ProLights PIXIEWASHXB Manuale utente

USER MANUAL

MANUALE UTENTE

PIXIEWASHXB

WASH MOVING HEAD

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 02-05/19

1

PIXIEWASHXB

• PIXIEWASHXB

• OS24 (2 pcs)

• Power cable

• Safety cable

• User manual

Packing content

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX addressing

3. 5 DMX configuration

3. 6 Wireless settings

3. 7 Ethernet

3. 8 Movement

3. 9 Screen

3. 10 Fixture settings

3. 11 Auto test

3. 12 Manual test

3. 13 Advanced

3. 14 Information on the device

3. 15 Dmx view

3. 16 DMX channels

3. 17 Construction of the DMX termination

3. 18 Connection of the DMX line

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

3

5

6

7

8

10

11

12

13

14

15

21

22

23

PIXIEWASHXB

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

.

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the ﬁxture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• The maximum temperature that can be reached on the external surface of the ﬁtting, in a thermally

steady state, is high. After power oﬀ, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

PIXIEWASHXB

- 1 - INTRODUCTION

1.1 DESCRIPTION

PIXIEWASHXB reinvents the concept of the moving LED wash light; bringing together the classic styling of

a traditional wash luminaire and applying the very latest innovations in the ﬁeld of LED technology. The

large frontal plano-convex lens delivers a stunning level of brightness and an exceptional zoom range

with a 1:8 ratio, combined with a proprietary 280W RGB and warm white LED module delivering a high-

quality white reproduction with high CRI and TLCI parameters as well an extremely precise colour tuning.

PIXIEWASHXB is an ideal solution for any application where users want a superior light quality but without

the view of multi-cell ﬁxtures. Being compact, fast and silent, the PIXIEWASHXB oﬀers unprecedented ﬂex-

ibility and is ideal for use in theatres, TV, corporate and festivals.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 280W RGB + Warm White

• CT: 6.500K

• CRI: > 92

• R9: > 94

• Luminous ﬂux: (6°) 3’670 lm - (45°) 3’795lm

• Lux: (6°) 29’900 lx - (45°) 1’590lx @3 m full

• Lux: (6°) 10’764 lx - (45°) 572lx @5 m full

• Source life expectancy: 70.000

• Other: TM-30-15RF/RG: 90 / 99 - TLCI: > 85

OPTICS

• Zoom: 6° - 45° motorised linear zoom

• Field angle: 11° - 48°

• Lens diameter: 125mm

• Lens type: high-quality glass lens optics

COLOUR SYSTEM

• Colour mixing: RGB + Warm White

• CTC: CTC control through independent DMX channel, + / - green and magenta correction and amber

shift activation by DMX

• White presets: 2.800 K - 8.000K

• Colour wheel: virtual colour wheel with presets

• Macros: several pre-build macros with adjustable speed

BODY

• Hardware on-board: OMEGA sockets for quick rigging (clamp included)

• Pan angle: 540°

• Tilt angle: 250°

• Pan/Tilt resolution: 8/16bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium die-casting

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, Art-Net, W-DMX

• DMX channels: 13 / 15 / 16 / 18 / 22 / 23 / 27channel

• W-DMX: included, wireless solution receiver

PIXIEWASHXB

4

• RDM: RDM ready for ﬁxture remote monitor and settings

• Display: LCD high resolution colour display with autoﬂip

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: diﬀerent dimming curves available

• Strobe / shutter: 1 - 30 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

• Flicker: ﬂicker free frequency with adjustable PWM

ELECTRICAL

• Power consumption: 338 W

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 338W

• Power consumption (at 120 V): 342W

• Output (at 230 V): 8 units on a single power line

• Output (at 120 V): 5 units on a single power line

• Power factor: pF 0,99 @120 V - pF 0,95 @230 V

PHYSICAL

Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and ﬁxing: any position with quick-lock omega brackets

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Data connection: Art-Net RJ45 IN/OUT

• Power connection: Seetronic powerCON waterproof IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 308x448x230mm

• Weight: 13,6kg

Technical drawing Fig.1

448

308 230

5

PIXIEWASHXB

1

2

3

4

5

6

8

9 10 11 12

111415

7

13

1. MOVING HEAD

2. ROTARY ARM

3. BASE

4. HANDLE

5. LED INDICATOR "POWER"

6. LED INDICATOR "DMX"

7. CONTROL PANEL with OLED

display and 4 button used to

access the control panel functions

and manage them.

8. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

9. POWER OUT (PowerCON

TRUE OUT): power output for

connection of multiple units in

series.

10. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

11. EtherCON CONNECTORS IN / OUT

signal.

12. DMX OUT (5-pole XLR): 1 = ground,

2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C.

13. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

14. ANTENNA

15. RUBBER FEET

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

PIXIEWASHXB

6

- 2 - INSTALLATION

2.1 MOUNTING

The PIXIEWASHXB may be set up on a solid and even surface. By means of the ﬁxing facilities of the base-

plate, the unit can also be mounted upside down to a cross arm. The base plate is shown in ﬁg.3. For ﬁxing,

stable mounting clips are required. According to the ﬁgure, the bolts of the brackets are placed into the

openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that

the unit is ﬁrmly ﬁxed to avoid vibration and slipping while operating. The mounting place must be of

suﬃcient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the ﬁxture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

CLAMPS

SAFETY

CABLE

OMEGA

BRACKETS

7

PIXIEWASHXB

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to re-

set all motors to their home position. Shortly after that the PIXIEWASHXB is ready for operation. To switch

oﬀ, disconnect the mains plug from the socket. For a more convenient operation it is recommended to

connect the unit to a socket which can be switched on and oﬀ via light switch.

NOTE: for factory default settings, the Calibrated function is active on the PIXIEWASHXB. Refer to paragraph

“Fixture Settings” (pag.12 and 13).

3.2 BASIC

The PIXIEWASHXB has a LCD display and 4 button used to access the control panel functions and manage

them (ﬁg.4).

Fig.4 - Functions of the buttons and display icons

UP

DOWN LEFT RIGHT

Increases the value

displayed or passes to

the previous item in a

menu

Decreases the value

displayed or passes to

the next item in the

menu

To enter in the main

menù or to return to the

top level

Confirms the displayed

value, or activates the

displayed function, or

enters the successive

menu

PIXIEWASHXB

8

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (1-512) Default: 1

DMX Mode

ð

STANDARD-13CH

STANDARD-15CH

STANDARD-16CH

EXTENDED-18CH

EXTENDED-22CH

EXTENDED-23CH

27 CH

Default:

EXTENDED

22CH

Wireless Setting

ð

Receive Oﬀ/On

ð

Off

On

Default :Oﬀ

Receive Reset

ð

No

Yes

Default :No

Wireless To DMX

ð

No

Yes

Default :Yes

Ethernet

ð

Universe

ð

0-255 Default: 0

Start Channel

ð

1-512 Default:1

IP Address

ð

2.133.139.215

Ethernet To DMX

ð

NO Default :Yes

2 SETUP

ð

Movement

ð

Pan Reverse

ð

No

Yes

Default: No

Tilt Reverse

ð

No

Yes

Default: No

Zoom Reverse

ð

No

Yes

Default: No

Pan Feedback

ð

No

Yes

Default: Yes

Tilt Feedback

ð

No

Yes

Default: Yes

ð

Screen

ð

Back Light

ð

On

10s

20s

30s

Default: 10s

Flip Display

ð

No

Yes

Auto

Default: No

DMX Led

ð

Off

On

Default:Off

Warn Cue

ð

Off

On

Default:On

Key Lock

ð

No

Yes

Default: No

ð

Fixture

ð

Full On Mode

ð

HB

Studio

Default:

Studio

ð

White Balance

ð

Oﬀ

Manual

ð

Red

Green

Blue

Warm

White

ð

125-255

ð

Calibrated Default: Activeted

9

PIXIEWASHXB

ð

Dimmer Mode

ð

Oﬀ

Dimmer 1

Dimmer 2

Dimmer 3

Default: Off

ð

Dimmer selection

ð

Option 1

Option 2

Option 3

Default: Option 2

ð

LED Frequency

ð

600Hz

1000Hz

2000Hz

4000Hz

8000Hz

25KHz

Default: 2000Hz

ð

Fan Mode

ð

Auto

Silent

High

Off

Default: Auto

ð

Temperature unit

ð

°C

°F

Default: °C

ð

Auto Test

ð

Auto Test …

ð

Manual Test

ð

Pan

Pan Fine

Tilt

Tilt Fine

P/T Speed

Dimmer

Shutter

Red

Green

Blue

White

Zoom

ð

000-255 Default:

Tilt=128

Dimmer=255

Shutter = 255

3 ADVANCED

ð

Reset

ð

All

Pan

Tilt

Zoom

ð

Adjust

ð

Pan Oﬀset

Tilt Oﬀset

Zoom Oﬀset

ð

000-255

ð

Factory Reload

ð

No

Yes

4 INFORMATION

ð

Fixture Time

ð

0-9999 Default: 0

Temperature

ð

58 °C

Fans Speed

ð

**%

Software Version

ð

DISP- V1.0

NET-V1.0

CTR1-XY- V1.0

CTR2-MOTOR-V1.0

UID

ð

15D00225****

View DMX

PIXIEWASHXB

10

3.4 DMX ADDRESSING

To set DMX addressing follow the instructions below:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Connect item. Press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the DMX Address item. Then press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the desired value 001-512; then press the button RIGHT to conﬁrm.

• Press repeatedly the button LEFT to return the menu mode.

To able to operate the PIXIEWASHXB with a light controller, adjust the DMX start address for the ﬁrst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the ﬁrst DMX

channel, adjust the start address 33 on the PIXIEWASHXB. The other functions of the light eﬀect panel are

then automatically assigned to the following addresses.

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

13 33 33-45 46 59 72

15 33 33-48 49 63 78

16 33 33-48 49 65 81

18 33 33-50 51 69 89

22 33 33-54 55 77 99

23 33 33-55 56 79 102

27 33 33-59 60 87 114

Fig.5 - Example 15 DMX channels configuration

. . . . . . . . . . . .

DMX512 Controller

DMX Address: 73DMX Address: 48DMX Address: 33 DMX Address: 63

Several units may be interconnected; follow the instructions below:

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the ﬁrst slave unit.

2. Connect the DMX OUT of the ﬁrst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last ﬁxture (see page 16).

11

PIXIEWASHXB

3.5 DMX CONFIGURATION

The PIXIEWASHXB has 6 DMX channels conﬁgurations selectable through the control panel.

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Connect. Press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the DMX mode. Then press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the desired conﬁguration (STANDARD-13CH, STANDARD-15CH, STAND-

ARD-16CH, EXTENDED-18CH, EXTENDED-22CH, EXTENDED-23CH, 27CH) then press the button RIGHT to save.

• Press repeatedly the button LEFT to return the menu mode.

The tables on page 15, 16, 17, 18, 19, 20 indicate the operating mode and DMX value. The PIXIEWASHXB is

equipped with 5-pole XLR connections.

3.6 WIRELESS SETTINGS

• To enter the Wireless mode press the LEFT button until the display shows Connect, then select Wireless

using the RIGHT button.

• Select the Wireless Receive function using the UP/DOWN buttons, then press the RIGHT button.

• To activate the Wireless Receive function, use the UP/DOWN buttons and select the On option.

• Press the RIGHT button to conﬁrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you

want to communicate by pressing the sync button on it. At this point connect the DMX console to the

WiFi unit to open the communication with the PIXIEWASHXB.

• To reset the unit, select the Receive Reset function using the UP/DOWN buttons, press the RIGHT button

until the display shows Connect, then select Receive Reset using the UP/DOWN buttons, then press the

RIGHT button.

• To activate the mode use the UP / DOWN keys and select the Yes option.

• Press the RIGHT button to conﬁrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

• To activate the Wireless to DMX function, use the UP / DOWN buttons to press the RIGHT button until the

display shows Connect, then select Wireless to DMX, then press the RIGHT button.

• To activate the mode use the UP/DOWN buttons and select the Yes option.

• Press the RIGHT button to conﬁrm the selection.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

3.7 ETHERNET

For the ArtNet settings to be assigned to the unit, refer to the following menu section.

• Press the UP/DOWN button to scroll through the menu, select Connect, then press the RIGHT button ac-

cess the next Ethernet menu with the UP / DOWN button, then press the RIGHT button.

