Yamaha RX-V800RDS Manuale utente

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia ID

V624940

RX-V800RDS

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

G B

RX-V800RDS

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

0100V800RDS(GB)-cv1/4 8/29/0, 10:02 AM1

II

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

right and left, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause

electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation.

If the temperature inside this unit rises, it may

cause fire, damage to this unit, and/or personal

injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical

storm.

14 Take care of this unit so that no foreign objects and/

or liquid drops inside this unit.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

CAUTION

1

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTENTS

INTRODUCTION

CONTENTS ........................................................... 1

FEATURES ............................................................ 2

GETTING STARTED ........................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS ........................ 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Description of the Numeric Buttons......................... 7

Using the Remote Control ........................................ 8

Front Panel Display .................................................. 9

Rear Panel .............................................................. 10

PREPARATION

SPEAKER SETUP .............................................. 11

Speakers to Be Used ............................................... 11

Speaker Placement ................................................. 11

CONNECTIONS ................................................. 12

Before Connecting Components ............................ 12

Connecting Audio Components ............................. 12

Connecting Video Components .............................. 14

Connecting the Speakers ........................................ 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ............................ 18

IMPEDANCE SELECTOR Switch ....................... 19

Connecting the Power Supply Cords ...................... 19

ON-SCREEN DISPLAY (OSD) ......................... 20

OSD Modes ............................................................ 20

Selecting the OSD Mode ........................................ 20

SPEAKER MODE SETTINGS ......................... 21

Summary of SPEAKER SET Items

1A through 1E .................................................... 21

ADJUSTING THE SPEAKER

OUTPUT LEVELS ......................................... 22

Before You Begin ................................................... 22

Using the Test Tone (TEST DOLBY SUR.) .......... 22

BASIC OPERATION

BASIC PLAYBACK ............................................ 24

Input Modes and Indications .................................. 26

Selecting a Sound Field Program ........................... 28

Normal Stereo Reproduction .................................. 29

TUNING ............................................................... 30

Connecting the Antennas ........................................ 30

Automatic (or Manual) Tuning .............................. 31

Presetting Stations .................................................. 32

Tuning in to a Preset Station .................................. 33

Exchanging Preset Stations .................................... 34

RECEIVING RDS STATIONS .......................... 35

Description of RDS Data ........................................ 35

Changing the RDS Mode ....................................... 35

PTY SEEK Function .............................................. 36

EON Function ........................................................ 37

BASIC RECORDING ......................................... 38

ADVANCED OPERATION

SET MENU .......................................................... 39

Adjusting the Items on the SET MENU................. 39

1 SPEAKER SET (speaker mode settings) ........... 40

2 LOW FRQ TEST ............................................... 42

3 L/R BALANCE (balance of the

left and right main speakers) .............................. 43

4 HP TONE CTRL (headphone tone control) ....... 43

5 CENTER GEQ (center graphic equalizer) ......... 43

6 INPUT RENAME .............................................. 44

7 I/O ASSIGNMENT ............................................ 44

8 INPUT MODE (initial input mode) ................... 44

9 PARAM. INI (parameter initialization) ............. 44

10 DOLBY D. SET (Dolby Digital set) ............... 45

11 DTS LFE LEVEL ............................................ 45

12 6.1/ES AUTO ................................................... 45

13 SP DELAY TIME ............................................ 46

14 DISPLAY SET ................................................. 46

15 MEMORY GUARD ......................................... 46

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ...................................................... 47

SLEEP TIMER .................................................... 48

Setting the Sleep Timer .......................................... 48

Canceling the Sleep Timer ..................................... 48

REMOTE CONTROL FEATURES .................. 49

Selector Dial ........................................................... 49

Commonly Used Buttons in Any Position of the

Selector Dial ....................................................... 50

Controlling the Components

Connected to This Unit ...................................... 50

Button Names and Functions in Each Position ...... 51

Setting the Manufacturer Code .............................. 54

Programming a New Remote Control Function

(Learn Feature) ................................................... 55

Returning to the Factory Setting ............................ 56

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM ............................. 57

