Beta 1927AN Istruzioni per l'uso

Categoria
Utensili elettrici
Tipo
Istruzioni per l'uso
Beta
1927AN
Manuale d'uso ed istruzioni
I
Operation manual and instructions
GB
Notice d'utilisation et instructions
F
Gebruikshandleiding
NL
Bedienungsanleitung
D
Manual de uso e instrucciones
E
Manual de uso e instruções
P
Bruksanvisning
S
Käyttöohjeet
SF
Brugsmanual
DK
Bruksveiledning
N
Használati kézikönyv és útmutató
H
Kullanım ve Talimat Kılavuzu
TR
Instrukcja obsługi i zalecenia
PL
Beta
1927AN


Beta
I
MANUALE D’USO ED ISTRUZIONI PER AVVITATORI ANGOLARI PNEUMATICI PRODOTTI DA:
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
ITALIA
Documentazione redatta originariamente in lingua ITALIANA.
Conservare accuratamente le istruzioni di sicurezza e consegnarle al personale utilizzatore.
DESTINAZIONE D’USO
L’avvitatore angolare pneumatico è destinato al seguente uso:
Assemblaggio di elementi di collegamento filettati
Avvitare e svitare con l’impiego di bussole a macchina
è possibile l’impiego dell’avvitatore angolare anche in luoghi aperti esposti ad acqua e aria
Non sono consentite le seguenti operazioni:
è vietato l’impiego di bussole a mano
è vietato l’impiego di giunti e prolunghe, in quanto ne limita la potenza dell’avvitatore e aumenta il rischio di rottura
è vietato l’uso in ambienti contenenti atmosfere potenzialmente esplosive
è vietato bloccare il pulsante di azionamento con nastro adesivo o fascette
SICUREZZA DELLA POSTAZIONE DI LAVORO
Prestare attenzione alle superfici che possono diventare scivolose a causa dell’uso della macchina ed al pericolo di inciampamento
nel tubo flessibile dell’aria.
Durante l’utilizzo dell’utensile pneumatico per lavori eseguiti in quota, adottare tutte le misure preventive atte ad eliminare o
minimizzare i rischi ad altri lavoratori, conseguenti a possibili cadute accidentali dell’attrezzatura, (per esempio segregazione
dell’area di lavoro, adeguata segnalazione, ecc ).
Non utilizzare l’utensile pneumatico in ambienti contenenti atmosfere potenzialmente esplosive, perché possono svilupparsi scintille
in grado di incendiare polveri o vapori.
Evitare il contatto con apparecchiature in tensione, in quanto l’utensile pneumatico non è isolato ed il contatto con elementi in
tensione possono causare una scossa elettrica.
Impedire che bambini o visitatori possano avvicinarsi alla postazione di lavoro mentre si sta operando con l’utensile pneumatico. La
presenza di altre persone provoca distrazione che può comportare la perdita del controllo sull’utensile pneumatico.
SICUREZZA DEGLI UTENSILI PNEUMATICI
Non puntare mai il flusso d’aria verso se stessi o verso altre persone. L’aria compressa può causare lesioni serie.
Controllare raccordi di collegamento e tubazioni di alimentazione. Tutti i gruppi, i giunti e i tubi flessibili devono essere installati
conformemente ai dati tecnici relativi a pressione e flusso d’aria. Una pressione troppo bassa pregiudica il funzionamento
dell’utensile pneumatico, una pressione alta può causare danni e/o lesioni.
Evitare di piegare o stringere tubi flessibili, evitare l’uso di solventi e spigoli taglienti. Proteggere i tubi da calore, olio e parti rotanti.
Sostituire immediatamente un tubo flessibile danneggiato. Una tubazione di alimentazione difettosa può provocare movimenti
incontrollati del tubo dell’aria compressa. Polveri oppure trucioli sollevati dall’aria possono provocare lesioni agli occhi. Accertarsi
che le fascette per tubi flessibili siano sempre bene fissate.
INDICAZIONE PER LA SICUREZZA DEL PERSONALE
Si raccomanda la massima attenzione avendo cura di concentrarsi sempre sulle proprie azioni. Non utilizzare l’utensile pneumatico
in caso di stanchezza o sotto l’effetto droghe, bevande alcoliche o medicinali.
Utilizzare sempre i seguenti dispositivi individuale di protezione:
Occhiali di protezione;
Scarpe di sicurezza;
Otoprotettori;
Guanti di protezione per agenti fisici.
Guanti antivibrazione, da utilizzare a seguito di specifica analisi del livello di esposizione giornaliera alle vibrazioni per sistema
mano-braccio.
Avere cura di mettersi in posizione sicura mantenendo l’equilibrio in ogni momento. Una posizione di lavoro sicura ed una adatta
postura del corpo permettono di poter controllare meglio l’utensile pneumatico in caso di situazioni inaspettate.
Non indossare vestiti larghi, ne portare bracciali e catenine. Tenere capelli, vestiti e guanti lontano da parti in movimento. Vestiti
larghi, gioielli o capelli lunghi possono impigliarsi nelle parti in movimento.
Non respirare direttamente l’aria di scarico, evitando che possa arrivare agli occhi. L’aria di scarico dell’utensile pneumatico può
contenere acqua, olio, particelle metalliche ed impurità, che possono provocare pericoli.
ATTENZIONE
IMPORTANTE LEGGERE COMPLETAMENTE IL PRESENTE MANUALE PRIMA DI UTILIZZARE
L’UTENSILE PNEUMATICO. IN CASO DI MANCATO RISPETTO DELLE NORME DI SICUREZZA E
DELLE ISTRUZIONI OPERATIVE, POSSONO VERIFICARSI SERI INFORTUNI.
UTILIZZO ACCURATO DI AVVITATORI ANGOLARI PNEUMATICI
Per bloccare e supportare il pezzo in lavorazione utilizzare dispositivi di serraggio oppure morse. Non tenere il pezzo in lavorazione
con una mano o bloccato con il corpo; così facendo non è più possibile operare in sicurezza.
Non sottoporre l’utensile pneumatico a sovraccarico. Effettuare i propri lavori utilizzando esclusivamente l’utensile pneumatico
esplicitamente previsto per il caso.
Verificare sempre l’integrità della macchina. Non utilizzare alcun utensile pneumatico il cui interruttore di avvio/arresto sia difettoso.
Un utensile pneumatico che non può più essere arrestato o avviato è pericoloso e deve essere riparato.
Effettuare le regolazioni dell’avvitatore pneumatico a macchina ferma. Interrompere sempre l’alimentazione dell’aria nel caso in cui
lo stesso non venga utilizzato. Questa misura preventiva impedisce l’avvio accidentale dell’utensile pneumatico.
Quando gli utensili pneumatici non vengono utilizzati, conservarli al di fuori del raggio di accesso dei bambini. Non permettere di
usare l’utensile pneumatico a persone che non abbiano letto le presenti istruzioni.
Effettuare accuratamente la verifica dell’utensile pneumatico, accertandosi che parti mobili dell’utensile funzionino perfettamente,
che non si inceppino e che non vi siano pezzi rotti o danneggiati al punto da pregiudicarne il funzionamento. Far riparare le parti
danneggiate prima dell’impiego dell’utensile pneumatico.
Utilizzare sempre bussole a macchina in buone condizioni.
L’utensile pneumatico non deve essere modificato. Le modifiche possono ridurre l’efficacia delle misure di sicurezza ed aumentare i
rischi per l’operatore.
Fare riparare l’utensile pneumatico solo ed esclusivamente da personale specializzato e solo impiegando pezzi di ricambio
originali.
INDICAZIONI DI SICUREZZA PER AVVITATORI ANGOLARI PNEUMATICI
Controllare se la targhetta di identificazione è leggibile, eventualmente procurarsi la targhetta per la sostituzione dal produttore.
Durante l’utilizzo dell’avvitatore, possibili accidentali rotture dei singoli accessori possono proiettare pezzi ad elevata velocità.
L’operatore ed il personale addetto alla manutenzione devono essere in grado di gestire fisicamente il peso e la potenza
dell’utensile pneumatico.
E’ importante essere preparati a movimenti inaspettati dell’avvitatore angolare pneumatico dovuti a bloccaggio o rottura
dell’utensile da lavoro. Tenere sempre ben saldo l’utensile pneumatico e portare il proprio corpo e le proprie braccia in una
posizione che permetta di compensare questi movimenti. Queste misure possono evitare lesioni.
Evitare il contatto con elementi in movimento dell’utensile, in quanto possono causare lesioni.
Assicurarsi che il senso di rotazione dell’avvitatore angolare pneumatico sia consono all’utilizzo.
Nel caso di un’interruzione dell’alimentazione dell’aria oppure di una pressione di esercizio ridotta, spegnere l’utensile. Controllare
la pressione d’esercizio e, a pressione d’esercizio ottimale, avviare di nuovo.
Utilizzando l’utensile pneumatico è possibile che l’operatore, svolgendo le attività concernenti al lavoro, provi sensazioni fastidiose
a mani, braccia, spalle e nell’area del collo. Assumere una posizione comoda evitando posizioni sfavorevoli o cambiare la postura
possono aiutare ad evitare fastidi ed affaticamento.
Attenzione nel caso di funzionamento prolungato dell’utensile pneumatico: parte dell’utensile stesso e la bussola possono diventare
caldi. Utilizzare guanti di protezione.
Durante l’utilizzo dell’utensile pneumatico sul pezzo da lavorare si generano rumori, a volte anche nocivi, per il personale esposto.
