Yamaha NS-B310 Manuale del proprietario

Categoria
Parete
Tipo
Manuale del proprietario

Questo manuale è adatto anche per

NS-B310
NS-C310
Speaker
Enceinte
UTG
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES
i En
Thank you for selecting this YAMAHA product.
Read this before using the speaker.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install the speaker in a cool, dry, clean place - away from
windows, heat sources, sources of excessive vibration, dust,
moisture and cold. Avoid sources of electrical noise
(transformers, motors). To prevent fire or electrical shock, do
not expose this unit to rain or water.
To prevent the enclosure from warping or discoloring, do not
place the speaker where it will be exposed to direct sunlight or
excessive humidity.
Do not place the following objects on the speaker:
Glass, china, small metallic etc.
If glass, etc., falls as a result of vibration and breaks, it may
cause personal injury.
A burning candle, etc.
If the candle falls as a result of vibrations, it may cause fire
and personal injury.
A vessel with water in it
If the vessel falls as a result of vibrations and water spills, it
may cause damage to the speaker, and/or you may get an
electric shock.
Do not place the speaker where foreign material such as
dripping water. It might cause fire, damage to this unit, and/or
personal injury.
Do not place the speaker where it is liable to be knocked over
or struck by falling objects. Stable placement will also ensure
better sound performance.
Placing the speaker on the same shelf or rack as the turntable
can result in acoustical feedback.
Never put a hand or a foreign object into the port located on the
rear of the speaker, as this might cause personal injury and/or
damage to the speaker.
When moving the speaker, do not hold the port, as it might
cause personal injury and/or damage to the speaker.
Any time you notice distortion, reduce the volume control on
your amplifier. Never allow your amplifier to be driven into
“clipping.” Otherwise the speaker may be damaged.
When using an amplifier with a rated output power higher than
the nominal input power of the speaker, care should be taken
never to exceed the speaker’s maximum input.
Do not attempt to clean the speaker with chemical solvents, as
this might damage the finish. Use a clean, dry cloth.
Do not attempt to modify or repair the speaker. Contact
qualified YAMAHA service personnel when any service is
needed. The cabinet should never be opened for any reasons.
Secure placement and installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or installation of
speakers.
PRECAUTIONS
Information for Users on Collection and Disposal of Old
Equipment
This symbol on the products, packaging, and/
or accompanying documents means that used
electrical and electronic products should not
be mixed with general household waste.
For proper treatment, recovery and recycling
of old products, please take them to applicable
collection points, in accordance with your
national legislation and the Directives 2002/
96/EC.
By disposing of these products correctly, you
will help to save valuable resources and
prevent any potential negative effects on
human health and the environment which
could otherwise arise from inappropriate
waste handling.
For more information about collection and
recycling of old products, please contact your
local municipality, your waste disposal
service or the point of sale where you
purchased the items.
[Information on Disposal in other Countries
outside the European Union]
This symbol is only valid in the European
Union. If you wish to discard these items,
please contact your local authorities or dealer
and ask for the correct method of disposal.
English
1 En
Using as 2ch stereo speakers
Better stereo images will be obtained when the speakers are
slightly angled in towards the listeners.
Using as front speakers and surround
speakers in a surround system
Position the speakers on both sides of the TV. The positioning of
speakers is important, since this dictates the overall sound quality
of the surround system. Set up the speakers on the basis of your
listening position by following the owner’s manual supplied with
your amplifier.
And mount the speakers on a wall or place the speakers on a shelf.
Determine the best position by following the owner’s manual
supplied with your amplifier.
To mount the speakers on a wall by using
the attached mounting bracket
Fasten screws into a firm wall or wall support as shown in the
figure, and hang the holes of the mounting bracket on the
protruding screws.
* Make sure that the screws are secured in the narrow sections
of the holes.
Note
Placing this unit too close to a CRT TV set might impair
picture color or create a buzzing noise. Should this happen,
move the speaker away (more than 20 cm (7-7/8”)) from the
TV set.
When using a PDP or LCD TV, it would not happen.
WARNING
NS-B310 weighs 1.6 kg (3 lbs. 8 oz.). Do not mount it on thin
plywood or a wall with soft surface material. If mounted,
the screws may come out and the speaker may fall. This may
damage the speaker, or cause personal injury.
Do not install the speaker on a wall with nails, adhesives, or
any other unstable hardware. Long term use and vibrations
may cause it to fall.
