IKEA RDW45 Manuale utente

RENLIG

DW45

GB

DE

FR

IT

ENGLISH 4

DEUTSCH 23

FRANÇAIS 45

ITALIANO 70

Contents

Safety information 4

Product description 5

Control panel 6

Washing programmes 7

Use of the appliance 8

Setting the water softener 9

Use of dishwasher salt 10

Use of rinse aid 11

Loading cutlery and dishes 11

Use of detergent 13

Setting and starting a washing programme

14

Care and cleaning 14

What to do if… 15

Technical data 17

Installation 18

Water connection 18

Electrical connection 19

Environment concerns 19

IKEA GUARANTEE 20

Subject to change without notice

Safety information

For your safety and correct operation of

the appliance, read this manual carefully

before installation and use. Always keep these

instructions with the appliance even if you

move or sell it. Users must fully know the oper-

ation and safety features of the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean household

utensils that are applicable for dishwashers.

• Do not put solvents in the appliance. Risk of

explosion.

• Put the knives and all items with sharp points

in the cutlery basket with their points down.

If not, put in a horizontal position in the up-

per basket.

• Use only branded products for dishwashers

(detergent, salt, rinse aid).

• If you open the door while the appliance is

in operation, hot steam can escape. Risk of

skin burns.

• Do not remove dishes from the dishwasher

before the end of the washing programme.

• When the washing programme is comple-

ted, disconnect the mains plug from the

mains socket and close the water tap.

• Only an authorised service engineer can re-

pair this appliance. Use only original spare

parts.

• Do not do repairs yourself to prevent injury

and damage to the appliance. Always con-

tact your local After Sales Service.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or lack

of experience and knowledge must not use

the appliance. They must have supervision

or instruction for the operation of the appli-

ance by a person responsible for their safe-

ty.

• Obey the safety instructions from the man-

ufacturer of the dishwasher detergent to

prevent burns to eyes, mouth and throat.

• Do not drink the water from the dishwasher.

Detergent residues can stay in your appli-

ance.

• Always close the door when you do not use

the appliance to prevent injury and not to

stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Children

must get supervision to make sure that they

do not play with the appliance.

• Keep all the packaging away from children.

There is a risk of suffocation.

• Keep all detergents in a safe area. Do not

let children touch the detergents.

• Keep children away from the appliance

when the door is open.

ENGLISH 4

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not connect

a damaged appliance. If necessary, contact

the supplier.

• Remove all packaging before first use.

• A qualified and competent person must do

the electrical installation.

• A qualified and competent person must do

the plumbing installation.

• Do not change the specifications or modify

this product. Risk of injury and damage to

the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth area

are damaged, that you can get access to

the inner side of the appliance.

If you have any doubts, please contact your

After Sales Service. Refer to the list of the

After Sales Services at the end of user man-

ual.

• Do not drill into the sides of the appliance to

prevent damage to hydraulic and electrical

components.

Warning! Carefully obey the instructions

for electrical and water connections.

Product description

1

2

3

4

5

6

7

8

9

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

9 Upper spray arm

ENGLISH 5

Control panel

1 On/off button

2 Programme selection/cancel button (SELECT/CANCEL)

3 Indicator lights

4 Programme indicator lights

Indicator lights

The indicator light comes on when the washing

programme is completed. Auxiliary functions:

• Level of the water softener.

• Activation/deactivation the audible signals.

• An alarm if the appliance has a malfunction.

1)

The indicator light comes on when it is neces-

sary to fill the salt container. Refer to the chap-

ter 'Use of dishwasher salt'.

The salt indicator light can stay on for some

hours, but it does not have an unwanted effect

on the operation of the appliance.

1) The indicator light is off while a washing programme operates.

Programme selection/cancel button

Use the programme selection/cancel button

for these operations:

• To set the washing programme. Refer to the

chapter 'Setting and starting a washing pro-

gramme'.

• To set the water softener. Refer to the chap-

ter 'Setting the water softener'.

• To deactivate/activate the audible signals.

Refer to the section 'Audible signals'.

• To cancel a washing programme in pro-

gress. Refer to the chapter 'Setting and start-

ing a washing programme'.

Setting mode

The appliance is in setting mode when all the

programme indicator lights are off and the end

indicator light flashes.

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

ENGLISH 6

– To deactivate/activate the audible signals.

If a programme indicator light is on, cancel the

programme to go back to the setting mode.

