AvMap GeoPilot II Manuale utente

USER MANUAL

Via Caboto, 9

54036 Marina di Carrara - MS - ITALIA

E-mail: [email protected]

4

WARRANTY

AvMap warrants their GPS receiver and accessories to be free of defects in material and work-

manship for a period of two years from the date of original purchase. This warranty applies only

to the original purchaser of this product. In the event of a defect, AvMap, at its option, will

repair or replace the product with no charge to the purchaser for parts or labor. The repaired

or replaced product will be warranted for ninety (90) days from the date of return shipment, or

for the balance of the original warranty, whichever is longer.

PURCHASER’S REMEDY - Purchaser’s Exclusive Remedy under this written warranty or any

implied warranty shall be limited to the repair or replacement, at AvMap’s option, of any

defective part of the receiver or accessories which are covered by this warranty. Repairs under

this warranty shall only be made by an authorized AvMap dealer.

PURCHASER’S DUTIES - To obtain warranty service, the purchaser must return the receiver

or accessories post paid, with proof of the date of original purchase and purchaser’s return

address to AvMap, or an authorized AvMap representative. AvMap will not be responsible for

any losses or damage to the product incurred while the product is in transit or is being shipped

for repair. Insurance is recommended.

LIMITATION OF IMPLIED WARRANTIES - Except as set forth above, all other expressed or implied

warranties, including those of fitness for any particular purpose and merchantability, are hereby

disclaimed. Some states do not allow limitations on warranties, so the above limitation may

not apply to you.

EXCLUSIONS - This warranty does not cover the following: Installation, Finishes, Defects resulting

from installation. Any damage due to accident, resulting from inaccurate satellite transmissions.

Inaccurate transmissions can occur due to changes in the position, health, or geometry of a

satellite. Any damage due to shipping, misuse, negligence, tampering or improper use. Servicing

performed or attempted by anyone other than an authorized AvMap representative.

Attenzione! L’esposizione del display ai raggi ultravioletti può accorciare la vita dei

cristalli liquidi usati nel vostro plotter cartografico. Questo limite è dovuto alla tecnologia costruttiva

degli attuali display. Evitare inoltre che il display si surriscaldi per non causare una diminuzione di

contrasto che, in casi estremi, può rendere lo schermo completamente nero. Tale condizione è

comunque reversibile durante il raffreddamento.

Warning! Exposure of display to UV rays may shorten life of the liquid crystals used in

your plotter. This limitation is due to the current technology of the LCD displays. Avoid overheating

which may cause loss of contrast and, in extreme cases, a darkening of the screen. Problems which

occur from overheating are reversible when temperature decreases.

Achtung! Ultraviolette Strahlen können die Lebensdauer vom Flüssigkristalldisplay

verkürzen. Die derzeitige LCD-Technologie bedingt diese verkürzte Lebensdauer.

Überhitzung des Displays durch Sonneneinstrahlung führt zu einem Kontrastverlust und in extremen

Fällen sogar in eine Schwär zung des Bildschirmes. Bei sinkenden Temperaturen normalisiert sich

der Kontrast wieder und die Bildschirminformation wird wieder ablesbar.

Attention! L’exposition de votre écran LCD aux ultra-violets lors de soleil intense

réduira la durée de vie de l’afficheur de votre lecteur. Cette contrainte est liée à la technologie des

écrans LCD. Une augmentation trop importante de température peut obscurer des zones de votre

écran et le rendre ainsi inutilisable (non couvert par la garantie).

Aviso! La exposición de la pantalla a los rayos UV puede acortar la vida del cristal líquido

usado en su ploter. Esta limitación se debe a la tecnología actual de las pantallas LCD. Evitar que

la pantalla se caliente en exceso pues puede causar pérdida de contraste y, en caso extremo, la

pantalla puede quedar totalmente negra. Este problema revierte al enfriarse la pantalla

5

Warning!!!

A measure of knowledge by the user is required for proper and safe use of the chart plotter.

Read the User Manual and the Warranty completely.

Use Good Judgement

This product is an excellent navigation aid, but it does not replace the need for careful

pilotage and good judgement. Never rely solely on one means of naviga-tion.

Use Care to Avoid Inaccuracies

The Global Positioning System (GPS) is operated by the U.S. Government, which is solely

responsible for the accuracy and the maintenance of GPS. Certain conditions can make the

system less accurate.

