Philips GC6103 Manuale del proprietario

GC6107, GC6106, GC6104, GC6103, GC6102, GC6101

2

3

1

4

GC6107, GC6106, GC6104, GC6103, GC6102, GC6101

ENGLISH 6

DANSK 15

DEUTSCH 24

 33

ESPAÑOL 43

SUOMI 52

FRANÇAIS 60

ITALIANO

69

NEDERLANDS

78

NORSK

87

PORTUGUÊS

96

SVENSKA

105

TÜRKÇE 114

6

General description (Fig. 1)

A Supply hose

B Temperature light

C Temperature dial and indicator

D Steam activator and lock

D1 Lock

D2 Activator

E Cap of steam tank

F Iron stand

G Steam tank

H Mains cord

I Steam-ready light (GC6107 only)

J Steam tank switch with power-on light

K Steam control (GC6107/GC6104 only)

L Iron switch with power-on light

M ’Steam tank empty’ light (GC6107 only)

N Soleplate

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Danger

Never immerse the iron or the steam tank in water.

Warning

Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

Do not use the appliance if the plug, the mains cord, the supply hose or

the appliance itself shows visible damage, or if the appliance has been

dropped or leaks.

If the mains cord or the supply hose is damaged, you must have it

replaced by Philips, a service centre authorised by Philips or similarly

qualied persons in order to avoid a hazard.

Never leave the appliance unattended when it is connected to the

mains.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the

appliance.

Do not let the mains cord and supply hose come into contact with the

hot soleplate of the iron.

If steam escapes from under the steam tank cap when the appliance

heats up, switch off the appliance and tighten the steam tank cap. If

steam continues to escape when the appliance is heating up, switch

off the appliance and contact a service centre authorised by Philips.

Do not remove the steam tank cap from the steam tank when the

steam tank is still under pressure.

-

ENGLISH

Do not use any other cap on the steam tank than the cap that has

been supplied with the appliance, as the steam tank cap also functions

as a safety valve.

Caution

Only connect the appliance to an earthed wall socket.

Check the mains cord and the supply hose regularly for possible

damage.

Always place and use the iron and the steam tank on a stable, level and

horizontal surface. Do not put the steam tank on the soft part of the

ironing board.

The iron stand and the soleplate of the iron can become extremely

hot and may cause burns if touched. If you want to move the steam

tank, do not touch the stand.

When you have nished ironing, when you clean the appliance, when

you ll or empty the steam tank and also when you leave the iron even

for a short while: put the iron on the iron stand, set the iron switch and

the steam tank switch to ‘off ’ and remove the mains plug from the wall

socket.

Rinse the steam tank regularly according to the instructions in the

chapter ‘Cleaning and maintenance’.

This appliance is intended for household use only.



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.



1

Remove any sticker or protective foil from the soleplate and clean

the soleplate with a soft cloth.

2 Fully unwind the mains cord and supply hose.

3 Place the steam tank on a stable, level surface.

4 Place the iron on the iron stand.

Preparing for use

Filling the steam tank

Never immerse the steam tank in water.

Do not open the cap when the iron and the steam tank are still hot.

1 Remove the mains plug from the wall socket.

-

ENGLISH 7

2 Slowly unscrew the cap of the steam tank.

You may hear a sound when you remove the cap. This sound is caused by

the vacuum or residual pressure inside the steam tank and is perfectly

normal.

3 Pour water into the steam tank (max. 1 litre).

Use tap water to ll the tank.

If the tap water in your area is very hard, we advise you to use 50%

distilled water and 50% tap water.

Do not put perfume, vinegar, starch, descaling agents, ironing aids or

other chemicals in the steam tank.

4 Screwthecaptightlyontothellingapertureofthesteamtank.



1 Keep the appliance plugged into the mains and make sure the iron is

on. Then set the steam tank switch to ‘off’.

2 Press the steam activator until you no longer hear any steam

escaping from the appliance.

3 Keep the steam activator pressed in and slowly unscrew the cap of

the steam tank by turning it anticlockwise. This will depressurise the

steam tank.

Make sure there is no steam left in the steam tank. Place a piece of cloth

over the cap when unscrewing it.

4 Remove the mains plug from the wall socket.

5 Fill the steam tank as described in section ‘Filling the steam tank’ and

let the appliance heat up again.

Setting the temperature

Always place the steam tank on a stable, level and horizontal surface. Do

not put the steam tank on the soft part of the ironing board.

