Samsung MX-ST90B Sound Tower High Power Audio 1700W Manuale utente

MX-ST90B

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

comes with important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that a safety connection to electrical

earth (ground) is not required.

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : Rated voltage marked

with this symbol is AC voltage.

DC voltage : Rated voltage marked

with this symbol is DC voltage.

Caution. Consult Instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• 

not expose this appliance to rain or moisture.

• This product contains chemicals known to the

State of California to cause cancer and birth

defects or other reproductive harm.

CAUTION

• Do not expose this apparatus to dripping or



liquids, such as vases, on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

To avoid deterioration of water resistant

Check the following and use the unit correctly.

• Deformation or damage from dropping the

unit or subjecting it to mechanical shock may

cause deterioration of the water resistant.

• This unit does not have a design that is

resistant to water pressure. Use of the unit in

a location where high water pressure is

applied, such as in the shower, may cause a

malfunction.

• Do not pour high-temperature water or blow

hot air from a hair dryer or any other

applicance on the unit directly. Also never use

the unit in a place subject to high

temperatures, such as in a sauna or near a

heat source.

• Handle the cap with care. Port cover and AC

plug cover plays a very important role in

maintenance of the water resistant. When

using the unit, make sure that the cap is

closed completely. When closing the cap, be

careful not to allow foreign objects inside. If

the cap is not closed completely the water

resistant may deteriorate and may cause a

malfunction of the unit as a result of water

entering the unit.

• The product cannot be dumped to ensure it is

water resistant.

• IPX5 cannot be met when any JACK is

plugged in.

• In a state of electricity, IPX5 can be met when

the power cord passes through the cover

power slot and the cover power is completely

closed, otherwise, it does not.

POWER

ECHO 2VOL 2ECHO 1 VOL 1 MIC 2

USB1

(5V 2.1A)

USB2

(5V 0.5A)

AUX 1

MIC 1

ENG - iv

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power



sticker located on the rear of your product.

Install your product horizontally, on a

suitable base (furniture), with enough space

around it for ventilation (3~4 inches). Make

sure the ventilation slots are not covered. Do



equipment which may become hot. This unit

is designed for continuous use.

To fully turn off the unit, disconnect the AC

plug from the wall outlet. Unplug the unit if

you intend to leave it unused for a long

period of time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.



equipment creating strong magnetic or



the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,



FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code on the left. To see the

manual on your PC or mobile device, download

the manual in document format from

Samsung’s website.

(https://www.samsung.com/us/support/

downloads/)



without prior notice.

ENG - v

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control

(AAA batteries X 2) ------------------------- 4

02 Product Overview 5

Top Panel of the Sound Tower ------------------------- 5

Rear Panel of the Sound Tower ------------------------- 6

03 Connecting the Sound Tower 8

Connecting Electrical Power ------------------------- 8

Connecting Group Play Mode ------------------------- 9

04 Connecting an External Device 16

Connecting an External Device via Analogue Audio Cable ------------------------- 16

Connecting a mobile device via Bluetooth ------------------------- 17

Connecting a Samsung TV via Bluetooth ------------------------- 20

05 Connecting a USB Storage Device 22

Software Update ------------------------- 23

Connecting an Optional Microphone ------------------------- 24

06 Using the Remote Control 25

How to Use the Remote Control ------------------------- 25

How to use Sound Mode ------------------------- 28

How to use DJ Effect ------------------------- 29

ENG - vi

07 Using the Samsung Sound Tower App 30

Install Samsung Sound Tower App ------------------------- 30

Using the Samsung Sound Tower App ------------------------- 30

What you can do with Samsung Sound Tower App: ------------------------- 31

08 Trouble shooting 32

09 Licence 35

10 Open Source Licence Notice 36

11 Important Notes About Service 36

12 SpecicationsandGuide 37

 ------------------------- 37

ENG - 2

01 CHECKING THE COMPONENTS

Sound Tower Main Unit Remote Control /

Batteries (AAA batteries x 2)

Power Cord

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Rear of the Sound Tower Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

Carry the system

When moving the product, in order to avoid personal injury and/ or property damage, and achieve

water resistance, please see the illustrations below.

