Sony CDX-G1301U Manuale del proprietario

4-738-936-22(1)

CDX-G1302U/CDX-G1301U/CDX-G1300U

FM/MW/LW

CD Car Audio

FM/MW/LW

CD Автомобильное Аудио

Operating Instructions

GB

Bedienungsanleitung

DE

Mode d’emploi

FR

Istruzioni per l’uso

IT

Manual de

instrucciones

ES

Инструкция по

эксплуатации

RU

To cancel the demonstration (DEMO) display, see

page 12.

For the connection/installation, see page 21.

Zum Deaktivieren der Demo-Anzeige (DEMO)

schlagen Sie bitte auf Seite 13 nach.

Informationen zum Anschluss und zur Installation

finden Sie auf Seite 24.

Pour annuler la démonstration (DEMO), reportez-

vous à la page 13.

Pour le raccordement/l’installation, reportez-vous à

la page 23.

Per annullare la dimostrazione (DEMO), vedere

pagina 12.

Per l’installazione e i collegamenti, consultare

pagina 23.

Para cancelar la pantalla de demostración (DEMO),

consulte la página 12.

Para la conexión/instalación, consulte la página 23.

Для отмены демонстрации на дисплее (режим

DEMO) см. стр. 13.

Инструкции по установке/подключению см. на

стр. 25.

2GB

Made in Thailand

This product is classified as a Class 1 Laser

product under IEC/EN 60825-1:2007 and IEC/

EN 60825-1:2014.

 Emission Duration: Continuous

 Laser Output: Less than 55.8 W

 Wavelength: 775 nm to 800 nm

The nameplate indicating operating voltage,

etc., is located on the bottom of the chassis.

The validity of the CE marking is restricted to

only those countries where it is legally

enforced, mainly in the countries EEA

(European Economic Area).

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of

conformity is available at the following

internet address:

http://www.compliance.sony.de/

This equipment is intended to be used with

the approved version(s) of software that are

indicated in the EU Declaration of

Conformity.

The software loaded on this equipment is

verified to comply with the essential

requirements of the Directive 2014/53/EU.

The software version can be checked in the

firmware setup item of the general setup

menu.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU Directives

This product has been manufactured by or

on behalf of Sony Corporation.

EU Importer: Sony Europe B.V.

Inquiries to the EU Importer or related to

product compliance in Europe should be

sent to the manufacturer’s authorized

representative, Sony Belgium, bijkantoor

van Sony Europe B.V., Da Vincilaan 7-D1, 1930

Zaventem, Belgium.

Disposal of waste batteries

and electrical and electronic

equipment (applicable in

the European Union and

other countries with

separate collection systems)

This symbol on the product, the battery or

on the packaging indicates that the product

and the battery shall not be treated as

household waste. On certain batteries this

symbol might be used in combination with a

chemical symbol. The chemical symbol for

lead (Pb) is added if the battery contains

more than 0.004% lead. By ensuring that

these products and batteries are disposed of

correctly, you will help to prevent potentially

negative consequences for the environment

and human health which could be caused by

inappropriate waste handling. The recycling

of the materials will help to conserve natural

resources. In case of products that for safety,

performance or data integrity reasons

require a permanent connection with an

incorporated battery, this battery should be

replaced by qualified service staff only. To

ensure that the battery and the electrical

and electronic equipment will be treated

properly, hand over these products at end-

of-life to the appropriate collection point for

the recycling of electrical and electronic

equipment. For all other batteries, please

view the section on how to remove the

battery from the product safely. Hand the

battery over to the appropriate collection

point for the recycling of waste batteries. For

more detailed information about recycling of

this product or battery, please contact your

local Civic Office, your household waste

disposal service or the shop where you

purchased the product or battery.

CAUTION

The following frequency 65 – 74 MHz range

is not allocated to sound broadcasting in the

European Common Allocations table and

cannot be used in Europe.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of

the unit becomes hot during use.

For details, see “Connection/Installation”

(page 21).

