Axis P3363-VE Manuale utente

INSTALLATION GUIDE

ENGLISH DEUTSCH ITALIANO ESPAÑOL

FRANÇAIS

AXIS P3363-VE Network Camera

AXIS P3364-VE Network Camera

AXIS P3364-LVE Network Camera

About this Document

This document includes instructions for installing AXIS

P3363-VE, AXIS P3364-VE and AXIS P3364-LVE on your

network. Previous experience of networking will be beneficial

when installing the product.

Legal Considerations

Video and audio surveillance can be prohibited by laws that vary

from country to country. Check the laws in your local region

before using this product for surveillance purposes.

This product includes one (1) H.264 decoder license. To purchase

further licenses, contact your reseller.

Trademark Acknowledgements

Apple, Boa, Bonjour, Ethernet, Internet Explorer, Linux,

Microsoft, Mozilla, Real, SMPTE, QuickTime, UNIX, Windows,

Windows Vista and WWW are registered trademarks of the

respective holders. Java and all Java-based trademarks and

logos are trademarks or registered trademarks of Oracle

and/or its affiliates. UPnPTM is a certification mark of the

UPnPTM Implementers Corporation.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to fulfill applicable

standards for:

Radio frequency emission when installed according to the

instructions and used in its intended environment.

Immunity to electrical and electromagnetic phenomena when

installed according to the instructions and used in its intended

environment.

USA - Using an unshielded network cable (UTP): This equipment

has been tested using an unshielded network cable (UTP) and

found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

Using a shielded network cable (STP): This equipment has also

been tested using a shielded network cable (STP) and found to

comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Canada - This Class B digital apparatus complies with Canadian

ICES-003.

Europe - This product fulfills the requirements for

immunity according to EN 55024 office and commercial

environments.

This product fulfills the requirements for immunity according to

EN 61000-6-1 residential, commercial and light-industry

environments.

This product fulfills the requirements for immunity according to

EN 61000-6-2 industrial environments.

Australia - This digital equipment fulfills the requirements for

RF emission according to the Class B limit of AS/NZS CISPR 22.

Equipment Modifications

This equipment must be installed and used in strict accordance

with the instructions given in the user documentation. This

equipment contains no user-serviceable components.

Unauthorized equipment changes or modifications will

invalidate all applicable regulatory certifications and approvals.

Safety

This product complies with EN/IEC/UL 60950-1 and

EN/IEC/UL 60950-22, Safety of Information Technology

Equipment.

EN 50121-4

This product fulfills the requirements for emissions and

immunity according to EN 50121-4 railway applications.

Liability

Every care has been taken in the preparation of this document.

Please inform your local Axis office of any inaccuracies or

omissions. Axis Communications AB cannot be held responsible

for any technical or typographical errors and reserves the right

to make changes to the product and documentation without

prior notice. Axis Communications AB makes no warranty of any

kind with regard to the material contained within this

document, including, but not limited to, the implied warranties

of merchantability and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible for

incidental or consequential damages in connection with the

furnishing, performance or use of this material.

RoHS

This product complies with both the European RoHS

directive, 2002/95/EC, and the Chinese RoHS

regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member states.

The WEEE marking on this product (see right) or its

documentation indicates that the product must not be disposed

of together with household waste. To prevent possible harm to

human health and/or the environment, the product must be

disposed of in an approved and environmentally safe recycling

process. For further information on how to dispose of this

product correctly, contact the product supplier, or the local

authority responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly. This

product should not be mixed with other commercial waste. For

more information, visit www.axis.com/techsup/commercial

waste

Support

Should you require any technical assistance, please contact your

Axis reseller. If your questions cannot be answered immediately,

your reseller will forward your queries through the appropriate

channels to ensure a rapid response. If you are connected to the

Internet, you can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database. Search

by product, category, or phrases

• report problems to Axis support by logging in to your private

support area.