• Use the UP/DOWN buttons to select one of the following settings: Universe, Start Channel, IP Address, Eth-

ernet to DMX.

• Press the RIGHT button to conﬁrm the selection and enter the sub menu.

• To activate the Ethernet to DMX function, use the UP / DOWN buttons to press the RIGHT button until the

display shows Connect, then select Ethernet to DMX, then press the RIGHT button.

• To activate the mode use the UP/DOWN buttons and select the Yes option.

• Press the RIGHT button to conﬁrm the selection.

• Set the desired value for the selected function using the UP/DOWN buttons. Then press the RIGHT

button.

• Press the LEFT button to go back or wait a few seconds to exit the setup menu.

PIXIEWASHXB

12

3.8 MOVEMENT

Press the LEFT button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the RIGHT button ac-

cess the next menu.

• Press the UP/DOWN button to select Movement and press the RIGHT button to proceed.

• Select the proposed option with the UP/DOWN button and press the RIGHT button to conﬁrm.

- Pan Reverse - Rotation in the opposite direction of the moving head. No to deactivate the function

(normal setting); Yes to activate the function (Pan Reverse).

- Tilt Reverse - Inclination in the opposite direction of the moving head. No to deactivate the function

(normal setting), Yes to activate the function (Tilt Reverse).

- Pan Reverse - Zoom in the opposite direction of the moving head. No to deactivate the function (nor-

mal setting); Yes to activate the function (Zoom Reverse).

- Pan/Tilt Feedbacks - Rearrange Pan/Tilt position after accidental shift. Select No for deactivate the func-

tion or Yes to activate the function.

• Press the RIGHT button to conﬁrm the selection.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

3.9 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the LEFT button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the RIGHT button ac-

cess the next menu.

• Press the UP/DOWN button to select Screen and press the RIGHT button to proceed.

• Select the proposed option with the UP/DOWN button and press the RIGHT button to conﬁrm.

- Backlight - Auto Oﬀ display backlight. This function allows you to switch oﬀ automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn oﬀ the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it or Auto.

- Warn Cue - Warning of error. Use the arrow keys to select Oﬀ or On depending on whether or not the

display shows error warnings.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, RIGHT. Select Yes to activate the function or

No to deactivate it.

• Press the RIGHT button to conﬁrm the selection.

• Press the LEFT key repeatedly to exit the menu and to save the changes made.

3.10 FIXTURE SETTINGS

You can change the parameters for the device by following these steps:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the System setup. Press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the desired option and press the button RIGHT to conﬁrm:

- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the

maximum value of the colors) or Studio mode with an automatic white calibration at 6000 K. Through

13

PIXIEWASHXB

the Studio mode it is possible to use separately the 4 single colors, only when all the colors are full

you will get the color temperature of 6000 K.

- White Balance - White Balance function. Select the White Balance function to set the white balance by

changing the values (125-255) of the colors Red, Green, Blue and White.

- Calibrated - With this function active, when the RGB colors are full, you will get 6000 K. In the same

way, using only the Warm White channel, you will still get 6000 K. So this mean that with this func-

tion activated white of PIXIEWASHXB is not warm white but a standard cold white at 6000K.

NOTE: to obtain 3000 K using the Warm White color, you must necessarily disable the Calibrated function

and activate the Studio function.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specific dimming curve.

Particularly when set:

• Off: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- Dimmer selection - Its function is to change the behavior of the Dimmer. Select the desired option

(Option 1 / Option 2 / Option 3).

- Fan Mode - Fan speed. Select the desired fan speed (Off, Auto, Silent, High) through the button UP/

DOWN.

- Temperature unit. Select Temperature unit function and then choose Celsius / Fahrenheit measurement unit

then press the RIGHT button to conﬁrm the selection.

• Press repeatedly the button LEFT to return the menu mode.

3.11 AUTO TEST

Allow checking the proper functioning of the unit. Start the automatic test in the following way:

• Press the button LEFT to enter the menu mode.

• Use the buttons UP/DOWN to select the Fixture. Press the button RIGHT to conﬁrm.

• Press the buttons UP/DOWN to select the Auto Test and press RIGHT to conﬁrm.

• To conﬁrm and start the automatic test press the RIGHT button.

