NEC MultiSync® 20WGX²Pro Manuale del proprietario

MultiSync 20WGX

2

User’s Manual

UÏivatelská pﬁíruãka

Bedienerhandbuch

δηγίες ρήσης

Manual del usuario

Manuel Utilisateur

Manuale utente

Gebruikershandleiding

Podr´cznik u˝ytkownika

Руководство пользователя

Kullan∂c∂ Klavuzu

00Cover_all.p65 19/2/07, 1:48 PM1

Canadian Department of Communications Compliance

Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

1. Use the attached specified cables with the MultiSync 20WGX

2

Pro (L205GJ) colour monitor so as not to interfere with

radio and television reception.

(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,

and meet the following condition.

Power supply cord Non shield type, 3-conductor

Length 2.0 m

Plug shape

U.S.A

(2) Please use the supplied shielded video signal cable and USB cable with ferrite cores. Use of other cables and

adapters may cause interference with radio and television reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional

suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:

“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government

Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address: 500 Park Blvd, Suite 1100

Itasca, Illinois 60143

Tel. No.: (630) 467-3000

Type of Product: Display Monitor

Equipment Classification: Class B Peripheral

Model: MultiSync 20WGX

2

Pro (L205GJ)

We hereby declare that the equipment specified above conforms

to the technical standards as specified in the FCC Rules.

00Cover_all.p65 19/2/07, 1:48 PM2

TCO’03

Congratulations!

The display you have just purchased carries the TCO’03 Displays

label. This means that your display is designed, manufactured and

tested according to some of the strictest quality and environmental

requirements in the world. This makes for a high performance

product, designed with the user in focus that also minimizes the

impact on our natural environment.

Some of the features of the TCO’03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to improve the working environment for

the user and to reduce sight and strain problems. Important parameters are luminance,

contrast, resolution, reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneficial both for the user and the environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the manufacturer must have a certified

environmental management system such as EMAS or ISO 14 001.

• Restrictions on:

- chlorinated and brominated flame retardants and polymers

- heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in co-

operation with scientists, experts, users as well as manufacturers all over the world. Since the

end of the 1980s TCO has been involved in influencing the development of IT equipment in a

more user-friendly direction. Our labelling system started with displays in 1992 and is now

requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

00Cover_all.p65 19/2/07, 1:48 PM3

TCO’06

Congratulations!

The product you have just purchased carries the TCO’06 Media

Displays label. This means that your display is designed and

manufactured according to some of the strictest performance and

environmental criteria in the world. The manufacturer of this

display has selected it to be certified to TCO’06 Media Displays as

a sign of usability, high performance and reduced impact on the

natural environment.

Products certified to TCO´06 Media Displays are specifically designed for high quality

reproduction of moving images. Features such as luminance, colour rendition and response

time are important when watching TV or working with media, graphics, web design and other

applications that demand outstanding moving images.*

Other features of TCO’06 Media Displays:

Ergonomics

• Good visual ergonomics and image quality in order to reduce vision and strain problems.

Criteria for luminance, contrast, resolution, reflectance, colour rendition and response time.

Energy

• Energy saving mode – beneficial both for the user and the environment

• Electrical safety

Emissions

• Low electromagnetic fields surrounding the display

Ecology

• Product is designed for recycling. Manufacturer must have a certified environmental

management system such as EMAS or ISO 14 001

• Restrictions on:

- Chlorinated and brominated flame retardants and polymers

- Hazardous heavy metals such as cadmium, mercury, hexavalent chromium and lead.

All TCO labelled products are verified and certified by TCO Development, an independent third

party labelling organization. For over 20 years, TCO Development has been at the forefront of

moving the design of IT equipment in a more user-friendly direction. Our criteria are developed

in collaboration with an international group of researchers, experts, users and manufacturers.

Since the program’s inception, TCO labelled products have grown in popularity and are now

requested by users and IT-manufacturers all over the world.

Full specifications and lists of certified products can be found on our homepage

www.tcodevelopment.com

* For a display used primarily for conventional work tasks such as word processing, we recommend a display certified to our

office display series TCO’03 Displays or later version.