Un’adeguata indagine fonometrica è necessaria per stabilire l’esatta assegnazione dello specifico dispositivo di protezione
individuale dell’udito (otoprotettore) da utilizzare.
Se da specifica indagine eseguita risulta che l’esposizione giornaliera alle vibrazioni generata durante l’utilizzo dell’utensile
pneumatico supera il valore limite di azione prevista dalla normativa vigente nel rispettivo paese, si devono utilizzare specifici
guanti antivibrazione.
Qualora dovreste accorgervi che la pelle delle dita diventa intorpidita, oppure bianca, presenta formicolio o dolore, sospendere il
lavoro con l’utensile pneumatico, informare il datore di lavoro e consultare un medico.
Tenere l’utensile pneumatico con una presa non eccessivamente salda ma sicura, considerando le necessarie forze di reazione
della mano.
Non trasportatore mai l’utensile pneumatico tenendolo per il tubo flessibile.
DISPOSITIVI DI PROTEZIONE INDIVIDUALI PREVISTI DURANTE LUTILIZZO DELLUTENSILE PNEUMATICO
La mancata osservanza delle seguenti avvertenze può causare lesioni fisiche e/o patologie.
DATI TECNICI
ATTACCO BUSSOLA 1/2“
CAPACITÀ VITE/DADO (8.8) M14 - 21 mm
CAPACITÀ VITE/DADO (12.9) M12 - 19 mm
VELOCITÀ A VUOTO 4700 Giri/min
COPPIA MASSIMA 240 Nm
ATTACCO ARIA 1/4” GAS Conico
PRESSIONE MASSIMA 6.2 Bar
CONSUMO D’ARIA MASSIMO 190 l/min
PESO 2,1 Kg
LUNGHEZZA 355 mm
MASSE BATTENTI TIPO A SINGOLO MARTELLO
LIVELLO PRESSIONE SONORA 89.4 dB(A) (EN ISO 15744)
LIVELLO POTENZA ACUSTICA 100.4 dB(A) (EN ISO 15744)
LIVELLO VIBRAZIONI 8.63 m/s
2
(ISO 28927-2)
LEGENDA
a: attacco aria 1/4” GAS conico
b: pulsante avviamento avvitatore
c: leva inversione cricchetto
d: selettore coppia min. – max
e: lubrificazione olio
f: ingrassaggio
Collegamento alimentazione dell’aria
Per un utilizzo corretto dell’utensile pneumatico rispettare sempre la pressione massima di 6.2 bar, misurata all’ingresso dell’utensile.
Alimentare l’utensile pneumatico con aria pulita e priva di condensa (immagine 2). Una pressione troppo elevata o la presenza di
umidità nell’aria di alimentazione riducono la durata delle parti meccaniche e possono causare danni all’utensile.
Ulteriori dispositivi di protezione individuali da utilizzare in funzione dei valori riscontrati nell’indagine di igiene ambientale/analisi
rischi nell’eventualità che i valori superino i limiti previsti dalle vigenti normative.
INDOSSARE SEMPRE DISPOSITIVI OTOPROTETTORI QUANDO SI ADOPERA L’UTENSILE
PNEUMATICO
INDOSSARE SEMPRE GLI OCCHIALI PROTETTIVI QUANDO SI ADOPERA L’UTENSILE
PNEUMATICO O QUANDO SI ESEGUE L’ATTIVITÀ DI MANUTENZIONE
UTILIZZARE SEMPRE GUANTI DI PROTEZIONE PER AGENTI FISICI DURANTE L’UTILIZZO
DELL’UTENSILE PNEUMATICO
UTILIZZARE SEMPRE CALZATURE DI SICUREZZA
UTILIZZARE GUANTI ANTIVIBRAZIONE DURANTE L’UTILIZZO DELL'AVVITATORE ANGOLARE, A
SEGUITO DI SPECIFICA ANALISI DEL LIVELLO DI ESPOSIZIONE GIORNALIERA ALLE
VIBRAZIONI PER SISTEMA MANO-BRACCIO
UTILIZZO
Avviamento / Arresto
Per avviare l’utensile pneumatico premere il pulsante di avviamento (immagine 4), tenendolo premuto durante l’esecuzione del lavoro.
Al rilascio del pulsante l’utensile pneumatico si arresta rapidamente.
Controllare la posizione della leva di inversione prima di azionare l’utensile pneumatico in modo da conoscere il senso di rotazione.
Impostazione senso di rotazione
L’avvitatore angolare pneumatico prevede il senso di rotazione orario ed antiorario (immagine 3):
senso orario - visto dal lato dell’operatore
senso antiorario - visto dal lato dell’operatore
Selezionare il senso di rotazione tramite la leva di inversione, con le seguenti possibilità:
selezione • coppia minima avvitamento (circa 1/3 coppia max)
selezione •• coppia massima avvitamento (circa 2/3 coppia max)
selezione coppia massima svitamento (coppia max)
Inserire sull’attacco quadro maschio la bussola a macchina desiderata, assicurandosi del corretto inserimento.
Interrompere sempre l’alimentazione dell’aria prima di effettuare operazioni di inserimento utensili o regolazioni, questa misura
preventiva impedisce l’avvio accidentale dell’utensile pneumatico.
Lubrificazione/Ingrassaggio
E’ indispensabile collegare l’utensile pneumatico ad un gruppo filtro-lubrificatore di linea a micronebbia (si consiglia art. Beta 1919F1/4)
regolato a due gocce al minuto. In questo caso si avrà una resa elevata con una ridotta usura delle parti meccaniche.
Nel caso la linea fosse sprovvista di lubrificazione, è necessario immettere periodicamente direttamente nell’utensile pneumatico olio
ISO 32, attraverso il foro di alimentazione dell’aria (immagine 6).
E’ necessario inoltre effettuare periodicamente l’ingrassaggio del cricchetto dell’avvitatore, attraverso l’ugello ingrassatore, utilizzando
grasso EP2 (immagine 5).
MANUTENZIONE
Gli interventi di manutenzione e di riparazione devono essere eseguiti da personale specializzato. Per tali interventi potete rivolgervi al
centro riparazioni di Beta Utensili S.p.A.
SMALTIMENTO
L’utensile pneumatico, gli accessori e gli imballaggi devono essere inviati ad un centro di raccolta smaltimento rifiuti, secondo le leggi
vigenti del paese in cui vi trovate.
GARANZIA
Questo utensile è fabbricato e collaudato secondo le norme attualmente vigenti nella Comunità Europea ed è coperto da garanzia per
un periodo di 12 mesi per uso professionale o 24 mesi per uso non professionale.
Vengono riparati guasti dovuti a difetti di materiale o di produzione mediante ripristino o sostituzione dei pezzi difettosi a nostra
discrezione.
L’effettuazione di uno o più interventi nel periodo di garanzia non modifica la data di scadenza della stessa.
Non sono soggetti a garanzia difetti dovuti all’usura, all’uso errato od improprio e le rotture causate da colpi e/o cadute. La garanzia
decade quando vengono apportate modifiche, quando l’utensile pneumatico viene manomesso o quando viene inviato all’assistenza
smontato.
Sono espressamente esclusi danni causati a persone e/o cose di qualsiasi genere e/o natura, diretti e/o indiretti.
DICHIARAZIONE DI CONFORMITÀ
Dichiariamo sotto la nostra piena responsabilità che il prodotto descritto è conforme a tutte le disposizioni pertinenti della Direttiva
Macchine 2006/42/CE e relative modifiche, nonché alla seguente normativa:
EN ISO 11148-6
Il Fascicolo Tecnico è disponibile presso:
BETA UTENSILI S.P.A.
Via A. Volta 18 - 20845 Sovico (MB) - ITALIA
Nome e qualifica del Responsabile
MASSIMO CICERI
(Consigliere Delegato)
BETA UTENSILI S.P.A. Data 01/01/2015
Via A. Volta 18
20845 Sovico (MB)
ITALIA
Beta
GB
OPERATION MANUAL AND INSTRUCTIONS FOR AIR ANGLE IMPACT WRENCHES
MANUFACTURED BY:
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
ITALY
Original documentation drawn up in ITALIAN.
Store the safety instructions with care and hand them over to the users.
PURPOSE OF USE
The air angle impact wrench can be used for the following purposes:
assembling threaded connecting parts
screwing and unscrewing by means of impact sockets
the angle impact wrench can also be used in open places exposed to water and air
The air angle impact wrench must not be used for the following operations:
the angle impact wrench must not be used with any hand sockets
the angle impact wrench must not be used with any couplers or extensions, because these result in reduced power of the impact
wrench and increased risk of breakage
the angle impact wrench must not be used in environments containing potentially explosive atmospheres
the trigger must not be locked with adhesive tape or clamps
WORK AREA SAFETY
Beware of both surfaces that may become slippery due to the use of the machine and the danger of tripping over the air hose.
While using the pneumatic tool for jobs performed high from the ground, take all necessary precautions, to eliminate or minimize
risk to other workers, following the accidental falling of any tools (for example, isolation of the work area and proper signs).
Do not operate the pneumatic tool in environments containing potentially explosive atmospheres, because sparks may be
generated, which can ignite the dust or fumes.
Avoid contact with live equipment, because the pneumatic tool is not insulated, and contact with live parts can cause electric
shocks.
Keep children and bystanders away from your workplace while operating the pneumatic tool. Distractions from other people can
cause you to lose control over the pneumatic tool.
PNEUMATIC TOOL SAFETY
Do not point the air flow to yourself or other people. Compressed air can cause serious injury.
