Citizen Systems CBM1000II RF Manuale utente

User’s Manual

Mode d’emploi

Benutzerhandbuch

Manuale dell’utente

Manual del usuario

WARNING : This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

This printer conforms to the following Standards:

Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC,

92/31/EEC, 93/68/EEC.

LVD : EN60950

EMC : EN55022 Class A

EN61000-3-2

EN61000-3-3

EN55024

This declaration is applied only for 230V model.

Declaration of Conformity

CITIZEN is registered trade mark of CITIZEN WATCH CO., LTD., Japan

CITIZEN es una marca registrada de CITIZEN WATCH CO., LTD., Japón

IMPORTANT: This equipment generates, uses, and can radiate radio frequency

energy and if not installed and used in accordance with the instruction manual,

may cause interference to radio communications. It has been tested and found to

comply with the limits for a Class A computing device pursuant to Subpart J of

Part 15 of FCC Rules, which are designed to provide reasonable protection against

such interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, in which case the

user at his own expense will be required to take whatever measures may be

necessary to correct the interference.

CAUTION: Use shielded cable for this equipment.

Sicherheitshinweis

Die Steckdose zum Anschluß dieses Druckers muß nahe dem Grät angebracht und

leicht zugänglich sein.

For Uses in Canada

This digital apparatus does not exceed the class A limits for radio noise emissions

from digital apparatus, as set out in the radio interference regulations of the

Canadian department of communications.

Pour L’utilisateurs Canadiens

Cet appareil numérique ne dépasse pas les limites de carégorie a pour les

émissions de bruit radio émanant d’appareils numériques, tel que prévu dans les

réglements sur l’interférence radio du départment Canadien des communications.

— 1 —

ENGLISH

— 2 —

ENGLISH

1. GENERAL OUTLINE ............................................................................. 9

1.1 Features ..................................................................................................... 9

1.2 Unpacking ..................................................................................................9

2. BASIC SPECIFICATIONS .................................................................... 10

2.1 Model Classification ............................................................................... 10

2.2 Outer Appearance and Component Parts ............................................ 10

2.3 Basic Specifications ................................................................................11

2.4 Print Paper Specifications and Print Position ...................................... 12

2.5 Sensor Position and Cutter Position ..................................................... 13

3. OPERATION ........................................................................................ 14

3.1 Connecting the AC Adapter and AC Power Cord ................................ 14

3.2 Connecting Interface Cables .................................................................. 14

3.3 Connecting the Drawer Kick-Out Connector ........................................15

3.4 Setting/Replacing Paper Rolls ...............................................................16

3.5 Adjusting the Paper Near-End Sensor .................................................. 16

3.6 Using 58 mm Wide Paper Rolls .............................................................17

3.7 Removing Jammed Paper ..................................................................... 17

3.8 Cleaning the Print Head ......................................................................... 17

3.9 Operation Panel and Error Indication ................................................... 18

3.10 Self-printing........................................................................................... 20

3.11 Hexadecimal Dump .............................................................................. 20

3.12 Printer Buffer ......................................................................................... 21

3.13 Device ID ................................................................................................ 21

4. SETTING DIP SWITCHES ................................................................... 22

4.1 Location of DIP Switches ....................................................................... 22

4.2 Table for Setting DIP Switches .............................................................. 22

5. MAINTENANCE AND SERVICE ......................................................... 24

APPENDIX 1. OUTLINE DRAWING .......................................................... i

APPENDIX 2. BLOCK DIAGRAM .............................................................. i

APPENDIX 3. IDENTIFICATION OF SEND STATUS ............................... ii

APPENDIX 4. PARALLEL INTERFACE .................................................... iii

APPENDIX 5. SERIAL INTERFACE .......................................................... v

APPENDIX 6. CONTROL COMMAND ................................................... vii

THE TABLE OF CONTENTS

— 3 —

ENGLISH

GENERAL PRECAUTIONS

1 The information contained herein is subject to change without prior notice.

without written permission from CITIZEN SYSTEMS.