Accuracy can also be affected by poor satellite geometry.

The accuracy of position fixes is subject to changes in accordance with the Department of

Defense civil GPS user policy and the Federal Radionavigation Plan.

Cleaning Procedure for the Chartplotter Screen

Cleaning of the chartplotter screen is a very important operation and must be done carefully.

Since the surface is covered by a antireflective coating, the procedure for cleaning all the

surfaces can be performed using the following procedure: You need a tissue or lens tissue

and a cleaning spray containing Isopropanol (a normal spray cleaner sold for the PC screen,

for example PolaClear by Polaroid). Fold the tissue or lens tissue into a triangular shape,

moisten the tip and use the index finger behind a corner to move the tissue across the

surface, in overlapping side to side strokes. If the tissue is too wet, a noticeable wet film will

be left in its path and you will need to repeat the process. If too dry, the tissue won’t glide

easily, and may damage the surface.

No part of this User Manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying and recording , for any purpose other than the

purchaser’s personal use without the written permission of AvMap.

6

7

TABLE OF CONTENTS

1 IntroductIon

1.1 FEATURES 12

1.1.1 Specifications 12

1.2 BASIC 14

1.3 FLYING START 15

1.3.1 The Moving Map 15

1.3.2 The Main Menu 15

1.3.3 Moving Map Functions 15

1.3.4 Moving Map Icons 16

1.3.5 Course Predictor 16

1.3.6 GoTo 17

1.3.7 Database 17

2 the BasIcs

2.1 THE KEYBOARD 18

2.2 TURNING THE GEOPILOT II ON/OFF 19

2.2.1 Turning On 19

2.2.2 Turning Off 19

2.3 CHANGING BRIGHTNESS & CONTRAST 19

2.4 SELECTING THE LANGUAGE 19

2.5 EXTERNAL CONNECTIONS 20

2.5.1 Down Or Up-load Flight Plans & Tracks 20

2.5.1.1 Download/Upload Waypoints 20

2.5.1.2 Download/Upload Flight Plan 20

2.5.1.3 Download Track 20

2.6 SYSTEM SETUP OPTIONS 20

2.7 DATA ENTRY 21

3 the MovIng Maps

3.1 OPERATING MODES 22

3.1.1 Cursor Mode 22

3.1.2 Auto Home (Screen Amplifier) 22

3.1.3 Auto Zoom Mode 22

3.2 DATA WINDOW 23

3.3 AUTOMATIC INFO 23

3.4 CURSOR OR POSITION MODE 23

3.4.1 Airspace Information 23

3.4.2 Full Information 24

3.4.3 Project Radial 24

3.4.4 A - B Function 24

3.4.5 Waypoint Handling 25

3.4.6 Flight Plan 25

3.5 MOVING MAP MENU 26

3.5.1 Viewed Fp 26

3.5.2 Auto Position Mode 27

3.5.3 Data Window mode 27

3.5.4 Setup Data Fields 28

3.5.5 Default Datafields 28

3.5.6 Map Orientation 28

8

3.5.7 Map Presentation Settings 29

3.5.8 Automatic Information 29

3.5.9 Rangerings 29

3.5.10 Vfr, Airspace, Land, Marine And Other Settings 30

3.5.10.1 VFR Settings 30

3.5.10.2 Airspace Settings 30

3.5.10.3 Land Settings 31

3.5.10.4 Marine Settings 31

3.5.10.5 Other Settings 32

3.5.11 Terrains 32

3.5.11.1 Terrain “ON” 32

3.5.11.2 Terrain “OFF” 32

3.6 MAP PRESENTATION MENU 32

3.6.1 Generic 33

3.6.2 TAWS 33

3.6.3 Selective Display Settings 34

3.6.4 POI Settings 35

4 navIgatIon & LocatIon

4.1 NAVIGATION & LOCATION DATA 36

4.2 SAVE CURRENT FIX AS USER WAYPOINT 37

5 the hsI screen

5.1 HSI DESCRIPTION 38

5.2 HSI MENU 38

5.2.1 Add Mark Under Fix 38

5.2.2 Setup Datafields 39

5.2.3 Default Datafields 39

5.2.4 Compass Orientation 39

6 FLIght pLan