1. When moving the product, do not drag or pull the product from the ground without the wheels

sticking out.

2. Do not lift the set to prevent the set from injuring your feet.

ENG - 3

3. To move the set, perform the following steps.

• Press the self-locking switch of the wheels respectively to rotate the two wheels out of the

bottom of the set. When it clicks, it means that the wheels are adjusted in place.

POWER

Press the self-locking

switch

Rotate the wheels 180

degrees

The wheels were

adjusted to the front

• Use two hands to grab the handle on the back of the set and move it using the wheels as shown

below

Warning:

Use caution when moving the sound tower on an uneven surface to avoid injury or damage to the

unit or the surrounding environment.

ENG - 4

• After the set is moved, press the self-locking switch of the two wheels respectively to rotate

the wheels to the bottom of the set. When it clicks, it means that the wheels are adjusted in

place.

POWER

Press the self-locking

switch

Rotate the wheels 180

degrees

The wheel was rotated back

to the bottom of the set

4. The product should not be knocked over to ensure it keeps it’s water resistance.

Inserting Batteries before using the Remote Control

(AAA batteries X 2)

Slide the battery cover in the direction of the arrow

until it is completely removed. Insert 2 AAA

batteries (1.5V) oriented so that their polarity is

correct. Slide the battery cover back into position.

(the remote control does not support IPX5)

ENG - 5

02 PRODUCT OVERVIEW

Top Panel of the Sound Tower

BASS

󰟻

󰟶

󰟹

󰟷

󰟸

󰟺

󰟵󰟴

󰟳

󰟳Remote

Sensor

When operating the Sound Tower system, please aim the front of the remote control at

the remote sensor.

󰟴LED

indicator

Displays operating messages or current status of the Sound Tower system.

The information sources represented by each LED are as follows:

(BT) (USB1) (USB2) (AUX1) (AUX2)

󰟵Power Turns the Sound Tower on and off.

󰟶Light Press the (Light) button to turn the Lighting Mode on.

󰟷Source

Press to select a source connected to the Sound Tower.

Press and hold the (Source)

button for more than 5 seconds

to enter the

“SEARCHING TV” mode.

󰟸Play/Pause

• Play/Pause

Press the 



• Demo play

Press and hold the

button for more than 5 seconds to start the Demo play while

the system is turned on. 

90 seconds.

– Please be careful as it may play louder than the set volume.

󰟹Volume down Press the (Volume down) button to lower the volume.

󰟺Volume up Press the (Volume up) button to raise the volume.

󰟻BASS Press the BASS button to use the bass boost.

ENG - 6

Rear Panel of the Sound Tower

ECHO 2VOL 2ECHO 1 VOL 1 MIC 2

USB1

(5V 2.1A)

USB2

(5V 0.5A)

AUX 1

MIC 1

POWER

ECHO 2VOL 2ECHO 1 VOL 1 MIC 2

USB1

(5V 2.1A)

USB2

(5V 0.5A)

AUX 1

MIC 1

󰟳

󰟶

󰟷

󰟿 󰠀󰟽󰟼

󰟻 󰟾

󰟺

󰟹

󰟸

󰠁

󰟴 󰟵

󰟳Bluetooth

PAIRING

Press the PAIRING button to enter pairing mode, "PAIRING" LED on the rear

plane will blink quickly.

󰟴ADD STEREO Press the ADD STEREO button to connect to another same model Sound Tower

wirelessly.

󰟵GROUP PLAY Press the GROUP PLAY button to connect up to ten Sound Tower systems

wirelessly.

󰟶AUX1 Use an Audio (AUX) Cable (not supplied) to connect AUX1 jack on the main unit to

Audio Out on an external device.

󰟷ECHO1 You can give an echo effect to the sound from a connected microphone (MIC1) by

adjusting the ECHO1 knob.

󰟸VOL1 Use the VOL1 knob on the main unit to adjust the volume of a connected

microphone (MIC1).

