L'Or Barista LM8016/90 Manuale utente

6

5

2

1

3

13

9

11 10

8

12

7

4

15

14

16

English 7

Dansk 22

Deutsch 37

Español 53

Français 69

Italiano 85

Nederlands 101

Norsk 117

Português 132

Svenska 148

English

7

English

Machine overview

1 On/off button

2 Ristretto button

3 Espresso button

4 Lungo button

5 Water tank lid

6 Water tank

7 Mains cord with plug

8 Used capsule drawer

9 Waste water drawer

10 Lower drip tray

11 Drip tray

12 Cup platform

13 Coffee outlets

14 Coffee dispensing spout cap

15 Capsule compartment

16 Lever

Introduction

Welcome to the L'OR Barista world! The L'OR Barista coffee system is the

only capsule coffee system that allows you to brew two cups of coffee at the

same time thanks to a coffee dispensing spout with double outlet.

The new and exclusive L'OR Barista double-shot coffee capsules allow you

to brew two cups of coffee or a double shot of coffee.

The L'OR Barista coffee machine is also compatible with the L'OR Espresso

single-shot coffee capsules. Thanks to the Dual Capsule Recognition

technology, the machine automatically recognizes the capsule size and

adapts the volume accordingly. All you need to do is press the button for

the type of coffee you desire.

Capsule compatibility

The L'OR Barista coffee machine has been designed to work with L’OR

Espresso single-shot capsules and L’OR Barista double-shot capsules, as

well as with Nespresso* capsules and aluminum capsules from coffee

brands produced by Jacobs Douwe Egberts, such as Douwe Egberts,

JACOBS, Jacqmotte, Jacques Vabre, Grand Mère, L'OR, Marcilla, Moccona,

Saimaza and Senseo.

*brand of a third party not connected to JACOBS DOUWE EGBERTS and / or

PHILIPS

Preparing for use

Before first use, remove all packaging materials from the machine.

When you use the machine for the first time or if you have not used it for 1

day or longer, perform the following steps:

8

English

1 Remove the water tank from the machine.

2 Rinse and fill the water tank under the tap. Place the water tank back

onto the machine.

3 Place a bowl under the coffee dispensing spout. Do not insert a capsule

and make sure that the lever is closed.

25 sec

°C

4 Press the on/off button to switch on the machine.

-

The on/off button flashes slowly to indicate that the machine is

heating up.

5 When all buttons light up continuously, press the lungo button.

-

Water flows from the coffee dispensing spout.

Note: When the internal water circuit is empty, the machine produces a

humming sound. When the machine dispenses water, it produces a less

loud humming sound. This is normal.

6 The machine is ready when all buttons light up continuously.

7 Empty the drip tray and waste water drawer (see 'Cleaning the used

capsule drawer and waste water drawer').

The machine is now ready for use.

9

English

Brewing coffee

Beverages and capsules

Capsules

L’OR aluminum capsules are available online at www.lorespresso.com and in

shops. You can choose from a variety of coffee capsules for different types

of coffee.

Beverages

Thanks to the Dual Capsule Recognition technology, the machine

automatically recognizes the capsule size and adapts the volume of your

drink accordingly. All you need to do is press the button for the type of

coffee you desire.

25 ml

Ristretto

2x 25 ml

50 ml

Double ristretto / Double shot of ristretto

40 ml

Espresso

2x 40 ml

80 ml

Double espresso / Double shot of espresso

10

English

110 ml

Lungo

2x 110 ml

220 ml

Double lungo / Double shot of lungo

220 ml

Grand Café Filtre

Preparing coffee

1 Press the on/off button to switch on the machine. The on/off button

starts flashing to indicate that the machine is heating up.

2 For one coffee, place one cup under the coffee dispensing spout.

3 For two coffees, place two cups under the coffee dispensing spout.

11

English

4 For a large coffee or Grand Café Filtre, remove the cup platform and the

drip tray, place the cup platform on the lower drip tray and place a large

cup or mug on the cup platform under the coffee dispensing spout.

