Indesit ARMXXL 105 (EU) Guida utente

Marca: Indesit

Modello: ARMXXL 105 (EU)

Categoria: Lavatrici

Tipo: Guida utente

English,1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washer-dryer and

starting a wash cycle, 4-5

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

ARMXXL 105

Instructions for use

WASHER DRYER

Á ÚËÃÀÐÑÊÈ,25

BGRO

Românã,13

CIS

Ðóññêèé,37

ÅËËÇÍÉÊÁ,49

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washer-dryer needs to be moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washer-dryer.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose and

screw the latter onto a

cold water tap with a 3/4

gas threaded opening

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washer-dryer by

screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Technical data

Model

ARMXXL 105

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 7 kg for the wash programme;

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data plate

fixed to the machine

Wate r

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rotations per minute

Energy rated

programmes

according to

EN 50229

Wash: programme 6; temperature 60°C;

using a load of 7 kg.

Drying:

first drying cycle performed with a

2 kg load, by selecting the dryness level.

The second drying cycle is performed with a

5 kg load, by selecting the dryness level.

This appliance conforms to the following

EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washer-dryer. If this is not the case, replace the

socket or the plug.

 The washer-dryer must not be installed outdoors,

even in covered areas. It is extremely dangerous to

leave the appliance exposed to rain, storms and other

weather conditions.

 When the washer-dryer has been installed, the

electricity socket must be within easy reach.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 1.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

There is a key which provides a summary of the

available wash cycles inside the detergent dispenser

drawer; this may be consulted at any time.

ON/OFF button: switches the washer-dryer on and

off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

DRYING knob: used to set the desired drying

programme (see Personalisation).

WASH CYCLE PROGRESS/DELAY TIMER

indicator light

s: used to monitor the progress of the

wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time

remaining until the wash cycle starts will be indicated

(see next page).

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Description of the washer-dryer and

starting a wash cycle

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

DRYING

knob

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Control panel

WASH CYCLE

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see

Personalisation), after the wash cycle has been

started the indicator light corresponding to the

selected delay period will begin to flash:

As time passes, the remaining delay will be displayed

and the corresponding indicator light will flash:

Once the set delay has elapsed, the flashing indicator

light will switch off and the selected wash cycle will

begin.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Note: during the "Drain" phase, the indicator light

corresponding to the "Spin" cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If a function which is incompatible with another

function selected previously, only the most recent

selection will remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked

to prevent it from being opened accidentally; to avoid

any damage, wait for the indicator light to switch off

before you open the appliance door.

N.B. If the DELAY TIMER function is activated, the door

cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

 If the START/PAUSE indicator light (orange) flashes

rapidly at the same time as the function indicator

light, this indicates a problem has occurred (see

Troubleshooting).

Starting a wash cycle

1. Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the drying cycle if necessary (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE

button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The DOOR LOCKED indicator light will switch

off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make

sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

Note: as soon as a drying

level or time period has been

set, this indicator light

illuminates to indicate that

the selected wash cycle will

be followed by a drying

phase.

Specials wash cycles

Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach.

Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled

Detergent dispenser drawer).

Goodnigt cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower. The

wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in

the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin

cycle and drain the water automatically after 8 hours.

Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring

that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The

cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect

of special disinfecting additives added to the detergent.

At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle

press the START/PAUSE button.

Mix 30(wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and

therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics

together (except for wool and silk items), with a maximum load of 3 kg.

Mix 15(wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and

therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics

together (except for wool and silk items), with a maximum load of 1.5 kg.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 6 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

duration

Bleach Wash

Fabric

softener

Specials cycles

Sanitizing cycle:

Extremely soiled whites.

90° 1000

llll

7170

Sanitizing cycle (1):

Heavily soiled whites and resistant colours.

60° 1000

7 153

Goodnigt cycle:

Lightly soiled delicate colours.

40° 1000

4290

Baby cycle:

Heavily soiled delicate colours.

40° 800

2118

Silk/Curtains:

For garments in silk and viscose, lingerie.

30° 0 - -

155

Wool:

For wool, cashmere, etc.

40° 800

1,5 55

Daily wash cycles

Cotton:

Heavily soiled whites and resistant colours.

60° 1000

llll

7 122

Cotton (2):

Heavily soiled whites and delicate colours.

40° 1000

llll

7115

Coloured Cottons (3):

Lightly soiled whites and delicate colours.

40° 1000

llll

785

Synthetics resistents:

Heavily soiled resistant colours.

60° 800

385

Synthetics resistents:

Lightly soiled resistant colours.