󰟹MIC1 Connect your microphone to the MIC1 jack.

󰟺GROUP PLAY IN

Terminals

Use an Audio Cable (not supplied) to connect AUX2 (IN) terminals on the main unit

to Audio Out on an external analogue output device.

󰟻GROUP PLAY OUT

Terminals

Use an Audio Cable (not supplied) to connect GROUP PLAY (OUT) terminals on the

main unit to GROUP PLAY(IN) on another Sound Tower.

󰟼MIC2 Connect your microphone to the MIC2 jack.

󰟽VOL2 Use the VOL2 knob to adjust the volume of a connected microphone (MIC2).

󰟾ECHO2 You can give an echo effect to the sound from a connected microphone (MIC2) by

adjusting the ECHO2 knob.

ENG - 7

󰟿USB1 Connect a USB device to the USB1 or USB2 ports on the main unit.

If you connect your cell phone to the USB1 port, you can charge it.

• Press the (Source) button to select USB1 or USB2.

󰠀USB2

󰠁Power Connect the power cord to the Power jack and connect the other end of the power

cord to a wall socket to supply electrical power to the Sound Tower.

ENG - 8

03 CONNECTING THE SOUND TOWER

Connecting Electrical Power

Use the power cord to connect the Sound Tower to an electrical outlet in the following order:

Connect the power cord to the Sound Tower and then to a wall socket.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Rear of the Sound Tower)

• Water resistance can be met when the AC power cord is plugged in, but make sure that the cap is

completely closed. Laying the Sound Tower on its side may damage internal components and keep

the unit from being water resistant.

Rear of Sound Tower

POWER

Connecting

Electrical Power

ENG - 9

Connecting Group Play Mode

You can connect multiple audio systems in a wired group play mode to create a more interesting party

environment and to produce higher sound output.

Connecting the wired Group Play mode

1st

Sound Tower HOST

2nd

Sound Tower

Last

Sound Tower

AUX2 white LED on AUX2 white LED on

Continue these steps to

connect Sound Towers

until the last one is

connected.

󰟳󰟴 󰟵

RCA cable

(not supplied)

󰟳 Connect the analogue audio cable to the OUT(Group Play) of the HOST.



󰟴 Connect the analogue audio cable to the IN(AUX2) of 2nd Sound Tower and Set the source to AUX2.

󰟵 Set up Group Play by connecting all the systems using analogue audio cables.

Use the AUX or (Source) button to change the source to AUX2 for every Sound Tower except

the Sound Tower HOST.

• Set one Sound Tower as the HOST and any music played on it will be shared among any other

Sound Tower in the Audio group.

NOTES

• Analogue audio cables are not supplied.

• Depending on the length or characteristics of the cable, there may be a difference in operating

distance.

• Be sure to select the Audio In function on the last system.

• 

• To stop Wired Group Play:

– Remove analogue audio cable from the HOST

– Change to a source other than AUX2 on any Sound Tower in the group besides the HOST

– Turn off the HOST

• If the Wired Group Play function does not start:

– Check the connections.

– Ensure the audio cables are connected correctly.

ENG - 10

– Make sure that the HOST is turned on, and has a music source connected to it, and the volume

is not muted.

• Wired Group Play function does not work properly:

– Turn off the system. Then, turn it back on again to activate the function.

• When a microphone is connected to the HOST and being used, the MIC sound is output to all the

connected Sound Towers in the group.

Connecting wireless Group Play mode

You can connect multiple audio systems in a wireless group play mode to create a more interesting

party environment and to produce higher sound output.

Precondition

• When connecting a Sound Tower, make sure it is within 1 m distance.

• Cannot set the mode to Group Play mode when sound tower is connected to a TV.

• Before using Group Play mode, any sound towers should be taken out of Stereo mode.

POWER POWER POWER

SUB 1

Sound Tower

Continue these

steps to

connect Sound

Towers until the

last one is

connected.