1 Put the iron on the iron stand.

Do not put the hot iron on the supply hose or the mains cord. Make

sure the cord does not come into contact with the hot soleplate.

,

ENGLISH8

2 Set the required ironing temperature by turning the temperature dial

to the appropriate position.

Check the laundry care label for the required ironing temperature:

Symbol on laundry

care label

Type of fabric Temperature

setting

Steam setting

B Synthetic fabrics (e.g. acetate, acrylic,

viscose, polyamide, polyester) and silk

1 MIN (see ‘Ironing

without steam’)

C Wool 2 Low to medium

D Cotton, linen 3 Medium to MAX

Z Please note that Z on the label

means that the article cannot be

ironed.

- -

If you do not know what kind(s) of fabric(s) an article is made of,

determine the right ironing temperature by ironing a part that will not be

visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to

prevent shiny patches.

Start ironing the articles that require the lowest ironing temperature, such

as those made of synthetic bres.

3 Put the mains plug in an earthed wall socket and set both the steam

tank switch and the iron switch to ‘on’. The steam tank and the

soleplate will now heat up.

The iron is hot enough when the temperature light goes out.

During steam ironing the temperature light goes on from time

to time. This indicates that the iron is heating up to the right

temperature.

If you have been ironing at a high temperature and subsequently set

the temperature dial to a lower setting, wait until the temperature

light goes on again before you continue ironing. This will prevent

damage to your fabrics.

Tips

If the fabric consists of various kinds of bres, always select the

temperature required by the most delicate bre, i.e. the lowest

temperature. For example: if an article consists of 60% polyester and

40% cotton, it should be ironed at the temperature indicated for

polyester ( 1) and without steam.

When steam ironing woollen fabrics, shiny patches may occur. You

can prevent this by using a dry pressing cloth or by turning the article

inside out and ironing the reverse side.

,

-

ENGLISH 9

Velvet and other fabrics that tend to acquire shiny patches should be

ironed in one direction only (along with the nap) while applying very

little pressure.

Do not use steam when you are ironing coloured silk. This could cause

stains.

Using the appliance

Steam ironing

1 Make sure that there is enough water in the steam tank.

Steam ironing is only possible at higher ironing temperatures

(temperature settings 2 to MAX).

2 Select a steam setting suitable for the selected ironing temperature:

Select steam setting MIN (no steam) for temperature setting 1 (see

‘Ironing without steam’).

Select a low to medium steam setting for temperature setting 2.

Select a medium to MAX steam setting for temperature settings 3

to MAX.

3 The steam tank and the soleplate will now heat up.

Cold start: the soleplate takes approximately 2 minutes to heat up and

the steam tank takes approximately 8 minutes to heat up.

Quick reheat: if you rell the steam tank during the ironing process, the

water in the steam tank will take approximately 6 minutes to heat up.

4 As soon as the water in the steam tank is hot enough for steam

ironing, the steam tank power-on light goes out (GC6106, GC6104,

GC6103, GC6102 only). The steam-ready light goes on (GC6107

only).

During steam ironing the steam-ready light goes on from time to

time. This indicates that the steam tank is being heated up to the

right temperature.

5 Keep the steam activator pressed in while you are steam ironing.

If you want to use the steam function continuously, slide the steam

activator lock to the locking position.

6 To stop steaming, release the steam activator lock.

If you have not used the steam function for some time, the steam that was

still present in the supply hose will have condensed into water. When you

start steam ironing again, this may cause some spluttering in the appliance

and a few droplets of water may escape from the soleplate.

Note: To prevent droplets from falling onto your garments, hold the iron over

an old cloth and press the steam activator until the steam production has

normalised before you start steam ironing again.

Ironing without steam

1 Select the recommended ironing temperature (see chapter ‘Preparing

for use’).

Do not press the steam activator while ironing.

-

,

-

,

ENGLISH10

Some steam will escape if you press the steam activator by accident

while you are ironing. To avoid this, you can simply set the steam tank

switch to ‘off’ to cut off the steam supply completely.

If the steam tank is empty or has not heated up yet, you will hear

a clicking sound inside the tank. This phenomenon is caused by the

opening of the steam valve and is perfectly harmless.

Features

Vertical steam ironing

Hanging curtains and clothes (jackets, suits, coats) can be steam

ironed by holding the iron in vertical position.

1 Press the steam activator. If you want to use the steam function

continuously, use the steam activator lock.

Never direct the steam at people.

Variable steam (GC6107 and GC6104 only)

The steam control is continuously adjustable and can be set to any position

between MIN and MAX (see chapter ‘Preparing for use’).

’Steam tank empty’ light (GC6107 only)

When the water in the steam tank runs out during use, the ‘steam tank

empty’ light goes on.

1 Rellthesteamtankwithwater(seechapter‘Preparingforuse’).

Steam-ready light (GC6107 only)

When the steam tank is ready for steam ironing, the steam-ready light goes

on.

Cleaning and maintenance

After ironing

1 To depressurise the steam tank, set the iron switch to ‘on’ and the

steam tank switch to ‘off’.

,

ENGLISH 11

2 Depressurise the steam tank by pressing the steam activator until

you no longer hear any steam escaping from the appliance.

3 Remove the mains plug from the wall socket.

4 Put the iron on the iron stand, set the steam control to MIN and let

the appliance cool down before you start cleaning it.

Iron

1 Clean the iron with a damp cloth.

2 Wipe scale and any other deposits off the soleplate with a damp

cloth and a non-abrasive (liquid) cleaner.

Never immerse the iron in water nor rinse it under the tap.

Steam tank

Rinse the steam tank once a month or after you have used the appliance

approximately 10 times.

1 Carefully remove the cap of the steam tank.

Lettheappliancecooldownsufcientlybeforeremovingthecap.

2 Rinse the steam tank with 500 ml of fresh water. Pour out the water

by holding the steam tank upside down over the sink.

3 Screw the cap back onto the steam tank.

Storage

Makesuretheironhascooleddownsufcientlybeforeyouputitaway.

1 Remove the mains plug from the wall socket and let the iron cool

down.

2 Empty the steam tank.

3 Regularly check if the mains cord and the supply hose are still

undamaged and safe.

Environment

Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.

-

ENGLISH12

Guarantee & service

If you need information or if you have a problem, please visit the Philips

website at www.philips.com or contact the Philips Customer Care Centre

in your country (you nd its phone number in the worldwide guarantee

leaet). If there is no Customer Care Centre in your country, go to your

local Philips dealer or contact the Service Department of Philips Domestic

Appliances and Personal Care BV.

Troubleshooting

This chapter summarises the most common problems you could encounter

with your iron. Please read the different sections for more details. If you

are unable to solve the problem, please contact the Philips Customer Care

Centre in your country (you will nd its phone number in the worldwide

guarantee leaet). If there is no Customer Care Centre in your country,

turn to your local Philips dealer or the nearest Philips service centre.

Problem Cause Solution

Some smoke comes

out of the appliance

after it has been

switched on for the

rst time.

This is normal. Some parts of the iron

have been greased lightly in the factory.

This phenomenon will cease after a

short while.

Dirt particles come

out of the soleplate

of the new iron.

This is normal with a new iron. These particles are harmless and they

will stop coming out of the soleplate

when you have used the iron a few

times.

Droplets of water

escape from the

soleplate.

The temperature dial has been set to a

temperature that is too low for steam

ironing.

Select an ironing temperature that is

suitable for steam ironing (temperature

settings 2 to MAX).

The iron is not switched on. Set the iron switch to ‘on’ and wait until

the iron is hot.

The steam tank has been placed on an

unstable and/or uneven surface.

Put the steam tank on a stable and even

surface.

When you start steam ironing, the

hose is cold. Steam condenses in the

hose, causing droplets of water to

escape from the soleplate.

This is normal. Hold the iron over an

old cloth and press the steam activator.

The cloth will absorb the drops. After a

few seconds the steam production will

have normalised.

The appliance does

not produce any

steam.

The steam tank and/or the iron has/

have not been switched on.

Set both the iron switch and the steam

tank switch to ‘on’.

The steam tank is not hot enough to

produce steam.

Wait 6 to 8 minutes for the steam tank

to heat up.

ENGLISH 13

Problem Cause Solution

There is no steam

coming out of the

soleplate.

Superheated (i.e. high-quality) steam

is hardly visible, especially when the

temperature dial has been set to

maximum position and even less so

when the ambient temperature is

relatively high.

To check if the iron is really producing

steam, hold a (cold) mirror in front of

the soleplate vents.

The soleplate is

dirty.

Impurities or chemicals present in the

water have deposited on the soleplate.

Clean the soleplate with a damp cloth.

You have been ironing at too high

temperatures.