Japan - B

Korea -

ࢇ̛̛Еɼࢽࡈ%̗ࢷ࢕ળࢶଢ̛̛Ի۰

࣯Իɼࢽ߾۰یࡈଜЕʨࡶּࢶࡳԻଜֲֻҘ

एࠇ߾۰یࡈଟܹ࢑ݡТЬ

ENGLISH

Safeguards

Please read through this Installation Guide carefully before installing the Axis product. Keep the

Installation Guide for further reference.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure. Do not install the

product on unstable brackets, unstable or vibrating surfaces or walls, since this could cause

damage to the product.

• Only use applicable tools when installing the Axis product; excessive force could cause

damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Use only accessories that comply with technical specification of the product. These can be

provided by Axis or a third party.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for ser-

vice matters.

• This Axis product shall be used in compliance with local laws and regulations.

• The Axis product should be installed by a trained professional. Observe relevant national

and local regulations for the installation.

Transportation

• When transporting the Axis product, use the original packaging or equivalent to prevent

damage to the product.

Battery Replacement

This Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time

clock (RTC). Under normal conditions this battery will last for a minimum of 5 years. Low battery

power affects the operation of the RTC, causing it to reset at every power-up. A log message will

appear when the battery needs replacing. The battery should not be replaced unless required!

If the battery does need replacing, please contact www.axis.com/techsup for assistance.

• Dispose of used batteries according to the manufacturer's instructions.

• Risk of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent battery, as recommended by the manufacturer.

Dome Cover Cleaning

• Be careful not to scratch or damage the dome cover. Keep the protective plastic on the

dome cover until the installation is complete. Do not clean a dome cover that looks clean to

the eye and never polish the surface. Excessive cleaning could damage the surface.

• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free

neutral soap or detergent with water and a soft cloth. Rinse well with clean lukewarm

water. Dry with a soft cloth to prevent water spotting.

• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct

sunlight or at elevated temperatures.

• Domes for L products come with an anti-scratch surface. Avoid leaving finger prints on the

dome surface since this might impair image quality.

AXIS P33-VE Network Cameras Installation Guide Page 5

ENGLISH

AXIS P3363-VE/P3364-VE/P3364-LVE

Network Camera Installation Guide

Follow these instructions to install the network camera

1. “Package contents” on page 5

2. “Hardware overview” on page 6

3. “Install the hardware” on page 7

4. “Access the video stream” on page 10

5. “Adjust the Lens” on page 10

6. “Complete the installation” on page 11

Notes:

• Before you begin, make sure that the package contents, power supply, and the required cables, tools, and

documentation are available. See Package contents below.

• This network camera is intended to operate with PoE; if not available use Axis PoE Midspan 1 port (not

included)

Package contents

Item Models/variants/notes

Network camera

with heating module

AXIS P3363-VE

AXIS P3364-VE

AXIS P3364-LVE

Mounting bracket

Dome covers Clear transparent cover (not for AXIS P3364-LVE)

Smoked transparent cover

Weather shield Not applicable for AXIS P3364-LVE

Labels 2 adhesive serial no. labels

Mounting kit Resitorx screw driver, 2 long screws, drill template, 5-meter network cable

with gasket, 1 gasket, terminal block connector

CD Installation and Management Software CD

Printed Materials Installation Guide (this document)

AVHS Authentication key

Optional accessories Threaded adaptor with cable shield

See www.axis.com for information on available accessories

Page 6 AXIS P33-VE Network Cameras Installation Guide

Hardware overview

Dimension (HxW)

AXIS P3363-VE/AXIS P3364-VE/AXIS P3364-LVE = 110 x 179 x 179 mm (4.33 x 7.05 x 7.05")

Weight

AXIS P3363-VE/AXIS P3364-VE = 1.5 kg (3.2 lb.)

AXIS P3364-LVE = 1.5 kg (3.3 lb.)

Unit casing

Camera unit

Dome cover

Side holes with

LED indicators

Control button

Camera AXIS P3364-L

Audio in

Audio out

SD memory card slot

Serial no.

