressor as an integrated component of

the overall air brake charging system and assumes that an

air dryer is in use. The troubleshooting presented will cover

not only the compressor itself, but also other charging system

devices as they relate to the compressor.

WARNING! PLEASE READ AND FOLLOW

THESE INSTRUCTIONS TO AVOID

PERSONAL INJURY OR DEATH:

When working on or around a vehicle, the following

general precautions should be observed at all times.

1. Park the vehicle on a level surface, apply the

parking brakes, and always block the wheels.

Always wear safety glasses.

2. Stop the engine and remove ignition key when

working under or around the vehicle. When

working in the engine compartment, the engine

should be shut off and the ignition key should be

removed. Where circumstances require that the

engine be in operation, EXTREME CAUTION should

be used to prevent personal injury resulting from

contact with moving, rotating, leaking, heated or

electrically charged components.

3. Do not attempt to install, remove, disassemble or

assemble a component until you have read and

thoroughly understand the recommended

procedures. Use only the proper tools and observe

all precautions pertaining to use of those tools.

4. If the work is being performed on the vehicle’s air

brake system, or any auxiliary pressurized air

systems, make certain to drain the air pressure

from all reservoirs before beginning ANY work on

the vehicle. If the vehicle is equipped with an

AD-IS

™

air dryer system or a dryer reservoir module,

be sure to drain the purge reservoir.

5. Following the vehicle manufacturer’s

recommended procedures, deactivate the electrical

system in a manner that safely removes all electrical

power from the vehicle.

6. Never exceed manufacturer’s recommended

pressures.

7. Never connect or disconnect a hose or line

containing pressure; it may whip. Never remove a

component or plug unless you are certain all

system pressure has been depleted.

8. Use only genuine Bendix

replacement parts,

components and kits. Replacement hardware,

tubing, hose, fittings, etc. must be of equivalent

size, type and strength as original equipment and

be designed specifically for such applications and

systems.

9. Components with stripped threads or damaged

parts should be replaced rather than repaired. Do

not attempt repairs requiring machining or welding

unless specifically stated and approved by the

vehicle and component manufacturer.

10. Prior to returning the vehicle to service, make

certain all components and systems are restored to

their proper operating condition.

11. For vehicles with Antilock Traction Control (ATC),

the ATC function must be disabled (ATC indicator

lamp should be ON) prior to performing any vehicle

maintenance where one or more wheels on a

drive axle are lifted off the ground and moving.

TABULATED DATA

Number of cylinders ............................ 2

Bore size ............................................ 2.75 in.

Stroke ................................................. 1.81 in.

Piston displacement at 1250 RPM ...... 15.5 cu. ft.

Maximum recommended RPM

(naturally aspirated)............................. 3000

Minimum coolant flow at maximum

RPM ................................................... 2.5 gal./min.

Recommended minimum

discharge line size .............................. 5/8 in. OD

Copper Tube

Recommended minimum oil

return line size .................................... 5/8 in. OD Tubing

Recommended minimum oil

supply line size ................................... 1/4 in. OD Tubing

Recommended minimum unloader

line size .............................................. 1/4 in. OD Tubing

Recommended minimum coolant

line size .............................................. 1/2 in. OD Tubing

Recommended maximum inlet

air temperature .................................... 250°F

Recommended maximum

discharge air temperature .................... 400°F

Minimum pressure required

to unload ............................................. 60 PSI

*This guide is only for vehicles that use desiccant air dryers.

The guide consists of an introduction to air brake charging system

components, a table showing recommended vehicle maintenance

schedules, and a troubleshooting symptom and remedy section with tests

to diagnose most charging system problems.

Advanced Troubleshooting Guide

for Air Brake Compressors

This troubleshooting guide obsoletes and supersedes all previous published

troubleshooting information relative to Bendix air compressors.