40° 800

370

Mix 30':

To refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800

330

Mix 15':

To refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800

1,5 15

Partials wash cycles

Rinse - 1000

- -

736

Spin - 1000

- - - 716

Drain no spin - 0 - - - - 72

Drying cycles

Cotton drying - -

- - - 5 -

Synthetics drying - -

- - - 3 -

Wool drying - -

- - - 1,5 -

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash (

The washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum

value set for each wash cycle.

Setting the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they have

been dried:

Iron

: slightly damp clothes, easy to iron.

Hanger

: dry clothes to put away.

Cupboard

: very dry clothes, recommended for towelling

and bathrobes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table),

perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them

back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure

for the remainder of the load.

N.B: When the drying is complete there is a cooling period, even though the DRYING knob is in the

position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select

the desired drying duration using the DRYING knob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time

the button is pressed, the function will be disabled.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

 This option is enabled with all programmes.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is

particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 4, 5, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle

duration, this function offers a high-performance wash.

 This function may not be used in conjunction with wash cycles 4, 5, 6, 9, 10, 11, 12, 13, A, B, C.

1000-500

By selecting this function, reduces the spin speed.

 This function may not be used in conjunction with wash cycles 9, C, 11, 12, 13.

Personalisation

Fabric

type

Load type Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels

5 180 170 160

Synthe-

tics

Sheets, Shirts, Pyjamas,

socks, etc.

3 180 170 160

Wool Knitwear, Pullovers, etc.

1,5 150 140 130

Table of Drying times (guideline values)

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Bleach cycle

Bleaching may only be performed in conjunction with

wash cycles 1, 2, 6.

Pour the bleach into extra compartment 4; pour the

detergent and softener into the corresponding

compartments, then select one of the

abovementioned wash cycles.

This option is recommended only for very soiled

cotton garments.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1.5 kg

MAX

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Silk: use special wash cycle 9 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: these should be folded and placed inside

the bag provided. Use wash cycle 9.

Wool: Hotpoint/Ariston is the only washer-dryer

manufacturer to have been awarded the prestigious

Woolmark Platinum Care endorsement (M.0508) by

the Woolmark Company, which means that all

woollen garments may be washed in the washer-

dryer, even those which state hand wash only

on the label. Wash cycle 10 therefore offers complete

peace of mind when washing woollen garments in the

washer-dryer (max. load 1.5 kg) and guarantees

optimal performance.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washer-dryer

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Anti-crease

This function interrupts the wash programme, and the

washing is left to soak in water before the appliance

is drained.

It can only be used with programme 9 (Silk/Curtains)

and helps to prevent the formation of creases.

To complete the cycle press the START/PAUSE

button.

Precautions and tips

 This washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons

and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The washer-dryer must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washer-dryer, make

sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

Opening the porthole door manually

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

1. remove the plug from

the electrical socket.

2. make sure the water

level inside the machine is

lower than the door

opening; if it is not, remove

excess water using the

drain hose, collecting it in a

bucket as indicated in the

figure.

3. using a screwdriver,

remove the cover panel on

the lower front part of the

washer-dryer (see figure).

4. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its stop

position; pull downwards and open the door at the

same time.

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washer-dryer and help to prevent leaks.

 Unplug the washer-dryer when cleaning it and

during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

pre-chamber which protects the pump, situated in its

bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washer-dryer (see

figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make

sure that the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not

switch on.

The wash cycle does not start.

The washer-dryer does not take

in water (the indicator light for

the first wash cycle stage

flashes rapidly).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain

or spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The START/PAUSE indicator light

(orange) and the function

indicator lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washer-dryer door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see Personalisation).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washer-dryer to fill with water and

drain continuously. Special anti-draining valves are available in shops and

help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require

the drain phase to be started manually.

 The ANTI-CREASE function has been activated: To complete the wash

cycle, press the START/PAUSE button (Personalisation).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washer-dryer is not level (see Installation).

 The washer-dryer is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washer-dryers or hand and machine wash, or the like).

 Too much detergent was used.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set.

 The DRYING knob is on the

setting.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be

found on the front of the appliance by opening the door.