Check the connections and the air supply lines. All units, couplers and hoses should conform to the product specifications in terms
of pressure and air volume. Too low pressure impairs the function of the pneumatic tool; too high pressure can cause damage
and/or injury.
Do not bend or tighten any hoses; avoid using solvents and sharp edges. Keep the hoses away from heat, oil and rotating parts.
Immediately replace any damaged hose. A defective feed pipe may cause uncontrolled movements of the compressed air pipe.
Raised rust or chips may cause eye injury. Make sure that the hose clamps are always secured firmly.
PERSONNEL SAFETY
Stay alert; watch what you are doing. Do not use the pneumatic tool while tired or under the influence of drugs, alcohol, or
medication.
Always use the following personal protective equipment:
Eye protection;
Safety shoes;
Hearing protection;
Protective gloves against physical agents;
Anti-vibration gloves, to be worn following a specially conducted survey of the daily exposure of the hand-arm system to
vibration.
Make sure you are in a safe position, keeping proper balance at all times. A safe working position and a proper body posture
enable better control of the pneumatic tool in unexpected situations.
Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothing, jewellery, and
long hair can get caught in moving parts.
Do not directly inhale the exhaust air, and prevent it from getting into your eyes. The exhaust air of the pneumatic tool can contain
water, oil, metal particles and impurities, which may cause hazards.
CAUTION
IT IS IMPORTANT TO READ THIS MANUAL THOROUGHLY BEFORE USING THE PNEUMATIC
TOOL. FAILURE TO COMPLY WITH THE SAFETY STANDARDS AND OPERATING INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY.
AIR ANGLE IMPACT WRENCH USE AND CARE
Use clamping devices or a vice to secure and support the workpiece. Holding the workpiece by hand or against your body will not
allow for safe operation of the pneumatic tool.
Do not overload the pneumatic tool. Use the pneumatic tool intended for your work.
Always check that the machine is free from defects. Do not use a pneumatic tool that has a defective On/Off switch. A pneumatic
tool that can no longer be stopped or started is dangerous and must be repaired.
Make any adjustments while the air angle impact wrench is not working. Always disconnect the air supply when not in use. This
safety measure prevents accidental starting of the pneumatic tool.
Store idle pneumatic tools out of the reach of children. Do not allow persons unfamiliar with these instructions to operate the
pneumatic tool.
Maintain the pneumatic tool with care. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the operation of the pneumatic tool. Have damaged parts repaired before using the pneumatic tool.
Always use impact sockets in good condition.
Do not modify the pneumatic tool. This can reduce the effectiveness of safety measures and increase operator risk.
Have the pneumatic tool repaired only through a qualified repair person and only using original replacement parts.
AIR ANGLE IMPACT WRENCH SAFETY
Make sure that the nameplate is readable; get a replacement nameplate from the manufacturer, if need be.
While the impact wrench is being used, any accidental breakages of individual accessories may cause pieces to be thrown at high
speed.
Operators and maintenance personnel should be physically able to handle the weight and power of the pneumatic tool.
It is important to be prepared for unexpected movements of the air angle impact wrench resulting from a jammed or broken work
tool. Maintain a firm grip on the pneumatic tool and position your body and arms to allow you to resist such movements. These
precautions can prevent injuries.
Avoid contact with any moving parts of the tool, since these can cause injuries.
Make sure that the direction of rotation of the air angle impact wrench is fit for use.
Turn off the tool in case of air supply failure or low operating pressure. Check the operating pressure; turn on the tool again when
optimal operating pressure is resumed.
When using the pneumatic tool, the operator can experience discomfort in the hands, arms, shoulders, or neck area. Adopt a
comfortable posture, and avoid awkward or off-balanced postures, or change posture to help avoid discomfort and fatigue.
Caution: If the pneumatic tool is used over a protracted period of time, part of the tool and the socket may become hot. Wear
protective gloves.
Using the pneumatic tool on the workpiece generates noise, which may prove harmful to the exposed personnel. A proper
phonometric survey is required to determine the personal hearing protective equipment (hearing protection) to use.
If a specially conducted survey suggests that the daily exposure to vibration generated from the pneumatic tool exceeds the limit
value under the regulations in force in the respective country, anti-vibration gloves must be worn.
If you notice that the skin of your fingers becomes numb, turns white, tingles or hurts, stop working with the pneumatic tool, inform
your employer and seek medical advice.
Hold the pneumatic tool with a not too firm yet secure grip, compliant with the required hand reaction forces.
Never carry the pneumatic tool by the hose.
PERSONAL PROTECTIVE EQUIPMENT TO WEAR WHILE OPERATING PNEUMATIC TOOL
Failure to observe the following warnings may result in physical injury and/or disease.
PRODUCT SPECIFICATIONS
SOCKET DRIVE 1/2“
BOLT CAPACITY (8.8) M14 - 21 mm
BOLT CAPACITY (12.9) M12 - 19 mm
FREE SPEED 4700 rpm
MAXIMUM TORQUE 240 Nm
AIR INLET 1/4” GAS, cone-shaped
MAXIMUM PRESSURE 6.2 bars
MAXIMUM AIR CONSUMPTION 190 l/min
WEIGHT 2.1 kg
LENGTH 355 mm
HAMMER DEVICE TYPE SINGLE HAMMER
SOUND PRESSURE LEVEL 89.4 dB(A) (EN ISO 15744)
SOUND POWER LEVEL 100.4 dB(A) (EN ISO 15744)
VIBRATION LEVEL 8.63 m/s
2
(ISO 28927-2)
KEY TO SYMBOLS
a: air inlet 1/4” GAS, cone-shaped
b: impact wrench trigger
c: ratchet reverse lever
d: min. – max torque selector
e: oil lubrication
f: greasing
INSTRUCTIONS FOR INSTALLING DEVICES
Air supply connection
For optimal use of the pneumatic tool, always keep to a maximum pressure of 6.2 bars, as measured at the tool inlet. Feed the
pneumatic tool with clean, condensate-free air (picture 2). Excessively high pressure or humidity in supply air results in shorter life for
the mechanical parts and may damage the tool.
Additional personal protective equipment to wear according to the values found in the environmental hygiene/risk analysis survey if
the values exceed the limits under current regulations.
ALWAYS WEAR HEARING PROTECTION WHILE OPERATING PNEUMATIC TOOL
ALWAYS WEAR EYE PROTECTION WHILE OPERATING PNEUMATIC TOOL OR PERFORMING
MAINTENANCE JOBS
ALWAYS WEAR PROTECTIVE GLOVES AGAINST PHYSICAL AGENTS WHILE OPERATING
PNEUMATIC TOOL
ALWAYS WEAR SAFETY SHOES
WEAR ANTI-VIBRATION GLOVES WHILE OPERATING PNEUMATIC TOOL FOLLOWING A
SPECIALLY CONDUCTED SURVEY OF LEVEL OF DAILY EXPOSURE OF HAND-ARM SYSTEM TO
VIBRATION
USE
Start / Stop
To start the pneumatic tool, press the trigger (picture 4), and keep it pressed during the job to be performed. Releasing the trigger will
cause the pneumatic tool to stop quickly.
Check the position of the reverse lever before operating the pneumatic tool, so as to know the direction of rotation.
Direction of rotation setting
The air angle impact wrench can rotate both clockwise and anticlockwise (picture 3):
clockwise - seen from the operator's side
anticlockwise - seen from the operator's side
Use the reverse lever to select the direction of rotation; the following options are available:
selection • minimum screwing torque (approximately 1/3 of max. torque)
selection •• maximum screwing torque (approximately 2/3 of max. torque)
selection maximum unscrewing torque (max. torque)
Fit the required impact socket onto the male drive, and make sure that it is inserted correctly.
Always disconnect the air supply before fitting in tools or making adjustments; this precaution will prevent the pneumatic tool from being
accidentally started.
Lubrication/Greasing
The pneumatic tool must be connected to a filter-lubricator unit (we recommend Beta item 1919F1/4) provided with an air-oil microfog
mixer, set at two drops per minute. This will result in a high-performing tool and wear-resistant mechanical parts.
If lubrication is not provided to the line, oil ISO 32 must be periodically poured into the pneumatic tool, through the air supply hole
(picture 6).
Furthermore, the impact wrench ratchet must be periodically greased, through the grease nozzle, using grease EP2 (picture 5).
MAINTENANCE
Maintenance and repair jobs must be carried out by trained personnel. For such jobs, you can contact Beta Utensili S.P.A.'s repair
centre.
DISPOSAL
The pneumatic tool, accessories and packaging should be sent to a waste disposal centre, in accordance with the laws in force in your
country.
WARRANTY
This tool is manufactured and tested in accordance with current EU regulations, and is covered by a 12-month warranty for professional
use or a 24-month warranty for nonprofessional use.
We will repair any breakdowns caused by material or manufacturing defects by fixing the defective pieces or replacing them at our
discretion.
Should assistance be required once or several times during the warranty period, the expiry date of this warranty will remain unchanged.
This warranty will not cover defects due to wear, misuse or breakdowns caused by blows and/or falls. In addition, this warranty will no
longer be valid if any changes are made, or if the pneumatic tool is forced or sent to the customer service in pieces.
This warranty explicitly excludes any damage to people and/or things, whether direct or consequential.
DECLARATION OF CONFORMITY
We hereby declare, assuming full responsibility, that the described product complies with all the relevant provisions of Machine
Directive 2006/42/EC and amendments thereto, as well as with the following standard:
EN ISO 11148-6
The Technical Brochure is available at:
BETA UTENSILI S.P.A.