3GB

Disclaimer regarding services offered

by third parties

Services offered by third parties may be

changed, suspended, or terminated without

prior notice. Sony does not bear any

responsibility in these sorts of situations.

Warning if your car’s ignition has no

ACC position

Be sure to set the AUTO OFF function

(page 12). The unit will shut off completely

and automatically in the set time after the

unit is turned off and the clock is

displayed (i.e. press and hold OFF for 1

second), which prevents battery drain. If

you do not set the AUTO OFF function,

press and hold OFF until the display

disappears each time you turn the

ignition off.

4GB

Table of Contents

Guide to Parts and Controls. . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . 7

Resetting the Unit. . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock. . . . . . . . . . . . . . . . . . . . . . 7

Checking the Battery Voltage . . . . . . . . . . . 8

Connecting a USB Device. . . . . . . . . . . . . . . 8

Connecting Other

Portable Audio Device . . . . . . . . . . . . . . 8

Listening to the Radio

Listening to the Radio . . . . . . . . . . . . . . . . . 9

Using Radio Data System (RDS). . . . . . . . . . 9

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . 10

Playing a USB Device . . . . . . . . . . . . . . . . . 10

Searching and Playing Tracks . . . . . . . . . . . 11

Settings

Canceling the DEMO Mode . . . . . . . . . . . . 12

Basic Setting Operation . . . . . . . . . . . . . . . 12

General Setup (GENERAL) . . . . . . . . . . . . . 12

Sound Setup (SOUND) . . . . . . . . . . . . . . . . 13

Display Setup (DISPLAY). . . . . . . . . . . . . . . 14

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . 15

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 18

Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Parts List for Installation. . . . . . . . . . . . . . . 21

Connection . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 24

5GB

Guide to Parts and Controls

 PTY (program type)

Select PTY in RDS.

(browse) (page 11)

Enter the browse mode during playback.

(Not available when a USB device in

Android™ mode is connected.)

 Front panel release button

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the

source off and display the clock.

Press and hold for more than 2 seconds

to turn off the power and the display.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change

the source (timeout in 2 seconds).

MENU

Open the setup menu.

 Disc slot

 Display window

 USB port

 (disc eject)

 / (SEEK –/+)

Tune in radio stations automatically.

Press and hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 (back)

Return to the previous display.

MODE (page 9)

 EQ (equalizer)

Select an equalizer curve.

 Receptor for the remote commander

 Number buttons (1 to 6)

Receive stored radio stations. Press and

hold to store stations.

ALBUM /

Skip an album for audio device. Press and

hold to skip albums continuously.

(Not available when a USB device in

Android mode is connected.)

(repeat)

(Not available when a USB device in

Android mode is connected.)

(shuffle)

(Not available when a USB device in

Android mode is connected.)

 (play/pause)

Main unit

6GB

 EXTRA BASS

Reinforces bass sound in synchronization

with the volume level. Press to change

the EXTRA BASS setting: [1], [2], [OFF].

 AUX input jack

 DSPL (display)

Press to change display items.

SCRL (scroll)

Press and hold to scroll a display item.

7GB

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit

turns off, press the front panel

release button , then pull the panel

towards you to remove.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel,

the caution alarm will sound for a few

seconds. The alarm will only sound if the

built-in amplifier is used.

Resetting the Unit

Before operating the unit for the first time,

after replacing the car battery, or changing

the connections, you must reset the unit.

1 Press DSPL and EQ for more than

2seconds.

Note

Resetting the unit will erase the clock setting and

some stored contents.

Setting the area/region

After resetting the unit, the area/region

setting display appears.

1 Press ENTER while [SET AREA] is

displayed.

The area/region currently set appears.

2 Rotate the control dial to select

[EUROPE] or [RUSSIA], then press it.

3 Rotate the control dial to select [YES]

or [NO], then press it.

If the setting area/region is changed, the

unit is reset, then the clock is displayed.

This setting can be configured in the general

setup menu (page 12).

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK], then press it.

3 Rotate the control dial to select

[MANUAL], then press it.

The hour indication flashes.

4 Rotate the control dial to set the hour

and minute.