Air brake charging system:

Slow build (9.0) . . . . . . . . . . . . . . . . . 21 - 22

Doesn’t build air (10.0) . . . . . . . . . . . . . . . 23

Air dryer:

Doesn’t purge (14.0) . . . . . . . . . . . . . . . . . 24

Safety valve releases air (12.0). . . . . . . . . 24

Compressor:

Constantly cycles (15.0) . . . . . . . . . . . . . . 24

Leaks air (16.0) . . . . . . . . . . . . . . . . . . . . . 25

Safety valve releases air (11.0) . . . . . . . . . 23

Noisy (18.0) . . . . . . . . . . . . . . . . . . . . . . . . 25

Reservoir:

Safety valve releases air (13.0). . . . . . . . . 24

INDEX

Air

Coolant

Engine

Oil

Compressor leaks coolant (17.0) . . . . . . . . . . 25

Oil consumption (6.0) . . . . . . . . . . . . . . . . . . . 21

Oil Test Card results (1.0) . . . . . . . . . . . . . . . . 16

Oil is present:

On the outside of the compressor (2.0). . . 17

At the air dryer purge/exhaust

or surrounding area (3.0) . . . . . . . . . . . 17

In the supply reservoir (4.0). . . . . . . . 18 - 20

At the valves (5.0) . . . . . . . . . . . . . . . . . . . 20

At air dryer cartridge (7.0) . . . . . . . . . . . . . 21

In the ping tank or compressor

discharge aftercooler (8.0) . . . . . . . . . . 21

Symptom Page Number

(1) Oil Leakage at Head Gasket . . .26

(2) System Leakage . . . . . . . . . . . .26

(3) Compressor Discharge and

Air Dryer Inlet Temperature . . . .26

(4) Governor Malfunction . . . . . . . .27

(5) Governor Control Line . . . . . . . .27

(6) Compressor Unloader . . . . . . . .27

BASIC Test Information . . . . . . 28-30

Test Procedures

Maintenance Schedule and

Usage Guidelines (Table A) . . 15

Symptom Page Number

Maintenance & Usage Guidelines

Introduction to the Air Brake Charging System

builds the air pressure for the air brake system. The

air compressor is typically cooled by the engine coolant

system and lubricated by the engine oil supply.

The compressor's unloader mechanism and governor

(along with a synchro valve for the Bendix

DuraFlo

™

596

air compressor) control the brake system air

pressure between a preset maximum and minimum

pressure level by monitoring the pressure in the service

(or “supply”) reservoir. When the air pressure becomes

greater than that of the preset “cut-out”, the governor

controls the unloader mechanism of the compressor

to stop the compressor from building air and also

causes the air dryer to purge. As the service reservoir

air pressure drops to the “cut-in” setting of the governor,

the governor returns the compressor back to building

air and the air dryer to air drying mode.

As the atmospheric air is compressed, all the water

vapor originally in the air is carried along into the air

system, as well as a small amount of the lubricating oil

as vapor.

The duty cycle is the ratio of time the compressor

spends building air to the total engine running time.

Air compressors are designed to build air (run “loaded”)

up to 25% of the time. Higher duty cycles cause

conditions that affect air brake charging system

performance which may require additional

maintenance. Factors that add to the duty cycle are:

air suspension, additional air accessories, use of an

undersized compressor, frequent stops, excessive

leakage from fittings, connections, lines, chambers or

valves, etc.

The discharge line allows the air, water-vapor and

oil-vapor mixture to cool between the compressor and

air dryer. The typical size of a vehicle's discharge line,

(see column 2 of Table A on page 15) assumes a

compressor with a normal (less than 25%) duty cycle,

operating in a temperate climate. See Bendix and/or

other air dryer manufacturer guidelines as needed.

When the temperature of the compressed air that enters

the air dryer is within the normal range, the air dryer can

remove most of the charging system oil. If the

temperature of the compressed air is above the normal

range, oil as oil-vapor is able to pass through the air

dryer and into the air system. Larger diameter discharge

lines and/or longer discharge line lengths can help reduce

the temperature.

The discharge line must maintain a constant slope

down from the compressor to the air dryer inlet fitting

to avoid low points where ice may form and block the

flow. If, instead, ice blockages occur at the air dryer

inlet, insulation may be added here, or if the inlet fitting

is a typical 90 degree fitting, it may be changed to a

straight or 45 degree fitting. For more information on

how to help prevent discharge line freeze-ups, see

Bendix Bulletins TCH-08-21 and TCH-08-22 (see

pages 31-33). Shorter discharge line lengths or

insulation may be required in cold climates.