6.1 VIEWED FLIGHT PLAN 40

6.2 CREATING A FLIGHT PLAN FROM THE DATABASE 40

6.3 ACTIVATE & DEACTIVATE A FLIGHT PLAN 41

6.4 NAMING A FLIGHT PLAN 42

6.5 CLEAR A FLIGHT PLAN 42

6.6 REVERSE A FLIGHT PLAN 42

6.7 GOTO FLIGHT PLANS 42

6.7.1 GoTo - Database Mode 42

6.7.2 GoTo - Moving Map Mode 43

6.7.3 GoTo - Quick Info 43

6.8 NEAREST SEARCH FOR GOTO FLIGHT PLAN ACTIVATION 43

7 the gLoBaL posItIonIng systeM

7.1 GPS PAGE 45

7.2 GPS RECEIVER SPECIFICATIONS 45

7.3 HOW GPS WORKS 46

7.3.1 Accuracy 46

7.3.2 WAAS 46

7.3.3 Differential GPS 46

7.3.4 Monitoring & Controlling The GPS 47

9

7.3.5 GPS Information Sources 47

8 WaypoInt & dataBase

8.1 USER WAYPOINTS – MOVING MAP 48

8.1.1 Creating User Waypoints – Moving Map 48

8.1.2 Saving Present Position – Moving Map Methods 48

8.1.3 Editing User Waypoints – Moving Map Methods 48

8.1.4 Deleting User Waypoints – Moving Map Methods 49

8.2 USER WAYPOINTS – DATABASE METHODS 49

8.2.1 Creating User Waypoints – Database Methods 49

8.2.2 Editing User Waypoints – Database Methods 49

8.2.3 Deleting User Waypoints – Database Methods 49

8.3 DATABASE 49

8.3.1 Database Menu 49

8.3.1.1 Selecting Database Search Fields 50

8.3.1.2 Displaying Sunrise and Sunset Information 50

8.3.2 File Manager 50

9 approach data procedures

9.1 APPROACH FROM THE MOVING MAP 52

9.2 APPROACH FROM FLIGHT PLAN DATABASE 52

9.3 SELECT APPROACH FOR GOTO 53

10 caLcuLator

10.1 COUNTDOWN TIMER 54

10.2 ELAPSED TIMER 54

10.3 TRIP COMPUTER 55

10.4 VERTICAL NAVIGATION 55

10.5 WIND CALCULATION 57

10.6 FUEL CONSUMPTION 58

11 the checkLIsts

11.1 ENGINE START 60

11.2 GROUND CHECK 60

11.3 PRE TAKE-OFF 61

11.4 CRUISE IN FLIGHT 61

11.5 LANDING 61

12 sIMuLator

12.1 SIMULATING STRAIGHT MODE 62

12.2 SIMULATING ROUTE MODE 62

12.3 TURNING THE SIMULATOR OFF 63

13 the coMMunIcatIon Menu

13.1 WAYPOINTS UPLOAD/DOWNLOADS 64

13.2 FLIGHT PLAN UPLOAD/DOWNLOAD 64

13.3 TRACK DOWNLOAD 65

10

14 the systeM set-up Menu

14.1 GENERAL SET-UP 66

14.1.1 Beeper 66

14.1.2 Scale Format 66

14.1.3 Language 67

14.1.4 Military Frequency 67

14.1.5 Airspaces Level 67

14.1.6 Terrain Legend 67

14.2 FIX SET-UP 67

14.2.1 Fix Source 67

14.2.2 Differential Correction Source 67

14.2.3 Fix Symbol 68

14.2.4 Static Navigation 68

14.2.5 Course Predictor 68

14.2.6 Head Up Response 68

14.3 ALARM SET-UP 68

14.3.1 Arrival Alarm Radius 68

14.3.2 XTE Alarm Range 69

14.3.3 Waypoint Alarm Radius 69

14.3.4 TAWS Alarm 69

14.3.5 Airspace Ahead Alarm 69

14.3.6 Event Log 70

14.3.7 Clear Event Log 70

14.4 TRACK SET-UP 70

14.4.1 Track Display 70

14.4.2 Track Line 70

14.4.3 Track Width 70

14.4.4 Track Color 70

14.4.5 Track Recording Step 70

14.4.6 Clear Track 71

14.4.7 Remaining Track 71

14.5 UNITS SET-UP 71

14.5.1 Distance Unit 71

14.5.2 Speed Units 71

14.5.3 Altitude Unit 71

14.5.4 Depth Unit 72

14.5.5 Fuel Unit 72

14.5.6 Vertical Speed 72

14.5.7 Temperature 72

14.5.8 North Reference 72

14.5.9 Coordinate System 72

14.6 DATE & TIME SET-UP 73

14.6.1 Time Format 73

14.6.2 Local Time Difference 73

14.6.3 Data Format 73

14.7 COLORS SET-UP 73

14.7.1 Data Window Colors 74

14.8 CLEAR USER DATA 74

14.9 CLEAR ALL RADIALS 74

14.10 FACTORY DEFAULTS 74

15 operatIng requIreMents

15.1 SECURING THE GEOPILOT II 75