Clean the soleplate with a damp cloth.

Select the recommended ironing

temperature.

Symbol on

laundry care

label

Type of fabric Temperature

setting

Steam setting

B Synthetic fabrics (e.g. acetate, acrylic,

viscose, polyamide, polyester) and

silk

1 MIN (see

‘Ironing

without

steam’)

C Wool 2 Low to

medium

D Cotton, linen 3 Medium to

MAX

Z Please note that Z on the label

means that the article cannot be

ironed.

ENGLISH14

15



A Dampslange

B Temperaturindikator med lys

C Temperaturvælger og indikator

D Dampaktiveringsknap med lås

D1 Lås

D2 Aktiveringsknap

E Låg til damptank

F Holder til strygejernet

G Damptank

H Netledning

I Lysindikator for damp klar (kun GC6107)

J Kontakt til damptank (lyser når tændt)

K Dampkontrol (kun GC6107/GC6104)

L Kontakt til strygejern (lyser når tændt)

M Lysindikator for tom damptank (kun GC6107)

N Strygesål

Vigtigt

Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i

brug, og gem den til eventuelt senere brug.

Fare

Hverken strygejern eller damptank må kommes ned i vand.

Advarsel

Kontrollér, om spændingsangivelsen på typeskiltet svarer til den lokale

netspænding, før du tilslutter apparatet.

Brug ikke apparatet, hvis stik, netledning, dampslange eller selve

apparatet viser tegn på beskadigelse, eller hvis apparatet er blevet tabt,

eller det er utæt.

Hvis ledningen eller dampslangen beskadiges, må de kun udskiftes af

Philips, et autoriseret Philips-serviceværksted eller af en kvaliceret

fagmand for at undgå enhver risiko ved efterfølgende brug.

Hold altid apparatet under opsyn, når det er sluttet til lysnettet.

Dette apparat er ikke beregnet til at blive brugt af personer (herunder

børn) med nedsatte fysiske og mentale evner, nedsat følesans eller

manglende erfaring og viden, medmindre de er blevet vejledt eller

instrueret i apparatets anvendelse af en person, der er ansvarlig for

deres sikkerhed.

Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke

kan komme til at lege med det.

Lad ikke netledningen og dampslangen komme i kontakt med den

varme strygesål på strygejernet.

Hvis der slipper damp ud under låget til damptanken, mens

apparatet varmer op, skal du slukke for apparatet og stramme låget

til damptanken. Slipper der fortsat damp ud, mens apparatet varmer

op, skal du slukke for apparatet og kontakte din Philips-forhandler for

eventuelt eftersyn/reparation.

Tag aldrig låget af damptanken, mens damptanken er under tryk.

Brug kun det medfølgende låg til damptanken, da det samtidig fungerer

som sikkerhedsventil.

-

DANSK

Forsigtig

Apparatet må kun sluttes til en stikkontakt med jordforbindelse.

Kontrollér med jævne mellemrum, at netledningen og dampslangen er

hel og ubeskadiget.

Placér og brug altid strygejern og damptank på et stabilt, plant og

vandret underlag. Damptanken må ikke stilles på den bløde del af

strygebrættet.

Strygejernets holder og strygesål kan blive meget varme og forårsage

brandsår ved berøring. Undgå berøring af holderen, hvis damptanken

yttes.

Når du er færdig med at stryge, når du rengør apparatet, når du

fylder eller tømmer damptanken, og når du forlader strygejernet

– selv om det kun er i et kort øjeblik – skal du placere strygejernet i

standeren, slukke for strygejernet og damptanken og tage stikket ud af

stikkontakten.

Rengør damptanken regelmæssigt ifølge anvisningerne i afsnittet

‘Rengøring og vedligeholdelse’.

Dette apparat er kun beregnet til almindelig husholdningsbrug.

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle standarder for elektromagnetiske

felter (EMF). Ved korrekt anvendelse i overensstemmelse med

instruktionerne i denne brugsvejleding, er apparatet sikkert at anvende,

ifølge den videnskabelige viden, der er tilgængelig i dag.

Før apparatet tages i brug første gang

1

Fjerneventuellemærkaterellerbeskyttelseslmfrastrygesålen,og

rengør den med en blød klud.

2 Rul netledningen og dampslangen helt ud.

3 Anbringdamptankenpåetstabiltogplantunderlag.

4 Sæt strygejernet i standeren.

Klargøring

Fyldning af damptanken

Damptankenmåaldrigkommesnedivand.