Românã

Sumar

Instalare, 14-15

Despachetare ºi punere la nivel

Racorduri hidraulice ºi electrice

Primul ciclu de spãlare

Date tehnice

Descrierea maºinii de spãlat ºi activarea

unui program, 16-17

Panoul de control

Indicatoare luminoase

Activarea unui program

Programe, 18

Tabel de programe

Personalizare, 19

Reglarea temperaturii

Alegerea programului de uscare

Funcþii

Detergenþi ºi rufe albe, 20

Compartimentul pentru detergenþi

Ciclu de albire

Pregãtirea rufelor

Articole delicate

Sistemul de echilibrare a încãrcãturii

Precauþii ºi sfaturi, 21

Norme de protecþie ºi siguranþã generale

Aruncarea reziduurilor

Deschiderea manualã a uºii

Întreþinere ºi curãþare, 22

Întreruperea alimentãrii cu apã ºi curent electric

Curãþarea maºinii de spãlat

Curãþarea compartimentului pentru detergent

Îngrijirea uºii ºi a tamburului

Curãþarea pompei

Controlarea furtunului de alimentare cu apã

Anomalii ºi remedii, 23

Asistenþã, 24

ARMXXL 105

Instrucþiuni de folosire

MAªINÃ DE SPÃLAT ªI USCAT

Instalare

 Este important sã pãstraþi acest manual pentru a-l

putea consulta în orice moment. În caz de vânzare,

de cesiune sau de schimbare a locuinþei, acesta

trebuie sã rãmânã împreunã cu maºina de spãlat

pentru a informa noul proprietar cu privire la

funcþionare ºi la respectivele avertismente.

 Citiþi cu atenþie instrucþiunile: veþi gãsi informaþii

importante cu privire la instalare, la folosire ºi la

siguranþã.

Despachetare ºi punere la nivel

Despachetare

1. Scoaterea din ambalaj a maºinii de spãlat.

2. Controlaþi ca maºina de spãlat sã nu fi fost

deterioratã în timpul transportului. Dacã este

deterioratã nu o conectaþi ºi luaþi legãtura cu

vânzãtorul.

3. Scoateþi cele 4

ºuruburi de protecþie

pentru transport ºi

cauciucul cu respectivul

distanþier, situate în

partea posterioarã

(a se vedea figura).

4. Închideþi orificiile cu dopurile din plastic aflate în

dotare.

5. Pãstraþi toate piesele: pentru cazul în care

maºina de spãlat va trebui sã fie transportatã,

piesele vor trebui montante din nou.

 Ambalajele nu sunt jucãrii pentru copii!

Punere la nivel

1. Instalaþi maºina de spãlat pe o suprafaþã planã ºi

rigidã, fãrã a o sprijini de ziduri, mobilã sau altceva.

2. Dacã podeaua nu este

perfect orizontalã,

compensaþi

neregularitãþile

deºurubând sau

înºurubând picioruºele

anterioare (a se vedea

figura); unghiul de

înclinare, mãsurat pe

planul de lucru, nu trebuie

sã depãºeascã 2°.

O nivelare precisã conferã stabilitate maºinii ºi evitã

vibraþii, zgomote ºi deplasãri pe timpul funcþionãrii.

În cazul mochetelor sau a unui covor, reglaþi

picioruºele astfel încât sã menþineþi sub maºina de

spãlat un spaþiu suficient pentru ventilare.

Racorduri hidraulice ºi electrice

Racordarea furtunului de alimentare cu apã

1. Introduceþi garnitura A

în extremitatea tubului de

alimentare ºi înºurubaþi-l

la un robinet de apã rece

cu gura filetatã (a se

vedea figura).

Înainte de conectare,

lãsaþi apa sã curgã pânã

când nu a devine

limpede.

2. Conectaþi tubul de

alimentare la maºina de

spãlat, înºurubându-l la

sursa de apã respectivã,

amplasatã în partea

posterioarã, sus în

dreapta (a se vedea

figura).

3. Fiþi atenþi ca furtunul sã nu fie nici pliat nici îndoit.

 Presiunea apei de la robinet trebuie sã fie cuprinsã

în valorile din tabelul Date tehnice (a se vedea

pagina alãturatã).

 Dacã lungimea furtunului de alimentare nu este

suficientã, adresaþi-vã unui magazin specializat sau

unui instalator autorizat.

 Nu folosiþi niciodatã tuburi folosite deja.

 Utilizaþi tuburile furnizate împreunã cu maºina.

65 - 100 cm

Conectarea furtunului de golire

Conectaþi furtunul de

golire - fãrã a-l îndoi - la

canalizare sau la

racordul de golire

prevãzut pe perete, la o

înãlþime de 65 - 100 cm

de sol;

Sprijiniþi-l de marginea

cãzii sau chiuvetei ºi

racordaþi ºina de ghidare

din dotare la robinet (a

se vedea figura).

Capãtul liber al

furtunului de golire nu

trebuie sã rãmânã

cufundat în apã.

 Nu se recomandã folosirea furtunurilor

prelungitoare; dacã este indispensabil, acestea

trebuie sã aibã acelaºi diametru ca ºi furtunul

original ºi nu trebuie sã depãºeascã 150 cm

lungime.

Racordarea electricã

Înainte de a introduce stecherul în prizã, asiguraþi-vã ca:

 priza sã fie cu împãmântare ºi conform

prevederilor legale;

 priza sã poatã suporta sarcina maximã de putere

a maºinii, indicatã în tabelul Date Tehnice

(a se vedea alãturi);

 tensiunea de alimentare sã fie cuprinsã în valorile

indicate în tabelul Date Tehnice (a se vedea

alãturi);

 priza sã fie compatibilã cu stecherul maºinii de

spãlat. În caz contrar înlocuiþi stecherul.

 Maºina de spãlat nu trebuie instalatã afarã, nici

chiar în cazul în care spaþiul este adãpostit,

deoarece este foarte periculoasã expunerea maºinii

la ploi ºi furtuni.

 Dupã instalarea maºinii de spãlat, priza de curent

trebuie sã fie uºor accesibilã.

 Nu folosiþi prelungitoare ºi prize multiple.

 Cablul nu trebuie sã fie îndoit sau comprimat.

 Cablul de alimentare trebuie sã fie înlocuit doar de

tehnicieni autorizaþi ai centrului de service ce apare

scris pe certificatul de garantie emis de producator.

Atenþie! Producãtorul îºi declinã orice

responsabilitate în cazul în care aceste norme nu se

respectã.

Primul ciclu de spãlare

Dupã instalare, înainte de folosire, efectuaþi un ciclu

de spãlare cu detergent ºi fãrã rufe, selectând

programul 1.

Date tehnice

Model

ARMXXL 105

Dimensiuni

lãrgime: 59,5 cm

înãlþime: 85 cm

profunzime: 53,5 cm

Capacitate

De la 1 la 7 kg pentru spãlare

De la 1 la 5 kg pentru uscare

Legãturi electrice

vezi eticheta cu caracteristicile tehnice,

aplicatã pe maºinã

Legãturi hidrice

presiune maximã: 1 MPa (10 bari)

presiune minimã: 0,05 MPa (0,5 bari)

capacitatea cuvei: 52 litri

Turaþia de

centrifugare

pânã la 1000 de rotaþii pe minut

Programe de control

în baza normei

EN 50229

Spãlare

: programul 6; temperatura

60°

efectuatã cu 7 kg de rufe.

Uscare

: prima uscare se efectueazã cu

kg de rufe ºi selectorul de USCARE în

poziþia ;

a doua uscare se efectueazã cu

kg de

rufe ºi selectorul de USCARE în

poziþia .

Acest aparat este conform cu

urmãtoarele Directive Comunitare:e

- 89/336/CEE din data de 03/05/89

(Compatibilitate Electromagneticã) ºi

modificãri succesive

- 2006/95/CE (Tensiuni Joase)

- 2002/96/CE

Zgomot

(dB(A) re 1 pW)

Spãlare: 66

Turaþie de centrifugare: 76

Sertarul detergenþilor: pentru a introduce

detergenþi sau aditivi (a se vedea Detergenþi ºi rufe

albe).

În interiorul sertarului pentru detergenþi este

amplasat un suport pe care se aflã schema

programelor.

Tasta PORNIRE/OPRIRE: pentru a porni ºi opri

maºina.

Selector PROGRAME: pentru a selecta programele.

Pe durata desfãºurãrii programului selectorul rãmâne

în aceeaºi poziþie.

Taste cu led FUNCÞII: pentru a selecta funcþiile

disponibile. Indicatorul corespunzãtor funcþiei alese

va rãmâne aprins.

Selector USCARE: pentru a regla uscarea doritã

(a se vedea Personalizare).

Selector TEMPERATURÃ: pentru a selecta temperatu-

ra sau spãlarea la rece (a se vedea Personalizare).

Indicatoare DESFÃªURARE CICLU/PORNIRE

ÎNTÂRZIATÃ: pentru a putea urmãri avansarea

programului de spãlare.

Indicatorul aprins aratã faza în curs de desfãºurare.

Dacã a fost selectatã funcþia Pornire întârziatã, va

fi indicat timpul care lipseºte pânã la pornirea

programului (a se vedea pag. alãturatã).

Indicator UªÃ BLOCATÃ: pentru a înþelege dacã uºa

se poate deschide sau nu (a se vedea pag.

alãturatã).

Tastã cu led START/PAUZÃ: pentru a activa / opri

momentan programele.

N.B.: pentru a întrerupe momentan un ciclu apãsaþi

aceastã tastã; ledul se va aprinde intermitent

(culoare portocalie) în timp ce ledul corespunzãtor

fazei în curs de desfãºurare va rãmâne aprins. Dacã

indicatorul UªÃ BLOCATÃ

este stins, atunci uºa

se poate deschide.

Pentru a continua spãlarea, de unde a fost

întreruptã, apãsaþi din nou tasta.

Descrierea maºinii de spãlat ºi

activarea unui program

Selector

TEMPERATURÃ

Sertarul detergenþilor

Indicatoare

DESFÃªURARE CICLU/

PORNIRE ÎNTÂRZIATÃ

Taste cu led

FUNCÞII

Tasta

PORNIRE/OPRIRE

Selector

USCARE

Indicator

UªÃ

BLOCATÃ

Tastã cu led

START/PAUZÃ

Panoul de control

Selector

PROGRAME

Indicatoare luminoase

Ledurile furnizeazã informaþii importante.

Iatã ce indicã:

Pornire întârziatã

Dacã a fost activatã funcþia Pornire întârziatã (a se

vedea Personalizare), dupã activarea programului, se

va aprinde intermitent ledul corespunzãtor

întârzieriiselectate:

Cu trecerea timpului, se va vizualiza întârzierea

restantã, prin aprinderea intermitentã a ledului

respectiv.

La expirarea întârzierii selectate, indicatorul luminos

se va stinge ºi programul selectat va intra în

funcþiune.

Indicatoare de fazã

Dupã alegerea ºi activarea ciclului dorit, indicatoarele

luminoase se vor aprinde unul dupã altul, ceea ce vã

indicã starea de avansare a programului:

Notã: în timpul fazei de Evacuare se va aprinde

indicatorul corespunzãtor cu Centrifugã.

Tastele de funcþii ºi ledurile corespunzãtoare

Alegerea unei funcþii implicã aprinderea ledului

corespunzãtor.

Dacã funcþia selectatã nu este compatibilã cu

programul ales, ledul corespunzãtor se va aprinde

intermitent iar funcþia nu se va activa.

În cazul în care va fi selectatã o funcþie

incompatibilã cu alta selectatã anterior, se va activa

doar ultima funcþie aleasã.

Indicator uºã blocatã:

Indicatorul luminos aprins indicã faptul cã uºa este

blocatã, ceea ce evitã deschiderea accidentalã;

pentru a evita orice daunã, este necesar sã se

aºtepte stingerea ledului, înainte de a deschide uºa.

N.B.: dacã funcþia Pornire întârziatã este activã,

uºa nu se poate deschide; pentru a o deschide,

apãsaþi tasta START/PAUZÃ pentru a întrerupe

momentan programarea.

 Aprinderea intermitentã rapidã a indicatorului

START/PAUZÃ (culoare portocalie) concomitent cu

un alt led indicã apariþia unei anomalii (a se vedea

Anomalii ºi remedii).

Activarea unui program

1. Porniþi maºina de spãlat apãsând pe tasta PORNIRE/OPRIRE. Toate indicatoarele se aprind câteva secunde,

apoi se sting; indicatorul START/PAUZÃ se va aprinde intermitent.

2. Introduceþi rufele ºi închideþi uºa.

3. Selectaþi programul dorit cu ajutorul selectorului de PROGRAME.

4. Reglaþi temperatura de spãlare (a se vedea Personalizare).

5. Selectaþi uscarea dacã este necesar (a se vedea Personalizare).

6. Adãugaþi detergentul ºi aditivii (a se vedea Detergenþi ºi rufe).

7. Alegeþi funcþiile dorite.

8. Activaþi programul apãsând tasta START/PAUZÃ; indicatorul luminos se va aprinde (culoare verde).

Pentru a anula un ciclu selectat, apãsaþi tasta START/PAUZÃ pentru a întrerupe momentan ciclul ºi alegeþi un

nou program.

9. La încheierea programului, indicatorul luminos

se va aprinde. Indicatorul UªÃ BLOCATÃ se va stinge,

ceea ce vã aratã cã uºa poate fi deschisã. Scoateþi rufele ºi lãsaþi uºa întredeschisã pentru a se putea usca

cuva si tamburul.

Opriti maºina de spãlat apãsând pe tasta PORNIRE/OPRIRE.

Spãlare

Clãtire

Centrifugã

Uscare

Sfârºit Spãlare

Notã: Imediat dupã alegerea

unui nivel sau a unei durate

de uscare, acest indicator

se va aprinde, ceea ce vã

aratã cã ciclul de spãlare

selectat va fi urmat de o

fazã de uscare.