To move the digital indication, press

/ (SEEK –/+).

5 After setting the minute, press MENU.

The setup is complete and the clock

starts.

To display the clock

Press DSPL.

To set the clock automatically

Select [AUTO <RDS>] in step 3.

Getting Started

Attaching the front panel

8GB

Checking the Battery

Voltage

You can check the current battery voltage.

(Not available while the source is off and the

clock is displayed.)

1 Press DSPL repeatedly until the

battery voltage display appears.

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to

the AUX input jack (stereo mini jack)

on the unit with a connecting cord

(not supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the

connected device to other sources

Start playback of the portable audio device

at a moderate volume, and set your usual

listening volume on the unit.

Press MENU, then select [SOUND]  [SET AUX

VOL] (page 14).

9GB

Listening to the Radio

To listen to the radio, press SRC to select

[TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3 or MW/LW).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of

frequency on the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3 or MW/LW).

2 Perform tuning.

To tune manually

Press and hold / (SEEK –/+) to

locate the approximate frequency, then

press / (SEEK –/+) repeatedly to

fine adjust to the desired frequency.

To tune automatically

Press / (SEEK –/+).

Scanning stops when the unit receives a

station.

1 While receiving the station that you

want to store, press and hold a

number button (1 to 6) until [MEM]

appears.

1 Select the band, then press a number

button (1 to 6).

Using Radio Data System

(RDS)

AF continuously retunes the station to the

strongest signal in a network, and TA

provides current traffic information or traffic

programs (TP) if received.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

AF/TA], then press it.

3 Rotate the control dial to select [SET

AF-ON], [SET TA-ON], [SET AF/TA-ON]

or [SET AF/TA-OFF], then press it.

To store RDS stations with the AF and

TA setting

You can preset RDS stations along with an

AF/TA setting. Set AF/TA, then store the

station with BTM or manually. If you preset

manually, you can also preset non-RDS

stations.

To receive emergency announcements

With AF or TA on, emergency

announcements will automatically interrupt

the currently selected source.

To adjust the volume level during a

traffic announcement

Level will be stored into memory for

subsequent traffic announcements,

independently from the regular volume

level.

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

Setting alternative frequencies

(AF) and traffic announcement

(TA)

10GB

To stay with one regional program

(REGIONAL)

When the AF and REGIONAL functions are

on, you will not be switched to another

regional station with a stronger frequency. If

you leave this regional program’s reception

area, set [SET REGIONAL] in [GENERAL] to

[SET REG-OFF] during FM reception

(page 13).

This function does not work in the UK and

some other areas.

Local Link function (UK only)

This function enables you to select other

local stations in the area, even if they are not

stored on your number buttons.

During FM reception, press a number button

(1 to 6) on which a local station is stored.

Within 5 seconds, press again a number

button of the local station. Repeat this

procedure until the local station is received.

1 Press PTY during FM reception.

2 Rotate the control dial until the

desired program type appears, then

press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

AOA (Android Open Accessory) 2.0, MSC

(Mass Storage Class) and MTP (Media

Transfer Protocol) type USB devices*

compliant with the USB standard can be

used. Depending on the USB device, the

Android mode or MSC/MTP mode can be

selected on the unit.

Some digital media players or Android

smartphones may require setting to MTP

mode.

* e.g., a USB flash drive, digital media player,

Android smartphone

Notes

• For details on the compatibility of your USB device,

visit the support site on the back cover.

• Smartphones with Android OS 4.1 or higher

installed support Android Open Accessory 2.0

(AOA 2.0). However, some smartphones may not

fully support AOA 2.0 even if Android OS 4.1 or

higher is installed.

For details on the compatibility of your Android

smartphone, visit the support site on the back

cover.

• Playback of the following files is not supported.