00Cover_all.p65 19/2/07, 1:48 PM4

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s

top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-

friendly products, and always strive to help define and comply with the latest independent standards from agencies such as

ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of

material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely

disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures

and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.

All required information concerning the disposal of the product and country-specific information on recycling facilities can be

found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)

Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode Power consumption LED colour

Normal Operation Approx. 92W Blue

Energy Saving Mode Less than 2W Amber

Off Mode Less than 1W Unlit

Manufacturer’s Recycling and Energy Information

WEEE Mark (European Directive 2002/96/EC)

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic

products carrying the mark (left) must be disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your

NEC display products, please follow the guidance of your local authority, or ask the shop where you

purchased the product, or if applicable, follow any agreements made between yourself and NEC.

The mark on electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

Chinese RoHS-information relevant for Chinese market

00Cover_all.p65 19/2/07, 1:48 PM5

Index

Warning, Caution ............................... English-1

Declaration ......................................... English-1

Contents ............................................. English-2

Quick Start ......................................... English-3

Controls .............................................. English-7

Recommended use .......................... English-10

Varování, Upozornûní........................... âesky-1

Prohlá‰ení ............................................ âesky-1

Obsah .................................................. âesky-2

Rychl˘ start .......................................... âesky-3

Ovládací prvky ..................................... âesky-7

Provozní pokyny ................................. âesky-10

Warnung, Vorsicht ............................. Deutsch-1

Erklärung ........................................... Deutsch-1

Inhalt der Verpackung ....................... Deutsch-2

Kurzanleitung .................................... Deutsch-3

Bedienelemente ................................ Deutsch-7

Einsatzempfehlungen ..................... Deutsch-10

ΠΡΕΙ∆ΠΙΗΣΗ, ΠΡΣΗ ..... Ελληνικά-1

∆ήλωση ......................................... Ελληνικά-1

Περιεµενα ................................. Ελληνικά-2

Γρήγρη Εκκίνηση ....................... Ελληνικά-3

Πλήκτρα Ελέγυ ........................ Ελληνικά-7

Συνιστώµενη ρήση ................... Ελληνικά-10

Advertencia, Peligro .......................... Español-1

Declaración ....................................... Español-1

Contenido .......................................... Español-2

Inicio rápido ....................................... Español-3

Controles ........................................... Español-7

Uso recomendado ........................... Español-10

Avertissement, Attention .................. Français-1

Déclaration ....................................... Français-1

Contenu ........................................... Français-2

Mise en marche rapide .................... Français-3

Commandes ..................................... Français-7

Conseils d’utilisation ...................... Français-10

Avvertenza, Attenzione ...................... Italiano-1

Dichiarazione ..................................... Italiano-1

Indice ................................................. Italiano-2

Guida rapida ...................................... Italiano-3

Comandi ............................................. Italiano-7

Raccomandazioni per l’uso .............. Italiano-10

Waarschuwing, Let op!.................Nederlands-1

Kennisgeving ...............................Nederlands-1

Inhoud ..........................................Nederlands-2

Snel aan de slag ..........................Nederlands-3

Besturingselementen ...................Nederlands-7

Aanbevolen gebruik ...................Nederlands-10

Uwagi dotyczàce zasilania monitora .... Polski-1

Ostrze˝enie, Uwaga ............................. Polski-2

Deklaracja ............................................ Polski-2

ZawartoÊç opakowania ........................ Polski-3

Pod∏àczenie monitora .......................... Polski-4

Menu regulacyjne ................................. Polski-8

Zalecenia eksploatacyjne ................... Polski-11

Предупреждение, Внимание ......... Русский-1

Заявление ....................................... Русский-1

Содержимое ................................... Русский-2

Краткое руководство по

началу работы ................................ Русский-3

Органы управления........................ Русский-7

Рекомендации по эксплуатации .. Русский-10

D∂kkat, Uyari ....................................... Türkçe-1

Bildirim ................................................ Türkçe-1

∑çindekiler ............................................ Türkçe-2

H∂zl∂ Baµlama ...................................... Türkçe-3

Kontroller ............................................. Türkçe-7

Tavsiye edilen kullan∂m ..................... Türkçe-10

00Cover_all.p65 19/2/07, 1:48 PM6

English

âesky

Deutsch

Ελληνικά

Español

Français

Italiano

Nederlands

Polski

Русский

Türkçe

01b_XChapterOpener 19/2/07, 1:49 PM1

01b_XChapterOpener 19/2/07, 1:49 PM2

English

English-1

WARNING

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM

WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE

POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

Caution:

When operating the MultiSync 20WGX

2

Pro

with a 220-240V AC power source in Europe, use the power cord provided with

the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.

If a power cord is not supplied with this equipment please contact your supplier.

When operating the MultiSync 20WGX

2

Pro with a 220-240V AC power source in Australia, use the power cord provided with

the monitor. If a power cord is not supplied with this equipment please contact your supplier.

For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by and

complies with the safety standard of your particular country.

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS

THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

Declaration

Declaration of the Manufacturer

We hereby certify that the colour monitor

MultiSync 20WGX

2

Pro (L205GJ) is in

compliance with

Council Directive 73/23/EEC:

– EN 60950-1

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

and marked with

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ENERGY STAR is a

U.S. registered trademark.

OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.

ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway,

Spain, Sweden, U.K.

NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.

MultiSync is a registered trademark of NEC Display Solutions, Ltd. in the countries of U.K., Italy, Austria, Netherlands, Switzerland,

Sweden, Spain, Denmark, Germany, Norway and Finland.

All other brands and product names are trademarks or registered trademarks of their respective owners.

As an ENERGY STAR

®

Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STAR guidelines

for energy efficiency. The ENERGY STA R emblem does not represent EPA endorsement of any product or service.

01_English 19/2/07, 1:49 PM1

English-2

Contents

Your new NEC MultiSync LCD monitor box* should contain the following:

• MultiSync 20WGX

2

Pro monitor with tilt/swivel adjust stand

• Power Cord

•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)

•Video Signal Cable (DVI-D to DVI-D)

• USB Cable

• User’s Manual

• Cable Cover

• CD ROM (includes complete User’s Manual in PDF format).

To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.

Power Cord

User’s Manual 15-pin mini D-SUB male to

15-pin mini D-SUB male

CD-ROM

Cable Cover

USB Cable

DVI-D to DVI-D

*

Remember to save your original box and packing material to transport or ship the monitor.

NOTE: This monitor can be equipped

with optional loudspeakers:

“MultiSync Sound bar”. Please ask

your dealer or check our website

http://www.nec-display-solutions.com

01_English 19/2/07, 1:49 PM2

English

English-3

Quick Start

To attach the MultiSync LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your

system (Figure A.1). Tighten all screws.

For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your

system (Figure A.2). Tighten all screws.

For the MAC: Connect the Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to

the Macintosh cable adapter (Figure B.1). Tighten all screws.

NOTE: Some Macintosh systems do not require a Macintosh cable adapter.

3. Remove the connector cover (Figure C.1).

4. Place hands on each side of the monitor to tilt the LCD panel 30 degrees angles (Figure C.2).

5. Connect all cables to the appropriate connectors (Figure C.3). Using the USB cable, connect the B type connector to the

USB upstream port on the right side of the monitor and the A type connector to the downstream port on the computer

(Figure C.3a). If you can use the cord from the USB device, use one of the downstream ports on the side of the monitor.

Figure A.1 Figure B.1

Macintosh

Cable Adapter

(not included)

Figure A.2

DVI signal cable

Figure C.3

Figure C.1 Figure C.2

Power Cord

DC-OUT*

DVI Cable

USB

Input1 (DVI)

Input2 (D-Sub)

* NEC optional product attachment.

Do not use this connector unless specified.

