Otsein-Hoover OHNWF 6127-37 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente
Instruction Book
OHNWF 6167
Washer/Dryer
40001884Eng.qxd 27/09/2004 18:02 Page 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Delivery information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Do’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Don’ts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Choose a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electricity supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting to the cold water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connection of the machine to the drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Moving the machine into position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Testing the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Washing and Drying advice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Loading your washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sorting the laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dispensing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wash and Dry Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Programme Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Special Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Daily Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
A Typical Wash and Dry Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Selecting the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Starting the cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cleaning and Routine Maintenance. . . . . . . . . . . . . . . . . . . . 31
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
40001884Eng.qxd 27/09/2004 18:02 Page 2
Introduction
Please read and follow these instructions
carefully and operate the machine accordingly.
This booklet provides important guidelines for
safe use, installation, maintenance and some
useful advice for best results when using your
machine.
Keep all documentation in a safe place for future
reference or for any future owners.
Delivery information
Please check that the following items are
delivered with the appliance:
Instruction manual
Guarantee card
Blanking plug
Inlet hose & hooked end support
(see Unpacking and Installation Instructions)
Base panel & x2 push clips
Energy Label
Do’s
All packaging materials used are
environmentally-friendly and recyclable.
Please help dispose of the packaging via
environmentally-friendly means. Your local
council will be able to give you details of
current means of disposal.
To ensure safety when disposing of an old
washing machine disconnect the mains plug
from the socket, cut the mains power cable
and destroy this together with the plug. To
prevent children shutting themselves in the
machine break the door hinges or the door
lock.
This machine is solely for domestic use,
i.e. to wash, rinse and spin dry household
textiles and garments.
3
Check that no
damage has
occurred to the
machine during
transit. If it has,
call for service
by GIAS.
40001884Eng.qxd 27/09/2004 18:02 Page 3
Don’ts
Do not touch the appliance when hands or
feet are damp or wet.
Do not lean on the door when loading the
machine or use the door to lift or move the
machine.
Do not use adapters, multiple connectors
and/or extensions.
Do not allow children to play with the
machine or its controls.
Do not try to open the door when water is
visible in the drum or the Seguridad Puerta
indicator is on.
4
Failure to
comply with
the above can
compromise the
safety of the
appliance. You
may be charged
for a service call
if a problem
with your
machine is
caused by
misuse.
If the appliance
is not running
properly or
breaks down,
switch it off,
disconnect the
plug from the
socket, turn off
the water
supply and do
not tamper
with the
appliance.
Consult GIAS
Service for
possible repair.
40001884Eng.qxd 27/09/2004 18:02 Page 4
Unpacking the product
Remove the machine from its packaging close to
the final location of the machine.
1. Cut carefully around the base of the
packaging.
2. Lay the machine on its back and remove the
base and the two polystyrene spacers on
each side of the machine. We recommend
that a second person assist in the lifting and
manoeuvring of the machine.
3. Return the machine to the upright position,
remove the remainder of the packaging and
the central screw in the transit bar.
4. Remove the four retaining screws in the
transit bar and pull out the transit bracket.
5
Dispose of the packaging safely.
Make sure it is out of the reach
of children, it is a potential
source of danger.
40001884Eng.qxd 27/09/2004 18:02 Page 5
5. Take the base panel provided and fit the
two self adhesive strips by removing the
backing paper on one side and locating the
strips on each side of the base panel.
6. Tilt the machine forward and locate the
base panel under the front of the machine.
Remove the remaining backing paper from
the self-adhesive strips and offer up the
base panel to the bottom of the cabinet.
7. Take the two plastic fixing clips and fix the
base panel to the base of the machine.
Bring the machine back to the upright
position.
6
We recommend you keep the transit bracket and
screws to protect the machine for future transit.
The manufacturers will not be responsible for any
damage to the machine caused by not following the
instructions relating to releasing the transit protection.
The user is responsible for all installation costs.
40001884Eng.qxd 27/09/2004 18:02 Page 6
8. Cover the central hole in the rear of the
machine with the cap enclosed in the
instruction bag.
Choose a location
After the machine has been installed, ensure
that the mains plug and water supply valves
are easily accessible.