3.12 MANUAL TEST

It allows to do adjustments on the eﬀects through commands panel to obtain a perfect balance between

the projectors.

• Press the button LEFT to enter the menu mode.

• Press the buttons UP/DOWN to select the item Fixture. Then press the button RIGHT.

• Press the buttons UP/DOWN to select the Manual Test. Then press the button RIGHT.

• Select the eﬀect you want change (Pan, Pan Fine, Tilt, Tilt Fine, P/T Speed, Dimmer, Shutter, Red, Green, Blue, White,

Zoom).Then press the button RIGHT to conﬁrm.

• Use the directional buttons to calibrate the eﬀect setting a value between 0 - 255. Then press the button

RIGHT to conﬁrm.

• Press repeatedly the button LEFT to return the menu mode.

3.13 ADVANCED

It is possible to modify the following parameters following the same procedure:

• Press the LEFT button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select Advanced, then press the RIGHT button

to enter the next menu.

PIXIEWASHXB

14

• Press the UP/DOWN button to select one off the following parametres:

- Reset - To start a preset program to restore the selected function (All, Pan, Tilt, Zoom).

- Adjust - To allows you to change all parameters. To access this mode, enter the password "050".Select

the desired function (Pan Oﬀset, Tilt Oﬀset, Zoom Oﬀset) and the choose the value (0 - 255).

- Factory Reload - To reset the unit. Select Yes or No and select RIGHT to confirm.

• Press the RIGHT button to confirm the selection and wait for the selected function to be restored.

• Press the LEFT button repeatedly to exit the menu and to save the changes made.

3.14 INFORMATION ON THE DEVICE

To view all the information on the device, proceed as follows:

• Press the LEFT button to access the main menu. Press the UP/DOWN button to select Information, then

press the RIGHT button to access the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information-

and press the RIGHT button to display it.- Fixture Time - Through the Fixture Time function, the operat-

ing time of the projector can be shown on the display.

- Fixture Time - To view the operating time of the projector.

- Temperature - To view the temperature of the device in °C on the display.

- Fans Speed - to view on the display the fan speed present near the lamp.

- Software Version - To view the firmware version will show on the display.

- UID - To view the identiﬁcation ID for the RDM control.

3.15 DMX VIEW

Select the View DMX function to display the DMX values received by the ﬁxture for each channel during

its operation.

15

PIXIEWASHXB

MODE MODE MODE MODE MODE MODE

FUNCTION DMX

Value

13 Ch 15 Ch 16 Ch 18 Ch 22 Ch 23 Ch

1 1 1 1 1 1

PAN COARSE

0~100% 000 - 255

2 2 2 2 2 2

PAN FINE

0~100% 000 - 255

3 3 3 3 3 3

TILT COARSE

0~100% 000 - 255

4 4 4 4 4 4

TILT FINE

0~100% 000 - 255

5 5 5 5 5 5

PAN/TILT SPEED

Fastest to slow

Movement with Blackout

000 - 250

251 - 255

6 6

SPECIAL FUNCTION

No function

Pan &Tilt Reset (Hold 3 Second)

No function

Zoom Reset (Hold 3 Second)

No function

000-049

050-099

100-149

150-199

200-255

6 6 6 6

SHUTTER

No function (shutter open)

Shutter effect slow to fast

No function (shutter open)

Pulse-effect in sequences

No function (shutter open)

Random Shutter effect slow to fast

No function (shutter open)

000 - 010

011 - 082

083 - 093

094 - 163

164 - 174

175 - 244

245 - 255

7 7 7 7 7 7

DIMMER 8bit

0~100% 000 - 255

8 8 8

DIMMER 16bit

0~100% 000 - 255

16 9 9 9

DIMMER FADE

0~100% 000 - 255

8 8

SHUTTER

Shutter closed

No function (Shutter open)

Shutter effect slow to fast

No function (Shutter open)

Pulse-effect in sequences

No function (Shutter open)

Random Shutter effect slow to fast

No function (Shutter open)