3 Except explained elsewhere in this manual, do not attempt to service,

disassemble or repair this product by yourself.

4 Note that CITIZEN SYSTEMS shall not be responsible for any damage

attributable to incorrect operation/handling or improper operating

environments which are not specified in this manual.

5 Operate this printer only as described in this manual. Failure to do so may

cause accidents or other problems.

6 Data are basically for temporary use, not stored for a long period or

permanently. Please note that CITIZEN SYSTEMS is not responsible for any

damage or lost profit resulting from the loss of data caused by accidents,

repairs, tests, or any other occurrence.

7 If you have any question or comment regarding the information contained

in this manual, please contact your CITIZEN SYSTEMS dealer.

8 Please note CITIZEN SYSTEMS is not responsible for anything that may

occur from operating this printer regardless of what is stated in “7” above.

— 4 —

ENGLISH

SAFETY PRECAUTIONS

Before using this product for the first time, carefully read these SAFETY

PRECAUTIONS. Incorrect operation may result in unexpected accidents (fire,

shock, or injury).

● After having read this Manual, keep it in a safe, readily-accessible place for future

reference.

● Some of the descriptions contained in this manual may not be relevant to some

printer models.

In order to prevent injury hazard to operators, third parties or damage to

property, special warning symbols are used in this user’s manual to indicate

important items to be strictly observed.

● The following describes the degree of hazard and damage that could occur if the

printer is improperly operated by ignoring the instructions indicated by the

warning symbols.

WARNING

Neglecting precautions indicated by this symbol may result in fatal or serious

injury.

CAUTION

Neglecting precautions indicated by this symbol may result in injury or

damage to properties.

This symbol is used to alert your attention to important items.

This symbol is used to indicate prohibited actions.

This symbol is used to alert you to the danger of electric shock or

electrostatic damage.

This symbol denotes a request to unplug the printer from the wall

outlet.

— 5 —

ENGLISH

Caution Labels

WARNING

• Do not attempt to insert any plug (e.g. modular plug) other

than the specified drawer kick-out connector plug into the

drawer kick-out connector as it may damage the telephone

connection or the printer.

CAUTION

• The thermal head remains at a dangerously high

temperature immediately after use. Do not touch the head

until it cools off.

WARNING

Do not use or store this product in a place where it will be exposed to:

• Flames or moist air

• Direct sunlight

• Hot airflow or radiation from a heating device

• Ill-ventilated atmosphere

• Chemical reactions in a laboratory

• Airborne oil, steel particles, or dust

• Salty air or corrosive gases

• Static electricity or strong magnetic fields

● Neglecting these warnings may result in printer failure,

overheating, emission of smoke, fire, or electric shock.

Do not drop any foreign object nor spill liquid into the printer. Do not

place any object on the printer either.

• Do not drop any metallic object such as a paper clip, pin or screw into

the printer.

• Do not place a flower base, pot or cup containing water on the

printer.

• Do not spill coffee, soft drinks or any other liquid into the printer.

• Do not spray insecticide or any other chemical liquid over the

printer.

● A metallic foreign object, if accidentally dropped into the printer,

may cause printer failure, fire, or electric shock. Should it occur,

immediately turn the printer off, unplug it from the supply outlet,

and call your local CITIZEN SYSTEMS dealer.

— 6 —

ENGLISH

Please observe the following precautions for power source and power cord:

• Do not plug or unplug the power cord with a wet hand.

• Use the printer only at the specified supply voltage and

frequency.

• Use only the specified AC adapter with the printer.

• Check to make sure that the supply outlet from which the

printer is powered has a sufficient capacity.

• Do not plug the power cord into a supply outlet with dust or debris left

on its plug.

• Do not supply the printer from a power strip or current tap shared with

other appliances.

• Do not use a deformed or damaged power cord.

● Neglecting to handle properly may result in printer failure,

emission of smoke, fire, or electric shock.

● An overload may cause the power cable to overheat or the circuit

breaker to trip.