Heater

Spring

routed along the wall

for cablesgaskets

I/O connector

Mounting bracket

Caution! The heater in the camera unit may be hot.

Network connector

(PoE)

Holes for cables

routed through the wall

AXIS P33-VE Network Cameras Installation Guide Page 7

ENGLISH

Install the hardware

Prepare the network cable

If a cable other than the provided cable is

used, you need to prepare a network cable

with a gasket. Gently force the cable through

the gasket provided and attach a network

connector. It may be necessary to pierce a

hole in the gasket with the resitorx screwdriver.

Notes:

• Do not force the network connector into the gasket.

• Do not pierce the gasket with a knife or other sharp object.

Prepare the unit casing (routing cables along the wall)

If the cables are to be routed along the wall, prepare the unit casing as follows:

Note: The cable shield is an optional accessory, not supplied with the product.

1. Loosen the two screws on the cable shield (not supplied) and detach the bottom part.

2. Attach the bottom part of the cable shield to the unit casing with the screw.

Replace clear/smoked dome cover (optional)

AXIS P3363-VE/AXIS P3364-VE is supplied with an optional dome. To replace the dome cover:

1. Loosen the 4 screws under the dome cover that hold the dome in place.

2. Transfer the gasket from the old dome to the new.

3. Replace the old dome with the new and tighten the screws.

Top part

Bottom part

Cable shield Unit casing

(optional accessory)

Page 8 AXIS P33-VE Network Cameras Installation Guide

Route the cables

Depending on whether you want to route the cables through or along the wall, follow the relevant

instructions below.

Routing cables through the wall

1. Using the drill template drill 4

holes in the wall.

2. Route the network cable (and the

I/O, audio cable if necessary)

through the wall and through the

holes in the mounting bracket.

3. Attach the mounting bracket to

the wall using 4 screws

appropriate for the wall material.

4. Remove the camera unit from the unit casing by pushing the springs aside.

5. Remove the gaskets from the back holes in the unit casing. If there is only one cable, remove

only one gasket.

6. Route the cables through these holes.

7. Drag the gaskets along the cables and plug them into the holes. The gaskets should fit snugly

with no folds or bends.

8. Attach the unit casing to the mounting bracket by tightening the four screws.

Routing cables along the wall

1. Using the drill template drill 4 holes in the wall.

2. Attach the mounting bracket to the wall using 4 screws appropriate for the wall material.

3. Remove the camera unit from the unit casing by pushing the springs aside.

4. Remove the gaskets from the side holes in the unit casing. If there is only one cable, remove

only one gasket.

5. Place the unit casing on the mounting bracket and attach it by tightening the four screws.

6. Pull the cables up through the side holes in the unit casing.

7. Drag the gaskets along the cable and plug them into the holes. The gaskets should fit snugly in

the holes with no folds or bends.

8. Re-attach the top part of the cable shield by tightening the two screws.

Note: The AXIS P3363-VE/P3364-VE/P3364-LVE can also be fitted with a metal conduit for protecting

the cabling when cables are routed along the wall.

Mounting bracket

Network cable with gasket

Unit casing

Remove gaskets

from holes

AXIS P33-VE Network Cameras Installation Guide Page 9

ENGLISH

Install the camera unit

1. Attach the network cable to the camera unit; and the cable for audio and I/O if required.

Note: Be careful not to stretch or bend the network cable too much since this could cause damage to

the network cable.

2. Insert the SD memory card (optional).

3. Pull aside the springs in the unit casing and click the camera unit in place.

4. Attach the fan connector to the connector in the camera unit.

5. Attach the two M4x8 20 screws to the camera for greater stability.

These screws are only necessary to secure against heavy shocks and vibrations.

Note: The AXIS P3363-VE/P3364-VE/P3364-LVE can also be fit-

ted with a metal conduit for protecting the cabling when

cables are routed along the wall.