Figure C.3a

A Type

B Type

A Type

B Type

01_English 19/2/07, 1:49 PM3

English-4

6. Place the connector cover onto the back cabinet (Figure C.4).

7. Place all cables into the hooks (Figure C.5).

8. Place hands on each side if the monitor to tilt the LCD panel back 5° (Figure C.6).

9. Place the cable cover onto the stand (Figure C.6). To remove the cable cover, push the notch at the bottom of the cover

up (towards the top of the monitor) in order to unhook the cover from the stand (Figure C.7).

10. Connect the power cord to the power outlet (Figure D.1).

NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.

11. The vacation switch on the back side of the monitor must be turned on (Figure D.1). Turn on the monitor with the front

power button and the computer.

NOTE: The vacation switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be turned on

using the front button. DO NOT switch on/off repeatedly.

12. No-Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.

For further adjustments, use the following OSM controls:

• Auto Adjust Contrast (Analog input only)

• Auto Adjust (Analog input only)

Refer to the Controls section of this User’s Manual for a full description of these OSM controls.

NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.

Figure C.6 Figure C.7

Figure C.4 Figure C.5

Figure D.1

OFF Position

ON Position

Vacation Switch

01_English 19/2/07, 1:49 PM4

English

English-5

Figure M.1

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Place hands on each side of the monitor to tilt the LCD panel 5 degrees angles.

Remove the cable cover (Figure M.1).

Remove the connector cover (Figure M.2).

2. Disconnect all cables.

3. Place monitor face down on a non-abrasive surface (Figure M.3).

4. Remove the 2 screws connecting the stand to the monitor (Figure M.3).

Tilt and Swivel

Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).

NOTE: Handle with care when tilting and swivelling the monitor screen.

Figure TS.1

Figure M.2

M

E

N

U/

E

X

I

T

S

E

L

E

C

T

/

1

–

2

R

E

S

E

T

/

D

V

M

O

D

E

Figure M.3

01_English 19/2/07, 1:49 PM5

English-6

Figure M.4 Figure M.5

5. Lift up the stand to unlatch the upper hooks and remove the stand (Figure M.4).

6. Remove the 2 screws on the top of the monitor (Figure M.5). The monitor is now ready for mounting in an alternate

manner.

7. Connect the cables and place the connector cover on the back of the monitor.

8. Reverse this process to re-attach stand.

NOTE: Use only VESA-compatible alternative mounting method.

Handle with care when removing stand.

Flexible Arm Installation

This LCD monitor is designed for use with a flexible arm. To mount the monitor to a flexible arm:

1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.

2. Use the 4 screws to attach the arm to the monitor (Figure F.1).

NOTE: The LCD monitor should only be used with an approved arm (e.g. GS mark). To meet the safety requirements, the

monitor must be mounted to an arm, which guaranties the necessary stability under consideration of the weight of

the monitor.

Thickness of Bracket (Arm)

2.0~3.2mm

4 Screws (M4)

(Max Depth: 8.5mm)

Weight of LCD assembly: 4.6kg (MAX)

100mm

Figure F.1

12mm

M4

4 x 12mm with lock washer

and flat washer

01_English 19/2/07, 1:49 PM6

English

English-7

Controls

OSM (On-Screen Manager) control buttons on the front of the monitor

function as follows:

To access OSM menu, press any of the control buttons (MENU/EXIT, Left, Right, Down, Up).

To change signal input, press the SELECT button.

To change DV MODE, press the RESET/DV MODE button.

NOTE: OSM must be closed in order to change signal input.

NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the

RESET function by pressing the MENU/EXIT button.

Brightness/Contrast Controls

BRIGHTNESS

Adjusts the overall image and background screen brightness.

CONTRAST

Adjusts the image brightness in relation to the background.

AUTO CONTRAST (Analog input only)

Adjusts the image displayed to optimal settings.

ADVANCED DV MODE

Activates the Advanced Dynamic Video Mode.

DV MODE

Dynamic Visual Mode allows you to select setting for Movie, Photo and etc.

Auto Adjust (Analog input only)

Automatically adjusts the Image Position, H. Size and Fine settings.

Menu

Open OSM main menu.

Exits the OSM controls.

Exits to the OSM main menu.

Button

MENU/EXIT

Left/Right

Down/Up

SELECT/

1<->2RESET

RESET/DV MODE

Moves the highlighted area left/right to select control menus.