MP3/WMA/FLAC:

– copyright-protected files

– DRM (Digital Rights Management) files

– Multi-channel audio files

MP3/WMA:

– lossless compression files

Selecting program types (PTY)

NEWS (News), AFFAIRS (Current Affairs), INFO

(Information), SPORT (Sports), EDUCATE

(Education), DRAMA (Drama), CULTURE

(Culture), SCIENCE (Science), VARIED (Varied),

POP M (Pop Music), ROCK M (Rock Music),

EASY M (M.O.R. Music), LIGHT M (Light

classical), CLASSICS (Serious classical), OTHER

M (Other Music), WEATHER (Weather), FINANCE

(Finance), CHILDREN (Children’s program),

SOCIAL (Social Affairs), RELIGION (Religion),

PHONE IN (Phone In), TRAVEL (Travel), LEISURE

(Leisure), JAZZ (Jazz Music), COUNTRY (Country

Music), NATION M (National Music), OLDIES

(Oldies Music), FOLK M (Folk Music),

DOCUMENT (Documentary)

Playback

11GB

Before making a connection, select the USB

mode (Android mode or MSC/MTP mode)

depending on the USB device (page 13).

1 Connect a USB device to the USB port

(page 8).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB].

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Searching and Playing

Tracks

Not available when a USB device in Android

mode is connected.

1 During playback, press (repeat) or

(shuffle) repeatedly to select the

desired play mode.

Playback in the selected play mode may

take time to start.

Available play modes differ depending on

the selected sound source.

Not available when a USB device in Android

mode is connected.

1 During CD or USB playback, press

(browse)* to display the list of search

categories.

When the track list appears, press

(back) repeatedly to display the desired

search category.

* During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it

to confirm.

3 Repeat step 2 to search the desired

track.

Playback starts.

To exit the Quick-BrowZer mode

Press (browse).

Not available when a USB device in Android

mode is connected.

1 During CD or USB playback, press

(browse).

2 Press  (SEEK +).

3 Rotate the control dial to select the

item.

The list is jumped in steps of 10% of the

total number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

Repeat play and shuffle play

Searching a track by name (Quick-

BrowZer™)

Searching by skipping items

(Jump mode)

12GB

Canceling the DEMO Mode

You can cancel the demonstration display

which appears when the source is off and

the clock is displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/

play mode.

Basic Setting Operation

You can set items in the following setup

categories:

General setup (GENERAL), Sound setup

(SOUND), Display setup (DISPLAY)

1 Press MENU.

2 Rotate the control dial to select the

setup category, then press it.

The items that can be set differ

depending on the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

General Setup (GENERAL)

AREA (area)

Specifies the area/region to use this unit:

[EUROPE], [RUSSIA].

If the area/region currently set is

changed, this unit is reset, then the clock

is displayed.

(Available only while the source is off and

the clock is displayed.)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK (clock) (page 7)

Sets the clock: [AUTO <RDS>], [MANUAL].

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF]

(page 7).

(Available only while the source is off and

the clock is displayed.)

BEEP (beep)

Activates the beep sound: [ON], [OFF].

AUTO OFF (auto off)

Shuts off automatically after a certain

time when the unit is turned off and the

clock is displayed (i.e. press and hold OFF

for 1 second): [ON] (30 minutes), [OFF].

STEERING (steering)

Registers/resets the setting of the

steering wheel remote control.

(Available only while the source is off and

the clock is displayed.)

STR CONTROL (steering control)

Selects the input mode of the connected

remote control. To prevent a malfunction,

be sure to match the input mode with the

connected remote control before use.

CUSTOM (custom)

Input mode for the steering wheel

remote control

PRESET (preset)

Input mode for the wired remote

control excluding the steering wheel

remote control

(Automatically selected when [RESET

CUSTOM] is performed.)

EDIT CUSTOM (edit custom)

Registers the functions (SOURCE, ATT,

VOL +/–, SEEK +/–) to the steering wheel

remote control:

 Rotate the control dial to select the

function you want to assign to the

steering wheel remote control, then

press it.

 While [REGISTER] is blinking, press and

hold the button on the steering wheel

remote control you want to assign the

function to. When registration is

complete, [REGISTERED] is displayed.

Settings

13GB

 To register other functions, repeat

steps  and .

(Available only when [STR CONTROL] is

set to [CUSTOM].)

RESET CUSTOM (reset custom)

Resets the registered functions of the

steering wheel remote control: [YES],

[NO].

(Available only when [STR CONTROL] is

set to [CUSTOM].)

Notes

• While making settings, only button operation

on the unit is available. For safety, park your car

before making this setting.

• If an error occurs while registering, all the

previously-registered information remains.

Restart registration from the function where

the error occurred.

• This function may not be available on some

vehicles. For details on the compatibility of

your vehicle, visit the support site on the back

cover.

USB MODE (USB mode)

Changes the USB mode: [ANDROID],

[MSC/MTP].

(Available only when the USB source is

selected.)

AF/TA (alternative frequencies/traffic

announcement)

Selects the alternative frequencies (AF)

and traffic announcement (TA) setting:

[AF-ON], [TA-ON], [AF/TA-ON], [AF/TA-

OFF].

(Available when any source is selected.)

REGIONAL (regional)

Restricts reception to a specific region:

[ON], [OFF].

(Available only when FM is received.)

BTM (best tuning memory) (page 9)

(Available only when the tuner is

selected.)

FIRMWARE (firmware)

(Available only while the source is off and

the clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back

cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES],

[NO].

Updating the firmware takes a few

minutes to complete. During the update,

do not turn the ignition to the OFF

position, nor remove the USB device.

Sound Setup (SOUND)

This setup menu is not available when the

source is off and the clock is displayed.

EQ10 PRESET (EQ10 preset)

Selects an equalizer curve from 10

equalizer curves or off:

[OFF], [R&B], [ROCK], [POP], [HIP-HOP],

[EDM], [JAZZ], [SOUL], [COUNTRY],

[KARAOKE]*, [CUSTOM].

The equalizer curve setting can be

memorized for each source.

* [KARAOKE] reduces the vocal sound but

cannot fully remove it during playback. Also,

using a microphone is not supported.

EQ10 CUSTOM (EQ10 custom)

Sets [CUSTOM] of EQ10.

Setting the equalizer curve: [BAND1] –

[BAND10] (32 Hz, 63 Hz, 125 Hz, 250 Hz,

500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz).

The volume level is adjustable in 1 dB

steps, from -6 dB to +6 dB.

BALANCE (balance)

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER (fader)

Adjusts the relative level: [FRONT-15] –

[CENTER] – [REAR-15].

14GB

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+6 dB] – [0 dB] – [-6 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [SUB

NORM], [SUB REV].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency:

[80Hz], [100Hz], [120Hz].

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off

frequency: [OFF], [80Hz], [100Hz], [120Hz].

AUX VOL (AUX volume)

Adjusts the volume level for each

connected auxiliary device:

[+18 dB] – [0 dB] – [-8 dB].

This setting negates the need to adjust

the volume level between sources.

(Available only when the AUX is selected.)

Display Setup (DISPLAY)

DIMMER (dimmer)

Change the display brightness: [OFF],

[ON], [CLK] (clock).

To set this function to be active only

during a fixed period, select [CLK], then

set the start and end times.

– To set the brightness when the dimmer

function is activated:

Set [DIMMER] to [ON], then adjust

[BRIGHTNESS].

– To set the brightness when the dimmer

function is deactivated:

Set [DIMMER] to [OFF], then adjust

[BRIGHTNESS].

The brightness setting is stored and

applied when the dimmer function is

activated or deactivated.

BRIGHTNESS (brightness)

Adjusts the display brightness. The

brightness level is adjustable: [1] – [10].

SND SYNC (sound synchronization)

Activates the synchronization of the

illumination with the sound: [ON], [OFF].

(Not available when no source is selected

and the clock is displayed.)

AUTO SCR (auto scroll)

Scrolls long items automatically: [ON],

[OFF].

(Not available when the AUX or tuner is

selected.)

15GB

Updating the Firmware

To update the firmware, visit the support site

on the back cover, then follow the online

instructions.

Note

During the update, do not remove the USB device.

Precautions

• Do not leave the front panel or audio

devices on the dashboard.