Via A. Volta 18 - 20845 Sovico (MB) - ITALY
Name and title of person in charge
MASSIMO CICERI
(Managing Director)
BETA UTENSILI S.P.A. Date 01/01/2015
Via A. Volta 18
20845 Sovico (MB)
ITALY
Beta
F
NOTICE D’UTILISATION ET INSTRUCTIONS POUR CLÉS À CHOCS À RENVOI D’ANGLE PRODUITES
PAR :
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
ITALIE
Documentation rédigée à l’origine en langue ITALIENNE.
Garder scrupuleusement les instructions sur lacurité et les remettre au personnel concerné.
DESTINATION D’UTILISATION
La clé à chocs à renvoi d’angle pneumatique est destinée à l’utilisation suivante :
Assemblage d’éléments de branchement filetés ;
Vissage et dévissage par le biais des douilles à chocs ;
Possibilité d’utilisation de la clé à chocs à renvoi d’angle en plein air ou dans des lieux exposés à l’eau.
Les opérations suivantes ne sont pas autorisées :
Il est interdit d’utiliser des douilles ;
Il est interdit d’utiliser des raccords et des rallonges car ils limitent la puissance de la clé à chocs à renvoi d’angle et augmentent
le risque de rupture ;
Il est interdit d’utiliser la clé à chocs dans des lieux contenant des atmosphères potentiellement explosives ;
Il est interdit de bloquer la touche d’actionnement avec du ruban adhésif ou des colliers.
SÉCURITÉ DU POSTE DE TRAVAIL
Faire attention aux surfaces qui peuvent devenir glissantes à cause de l’utilisation de la machine et au risque de trébucher dans le
tuyau flexible de l’air.
Lors de l’utilisation de l’outil pneumatique pour les travaux effectués en hauteur, adopter toutes les mesures de prévention pour
éliminer ou réduire au minimum les risques envers les autres travailleurs, dus notamment aux possibles chutes accidentelles de
l’outil (en délimitant par exemple la zone de travail et en prévoyant des signaux visibles etc.).
Ne pas utiliser l’outil pneumatique dans des lieux présentant des atmosphères potentiellement explosives car les étincelles peuvent
donner feu aux poussières ou aux vapeurs.
Éviter le contact avec des équipements sous tension car l’outil pneumatique n’est pas isolé et le contact avec des éléments sous
tension peut provoquer une secousse électrique.
Empêcher que des enfants ou des visiteurs s’approchent du poste de travail pendant les opérations avec l’outil pneumatique. La
présence d’autres personnes peut distraire l’opérateur qui peut perdre le contrôle de l’outil pneumatique.
MESURES DE SÉCURITÉ POUR LES OUTILS PNEUMATIQUES
Ne diriger en aucun cas le débit d’air vers soi ou en direction d’autres personnes. L’air comprimé peut provoquer de graves lésions.
Contrôler les branchements et les câbles d’alimentation. Tous les groupes, les raccords et les tuyaux flexibles doivent être installés
conformément aux données techniques relatives à la pression et au débit d’air. Une pression trop basse empêche le
fonctionnement de l’outil pneumatique, une forte pression peut provoquer des dommages et/ou des lésions.
Éviter de plier ou de serrer les tuyaux flexibles, éviter l’utilisation de solvants et de bords coupants. Protéger les tuyaux contre la
chaleur, l’huile et les pièces tournantes. Remplacer immédiatement les tuyaux flexibles endommagés. Un tuyau d’alimentation
défectueux peut provoquer des mouvements incontrôlés du tuyau d’air comprimé. Les poussières ou les copeaux soulevés par l’air
peuvent causer des lésions aux yeux. S’assurer que les colliers pour tuyaux flexibles soient toujours bien fixés.
RECOMMANDATIONS POUR LA SÉCURITÉ DU PERSONNEL
La plus grande attention doit être apportée aux actions effectuées. Ne pas utiliser l’outil pneumatique en cas de fatigue ou sous
l’effet de drogues, de boissons alcooliques ou de médicaments..
Utiliser systématiquement les équipements de protection individuelle suivants :
Lunettes de protection ;
Chaussures de sécurité ;
Dispositifs de protection de l’ouïe ;
Gants de protection contre les agents physiques;
Gants anti-vibration, à utiliser suite à une analyse spécifique en fonction du niveau d’exposition quotidienne aux vibrations du
système main-bras.
Se placer en position sûre en veillant à ne jamais perdre l’équilibre. Une position de travail sûre et une posture correcte du corps
permettent le plein contrôle de l’outil pneumatique en cas de situations imprévues.
ATTENTION
IL EST IMPORTANT DE LIRE INTÉGRALEMENT LE PRÉSENT MANUEL AVANT D’UTILISER
L’OUTIL PNEUMATIQUE. LE NON-RESPECT DES NORMES DE SÉCURITÉ ET DES
INSTRUCTIONS D’UTILISATION PEUT PROVOQUER DE GRAVES ACCIDENTS.
Ne pas porter de vêtements larges. Ne pas porter de bracelets ou de chaînettes. Faire en sorte que la chevelure, les vêtements et
les gants soient toujours loin des parties en mouvement. Les vêtements larges, les bijoux ou les cheveux longs peuvent être
entraînés dans les parties en mouvement.
Ne pas respirer directement l’air d’échappement et éviter qu’il n’atteigne les yeux. L’air d’échappement de l’outil pneumatique peut
contenir de l’eau, de l’huile, des particules métalliques et des impuretés qui peuvent représenter des risques.
UTILISATION CORRECTE DES CLÉS À CHOCS À RENVOI D’ANGLE PNEUMATIQUES
Pour bloquer et soutenir la pièce travaillée, utiliser des dispositifs de serrage ou des étaux. Ne pas tenir la pièce travaillée dans la
main ou bloquée avec le corps : de cette manière la sécurité du travail n’est pas garantie.
Ne pas soumettre l’outil pneumatique à une surcharge. Effectuer les travaux en utilisant exclusivement l’outil pneumatique
explicitement prévu pour le cas.
Contrôler systématiquement l’intégrité de la machine. N’utiliser aucun outil pneumatique dont l’interrupteur de mise en marche/arrêt
est défectueux. Un outil pneumatique qui ne peut plus être arrêté ou mis en marche est dangereux et doit être réparé.
Effectuer les réglages de la clé à chocs à renvoi d’angle pneumatique lorsque la machine est arrêtée. Couper systématiquement
l’arrivée d’air en cas d’inutilisation. Cette mesure de prévention empêche la mise en marche accidentelle de l’outil pneumatique.
Lorsque les outils pneumatiques ne sont pas utilisés, les garder hors de portée des enfants. Ne pas permettre aux personnes qui
n’ont pas lu les présentes instructions d’utiliser l’outil pneumatique.
Effectuer soigneusement le contrôle de l’outil pneumatique en s’assurant que les parties mobiles de l’outil fonctionnent
parfaitement, qu’elles ne se bloquent pas et qu’il n’y ait pas d’éléments cassés ou endommagés susceptibles d’en empêcher le
fonctionnement. Faire réparer les pièces endommagées avant l’utilisation de l’outil pneumatique.
Utiliser systématiquement des douilles à chocs qui se trouvent dans de bonnes conditions.
L’outil pneumatique ne doit pas être modifié. Les modifications peuvent réduire l’efficacité des mesures de sécurité et augmenter
l
es risques pour l’opérateur.
Faire réparer l’outil pneumatique seulement et exclusivement par un personnel spécialisé et en utilisant uniquement des pièces de
rechange originales.
INDICATIONS DE SÉCURITÉ POUR LES CLÉS À CHOCS À RENVOI D’ANGLE PNEUMATIQUES
Contrôler si la plaque d’identification est lisible. Si besoin est, se procurer une plaque de remplacement chez le fabricant.
Lors de l’utilisation de la clé à chocs à renvoi d’angle, d’éventuelles ruptures accidentelles des accessoires peuvent projeter des
éclats.
L’opérateur et le personnel préposé à la maintenance doivent être en mesure de gérer physiquement le poids et la puissance de
l’outil pneumatique.
Il est important d’être prêts à réagir en cas de mouvements soudains de la clé à chocs à renvoi d’angle pneumatique dus au
blocage ou à la rupture de l’outil de travail. Tenir fermement l’outil pneumatique et placer le corps et les bras dans une position
apte à compenser ces mouvements. Ces mesures peuvent prévenir les lésions.
Éviter le contact avec des éléments en mouvement de l’outil car ils peuvent causer des lésions.
S’assurer que le sens de rotation de la clé à chocs à renvoi d’angle pneumatique soit approprié à l’utilisation.
En cas d’interruption de l’arrivée d’air ou d’une pression de fonctionnement réduite, arrêter l’outil. Contrôler la pression d’exercice
et remettre en marche lorsque la pression redevient optimale.
En utilisant l’outil de coupe, il est possible que l’opérateur, en accomplissant les activités liées à son travail, éprouvent des
sensations désagréables au niveau des mains, des bras, des épaules et de la zone du cou. Le fait d’adopter une position
confortable, d’éviter les positions incorrectes et de changer de posture peut aider à éviter les gênes et la fatigue.
Attention au fonctionnement prolongé de l’outil pneumatique : une partie de l’outil et la douille peuvent devenir chaudes. Utiliser
des gants de protection.