Tagikkelågetaf,sålængestrygejernogdamptankervarme.

1 Tag stikket ud af stikkontakten.

2 Skruforsigtigtlågetafdamptanken.

Derkanforekommeenlyd,nårdufjernerlåget.Lydenskyldesdet

vakuum eller resttryk, der er i damptanken, og er helt normal.

-

DANSK16

3 Hæld vand i damptanken (max. 1 liter).

Brug vand fra vandhanen.

Hvisvandetiditlokalområdeermegethårdt,anbefalesdetatbruge

50 % destilleret vand og 50 % postevand.

Hæld ikke parfume, eddike, stivelse, afkalkningsmiddel, strygemidler eller

andre kemikalier i damptanken.

4 Skrulågetgodtfastpådamptankenspåfyldningsåbning.

Hurtig påfyldning

1 Lad apparatet være tilsluttet stikkontakten, og kontrollér, at

strygejernetertændt.Sætderefterkontaktentildamptankenpå

“off”.

2 Trykpådampaktiveringsknappen,indtilduikkelængerekanhøre,at

der slipper damp ud fra apparatet.

3 Hold dampaktiveringsknappen nedtrykket, og skru samtidig forsigtigt

lågettildamptankenafvedatdrejedetmoduretsretning.Påden

mådetagestrykketafdamptanken.

Sørg for, at der ikke er mere damp tilbage i damptanken. Læg en klud hen

over låget, mens du skruer det af.

4 Tag stikket ud af stikkontakten.

5 Fylddamptankensombeskrevetiafsnittet“Påfyldningaf

damptanken”, og lad apparatet varme op igen.

Temperaturindstilling

Placéraltiddamptankenpåetstabilt,plantogvandretunderlag.

Damptankenmåikkestillespåselvestrygebrættet.

1 Stil strygejernet i holderen.

Stilikkedetvarmestrygejernovenpådampslangenellernetledningen.

Sørg for, at netledningen ikke kommer i kontakt med den varme

strygesål.

,

DANSK 17

2 Indstil den ønskede strygetemperatur ved at dreje

temperaturvælgeren.

Kontrollér tøjets vaskemærke, og nd den rette strygetemperatur.

Symbolpåtøjets

vaskemærke

Stoftype Temperaturindstilling Dampindstilling

B Kunststoffer (f.eks. acetat, acryl,

viskose, polyamid, polyester) og silke

1 MIN (se afsnittet

“Tørstrygning (uden

damp)”)

C Uld 2 Lav til medium

D Bomuld, hør, linned 3 Medium til MAX

Z Bemærk, at Z-symbolet på

vaskemærket betyder, at det

pågældende stykke tøj ikke tåler

strygning.

- -

Ved du ikke, hvilken type materiale der er tale om, må du prøve dig

forsigtigt frem et sted på tøjet, der ikke ses under brug.

Silke, uld eller kunststof: Stryg tøjet på vrangen for at undgå blanke skjolder.

Begynd med at stryge det tøj, som kræver den laveste temperatur, dvs. det,

som er fremstillet af kunststof.

3 Sæt netledningens stik i en stikkontakt med jordforbindelse, og sæt

kontakternetildamptankogstrygejernpå“on”.Damptankenog

strygesålenvarmernuop.

Nårtemperaturindikatorenslukker,harstrygejernetdenrette

temperatur.

Under dampstrygning tænder temperaturindikatoren med jævne

mellemrum. Dette indikerer, at strygejernet varmer op til den valgte

temperatur.

Hvis du har strøget ved høj temperatur og derefter indstiller

temperaturvælgeren til en lavere temperatur, skal du vente, indtil

temperaturindikatoren tænder igen, før du fortsætter med at stryge.

Såundgårduatbeskadestoffet.

Gode råd

Hvis stoffet er fremstillet af ere slags bre, skal du altid vælge den

temperatur, som passer til den sarteste bertype, dvs. den laveste

temperatur. Hvis et stykke tøj f.eks. består af 60 % polyester og 40 %

bomuld, bør det stryges ved den temperatur, som passer til polyester (

1), og uden damp.

,

-

DANSK18

Ved dampstrygning af uld kan du risikere, at der kommer blanke

skjolder. Dette undgås ved enten at lægge et strygestykke over eller

stryge tøjet på vrangen.