Connector for fan

Camera unit

Network cable

Attach

screw to camera

Conduit

Page 10 AXIS P33-VE Network Cameras Installation Guide

Access the video stream

Use the tools provided on the Installation and Management Software CD to assign an IP address,

set the password and access the video stream. This information is also available from the support

pages on www.axis.com/techsup

Adjust the Lens

Open the Live View page in the web interface and make the following adjustments to the camera:

1. Loosen the locking screw.

2. Turn the lens holder to the desired position.

3. Turn the lens to make sure the (horizontal) lines on either side of the lens are aligned

horizontally.

Note: Ensure that the mark on the lens cover, between the horizontal lines, is facing up.

4. Once satisfied, gently tighten the locking screw and to secure the camera’s position.

5. Open the Focus Adjustment page in the Web interface under Setup > Basic Setup > Focus &

Zoom, and follow the on-screen instructions. Use the image window to adjust the focus and

zoom. See the online help files for more information.

Notes:

• Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been placed.

To correct this go to the Focus Adjustment page in the Web interface under Setup > Basic Setup > Focus

& Zoom, and adjust the focus again.

• When the zoom and focus are adjusted, the IR illumination is automatically aligned to the defined angle of

view.

Caution!

Adjusting the focus and zoom manually can damage the lens.

Locking screw

Horizontal line

Mark

Lens holder

Optical shield

AXIS P33-VE Network Cameras Installation Guide Page 11

ENGLISH

Complete the installation

1. Rotate the black protective shield inside the dome cover so it is aligned

with the camera’s position (not applicable to AXIS P3364-LVE).

2. If required, attach the weather shield to the camera before you attach

the dome cover (not applicable to AXIS P3364-LVE). To do this remove

the two screws in the dome cover. Transfer the washers from these

screws to the two long screws provided. Attach the weather shield

using the two long screws.

3. Attach the dome cover to the unit casing by tightening the 4 screws.

Note: AXIS P3364-LVE Network Camera: Before attaching the dome cover make sure the optical shield

sits well in place. See image on page 10.

For the AXIS P3364-LVE Network Camera, when the lens holder is tilted at a certain angle the

dome cover may block part of the IR illumination. In that case:

• loosen the locking screw

• rotate the lens holder 180°

• tighten the locking screw

• for correct image orientation, rotate the lens by 180°; make sure the horizontal lines are aligned and the

mark between them is facing up.

Black protective shield

Page 12 AXIS P33-VE Network Cameras Installation Guide

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet.

The product shall be connected using a shielded network cable (STP). All cables connecting the

product to the network switch shall be shielded (STP) and intended for their specific use. Make

sure that the network switch is properly grounded. See Electromagnetic Compatibility (EMC) on

page 2 for regulatory requirements.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from

a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an

active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo

connector must be used for the audio out.

SDHC memory card slot - The SD memory card can be used for local recording with removable

storage.

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications. In addition to

an auxiliary power and a GND pin, it provides the interface to:

• 1 transistor output - For connecting external devices such as

relays and LEDs. Connected devices can be activated by the

VAPIX® Application Programming Interface (API), by the output buttons on the Live

View page or by an Action Rule. The output will show as active (shown under System

Options > Ports & Devices) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between an

open and closed circuit, for example: PIRs, door/window contacts, and glass break

detectors. When a signal is received the state changes and the input becomes active

(shown under System Options > Ports & Devices).

Function Pin Notes Specifications

GND 1 Ground

3.3V DC

Power

2 Can be used to power auxiliary equipment.

Note: This pin can only be used as power out.

Max. load = 50mA

Digital

Input

3 Connect to GND to activate, or leave floating (or

unconnected) to deactivate.

Min. input= 0 to - 40V DC

Max. input=0 to + 40V DC

Digital

Output

4 Uses an open-drain NFET transistor with the source

connected to GND. If used with an external relay, a

diode must be connected in parallel with the load,

for protection against voltage transients.