The air dryer contains a filter that collects oil droplets,

and a desiccant bed that removes almost all of the

remaining water vapor. The compressed air is then

passed to the air brake service (supply) reservoir. The

oil droplets and the water collected are automatically

purged when the governor reaches its “cut-out” setting.

For vehicles with accessories that are sensitive to small

amounts of oil, we recommended installation of a

Bendix

PuraGuard

system filter, designed to minimize

the amount of oil present.

Air Dryer

Reservoir Drain

Service Reservoir

(Supply Reservoir)

Compressor

Governor

(Governor plus Synchro valve

for the Bendix

DuraFlo

™

596

™

Compressor)

Discharge

Line

Optional “Ping” Tank

Optional Bendix

PuraGuard

System Filter or PuraGuard

™

Oil Coalescing Filter

The Air Brake Charging System supplies the

compressed air for the braking system as well as other

air accessories for the vehicle. The system usually

consists of an air compressor, governor, discharge line,

air dryer, and service reservoir.

Compressor with up to 25% duty cycle

Footnotes:

1 With increased air demand the air dryer cartridge needs to be replaced more often.

2 Use the drain valves to slowly drain all reservoirs to zero psi.

3 Allow the oil/water mixture to fully settle before measuring oil quantity.

4 To counter above normal temperatures at the air dryer inlet, (and resultant oil-vapor passing

upstream in the air system) replace the discharge line with one of a larger diameter and/

or longer length. This helps reduce the air's temperature. If sufficient cooling occurs, the

oil-vapor condenses and can be removed by the air dryer. Discharge line upgrades are not

covered under warranty. Note: To help prevent discharge line freeze-ups, shorter discharge

line lengths or insulation may be required in cold climates. (See Bendix Bulletins TCH-08-21

and TCH-08-22, included in Appendix B, for more information.)

5 For certain vehicles/applications, where turbo-charged inlet air is used, a smaller size

compressor may be permissible.

Recom- Recom- Acceptable

Typical Discharge mended mended Reservoir

Compressors Line Air Dryer Reservoir Oil Contents

No. of Spec'd Cartridge Drain at Regular

Axles Replacement

Schedule

Drain Interval

High Air Use

Low Air Use

e.g. Double/triple trailer, open

highway coach/RV, (most)

pick-up & delivery, yard or

terminal jockey, off-highway,

construction, loggers, concrete

mixer, dump truck, fire truck.

e.g. Line haul single trailer

w/o air suspension, air over

hydraulic brakes.

e.g. Line haul single trailer

with air suspension,

school bus.

e.g. City transit bus, refuse,

bulk unloaders, low boys,

urban region coach, central

tire inflation.

less

Table A: Maintenance Schedule and Usage Guidelines

Recom-

mended

Every

Month -

Max of

every 90

days

Every

Month

Every 3

Years

Every 2

Years

Every

Year

I.D.

Vehicle Used for:

Column 1

Column 2 Column 3 Column 4 Column 5

Regularly scheduled maintenance is the single most important factor in maintaining the air brake charging system.

Note: Compressor and/or air dryer

upgrades are recommended in cases

where duty cycle is greater than the

normal range (for the examples

above).

For Bendix

Tu-Flo

550 and 750

compressors, unloader service is

recommended every 250,000 miles.

Length

6 ft.

1/2 in.

9 ft.1/2 in.

12 ft.

1/2 in.

5/8 in.

12 ft.

BASIC test

acceptable

range:

5 oil units

per month.

See

appendix

For oil carry-over

control

suggested

upgrades:

3/4 in. 15 ft.

For oil carry-over

control

suggested

upgrades:

5/8 in. 15 ft.

For oil carry-over

control

suggested

upgrades:

5/8 in. 9 ft.

For oil carry-over

control

suggested

upgrades:

5/8 in. 12 ft.

Compressor with less than 15% duty

cycle

Compressor with up to 25% duty cycle

Bendix

BA-921

™

air compressor

Bendix

Tu-Flo

550 air compressor

Bendix

Tu-Flo

750 air compressor

Bendix

BA-922

™

, or DuraFlo

™

596

air compressor

BASIC test

acceptable

range:

3 oil units

per month.

See

appendix

For the

BASIC

Test Kit:

Order

Bendix

P/N

5013711

Air Brake Charging System Troubleshooting

How to use this guide:

1.0 Oil Test Card

Results

Not a valid test.

