Sanyo CZP2141TX Manuale utente

Categoria
TV LCD
Tipo
Manuale utente
Instruction
Manual
Colour
Television
Model CZP 2141 TX
----,
TELETEXT
SPECIAL FUNCTIONS
CHANNEL SCANNING
Electric Mains
Specifications
, The TV receiver is manufactured to utilize an AC Voltage
Source of 230 Volts, 50 Hz.
Safety Precaution
When the TV receiver is not to be used for an extended period
of time, it is advisable to disconnect the AC power cord from
the AC outlet.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain
or moisture.
High voltages are used in the operation of this TV set.
Do not remove the back from your set. Refer servicing to quali-
fied service personnel.
Aerial Connection
Connect the cable with a plug from a UHF (or VHF) aerial to
the Ir aerial socket on the cabinet back.
Power Source ................... AC 230V, 50Hz
Television System ............ System B/G
Colour System .................. PAL
Channel Coverage ............ VHF :1 11
UHF :21 69
Aerial Input Impedance ....75 ohm
.&.-
,lr aerial socket
For all aerial circuit problems please consult your local dealer.
Batterv Installation (Remote Control Transmitter)
Remove the battery cover by sliding.
Install two “AA” 1.5 volt batteries so that the +“ and -”
marks on the batteries match the”+” and “–” marks inside
the unit.
Close the battery cover.
Note: Replace the batteries when the TV set is showing the fol-
lowing symptoms:
Operation is unsteady or erratic, sometimes the TV set
does not work with transmitter. Discharged batteries
may leak and damage the unit. The normal life of batter-
ies should be from nine to ten months.
–l–
Controls
-Standby and Power Indicator
Q
~
L-
- Mains ON/OFF Switch
4
so.”.
@cm- _ ,“% + ,ELECT
8
m.ml
Remote Control Detector
cat,
L
Headphone Jack
YJ
~ Programme Selector
SELECT button
‘%=
‘rogrammese’ectorl111+71+
3=
h a a o
Power ON/OFF
6 a
&
1 111—
5 A ‘“’E
TVIAV Selector
D
3 GJ ‘LT
I ALT (Alternate)
I
1-
lug_~
la
e
+-+
x$
@ Off timer
——
d
~ Normalization ~
Colour
#
Brightness
#
/
Contrast
:
U/:
E
-..
U Memory
)
c>
LIA
-@ Channel Scanning
20
d—@-l r
A
---- . . ... m,-
7
a
~ Recall
I
I
I
L
I
J
J
@
BAND Selector
This button is not used
for this model.
Remote Control Transmitter
–2–
General Operation
Usually the Remote Control Transmitter is all that is needed to watch the TV.
Please refer to the illustration on page 2, whilst reading these
instructions.
Switching on/off
.To turn on the TV:
Press Mains ON/OFF switch ~.
To turn off the TV:
Press the Power ON/OFF button ~ on the remote control
transmitter, and the TV changes to the standby mode. During
the standby mode, the standby and power indicator illumi-
nates more brightly than during the power–ON mode.
Press this button to turn off the unit for short periods of the
time.
To turn on the TV from the standby mode:
Press one of these button.
T
Power ON/OFF ~
Programme Selector ~
(except buttons”1 -“ and “2-”)
L Programme Selector ~
TO cut off the mains power completely:
Press the Mains ON/OFF switch ~.
Important! Be sure to set the Mains ON/OFF switch O to the
off position, if the power failure occurs while view-
ing.
AUTO SHUT OFF
This TV set incorporates the AUTO SHUT OFF function.
Even if the TV is left on after you have gone to sleep, the
TV set changes to the standby mode within 10 minutes
after all broadcasts have ended.
Note: AUTO SHUT OFF also functions for the AV mode even
when there is no signal being transmitted.
The remaining time for AUTO SHUT OFF is displayed on
the screen.
Remaining time
c
&u
-10
Programme selection
e.g. TO select programme number 17, press “l-” button and
then press “7” button ~ within five seconds.
To select programme number 27, press “2-” button and
then press “7” button ~ within five seconds.
Picture and sound adjustments
(Use the remote control transmitter.)
To adjust the sound volume:
Press A (up) or Y (down)
volume ~button.
TO adjust the colour intensity:
Press @ (Colour) button.
+
Press A or ~ volume button.
To adjust the brightness:
Press ~i (Brightness) button.
+
Press A or ~ volume button.
TO adjust the picture cOtWaSt:
Press ~ (Contrast) button.
+
Press A or ~ volume button.
Fine tuning
Press <> (Fine tuning) button.
+
Press A or ~ volume button.
<>
1
I
Note: Normally fine tuning is not required for this TV. However,
in some case (such as radio interference) picture may bt=.
come more clear by detuning from the best tuned fre-
quency.
In such case, you can use this fine tuning to eliminate
some interference beat pattern.
To adjust the picture and sound by using the front controls of
the TV set:
Select the control function by pressing SELECT button ~.
I
*Each time SELECT button ~ is pressed, the control function
changes as follows;
~SOUND~ @ COLOUR
~-11. BRIGHT
~~C)NTRAST
Press Programme Selector O (+ or -), and adjust the
sound volume, colour, brightness or contrast.
TO scan the programmed:
Press the right side ( + ) of the programme selector ~ of the
TV set, and the TV set will step up to the next station, i.e; 1,2,
3...29, VCRI, VCR2, VCR3, 1,2,3 ...
Press the left side (–), and the TV set will step down to the
previous station.
–3–
(General Operation)
~ ....TV/AV Selector
To watch television programmes
leave this switch in the TV mode.
When this switch is set to the AV
mode you can enjoy the playback
from VCR or other AV equipment
connected to the AV input termi-
nals.
~.... Recall ~/S
Screen display
m
au
To display the on-screen indications, press this button.
The display disappears
after five seconds.
-;’”me
~
When this button is pressed ~1
for more than 2 seconds, a
menu display such as that
shown at the right will appear.
This menu display is used for
presetting of stations and
when setting special func-
tions.
~.... Memory O
PRESET + 1
SP-- + 2
Tv
+~
x
To return to the ordinary
lV mode, press Recall
button @ once again.
Present sound volume, colour, brightness and contrast levels
can be stored into the memory by pressing O (Memory) button
twice, and these control levels can be recalled by pressing Nor-
malization ~ button,
(first)
w
(second)
+ yellow
u
red
press MEMORY button once.
The “MEMO” display flashes in yellow.
Press MEMORY button again to
complete memorizing.
The “MEMO” display changes to red.
~ . Normalization +0+
When this button is pressed,
sound volume, colour, brightness
and contrast levels which are
NORMAL
memorized by pressing Memory
--- ++---
~ button are recalled.
~ .... Sound mute ~
Should you wish to mute the
sound (e.g. While talking on the
telephone), press this button once.
To switch the sound back on,
press it again.
@ .. ALT (Alternate)
Press the “ALT (Alternate)” button@ and the TV set will al-
ternately select the previous channel and the present chan-
nel. For example, now you are watching channel 4 but you
watched channel 2 previously. If you press the “ALT Key”,
channel 2 immediately appears.
@ .... Channel Scanning C“
Press Channel Scanning button @to search for a programme.
The channel positions are automatically scanned, and the chan-
nel scanning will stop at the position where it began. To stop at
the position you want, press this button again.
@ .... Off timer@
After a set time has elapsed, the power of the TV receiver is
switched off automatically.
Each time Off timer button @ is pressed, the set time
changes as follows:
“laid
30 minutes
60 minutes
~i
‘u-u
120 minutes
90 minutes
With the off timer being set and the channel display reset, the
remaining time is displayed by pressing the
off timer button
again.
When the button is pressed again within three seconds after
the button was first pressed in above manner, the time is set
to an upper time which is most close to the remaining time.
Just one minute before switching off, “-01” and programme
number you are watching are displayed on the screen.
The timer setting will be cancelled if the power is switched
off.
@ ... Headphone Jack ~
Inserting the headphone (option) to the outlet provides per-
sonal listening, (or recording purpose with the appropriate
lead.) The TV set speaker is automatically switched off.
–4–
S~ecial Functions
YOU can set the Special Functions to input the Special Codes.
The Special Codes and the Special Functions are as follows.
SPECIAL
CODE
SPECIAL FUNCTIONS
Re-set all Special Functions
00
(The start condition for the TV power is changed
to the standby start.)
01
Re-set all Special Functions
70 Search for the Channel Scanning
Memory Delete for the Channel Scanning
71 (Used to delete a programme position from the
channel scanning positions.)
Memory Add for the Channel Scanning
72 (Used to add a programme position to the channel
scanning positions.)
NOTE: Special functions are not cancelled when the power is
turned off or when the AC power plug is disconnected
from the mains.
Search for the Channel Scanning
(SPECIAL CODE “70)
When SPECIAL CODE “70 is input, all the programme posi-
tions are automatically scanned, and the active programme
positions are stored in memory.
Once this programming is completed, the TV receiver will se-
lect only the stored programme positions when Channel
Scanning key@ is pressed.
To input Special Code “70:
Press and hold ~/s (Recall) but-
ton O of the remote control trans-
mitterfor more than 2 seconds.
Press “2” button of the pro-
gramme selector ~ .
Press “7”
button of
tor ~
button, next press “O
the programme selec-
EI
PRESET + 1
SP-- + 2
Tv
+Q
1
sp--
n
SP70
Press O (Memory) button ~. The programme positions are
then automatically scanned, and the active programme po-
sitions are stored in the memory.
The channel scanning will then stop at the position where it
started scanning.
GI-GI-------------GJ
b“D”Eti
Search for the Channel Scanning is now completed.
Memory Delete for the Channel Scanning
(SPECIAL CODE “71”)
d
This function is used to delete a programme position from
the channel scanning positions, so it will not be scanned
when Channel Scanning button @is pressed.
For example, to delete position “3”
ning positions:
Select programme position “3”
using the Programme Selector O
or~.
Press and hold ~/S (Recall) but-
ton ~for more than 2 seconds.
Press “2” button of the pro-
gramme selector ~ .
Press “7”
button of
tor ~
button, next press “1”
the programme selec-
from the channel scan-
EI
3
n“
PRESET + 1
SP-- + 2
Tv
+D
I T==
I-2
El
SP71
Press O(Memory) button ~. (“SP 71” disappears.)
Position “3 is now deleted from the channel scanning posi-
tions.
Position “3 will be passed over when Channel Scanning but-
ton @is pressed.
delete
J
–5–
(Special Functions)
Memory Add for the Channel Scanning
(SPECIAL CODE “72”)
This function is used to add a programme position to the
channel scanning positions, so it will be scanned when
Channel Scanning button@ is pressed.
For example, to add position “3” to the channel scanning po-
sitions:
Ill Select programme position “3”
using the Programme Selector @
or=.
\
~ Press and hold ~/S (Recall) but-
= ton~ for more than 2 seconds.
Press 1’2” button of the pro-
gramme selector ~
Press “7” button, next press “2”
button of the programme selec-
‘.
tor ~ .
El
3
m
PRESET + 1
SP-- + 2
l-v
+a
D
sp--
1
SP72
Press O(Memory) button ~. (“SP 72” disappears.)
Position “3” is now added to the channel scanning positions.
_- Position “3” will be scanned when the Channel Scanning but-
ton @is pressed.
add
n“~+ltl~-”
Re-set All Special Functions
(SPECIAL CODE “01”)
When SPECIAL CODE “01” is input, all the special functions
are re-set.
To input Special Code “01”:
ill
El
131
El
Press and hold ~/s (Recall) but- ~1
ton Ofor more than 2 seconds.
H
Press “2” button of the pro-
gramme selector ~ .
sP--
Press “O” button, and then press
“l” button of the programme se-
lector ~ .
SPO1
L
I
Press O (Memory) button ~. (“SPOI” disappears.)
All the special functions are now re-set.
Re-set All Special Functions
[Special Code “00)
The Special Functions can also be cancelled by inputting
Special Code “00”.
Note: When Special Functions are cancelled using Special
Code “00”, the start condition for TV power is changed
to the standby start condition, meaning that the picture
will not appear even when the Mains ON/OFF Switch
O is set to the on position. To turn on the TV set from
the standby mode, press ~, O or ~ button.
Special Code “()()” is input in the same manner as Special
Code “01”.
I
‘-------X-------J
–6–
Automatically adjust for displays in English, German, Swedish, French and
TELETEXT USE ,ta,ianinaccordancewiththetelevision txoacicast signals.
REVEAL~–
INDEX ~—
TIME/SUB @
CANCEL ~–
Page Selection
TVl@
ALT
&
SIZE ~
TV/MIXITEXTO @ @
PAGE ALT @+@
HOLD ~
H Switching to the Teletext Mode
Press the TV/MIX/TEXT button, then the screen changes as
follows:
El”m”El
A ,,
*
II
Back to TV program me.
Page Selection
When teletext mode is first selected, the index page (p. 100)
is automatically obtained. The requested page is obtained
by simply pressing three number buttons in sequence. For
example, if you wish to look at page 151, pressing the num-
ber, (l), (5) and (1) in turn.
As each command is accepted, the page number at the left-
hand end of the header will be built up, digit by digit, until it
is complete.
After the final entry has been registered, rolling page num-
bers are presented until the requested page is received. As
soon as the two groups of numbers coincide, the informa-
tion contained on page 151 appears.
Other pages of the same service can be obtained in this
manner, using the appropriate number.
It is not necessary to go back to the index page each time;
within any one service you can change direct from one page to
another. After a new page has been entered, the previous page
is displayed until the new page is received. On reception of the
new page, the rolling page number stops, showing the re-
quested page number.
Note: If the new page is a NEWSFLASH or SUBTITLE page, the
television video is automatically turned on, and the
newsflash or subtitle is displayed in a box within the pic-
ture. Conversely, if the old paqe was a newsflash or sub-
title page, and ~ew page is ‘no;, then the picture is turned
off.
TELETEXT P1OO Wed 16 Aug 18:48:22
TELETEXT PIOO Wed 16 Aug 18:48:244:
‘P151 TELETEXT P144 Wed 16 Aug 18:48:271
VIEWING TV WHILE SEARCHING FOR A PAGE
In some cases it can take some time to look for a page. In the
interval you can view lV by pressing the CANCEL button.
When the page arrives, the page number will appear on the
normal TV picture. Press TV/MIXiTEXT button to display the
page.
Note: When you press the CANCEL button, the green “>”
mark is displayed at the top right of the screen. Whilst
this”> ‘r mark is displayed you can not select another TV
channel.
m
P351
P301
EEEl ;::i
/
EISEI
Sub-coded page access
For Teletext information which is longer than one page it
may take some time for the automatic changing of sub
pages to reach the sub page you require. It is possible, how-
ever, to enter the sub-page you require and then continue
watching the normal television picture until the correct sub-
page is reached.
A.
B.
c.
D.
E.
F.
Note:
Select the required page using the page selection
button.
Press the TIME/SUB button. The sub code digits ‘4----”
will be displayed in the top left of the screen.
Enter the desired sub-page number.
For example, if you select sub-page 10 you must press
O, 0, 1 and O button.
Press the CANCEL to return to normal television pro-
gramme.
When the correct sub-page is reached the page number
will appear on the normal television picture.
Press the TV/MIX/TEXT button to display the stored
page.
To clear the sub-coded page you must enter a new page
number, or the TIME/SUB button.
It is not possible to select another television station
during a sub-page access operation.
/’
‘-
–7–
(TELETEXT USE)
Page Alternate
m
Press the Page Alternate ~ button and the TV set will
alternately select the previous page and the present page.
For example, now you are watching “page 300” but you
watched “page 200” previously. If you press the Page Alter-
nate button, “page 200 appears.
r---=+l+
l----#L
Updated Pages
There are pages which are updated as events progress,
such as sports results, news reports and traffic information.
If you have selected one of the above pages from the list of
contents and you want to view television but still be kept
informed about the other events, press the CANCEL button.
The page will disappear and the TV station which will
broadcast this will appear in the screen. As soon as this
page is updated, the page number will appear on the nor-
mal TV picture. To display the updated page on the screen
press the TV/MIX/TEXT button. The page will disappear
when the CANCEL button is pressed again.
Note: It is not possible to select another TV station during
an UPDATE. You should first switch back to TV re-
ception by pressing the TVIMDQTEXT button. You
can, however, change both the picture and sound
settings.
CANCEL
Rzm
1
I
I
I
TV/MIX/TEXT
Some pages contain more information than can be dis-
played on the screen simultaneously and are therefore sub-
divided into a series of two or more sub-pages. The first
sub-page of a series of four sub-pages, for example, has the
indication 1/4 displayed at the top right of the screen (below
the time).
These sub-pages are ‘rotated’, that is, each sub-page is dis-
played for a certain time (determined by the broadcasting
authorities) before being replaced by the next sub-page. If it
is desired to halt this rotation and retains a particular sub-
page, the HOLD button should be pressed. The word HOLD
then appear on the top of the screen.
This command stops the reception of teletext data and can
be used to prevent the updating of pages whenever re-
quired.
Normal operation is restored by pressing the HOLD button
again or entering a new page number.
Large Characters (SIZE) ~
Normally small characters are used in teletext mode, but in
some circumstances the ‘doubleheight’ facility may be use-
ful; when the viewer is some distance from the receiver, for
example. Either the top or bottom half of the display can be
expanded by pressing the SIZE button. When this button is
pressed for the first time, the top half of the display is ex-
panded. If it is pressed once again, the bottom half of the
display is expanded.
To return the display to normal-sized characters, this button
should be pressed again.
If television mode is selected while large characters are be-
ing displayed, small characters will be displayed when the
system is next returned to teletext mode.
I 1
TEIETE)(T~ DISNAY
I 1 I
I
INDEX ~
When this button is pressed in teletext mode, several
teletext functions are reset: the page memory is cleared, the
command Time Page ON (T. PAGE) is cancelled, and the
teletext decoder is set up to display the index page (PIOO).
REVEAL s
Some pages have part of the display concealed: a quiz page
with concealed answers, for example. The command
REVEAL displays the concealed text as long as REVEAL but-
ton remains depressed.
t f 1 I
I
1
L
1
REVEAL
‘HOLD TELETEXT P173 Wed 16 Aug 10:56:05
1/4
–8–
(TELETEXT USE)
Video/Audio Input Connection
Time Coded Pages (TIMf?XUB) @
Time coding enables the viewer to put into store a specific
page of information ready for viewing at a pre-determined
time.
IMPORTANT NOTE
With present transmissions this facility is limited to the
‘Alarm Clock’ pages. Please refer to the transmitted index
for the appropriate page number.
The required page is selected in the usual manner and then
the command T. PAGE (Time Page On) is entered. The time
that the requested page should be received is then entered
on the screen using the number keys two digits for hours
and two digits for minutes, using the 24 hour clock system.
The character ‘T’ precedes the time digits to indicate that a
time code and not the actual code is being displayed, also
the four digits flash. After the time code has been entered
rolling page numbers are presented. The cancel button is
then pressed and the receiver reverts to picture. When the
pre-set time is reached the page number will appear in the
top left corner of the screen and the data can be seen by
pressing cancel again. To clear the time code from the T.V.
memory, press TIME/SUB ~ button again. (Time Page
off).
It
is important to remember that once the time coding has
been set and the text cancelled pressing any buttons on the
handset other than the Brightness, Colour, Volume and
Mute may upset the pre-set time.
TIME
If the time is required while a programme is being viewed
press the TIME/SUB @ button.
Providing that the channel being viewed is also transmitting
teletext, the time will appear at the top righthand of the sc-
reen for five seconds. The digits displayed represent hours/
minuteslseconds.
VIDEO/AUDIO Input level
f
Q(g e
VIDEO CAMERA
v-m
AUDIO-IN
AUDIO INPUT 436m Vrms More than 40 kfl
VIDEO DISC PLAYER
(AV TERMINAL)
Connect the video and audio outputs of a VTR, video disk
player, etc. to the input jack of this TV set. Tapes and discs
can be played back.
. TO watch the input picture, press TV/AV Selector ~.
To return to the TV mode, press TV/AV Selector ~ again.
Note: In the AV mode, you can select the TV programme. x
. For example, to select the programme position “7” in the AV
mode (while watching the play backing from a VTR):
Press “7” button of the program-
me selector ~.
D
raw
7
Programme number
Press TVIAV Selector o, and the
picture of the programme position
“7” will appear.
r
7
AV Connection to the Aerial
Socket
The A.V. apparatus can also be connected to the aerial socket
of your TV receiver. In this case, it is advisable to select tk
“VCRI “, “VCR2” or “VCR3” position for the best picture by–
pressing “O” key of the program me selector.
Each time “O” key is pressed, VCR Position changes as
follows:
F
VCR2
I
VCR3
Note: VCR Position is specially designed for the playback of the
AV equipments. The picture of the VCR play backing may
be distorted in other position.
For further details concerning this connection and adjust-
ment, refer to the operating instructions for the AV equip-
ment.
–9–
b’\
Pre-Settinq Of Stations Upto32broadcaststations inyourreception area can b~.tOt-d inthe electronic m,mO~Y.
n Press and hold ~ /s (Recall) button ~ for more than 2
~ Press O (Memory) button~.
m
~ Press “1” button of the programme selector ~ to select
~ Repeat steps~ tom for other desired channels.
the pre-set mode.
ProgrammE
position \
7
,,
fw~,
------------
~ Press the programme selector
programme position.
TVA9
ALT
&
29 VL
lrl/--------------
Channel
band
~ to select the desired
E
6 VL
I
-------------- .
~ Press BAND selector@ to select the channel band.
lb 1
6 VH
--------------
When BAND selector is pressed, the frequency will be set to the
Iowestfrequency in the set band.
Channel band VL, VH and U are for the following channel
groups.
VHF Range
VHF
LOW BAND: Channels I 3
VHF High BAND: Channels 4– If
UHF Range
UHF BAND:
Channels 21 69
The channel (VL, VH or U) Band is displayed on the screen.
~ Press and hold A or ~ (volume) button ~ until the desired
station appears.
[
] Press ~/s (Recall) button ~. This completes the pre-
!-
6 VH
ImnmmmI ------------
The
kmber of upright segments
increases for a higher-frequency
channel.
–lo–
setting.
&&-
L&l‘E
o
3
(q
<> 1~)
BAND
Q/s
“F’
1
6
Memory Copy
This TV tuning system has an-
other advanced feature called
“memory copy”.
For example, if you wish to copy the lV channel in the pro-
gramme position “2” into the programme position “6”:
1. Select the programme position “2”.
2. Press and hold ~ /s(Recall) button @ for more than 2 sec-
onds.
3. Press “l” button of the programme selector ~ to select
the pre-set mode.
4. Press “6” button of the program me selector ~ .
5. Press O (Memory) button ~.
6. Press
a/S (Recall) button ~.
S* o
Pati No. 4AA6P1oO491 -- E3RJ (A3 -B)
SANYO Electric Co., Ltd.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Sanyo CZP2141TX Manuale utente

Categoria
TV LCD
Tipo
Manuale utente

in altre lingue