Refer to the chapter "Setting and starting a

washing programme".

Programme indicator lights A and B

Apart the selection of the corresponding wash-

ing programme, these lights have an auxiliary

functions:

• The adjustment of the water softener level.

• Deactivation/activation of the audible sig-

nals.

Audible signals

You can hear an audible signal:

• At the end of the washing programme.

• When the appliance has a malfunction.

The activation of the audible signals is set at

the factory.

Do these steps to deactivate the audible sig-

nals:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press and hold the programme selection/

cancel button until programme indicator

light A flashes and programme indicator

light B comes on.

4. Press the programme selection/cancel

button again.

– Programme indicator light A comes on.

– Programme indicator light B starts to

flash.

5. Wait until programme indicator light A

goes off.

– Programme indicator light B continues to

flash.

– The end indicator light comes on.

The audible signals are activated.

6. Press the programme selection/cancel

button again.

– The end indicator light goes off.

The audible signals are deactivated.

7. Switch off the appliance to save the oper-

ation.

Do these steps to activate the audible signals:

1. Do the above procedure until the end in-

dicator light comes on.

Washing programmes

Programme

Degree of

soil

Type of

load

Programme description

Intensive

Heavy soil

Crockery,

cutlery,

pots and

pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Normal

soil

Crockery,

cutlery,

pots and

pans

Prewash

Main wash up to 65°C

2 intermediate rinses

Final rinse

Drying

Quick

1)

Normal or

light soil

Crockery

and cutlery

Main wash up to 60°C

Final rinse

ENGLISH 7

Programme

Degree of

soil

Type of

load

Programme description

Eco

2)

Normal

soil

Crockery

and cutlery

Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

Rinse & Hold

Any

Partial load

(to be com-

pleted later

in the day)

1 cold rinse (to prevent food scraps to

bond).

Detergent is not necessary with this pro-

gramme.

1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load breakfast

and dinner crockery and cutlery.

2) Test programme for test institutes. This is the economy washing programme. Please refer to separate leaflet supplied, for

test data. Available only in 3 languages (English, French, German) just for test institutes purpose.

Consumption values (for full washing cycle)

Programme Programme duration

(minutes)

Energy consumption

(kWh)

Water consumption

(litres)

65-75 1,5-1,7 18-20

100-110 1,4-1,5 18-20

30 0,8 8

1)

120-130 0,8-0,9 12-13

11 0,1 5

1) The duration of this washing programme is prefixed (longer) than the others due to a prolonged drying and washing

phases.

The pressure and temperature of the wa-

ter, the variations of power supply and

the quantity of dishes can change these values.

Use of the appliance

Refer to the following instructions for each step

of procedure:

1. Make a check if the water softener level is

correct for the water hardness in your area.

If necessary set the water softener.

2. Fill the salt container with dishwasher salt.

3. Fill the rinse aid dispenser with rinse aid.

4. Load cutlery and dishes into the dishwash-

er.

5. Set the correct washing programme for the

type of load and soil.

6. Fill the detergent dispenser with the correct

quantity of detergent.

7. Start the washing programme.

If you use detergent tablets, refer to the

chapter 'Use of detergent'.

ENGLISH 8

Setting the water softener

The water softener removes minerals and salts

from the water supply. Minerals and salts can

have bad effect on the operation of the appli-

ance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international unit

for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact your

local water authority.

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10

43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9

37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8

29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7

23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6

19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5

15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4

11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2

< 4 < 7 < 0,7 < 5

1

1)

1

1)

1) No use of salt required.

You must set the water softener manually

and electronically.

Manual adjustment

The appliance is set at the factory at position

2.

1 2

Set switch to position

1 or 2.

Electronic adjustment

The water softener is set at the factory at

level 5.

1. Switch on the appliance.

ENGLISH 9

2. Make sure that the appliance is in setting

mode.

3. Press and hold the programme selection/

cancel button.

4. Release the programme selection/cancel

button when programme indicator light A

starts to flash and programme indicator

light B comes on.

5. Wait until programme indicator light B

goes off.

– Programme indicator light A starts to

flash.

– The end indicator light starts to flash.

6. Press the programme selection/cancel

button one time.

– Programme indicator light A starts to

flash.

– The setting function of the water softener

is activated.

– The end indicator light flashes to show

the level of the water softener.