To avoid accidents resulting from tripping over loose
speaker cables, fix them securely to the floor or wall.
SUPPLIED ACCESSORIES
(Only for NS-C310)
PLACING THE SPEAKERS
For NS-B310
Fastener × 2
NS-B310
Front
NS-C310
NS-B310
Surround
Subwoofer
You can also use the screw holes on the bottom of the speaker
for installing the speaker using a commercially available
speaker bracket (if you do not use the attached mounting
bracket).
Diameter. 3.5 to 4 mm
(1/8” to 3/16”)
3 mm
(1/8”)
Min.
20 mm
(13/16”)
Wall or wall
support
Tapping screw
(Available at the hardware store)
26 mm
(1”)
Screw holes
Diameter: 6 mm (1/4”)
Hole Depth: 14 mm (9/16”)
60 mm (2-3/8”)
2 En
Using as center speaker
Place the speaker on a TV rack or other stable surface. To prevent
the speaker from falling down, attach the fasteners provided in
each corner of the speaker’s underside.
To mount the speakers on a wall by using
the attached mounting bracket
Fasten screws into a firm wall or wall support as shown in the
figure, and hang the holes of the mounting bracket on the
protruding screws.
Note
Placing this unit too close to a CRT TV set might impair
picture color or create a buzzing noise. Should this happen,
move the speaker away (more than 20 cm (7-7/8”)) from the
TV set.
When using a PDP or LCD TV, it would not happen.
WARNING
NS-C310 weighs 2.9 kg (6 lbs. 6 oz.). Do not mount it on thin
plywood or a wall with soft surface material. If mounted,
the screws may come out and the speaker may fall. This may
damage the speaker, or cause personal injury.
Do not touch the adhesive surface after peeling off the seal
as this will weaken its adhesive strength.
Thoroughly wipe clean the surface where the fasteners are
to be attached. Note that adhesive strength is weakened if
the surface is dirty, oily or wet, and that this may cause the
center speaker to drop.
Do not install the speaker on a wall with nails, adhesives, or
any other unstable hardware. Long term use and vibrations
may cause it to fall.
To avoid accidents resulting from tripping over loose
speaker cables, fix them securely to the floor or wall.
For NS-C310
Fastener
Make sure that the screws are secured in the
narrow sections of the holes.
320 mm
(12-9/16”)
Diameter. 3.5 to 4 mm
(1/8” to 3/16”)
3 mm
(1/8”)
Min.
20 mm
(13/16”)
Tapping screw
(Available at the hardware store)
Wall or wall
support
English
3 En
Before making connections, make sure that the amplifier is
switched off.
Connect the screw-type input terminals at the rear of the
speakers to the speaker output terminals of the amplifier (or
receiver) with the speaker cable.
Connect the (+) terminals on the amplifier (or receiver) to the
(+) terminal of each speaker, making sure to confirm the color-
coded wire of the cable at each end. Use the other wire of the
cable to connect the (–) terminals of the components.
Connect one speaker to the left (marked L) terminals of your
amplifier, and another speaker to the right (marked R)
terminals, making sure not to reverse the polarity (+, –). If one
speaker is connected with reversed polarity the sound will be
unnatural and lack bass.
How to connect
1 Loosen the knob.
2 Remove 10 mm (3/8”) of insulation from each end of the
cables, and twist the exposed conductors together neatly and
tightly, as shown below.
3 Insert the bare wire.
4 Tighten the knob and secure the cables.
Test the firmness of the connection by pulling lightly on the
cables at the terminal.
Notes
Do not let the bare speaker wires touch each other as this
could damage the speaker or the amplifier, or both.
Do not insert the insulation into the hole. Sound may not be
produced.
When using a banana plug
Note
Do not take off this cover unless using a banana plug.
1 Remove the cover by pulling it toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
CONNECTIONS TO YOUR
AMPLIFIER
Loosen
Black (–)
Tighten
Red (+)
NS-B310
Amplifier or
receiver
NS-C310
NS-B310
Loosen
Black (–)
Tighten
Red (+)
Good No Good
10 mm
(3/8 ”)
Banana plug
Cover
4 En
The front cover is attached to protect the speaker, but you can
remove it if necessary.
The front cover is fixed by magnets. Hold the speaker with one
hand, and pull the front cover gently with the other to remove it.
Notes
When removing the cover, be careful that you don't touch
the drive units, and don't exert excessive force with any
tools.
There are magnets on the reverse side of the front cover. Do
not place a front cover close to objects that might be affected
by magnets, such as CRT TV, clock, magnetic card,
diskette, etc., after removing it.