Max. load = 100mA

Max voltage = + 40V DC

Pin1

Pin2

Pin3

Pin4

AXIS P33-VE Network Cameras Installation Guide Page 13

ENGLISH

The following connection diagram gives an example of how to connect an auxiliary device to the

AXIS P3363-VE/P3364-VE/P3364-LVE.

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Amber Steady during startup; flashes once during reset to factory default or while

restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

1

2

E.g. push button

3

4

3.3V

max. 50mA

D

S

G

Page 14 AXIS P33-VE Network Cameras Installation Guide

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the factory default settings:

1. Disconnect power from the camera.

2. Press and hold the Control button and reconnect power (see “Hardware overview” on page 6).

3. Keep the Control button pressed for about 15 seconds until the Status indicator displays amber.

4. Release the Control button. The process is complete after about 1 minute (when the Status

indicator turns green). The network camera has been reset to the factory default settings. The

default IP address is 192.168.0.90

5. Re-assign the IP address.

6. Refocus the camera.

It is also possible to reset parameters to factory default via the web interface. Go to Setup > System

Options > Maintenance.

Further information

The user manual is available from the Axis Web site at www.axis.com. To learn more about Axis'

products and technologies, visit www.axis.com/academy, the global learning center for network

video.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your Axis product.

To see the currently installed firmware version, see Setup > About in your web interface.

Warranty

For information about Axis' product warranty and thereto related information, please see

www.axis.com/warranty

FRANÇAIS

Mesures de sécurité

Lisez attentivement le présent Guide d'installation avant d'installer le produit Axis. Conservez le

Guide d'installation pour une utilisation ultérieure.

• Conservez le produit Axis dans un environnement sec et aéré.

• Évitez d'exposer le produit Axis aux vibrations, aux chocs ou à une forte pression.

N'installez pas le produit sur un support instable, ou des surfaces ou des murs instables ou

vibrants, car cela pourrait l'endommager.

• N'utilisez que les outils applicables pour installer le produit Axis ; une force excessive

pourrait endommager le produit.

• Pour le nettoyage, n’utilisez ni produits chimiques, ni substances caustiques ou aérosols.

Utilisez un chiffon humide pour le nettoyage.

• N’utilisez que des accessoires conformes aux caractéristiques techniques du produit. Ceux-

ci peuvent être fournis par Axis ou par un fournisseur tiers.

• Utilisez uniquement des pièces de rechange fournies ou recommandées par Axis.

• Ne tentez pas de réparer le produit vous-même, contactez Axis ou votre revendeur Axis

pour toute réparation.

• Ce produit Axis doit être utilisé conformément aux lois et réglementations locales en

vigueur.

• Pour pouvoir être utilisé à l'extérieur, ce produit Axis doit être placé dans un boîtier

d'extérieur homologué.

• Le produit Axis doit être installé par un professionnel qualifié. Veuillez vous conformer aux

règlements nationaux et locaux relatifs à l'installation.

Transport

• Pour transporter le produit Axis et éviter de l'endommager, utilisez l'emballage d'origine ou

un emballage équivalent.

Remplacement des piles

Ce produit Axis nécessite une pile au lithium CR2032 de 3,0 V pour l'alimentation de son horloge en

temps réel interne. Dans des conditions normales d'utilisation, cette pile est censée durer au moins

5 ans. Si la pile est faible, le fonctionnement de l'horloge en temps réel peut être affecté et

entraîner sa réinitialisation à chaque mise sous tension. Un message enregistré apparaît lorsque la

pile doit être remplacée. Ne remplacez la pile qu'en cas de nécessité !

Si la pile doit être remplacée, veuillez contacter www.axis.com/techsup pour obtenir de l’aide.

• Jetez les piles usagées conformément aux consignes du fabricant.

• Le remplacement incorrect de la pile peut entraîner un risque d'explosion.

• Remplacez la pile par une pile identique ou équivalente uniquement, en respectant les

recommandations du fabricant.