11

15.2 DIMENSIONS 75

15.3 TROUBLESHOOTING 76

15.3.1 Power 76

15.3.2 GPS Fix 76

15.3.3 When Nothing Else Works 76

15.3.4 Customer Support 77

15.4 SYSTEM TEST 77

15.4.1 RAM Menu 78

15.4.2 C-CARD Menu 78

15.4.3 Serial Ports 78

APPENDIX A - TERMS 79

APPENDIX B - MAP DATUM 82

APPENDIX C - ICAO CODES 83

APPENDIX D - C-MAP AV. CARTRIDGE OPTIONS 89

APPENDIX E - C-MAP DATA TRANSFER 90

12

1 INTRODUCTION

If you have not used a GPS Charting System before and intend to use your Geopilot II for

navigating, we suggest that you read this User Manual and make sure you are familiar with its

contents. Throughout this User Manual, the keys are shown in capital letters enclosed between

single inverted commas, for example ‘MENU’. Menu operations are in bold characters listed by

keys sequence with the menu names enclosed between quotes, for example ‘MENU’ 1 sec. +

“SYSTEM SETUP” + ‘ENT’ + “FIX SETUP” + ‘ENT’ means: press and hold down the ‘MENU’ key

for 1 second, using the cursor key selects the System Setup menu, press ‘ENT’, using the cursor key

selects the Fix Setup menu and then press ‘ENT’.

1.1 FEATURES

This electronic charting system integrates the remarkable accuracy of a GPS receiver with a detailed

moving map into a single, easy-to-use, computerized electronic map system. The Geopilot II

contains a built-in base map with coast/shorelines, names of states, major cities, highways, lakes

and rivers.

When the Geopilot II is first opened, please check it for the following contents:

• SD (2 GB) with Aeronautical+Jeppesen Maps (inserted in the slot on the left side of the unit)

• Power cord

• Suction cup mount

• Quick guide

Optional Accessories:

• PC/Data cable

If any parts are missing contact the dealer where you purchased it immediately: additional C-MAP

NT+ Compact Flash (cartography and aeronautical data cards) and mounting hardware options are

available through your local dealer.

For additional information, visit our web site at: www.avmapnavigation.com

1.1.1 Specifications

Main Characteristics

Recordable Individual points

• Waypoints:1000

• Type of User Waypoint Icons:16

Flight Plans

• Flight Plans: 15

• Max Waypoints per Flight Plan: 100

Tracking

• Tracks: 1

• Track Colors: 7

• Points per Track: 5000

• Step by Distance: Auto, 20, 100, 500 Mt, 1Km; 5, 30 Sec, 1 Min

13

Cartographic Functions

• Worldwide Background

• Built-in Continental Cartography

• Coordinates System (DDD MM SS, DDD MM.mm, DDD MM.mmm, UTM, OSGB, MGRS)

• North Reference

• Auto Zoom

• Map Presentation (Aero+Terrestrial, Aeronautical, Marine)

• POI Settings

• Selective and cycled Display

• VFR (Airports, VOR, NDB, Intersections, Vertical Obstructions, Aero Objects Id, Enroute

Communications)

• Airspace (Controlled Areas, Restricted Areas, FIR & UIR, MORA)

• Land (Roads, Road Labels, Railroads, City Names, Rives and Lakes, Cultural Features, Natural

Features, Landmarks, POI Objects)

• Marine (Lights, Chart Boundaries, Bathymetric & Soundings, Bathymetric & Soundings Range,

Depth Area Limit, Navigational Aids, Attention Areas, Tracks & Routes)

• Other Settings (User Points, Objects Overlap, Lat/Lon Grid)

Fix Functions

• DGPS

• WAAS

• Fix Symbol user selectable (Standard, Plane, Helicopter, Car)