5 Lift the lever.

6 Insert a capsule.

-

For a single cup of coffee, insert a L'OR Espresso single-shot capsule.

-

For two cups of coffee or one large coffee, insert a L'OR Barista

double-shot capsule.

7 Close the lever by pushing it down.

Warning: Do not insert a finger into the brew chamber when

closing the lever.

12

English

8 When the on/off button stops flashing and all buttons light up

continuously, press the button for the type of coffee you desire.

Caution: Do not lift the lever until the brewing process has finished.

Brewing is finished when the lights stop flashing and no more coffee

comes out of the coffee dispensing spout.

Brewing Grand Café Filtre

1 Remove the seal completely from the capsule.

2 Lift the lever and insert the capsule.

3 Close the lever.

4 Remove the drip tray with the cup platform. Put the drip tray aside and

place the cup platform on the lower drip tray.

13

English

5 Place a large cup or mug on the cup platform under the coffee

dispensing spout.

6 Press the lungo button to start the brewing process.

Adjusting the coffee quantity

Each coffee button has been programmed to brew coffee at its ideal setting.

Nevertheless, you can adapt the coffee quantity to your wishes, within a

range that ensures the best coffee quality.

L'OR Espresso single-shot

capsule

min standard max

Ristretto 20 ml 25 ml 40 ml

Espresso 30 ml 40 ml 50 ml

Lungo 85 ml 110 ml 135 ml

L'OR Barista double-shot

capsule

min standard max

Ristretto 40 ml 50 ml 60 ml

Espresso 60 ml 80 ml 100 ml

Lungo/Grand Café Filtre 170 ml 220 ml 270 ml

The coffee quantities for L'OR Espresso single-shot and L'OR Barista

double-shot capsules are adjusted separately:

1 Press the on/off button to switch on the machine.

2 Fill the water tank.

3 Insert a capsule and close the lever.

-

If you want to adjust the quantity for L'OR single-shot espresso

capsules, insert a normal L'OR Espresso capsule.

-

If you want to adjust the quantity for a L'OR Barista double-shot

capsule, insert a L'OR Barista capsule.

14

English

4 Press and hold the button of the coffee whose quantity you want to

adjust for 3 seconds until the button flashes quickly. Then release the

button. The machine starts brewing coffee.

5 Press the same button again when the cup contains the desired quantity

of coffee.

Note: If you press the coffee button too early, the machine programs the

minimum quantity of coffee shown in the table above. If you do not press

the coffee button, the machine programs the maximum quantity of

coffee.

Resetting the coffee quantities

To reset the coffee quantities to their factory settings:

1 Press the on/off button to switch on the machine.

2 Wait until the machine has heated up and all buttons light up.

3 Press and hold the ristretto, espresso and lungo buttons simultaneously

until all buttons flash quickly to show that the machine has been reset to

factory settings.

Cleaning and maintenance

Cleaning the used capsule drawer and waste water drawer

Check the used capsule drawer and waste water drawer regularly.

Note: For optimal hygiene, pull up the lever after use to ensure the last used

capsule falls into used capsule drawer.

1 Pull the used capsule drawer and the waste water drawer out of the

machine.

2 Remove the drip tray from the lower drip tray and rinse the drip tray and

the cup tray under a warm tap. Do not clean these parts in the

dishwasher.

15

English

3 Remove the used capsule drawer by pulling it up and empty it.

Caution: Be careful when you remove the used capsule drawer.

Capsules are still hot immediately after brewing.

4 Rinse all parts under a warm tap. Dry all parts with a soft cloth. You can

also clean all these parts in the dishwasher.

5 Reinsert the used capsule drawer into the waste water drawer.

6 Insert the waste water drawer with the used capsule drawer into the

machine.

7 Place the drip tray back onto the lower drip tray. Place the cup platform

onto the drip tray.