Nettoyer la bulle du dôme

• Veillez à ne pas rayer ou endommager la bulle du dôme. Ne nettoyez pas la bulle du dôme si

elle semble propre à l'œil nu et ne frottez jamais sa surface. Un nettoyage excessif peut

l'endommager.

• Pour le nettoyage général de la bulle du dôme, il est recommandé d'utiliser un savon ou un

détergent neutre sans solvant, non abrasif, avec de l'eau et un chiffon doux. Rincez

abondamment avec de l’eau tiède et propre. Séchez à l'aide d'un chiffon doux pour éviter

les tâches d'eau.

• N'utilisez jamais de détergents forts, d'essence, de benzène ou d'acétone, etc. et évitez

toute exposition directe aux rayons du soleil ou à des températures élevées lors du

nettoyage.

• Les bulles pour les produits L sont livrées avec une surface anti-rayures et le nettoyage de

la bulle est recommandé, cependant veuillez respecter les précautions ci-dessus.

Guide d’installation des Caméra réseau AXIS P33-VE Page 17

FRANÇAIS

AXIS P3363-VE/P3364-VE/P3364-LVE

Guide d’installation de la caméra réseau

Procédez comme suit pour installer la caméra réseau.

1. « Contenu de l’emballage » à la page 17

2. « Présentation du matériel » à la page 18

3. « Installation du matériel » à la page 19

4. « Accéder au flux vidéo » à la page 22

5. « Réglage de l’objectif » à la page 22

6. « Fin de l’installation » à la page 23

Remarques :

• Avant de commencer, vérifiez le contenu de l’emballage et assurez-vous que l’alimentation ainsi que les

câbles, les outils et la documentation nécessaires sont disponibles. Voir Contenu de l’emballage ci-dessous.

• Cette caméra réseau est conçue pour fonctionner avec un connecteur réseau (PoE). Si vous n’en disposez

pas, utilisez l’injecteur PoE Axis à 1 port (non fourni).

Contenu de l’emballage

Élément Modèles/variantes/remarques

Caméra réseau

avec module chauffant

AXIS P3363-VE

AXIS P3364-VE

AXIS P3364-LVE

Support de fixation

Bulles de dôme Bulle transparente non fumée (non applicable pour l’AXIS P3364-LVE)

Bulle transparente fumée

Protection étanche Non applicable pour l’AXIS P3364-LVE

Étiquettes 2 étiquettes adhésives portant le numéro de série

Kit de montage Tournevis Resitorx, 2 vis longues, gabarit de perçage, câble réseau de

5 mètres avec joint, 1 joint, connecteur de bornier.

CD CD du logiciel d'installation et de gestion

Documentation imprimée Guide d’installation (le présent document)

Clé d’authentification AVHS

Accessoires en option Adaptateur filet avec câble blindé

Rendez-vous sur www.axis.com pour en savoir plus sur les accessoires

disponibles.

Page 18 Caméra réseau AXIS P33-VE Guide d’installation

Présentation du matériel

Dimensions (H x l)

AXIS P3363-VE, AXIS P3364-VE, AXIS P3364-LVE = 110 x 179 x 179 mm (4,33 x 7,05 x 7,05")

Poids

AXIS P3363-VE, AXIS P3364-VE = 1,5 kg

AXIS P3364-LVE = 1,5 kg

Boîtier de l’unité

Caméra

Couvercle du dôme

Trous latéraux avec

Voyants lumineux

Bouton de commande

Caméra AXIS P3363

Entrée audio

Sortie audio

Logement pour carte mémoire SD

Numéro de série

Élément chauffant

Ressort

acheminés le long du mur

pour les câblesjoints

Connecteur d’E/S

Support de fixation

Attention : l’élément thermique de la caméra peut être chaud.