Discontinue using this test.

Do not use this card test to diagnose

compressor "oil passing" issues. They are

subjective and error prone. Use only the

Bendix Air System Inspection Cup (BASIC) test

and the methods described in this guide for

advanced troubleshooting.

The Bendix

BASIC test should be the

definitive method for judging excessive oil

fouling/oil passing. (See Appendix A, on

page 28 for a flowchart and expanded

explanation of the checklist used when

conducting the BASIC test.)

Symptom: What it may indicate: What you should do:

Find the symptom(s) that you see, then move to the right to

find the possible causes (“What it may indicate”) and

remedies (“What you should do”).

Review the warranty policy before performing any intrusive

compressor maintenance. Unloader or cylinder head gasket

replacement and resealing of the bottom cover plate are

usually permitted under warranty. Follow all standard safety

procedures when performing any maintenance.

Look for:

Normal - Charging system is working within

normal range.

Check - Charging system needs further

investigation.

Bendix

BASIC Test

WARNING! Please READ and follow these instructions to

avoid personal injury or death:

When working on or around a vehicle, the following general

precautions should be observed at all times.

1. Park the vehicle on a level surface, apply the parking

brakes, and always block the wheels. Always wear safety

glasses.

2. Stop the engine and remove ignition key when working

under or around the vehicle. When working in the engine

compartment, the engine should be shut off and the ignition

key should be removed. Where circumstances require that

the engine be in operation, EXTREME CAUTION should

be used to prevent personal injury resulting from contact

with moving, rotating, leaking, heated or electrically charged

components.

3. Do not attempt to install, remove, disassemble or assemble

a component until you have read and thoroughly

understand the recommended procedures. Use only the

proper tools and observe all precautions pertaining to use

of those tools.

4. If the work is being performed on the vehicle’s air brake

system, or any auxiliary pressurized air systems, make

certain to drain the air pressure from all reservoirs before

beginning ANY work on the vehicle. If the vehicle is

equipped with an AD-IS

™

air dryer system or a dryer

reservoir module, be sure to drain the purge reservoir.

5. Following the vehicle manufacturer’s recommended

procedures, deactivate the electrical system in a manner

that safely removes all electrical power from the vehicle.

6. Never exceed manufacturer’s recommended pressures.

7. Never connect or disconnect a hose or line containing

pressure; it may whip. Never remove a component or plug

unless you are certain all system pressure has been

depleted.

8. Use only genuine Bendix

replacement parts, components

and kits. Replacement hardware, tubing, hose, fittings, etc.

must be of equivalent size, type and strength as original

equipment and be designed specifically for such

applications and systems.

9. Components with stripped threads or damaged parts

should be replaced rather than repaired. Do not attempt

repairs requiring machining or welding unless specifically

stated and approved by the vehicle and component

manufacturer.

10.Prior to returning the vehicle to service, make certain all

components and systems are restored to their proper

operating condition.

11. For vehicles with Antilock Traction Control (ATC), the ATC

function must be disabled (ATC indicator lamp should be

ON) prior to performing any vehicle maintenance where

one or more wheels on a drive axle are lifted off the ground

and moving.

Symptom: What it may indicate: What you should do:

2.2 Oil leaking

from compressor:

(a)Excessive leak at head gasket.

(b)Leak at bottom cover plate.

(c)Leak at internal rear flange gasket.

(d)Leak through crankcase.

(e)(If unable to tell source of leak.)

ð Go to Test 1 on page 26.

ð Reseal bottom cover plate using RTV

silicone sealant.

ð Replace compressor.

ð Clean compressor and check periodically.

Air brake charging system functioning

normally.

ð Air dryers remove water and oil from the

air brake charging system.

Check that regular maintenance is being

performed. Return the vehicle to service.

An optional kit (Bendix piece number

5011327 for the Bendix

AD-IS

™

or AD-IP

™

air dryers, or 5003838 for the Bendix

AD-9

™

air dryer) is available to redirect the

air dryer exhaust.

3.0 Oil at air dryer

purge/exhaust or

surrounding area

(c)

2.0 Oil on the

Outside of the

Compressor

Find the source and repair. Return the vehicle

to service.

ð Repair or replace as necessary. If the

mounting bolt torques are low, replace the

gasket.