Moves the bar left/right to increase or decrease the adjustment.

Direct adjust of brightness if HOT KEY is set to ON.

Enters the OSM menu if HOT KEY is set to OFF.

Moves the highlighted area down/up to select one of the controls.

Direct adjust of contrast if HOT KEY is set to ON.

Enters the OSM menu if HOT KEY is set to OFF.

Enter the OSM sub menu. Active the selected function.

Change the Input source.

Resets the highlighted control menu to the factory setting. Switches the DV Mode.

4-Direction-Key

Up

Down

RightLeft

01_English 19/2/07, 1:49 PM7

English-8

Image Controls (Analog input only)

LEFT / RIGHT

Controls Horizontal Image Position within the display area of the LCD.

DOWN / UP

Controls Vertical Image Position within the display area of the LCD.

H.SIZE

Adjusts the horizontal size by increasing or decreasing this setting.

FINE

Improves focus, clarity and image stability by increasing or decreasing this setting.

Colour Control System

Colour Control System: Six colour presets select the desired colour setting (sRGB and NATIVE colour presets are

standard and cannot be changed).

R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour

will appear on screen and the direction (increase or decrease) will be shown by the bars.

NATIVE: Original colour presented by the LCD panel that is unadjustable.

sRGB: sRGB mode dramatically improves the colour fidelity in the desktop environment by a single standard RGB

colour space. With this colour supported environment, the operator could easily and confidently communicate colour

without further colour management overhead in the most common situations.

NOTE: When MOVIE, GAMING, or PHOTO is selected as the DV MODE, NATIVE is selected automatically as the six

colour preset and cannot be changed.

Tools

SHARPNESS: Adjust the image to get distinct or as soft a picture as is preferred.

EXPANSION: Selects the zoom mode.

FULL: The image is expanded to 1680 x 1050, regardless of the resolution.

ASPECT: The image is expanded without changing the aspect ratio.

OFF: The image is not expanded.

NOTE: EXPANSION is available only resolution under 1280 x 1024.

OFF TIMER: Monitor will automatically power-down when the end user has selected a predetermined amount of

time.

LED BRIGHTNESS: You can adjust the Blue LED brightness.

HOT KEY: You can adjust the brightness and contrast directly. When this function is set to ON, you can adjust the

brightness with left or right control and contrast with up or down control while the OSM menu is off.

INPUT RESOLUTION (Analog Input Only): Selects of resolution’s priority of input signal to one pair of the following:

1360 x 768, 1680 x 1050 or 1280 x 768, 1400 x 1050.

1360 x 768, 1680 x 1050: Determines the resolution to 1360 x 768 and 1680 x 1050.

1280 x 768, 1400 x 1050: Determines the resolution to 1280 x 768 and 1400 x 1050.

DDC/CI: This function allows the DDC/CI function ON or OFF.

FACTORY PRESET: Selecting Factory Preset allows you to reset all OSM control settings back to the factory

settings. The RESET button will need to be held down for several seconds to take effect. Individual settings can be

reset by highlighting the control to be reset and pressing the RESET button.

Menu Tools

LANGUAGE: OSM control menus are available in eight languages.

OSM LEFT/RIGHT: You can choose where you would like the OSM control image to appear horizontally on your

screen.

OSM DOWN/UP: You can choose where you would like the OSM control image to appear vertically on your screen.

OSM Turn Off: The OSM control menu will stay on as long as it is in use. In the OSM Turn Off submenu, you can

select how long the monitor waits after the last touch of a button to shut off the OSM control menu.

OSM Lock Out: This control completely locks out access to all OSM control functions without Brightness and

Contrast. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the

OSM controls are locked out. To activate the OSM Lock Out function, press SELECT, then right control button and

hold down simultaneously. To deactivate the OSM Lock Out, press SELECT, then left control button and hold down

simultaneously while in the OSM menu.

RESOLUTION NOTIFIER: This optimal resolution is 1680 x 1050. If ON is selected, a message will appear on the

screen after 30 seconds, notifying you that the resolution is not at 1680 x 1050.