Pendant l’utilisation de l’outil pneumatique sur la pièce à travailler, le personnel est exposé à des bruits parfois nuisibles. Une
analyse photométrique est nécessaire pour définir l’attribution correcte de l’équipement spécifique de protection individuelle de
l’ouïe à utiliser.
Si l’analyse effectuée révèle que l’exposition quotidienne aux vibrations générées pendant l’utilisation de l’outil pneumatique
dépasse la valeur limite d’action prévue par la norme en vigueur dans le pays concerné, il est nécessaire d’utiliser des gants anti-
vibrations préSi l’analyse effectuée révèle que l’exposition quotidienne aux vibrations générées pendant l’utilisation de l’outil
pneumatique dépasse la valeur limite d’action prévue par la norme en vigueur dans le pays concerné, il est nécessaire d’utiliser
des gants anti-vibrations prévus à cet effet.
Si l’on constate que la peau des doigts est engourdie ou qu’elle blanchit, si l’on ressent des fourmillements ou une douleur,
interrompre l’utilisation de l’outil pneumatique, informer l’employeur et consulter un médecin.
Tenir l’outil pneumatique de manière non excessivement ferme mais sûre, en tenant compte des forces de réactions nécessaires
de la main.
Ne jamais transporter l’outil pneumatique en le tenant par le tuyau flexible.
ÉQUIPEMENTS DE PROTECTION INDIVIDUELLE PRÉVUS LORS DE LUTILISATION DE LOUTIL PNEUMATIQUE
Le non-respect des recommandations suivantes peut causer des lésions physiques et/ou des pathologies.
CARACTÉRISTIQUES TECHNIQUES
EMBOUT DOUILLE 1/2“
CAPACITÉ VIS/ÉCROU (8.8) M14 - 21 mm
CAPACITÉ VIS/ÉCROU (12.9) M12 - 19 mm
VITESSE À VIDE 4700 tours/min
COUPLE MAXIMUM 240 Nm
FILETAGE D'ARRIVÉE D'AIR 1/4” GAS Conique
PRESSION MAXIMUM 6,2 bar
CONSOMMATION MAXIMUM D'AIR 190 l/min
POIDS 2,1 kg
LONGUEUR 355 mm
MASSES MAILLETS TYPE À SIMPLE FRAPPE
NIVEAU DE PRESSION ACOUSTIQUE 89.4 dB(A) (EN ISO 15744)
NIVEAU DE PUISSANCE ACOUSTIQUE 100.4 dB(A) (EN ISO 15744)
NIVEAU DE VIBRATIONS 8.63 m/s
2
(ISO 28927-2)
LÉGENDE
a : filetage d'arrivée d'air 1/4” GAS conique
b : touche de mise en marche de la clé à chocs à renvoi d’angle
c : levier d’inversion du cliquet
d : sélecteur de couple min. – max
e : lubrification huile
f : graissage
INSTRUCTIONS DE MONTAGE DES DISPOSITIFS
Branchement à larrivée dair
Pour une utilisation correcte de l’outil pneumatique, respecter toujours la pression maximum de 6,2 bar mesurée à l’entrée de l’outil.
Alimenter l’outil pneumatique avec de l’air propre et sans condensation (image 2). Une pression trop élevée ou la présence d’humidité
dans l’air d’alimentation réduisent la durée des pièces mécaniques et peuvent causer des dommages à l’outil.
Autres équipements de protection individuelle à utiliser en fonction des valeurs relees au cours de l’analyse d’hygiène
environnementale/des risques si les valeurs dépassent les limites prévues par les normes en vigueur.
PORTER SYSTÉMATIQUEMENT DES ÉQUIPEMENTS DE PROTECTION DE L’OUÏE PENDANT
L’UTILISATION DE L’OUTIL PNEUMATIQUE.
PORTER SYSTÉMATIQUEMENT DES LUNETTES DE PROTECTION PENDANT L’UTILISATION DE
L’OUTIL PNEUMATIQUE OU PENDANT L’ACTIVITÉ DE MAINTENANCE.
UTILISER SYSTÉMATIQUEMENT DES GANTS DE PROTECTION CONTRE LES AGENTS
PHYSIQUES PENDANT L’UTILISATION DE L’OUTIL PNEUMATIQUE.
UTILISER SYSTÉMATIQUEMENT DES CHAUSSURES DE SÉCURITÉ.
UTILISER DES GANTS ANTI-VIBRATION PENDANT L’UTILISATION DE L’OUTIL PNEUMATIQUE
SUITE À UNE ANALYSE SPÉCIFIQUE EN FONCTION DU NIVEAU D’EXPOSITION QUOTIDIENNE
AUX VIBRATIONS DU SYSTÈME MAIN-BRAS.
UTILISATION
Mise en marche / Arrêt
Pour mettre l’outil pneumatique en marche, appuyer sur le bouton de mise en marche (image 4) en maintenant la pression pendant
l’exécution du travail. En relâchant la touche, l’outil pneumatique s’arrête presque immédiatement.
Contrôler la position de l’inverseur de rotation à levier avant d’actionner l’outil pneumatique de sorte à connaître le sens de rotation.
Réglage du sens de rotation
La clé à chocs à renvoi d’angle pneumatique prévoit le sens de rotation horaire et antihoraire (image 3) :
sens horaire - vue du côté de l’opérateur
sens antihoraire - vue du côté de l’opérateur
Sélectionner le sens de rotation par le biais du levier d’inversion, avec les possibilités suivantes :
Sélection • couple minimum de vissage (environ 1/3 couple max)
Sélection •• couple maximum de vissage (environ 2/3 couple max)
Sélection couple maximum de dévissage (couple max)
Fixer la douille à chocs souhaitée sur la carrée mâle, en s’assurant du juste positionnement.
Interrompre systématiquement l’arrivée d’air avant d’effectuer des opérations d’introduction d’outils ou de faire des réglages. Cette
mesure de prévention empêche la mise en marche accidentelle de l’outil pneumatique.
Lubrification/Graissage
Pour obtenir un usage optimal, relier l’outil pneumatique à un groupe filtre-lubrificateur de ligne à micro-brouillard “(art. Beta 1919F1/4)
réglé à deux gouttes par minute. Dans ce cas, le rendement sera supérieur et l’usure des pièces mécaniques sera limitée.
En l’absence de lubrificateur dans la ligne, introduire périodiquement directement dans l’outil pneumatique une huile ISO 32 à travers
l’orifice d’arrivée d’air (image 6).
Il est par ailleurs nécessaire d’effectuer périodiquement un graissage du cliquet de la clé à chocs à renvoi d’angle, par le biais de la
buse de graissage, en utilisant une graisse EP2 (image 5).
MAINTENANCE
Les interventions de maintenance et de réparation doivent être effectuées par un personnel spécialisé. Pour ces interventions, vous
pouvez vous adresser au centre des réparations de Beta Utensili S.p.A.
ÉCOULEMENT
L’outil pneumatique, les accessoires et les emballages doivent être envoyés à un centre d’écoulement des déchets, conformément aux
lois en vigueur du pays où vous vous trouvez.
GARANTIE
Cet outil est fabriqué et testé conformément aux normes actuellement en vigueur dans la Communauté Européenne et est couvert par
une garantie de 12 mois pour une utilisation professionnelle et de 24 mois pour une utilisation non professionnelle.
Toutes les pannes dues à un défaut matériel ou de production seront réparées, en ajustant ou en remplaçant les pièces défectueuses à
notre discrétion.
La réalisation d’une ou de plusieurs interventions pendant la période de garantie n’en modifie pas la date d’échéance.
La garantie ne couvre pas les problèmes dus à l’usure des composants, à un usage erroné ou incorrect de l’outil, aux ruptures causées
pas des coups et/ou des chutes. La garantie ne s’appliquera pas en cas de modifications ou d’altérations de l’outil pneumatique ou
bien si celui-ci est envoyé à l’assistance technique démonté.
Tous les dommages causés aux personnes et/ou aux biens, directs et/ou indirects et de quelque genre ou nature que ce soit, sont
exclus de la garantie.
DÉCLARATION DE CONFORMITÉ
Nous déclarons, en en assumant la pleine responsabilité, que le produit décrit est conforme à toutes les dispositions de la Directive
Machines 2006/42/CE et modifications et intégrations successives, ainsi qu’à la norme
EN ISO 11148-6
Le Fascicule Technique est disponible chez :
BETA UTENSILI S.P.A.
Via A. Volta 18 - 20845 Sovico (MB) - ITALIE
Nom et fonction du Responsable
MASSIMO CICERI
(Administrateur Délégué)
BETA UTENSILI S.P.A. Date 01/01/2015
Via A. Volta 18
20845 Sovico (MB)
ITALIE
Beta
NL
GEBRUIKSHANDLEIDING VOOR HAAKSE SLAGMOERSLEUTELS GEPRODUCEERD DOOR:
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
ITALIË
Oorspronkelijk in de ITALIAANSE taal geschreven documentatie.
Bewaar de veiligheidsinstructies zorgvuldig en geef ze aan het personeel dat de boormachine gebruikt.
GEBRUIKSDOEL
De haakse slagmoersleutel is bestemd voor het volgende gebruik:
de montage van schroefdraadverbindingen
het aan- en losdraaien met behulp van slagdoppen
de haakse slagmoersleutel kan ook op plaatsen in de openlucht worden gebruikt, waar hij is blootgesteld aan water en wind
De volgende handelingen zijn niet toegestaan:
het gebruik van dopsleutels is verboden
het gebruik van koppelingen en verlengstukken is verboden, aangezien deze het vermogen van de slagmoersleutel verminderen
en de kans groter maken dat hij kapotgaat
het gebruik in omgevingen met mogelijk explosieve atmosferen is verboden
het is verboden de startknop met plakband of banden vast te zetten
VEILIGHEID VAN DE WERKPLEK
Kijk goed uit voor de oppervlakken die glad kunnen worden door het gebruik van de machine en voor het gevaar om over de
flexibele luchtslang te struikelen.