Make sure there is enough space for the
machine. Select a space at least 600mm wide
and 850mm high. Also leave enough space
to open the door fully so you can load and
unload it easily.
Keep the area underneath and around the
machine free of combustible materials such
as lint, paper, rags, chemicals etc.
7
Installation
Do not plug the
machine in and
switch it on at
the mains until
the installation
is completed.
40001884Eng.qxd 27/09/2004 18:02 Page 7
Electricity supply
Washing machines are supplied to operate at a
voltage of 230V, 50 Hz single phase. Check that
the supply circuit is rated to at least 16A.
Electricity can be extremely dangerous.
This washing machine must be earthed.
The socket outlet and the plug on the appliance
must be of the same type.
Do not use multiple adapters and/or extension
leads.
The wires in the mains lead are coloured in
accordance with the following codes:
Blue NEUTRAL
Brown LIVE
Green and Yellow EARTH
CE Appliance complies with European Directive
89/336/EEC, 73/23/EEC and subsequent
amendments.
Water supply
The cold water pressure should be between
0.05-0.8 Mpa.
Do not connect the machine to a single
outlet instantaneous water heater.
The water supply tap should be accessible
when the machine is installed.
Before connecting the fill hose, check that
the water is running from the water supply
tap to be used.
8
You may be
charged for a
service call if a
problem with
your machine is
caused by
incorrect
installation.
If the mains
cord on this
appliance is
damaged, it
must be
replaced by a
special cord
which is ONLY
obtainable from
the GIAS spares
service. It must
be installed by
a competent
person.
40001884Eng.qxd 27/09/2004 18:02 Page 8
Connecting to the cold
water supply
This machine has an inlet hose with a 19mm
(3/4") threaded ferrule fitted to the end, to
attach between the threaded connector on the
appliance and the water supply.
Only use the new hose supplied to connect the
machine and ensure that the sealing washers are
in place inside the hose connectors.
Do not re-use old hoses which are attached to
existing installations.
Do not over-tighten the connections. Hand tight
is sufficient.
Do not trap or kink the hose.
1. Connect the elbow end of the hose provided
to the threaded inlet on the back of the
machine.
Grey pipe to the white threaded inlet on
the machine.
2. Hand tighten the connector.
3. Connect the straight ends of the pipes to
the water supply; ensure that there are no
kinks.
4. Turn on the water supply and check for
leaks. If there is a leak, turn off the water
supply, disconnect the hose and check the
sealing washers are in place. Refit the hose
and turn on the water supply.
9
40001884Eng.qxd 27/09/2004 18:02 Page 9
Connection of the machine to the
drain
This machine must be connected in accordance with the water supply
regulations. Water byelaws prohibit connection to a surface water drain.
Decide which plumbing option suits you best then follow the instructions
below.
Option 1
Waste pipe connection (waste trap)
Fit the hooked end support to the outlet pipe. Position at least 800mm off the
floor.
After removing the blanking plug or cutting the membrane from the waste
system securely fix the outlet pipe to the drainage system, using a hose clip.
Secure the hooked end support up to at least 800mm to avoid water being
drawn back into the machine.
10
All machines are tested with water prior to leaving the
factory so a small amount of water may remain in the
drum and drain hose.
Flooding could occur if any part of the installation is
not completed correctly.
800 mm
hose clip
hooked end support
sink
flexible
discharge hose
trap with hose
adaptor
40001884Eng.qxd 27/09/2004 18:02 Page 10
Option 2
Into a standpipe
Ensure that the standpipe is not located near
an electrical socket.
Fit the hooked end support to the outlet pipe.
Install the hose into the standpipe ensuring
that the pipe is at least 500mm from the floor.
Insert the outlet pipe approximately 100mm
into the standpipe.
Moving the machine
into position
Your machine is heavy so care must be taken
when moving it. We recommend that two people
move the machine to avoid strain and possible
injury.
Take care not to damage flooring when
moving the machine.
When moving the machine to its final
position take care not to kink or damage
the hose at the back of the machine.
Adjusting the feet
Once the machine is in place the feet should be
adjusted to ensure that the machine is level. If
the machine is not level it may become noisy or
move.