Cleaning other parts of the machine

1 Clean the outside of the machine with a soft damp cloth.

Caution: Never use scouring pads, abrasive cleaning agents or

aggressive liquids such as petrol or acetone to clean the machine.

Warning: Do not insert a finger into the capsule compartment

to avoid injury. There is an invisible piercer inside.

2 Clean the front of the machine with a soft damp cloth and clean the two

parts of the coffee dispensing spout (the coffee outlets and the spout

cover) under a warm tap or in the dishwasher.

3 Clean the water tank by rinsing it under a warm tap. The water tank is not

dishwasher-proof.

Note: Rinse the water tank and fill it with fresh water every 24 hours.

Cleaning the coffee circuit

Clean the coffee circuit every week to ensure you get coffee with an

optimum quality and taste.

16

English

1 Place a cup under the coffee dispensing spout.

2 Lift the lever to ensure the last used capsule falls into the used capsule

drawer.

3 Do not insert a new capsule and close the lever.

4 Press the lungo button.

5 Empty the cup after the machine has finished dispensing water.

6 Open the lever and repeat steps 3 to 5 to ensure proper cleaning of the

coffee circuit.

The machine is now ready for use.

Descaling

When to descale

-

Descale the machine when the ristretto and lungo button flash quickly a

few times after brewing. The descaling procedure takes up to 40 minutes

and consists of a descaling cycle and a rinsing cycle. Do not interrupt the

descaling procedure.

Why to descale

Descaling is essential for the following reasons:

-

It prolongs the life of your L'OR Barista coffee machine

-

It ensures maximum cup volume

-

It ensures maximum coffee temperature

17

English

-

The machine produces less sound during brewing

-

It prevents malfunctioning

If the descaling procedure is not performed correctly, scale residue remains

behind in the machine. This causes scale to build up more quickly and may

cause permanent and irreparable damage to the machine.

Use the correct descaler

Only citric acid-based descalers are suitable for descaling the L'OR Barista

machine. This type of descaler descales the machine without damaging it.

We advise you to use the dedicated L'OR Barista liquid descaler (CA6530). It

is available in bottles that contain liquid descaler for two descaling

procedures. You need half a bottle for one descaling procedure and can

store the other half for the next descaling procedure.

Descaling procedure

Note: If something goes wrong during the descaling procedure, e.g. because

you accidentally interrupt the descaling cycle, you have to restart the

descaling procedure from step 1.

1 Press the on/off button to switch on the machine.

2 Pour half a bottle of L'OR Barista liquid descaler (CA6530) into the water

tank.

3 Fill up the water tank with fresh tap water.

4 Make sure that there is no capsule in the capsule compartment.

18

English

5 Close the lever.

1.5L

6 Place a bowl with a minimum capacity of 1.5 liters on the lower drip tray

under the coffee dispensing spout to collect the descaling solution.

7 Press the ristretto and lungo button briefly at the same time.

8 The ristretto button starts to flash quickly. Press the ristretto button to

activate the descaling cycle.The machine dispenses the entire descaling

solution at regular intervals. This takes up to 30 minutes.

-

When the lungo button starts to flash quickly again, the first phase of

the descaling cycle has finished.

9 Remove and empty the bowl. Place the bowl back onto the lower drip

tray under the coffee dispensing spout.

10 Remove the water tank and rinse it under the tap. Fill the water tank with

cold tap water and place it back onto the machine.

19

English

11 Press the lungo button to start the flushing cycle.

Note: The water tank will be emptied without interruption. The flushing

cycle lasts about 3 minutes.

12 When the flushing cycle has finished, the ristretto and lungo button flash

a few times.

Note: It is normal that some water remains behind in the water tank after

the descaling procedure.

The machine switches off. The descaling procedure is finished.

Meaning of light signals

-

The on/off button flashes slowly: the machine is heating up.

-

The on/off button flashes quickly: the water tank is empty, fill the water

tank with tap water.