Tijdens het gebruik van het pneumatische gereedschap voor werkzaamheden die op een bepaalde hoogte moeten worden verricht,
moeten alle voorzorgsmaatregelen worden getroffen om het gevaar voor andere werknemers, veroorzaakt door mogelijk vallen van
gereedschap, op te heffen of tot een minimum te beperken(bijvoorbeeld door het werkgebied af te schermen, duidelijke signalering,
enz.).
Gebruik het pneumatische gereedschap niet in omgevingen met mogelijk explosieve atmosferen, omdat er vonken kunnen
ontstaan, die stof of damp in brand kunnen laten vliegen.
Voorkom contact met onder spanning staande apparatuur, aangezien het pneumatische gereedschap niet is geïsoleerd en
aanraking met onder spanning staande onderdelen een elektrische schok kan veroorzaken.
Voorkom dat kinderen of bezoekers in de buurt van de werkplek kunnen komen terwijl met het pneumatische gereedschap wordt
gewerkt. De aanwezigheid van andere personen leidt af waardoor men de controle over het pneumatische gereedschap kan
verliezen.
VEILIGHEID VAN PNEUMATISCH GEREEDSCHAP
Richt de luchtstroom nooit op uzelf of op andere personen. Perslucht kan ernstig letsel veroorzaken.
Controleer de koppelingen en de toevoerleidingen. Alle groepen, koppelingen en flexibele slangen moeten conform de technische
gegevens met betrekking tot druk en luchtstroom worden geïnstalleerd. Een te lage druk schaadt de werking van het pneumatische
gereedschap. Een te hoge druk kan schade en/of letsel veroorzaken.
Vouw flexibele slangen niet dubbel en knel ze niet af. Gebruik geen oplosmiddelen en mijd scherpe randen. Bescherm de slangen
tegen hitte, olie en draaiende delen. Vervang een beschadigde flexibele slang onmiddellijk. Een defecte toevoerleiding kan
ongecontroleerde bewegingen van de persluchtslang veroorzaken. Door de lucht opgetilde stof of spaanders kunnen letsel aan de
ogen veroorzaken. Verzeker u ervan dat de slangklemmen voor flexibele slangen altijd goed vastzitten.
AANWIJZINGEN VOOR DE VEILIGHEID VAN HET PERSONEEL
We drukken u op het hart uw aandacht er altijd maximaal bij te houden en u op uw eigen handelingen te concentreren. Gebruik het
pneumatische gereedschap niet als u moe bent of onder invloed van drugs, alcohol of medicijnen.
Gebruik altijd de volgende persoonlijke beschermingsmiddelen:
Een beschermende bril;
Veiligheidsschoenen;
Oorbescherming;
Beschermende handschoenen voor fysische agentia;
Trillingsdempende handschoenen, te gebruiken na een specifiek onderzoek naar het niveau van de dagelijkse blootstelling van
het hand/armstelsel aan de trillingen.
LET OP
BELANGRIJK: LEES DEZE HANDLEIDING HELEMAAL DOOR ALVORENS HET PNEUMATISCHE
GEREEDSCHAP TE GEBRUIKEN. INDIEN DE VEILIGHEIDSVOORSCHRIFTEN EN DE
AANWIJZINGEN NIET IN ACHT WORDEN GENOMEN, KUNNEN ZICH ERNSTIGE ONGEVALLEN
VOORDOEN.
Zorg ervoor dat u zich op een veilige plek bevindt en uw evenwicht op ieder moment behoudt. Een veilige werkplek en een
geschikte lichaamshouding maken het mogelijk het pneumatische gereedschap in onverwachte situaties beter te controleren.
Draag geen wijde kleding. Draag geen armbanden en kettingen. Houd haren, kleding en handschoenen buiten bereik van
bewegende delen. Wijde kleding, juwelen en lange haren kunnen in bewegende delen verstrikt raken.
Adem de afvoerlucht niet in en voorkom dat ze bij de ogen kan komen. De afvoerlucht van het pneumatische gereedschap kan
water, olie, metalen delen en onzuiverheden bevatten, die gevaar kunnen veroorzaken.
ZORGVULDIG GEBRUIK VAN PNEUMATISCHE HAAKSE SLAGMOERSLEUTELS
Om het stuk dat wordt bewerkt vast te zetten en te steunen, gebruikt u kleminrichtingen of een bankschroef. Houd het te bewerking
stuk niet met een hand vast en zet het niet met het lichaam vast. Op die manier kunt u niet veilig werken.
Overbelast het pneumatische gereedschap niet. Verricht uw werkzaamheden door uitsluitend het pneumatische gereedschap te
gebruiken dat hier specifiek voor is bedoeld.
Controleer altijd of de machine intact is. Gebruik geen enkel pneumatisch gereedschap waarvan de start/stopknop defect is. Een
pneumatisch gereedschap dat niet kan worden gestopt of gestart is gevaarlijk en moet worden gerepareerd.
Verricht de instellingen van de pneumatische slagmoersleutel bij stilstaand apparaat. Onderbreek altijd de luchttoevoer wanneer de
slagmoersleutel niet wordt gebruikt. Deze voorzorgsmaatregel voorkomt dat het pneumatische gereedschap per ongeluk kan
worden ingeschakeld.
Wanneer pneumatisch gereedschap niet wordt gebruikt, bewaart u het buiten bereik van kinderen. Sta niet toe dat het
pneumatische gereedschap wordt gebruikt door personen die deze aanwijzingen niet hebben gelezen.
Controleer het pneumatische gereedschap zorgvuldig en verzeker u ervan dat de bewegende delen van het gereedschap perfect
werken, dat ze niet vastlopen en dat er geen kapotte of beschadigde onderdelen zijn, die de werking ervan schaden. Laat de
kapotte onderdelen repareren voordat u het pneumatische gereedschap gebruikt.
Gebruik altijd slagdoppen die zich in goede staat bevinden.
Er mogen geen wijzigingen aan het pneumatische gereedschap worden aangebracht. Wijzigingen kunnen de efficiëntie van de
veiligheidsmaatregelen verminderen en de gevaren voor de gebruiker verhogen.
Laat het pneumatische gereedschap enkel en alleen door vakmensen met gebruik van originele reserveonderdelen repareren.
VEILIGHEIDSAANWIJZINGEN VOOR PNEUMATISCHE HAAKSE SLAGMOERSLEUTELS
Controleer of het identificatieplaatje leesbaar is. Schaf eventueel een nieuw plaatje bij de fabrikant aan om het te vervangen.
Tijdens het gebruik van de slagmoersleutel kunnen de afzonderlijke accessoires kapotgaan, waardoor stukken met hoge snelheid
kunnen worden weggeslingerd.
De gebruiker en het onderhoudspersoneel moeten in staat zijn het gewicht en het vermogen van het pneumatische gereedschap
fysiek aan te kunnen.
Het is belangrijk voorbereid te zijn op onverwachte bewegingen van de pneumatische haakse slagmoersleutel veroorzaakt door
vastlopen of kapotgaan van het gereedschap. Houd het pneumatische gereedschap altijd stevig vast en houd uw lichaam en de
armen in een houding waarmee u deze bewegingen kunt compenseren. Deze maatregelen kunnen letsel voorkomen.
Voorkom aanraking met bewegende delen van het gereedschap aangezien ze letsel kunnen veroorzaken.
Verzeker u ervan dat de draairichting van de pneumatische haakse slagmoersleutel in overeenstemming is met het gebruik.
Schakel het gereedschap uit bij een onderbreking van de luchttoevoer of een verminderde werkdruk. Controleer de werkdruk en
als die optimaal is, schakelt u het gereedschap weer in.
Tijdens het gebruik van het pneumatische gereedschap kan de gebruiker bij de werkzaamheden een vervelend gevoel in de
handen, armen, schouders en het gebied van de nek krijgen. Neem een prettige houding aan en vermijd onhandige houdingen.
Van houding veranderen kan helpen om pijn en vermoeidheid te voorkomen.
Let op bij langdurig gebruik van het pneumatische gereedschap: delen van het gereedschap zelf en de dopsleutel kunnen heet
worden. Gebruik beschermende handschoenen.
Tijdens het gebruik van het pneumatische gereedschap op het stuk dat moet worden bewerkt, ontstaan geluiden, die soms
schadelijk kunnen zijn voor het personeel dat eraan is blootgesteld. Er is een goed geluidsonderzoek nodig om de juiste individuele
gehoorbeschermers (oorbeschermer) vast te stellen, die moeten worden gebruikt.
Wanneer uit het specifiek verrichte onderzoek blijkt dat de dagelijkse blootstelling aan de trillingen veroorzaakt door het gebruik
van het pneumatische gereedschap de grenswaarden overschrijdt die in de geldende voorschriften van het betreffende land staan,
moeten speciale trillingsdempende handschoenen worden gebruikt.
Wanneer u merkt dat de huid van de vingers gevoelloos of wit wordt, tintelt of pijn doet, stopt u het werk met het pneumatische
gereedschap, informeert u uw werkgever en raadpleegt u een arts.
Houd het pneumatische gereedschap niet overdreven stevig, maar wel veilig vast en houd hierbij rekening met de noodzakelijke
reactiekracht van de hand.