Adjust the feet on the front corners of the
machine until the machine is firm and level.
When the machine is firm and level, tighten the
locking nuts on the two feet.
11
Do not drag or
lift the machine
by its door.
100 mm
500 mm min
40001884Eng.qxd 27/09/2004 18:02 Page 11
Refer to the programme guide for details of how
to select programmes.
1. Turn on the water supply and check for
leaks from the fill hose.
2. Switch on the electricity supply.
3. Select the spin programme / and
then press the Start Pausa button to start
the machine. Allow the programme to
continue for one minute and then cancel
the programme by returning the selector to
the OFF position. This will remove any water
remaining in the machine from factory
testing.
4. To check for cold water filling to the
machine:
Select the rinse programme / and
press the Start Pausa button to start the
machine.
Allow the tumble action to continue until
the water has pumped out. Check that the
drain outlet is not leaking or overflowing.
5. Switch off the machine at the end of the
cycle by turning the programme knob to the
OFF position.
6. Select the spin programme / and
press the Start Pausa button to start the
machine. If the machine takes longer than
one minute to empty check the drain hose
for kinks.
Installation testing is now
complete.
Now you have successfully installed the machine
we advise that you run the machine to ensure the
drum is thoroughly clean after testing and
storage. Select the Algodón Resistentes
programme and run the machine for a complete
cycle using only wash detergent and water. Ensure
that the drying timer is in the OFF position.
12
Testing the installation
This
programme
will take
approximately
2 hours to
complete.
40001884Eng.qxd 27/09/2004 18:03 Page 12
The following tips are designed to assist in getting the best results from your
machine whilst utilising it in the most environmentally-friendly and
economical way. It is also important to understand the items to avoid in your
laundry, to ensure the continued safe and reliable operation of your machine.
Loading your washing machine
To make further reductions of energy, water and detergent consumption, we
recommend that you put a full load into your machine. Energy savings of up
to 50% can be achieved by washing one full load compared to two half loads.
Do not overload the machine as this will reduce the quality of the wash and
may cause damage to the machine and your laundry.
When is prewashing really needed?
Only with particularly dirty loads! Energy savings of 5 to 15% are made by not
selecting the prewash option for less dirty laundry. Pre-treat awkward stains
with a washable stain remover.
Which wash temperature should you choose?
Using stain removers before machine washing reduces the need to wash at
temperatures over 60°C.
Using a 40°C wash temperature can make energy savings of up to 50%.
Heavily soiled laundry
To ensure the best performance when washing a particularly dirty load, we
recommend that you reduce the amount of items to be put into the machine.
Allowing more space in the drum the items can circulate more freely and will
wash cleaner.
Sorting the laundry
Items to avoid
We recommend that you do not wash underwired bras in the machine. Should
the wires become detached it could cause damage to your clothes and the
machine. If the washcare label states that the bra is machine washable then
we advise placing it in a wash bag.
Recommendations
Always follow the wash care labelling on the garments.
Fasten zips, tie strings and close press studs to prevent tangling. Ensure that
pockets are emptied of loose change and other small items.
13
Washing and Drying advice
40001884Eng.qxd 27/09/2004 18:03 Page 13
Check that there are no metal objects in the laundry as these may damage the
laundry and the machine. Place small items in a wash bag.
Drying
In addition to the above advice the guidelines below must be followed when
drying the clothes.
Sort the load for drying:
By care symbols:
These can be found on the collar or inside seam:
Suitable for tumble drying. Tumble drying at high temperature.
Tumble drying at low temperature only. Do not tumble dry.
If the item does not have a care label it must be assumed that it is not suitable
for tumble drying.
By amount and thickness
Whenever the load is bigger than the dryer capacity, separate clothes
according to thickness (e.g. towels from thin underwear).
By type of fabric
Cottons/linen: Towels, cotton jersey, bed and table linen.
Synthetics: Blouses, shirts, overalls, etc. made of polyester or polyamid, as
well as for cotton/synthetic mixes.
Things to avoid
Do not tumble dry woollens, silk, delicate fabrics, nylon stockings,
delicate embroidery, fabrics with metallic decorations, garments with PVC
or leather trimmings, training shoes, bulky items such as sleeping bags, etc.