NS-B310
Type .................... full-range acoustic suspension speaker system
Non-Magnetic shielding type
Driver.......................................8 cm (3-1/8”) cone full-range × 2
Impedance...............................................................................6 Ω
Frequency Response ............................80 Hz to 35 kHz (-10 dB)
to 50 kHz (-30 dB)
Nominal Input Power........................................................... 40 W
Maximum Input Power ...................................................... 120 W
Sensitivity ........................................................... 87 dB/2.83 V/m
Dimensions (W × H × D)............................ 107 × 200 × 127 mm
(4-3/16” × 7-7/8” × 5”)
Weight............................................................1.6 kg (3 lbs. 8 oz.)
NS-C310
Type ..........................2-way acoustic suspension speaker system
Non-Magnetic shielding type
Driver...................................... 6.5 cm (2-9/16”) cone woofer × 4
3 cm (1-3/16”) soft dome tweeter
Impedance...............................................................................6 Ω
Frequency Response ........................... 90 Hz to 45 kHz (-10 dB)
to 100 kHz (-30 dB)
Nominal Input Power........................................................... 40 W
Maximum Input Power ..................................................... 120 W
Sensitivity .......................................................... 90 dB/2.83 V/m
Crossover Frequency ......................................................... 6 kHz
Dimensions (W × H × D).............................. 440 × 94 × 125 mm
(17-5/16” × 3-11/16” × 4-15/16”)
Weight............................................................2.9 kg (6 lbs. 6 oz.)
Specifications subject to change without notice due to product
improvements.
Care should be taken not to exceed the input power values noted
above.
A speaker cable is not included with this model.
REMOVING THE FRONT
COVER
NS-B310
NS-C310
SPECIFICATIONS
Taking care of the speaker
When you wipe this unit, do not use chemical solvents (e.g.,
alcohol or thinners, etc.): this might damage the finish. Use a
clean, dry cloth. For difficult soils, dampen a soft cloth in
water, wring it out, and then wipe with the cloth.
English
5 En
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the
proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in
force in the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6.
Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.
4 Zh
安装前盖是为了保护扬声器,如有需要可将其拆下。
前盖由磁体固定。一手扶住扬声器,另一手轻拉前盖将其拆
下。
注意
当取下盖子时,小心不要触摸驱动单元,且不要用工具施
力。
前盖反面有磁体。取下前盖后,请勿将其靠近可能受磁体
影响的物体,如 CRT 电视机、时钟、磁卡、磁盘等。
NS-B310
类型 ....................... 全频声学悬挂式扬声器系统
非磁屏蔽
驱动单元 ......................... 8 cm 锥形全频 × 2
阻抗 ........................................... 6 Ω
频率响应 ................... 80 Hz 35 kHz (-10 dB)
50 kHz (-30 dB
标称输入功率 ................................... 40 W
最大输入功率 .................................. 120 W
灵敏度 ............................... 87 dB/2.83 V/m
尺寸 宽×高×深)............. 107 × 200 × 127 mm
重量 ......................................... 1.6 kg
NS-C310
类型 ......................... 2 分频声悬浮扬声器系统
非磁屏蔽
驱动单元 ................. 6.5 cm 锥形低音扬声器 × 4
3 cm 球顶高音扬声器
阻抗 ........................................... 6 Ω
频率响应 ................... 90 Hz 45 kHz (-10 dB)
100 kHz (-30 dB
标称输入功率 ................................... 40 W
最大输入功率 .................................. 120 W
灵敏度 ............................... 90 dB/2.83 V/m
分频频率 ..................................... 6 kHz
尺寸 宽 × 高 × 深).......... 440 × 94 × 125 mm
重量 ......................................... 2.9 kg
由于产品改进,若有规格变更恕不另行通知。
请小心不要超过上述注明的输入功率值。
此型号不附带扬声器电缆。
拆卸前盖
NS-B310
NS-C310
规格
爱护扬声器
擦拭本装置时,请勿使用化学溶剂 (例如酒精或稀释
剂等):可能损坏涂层。请使用清洁的干布。对于难以
清除的污点,用水蘸湿软布,拧干后进行擦拭。
©2008 Yamaha Corporation All rights reserved. Printed in Indonesia WP51950
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Yamaha NS-B310 Manuale del proprietario

Categoria
Parete
Tipo
Manuale del proprietario
Questo manuale è adatto anche per