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

3.16 DMX CHANNELS

PIXIEWASHXB

16

MODE MODE MODE MODE MODE MODE

FUNCTION DMX

Value

13 Ch 15 Ch 16 Ch 18 Ch 22 Ch 23 Ch

8 10 10 10

CONTROL

No Function

CTC

CTC+Amber Shift

Forward Spin

Reverse Spin

Continuous

TBD

000 - 015

016 - 023

024 - 031

032 - 047

048 - 063

064 - 079

080 - 255

13

COLOR FUNCTION

No Function

CTC Function

Forward Spin

Reverse Spin

Continuous

TBD

000 - 019

020 - 039

040 - 059

060 - 079

080 - 099

100 - 255

14

COLOR

Color Temperature Correction 2000K -->3000K

White 3200 K

White 4200 K

White 5600 K

White 8000 K

FORWARD SPIN

Rainbow Effect (Slow to Fast)

REVERSE SPIN

Rainbow Effect (Slow to Fast)

CONTINUOS

Black

Red

Green

Blue

White

Red=0; Green ->Up; Blue=Full; White=0

Red=0; Green =Full; Blue->Down; White=0

Red->Up; Green=Full; Blue=0; White=0

Red=Full; Green ->Down; Blue=0; White=0

Red=Full; Green=0; Blue->Up; White=0

Red->Down; Green=0; Blue=Full; White=0

000 - 223

224 - 231

232 - 239

240 - 247

248 - 255

000 - 255

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

17

PIXIEWASHXB

MODE MODE MODE MODE MODE MODE

FUNCTION DMX

Value

13 Ch 15 Ch 16 Ch 18 Ch 22 Ch 23 Ch

9 11 11 11

CTC or CTC+AMBER SHIFT

2800K

3000K

3200K

3400K

3600K

3800K

4000K

4200K

4400K

4600K

4800K

5000K

5200K

5400K

5600K

5800K

6000K

6200K

6400K

6600K

6800K

7000K

7200K

7400K

7600K

7800K

8000K

000 - 000

001 - 010

011 - 020

021 - 030

031 - 040

041 - 050

051 - 060

061 - 070

071 - 080

081 - 090

091 - 100

101 - 110

111 - 120

121 - 130

131 - 140

141 - 150

151 - 160

161 - 170

171 - 180

181 - 190

191 - 200

201 - 210

211 - 220

221 - 230

231 - 240

241 - 250

251 - 255

COLOR(FW spin)

Rainbow Effect (Slow to Fast) 000 - 255

COLOR(RW spin)

Rainbow Effect (Slow to Fast) 000 - 255

COLOR (Continuous)

Black

Red

Green

Blue

Warm White

Red=0, Green->up, Blue=full, Warm White=0

Red=0, Green=full, Blue->down, Warm White=0

Red->up, Green=full, Blue=0, Warm White=0

Red=full, Green->down, Blue=0, Warm White=0

Red=full, Green=0, Blue->up, Warm White=0

Red->down, Green=0, Blue=full, Warm White=0

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

12

HUE

0

-25~25

000 - 000

001 - 255

PIXIEWASHXB

18

MODE MODE MODE MODE MODE MODE

FUNCTION DMX

Value

13 Ch 15 Ch 16 Ch 18 Ch 22 Ch 23 Ch

9 10 9 12 12 13

RED

0~100%

000 - 255

13 14

RED FINE

0~100%

000 - 255

10 11 10 13 14 15

GREEN

0~100%

000 - 255

15 16

GREEN FINE

0~100%

000 - 255

11 12 11 14 16 17

BLUE

0~100%

000 - 255

17 18

BLUE FINE

0~100%

000 - 255

12 13 12 15 18 19

WARM WHITE

0~100%

000 - 255

19 20

WARM WHITE FINE

0~100%

000 - 255

13 14 15 16 20 21

ZOOM

0~100%

000 - 255

17 21 22

ZOOM FINE

0~100%

000 - 255

15 18 22 23

CONTROL

No function

Reset all

Pan&Tilt Reset

TBD

Zoom Reset

TBD(not used)

Fast Mode

TBD(not used)

000 - 007

008 - 015

016 - 023

044 - 047

048 - 055

056 - 063

064 - 071

072 - 255

La pagina sta caricando ...

ProLights PIXIEWASHXB Manuale utente

ProLights PIXIEWASHXB Manuale utente

in altre lingue

Documenti correlati