-

All buttons light up continuously: the machine is ready for use.

-

The selected coffee button flashes slowly: the machine is preparing the

coffee recipe.

-

The selected coffee button flashes quickly:

-

Programming is activated.

-

The new coffee quantity is saved.

-

The ristretto and lungo button flash simultaneously after brewing coffee:

you need to descale the machine.

Troubleshooting

This chapter summarizes the most common problems you could encounter

with your machine. If you are unable to solve the problem with the

information below, visit www.lorbarista.com/support for a list of frequently

asked questions or contact the Consumer Care Center in your country.

Problem Possible cause Solution

The machine does not switch

on.

The machine is not connected to

the mains.

Put the plug in an earthed wall

socket.

The on/off button is flashing

slowly.

The machine is heating up. This is normal.

The brewing time is longer

than before.

The machine is clogging up with

scale.

Descale the machine (see

'Descaling procedure').

20

English

Problem Possible cause Solution

The temperature of freshly

brewed coffee gradually

decreases.

The machine is clogging up with

scale.

Descale the machine (see

'Descaling procedure').

The pump makes a lot of

noise.

There is not enough water in the

water tank.

Fill the water tank with fresh tap

water.

The water tank is not placed

correctly.

Place the water tank correctly

and push it downwards.

The machine suddenly stops

brewing coffee.

There is not enough water in the

water tank.

Fill the water tank with fresh tap

water. Press the button of the

selected type of coffee again to

continue brewing. When the cup

is full, press the same button

again to stop the brewing

process.

The on/off button flashes

quickly.

The water tank is empty. Fill the water tank with fresh tap

water. Press the button of the

selected type of coffee again to

continue brewing. When the cup

is full, press the same button

again to stop the brewing

process.

I cannot close the capsule

compartment lever

completely.

Check if you use the

recommended L'OR capsule. Other

capsules may cause problems

during use..

The used capsule drawer is full. Empty the used capsule drawer

and insert the capsule again.

The capsule is not inserted

correctly.

Insert the capsule again and

check if it is inserted correctly.

The capsule is stuck. Open and close the lever a few

times with moderate force to

remove the capsule.

The lever does not open

completely.

The used capsule drawer is full. Empty the used capsule drawer.

The machine does not

dispense coffee or only

dispenses drops of coffee.

You have not flushed the machine

before first use.

Flush the machine before first

use (see 'Preparing for use').

There is not enough water in the

water tank.

Fill the water tank with fresh tap

water.

Scale has built up inside the

machine (see 'Descaling').

Descale the machine (see

'Descaling').

21

English

Problem Possible cause Solution

Coffee grounds end up in the

cup of coffee.

A small amount of ground coffee

will always end up on the bottom

of the cup.

This is normal.

The coffee flow splits or is not

straight.

The coffee dispensing spout cap is

not placed correctly or it is missing.

Snap the coffee dispensing

spout onto the coffee outlets.

The ristretto and lungo button

lights are flashing after

brewing.

This means it is time to descale the

machine to prevent it from

clogging with scale.

Descale the machine (see

'Descaling').

Why do I find water in the

waste water drawer?

The used capsule drawer and

waste water drawer catch the

residual water released after

brewing coffee.

This is normal.

The coffee quantity is not

what I expected.

The coffee quantity has been

adjusted.

Readjust the coffee quantity (see

'Adjusting the coffee quantity') or

reset the coffee quantities (see

'Resetting the coffee quantities').

My coffee is less warm. When you brew the first cup of the

day or when it has been a while

since your previous cup of coffee,

the inside of the machine is still

cold when you brew coffee.

You can pre-heat the machine

and coffee cup by brewing a cup

of coffee first without placing a

coffee capsule.

If you use a cold, thick-walled cup,

the coffee will cool down

immediately.

Use thin-walled cups, as thin-

walled cups will absorb less heat

from the coffee than thick-

walled cups. Make sure the size

of the cup matches the coffee

quantity. Do not brew a small

quantity of coffee in a large cup.