Programe speciale

STERILIZARE (programul 6). Un program de igienizare la temperaturã ridicatã, care presupune folosirea

decolorantului (temperatura este peste 60°C).

Pentru a decolora rufele, turnaþi decolorantul, detergentul ºi

aditivii în sertarele corespunzãtoare (a se vedea paragraful Compartimentul pentru detergenþi).

CICLU DE SPALARE NOCTURNA (programul 7). Este un ciclu cu zgomot redus, care vã permite folosirea

maºinii pe timp de noapte. Programul a fost conceput pentru articolele sintetice ºi din bumbac. La încheierea

ciclului, maºina se opreºte cu apã în cuvã; pentru a stoarce rufele ºi a goli apa apãsaþi tasta START/PAUZÃ,

daca nu, dupã 8 ore maºina comandã automat stoarcerea ºi evacuarea apei.

CICLU BABY (programul 8). Programul îndepãrteazã eficient atât mizeria care pãteazã în mod obiºnuit hainele

copiilor cât ºi detergentul, în scopul de a evita apariþia unor alergii pe pielea delicatã a celor mici. Ciclul a fost

conceput pentru a diminua încãrcarea bacterianã prin folosirea unei cantitãþi de apã mai mari ºi prin optimizarea

aditivilor speciali de igienizare, adãugati la detergent.

La încheierea ciclului de spãlare, maºina efectueazã o rotaþie lentã a cuvei, pentru a limita ºifonarea; pentru a

termina ciclul, apãsaþi tasta START/PAUZÃ.

MIX 30' (programul 4) a fost studiat pentru a spãla articolele puþin murdare, în mod rapid: dureazã doar 30 de

minute ceea ce economiseºte energie ºi timp. Selectând programul (4 la 30°C) este posibilã spãlarea

articolelor din materiale diferite (excluse lâna ºi mãtasea) cu o greutate maximã de 3 kg.

MIX 15' (programul 5) a fost studiat pentru a spãla articolele foarte puþin murdare, în mod rapid: dureazã doar 15

de minute ceea ce economiseºte energie ºi timp. Selectând programul (5 la 30°C) este posibilã spãlarea

articolelor din materiale diferite (excluse lâna ºi mãtasea) cu o greutate maximã de 1,5 kg.

Programe

Datele specificate în tabel au valoare indicativã.

Pentru toate Instituþiile de Testare:

1) Programul de control conform normei EN 50229: selectaþi programul 6 ºi temperatura de 60°C.

2) Program pentru bumbac, prelungit: selectaþi programul 1 ºi temperatura de 40°C.

3) Program

pentru

bumbac, rapid: selectaþi programul 2 ºi temperatura de 40°C.

Tabel de programe

Programe

Detergenþi

Descrierea Programului

Temp.

max.

(°C)

Viteza max.

(rotaþii pe

minut)

Decolorant Spãlare

Balsam

rufe

Uscare

Sarcina

Max.

(Kg)

Durata ciclului de

spãlare

Programe Speciale

STERILIZARE:

Rufe albe foarte murdare.

90° 1000

•



•

170

STERILIZARE (1):

Albe ºi colorate rezistente foarte

murdare.

60° 1000 -

•

153

CICLU DE SPÃLARE NOCTURNÃ:

Colorate

delicate puþin murdare.

40° 800 -

•

290

CICLU BABY:

Colorate delicate foarte murdare.

40° 800 -

•

118

MÃTASE /PERDELE:

Pentru articolele din

mãtase, viscozã, lenjerie.

30° 0 -

•

LÂNÃ:

Pentru articole din lânã, caºmir.

40° 800 -

•

1,5

Programe zilnice

RUFE ALBE BUMBAC:

Albe ºi colorate rezistente

foarte murdare.

60° 1000

•

7 122

RUFE ALBE BUMBAC (2):

Albe ºi colorate delicate

foarte murdare.

40° 1000

•

7 115

COLORATE BUMBAC (3):

Albe puþin murdare

ºi colorate delicate.

40° 1000

•

7 85

SINTETICE REZISTENTE:

Colorate rezistente

foarte murdare.

60° 800 -

•

3 85

SINTETICE DELICATE:

Colorate rezistente

puþin murdare.

40° 800 -

•

3 70

MIX 30’:

Pentru a spãla rapid articolele puþin

murdare (nu este indicat pentru lânã, mãtase ºi

articole de spãlat cu mâna).

30° 800 -

•

3 30

MIX 15':

Pentru a împrospãta rapid articolele

puþin murdare (nu este indicat pentru lânã,

mãtase ºi articole de spãlat cu mâna).