Fløjl og andre stoffer, som har tendens til at få blanke skjolder, bør kun

stryges i én retning (med luven) og kun med et let tryk.

Undlad at bruge damp ved strygning af indfarvede silkestoffer, da det

kan give skjolder på tøjet.

Sådan bruges apparatet

Dampstrygning

1 Sørg for, at der er nok vand i damptanken.

Dampstrygning er kun mulig ved høje strygetemperaturer

(temperaturindstilling 2 til MAX).

2 Vælg den dampindstilling, som passer til den valgte strygetemperatur:

Vælg dampindstilling MIN (ingen damp) til temperaturindstilling 1 (se

afsnittet “Tørstrygning (uden damp)”).

Vælg lav til medium dampindstilling til temperaturindstillingen 2.

Vælg medium til MAX dampindstilling til temperaturindstillinger 3

til MAX.

3 Damptankenogstrygesålenvarmernuop.

Koldstart: Det tager ca. 2 minutter at varme strygesålen op, og ca. 8

minutter at opvarme damptanken.

Hurtig genopvarmning: Hvis du fylder vand på damptanken i løbet af en

strygeproces, tager det ca. 6 minutter at genopvarme damptanken.

4 Såsnartvandetidamptankenervarmtnoktildampstrygning,slukker

kontrollampen i kontakten til damptanken (kun GC6106, GC6104,

GC6103, GC6102). Lysindikatoren for damp klar tænder (kun

GC6107).

Under dampstrygning tænder kontrollampen for damp indimellem.

Dette indikerer, at damptanken opvarmes til den valgte temperatur.

5 Hold dampaktiveringsknappen nede under dampstrygning.

Hvisduvilbrugedampfunktionenkonstant,skubbeslåsentil

dampaktiveringsknappenilåseposition.

6 Skublåsentildampaktiveringsknappentilbageiåbenposition,nårdu

vil standse dampproduktionen.

Har du ikke brugt dampfunktionen i et stykke tid, er den resterende damp

i dampslangen fortættet til vand. Når du begynder at dampstryge igen, kan

det få strygejernet til at sprutte, og der kan dryppe et par vanddråber ud

igennem strygesålen.

Bemærk: For at undgå at der drypper vand på tøjet, holdes strygejernet

over en gammel klud og dampaktiveringsknappen holdes nede, indtil

dampproduktionen er blevet normal. Herefter kan dampstrygningen fortsættes.

Tørstrygning (uden damp)

1 Indstil den anbefalede strygetemperatur (se afsnittet “Klargøring”).

Undladattrykkepådampaktiveringsknappen,mensdustryger.

-

,

-

,

DANSK 19

Der vil slippe en smule damp ud, hvis du ved et uheld kommer til at

trykkepådampaktiveringsknappenunderstrygningen.Foratundgå

dette kan du afbryde dampproduktionen helt ved at sætte kontakten

tildamptankenpå“off”.

Hvis damptanken er tom eller endnu ikke er varmet op, vil du høre

enklikkendelydindefratanken.Detskyldes,atdampventilenåbnes,

og det er ganske harmløst.

Funktioner

Lodret dampstrygning

Gardinerogtøjpåbøjle(f.eks.jakker,habitter,frakker)dampesnemt

ved at holde strygejernet i lodret position.

1 Trykpådampaktiveringsknappen.Hvisduvilbrugedampfunktioneni

længeretidadgangen,skaldubrugelåseknappen.

Retaldrigdampstrålenmodpersoner.

Variabel damp (kun GC6107 og GC6104)

Dampvælgeren har trinløs regulering og kan indstilles til en hvilken som

helst position mellem MIN og MAX (se afsnittet “Klargøring”).

Lysindikator for tom damptank (kun GC6107)

Når damptanken løber tør for vand under strygningen, tænder

lysindikatoren for tom damptank.

1 Fyld mere vand i damptanken (se afsnittet “Klargøring”).

Lysindikator for damp klar (kun GC6107)

Når damptanken er klar til dampstrygning, tænder lysindikatoren for damp

klar.

Rengøring og vedligeholdelse

Efter brug

1 Trykkettagesafdamptankenvedatsættekontaktenpåstrygejernet

på“on”ogkontaktenpådamptankenpå“off”.

,

DANSK20

La pagina sta caricando ...

Philips GC6103 Manuale del proprietario

Questo manuale è adatto anche per

Philips GC6103 Manuale del proprietario

in altre lingue

Documenti correlati