The machine is clogged with scale. Descale the machine when the

ristretto and lungo button flash

quickly a few times after brewing

(see 'Descaling').

You used cold milk. If you drink coffee with cold,

fresh milk, this will cool down

your coffee. You can prevent this

by preheating the milk.

The machine suddenly

switches off after some time.

This is the automatic shut-off

function.

The automatic shut-off function

is programmed to switch off the

machine after 9 minutes of

inactivity to save energy.

Dansk

22

Dansk

Oversigt over maskinen

1 On/off-knap

2 Ristretto-knap

3 Espressoknap

4 Lungo-knap

5 Vandtankens låg

6 Vandtank

7 Netledning med stik

8 Skuffe til brugte kapsler

9 Spildevandskuffe

10 Nederste drypbakke

11 Drypbakke

12 Kop-platform

13 Kaffeudløb

14 Hætte til kaffeudløbsrør

15 Kapselrum

16 Udløser

Introduktion

Velkommen til L'OR Barista-verdenen! L'OR Barista-kaffesystemet er det

eneste kapselkaffesystem, der giver dig mulighed for at brygge to kopper

kaffe på samme tid takket være et dobbelt kaffeudløb.

De nye og eksklusive L'OR Barista-kaffekapsler til dobbelt shot giver dig

mulighed for at brygge to kopper kaffe eller et dobbelt shot kaffe.

L'OR Barista-kaffemaskinen er også kompatibel med L'OR Espresso-

kaffekapsler til et enkelt shot. Takket være Dual Capsule Recognition-

teknologien genkender maskinen automatisk kapselstørrelsen og tilpasser

volumen herefter. Du skal blot trykke på knappen for den type kaffe, du

ønsker.

Kompatibilitet med kapsler

L'OR Barista kaffemaskinen er designet til at fungere med L'OR Espresso-

kapsler til enkelt shot og L'OR Barista-kapsler til dobbelt shot, samt med

Nespresso*-kapsler og aluminiumkapsler fra kaffemærker produceret af

Jacobs Douwe Egberts, såsom Douwe Egberts, JACOBS, Jacqmotte,

Jacques Vabre, Grand Mère, L'OR, Marcilla, Moccona, Saimaza og Senseo.

*mærke fra en tredjepart, der ikke er tilknyttet JACOBS DOUWE EGBERTS

og/eller PHILIPS

Klargøring

Fjern alle emballagematerialer fra maskinen, før den tages i brug.

Når du bruger maskinen første gang, eller hvis du ikke har brugt den i 1 dag

eller længere, skal du udføre følgende trin:

23

Dansk

1 Tag vandtanken ud af maskinen.

2 Skyl og fyld vandtanken under rindende vand. Sæt vandtanken tilbage på

plads i maskinen.

3 Sæt en skål under kaffeudløbsrøret. Sæt ikke en kapsel i, og sørg for, at

håndtaget er lukket.

25 sec

°C

4 Tænd maskinen ved at trykke på on/off-knappen.

-

On/off-knappen blinker langsomt for at angive, at maskinen varmer

op.

5 Når alle knapper lyser konstant, skal du trykke på lungo-knappen.

-

Der løber vand fra kaffeudløbet.

Bemærk: Når det indre vandkredsløb er tomt, siger maskinen en

summende lyd. Når maskinen dispenserer vand, siger den en mindre høj

summende lyd. Dette er normalt.

6 Maskinen er klar, når alle knapper lyser konstant.

7 Tøm drypbakken og spildevandsskuffen (se 'Rengøring af den brugte

kapselskuffe og spildevandsskuffe').

Maskinen er nu klar til brug.

La pagina sta caricando ...

L'Or Barista LM8016/90 Manuale utente

L'Or Barista LM8016/90 Manuale utente

in altre lingue

Documenti correlati

Altri documenti