Example: 5 flashes, pause, 5 flashes,

pause, etc... = level 5.

7. Press the programme selection/cancel

button one time to increase the water soft-

ener level by one step.

8. Press the on/off button to save the opera-

tion.

Use of dishwasher salt

Caution! Only use dishwashers salt.

Types of salt that are not applicable for

dishwashers cause damage to the water

softener.

1

2

3

Fill the salt container

with 1 litre of water

(only the first opera-

tion).

4

Fill the salt container

with 1,5-1,7 kg of

salt. Use the salt fun-

nel supplied.

5

Make sure that there

is no grain of salt out-

er of the salt com-

partment.

6

It is normal that water overflows from the

salt container when you fill it with salt.

ENGLISH 10

Use of rinse aid

Caution! Only use branded rinse aid for

dishwashers.

Do these steps to fill the rinse aid dispenser:

1

2

3

-

M

A

X

1

2

3

4

+

-

4

5

-

M

A

X

1

2

3

4

+

-

A

Fill when the rinse aid

indicator ( A ) be-

comes clear.

Caution! Do not fill the rinse aid dis-

penser with other products (e.g. dish-

washer cleaning agent, liquid detergent).

This can cause damage to the appliance.

Adjusting the dosage of rinse aid

The rinse aid dial is

set at the factory at

position 3.

To increase or de-

crease the dosage

refer to 'What to do

if...'

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable for

dishwashers.

Do not use the appliance to clean objects that

can absorb water (sponges, household cloths,

etc.).

• Before you load cutlery and dishes, do these

steps:

– Remove all food remainings and debris.

– Make burnt, remaining food in pans soft.

• While you load cutlery and dishes, do these

steps:

– Load hollow items (e.g. cups, glasses and

pans) with the opening down.

– Make sure that water does not collect in

the container or in a deep base.

– Make sure that cutlery and dishes do not

lie inside one another.

ENGLISH 11

– Make sure that cutlery and dishes do not

cover other cutlery and dishes.

– Make sure that glasses do not touch other

glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick coat-

ings can keep water droplets. Plastic items

do not dry as well as porcelain and steel

items.

• Put light items in the upper basket. Make

sure that the items do not move.

Caution! Make sure that the spray arms

can move freely before you start a

washing programme.

Warning! Always close the door after

you load or unload the appliance. An

open door can be dangerous.

Arrange service

dishes and large lids

around the edge of

the lower basket.

Use the cutlery grid. If the dimensions of

the cutlery prevent use of the grid, remove

it.

Arrange the items to let water touch all sur-

faces (left). For longer items, fold the cup

racks up (right).

Adjustment of the height of the upper basket

If you put large plates in the lower basket, first

move the upper basket to a upper position.

Warning! Adjust the height before you

load the upper basket.

Maximum height of the dishes in :

• Upper basket.

– Upper position: 20 cm.

– Lower position: 24 cm.

•Lower basket.

– Upper position: 31 cm.

– Lower position: 27 cm.

A

Do these steps to move the upper basket to the

upper or lower position:

1. Move the front runner stops (A) out.

2. Pull the basket out.

3. Put the basket in the upper or lower posi-

tion.

4. Replace the front runner stops (A) in their

initial position.

Caution! If the basket is in the upper

position, do not put cups on the cup racks.

ENGLISH 12

Use of detergent

Only use detergents (powder, liquid or

tablet) that are applicable for dishwash-

ers.

Follow the data on the packaging:

• Dosage recommended by the manufactur-

er.

• Storage recommendations.

Do not use more than the correct quantity of

detergent to save an environment.

1

2

3

Fill the detergent dis-

penser with deter-

gent.

If the washing pro-

gramme has a pre-

wash phase, put a

small quantity of de-

tergent on the inner

part of the appliance

door.

4

5

Use of detergent tablets

Put the detergent tablet in the detergent dis-

penser.

Detergent tablets contain:

•detergent

•rinse aid

• other cleaning agents.

Do these steps to use detergent tablets:

1. Make sure that the detergent tablets are

applicable for your water hardness. Refer

to the instructions from the manufacturer.

2. Set the lowest levels of water hardness and

rinse aid dosage.

It is not necessary to fill the salt container

and the rinse aid dispenser.

Do these steps when the drying results are

not satisfactory:

1. Fill the rinse aid dispenser with rinse aid.

2. Set the rinse aid dosage to position 2.

Do these steps to use the detergent powder

again:

1. Fill the salt container and the rinse aid dis-

penser.