01_English 19/2/07, 1:49 PM8

English

English-9

Information

The Information menu indicates the current input, display resolution, horizontal and vertical frequency, and polarity

settings of the monitor. The model and serial numbers of your monitor are also indicated.

OSM Warning

OSM Warning menus disappear with Exit button.

NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is

turned on or when there is a change of input signal, the No Signal window will appear.

RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power is

turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the

Resolution Notifier window will open. This function can be disabled in the Menu Tools.

OUT OF RANGE: When input signal is non-supported timing or the video signal doesn’t have proper

timing, the Out of Range menu will appear.

01_English 19/2/07, 1:49 PM9

English-10

Recommended use

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE

THE FOLLOWING WHEN SETTING UP AND USING

THE MULTISYNC LCD COLOUR MONITOR:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose

you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful

or fatal or may cause electric shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to

the monitor.

• Do not place any objects onto the monitor and do not use the monitor outdoors.

• The inside of the fluorescent tube located within the LCD monitor contains mercury.

Please follow the bylaws or rules of your municipality to dispose of the tube properly.

• Do not bend power cord.

• Do not use monitor in high temperatured, humid, dusty, or oily areas.

• Do not cover vent on monitor.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following

conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• If glass is broken, handle with care.

• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.

• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated

openings or place the monitor near a radiator or other heat sources. Do not put anything on top of

monitor.

• The power cable connector is the primary means of detaching the system from the power supply. The

monitor should be installed close to a power outlet which is easily accessible.

• Handle with care when transporting. Save packaging for transporting.

• Image Persistence: Please be aware that LCD Technology may experience a phenomenon known as Image Persistence.

Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT

monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of

time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was

displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be

turned off for one hour to erase the image.

NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and

using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

CAUTION

01_English 19/2/07, 1:49 PM10

English

English-11

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN

REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

• For optimum performance, allow 20 minutes for warm-up.

• Adjust the monitor height so that the top of the screen is at or slightly below eye level.

Your eyes should look slightly downward when viewing the middle of the screen.

• Position your monitor no closer than 40 cm and no further away than 70 cm from your

eyes. The optimal distance is 50 cm.

• Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize glare

and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or reference material)

directly in front of you to minimize turning your head while you are typing.

•Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Use the preset Size and Position controls with standard signals.

• Use the preset Colour Setting.

• Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.

• Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue to insufficient

contrast.

Cleaning the LCD Panel

Recommended cleaning of the LCD:

•To remove dust and dirt from the surface of the LCD panel, wipe gently with a soft cloth.

• Do not rub the LCD panel with rough material.

• Do not press on the surface of the LCD panel.

To avoid scratches

• Do not touch LCD panel with hard objects.

• Use only a soft cloth for cleaning the surface of the LCD panel.

To avoid stains

• Clean fingerprints, water drips, chemical spills and etc. from the LCD panel immediately or discoloration and spot will

occur.

• If the LCD panel is rubbed with too much force, cracking may occur, which will lead to abnormalities in the display.

To avoid breakage or screen trouble

• Do not push hard on the LCD panel surface.

• Do not set heavy objects on the LCD panel surface.

• Do not leave the LCD panel under constant pressure.

Cleaning the Cabinet

• Unplug the power supply.

• Use a soft cloth.

• Dampen the cloth with a mild detergent mixed with water, wipe the cabinet and dry with a soft cloth.

NOTE: Many plastics are used on the cabinet surface. DO NOT clean with benzene, alkaline detergent, alcoholic system

detergent, glass cleaner, wax, polish cleaner, soap powder or insecticide. Do not touch the cabinet with rubber or

vinyl for a prolonged period. These types of fluids and fabrics can cause the paint to deteriorate, crack or peel.

01_English 19/2/07, 1:49 PM11

English-12

01_English 19/2/07, 1:49 PM12

La pagina sta caricando ...

NEC MultiSync® 20WGX²Pro Manuale del proprietario

NEC MultiSync® 20WGX²Pro Manuale del proprietario

in altre lingue

Documenti correlati