• Do not allow anything to rest on the power cord. Do not place the

printer where the power cord will be trampled on.

• Do not attempt to modify the power cord unnecessarily.

• Do not use or carry the printer with its power cord bent, twisted, or

pulled.

• Do not lay the power cord in the neighbor of a heating device.

● Neglecting these cautions may cause wires or insulation to break, which

could result in leakage, electric shock, or printer failure. If a power cord

sustains damage contact your CITIZEN SYSTEMS dealer.

• Supply power to the printer from a convenient wall outlet,

readily accessible in an emergency.

• Do not leave things around the supply outlet to always

ensure easy access to it.

● The printer may not be immediately shut down in an

emergency.

• Insert the power plug fully into the outlet.

• If the printer is not to be used for a long time period, leave it

disconnected from its supply outlet.

Do not handle the printer in the following ways:

• Do not allow the printer to sustain strong impacts or hard jolts (e.g.

trampling, dropping, striking with a hard edge).

• Never attempt to disassemble or modify the printer.

• Do not clean the printer with any organic solvent, such as

alcohol, paint thinner, trichloroethylene, benzene, or keton.

● Neglecting to handle properly may result in printer

failure, overheating, emission of smoke, fire, or electric

shock.

Install, use, or store the printer out of the reach of children.

● The plastic bag the printer came in must be disposed of properly or kept

away from children. Wearing it over the head may lead to suffocation.

● Electric appliances could cause an unexpected injury or accident if they

are handled or used improperly.

● Keep the power cord and signal cables out of the reach of children. Also

children should not be allowed to gain access to any internal part of the

printer.

Benzine

Thinner

— 7 —

ENGLISH

CAUTION

Place the printer on a flat surface.

● Otherwise it may drop off from its position.

Be careful where you place the printer and what is placed near it.

• Take care that a nearby wall or some kind of cloth does not block

printer ventilation holes.

• Do not use the printer with any object placed on it.

● Be careful about internal heat buildup, which could cause fire and

deform the case.

• Avoid using the printer near a radio or TV set or from supplying it

from the same outlet as these appliances.

• For interconnections, use shielded or a twisted pair of cables and

ferrite cores, or other anti-noise devices.

• Avoid using the printer with a device that is a strong source of noise.

● The printer may have an adverse effect on nearby radio or TV

transmissions. There may also be cases when nearby electrical

appliances adversely influence the printer, causing data errors or

malfunction.

Use the printer with its grounding post connected to a convenient

grounding facility.

● If leakage occurs electric shock may result.

Do not connect the printer’s grounding post to any of the following

facilities:

• Utility gas piping

● A gas explosion could result

• Telephone line ground

• Lightning rod

● If lightening strikes a large surge of current may cause fire or

shock

• Utility water pipes

● Plastic water pipes should not be used for grounding. (Those

approved by a Waterworks Department may be used.)

Before connecting or disconnecting the grounding lead to or from the

printer, always unplug it from supply outlet.

Before connecting or disconnecting the power cord or interconnect

cables to or from the printer, always turn the entire system power off.

When disconnecting a cable, do not pull out by the cable. Always hold

the plug.

Firmly insert the cable plug into its mating socket.

● A cross connection may damage the printer’s internal electronics

or the host system’s hardware.

Only use the printer with devices that have designated solenoid

specifications for the drawer kick-out connector.

● Neglecting this caution may result in malfunction or failure.

— 8 —

ENGLISH

Observe the following precautions for daily maintenance:

• When cleaning the printer, always turn it off and unplug it from the

supply outlet.

• Use a soft, dry cloth for cleaning the surface of the printer case.

• For severe stains, use a soft cloth slightly dampened with water.

• Never use organic cleaning solvent such as alcohol, paint thinner, or

benzen.

• Never use a chemically processed cleaning cloth.

• To remove paper chips, use a soft brush.

• When transporting the printer, remove the roll paper from its paper

holder.

• When cleaning the thermal head surface, use a cotton gauze slightly dampened

with alcohol.