30° 800 -

•

1,5 15

Programe parþiale

CLÃTIRE - 1000 - -

•

7 36

CENTRIFUGARE - 1000 - - -

•

7 16

EVACUARE - 0 - - - - 7 2

Programe de uscare

USCARE

Bumbac

- - - - -

•

5 -

USCARE

Sintetice

- - - - -

•

3 -

USCARE

Lânã

- - - - -

•

1,5 -

Reglarea temperaturii

Rotind selectorul de TEMPERATURÃ se fixeazã temperatura de spãlare (a se vedea Tabelul programelor).

Temperatura poate fi redusã pânã la spãlarea la rece (

Maºina va împiedica în mod automat de a alege o temperaturã mai mare decât maxima admisã pentru fiecare program.

Alegerea programului de uscare

Rotind selectorul USCARE se determinã modalitatea de

uscare doritã. Sunt prevãzute douã posibilitãþi:

A - În funcþie de duratã: de la 40 la 180 de minute.

B - În funcþie de umiditatea rufelor:

Cãlcare

: rufe puþin umede, uºor de cãlcat.

Uscate

: rufe uscate de pus în dulap.

Dulap

: rufe foarte uscate, indicatã pentru prosoape ºi

halate de baie.

Dacã, în mod excepþional, cantitatea de rufe de spãlat ºi uscat este superioarã cantitãþii maxime prevãzute (vezi

tabelul programelor), efectuaþi spãlarea, iar la terminarea programului, împãrþiþi cantitatea de rufe în mai multe pãrþi ºi

uscaþi-le separat.

Urmaþi apoi instrucþiunile prevãzute pentru efectuare programului Doar uscare.

Repetaþi aceleaºi operaþiuni pentru rufele rãmase.

N.B: Dupã încheierea programului de uscare, maºina va efectua o rãcire, chiar dacã selectorul de USCARE este

adus în poziþia

Doar uscare

Rotiþi selectorul de PROGRAME într-una din poziþiile de uscare (11-12-13) disponibile, în funcþie de tipul de

material; selectaþi apoi modalitatea de uscare doritã, cu ajutorul selectorului de USCARE.

Funcþii

Diferitele funcþii de spãlare prevãzute pentru maºina de spãlat, permit obþinerea unor rufe curate ºi albe, dupã dorinþã.

Pentru a activa funcþiile:

1. apãsaþi tasta corespunzãtoare funcþiei dorite;

2. aprinderea ledului respectiv indicã activarea funcþiei.

Notã: Semnalul luminos intermitent, rapid, indicã faptul cã funcþia respectivã nu este compatibilã cu programul ales.

Pornirea întârziatã

Întârzie pornirea maºinii cu pânã la 9 de ore.

Apãsaþi de mai multe ori pânã la aprinderea butonului cu întârzierea doritã. La a cincea apãsare a tastei, funcþia se

va dezactiva.

N.B.: Dupã apãsarea tastei START/PAUZÃ, se va putea modifica întârzierea doar diminuând-o.

 Se poate activa pe toate programele.

Clãtire suplimentarã

Selectând aceastã opþiune, clãtirea va fi mai eficientã, ceea ce asigurã eliminarea totalã a detergentului din

rufe. Este recomandatã cu precãdere persoanelor cu pielea sensibilã.

 Nu poate fi activatã pe programele 4, 5, 11, 12, 13, B, C.

Super spãlare

Mulþumitã utilizãrii unei cantitãþi mai mari de apã în faza iniþialã a ciclului ºi duratei de timp îndelungate,

aceastã funcþie garanteazã o spãlare de mare performanþã.

 Nu poate fi activatã pe programele 4, 5, 6, 9, 10, 11, 12, 13, A, B, C.

1000-500

Apãsând aceastã tastã se reduce viteza de stoarcere.

 Nu poate fi activatã pe programele 9, C, 11, 12, 13.

Personalizare

Tipul

þesãturii

Tipul sarcinii Sarcinã

max (kg)

Dulap Uscate Cãlcare

Bumbac Rufe de diverse dimensiuni,

Prosoape din bumbac eponjat

5 180 170 160

Sintetice Cearºaf, Cãmãºi, Pijamale,

ºosete, ecc.

3 180 170 160

Lânã 1,5 150 140 130

Tabel Duratã Uscare (valori indicative)

Detergenþi ºi rufe albe

Compartimentul pentru detergenþi

Un rezultat bun la spãlare depinde ºi de dozarea

corectã a detergentului: excesul de detergent nu

garanteazã o spãlare mai eficientã, ci contribuie la

deteriorarea pãrþilor interne ale maºinii de spãlat ºi

la poluarea mediului înconjurãtor.