• Static Navigation

• Course Predictor

• Map Orientation (Track-up, Course-up, North-up)

• Projected Radial

• A-B measurement

Data Page Options

• Nav/Location

• HSI Page

• Flight Plan

• GPS Page

• About Page

Special Functions

• Automatic Info (Aero+Terrestrial, Aeronautical, Terrestrial, Marine)

• Nearest search

• Direct-To navigation

• Date and Time Format

• Astronomic Data Calculation (Sun/Moon Info)

• Distance Unit selection (KM, NM, SM)

• Speed Unit selection (MPH, KTS, KMH)

• Altitude Unit selection (FT, FL, MT)

• Depth Unit selection (FT, FM, MT)

• Fuel Unit selection (GAL, LIT, LB, KG, BGAL)

• Descent Rate selection (FT/MIN, M/S, DEG)

• Temperature Unit (C/F)

• Alarms handling (Arrival, XTE, Waypoint Alarm Radius, Airspace)

• Database(Airports, VOR, NDB, Intersections, POI objects, User Waypoints, File Manager)

• Calculator (Countdown Timer, Elapsed Timer, Trip Computer, Vertical Navigation, Wind

Calculation, Fuel Consumption)

• Simulation mode (Speed, Heading)

• Checklists (Engine Start, Ground Check, Pre Take-Off, Landing)

• Communications (Waypoints Upload/Download, Flight Plan Upload/Download, Track Upload/

14

Download)

Interface

• Serial I/O port

Physical Characteristics

Size

• Ultra-sleek 100x139.7 x 35.4 cm

Weight

• Under 1lib (390 g)

LCD display

• Color 5” LCD TFT ultra bright, sun viewable

• resolution 320x240 pixels

Power Supply

• 10-35 V (cigarette plug power cable)

• Operating Temperature Range 32°F to 131°F (0°C to 55°C)

Storage Temperature

• -13°F to 158°F (-25°C to 70°C)

Keyboard

• Backlighted, silicon rubber

1.2 BASIC

The GEOPILOT2 is controlled by using 6 keys and the cursor key. As you press a key, a single audio

beep confirms the key action; three rapid beeps indicates that no response is available.

NEAR Key - For quick access to the GPS status press and hold 1 sec the ‘NEAR’ key. The Brightness

and contrast will appear; the GPS status and current time are displayed at the bottom of this box.

Fig. 1.2 - The Geopilot II

15

1.3 FLYING START

These pages provide a very brief overview of several of the Geopilot II’s important features, the

Main Menu, the Moving Map, GoTo flights and locating a Waypoint in the Database. It does not

replace the User Manual, which should be read to get the fullest possible use from your Geopilot

II.

Note

The Geopilot II is an aid to navigation. It does not replace paper charts and good judgement.

1.3.1 The Moving Map

Before starting, connect the Geopilot II to power and place the antenna with a clear view of the sky.

Turn On the unit pressing ‘NEAR’. Press ‘ENT’ to exit from the Warning page and enter the Moving

Map mode. The Moving Map is the default state displaying the Moving Map screen and the Data

Window. The Data Window contains navigation information boxes (See Chapter 3 for details on

Moving Map mode).

Note: If no Fix is available, red dashed cross is displayed over the map for increased Pilot

Awareness.

To Change the Scale of the Moving Map

Use ‘+’ and ‘-’ to change the map display scale.

To Select Position

Use the cursor key to scroll to the location you want.

1.3.2 The Main Menu

From Moving Map press ‘MENU’ for 1 second to display the Main Menu:

Fig. 1.3.2 - Main Menu

1.3.3 Moving Map Functions

The Moving Map operates in Auto Home, Auto Zoom, and Cursor Mode. The screen will behave

differently based on the mode of operation selected. The Auto Home mode will allow the user to

16

pan away from his present position to view other parts of the map, and return to present position

automatically when no buttons are pushed for a pre-determined amount of seconds. Auto Zoom

mode will keep your present position, and your destination in the screen at all times. The screen

will automatically zoom in as you get closer. To shut off this function, simply select OFF.

The Cursor Mode (OFF Selected) will allow you to move the map to any position to view data or

details. To return to your present position, just press ‘ESC’ while in moving map.

The control for these functions is found in the Moving Map Menu, under Auto Position Mode.