To prevent possible malfunction or failure observe the following:

• Avoid operating the printer without roll paper properly loaded or

with paper not complying with specifications.

● May damage thermal head or result in poor print quality.

• Avoid using torn pieces of paper or spliced with plastic adhesive

tapes.

• Avoid forcibly pulling already loaded paper by hand.

• Avoid wedging the paper in by the printer cover.

● May jam paper. To release, refer to “Removing Jammed Paper”

in this manual.

• Avoid using a sharp pointed device to operate panel keys.

● Neglecting these cautions may result in printer malfunction or

failure.

To prevent injury and printer failures from worsening, observe the

following:

• In case of trouble do not attempt to repair the printer.

Leave it to our service engineer.

• Do not touch the printing surface of the thermal head.

• Be careful that the printer cover does not entrap your hands or

fingers.

• Be careful with sharp edges on the printer. Don’t allow them to injure

you or damage property.

• Do not touch any of the moving parts (e.g. paper cutter, gears, active

electrical parts) while the printer is working.

● May result in electric shock, burn, or injury.

● If the printer emits smoke, an odd smell, or unusual noise while

printing, immediately abort the current print session and unplug

the printer from the supply outlet.

Benzine

Thinner

DAILY MAINTENANCE

CAUTION

• Do not touch the thermal head’s printing surface with bare hand or a metallic

implement.

• The thermal head is at a dangerously high temperature immediately after printing.

Allow it to cool off before launching maintenance work.

— 9 —

ENGLISH

1. GENERAL OUTLINE

The CBM1000 Type II is a compact thermal line printer designed for use with a broad

array of terminal equipment including data, POS, and kitchen terminals.

With extensive features, it can be used in a wide range of applications.

To obtain the best results from the CBM 1000 Type II printer, please read the

instructions this manual thoroughly.

1.1 Features

● Paper drop-in mechanism. Supply/replace paper rolls by simply dropping a paper

roll into the printer and closing the cover. Greatly facilitates paper handling and

head cleaning.

● Ease of paper threading and head cleaning.

● High speed (150 mm/s), and low-noise thermal printing.

● Front-side paper ejection method. Allows printer installation and use anywhere

with few restrictions.

● Hermetic covering structure. Protects foreign matter or liquid from entering the

printer.

● Built-in input buffer.

● Barcode Printing. Made possible using special commands.

● Page mode. Now you can arrange pages freely.

● Registration of user-defined characters and logos into flash memory.

● Built-in drawer kick-out interface.

● Auto cutter mechanism provided as a standard unit.

● Two types of power supply. Select between an easy-to-handle, built-in power

supply type and lightweight flat AC adapter type.

● Can use 58 mm wide paper rolls by employing the supplied partition.

1.2 Unpacking

When unpacking the printer, confirm that the following are provided:

Printer

Sample paper roll

Partition

AC adapter

(provided with the A type only)

AC power cord

(not supplied with Type D)

User’s manual

CAUTION

• Do not use the printer in an environment where condensation can occur. If condensation

forms, leave the power off until it completely evaporates.

— 10 —

ENGLISH

Label paper function

no display: Nothing

L: Label interval detection

2. BASIC SPECIFICATIONS

2.1 Model Classification

The printer models are classified by the following designation method:

CBM1000 II R F 120 S - L

Power supply

S: Standard type

(Power supply built-in)

A: AC adapter type

D: Without AC adapter

Attached power cord specification

120: For AC 120 V

230: For AC 230 V

024: Without AC adapter

Character Set

F: International

Interface

R: Serial (RS-232C)

P: Parallel

(IEEE 1284 compliant)

*Dedicated adapter type and power cord:

31AD-U (AC 120 V 3-wire cord)

31AD-E (AC 230 V Class I cord)