2. Set the water softener to the highest level.

3. Do a washing programme without dishes.

4. Adjust the water softener. Refer to the

chapter 'Setting the water softener'.

5. Adjust the rinse aid dosage.

Different brands of detergent dissolve in

different times. Some detergent tablets

do not have the best cleaning results during

short washing programmes. Use long washing

programmes when you use detergent tablets

to fully remove the detergent.

ENGLISH 13

Setting and starting a washing programme

Set the washing programme with the

door ajar. The washing programme only

starts after you close the door. Until then it is

possible to modify the settings.

Do these steps to set and start a washing pro-

gramme:

1. Switch on the appliance.

2. Make sure that the appliance is in setting

mode.

3. Press the programme selection/cancel

button again and again to set the washing

programme. Refer to the chapter 'Washing

programmes'.

– The programme indicator light comes

on.

4. Close the door.

– The washing programme starts auto-

matically.

When the washing programme operates,

you cannot change the programme. Can-

cel the washing programme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

Cancelling a washing programme

1. Press and hold the programme selection/

cancel button for approximately 3 seconds.

– The programme indicator light goes off.

– The end indicator light starts to flash.

2. Release the programme selection/cancel

button to cancel the washing programme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme.

Fill the detergent dispenser with detergent be-

fore you set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point of

interruption.

End of the washing programme

Switch off the appliance in these conditions:

• The appliance stops automatically.

• The audible signals for the end of the pro-

gramme operate.

1. Open the door.

– The end indicator light comes on.

– The programme indicator light stays on.

2. Press the on/off button.

3. For better drying results, keep the door

ajar for some minutes before you remove

the dishes.

Let the dishes cool down before you remove

them from the appliance. Hot dishes are easily

damaged.

Removing the load

• First remove items from the lower basket,

then from the upper basket.

• There can be water on the sides and door

of the appliance. Stainless steel becomes

cool more quickly than the dishes.

Care and cleaning

Warning! Switch the appliance off before

you clean the filters.

Cleaning the filters

Important! Do not use the appliance without

the filters. Make sure that the installation of the

filters is correct. Incorrect installation will cause

unsatisfactory washing results and damage to

the appliance.

ENGLISH 14

1 2

A

C

B

Fully clean the filters

A, B and C below run-

ning water.

3

1

2

To remove filters B

and C, turn the han-

dle approximately

1/4 anticlockwise.

4

A

Remove the flat filter

A from the bottom of

the appliance.

5

2

1

Put the filter system in

position. To lock the

filter system, turn the

handle clockwise un-

til it locks in position.

Important! Do not remove the spray arms.

If the holes in the spray arms become clogged,

remove remaining parts of soil with a cocktail

stick.

Long periods of non-operation

Do these steps when you do not use the ap-

pliance for a long period:

1. Disconnect the mains plug from the mains

socket.

2. Close the water tap.

3. Keep the door open to prevent unpleasant

smells.

4. Keep the inner side of the appliance clean

(filters especially).

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth. Only

use neutral detergents. Do not use abrasive

products, scouring pads or solvents (acetone,

trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C. The

manufacturer is not responsible for damage

because of frost.

If not possible, empty the appliance and close

the door. Disconnect the water inlet hose and

remove water from the water inlet hose.

What to do if…

The appliance does not start or stops during operation.

If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution

to the problem yourself, contact your dealer or the After Sales Service.

ENGLISH 15

Problem Possible cause Solution

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent audi-

ble signal.

• 1 flash of the end

indicator light.

Malfunction:

The dishwasher

does not fill with wa-

ter.

The water tap is blocked or furred

with limescale.

Clean the water tap.

The water tap is closed. Open the water tap.

The filter in the water inlet hose is

blocked.

Clean the filter.

The connection of the water inlet

hose is not correct. The hose can be

kinked or squashed.

Make sure that the connection is

correct.

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent audi-

ble signal.

• 2 flashes of the

end indicator

light.

Malfunction:

The dishwasher will

not drain.

There is a blockage in the sink spi-

got.

Clean the sink spigot.

The connection of the water drain

hose is not correct. The hose can be

kinked or squashed.

Make sure that the connection is

correct.

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent audi-

ble signal.

• 3 flashes of the

end indicator

light.

Malfunction:

The anti-flood de-

vice operates.