Vervoer het pneumatische gereedschap nooit door het aan de flexibele slang vast te houden.
INDIVIDUELE BESCHERMINGSMIDDELEN DIE NODIG ZIJN TIJDENS HET GEBRUIK VAN HET PNEUMATISCHE GEREEDSCHAP
Niet inachtneming van de volgende waarschuwingen kan lichamelijk letsel en/of ziektes veroorzaken.
TECHNISCHE GEGEVENS
AANSLUITING 1/2“
BOUTCAPACITEIT (8.8) M14 - 21 mm
BOUTCAPACITEIT (12.9) M12 - 19 mm
SNELHEID ONBELAST 4700 toeren/min
MAX. AANHAALKOPPEL 240 Nm
LUCHTAANSLUITING 1/4” GAS conisch
MAXIMUMDRUK 6,2 bar
MAXIMUM LUCHTVERBRUIK 190 l/min
GEWICHT 2,1 kg
LENGTE 355 mm
SLAGGEWICHT VAN HET TYPE ENKELE HAMER
GELUIDSDRUKNIVEAU 89.4 dB(A) (EN ISO 15744)
GELUIDSNIVEAU 100.4 dB(A) (EN ISO 15744)
TRILLINGSNIVEAU 8.63 m/s
2
(ISO 28927-2)
LEGENDA
a: luchtaansluiting 1/4” GAS conisch
b: startknop slagmoersleutel
c: omschakelknop ratel
d: schakelaar min. – max. aanhaalmoment
e: smering olie
f: smering
MONTAGE-INSTRUCTIES
De luchttoevoer aansluiten
Voor een optimaal gebruik van het pneumatische gereedschap dient men zich altijd aan de maximumdruk van 6,2 bar te houden,
gemeten aan de inlaat van het gereedschap. Voed het pneumatische gereedschap met schone lucht en zonder condens
(afbeelding 2). Een te hoge druk of de aanwezigheid van vocht in de toevoerlucht verkorten de levensduur van de mechanische
onderdelen en kunnen het gereedschap beschadigen.
Andere persoonlijke beschermingsmiddelen die moeten worden gebruikt, afhankelijk van de waarden die zijn gevonden bij het
onderzoek van de milieuhygiëne /risicoanalyse indien de waarden de maximumwaarden overschrijden, die in de geldende
voorschriften staan.
DRAAG ALTIJD GEHOORBESCHERMING WANNEER U HET PNEUMATISCHE GEREEDSCHAP
GEBRUIKT
DRAAG ALTIJD EEN BESCHERMENDE BRIL WANNEER U HET PNEUMATISCHE GEREEDSCHAP
GEBRUIKT OF ONDERHOUDSWERKZAAMHEDEN VERRICHT
GEBRUIK ALTIJD BESCHERMENDE HANDSCHOENEN VOOR FYSISCHE AGENTIA TIJDENS HET
GEBRUIK VAN HET PNEUMATISCHE GEREEDSCHAP
GEBRUIK ALTIJD VEILIGHEIDSSCHOENEN
GEBRUIK TRILLINGSDEMPENDE HANDSCHOENEN TIJDENS HET GEBRUIK VAN HET
PNEUMATISCHE GEREEDSCHAP NA EEN SPECIFIEK ONDERZOEK NAAR HET NIVEAU VAN DE
DAGELIJKSE BLOOTSTELLING VAN HET HAND/ARMSTELSEL AAN DE TRILLING
GEBRUIK
Start / Stop
Om het pneumatische gereedschap te starten, drukt u op de startknop (afbeelding 4) en houdt u hem tijdens het verrichten van het
werk ingedrukt. Wanneer u de knop loslaat, stopt het pneumatische gereedschap onmiddellijk.
Controleer de stand van de omkeerhendel voordat u het pneumatische gereedschap inschakelt, zodat u weet op welke draairichting hij
staat.
De draairichting instellen
De pneumatische haakse slagmoersleutel kan met de klok mee en tegen de klok in draaien (afbeelding 3):
met de klok mee - gezien vanaf de kant van de gebruiker
tegen de klok in - gezien vanaf de kant van de gebruiker
Kies de draairichting met behulp van de omschakelknop. Het biedt de volgende mogelijkheden:
keuze • minimum aanhaalkoppel (ongeveer 1/3 max. aanhaalkoppel)
keuze •• maximum aanhaalkoppel (ongeveer 2/3 max. aanhaalkoppel)
keuze maximum loshaalkoppel (maximumkoppel)
Breng de gewenste slagdop op het aandrijfvierkant met tap aan en verzeker u ervan dat hij goed is aangebracht.
Onderbreek altijd de luchttoevoer voordat u het gereedschap aanbrengt of afstellingen verricht. Deze voorzorgsmaatregel voorkomt dat
het pneumatische gereedschap per ongeluk kan worden ingeschakeld.
Smeren
Het pneumatische gereedschap moet op een filter-smeersysteem van de lijn worden aangesloten (aangeraden wordt art. Beta
1919F1/4) met microverneveling, afgesteld op twee druppels per minuut. In dat geval is er een groter rendement en slijten de
mechanische onderdelen minder snel.
Mocht de lijn niet voorzien zijn van smering dan moet regelmatig olie ISO 32 via de luchttoevoeropening direct in het pneumatische
gereedschap worden gedruppeld (afbeelding 6).
Bovendien moet de ratel van de slagmoersleutel regelmatig via de smeeropening met EP2 vet worden gesmeerd (afbeelding 5).
ONDERHOUD
Onderhoudswerkzaamheden en reparaties mogen uitsluitend door vakmensen worden verricht. Wend u voor deze werkzaamheden tot
het reparatiecenter van Beta Utensili S.P.A.
AFDANKEN
Het pneumatische gereedschap, de accessoires en verpakkingen moeten volgens de wetten van het land waarin u zich bevindt naar
een centrum voor afvalverwerking worden gestuurd.
GARANTIE
Dit gereedschap is volgens de op dit moment in de Europese Unie geldende voorschriften getest en heeft 12 maanden garantie bij
professioneel gebruik of 24 maanden bij niet professioneel gebruik.
Storingen veroorzaakt door materiaal- of fabrieksfouten worden naar ons goeddunken ofwel gerepareerd of de defecte onderdelen
worden vervangen.
Eén of meerdere reparaties tijdens de garantieperiode wijzigt de verloopdatum ervan niet.
Defecten veroorzaakt door slijtage, een verkeerd of oneigenlijk gebruik, of door vallen en/of stoten worden niet door de garantie gedekt.
De garantie vervalt wanneer er wijzigingen worden aangebracht, wanneer er met het pneumatische gereedschap wordt geknoeid en
wanneer het gedemonteerd naar de servicedienst wordt gestuurd.
Schade toegebracht aan personen en / of voorwerpen van welke aard en / of natuur, direct en / of indirect is uitdrukkelijk uitgesloten.
VERKLARING VAN OVEREENSTEMMING
We verklaren onder eigen verantwoordelijkheid dat het beschreven product voldoet aan alle bepalingen van de Machinerichtlijn
2006/42/EG en bijbehorende wijzigingen en ook aan de volgende normen:
EN ISO 11148-6
Het technische dossier is verkrijgbaar bij:
BETA UTENSILI S.P.A.
Via A. Volta 18 - 20845 Sovico (MB) - ITALIË
Naam en functie van de verantwoordelijke
MASSIMO CICERI
(Algemeen directeur)
BETA UTENSILI S.P.A. Datum 01/01/2015
Via A. Volta 18
20845 Sovico (MB)
ITALIË
Beta
D
BEDIENUNGSANLEITUNG FÜR DRUCKLUFT-WINKELSCHLAGSCHRAUBER HERGESTELLT VON:
BETA UTENSILI S.P.A.
Via A. Volta 18,
20845, Sovico (MB)
ITALIEN
Dokumentation Original in ITALIENISCHER SPRACHE verfasst.
Die Sicherheitsanweisungen sorgfältig aufbewahren und dem Bedienerpersonal übergeben.
BESTIMMUNGSZWECK
Der Druckluft-Winkelschlagschrauber ist für die folgenden Anwendungen bestimmt:
Zusammenbauen von Gewinde-Anschlussteilen
Einschrauben und Aufschrauben mittels Kraftsteckschlüssel
Verwendung auch im Freien, kann Wasser und Luft ausgesetzt sein
Nicht zulässig sind die folgenden Vorgänge:
Unzulässig ist die Verwendung von Handsteckschlüsseln
Unzulässig ist die Verwendung von Kupplungen und Verlängerungen, weil diese die Motorleistung des Schlagschraubers
verringern und die Gefahr von Brüchen erhöhen
Unzulässig ist der Gebrauch in explosionsfähiger Arbeitsumgebung
Es ist verboten, den Betätigungsknopf mit Klebeband oder Schellen zu blockieren.
SICHERHEIT DES ARBEITSPLATZES
Mit Vorsicht vorgehen auf Oberflächen, die durch den Gebrauch der Maschine glatt bzw. rutschig werden können, und aufpassen,
nicht über die Druckluftleitung zu stolpern.
Während des Gebrauchs des Werkzeugs in Höhe alle Sicherheitsmaßnahmen treffen, um die Risiken hinsichtlich möglichen
Herunterfallen der Gerätschaften zu beseitigen oder zu reduzieren (zum Beispiel Abgrenzung des Arbeitsbereichs, angemessene
Beschilderung usw.).