Model Name

2.2 Outer Appearance and Component Parts

CBM1000II S CBM1000II A/CBM1000II D

Printer cover

Ejector

Top cover

Power box

Power switch

POWER lamp

ERROR lamp

FEED switch

Drawer kick-out connector

Grounding terminal

Inlet

Printer cover

Ejector

Top cover

Power switch

Drawer kick-out

connector

Grounding terminal

Power connector

Interface connector

POWER lamp

ERROR lamp

FEED switch

— 11 —

ENGLISH

Line thermal dot print method

2.3 Basic Specifications

Print method

CBM1000II RF024D

CBM1000II PF024DItem

Model CBM1000II RF230S/A

CBM1000II PF230S/A

CBM1000II RF120S/A

CBM1000II PF120S/A

—

UL, C-UL, FCC Class A TÜV, GS, CE marking UL, C-UL, FCC Class A,

TÜV, GS, CE marking

*

1

Represents the value when a 58 mm wide paper roll is used (User selectable).

*

2

The number of printable columns is selectable with a DIP switch.

*

3

Represents the safety standards acquired when CITIZEN SYSTEMS-made adapters (31AD series) are used.

72 mm/576 dots, (54 mm/432 dots)*

1

8 × 8 dots/mm (203 dpi)

150 mm/sec (Fastest, print density standard level), (1,200 dot lines/sec)

Font A: 48/42 (36/30)*

1

columns (12 × 24)

Font B: 64/56 (48/40)*

1

columns (9 × 24)

Font A: 1.25 × 3.00 mm; Font B: 0.88 × 3.00 mm

Alphanumeric characters, International characters, Code pages PC437,

Katakana, PC850, PC860, PC863, PC865, PC852, PC866, PC857, and Windows

code page

Capable of registering user-defined characters and logos into flash memory.

UPC-A/E, JAN (EAN) 13/8 columns, ITF CODE 39, CODE 128, CODABAR,

CODE 93

Serial (RS-232C), Parallel (IEEE1284 compliant, Bi-directional communication)

Thermal paper roll: 80 mm (58 mm) × ø 83 mm

Thermal Label paper roll : 80 mm (58 mm) × ø 83 mm

(See “ Print Paper Specifications”.)

Selects the L-Spec. (factory option)

4.23 mm (1/6 inches), selectable using commands

4K bytes (72 bytes selectable with a DIP switch)

S type: AC 120/230 V ±10%; A type/D type: DC 24 V ±7%

Approx. 100 W

Rated input: AC 120 to 240 V, 50/60 Hz, 120 VA

Rated output: DC 24 V, 1.9 A (Peak 3.5A)

S type: Approx. 2.0 Kg; A type/D type: Approx. 1.4 Kg

S type: 145 (W) × 190 (D) × 157 (H) mm

A type/D type: 145 (W) × 190 (D) × 114 (H) mm

5 to 40°C, 35 to 85% RH (No condensation)

Print head life: Pulse resistance 1 × 10

8

pulses (Print ratio 12.5%)

Wear resistance 100 Km (At normal temperature/humidity

with recommended paper used)

Auto cutter life: 1,000,000 times of cutting (At normal temperature/

humidity with recommended paper used)

31 AD-U 31 AD-E

Reliability

Print width

Dot density

Print speed

Number of print

columns*

2

Character size

Character type code

page

Logo registration/print

Types of bar code

Interfacing

Paper roll

Label detection

Line spacing

Input buffer

Supply voltage

Power consumption

AC adapter specification

Weight

Outside dimensions

Operating temperature

and humidity

Storage temperature and

humidity

Type

–20 to 60°C, 10 to 90% RH (No condensation)

Safety Standard*

3

— 12 —

ENGLISH

4

25

4422

(1) Thermal Paper roll

Maximum print area 72

Paper width 80 +0/-1

Maximum print area 54

Paper width 58

2.4 Print Paper Specifications and Print Position

Printing surface

ø83 or less

(Recommended papers)

TF50KS-E2D from Nippon Paper

KP50 from Shin-Ohji Paper

F230AA or HP220A from Mitsubishi

Paper or equivalent

(2) Thermal label sheet (label gap detection) * Only L-Spec.