1.3.4 Moving Map Icons

The following icons are displayed on the Moving Map to represent Waypoints, navigation aids and

airports.

Fig. 1.3.4 - Moving Map Icons

1.3.5 Course Predictor

Indicates the projected position at the set time interval if the current speed and heading are kept.

This allows the pilot to correct for wind drift, in real time, right from the moving map. To select

course predictor:

> ‘MENU’ 1 sec. + “SYSTEM SETUP” + ‘ENT’ + “FIX SETUP” + ‘ENT’ + “COURSE

17

PREDICTOR” + ‘ENT’

1.3.6 GoTo

GoTo sets a 1-leg course from the present position to any location or selected Waypoint. To activate

a GoTo Flight Plan move the cursor to the desired location or Waypoint and press ‘GOTO’. The

GoTo menu box will open enabling you to activate the current cursor position or search the

Database for a specific object to fly to. To activate the current cursor position, highlight “CURSOR”

and press ‘ENT’. To activate a GoTo Flight Plan to a specific Database item, select the category and

press ‘ENT’. Select the database item and press ‘GOTO’ again to activate.

To deactivate, press ‘GOTO’ and select “DEACTIVATE”.

1.3.7 Database

The Database function allows the user to access information stored in the data cartridges on

Airports, VOR’s, NDB’s, Intersections and User Waypoints. Searching the Database allows the user

to activate GoTo Flight Plans and locate the item on the map. There are two methods of accessing

the Database information. The first is through the Database function within the Main Menu and the

second is directly from the Moving Map display (see Chapter 3).

18

2 THE BASICS

This chapter provides general information about the functions of the keys and entering data.

2.1 THE KEYBOARD

The GeoPilot2 has 7 keys, which access and control features. Some keys perform different tasks

based on the operation mode. A quick key guide is displayed at the bottom of many menus for easy

reference. Below we indicate the keys in capital letters enclosed between single inverted commas,

for example ‘MENU’. When a key, for example ‘MENU’, must be pressed and held down for more

than 1 second it is shown as ‘MENU’ 1 sec.

The Near key

‘NEAR’: press and hold to turn the GeoPilot2 On.

‘NEAR’ 3 sec.: once the GeoPilot has been turned On turns the GeoPilot Off.

‘NEAR’: (immediately release!) Displays a list of the 20 nearest objects, including private airports

which contain runways of at least 500 ft. in lenght, relative to fix position or cursor position if no

fix is available.

‘NEAR’: 1 sec once the GeoPilot2 has been turned On displays the Brightness and the Contrast

Menu.

The GoTo key

Activates a Flight Plan to the cursor position (in Moving Map) or to selected object (in other

modes).

GOTO 1 sec.: allows the user to quickly filter mapping information on the display. There are three

Cycle modes selectable and holding GOTO shifts from one to the other in succession. The default

Cycle is the Cycle 1 that normally activates all features to be visible on the display.

To set user preferences for the Cycle Key:

‘MENU’ + “SELECTIVE DISPLAY” + ‘ENTER’

The Cycles appear in the first three columns and are labeled 1, 2 and 3. In order to adjust at which

Cycle features appear, use the Cursor Control key to highlight an item and hit ‘ENTER’ to remove

the item from appearing. Hit ENTER again to check the item so that it will appear on the display

when that Cycle is activated. Continue to use this procedure to activate features in Cycles 1 - 3 as

desired.

The - key

Shows less detail of a larger area by changing the chart scale and zooming out on the map display.

The cursor key

Moves the cursor on the Moving Map, quickly and accurately. Also scrolls to the desired options

in menu page(s).

If pressed on the center it works as an ‘ENT’ key, it selects the desired option or confirms selection.

Also opens the Cursor/Position Menu.

The + key

Shows more detail of a smaller area by changing the chart scale and zooming in on the map display.

If pressed outside the Moving Map it can be used as an ‘ENT’ key

The Esc key

Rejects an action, closes a window or activates Home or Auto Zoom mode.

19

‘Esc’ 3 sec. on the moving map changes the position of the fix icon: one configuration displays

the fix icon on the 20% central area of the Moving Map and the other on the exact center of the

screen.

The Menu key

‘MENU’: selects the Moving Map Menu.

‘MENU’: press & hold for 1 seconds: opens the Map Presentation Menu

The menu enables the user to select between generic representation mode, three TAWS modes

(auto, low sep and high sep) and two Weather modes (North America only)

2.2 TURNING THE GEOPILOT II ON/OFF

Before powering On the Geopilot II, check for the correct voltage (10-35 Volt DC).