Close the water tap and Contact your local After Sales Service.

Malfunction:

The programme

does not start.

The appliance door is not closed. Close the door.

Mains plug is not connected in. Put in the mains.

The fuse has blown out in the

household fuse box.

Replace the fuse.

After the check, switch on the appliance. The programme continues from the point of interrup-

tion. If the malfunction shows again, contact your After Sales Service.

ENGLISH 16

When the cleaning results are not satisfactory:

Problem Possible cause Solution

The dishes are

not clean

The selected washing programme is

not applicable for the type of load

and soil.

Set different washing programme.

The baskets are loaded incorrectly so

that water cannot reach all surfaces.

Load the baskets correctly.

Spray arms do not turn freely because

of incorrect arrangement of the load.

Make sure that the cutlery and dishes

do not block the spray arms.

The filters are dirty or not correctly in-

stalled.

Make sure that the filters are clean

and installed correctly.

The quantity of detergent is too little

or missing.

Make sure that the quantity of deter-

gent in detergent dispenser is correct.

Limescales

particles on the

dishes

The salt container is empty. Fill the salt container with salt.

The water softener is adjusted on a

wrong level.

Set the water softener.

The salt container cap is not closed

correctly.

Make sure that the salt container is

closed correctly.

The dishes are

wet and dull

No rinse aid has been used. Set the rinse aid dosage.

The rinse aid dispenser is empty. Fill the rinse aid dispenser.

There are

streaks, milky

spots or a blu-

ish coating on

glasses and

dishes

Wrong dosage of rinse aid. Decrease the rinse aid dosage.

Dry water drop

signs on

glasses and

dishes

Wrong dosage of rinse aid. Increase rinse aid dosage.

The detergent can be the cause. Use different type of detergent.

Technical data

Dimensions Width (cm) 44,6

Height (cm) 81,8-89,8

Depth (cm) 55,0

Water supply pressure

1)

Minimum

Maximum

0,5 bar (0,05 MPa)

8 bar (0,8 MPa)

Capacity (place settings) 9

ENGLISH 17

Energy class A

Washing class A

Drying class A

Noise (dB(A)) 50

Average annual energy con-

sumption (kWh)

2)

176

Average annual water con-

sumption (litres)

2)

2860

1) If the pressure in your area is lower or higher, please contact your After Sales Service.

2) The data is based on the washing programme for test institutes assuming 220 cycles per a year.

Information on the electrical connection, voltage and overall power is given on the rating

plate on the inner edge of the dishwasher door.

Installation

Caution! Refer to the assembly

instructions, in order to proceed with the

installation.

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Place the appliance on the floor and install it

under a counter (kitchen worktop or sink).

If a repair is necessary, the appliance must be

easily accessible for the engineer.

Put the appliance adjacent to a water tap and

a drain.

For the venting of the dishwasher only water

fill, water drain and power supply cable open-

ings are necessary.

Water connection

This appliance has a special inlet hose for

water stop later defined as aqualock.

Water inlet hose

Connected the appliance to a hot (max. 60°)

or cold water supply.

If the hot water comes from alternative sources

of energy that are more environmentally

friendly (e.g. solar or photovoltaic panels and

aeolian), use a hot water supply to decrease

energy consumption.

Connect the inlet hose to a water tap with an

external thread of 3/4".

Caution! Do not use connection hoses

from an old appliance.

Caution! If you connect the appliance to

new pipes or pipes that are not used for

a long time, we recommend to run the water

for some minutes before you connect the inlet

hose.

Aqualock inlet hose

The inlet hose is a high pressure resistant. It can

hold pressure at maximum 6 MPa. From ex-

ternal the inlet hose has a sheathing against

eventual damages. If the inner hose breaks,

the water that is in the hose will became dark.

You can see it across the special transparent

sheathing. Turn off the water tap immediately

and contact the After Sales Service.

ENGLISH 18

A

B

The aqualock inlet

hose is installed with

a safety device to

prevent accidental

loosening. To discon-

nect the hose:

• Press the lever ( B ).

• Turn the retaining

ring ( A ) anticlock-

wise.

Turn the inlet hose to

the left or the right to

suit the installation.

Tight the locknut cor-

rectly to prevent wa-

ter leaks.

If you use a inlet

hose extension

the total reached

length must be no

longer than 4 metres.