Base sheet width: 58 +0/-1

Maximum print area 72

Maximum print area 50

Minimum label gap

Unit: mm

ø12

60~80 µm

ø18

ø25~28

65~85 µm

Max. label width: 54

Max. label width: 76

Base sheet width: 80 +0/-1

Minimum label length

Approx. 2

ø83 or less

Printing surface

60 µm or less

(Recommended papers)

KPT86S/G63BC P22 from Ohji Tac.

or equivalent

CAUTION

• A roll paper not complying with the specifications may cause some departure in print tone.

Adjust print tone with the DIP switch (see “Setting DIP Switches”).

• Do not paste paper end to the core as it may cause coloration or faint letters if printed

documents are exposed to a particular chemical or oil afterwards.

• Rubbing the document surface with your nail or metallic device may cause coloration.

• Coloration occurs at a temperature of around 70°C or above. Keep documents away from

heat, moisture, or light.

Unit: mm

— 13 —

ENGLISH

(11mm) (40mm)

2.5 Sensor Position and Cutter Position

Manual cutting

position

Auto cutting position

Top print line

Paper feed direction

CAUTION

• Observe the following rules on the auto cutter usage:

• Every cut paper should be no less than 10 mm in length. Thin paper strips can cause

paper to jam.

• When cutting a label roll, be sure to cut the base sheet. Never cut labels (tags).

Approx. 27

Approx. 13

Approx. 17

Label gap sensor

Unit: mm

Paper end sensor

— 14 —

ENGLISH

3. OPERATION

3.1 Connecting the AC Adapter and AC Power Cord

1 Turn off the power of the printer.

2 For the AC adapter type only: With the flat side of the AC adapter’s cable connector

facing upward, insert the cable connector into the power connector on the back side of

the printer.

3 Connect the AC power cord to the inlet of the printer, and insert the AC power-cord

plug into a suitable wall outlet.

Power connector pin configuration

No.

1

2

3

SHELL

Function

+24

GND

N.C

F. G

Standard type

Inlet

AC power cord

Power connector

Flat side

Cable connector

1 Turn off the power of the printer. (As well as the connected host computer.)

2 Orient the interface cable terminal correctly and insert it into the interface connector.

3 Secure the cable terminal as shown below.

Serial interface cable: Fasten the connector with screws.

Parallel interface cable: Hold the connector with clamps.

4 Connect the other end of the interface cable to the host computer.

3.2 Connecting Interface Cables

Serial interface cable

Serial interface connector Parallel interface connector

AC adapter type

Inlet

AC adapter

AC adapter cord

1

3

2

Connector used:

TCS7960-53-2010 (Hosiden) or

equivalent

Applicable connector:

TCP8927-63-1100 (Hosiden) or

equivalent

TCP8927-53-1100 (Hosiden) or

equivalent

Clamps

Parallel interface cable

— 15 —

ENGLISH

61

1

2

3

4

5

6

FG

DRAWER 1

DRSW

VDR

DRAWER 2

GND

CAUTION

• Do not connect any other device than the specified drawer (Solenoid) to the drawer kick-out

connector. (Do not connect a telephone line either.)

1 Turn off the power of the printer.

2 Orient the drawer kick-out cable connector

correctly, insert it into the drawer kick-out

connector on the back of the printer.

3 Fasten the ground wire to the ground

connector on the printer with a screw.

3.3 Connecting the Drawer Kick-Out Connector

Drawer kick-out connector

Ground wire

Drawer kick-out cable

connector

Connector used:

TM5RJ3-66 (Hirose) or

equivalent

Applicable connector:

TM3P-66P (Hirose) or

equivalent

CAUTION

• No output is produced while printing.

• The drawers 1 and 2 cannot be driven simultaneously.

• A solenoid used for the drawer should be of 24 Ω or more. The output current should be

kept at 1 A or less; otherwise, breakdown or burning could occur.

(2) Electrical characteristics

1) Driving voltage: 24 VDC

2) Driving current: Approx. 1 A max. (shall not exceed 510 ms.)