2.2.1 Turning On

Press and hold ‘NEAR’ for 1 second. The Geopilot II emits one rapid beep sound and a Title page

containing information about the Product name, Software version, library version and cartridges

installed is displayed. This data can also be viewed in the “About” page in the “Main Menu”.

Fig. 2.2.1 - Title page

After a few seconds the Warning page is displayed, reminding you that the Geopilot II is an aid to

navigation and should be used with appropriate prudence. The electronic charts are not intended

to substitute for the official charts. Press ‘ENT’ to open the Moving Map screen.

2.2.2 Turning Off

‘NEAR’ 3 sec.: a countdown timer appears on the screen, if you release the key before the

countdown timer reaches zero, the Geopilot II will remain On.

2.3 CHANGING BRIGHTNESS & CONTRAST

Press and hold 1 sec ‘NEAR’ to adjust the brightness and the contrast of the display and keyboard

(do not press and hold the key or the “power-off ” message will be displayed!).

To increase/decrease the brightness use respectively up/down cursor key. Similarly, to increase/

decrease the contrast use left/right cursor key. In addition the Time and the GPS State are shown.

2.4 SELECTING THE LANGUAGE

It is possible to select the language in which the information is displayed (for screen labels, menus

and options, but it does not affect the map information). The default setting is English.

> ‘MENU’ 1 sec. + “SYSTEM SETUP” + ‘ENT’ + “GENERAL SETUP” + ‘ENT’ +

“LANGUAGE” + ‘ENT’

20

Choose the language you want and press ‘ENT’ again to confirm.

2.5 EXTERNAL CONNECTIONS

2.5.1 Down Or Up-load Flight Plans & Tracks

The Geopilot II can also send and receive Flight Plans from the AvMap Flight Planner or another

device compatible with it through the serial port (the USB port is for factory use only). This requires

an optional data cable that can be purchased from your avionics dealer or AvMap/Navigation for a

proper connection to the device (see following figures).

2.5.1.1 Download/Upload Waypoints

The Download Waypoint function allows you to send the current Waypoints to the serial port using

the NMEA0183 $WPL sentence (see Appendix E):

> ‘MENU’ 1 sec. + “COMMUNICATIONS” + ‘ENT’ + “WAYPOINTS DOWNLOAD” +

‘ENT’

The Upload Waypoint function allows you to receive Waypoints from the serial port using the

NMEA0183 $WPL sentence (see Appendix E):

> ‘MENU’ 1 sec. + “COMMUNICATIONS” + ‘ENT’ + “WAYPOINTS UPLOAD” +

‘ENT’

2.5.1.2 Download/Upload Flight Plan

The Download Flight Plan function allows you to send the current Flight Plans to the serial port

using the NMEA0183 $WPL and $RTE sentences (see Appendix E):

> ‘MENU’ 1 sec. + “COMMUNICATIONS” + ‘ENT’ + “FLIGHT PLAN DOWNLOAD”

+ ‘ENT’

The Upload Flight Plan function allows you to receive Flight Plans from the serial port using the

NMEA0183 $WPL and $RTE sentences (see Appendix E):

> ‘MENU’ 1 sec. + “COMMUNICATIONS” + ‘ENT’ + “FLIGHT PLAN UPLOAD” +

‘ENT’

The received Flight Plan is saved in the current Flight Plan. If the current Flight Plan contains data

the user should be asked to confirm the action (overwriting the existing Flight Plan) or choose

another Flight Plan.

2.5.1.3 Download Track

The Download Track function allows you to send Track data from the serial port using the CMAP

Proprietary NMEA0183 $PCMPT sentence (see Appendix E):

> ‘MENU’ 1 sec. + “COMMUNICATIONS” + ‘ENT’ + “TRACK DOWNLOAD” + ‘ENT’

2.6 SYSTEM SETUP OPTIONS

You may select how the Geopilot II displays primary information (such as how time is displayed)

from the System Setup Menu.

> ‘MENU’ 1 sec. + “SYSTEM SETUP” + ‘ENT’

Refer to Chapter 14 for information about the System Setup Menu.

La pagina sta caricando ...

AvMap GeoPilot II Manuale utente

AvMap GeoPilot II Manuale utente

in altre lingue