Drain hose

A

If you connect the

water drain hose to a

water trap under the

sink, remove the

plastic membrane

(A). If you do not re-

move the membrane,

remaining food can

cause a blockage in

the drain hose spigot.

Caution! Make

sure that the

water couplings are

tight to prevent wa-

ter leakage.

Electrical connection

Warning! The manufacturer is not

responsible if you do not follow these

safety precautions.

This appliance needs to be earthed according

to safety precautions.

Make sure that the rated voltage and type of

power on the rating plate agree with the volt-

age and the power of the local power supply.

Always use a correctly installed shockproof

socket.

Do not use multi-way plugs, connectors and

extension cables. There is a risk of fire.

Do not replace the mains cable yourself. Con-

tact the After Sales Service.

Make sure that the mains plug is accessible

after installation.

Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

This appliance complies with the E.E.C. Direc-

tives.

Environment concerns

The symbol on the product or on its

packaging indicates that this product may not

be treated as household waste. Instead it

should be taken to the appropriate collection

point for the recycling of electrical and

electronic equipment. By ensuring this product

is disposed of correctly, you will help prevent

potential negative consequences for the

environment and human health, which could

otherwise be caused by inappropriate waste

handling of this product. For more detailed

information about recycling of this product,

please contact your local council, your

household waste disposal service or the shop

where you purchased the product.

ENGLISH 19

Packaging materials

The materials with the symbol

are recycla-

ble. Dispose the packaging in a suitable col-

lection containers to recycle it.

Before disposal of appliance

Warning! Do these steps to dispose the

appliance:

• Pull the mains plug out of the mains socket.

• Cut off the mains cable and discard it.

• Discard the door catch. This prevents the

children to close themselves inside the ap-

pliance. Risk of suffocation.

IKEA GUARANTEE

How long is the IKEA guarantee valid?

This guarantee is valid for five (5) years from

the original date of purchase of Your appli-

ance at IKEA, unless the appliance is named

LAGAN in which case two (2) years of guar-

antee apply. The original sales receipt is re-

quired as proof of purchase. If service work is

carried out under guarantee, this will not ex-

tend the guarantee period for the appliance,

Which appliances are not covered by the

IKEA five (5) years guarantee?

The range of appliances named LAGAN and

all appliances purchased in IKEA before 1st of

August 2007

Who will execute the service?

IKEA service provider will provide the service

through its own service operations or author-

ized service partner network.

What does this guarantee cover?

The guarantee covers faults of the appliance,

which have been caused by faulty construction

or material faults from the date of purchase

from IKEA. This guarantee applies to domestic

use only. The exceptions are specified under

the headline “What is not covered under this

guarantee?” Within the guarantee period, the

costs to remedy the fault e.g. repairs, parts, la-

bour and travel will be covered, provided that

the appliance is accessible for repair without

special expenditure. On these conditions the

EU guidelines (Nr. 99/44/EG) and the respec-

tive local regulations are applicable. Replaced

parts become the property of IKEA.

What will IKEA do to correct the problem?

IKEA appointed service provider will examine

the product and decide, at its sole discretion,

if it is covered under this guarantee. If consid-

ered covered, IKEA service provider or its au-

thorized service partner through its own serv-

ice operations, will then, at its sole discretion,

either repair the defective product or replace

it with the same or a comparable product.

What is not covered under this guarantee?

• Normal wear and tear.

• Deliberate or negligent damage, damage

caused by failure to observe operating in-

structions, incorrect installation or by con-

nection to the wrong voltage, damage

caused by chemical or electro-chemical re-

action, rust, corrosion or water damage in-

cluding but not limited to damage caused by

excessive lime in the water supply, damage

caused by abnormal environmental condi-

tions.

• Consumable parts including batteries and

lamps.

• Non-functional and decorative parts which

do not affect normal use of the appliance,

including any scratches and possible color

differences.

• Accidental damage caused by foreign ob-

jects or substances and cleaning or unblock-

ing of filters, drainage systems or soap

drawers.

• Damage to the following parts: ceramic

glass, accessories, crockery and cutlery bas-

kets, feed and drainage pipes, seals, lamps

and lamp covers, screens, knobs, casings

and parts of casings. Unless such damages

can be proved to have been caused by pro-

duction faults.

ENGLISH 20

La pagina si sta caricando...

IKEA RDW45 Manuale utente

IKEA RDW45 Manuale utente

in altre lingue