Do not dry articles which have been treated with a dry cleaning fluid or
rubber clothes (danger of fire or explosion).
Foam rubber materials can, under certain circumstances, when heated
become ignited by spontaneous combustion. Foam plastic, foam rubber
and rubber-like material are not suitable for tumble drying. Articles
made from these materials MUST NOT be placed in the dryer.
Do not try to dry items that are dripping wet, this may damage the
appliance. Spin these items first.
14
Do not use the machine to wash and dry items that do not
have a wash label.
Do not wash and dry items previously treated with solvents.
40001884Eng.qxd 27/09/2004 18:03 Page 14
Detergent dosage
Only use detergents which are suitable for use in a washing machine. You will
obtain the best results from your wash with the minimum use of chemical
products, and the best care for your laundry if you take into consideration the
degree of soiling as well as the type of detergent to choose.
The amount of detergent to use depends on:
Water hardness.
Depending on the hardness of the water and the type of detergent used,
it is possible to reduce the amount of detergent.
The softer the water supply, the less detergent is required.
The degree of soiling.
It is possible to reduce the amount of detergent used depending on the
degree of soiling.
Use less detergent for less soiled items.
Amount of laundry.
It is possible to reduce the amount of detergent when washing only a
small amount of laundry.
For smaller loads use less detergent.
The dosages shown on the packaging of detergents for washing delicates
often already refer to a reduced wash size. Always follow the dosage
instructions on the detergent packaging.
15
The Dispenser
DO NOT exceed the maximum detergent dosage
COMPARTMENT I
Prewash detergent
Maximum dosage 100ml of powder
COMPARTMENT II
Mainwash detergent
Maximum dosage 200ml
of powder
COMPARTMENT
Fabric Conditioner
Maximum dosage 100ml
40001884Eng.qxd 27/09/2004 18:03 Page 15
Dispensing instructions
The detergent drawer is split into 3 compartments:
the first, labelled "I", is for detergent utilised
during Prewash.
the second, labelled "II", is for detergent
utilised during the main wash.
the third, labelled is for special additives
such as fabric softeners, fragrances, starch,
brighteners etc.
Dispensing in the drum
Liquid detergents and some tablets are dispensed
via the machine drum using the recommended
dispensing device which is placed upright on top of
the washload towards the back of the drum. Some
tablets are designed to be placed in the dispenser
drawer, check the detergent pack for details.
16
Do not put any
items into the
drawer other
than detergents
that are
designed to be
dispensed from
the drawer as
they may cause
blockage or
damage.
40001884Eng.qxd 27/09/2004 18:03 Page 16
Turning the machine On
The machine is turned on by selecting a programme via the programme
selector. This status will be indicated by the STOP indicator light flashing, this
light will continue to flash until the machine has started or the machine is
returned to the OFF position.
Start/Pause (Start Pausa)
Start
After selecting the programme and the required options press the Start Pausa
button once to start the machine. The STOP light will stop flashing and START
light will illuminate and there will be a short time delay to the start of the
programme while the machine sets the wash parameters for the selected
programme and options. If the duration of the programme you have selected
17
The Control Panel
The programme selector must be returned to the OFF
position to reset the controls between each wash cycle.
CHRONOVISION
Display
Door Locked Indicator
(Seguridad Puerta)
Start/Pause
(Start
Pausa)
Start Delay
(Inicio
Diferido)
Pre Wash
(Pre Lavado)
Extra Rinse
(Aclarado
No Alérgias)
Spin Speed
Reduction
(Centrifuga
Suave)
Drying Time
Selector
(Tiempo De
Secado)
Temperature
Selector
(Temperatura °C)
Programme
Selector
40001884Eng.qxd 27/09/2004 18:03 Page 17
is shorter than 60 minutes, then the time
remaining indicator will illuminate accordingly.
The Seguridad Puerta indicator light will also
illuminate a few seconds after pressing the Start
Pausa button.
Pause (Pausa)
The programme may be paused at any time
during the wash cycle by holding down the Start
Pausa button for about two seconds. When the
machine is in the paused mode, the time
remaining for the programme in the
CHRONOVISION indicator and option buttons will
flash. The Seguridad Puerta indicator light will
remain illuminated for approximately 2 minutes.