Connecteur réseau

(PoE)

Trous pour les câbles

acheminés dans le mur

Guide d’installation des Caméra réseau AXIS P33-VE Page 19

FRANÇAIS

Installation du matériel

Préparation du câble réseau

Si vous utilisez un câble autre que celui fourni,

il est nécessaire de préparer un câble réseau

avec un joint. Faites passer délicatement le

câble à travers le joint fourni et complétez-le

par un connecteur réseau. Il peut être

nécessaire de percer un trou dans le joint à l’aide du tournevis Resitorx.

Remarques :

• Ne forcez pas l’entrée du connecteur réseau dans le joint.

• Ne percez pas le joint avec un couteau ou tout autre objet tranchant.

Préparation du boîtier de l’unité (acheminement des câbles le long du mur)

Si les câbles doivent être acheminés le long du mur, préparez le boîtier de l’unité de la manière

suivante :

Remarque : Le blindage de câble est facultatif, et n’est pas fourni avec le produit.

1. Dévissez les deux vis sur le blindage de câble (non fourni) et détachez la partie inférieure.

2. Fixez la partie inférieure du blindage de câble au boîtier de l’unité avec la vis.

Remplacement de la bulle de dôme fumée ou non fumée (facultatif)

Les caméras AXIS P3363-VE et AXIS P3364-VE sont livrées avec un dôme facultatif. Pour remplacer

la bulle du dôme :

1. Sous la bulle du dôme, dévissez les 4 vis qui maintiennent le dôme en place.

2. Transférez le joint de l’ancien dôme au nouveau dôme.

3. Remplacez l’ancien dôme par le nouveau et serrez les vis.

Partie supérieure

Partie inférieure

Blindage de câble Boîtier de l’unité

(facultatif)

Page 20 Caméra réseau AXIS P33-VE Guide d’installation

Acheminement des câbles

Selon que vous souhaitez faire passer les câbles le long du mur ou dans le mur, suivez les

instructions correspondantes ci-dessous.

Acheminement des câbles dans le mur

1. En vous servant du gabarit de

perçage, percez 4 trous dans le

mur.

2. Faites passer le câble réseau (ainsi

que le câble d’E/S audio si

nécessaire) dans le mur et dans les

trous du support de fixation.

3. Fixez le support de fixation au mur

en utilisant 4 vis appropriées.

4. Retirez la caméra du boîtier de l’unité en écartant les ressorts.

5. Retirez les joints des trous arrière du boîtier de l’unité. S’il n’y a qu’un seul câble, retirez un seul

joint.

6. Acheminez les câbles par ces trous.

7. Faites glisser les joints le long des câbles et fixez-les dans les trous. Les joints doivent être

parfaitement ajustés, sans plis ni courbures.

8. Fixez le boîtier de l’unité au support de fixation en serrant les quatre vis.

Acheminement des câbles le long du mur

1. En vous servant du gabarit de perçage, percez 4 trous dans le mur.

2. Fixez le support de fixation au mur en utilisant 4 vis appropriées.

3. Retirez la caméra du boîtier de l’unité en écartant les ressorts.

4. Retirez les joints des trous latéraux du boîtier de l’unité. S’il n’y a qu’un seul câble, retirez un

seul joint.

5. Posez le boîtier de l’unité sur le support de fixation et fixez-le en serrant les quatre vis.

6. Faites passer les câbles à travers les trous latéraux du boîtier de l’unité.

7. Faites glisser les joints le long du câble et fixez-les dans les trous. Les joints doivent être

parfaitement ajustés aux trous, sans plis ni courbures.

8. Fixez à nouveau la partie supérieure du blindage de câble en resserrant les deux vis.

Remarque : Les caméras AXIS P3363-VE/P3364-VE/P3364-LVE peuvent également être dotées d’un tube

métallique pour protéger le câblage lors de l’acheminement des câbles le long du mur.

Support de fixation

Câble réseau avec joint

Boîtier de l’unité

Retirez les joints

des trous

La pagina sta caricando ...

Axis P3363-VE Manuale utente

Questo manuale è adatto anche per

Axis P3363-VE Manuale utente

in altre lingue

Documenti correlati

Altri documenti