 Nu introduceþi în maºinã detergenþii pentru

spãlarea manualã deoarece formeazã prea multã

spumã.

Deschideþi

compartimentul pentru

detergenþi ºi introduceþi

detergentul sau aditivul

dupã cum urmeazã:

compartiment 1: Detergent pentru prespãlare

(sub formã de praf)

Înainte de a adãuga detergentul verificaþi ca sertarul

adiþional 4 sã nu fie introdus.

compartiment 2: Detergent pentru spãlare

(sub formã de praf sau lichid)

Detergentul lichid trebuie vãrsat doar înainte de pornire.

compartiment 3: Aditivi

(soluþie de înmuiat, balsam rufe etc.)

Soluþia de înmuiat nu trebuie sã iasã deasupra

grãtarului.

compartiment adiþional 4: Decolorant (Inãlbitor)

Ciclu de albire

Albirea poate fi efectuatã numai cu programele 1, 2, 6.

Turnaþi decolorantul în compartimentul adiþional 4, iar

detergentul ºi balsamul de rufe în compartimentele

corespunzãtoare, apoi alegeþi unul din ciclurile descrise

mai sus. Este indicat numai pentru articole din bumbac

foarte murdare.

Pregãtirea rufelor

 Sortaþi rufele în funcþie de:

- tipul de material / simbolul de pe etichetã.

- culori: separaþi rufele colorate de cele albe.

 Goliþi buzunarele ºi controlaþi nasturii.

 Nu depãºiþi valorile indicate, referitoare la

greutatea rufelor uscate:

Þesãturi rezistente: max 7 kg

Materiale sintetice: max 3 kg

Þesãturi delicate: max 2 kg

Lânã: max 1,5 kg

MAX

Cât cântãresc rufele?

1 cearceaf 400-500 g.

1 faþã de pernã 150-200 g.

1 faþã de masã 400-500 g.

1 halat de baie 900-1.200 g.

1 prosop 150-250 g.

Articole delicate

Mãtase: utilizaþi programul special 9 pentru spãlarea

articolelor din mãtase. Se recomandã folosirea unui

detergent special pentru articole delicate.

Perdele:

împãturiþi-le ºi aºezaþi-le într-o faþã de pernã

sau într-un sac de tip plasã. Utilizaþi programul 9.

Lânã: Hotpoint/Ariston este unica maºinã de spãlat

recunoscutã de Woolmark Company, care i-a acordat

Woolmark Platinum Care (M.0508), ca garanþie a

calitãþii de spãlare cu maºina a tuturor articolelor de

lânã, inclusiv a celor care au pe etichetã menþiunea a

se spãla manual

. Cu programul 10 puteþi deci

spãla la maºinã, în cea mai mare siguranþã, toate

articolele din lânã (max. 1,5 kg) cu garanþia de a

obþine cele mai performante rezultate.

Sistemul de echilibrare a încãrcãturii

Pentru a evita trepidaþiile excesive, înainte de

stoarcere, cuva maºinii va distribui cantitatea de rufe

în mod uniform, centrifuga efectuând câteva rotaþii la

o vitezã mai mare decât viteza de spãlare. Dacã,

dupã numeroase încercãri, maºina nu reuºeºte sã

echilibreze greutatea, stoarcerea rufelor se va face

la o vitezã mai micã decât cea prevãzutã în program.

Dacã instabilitatea este prea mare, maºina va

distribui greutatea în locul centrifugei. Pentru a

favoriza o mai bunã repartizare a rufelor ºi

echilibrarea corectã a maºinii, se recomandã sã

introduceþi în maºinã atât articole mari cât ºi mici.

Antiºifonare

Aceastã funcþie întrerupe programul de spãlare

menþinând rufele la înmuiat în apã înainte de golirea

maºinii.

Poate fi activatã numai cu programul 9 (Mãtase/

Perdele) ºi serveºte la evitarea formãrii pliurilor.

Pentru a termina ciclul, apãsaþi tasta START/

PAUZÃ.

La pagina sta caricando ...

Indesit ARMXXL 105 (EU) Guida utente

Marca: Indesit

Modello: ARMXXL 105 (EU)

Categoria: Lavatrici

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

slovenčina: Indesit ARMXXL 105 (EU) Užívateľská príručka
română: Indesit ARMXXL 105 (EU) Manualul utilizatorului

Indesit ARMXXL 105 (EU) Guida utente

Indesit ARMXXL 105 (EU) Guida utente

in altre lingue

Documenti correlati

Altri documenti