The door can be opened when this indicator goes
out. To restart the programme, press the Start
Pausa button once again.
Cancelling and changing the
programme
To cancel the programme the programme selector
should be rotated to the OFF position.
Select a new programme and start as detailed
above.
Door Locked indicator
(Seguridad Puerta)
The Seguridad Puerta indicator light is
illuminated when the door is fully closed and the
machine is ON.
When Start Pausa is pressed on the machine with
the door closed the indicator will flash
momentarily and then illuminate. If the door is
not closed the indicator will continue to flash.
A special safety device prevents the door from
being opened immediately after the end of the
cycle. Wait for 2 minutes after the wash cycle has
finished and the Seguridad Puerta light has gone
out before opening the door. As a safety
measure, check that there is no water evident in
the drum. At the end of the cycle turn the
programme selector to OFF.
If the programme is paused, the Seguridad Puerta
indicator will go out after 2 minutes and the door
18
When starting a
subsequent
wash cycle the
programme
selector must
be returned to
OFF prior to the
next
programme
being selected
and started.
40001884Eng.qxd 27/09/2004 18:03 Page 18
can be opened. Check there is no water evident
in the drum before opening the door.
CHRONOVISION
In order to better manage your time, this washing
machine features an indicator light system that
keeps you constantly informed on the remaining
cycle time and the status of the start delay
function.
When a drying time is selected the
CHRONOVISION display will display the time
remaining on the washing programme when the
washing is taking place and the time remaining in
the drying phase when drying is taking place.
19
START
60'
30'
15'
STOP
Remaining time above
60 minutes
Remaining time less
than 60 minutes
Remaining time less
than 30 minutes
Remaining time less
than 15 minutes
End of the programme
3h
6h
9h
3 hours or less remaining
before the programme
commences
6 hours or less remaining
before the programme
commences
9 hours or less remaining
before the programme
commences
CHRONOVISION DISPLAY
WASH PROGRESS
START DELAY
40001884Eng.qxd 27/09/2004 18:03 Page 19
Start Delay (Inicio Diferido)
This option is available to delay the start of the wash cycle by up to 9 hours.
The selection of the time is completed by pressing the Inicio Diferido button,
the CHRONOVISION display will indicate the time selected. When the correct
delay is selected press the Start Pausa button to start the cycle.
Prewash (Pre Lavado)
This option is available on the cottons and synthetics programmes. Prewash is
automatic on the Sports programme. This option is particularly useful for heavily
soiled loads and can be used before selecting the main wash programme.
Detergent for this programme should be added to the first compartment of the
soap drawer labelled "I" (Please refer to Detergent Drawer section of manual).
We recommend you only use 20% of the main wash detergent quantity.
Extra Rinse (Aclarado No Alérgias)
This option is available on the cottons programmes. The option increases the
number of rinses to five (including the final conditioned rinse). This can help
prevent skin irritation from detergent residue for people with particularly
sensitive skin. Selecting the (Aclarado No Alérgias) button is also
recommended when washing heavily soiled fabrics which need a lot of
detergent, or when the wash load contains towelling fabrics that have a
greater tendency to retain detergent.
Spin Reduction (Centrifuga Suave)
This option is available on the Cottons programmes (Algodón Resistentes, Colores,
Delicados), AA 40°C, Lavado Clase A 59' , Sport and Daily (Rápido 29', Rápido
44') programmes to reduce the maximum spin speed to 600rpm thus reducing
creasing. It is not recommended that this option be selected when a drying
programme will follow, as the length of the drying cycle will be increased.
Temperature Selector (Temperatur °C)
The washing machine is equipped with a temperature selector knob to set the
temperature you require. Bigger energy savings can be achieved by using the
lower temperature settings around the dial between and 40°C. By
selecting the position, the wash temperature is limited to the water inlet
temperature, thus reducing energy consumption further. We recommend that
the temperature shown on wash care garments should never be exceeded.
20
Wash and Dry Options
The options should be selected BEFORE pressing the
Start Pausa button
40001884Eng.qxd 27/09/2004 18:03 Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Otsein-Hoover OHNWF 6127-37 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente