Dell Precision 3640 Tower Service Manuale del proprietario

Precision 3640 Tower

Service Manual

0.0.0.0

Regulatory Model: D24M

Regulatory Type: D24M004

May 2020

Rev. A00

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dell Precision 3640

CMG15 o cerca il tuo prodotto tra le migliori offerte di PC Desktop e Workstation

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

1 Working on your computer............................................................................................................ 6

Safety instructions.................................................................................................................................................................6

Before working inside your computer........................................................................................................................... 6

Safety precautions...........................................................................................................................................................7

Electrostatic discharge—ESD protection.................................................................................................................... 7

ESD field service kit ........................................................................................................................................................8

Transporting sensitive components.............................................................................................................................. 8

After working inside your computer.............................................................................................................................. 9

2 Technology and components........................................................................................................10

DDR4......................................................................................................................................................................................10

Intel Rapid Storage Technology (Intel RST)......................................................................................................................11

Advantages of DisplayPort over USB Type-C..................................................................................................................13

HDMI 2.0............................................................................................................................................................................... 13

3 Major components of your system................................................................................................15

4 Disassembly and reassembly........................................................................................................ 16

Recommended tools............................................................................................................................................................ 16

Screw list...............................................................................................................................................................................16

Chassis rubber feet..............................................................................................................................................................16

Removing the chassis rubber feet............................................................................................................................... 16

Installing the chassis rubber feet..................................................................................................................................18

Cover.....................................................................................................................................................................................20

Removing the cover......................................................................................................................................................20

Installing the cover......................................................................................................................................................... 21

SD card—optional...............................................................................................................................................................22

Removing the SD card .................................................................................................................................................22

Installing the SD card.................................................................................................................................................... 23

Bezel......................................................................................................................................................................................24

Removing the front bezel............................................................................................................................................. 24

Installing the front bezel............................................................................................................................................... 25

Hard drive.............................................................................................................................................................................25

Removing the 3.5-inch hard drive ..............................................................................................................................25

Installing the 3.5-inch hard drive ................................................................................................................................ 26

Removing the 2.5-inch hard drive .............................................................................................................................. 27

Installing the 2.5-inch hard drive ................................................................................................................................ 29

PSU hinge..............................................................................................................................................................................31

Opening the PSU hinge................................................................................................................................................. 31

Closing the PSU hinge.................................................................................................................................................. 32

Graphics card....................................................................................................................................................................... 33

Removing the graphics card........................................................................................................................................ 33

Installing the graphics card...........................................................................................................................................35

Memory module...................................................................................................................................................................38

Contents

Contents 3

Removing the memory module.................................................................................................................................... 38

Installing the memory module...................................................................................................................................... 38

Speaker.................................................................................................................................................................................39

Removing speaker......................................................................................................................................................... 39

Installing the speaker.....................................................................................................................................................39

Coin cell battery...................................................................................................................................................................40

Removing the coin cell battery.................................................................................................................................... 40

Installing the coin cell battery....................................................................................................................................... 41

Power supply unit................................................................................................................................................................ 42

Removing the power supply unit................................................................................................................................. 42

Installing the power supply unit ...................................................................................................................................44

Optical drive......................................................................................................................................................................... 46

Removing the optical drive...........................................................................................................................................46

Installing the optical drive............................................................................................................................................. 48

WLAN module and SMA antenna......................................................................................................................................49

Removing WLAN module and SMA antenna............................................................................................................. 49

Installing WLAN module and SMA antenna................................................................................................................ 51

IO panel.................................................................................................................................................................................52

Removing the IO panel..................................................................................................................................................52

Installing the IO panel.................................................................................................................................................... 57

Solid state drive................................................................................................................................................................... 62

Removing the PCIe SSD card...................................................................................................................................... 62

Installing the PCIe SSD card........................................................................................................................................ 63

Power button module......................................................................................................................................................... 65

Removing power button module................................................................................................................................. 65

Installing power button module....................................................................................................................................66

Heatsink assembly...............................................................................................................................................................68

Removing heatsink assembly - 65 W or 80 W CPU................................................................................................. 68

Removing blower and heat sink assembly — 125 W CPU.......................................................................................69

Installing heatsink assembly - 65 W or 80 W CPU.....................................................................................................71

Installing blower and heat sink assembly — 125 W CPU..........................................................................................72

VR heat sink......................................................................................................................................................................... 74

Removing VR heatsink.................................................................................................................................................. 74

Installing VR heatsink.................................................................................................................................................... 75

Front fan............................................................................................................................................................................... 77

Removing front fan........................................................................................................................................................77

Installing front fan..........................................................................................................................................................79

System fan............................................................................................................................................................................ 81

Removing system fan.................................................................................................................................................... 81

Installing system fan...................................................................................................................................................... 82

Optional IO card...................................................................................................................................................................84

Removing optional IO card........................................................................................................................................... 84

Installing the optional IO card ......................................................................................................................................84

Processor..............................................................................................................................................................................86

Removing the processor...............................................................................................................................................86

Installing the processor................................................................................................................................................. 86

Intrusion switch....................................................................................................................................................................87

Removing intrusion switch............................................................................................................................................87

Installing intrusion switch..............................................................................................................................................88

System board.......................................................................................................................................................................89

4

Contents

Removing the system board........................................................................................................................................ 89

Installing the system board........................................................................................................................................... 91

System board layout..................................................................................................................................................... 95

5 Troubleshooting......................................................................................................................... 97

Real-Time Clock (RTC Reset)........................................................................................................................................... 97

System diagnostic lights..................................................................................................................................................... 97

Diagnostic error messages................................................................................................................................................. 98

System error messages..................................................................................................................................................... 101

Recovering the operating system.....................................................................................................................................101

Flashing BIOS (USB key).................................................................................................................................................. 102

Flashing the BIOS...............................................................................................................................................................102

WiFi power cycle................................................................................................................................................................102

6 Getting help and contacting Dell................................................................................................ 103

A Cable cover ............................................................................................................................. 105

B Dust filter .................................................................................................................................111

Contents

5

Working on your computer

Safety instructions

Prerequisites

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise

noted, each procedure included in this document assumes that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.

About this task

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the power source.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For

additional safety best practices information, see the Regulatory Compliance Homepage

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

simple repairs as authorized in your product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow

the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching

an unpainted metal surface at the same time as touching a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by

its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables

have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you

disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also,

before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Before working inside your computer

About this task

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

Steps

1. Ensure that you follow the Safety instructions.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3. Turn off your computer.

4. Disconnect all the network cables from the computer.

CAUTION:

To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from

the network device.

5. Disconnect your computer and all attached devices from the electrical outlets.

1

6 Working on your computer

6. Press and hold the power button while the computer is unplugged to ground the system board.

NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching

an unpainted metal surface at the same time as touching a connector on the back of the computer.

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or reassembly:

• Turn off the system and all attached peripherals.

• Disconnect the system and all attached peripherals from AC power.

• Disconnect all network cables, telephone, and telecommunications lines from the system.

• Use an ESD field service kit when working inside any to avoid electrostatic discharge (ESD) damage.

• After removing any system component, carefully place the removed component on an anti-static mat.

• Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially

powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and suspended into a sleep

mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board.

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the use of a

field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare metal and never to a

painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and ensure that you remove all jewelry

such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,

memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent

problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is

an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in

previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

• Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate

and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and

immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

• Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures

means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the

tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may

take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

• Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide

adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased

sensitivity to ESD damage.

• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing

material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static

electricity from your body.

• Before transporting a static-sensitive component, place it in an anti-static container or packaging.

Working on your computer

7

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-

static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

• Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an anti-

static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system

being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-

sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

• Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare

metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily

placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is

known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be

aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a

wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at

least once per week.

• ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a

best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the

best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have

one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to

test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

• Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are

insulators and often highly charged.

• Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,

deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a

rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work

area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is

being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as

Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically

handling any hardware components

• ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are

preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in.

The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the

new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts

should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the

ESD mat, in the system, or inside an anti-static bag.

• Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be

returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all

times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while

performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in

anti-static bags for safe transport.

Lifting equipment

Adhere to the following guidelines when lifting heavy weight equipment:

CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.

1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.

2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.

3. Lift with your legs, not your back.

8

Working on your computer

4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.

5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting your

body and back.

6. Follow the same techniques in reverse to set the load down.

After working inside your computer

About this task

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your

computer.

Steps

1. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

2. Connect your computer and all attached devices to their electrical outlets.

3. Turn on your computer.

4. If required, verify that the computer works correctly by running the diagnostic tool.

Working on your computer 9

Technology and components

This chapter details the technology and components available in the system.

DDR4

DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512

GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM. DDR4 synchronous dynamic random-access memory is keyed

differently from both SDRAM and DDR to prevent the user from installing the wrong type of memory into the system.

DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. DDR4 also

supports a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep

power-down mode is expected to reduce standby power consumption by 40 to 50 percent.

DDR4 Details

There are subtle differences between DDR3 and DDR4 memory modules, as listed below.

Key notch difference

The key notch on a DDR4 module is in a different location from the key notch on a DDR3 module. Both notches are on the insertion edge

but the notch location on the DDR4 is slightly different, to prevent the module from being installed into an incompatible board or platform.

Figure 1. Notch difference

Increased thickness

DDR4 modules are slightly thicker than DDR3, to accommodate more signal layers.

Figure 2. Thickness difference

Curved edge

DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation.

2

10 Technology and components

Figure 3. Curved edge

Memory Errors

Memory errors on the system display 2,3 failure code. If all memory fails, the LCD does not turn on. Troubleshoot for possible memory

failure by trying known good memory modules in the memory connectors on the bottom of the system or under the keyboard, as in some

portable systems.

NOTE: The DDR4 memory is imbedded in board and not a replaceable DIMM as shown and referred.

Intel Rapid Storage Technology (Intel RST)

The following article provides an overview of the Intel Rapid Storage Technology application and its features:

Overview

Intel Rapid Storage Technology (IRST) is a hardware, firmware and, software-based RAID solution. IRST was previously known as Matrix

RAID. IRST allows for creation of two RAID volumes on a single RAID array where both the volumes can be of the same or different type.

IRST encapsulates newer level of protection with better performance, and low power consumption. IRST user interface simplifies creation

and management of storage assets.

The fault tolerance is averted using one of the following RAID levels:

1. RAID 0 (Striping):

Multiple storage devices are combined to what appears to be a single virtual drive. Data is arranged as blocks that are spread across

multiple storage devices using process called striping. RAID 0 uses Read/ Write capabilities of two or more storage devices in parallel,

enhancing performance. There is no redundancy, hence if any of the storage devices fails, the RAID has to be re-created.

2. RAID 1 (Mirroring):

Two storage devices are mirrored or duplicated to achieve redundancy and hence enhance reliability in an event of single drive failure.

The performance is that of a single drive.

Technology and components

11

3. RAID 5 (Striping with Parity):

In this RAID level, data is stripped into blocks and spread across three or more storage devices. Each block contains the data and a

parity for fault tolerance. In an event of a drive failure, the parity helps build the lost piece of data. To further enhance the write

performance, IRST uses Volume Write-Back Cache and Coalescer. The Volume Write-Back allows writes to be buffered, and

Coalescer allows multiple write requests to be combined to reduce the overhead on parity calculation.

4. RAID 10 (Striping and Mirroring)):

RAID 10 is created, mirroring (RAID 1) the stripped (RAID 0) array. This RAID level uses four or more storage devices. It has great

reliability like a RAID 1 and performance like a RAID 0.

RAID-ready

A RAID-Ready configuration allows migration from one non-RAID SATA drive to a SATA RAID configuration.

NOTE: A reinstall of the operating system is not required for the migration.

A RAID-Ready system must meet the following requirements:

• Supported Intel Chipsets

• One Serial ATA (SATA) hard drive

• RAID controller enabled in the system setup

• BIOS that includes the IRST option ROM

• IRST software

• Hard drive partition with at least 5 MB of free space

12

Technology and components

Features of RAID-enabled systems:

• Intel Rapid Recover Technology - This technology provides full data redundancy by copying data from a designated source drive

(master disk) to a designated destination drive (recovery disk). Data updates of recovery volumes can be continuous or on request.

• Intel Rapid RAID : - This technology allows creation of RAID 0, RAID 1, RAID 5, and RAID 10 volumes on desktop and mobile

platforms. Data is distributed across two or more disks to provide data redundancy or to enhance data storage performance.

• Intel Matrix RAID Technology - This technology allows two independent RAID volumes to be created on a single array. The first

volume occupies part of the array, leaving space for the second volume. The array may consist of two to six SATA disks depending on

the volume types.

• Native command queuing - A feature that allows SATA disks to accept more than one command at a time. With multiple disks that

support NCQ, storage performance is increased on random workloads by allowing the disk to internally optimize the order of

commands.

• Disk capacity greater than 2 TB (Option ROM support) - This feature supports hard disks and solid-state drives with a capacity

greater than 2 TB that are reported as pass-through devices (available) or used in a RAID configuration. Besides booting from a

system disk greater than 2 TB is allowed, if the version of the option ROM in your system supports this feature.

• Password-protected disks - This feature provides high-level security and protection for the data on your disks with a password,

denying access from any unauthorized user.

Advantages of DisplayPort over USB Type-C

• Full DisplayPort audio/video (A/V) performance (up to 4K at 60Hz)

• Reversible plug orientation and cable direction

• Backwards compatibility to VGA, DVI with adaptors

• SuperSpeed USB (USB 3.1) data

• Supports HDMI 2.0a and is backwards compatible with previous versions

HDMI 2.0

This topic explains the HDMI 2.0 and its features along with the advantages.

HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an

interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or

video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable

reduction and content protection provisions. HDMI supports standard, enhanced, or high-definition video, plus multichannel digital audio

on a single cable.

HDMI 2.0 Features

• HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled

devices without a separate Ethernet cable

• Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio

system, eliminating the need for a separate audio cable

• 3D - Defines input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications

• Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings

based on content type

• Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics

• 4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema

systems used in many commercial movie theaters

• HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p

• Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique

demands of the motoring environment while delivering true HD quality

Advantages of HDMI

• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.

• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a

simple, cost-effective manner

• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound

Technology and components

13

• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables

currently used in A/V systems

• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality

14 Technology and components

Major components of your system

1. Cover

2. System fan

3. IO panel

4. Power button module

5. Optical drive

6. Hard drive

7. Bezel

8. Hard drive

9. Chasis

10. Power supply unit

11. System board

12. Front fan

13. Processor

14. Heatsink assembly

NOTE:

Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative

for purchase options.

3

Major components of your system 15

Disassembly and reassembly

Recommended tools

The procedures in this document require the following tools:

• Phillips # 1 screwdriver

• Small flat blade screwdriver

Screw list

The following table provides the list of screws that are used for securing different components to the computer.

Table 1. Screw list

Component

#6-32x1/4'' M2x2.5 M3X3 M2X3.5

Power supply bracket 2

Power supply unit 4

Heat sink blower (95 W heat sink solution) 3

System-fan bracket 1

System board 8

IO panel 1

Security-lock metal bracket 2

Solid-state drive (SSD) card 1

Optical drive bracket 1

Optional IO card 2

WLAN card and SMA antenna module 1

Chassis rubber feet

Removing the chassis rubber feet

Steps

1. Follow the procedure in Before Working Inside Your Computer.

4

16 Disassembly and reassembly

2. Pull one end of rubber feet out of the slot [1] and slide the rubber feet to remove it from the system [2].

Figure 4. Front rubber feet removal

Disassembly and reassembly

17

Figure 5. Rear rubber feet removal

Installing the chassis rubber feet

Steps

1. Insert one end of the rubber feet into the slot [1] and slide it to secure it to the system [2] and press the other end to secure it to the

system [3].

18

Disassembly and reassembly

Figure 6. Front rubber feet installation

Disassembly and reassembly

19

Figure 7. Rear rubber feet installation

2. Follow the procedure in After Working Inside Your Computer.

Cover

Removing the cover

Steps

1. Follow the procedure in Before Working Inside Your Computer.

2. Pull the release latch to release the cover [1].

NOTE: Release latch may have been secured with a security screw. Remove the security screw to release the cover.

20 Disassembly and reassembly

La pagina sta caricando ...

Dell Precision 3640 Tower Service Manuale del proprietario

Dell Precision 3640 Tower Service Manuale del proprietario

in altre lingue

Altri documenti