3) DRSW signal: Signal levels: “L”=0 to 0.5 V, “H”=3 to 5 V

(3) DRSW signal

DRSW signal status can be tested with the DLE+EOT, GS+a, or GS+r command or at pin 34

on the parallel interface port.

(4) Drive Circuit

(1) Connector Pin Configuration

VDR

1

2

3

4

5

6

VDR

Function

Frame Ground

Drawer 1 drive signal

Drawer switch input

Drawer drive power supply

Drawer 2 drive signal

Common ground on circuits

No. Signal

— 16 —

ENGLISH

CAUTION

• Always use the specified types of paper roll.

• Use of other types of paper roll may not be able to guarantee the specified print quality or

service life of the printer.

• When opening the printer cover, do not apply an excess force to it beyond its stop position.

• The print head becomes hot immediately after printing. Do not touch it with your hand.

During printing, do not open the printer cover. Do not hold the end of the paper as it prints

and ejects. Doing so may cause the paper to jam.

4321

1 Turn on the printer.

2 Push the ejector in the direction shown to

unlock the printer cover.

3 Placing your hands on both sides of the

printer cover, open it until it comes to a

stop.

4 Check the winding direction of the paper

roll, and then place it into the paper roll

holder correctly.

5 With the end of the paper approx. 5 cm out

of the case of the printer, close the printer

cover. Push lightly on the printer cover

until a “click” is heard.

6 Remove an excess length of paper with

the tear bar. (Manual cutter)

3.4 Setting/Replacing Paper Rolls

Tear bar

1 Open the printer cover.

2 Push the sensor knob in the direction of

arrow 1 to disengage its claw (Or unlock

the sensor unit), and then adjust the

sensor unit to a desired paper remaining

position within the range shown by arrow

2.

3 The following table shows the relationship

between adjustment positions and levels

of paper roll remaining. (A rough guide)

3.5 Adjusting the Paper Near-End Sensor

Arrow 1

Arrow 2

Sensor unit

* When specified paper rolls are used.

CAUTION

• Use the level of paper remaining (Paper-roll outside diameter) just as a guide as it varies

depending on the particular printer and paper rolls used.

Printer cover

Print head

Paper roll

Ejector

Sensor knob

Adjustment

position

Adjustment

position

1

2

3

4

Level of paper remaining

(Paper roll outside diameter/mm)

ø

18

ø

21

ø

24

ø

27

— 17 —

ENGLISH

1 Turn off the power of the printer.

2 Open the printer cover.

3 Take off two screws and remove printer

cover.

4 Take off damper retention screws,

reposition damper (11 mm) in the direction

of the arrow, then secure it with the

original screws again.

5 Replace printer cover on printer.

6 Install the supplied partition into the

position as illustrated.

7 Change DIP switch setting for 58 mm roll

paper, by referring to “SETTING DIP

SWITCHES”.

3.6 Using 58 mm Wide Paper Rolls

CAUTION

• Do not change DIP switch setting from 58 mm

into 80 mm roll paper in the middle of printing.

1 Open the printer cover.

2 Wipe off stains, such as dust and the like, on the heating element of the head using a

cotton swab soaked in ethyl alcohol.

3.8 Cleaning the Print Head

1 Turn off the power of the printer.

2 Open the printer cover.

3 Remove the paper jam including any paper chips remaining. (Also take out the paper

roll from the holder.)

4 Close the printer cover.

5 Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared.

3.7 Removing Jammed Paper

CAUTION

• The print head becomes hot immediately after printing. Do not touch it with your hand. Do

not touch the heating element of the head with a bare hand or metal object either.

CAUTION

• The print head becomes hot immediately after printing. Do not touch it with your hand. Do

not touch the heating element of the head with a bare hand or metal object either.

Printer cover

Damper

Partition

La pagina sta caricando ...

Citizen Systems CBM1000II RF Manuale utente

Questo manuale è adatto anche per

Citizen Systems CBM1000II RF Manuale utente

in altre lingue

Documenti correlati

Altri documenti