ð Replace the fitting gasket. Inspect inlet

hose and replace as necessary.

ð Replace gasket or fitting as necessary to

ensure good seal.

ð Inspect and repair as necessary.

Engine and/or other accessories

leaking onto compressor.

(a)Leak at the front or rear (fuel

pump, etc.) mounting flange.

(b)Leak at air inlet fitting.

(c)Leak at air discharge fitting.

(d)Loose/broken oil line fittings.

2.1 Oil leaking at

compressor / engine

connections:

(a)

Head

gasket

and rear

flange

gasket

locations.

(c)

4.0 Oil in Supply or

Service Reservoir

(air dryer installed)

(If a maintained Bendix

PuraGuard

system filter

or Bendix

PuraGuard

™

oil coalescing filter

is installed, call

1-800-AIR-BRAKE

(1-800-247-2725) and

speak to a Tech Team

member.)

(a)If air brake charging system

maintenance has not been

performed.

That is, reservoir(s) have not been

drained per the schedule in Table

A on page 15, Column 4 and/or the

air dryer maintenance has not

been performed as in Column 3.

(b)If the vehicle maintenance has

been performed as recom-

mended in Table A on page 15,

some oil in the reservoirs is normal.

ð Drain all air tanks and check vehicle at next

service interval using the Bendix

BASIC

test. See Table A on page 15, column 3

and 4, for recommended service schedule.

ð Drain all air tanks into Bendix

BASIC test

cup (Bendix Air System Inspection Cup).

If less than one unit of reservoir contents

is found, the vehicle can be returned to

service. Note: If more than one oil unit

of water (or a cloudy emulsion mixture)

is present, change the vehicle's air

dryer, check for air system leakage (Test

2, on page 26), stop inspection and

check again at the next service interval.

See the BASIC test kit for full details.

If less than one "oil unit" of water (or water/

cloudy emulsion mixture) is present, use

the BASIC cup chart on the label of the

cup to determine if the amount of oil found

is within the acceptable level.

ðIf within the normal range, return the

vehicle to service. For vehicles with

accessories that are sensitive to small

amounts of oil, consider a Bendix

PuraGuard

™

oil coalescing filter.

ð If outside the normal range go to

Symptom 4.0(c).

Also see the Table A on page 15, column

3 for recommended air dryer cartridge

replacement schedule.

Maintenance

(a)

ð Go to

Test 2 on page 26.

ð See Table A, column 1, on page 15 for

recommended compressor sizes.

ð If the compressor is "too small" for

the vehicle's role (for example, where a

vehicle's use has changed or service

conditions exceed the original vehicle or

engine OE spec's) then upgrade the

compressor. Note: The costs incurred (e.g.

installing a larger capacity compressor,

etc.) are not covered under original

compressor warranty.

ð If the compressor is correct for the

vehicle, go to Symptom 4.0 (e).

Duty cycle too high

Symptom: What it may indicate: What you should do:

See Table A, on page 15,

for maintenance

schedule information.

Drain

all air tanks (reservoirs)

into the Bendix

BASIC test

cup. (Bendix kit P/N 5013711).

The duty cycle is the ratio of time the compressor spends

building air to total engine running time. Air compressors

are designed to build air (to "run loaded") up to 25% of the

time. Higher duty cycles cause conditions that affect air

brake charging system performance which may require

additional maintenance. Factors that add to the duty cycle

are: air suspension, additional air accessories, use of an

undersized compressor, frequent stops, excessive leakage

from fittings, connections, lines, chambers or valves, etc.

(c)Air brake system leakage.

(d)Compressor may be undersized for

the application.

Symptom: What it may indicate: What you should do:

(e)Air compressor discharge and/or

air dryer inlet temperature too high.

(f) Insufficient coolant flow.

(g)Restricted discharge line.

ð Check temperature as outlined in Test 3

on page 26. If temperatures are normal

go to 4.0(h).

ð Inspect coolant line. Replace as necessary

(I.D. is 1/2").

ð Inspect the coolant lines for kinks and

restrictions and fittings for restrictions.

Replace as necessary.

ð Verify coolant lines go from engine block

to compressor and back to the water pump.

Repair as necessary.