• When the unit is turned on, the power

antenna (aerial) extends automatically.

• Do not splash liquid onto the unit.

Moisture condensation

Do not splash liquid onto the discs. When

moisture condensation occur inside the unit,

remove the disc and wait for about an hour

for it to dry out; otherwise the unit will not

operate properly.

• Do not expose discs to direct sunlight or

heat sources such as hot air ducts, nor

leave it in a car parked in direct sunlight.

• Wipe the discs with a

cleaning cloth from the

center out. Do not use

solvents such as

benzine, thinner,

commercially available

cleaners.

• This unit is designed to

play discs that conform

to the Compact Disc (CD) standard.

DualDiscs and some of the music discs

encoded with copyright protection

technologies do not conform to the

Compact Disc (CD) standard, therefore,

these discs may not be playable by this

unit.

•Discs that this unit CANNOT play

– Discs with labels, stickers, or sticky tape

or paper attached. Doing so may cause a

malfunction, or may ruin the disc.

– Discs with non-standard shapes (e.g.,

heart, square, star). Attempting to do so

may damage the unit.

–8 cm (3

1

/4 in) discs.

Notes on CD-R/CD-RW discs

• If the multi-session disc begins with a CD-

DA session, it is recognized as a CD-DA

disc, and other sessions are not played.

•Discs that this unit CANNOT play

– CD-R/CD-RW of poor recording quality.

– CD-R/CD-RW recorded with an

incompatible recording device.

– CD-R/CD-RW which is finalized

incorrectly.

– CD-R/CD-RW other than those recorded

in music CD format or MP3 format

conforming to ISO9660 Level 1/Level 2,

Joliet/Romeo or multi-session.

If you have any questions or problems

concerning your unit that are not covered in

this manual, consult your nearest Sony

dealer.

Additional Information

Notes on discs

Playback order of audio files

Folder (album)

Audio file (track)

16GB

Maintenance

Cleaning the connectors

Avoid touching the connectors directly. The

unit may not function properly if the

connectors between the unit and the front

panel are not clean. In order to prevent this,

detach the front panel (page 7) and clean

the connectors with a cotton swab. Do not

apply too much force. Otherwise, the

connectors may be damaged.

Note

For safety, do not remove the front panel while

driving.

Specifications

Tuner section

FM

Tuning range:

When [AREA] is set to [EUROPE]:

87.5 MHz – 108.0 MHz

When [AREA] is set to [RUSSIA]:

FM1/FM2: 87.5 MHz – 108.0 MHz

(at 50 kHz step)

FM3: 65 MHz – 74 MHz (at 30 kHz step)

Usable sensitivity: 7 dBf

Signal-to-noise ratio: 73 dB

Separation: 50 dB at 1 kHz

MW/LW

Tuning range:

531 kHz – 1,602 kHz (MW),

153 kHz – 279 kHz (LW)

Sensitivity: MW: 26 V, LW: 50 V

CD Player section

Signal-to-noise ratio: 95 dB

Frequency response: 20 Hz – 20,000 Hz

Maximum number*

1

of:

Folders (albums)*

2

: 150

Files (tracks) and folders*

3

: 300

Displayable characters for a folder/file

name:

32 (Joliet)/64 (Romeo)

Corresponding codec: MP3 (.mp3), WMA

(.wma)

*1 CD-R/CD-RW only

*2 including the root folder

*3 may be less than the measured value if folder/

file names contain many characters

USB Player section

Interface: USB (Full speed)

Maximum current: 500 mA

Maximum number of recognizable folders

and files:

Folders (albums): 256

Files (tracks) per folder: 256

Compatible Android Open Accessory

protocol (AOA): 2.0

17GB

Corresponding codec:

MP3 (.mp3)

Bit rate: 8 kbps – 320 kbps (Supports

VBR (Variable Bit Rate))

Sampling rate: 16 kHz – 48 kHz

WMA (.wma)

Bit rate: 32 kbps – 192 kbps (Supports

VBR (Variable Bit Rate))