LED Blinks Slow(15s)

Waiting to enter

pairing mode

LED Blinks Fast(30s)

SUB Connection

available

HOST

Sound Tower

Last(SUB)

Sound Tower

󰟳 󰟴 󰟵

󰟳 Press the GROUP PLAY button on the HOST Sound Tower and wait until the “GROUP PLAY” LED

switches from blinking slowly to blinking quickly. This Sound Tower will become the Sound Tower

HOST.





Group Play LED will blink quickly immediately.

󰟴 Press the GROUP PLAY button on the SUB Sound Tower, and it will begin searching for the HOST

while the “GROUP PLAY” LED blinks, and the LED will turn solid and the speaker will beep after

connecting to the HOST.

󰟵 If less than 20 minutes have passed since Group Play button was pressed, refer to Step 2 to

connect additional SUB. If 20 minutes have passed since Group Play was pressed, repeat steps 1

and 2 to connect additional SUB.

• Play music on the HOST Sound Tower. Sound outputs from all the connected systems.

ENG - 11

NOTES

• All the Sound Tower models can connect in Group Play mode.

• When “HOST” Sound Tower connects to a Samsung TV, the Group play mode will automatically

disconnect.

• Environmental conditions or other factors with connected devices may have an effect on playback

quality.

• If the light bar blinks pink and the speaker outputs a beeping sound, an error has occurred in the

Group Play mode connection. Try Step 1 and 2 again.

• The ADD STEREO button and PAIRING button on the SUB Sound Tower systems are not available

while in wireless Group Play mode.

• The ADD STEREO button on the HOST Sound Tower is not available while in wireless Group Play

mode.

• Bluetooth devices can search and connect with the HOST Sound Tower only, but the SUB cannot

connect to any Bluetooth device.

• If you power off or select any source other than BT on a SUB unit, the Group Play mode is

disconnected.

• This product does not support aptX audio stream with Wireless Group Play mode.

• 

• If Wireless Group Play does not work properly:

– Turn off the system. Then, turn it back on again to activate the function.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Sound Tower main unit - e.g., microwaves, wireless LAN devices, etc.

• When using the wireless Group Play mode function, sound from a connected microphone is only

output from the system to which the microphone is connected.

Disconnecting the wireless Group Play mode

1. Press and hold the GROUP PLAY button over 5 seconds (HOST or SUB).

• The speaker will beep and the Group Play LED will turn off.

2. If you select any source other than BT on the SUB units or turn off the HOST Sound Tower, the

Group Play mode is disconnected.

LED Indications

LED STATE Description

Green Blink Waiting for a wireless Group Play connection.

Solid The wireless Group Play connection was successful.

Red Solid There is an error with the wireless Group Play connection.

ENG - 12

Connecting Stereo Mode

Connect two Sound Tower and use them with a mobile device to enjoy stereo mode, to make a larger

listening area or to hear greater left and right audio separation.

Precondition

• To use the Stereo mode, both Sound Tower systems must be the same model.

• When connecting a Sound Tower, make sure it is within 1 m distance.

• If the sound tower is in Group Play mode, need to exit it before using Stereo mode.

• Cannot set the mode to Stereo mode when sound tower is connected to a TV.

Description LED Indicator Light Bar

POWER POWER

Left Speaker

MAIN Sound Tower

Right Speaker

SUB Sound Tower

Connecting

Cyan blink

Connected

Cyan blink once

Failed

Pink blink once

The initial connection

• After the initial connection is complete, if the ADD STEREO button is pressed on the MAIN or SUB

Sound Tower, the Left and Right Speaker are swapped.

1. Press the ADD STEREO buttons of the two Sound Towers. The LED blinks on the ADD STEREO

button.

2. When the connection is complete, each speaker beeps and the ADD STEREO LED turns solid. MAIN



• The MAIN Sound Tower outputs left channel sound and the SUB Sound Tower outputs right

channel sound.

• Play music by connecting your mobile device to the MAIN Sound Tower via Bluetooth. Sound is

output from both Sound Tower.

ENG - 13

NOTES

• Environmental conditions or other factors with connected devices may have an effect on playback

quality.

• If the ADD STEREO LED is solid red an error has occurred in the Stereo Group connection. Try steps

1 and 2 again.