ð If discharge line is restricted or more than

1/16" carbon build up is found, replace the

discharge line. See Table A, column 2, on

page 15 for recommended size. Replace

as necessary.

ð The discharge line must maintain a

constant slope down from the compressor

to the air dryer inlet fitting to avoid low

points where ice may form and block the

flow. If, instead, ice blockages occur at the

air dryer inlet, insulation may be added

here, or if the inlet fitting is a typical 90

degree fitting, it may be changed to a

straight or 45 degree fitting. For more

information on how to help prevent discharge

line freeze-ups, see Bendix Bulletins

TCH-08-21 and TCH-08-22 (Appendix B).

Shorter discharge line lengths or insulation

may be required in cold climates.

Temperature

Other

ð Check compressor air inlet line for

restrictions, brittleness, soft or sagging

hose conditions etc. Repair as necessary.

Inlet line size is 3/4 ID. Maximum

restriction requirement for compressors is

25 inches of water.

ð Check the engine air filter and service if

necessary (if possible, check the air filter

usage indicator).

(h)Restricted air inlet (not enough air

to compressor).

(g)

(h)

4.0 Oil in Supply

or Service

Reservoir*

(air dryer installed)

(continued)

(f)

(e)

(g)

Kinked discharge line shown.

Partly

collapsed

inlet line

shown.

Testing the temperature

at the discharge fitting.

Inspecting the coolant hoses.

*If a maintained Bendix

PuraGuard

system filter or Bendix

PuraGuard

™

oil coalescing

filter is installed, call 1-800-AIR-BRAKE (1-800-247-2725) and speak to a Tech Team

member.

Symptom: What it may indicate: What you should do:

(i) Poorly filtered inlet air (poor air

quality to compressor).

(j) Governor malfunction or setting.

(k)Compressor malfunction.

4.0 Oil in Supply

or Service

Reservoir*

(air dryer installed)

(continued)

ð Check for leaking, damaged or defective

compressor air inlet components (e.g.

induction line, fittings, gaskets, filter bodies,

etc.). Repair inlet components as needed.

Note: Dirt ingestion will damage

compressor and is not covered under

warranty.

ð Go to Test 4 on page 27.

ð If you found excessive oil present in the

service reservoir in step 4.0 (b) above and

you did not find any issues in steps 4.0 (c)

through 4.0 (j) above, the compressor may

be passing oil.

Replace compressor. If still under

warranty, follow normal warranty process.

Note: After replacing a compressor,

residual oil may take a considerable period

of time to be flushed from the air brake

system.

Other (cont.)

Inspect the

engine air

cleaner.

** SAE J2024 outlines tests all air brake system pneumatic

components need to be able to pass, including minimum

levels of tolerance to contamination.

5.0 Oil present at

valves (e.g. at

exhaust, or seen

during servicing).

Air brake system valves are required

to tolerate a light coating of oil.

ð A small amount of oil does not affect SAE

J2024** compliant valves.

ð Check that regular maintenance is being

performed and that the amount of oil in the

air tanks (reservoirs) is within the

acceptable range shown on the Bendix

BASIC test cup (see also column 5 of Table

A on page 15). Return the vehicle to

service.

For oil-sensitive systems, see page 14.

Genuine

Bendix

valves are

all SAE

J2024

compliant.

*If a maintained Bendix

PuraGuard

system filter or Bendix

PuraGuard

™

oil coalescing

filter is installed, call 1-800-AIR-BRAKE (1-800-247-2725) and speak to a Tech Team

member.

Crankcase Flooding

Consider installing a compressor bottom drain kit

(where available) in cases of chronic oil passing

where all other operating conditions have been

investigated. Bendix compressors are designed to

have a 'dry' sump and the presence of excess oil in

the crankcase can lead to oil carryover.

La pagina sta caricando ...

BENDIX BW1422 Manuale utente

Marca: BENDIX

Modello: BW1422

Categoria: Compressori d'aria

Tipo: Manuale utente

Questo manuale è adatto anche per

TU-FLO 700 COMPRESSOR

Scarica il pdf

rapporto

in altre lingue

English: BENDIX BW1422 User manual

BENDIX BW1422 Manuale utente

Questo manuale è adatto anche per

BENDIX BW1422 Manuale utente

in altre lingue

Altri documenti