Sampling rate: 32 kHz, 44.1 kHz,

48 kHz

FLAC (.flac)

Bit depth: 16 bit, 24 bit

Sampling rate: 44.1 kHz, 48 kHz

Supported file system: FAT16, FAT32

Power amplifier section

Output: Speaker outputs

Speaker impedance: 4  – 8 

Maximum power output: 55 W × 4 (at 4 )

General

Power requirements: 12 V DC car battery

(negative ground (earth))

Rated current consumption: 10 A

Dimensions:

Approx. 178 mm × 50 mm × 176 mm

(7

1

/8 in × 2 in × 7 in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 53 mm × 159 mm

(7

1

/4 in × 2

1

/8 in × 6

3

/8 in) (w/h/d)

Mass: Approx. 1.2 kg (2 lb 11 oz)

Package contents:

Main unit (1)

Parts for installation and connections

(1 set)

Ask the dealer for detailed information.

Design and specifications are subject to

change without notice.

Windows Media is either a registered trademark or

trademark of Microsoft Corporation in the United

States and/or other countries.

This product is protected by certain intellectual

property rights of Microsoft Corporation. Use or

distribution of such technology outside of this

product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

Android is a trademark of Google LLC.

libFLAC

Redistribution and use in source and binary forms,

with or without modification, are permitted

provided that the following conditions are met:

– Redistributions of source code must retain the

above copyright notice, this list of conditions and

the following disclaimer.

– Redistributions in binary form must reproduce the

above copyright notice, this list of conditions and

the following disclaimer in the documentation

and/or other materials provided with the

distribution.

– Neither the name of the Xiph.org Foundation nor

the names of its contributors may be used to

endorse or promote products derived from this

software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT

HOLDERS AND CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE

FOUNDATION OR CONTRIBUTORS BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

Copyrights

18GB

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below,

check the connection and operating

procedures.

For details on using the fuse and removing

the unit from the dashboard, see

“Connection/Installation” (page 21).

If the problem is not solved, visit the support

site on the back cover.

General

No sound or the sound is very low.

 The position of the fader control [FADER]

is not set for a 2-speaker system.

 The volume of the unit and/or connected

device is very low.

– Increase the volume of the unit and

connected device.

No beep sound.

 An optional power amplifier is connected

and you are not using the built-in

amplifier.

Stored stations and correct time are

erased.

The fuse has blown.

Makes a noise when the position of the

ignition is switched.

 The leads are not matched correctly with

the car’s accessory power connector.

During playback or reception, the

demonstration mode starts.

 If no operation is performed for 5 minutes

with [DEMO-ON] set, the demonstration

mode starts.

– Set [DEMO-OFF] (page 12).

The display disappears from/does not

appear in the display window.

 The connectors are dirty (page 16).

The display/illumination flashes.

 The power supply is not sufficient.

– Check that the car battery supplies

enough power to the unit. (The power

requirement is 12 V DC.)

The operation buttons do not function.

The disc will not eject.

 The connection is not correct.

– Press DSPL and EQ for more than

2 seconds to reset the unit.

The contents stored in memory are

erased.

The clock set automatically is not accurate.

 The clock data on radio waves is not

accurate.

– Set the clock manually (page 7).

Radio reception

The radio reception is poor.

Static noise occurs.

 Connect the antenna (aerial) firmly.

65 MHz to 74 MHz in FM3 cannot be tuned

in.

 [AREA] is set to [EUROPE].

– Set [AREA] to [RUSSIA] (page 12).

RDS

RDS services cannot be received (when

[AREA] is set to [RUSSIA]).

 FM3 is selected.

– Select FM1 or FM2.

 RDS services are unavailable in the current

region.

The SEEK starts after a few seconds of

listening.

 The station is non-TP or has weak signal.

– Deactivate TA (page 9).

No traffic announcements.

 Activate TA (page 9).

 The station does not broadcast any traffic

announcements despite being TP.

– Tune in another station.

PTY displays [- - - - - - - -].

 The current station is not an RDS station,

or the radio reception is poor.

19GB

Program service name flashes.