• Remote Controller, BT PAIRING, GROUP PLAY and Source buttons on the SUB Sound Tower are

disabled while in Stereo Group mode.

• The GROUP PLAY button on the MAIN Sound Tower is not available while in Stereo Group mode.

• In any mode other than “BT” (ex. USB, AUX mode), music is played only from the MAIN Sound Tower

and not the SUB Sound Tower.

• The lighting colours between MAIN Sound Tower and SUB Sound Tower may vary.

• This product does not support aptX audio stream with Stereo mode.

• When using the wireless Stereo mode function, sound from a connected microphone is only output

from the system to which the microphone is connected.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Sound Tower main unit - e.g., microwaves, wireless LAN devices, etc.

Disconnecting the wireless Stereo mode

Press the ADD STEREO button (MAIN or SUB) for at least 5 seconds while the Stereo Group is

connected.

• The speaker will beep and the ADD STEREO LED will turn off.

ENG - 14

Using Stereo Mode with a Samsung TV

Connect two Sound Towers and use them with a Samsung TV to enjoy stereo mode, to cover a larger

listening area or to hear greater left and right audio separation.

Precondition

• To use the Stereo mode, both Sound Tower systems must be the same model.

• When connecting a Sound Tower or TV, make sure it is within 1 m distance.

• Cannot set to Stereo Mode with Samsung TV if the Sound Tower is already connected to a TV via

Bluetooth.

• If the sound tower is in Group Play mode, need to exit it before using Stereo mode.

LIGHT

PAIRING

TEMPO

USB AUX

EFFECT

DOWN UP

EFFECT

DJ

SOUND

MODE

󰟳 󰟴 󰟵

Left Sound Tower

(MAIN)

Left Sound Tower

(MAIN)

Right Sound Tower

(SUB)

Right Sound Tower

(SUB)

White LED on

AUX2 white LED on

󰟳 Connect two sound towers via stereo mode by pressing the ADD STEREO button on the two Sound

Towers.

󰟴 In “BT” mode, press the “AUX” button on the MAIN Sound Tower remote control for at least 5

seconds. The LED blinks on the ADD STEREO button.

󰟵 Connect a RCA cable to the OUT(Group Play) on the MAIN and AUX2 IN on the SUB as shown.

• When the connection is complete, the “ADD STEREO” LED will stop blinking and turn solid, the

speakers will beep, and the AUX2 LED on the SUB will turn on.

• The MAIN Sound Tower outputs the left channel sound and the SUB Sound Tower outputs the

right channel sound. Press the ADD STEREO button on the MAIN or SUB Sound Tower to swap

them between Left and Right.

• Connect a TV and MAIN Sound Tower via Bluetooth to play audio. Sound is output from both

Sound Towers.

ENG - 15

NOTES

• Analogue audio cables are not supplied.

• If the light bar blinks pink and the speakers beep, an error has occurred in the Stereo mode

connection. Repeat steps 1 through 3.

• In Stereo Group mode, the remote control, BT PAIRING, GROUP PLAY, and Source buttons on the

SUB Sound Tower are disabled.

• The GROUP PLAY button on the MAIN Sound Tower is not available in Stereo Group mode.

• If the Samsung TV supports a simple connection, the connection pop-up is automatically displayed

on the TV, and if you select “Yes”, it connects to the sound tower. If there is a previous connection

history between Samsung TV and Sound Tower, they will be connected without pop-up.

• The lighting colours may vary between the MAIN Sound Tower and the SUB Sound Tower.

• When a microphone is connected to the MAIN and being used, the MIC sound is output to the SUB.

Disconnecting Stereo mode connection

• Press the ADD STEREO button (MAIN or SUB) for at least 5 seconds after the Stereo Group is

connected. Sound tower will beep and the LED on the ADD STEREO button turns off.

La pagina sta caricando ...

Samsung MX-ST90B Sound Tower High Power Audio 1700W Manuale utente

Samsung MX-ST90B Sound Tower High Power Audio 1700W Manuale utente

in altre lingue