Das Druckluftwerkzeug nicht in explosionsfähiger Umgebung verwenden, da sich Funken entwickeln können, die Staub oder
Dämpfe entflammen könnten.
Den Kontakt mit unter Spannung stehenden Geräten vermeiden, da das Druckluftwerkzeug nicht isoliert ist und der Kontakt mit
unter Spannung stehenden Teilen einen elektrischen Schlag verursachen kann.
Dafür sorgen, dass sich Kinder oder Besucher nicht dem Arbeitsplatz nähern können, wenn Sie mit dem Druckluftwerkzeug
arbeiten. Der Aufenthalt anderer Personen lenkt bei der Arbeit ab, wodurch die Kontrolle über das Druckluftwerkzeug verloren
gehen könnte.
SICHERHEIT DER DRUCKLUFTWERKZEUGE
Den Druckluftstrahl niemals auf sich selbst oder auf andere Personen richten. Die Druckluft kann schwere Verletzungen
verursachen.
Die Anschlüsse und Luftzufuhrleitungen stets überprüfen. Alle Aggregate, Kupplungen und Schläuche sind entsprechend den
technischen Daten hinsichtlich Druck und Luftfluss zu installieren. Ein zu niedriger Druck beeinträchtigt den korrekten Betrieb des
Druckluftwerkzeugs, ein zu hoher Druck führt zu Schäden und/oder Verletzungen.
Die Schläuche nicht biegen oder drücken, keine Lösemittel oder scharfe Kanten verwenden. Schützen Sie die Leitungen vor Hitze,
Öl und drehenden Teilen. Bei Beschädigungen eines Schlauchs ist dieser unverzüglich zu ersetzen. Eine fehlerhafte Zufuhrleitung
kann zu unkontrollierbaren Bewegungen der Druckluftleitung führen. Von der Luft aufgewirbelte Späne oder Staub können die
Augen verletzen. Sicherstellen, dass die Schellen für die Schläuche stets gut befestigt sind.
HINWEISE FÜR DIE SICHERHEIT DES PERSONALS
Bei der Arbeit mit Druckluftwerkzeugen ist stets mit höchster Vorsicht und Konzentration vorzugehen. Auf keinen Fall mit dem
Druckluftwerkzeug arbeiten, wenn Sie müde sind oder unter Drogen-, Alkohol oder Medikamenteneinfluss stehen.
Stets die persönlichen Sicherheitsausrüstungen tragen:
Schutzbrille;
Sicherheitsschuhe;
Gehörschutz;
Schutzhandschuhe gegen physikalische Einwirkungen;
Vibrationsschutzhandschuhe, zu verwenden nach spezifischer Analyse der Tages-Schwingungsbelastung bezüglich Vibrationen
für Hand-Arm.
ACHTUNG
VOR GEBRAUCH DES DRUCKLUFTWERKZEUGS DIESE BEDIENUNGSANLEITUNGEN
VOLLSTÄNDIG LESEN. DIE NICHTBEACHTUNG DER SICHERHEITSVORSCHRIFTEN UND DER
BEDIENUNGSANLEITUNGEN KANN SCHWERE VERLETZUNGEN VERURSACHEN.
Halten Sie den Körper im Gleichgewicht und suchen Sie einen sicheren Stand. Eine sichere Arbeitsposition und eine korrekte
Körperhaltung erlauben eine bessere Kontrolle über das Druckluftwerkzeug im Falle von unerwarteten Situationen.
Keine weite Kleidung, Armbänder, Armreife und Halsketten tragen. Haare, Kleidung und Handschuhe in Sicherheitsabstand zu sich
drehenden Teilen halten. Weite Kleidung, Schmuck oder lange Haare können sich in den drehenden Teilen verfangen.
Nicht direkt Abluft einatmen und vermeiden, dass sie in die Augen gerät. Die Abluft des Druckluftwerkzeugs enthält Wasser, Öl,
Metallteilchen und Unreinheiten, die gefährlich sind.
KORREKTER GEBRAUCH VON DRUCKLUFT-WINKELSCHLAGSCHRAUBERN
Zum Blockieren und Stützen des Werkstücks Spannvorrichtungen oder Schraubstöcke verwenden. Halten Sie das Werkstück
weder mit der Hand noch mit dem Körper fest, da Sie sich so in Gefahr bringen könnten.
Das Druckluftwerkzeug nicht überlasten. Das für die durchzuführende Arbeit geeignete Druckluftwerkzeug verwenden.
Stets die Unversehrtheit der Maschine überprüfen. Verwenden Sie keine Druckluftwerkzeuge deren Start-/Stopp-Schalter fehlerhaft
ist. Ein Druckluftwerkzeug, das weder angehalten noch gestartet werden kann, ist gefährlich und muss repariert werden.
Einstellungen nur beim stillstehendem Druckluft-Schlagschrauber durchführen. Bei Nichtgebrauch trennen Sie das Werkzeug von
der Luftleitung. Mit dieser Maßnahme wird das unbeabsichtigte Einschalten des Druckluftwerkzeugs ausgeschlossen.
Bei Nichtgebrauch der Druckluftwerkzeuge diese außer Reichweite von Kindern aufbewahren. Das Druckluftwerkzeug darf auf
keinen Fall von Personen benutzt werden, die nicht die Bedienungsanleitung gelesen haben.
Das Druckluftwerkzeug sorgfältig überprüfen und sicherstellen, dass die beweglichen Teile des Werkzeugs korrekt funktionieren,
sie nicht klemmen und keine Teile Brüche oder Beschädigungen aufweisen, die den korrekten Betrieb beeinträchtigen könnten.
Lassen Sie die beschädigten Teile vor Verwendung des Druckluftwerkzeugs reparieren.
Ausschließlich Kraftsteckschlüssel in gutem Zustand verwenden.
Das Druckluftwerkzeug darf nicht verändert werden. Die eventuellen Umänderungen verringern die Sicherheitsmaßnahmen und
e
rhöhen das Risiko für den Bediener.
Das Druckluftwerkzeug darf ausschließlich von Fachpersonal repariert werden, das nur Original-Zubehörteile verwendet.
SICHERHEITSHINWEISE FÜR DRUCKLUFT-WINKELSCHLAGSCHRAUBER
Kontrollieren Sie, dass das Typenschild lesbar ist, ist das nicht der Fall, fordern Sie beim Hersteller ein Neues an.
Während des Gebrauchs des Schlagschraubers können bei versehentlichem Bruch des Zubehörs Teile mit hoher Geschwindigkeit
herausgeschleudert werden.
Das Bediener- und Wartungspersonal muss körperlich für den Umgang mit Größe, Gewicht und Leistungsvermögen des
Druckluftwerkzeugs in der Lage sein.
Es ist wichtig, auf unerwartete Bewegungen des Druckluft-Winkelschlagschraubers wegen der Blockierung oder des Brechens des
Werkzeugs vorbereitet zu sein. Halten Sie das Druckluftwerkzeug gut fest und bringen Sie Ihren Körper und die Arme in eine
Stellung, die es zulässt, dass Sie die Bewegung des Werkzeugs kompensieren. Diese Maßnahmen können Verletzungen
verhindern.
Den Kontakt mit sich drehenden Teilen des Werkzeugs vermeiden, weil diese Verletzungen verursachen können.
Überprüfen Sie, dass die Drehrichtung des Druckluft-Winkelschlagschraubers richtig eingestellt ist.
Im Fall einer Unterbrechung der Luftzufuhr oder eines reduzierten Betriebsdrucks ist das Werkzeug auszuschalten. Kontrollieren
Sie den Betriebsdruck und bei optimalem Betriebsdruck das Werkzeug erneut starten.
Nach lang andauernder Benutzung des Druckluftwerkzeugs ist es möglich, dass der Bediener bei der Arbeit durch die extremen
Schwingungen ein Kribbeln in den Händen oder ein unangenehmes Gefühl in Armen, Schultern und im Nackenbereich verspürt.
Eine bequeme Position oder die Haltung ändern helfen diese unangenehmen Ermüdungserscheinungen zu vermeiden.
Achtung: Bei längerem Gebrauch des Druckluftwerkzeugs können ein Teil des Werkzeugs und der Steckschlüssel heiß werden.
Verwenden Sie Schutzhandschuhe.
Während des Gebrauchs des Druckluftwerkzeugs entwickeln sich Geräusche, die für den Bediener schädigend sein können. Um
die korrekte persönliche Schutzausrüstung (Gehörschutz) festzulegen, muss eine genaue Untersuchung des Geräuschpegels
vorgenommen werden.
Wenn eine spezifische Untersuchung ergibt, dass die Tages-Schwingungsbelastung während des Gebrauchs des
Druckluftwerkzeugs den von den geltenden Vorschriften im Benutzerland festgelegten Höchstwert überschreitet, müssen
spezifische Vibrationsschutzhandschuhe benutzt werden.
Wenn Sie merken sollten, dass die Haut der Finger weiß wird oder Taubheitsgefühle und Schmerzen eintreten, ist die Arbeit mit
dem Druckluftwerkzeug sofort einzustellen. Den Arbeitsgeber informieren und sich an einen Arzt wenden.
Halten Sie das Werkzeug sicher aber nicht zu fest in der Hand, da die erforderlichen Reaktionskräfte der Hand zu berücksichtigen
sind.
Das Druckluftwerkzeug niemals durch Ziehen des Schlauchs transportieren.
1 / 1

Beta 1927AN Istruzioni per l'uso

Categoria
Utensili elettrici
Tipo
Istruzioni per l'uso