 There is no alternative frequency for the

current station.

– Press / (SEEK –/+) while the

program service name is flashing. [PI

SEEK] appears and the unit starts

searching for another frequency with

the same PI (program identification)

data.

CD playback

The disc does not play.

 Defective or dirty disc.

 The CD-R/CD-RW is not for audio use

(page 15).

MP3/WMA files cannot be played.

 The disc is incompatible with the MP3/

WMA format and version. For details on

playable discs and formats, visit the

support site on the back cover.

MP3/WMA files take longer to play than

others.

 The following discs take a longer time to

start playback.

– A disc recorded with a complicated tree

structure.

– A disc recorded in Multi Session.

– A disc to which data can be added.

USB device playback

A USB device takes longer to play.

 The USB device contains files with a

complicated tree structure.

The audio file cannot be played.

 For details on supported formats, see

“Specifications” (page 16).

If the audio file still cannot be played, refer

to the operating instructions supplied with

the USB device, or contact the

manufacturer of the USB device.

Operations for skipping an album,

skipping items (Jump mode), and

searching a track by name (Quick-

BrowZer) cannot be performed.

 Set [USB MODE] to [MSC/MTP] (page 13).

The sound cannot be output during

playback in Android mode.

 Check the status of the audio playback

application on the Android smartphone.

Messages

The following messages may appear or flash

during operation.

INVALID: The selected operation could be

invalid.

READ

 Wait until reading is complete and

playback starts automatically. This may

take some time depending on the file

organization.

(underscore): The character cannot be

displayed.

For CD playback:

CD ERROR

 Clean or insert the disc correctly, or make

sure the disc is not blank or defective.

CD NO DISC

 Insert a disc containing playable files

(page 16).

CD NO MUSIC

 Insert a disc containing playable files

(page 16).

CD PUSH EJT: The disc could not be ejected

properly.

 Press  (eject).

or : The beginning or the end

of the disc has been reached.

20GB

For USB device playback:

HUB NO SUPRT: USB hubs are not

supported.

NOT SUPPORT ANDROID MODE

 A USB device not supporting AOA

(Android Open Accessory) 2.0 is

connected to the unit while [USB MODE] is

set to [ANDROID].

– Set [USB MODE] to [MSC/MTP] (page 13).

USB ERROR

 Connect the USB device again.

USB NO DEV

 Make sure the USB device or USB cable is

securely connected.

USB NO MUSIC

 Connect a USB device containing playable

files (page 16).

USB NO SUPRT

 For details on the compatibility of your

USB device, visit the support site on the

back cover.

USB OVERLOAD: The USB device is

overloaded.

 Disconnect the USB device, then press SRC

to select another source.

 The USB device has a fault, or an

unsupported device is connected.

For RDS operation:

NO AF: No alternative frequencies.

 Press / (SEEK –/+) while the

program service name is flashing. The unit

starts searching for another frequency

with the same PI (program identification)

data ([PI SEEK] appears).

NO PI: No program identification. The

selected station has no PI (program

identification) data.

 Select another station.

NO TP: No traffic programs.

 The unit will continue searching for

available TP stations.

For steering wheel remote control

operation:

ERROR

 Register again from the function where

the error occurred (page 12).

TIMEOUT

 Try completing the registration while

[REGISTER] is blinking (about 6 seconds)

(page 12).

For firmware update operation:

FILE ERROR: The updater is not stored in the

USB device.

 Store the updater in the USB device, then

try again (page 15).

UPDATE ERROR PRESS ENTER: Firmware

update is not completed properly.

 Press ENTER to clear the message, then try

again.

During the update, do not turn the

ignition to the OFF position, nor remove

the USB device (page 15).

If these solutions do not help improve the

situation, consult your nearest Sony dealer.

If you take the unit to be repaired because of

device playback trouble, bring the device

that was used at the time the problem

began.

La pagina sta caricando ...

Sony CDX-G1301U Manuale del proprietario

Questo manuale è adatto anche per

Sony CDX-G1301U Manuale del proprietario

in altre lingue

Documenti correlati