Hi-Fi DSP Programs ............................................... 57

CINEMA DSP Programs ....................................... 58

MOVIE THEATER Programs ................................ 61

SOUND FIELD PROGRAM PARAMETER

EDITING ......................................................... 62

What is a sound field? ............................................ 62

Sound Field Program Parameters ........................... 62

Changing Parameter Settings ................................. 63

Resetting a Parameter to the Factory-set Value ...... 63

Digital Sound Field Parameter Descriptions .......... 64

APPENDIX

TROUBLESHOOTING ...................................... 68

SPECIFICATIONS ............................................. 73

2

Thank you for selecting this YAMAHA AV receiver.

FEATURES

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 15 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

Built-in 5-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz)

Main: 100 W + 100 W (8 Ω)

Center: 100 W (8 Ω)

Rear: 100 W + 100 W (8 Ω)

Multi-Mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder

◆ DTS/DTS ES Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

◆ Multi-Functions for RDS Broadcast Reception

Manufactured under license from Dolby Laboratories.

“Dolby”, “AC-3”, “Pro Logic”, “Surround EX” and the double-D

symbol are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround” and “DTS ES” are

3

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Remote control

Installing Batteries in the Remote

Control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

■ Notes on batteries

• Change the batteries periodically.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Manganese batteries (4)

(AAA, R03, UM-4)

Indoor FM antenna

AM loop antenna

Quick Reference Card

■ Changing batteries

As the batteries lose power, the operating range of the

remote control decreases and the indicator does not flash

or its light becomes dim. When you notice any of these

conditions, change all of the batteries.

If the remote control is without batteries for more than

2 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

Note

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

1

2

3

A/B/C/D/E

Quick Reference Card

75-ohm/300-ohm

antenna adapter

(U.K. model only)

4

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit (see page 9).

4 INPUT MODE

Selects the mode of input for sources that send two or

more types of signals to this unit (see page 26).

You cannot control the input mode when you select 6CH

INPUT as the input source.

5 INPUT l / h

Selects the input source (DVD, D-TV/LD, CBL/SAT,

VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,

CD-R, MD/TAPE) you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH INPUT takes

priority over the source selected with INPUT l / h (or

the input selector buttons).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel.

9 BASS EXTENSION ON/OFF

When pushed in (ON), this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

However, this boost may not be noticeable if “1B MAIN

SP” on the SET MENU is set to SMALL and “1D LFE/

BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT ON/OFF

When pushed in (ON), BASS, TREBLE, and BASS

EXTENSION are bypassed, eliminating any alteration of

the original signal.

A/B/C/D/E

SPEAKERS

STANDBY

/ON

AB

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET/

TUNING

BASS

6CH INPUT

VOLUME

INPUT

INPUT MODE

–

+

TREBLE

–

+

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

RDS MODE

/FREQ

EON PTY SEEK

MODE

START

FM/AM

PHONES S VIDEO VIDEO

L AUDIO R OPTICAL

SILENT

VIDEO AUX

EFFECT

PROGRAM

ON OFF

SURROUND

DIGITAL

TUNER

DSP

1

2

34

56

7

89 0

qw

e

r

ty

h

g

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

RDS MODE

/FREQ

EON PTY SEEK

MODE

START

FM/AM

iopa

sdf

u

5

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

a RDS MODE/FREQ

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

services) and/or frequency display mode in turn.

s EON

Press this button to select the desired program type

(NEWS, INFO, AFFAIRS, SPORT) when you want to

tune in to a radio program of that type automatically.

d PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

f PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

g BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

h TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the left and

right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front

panel door, close the door.

D

I

G

I

T

A

L

q EFFECT

Switches the effect speakers (center and rear) on and off.

If you turn off the output of these speakers by using

EFFECT, all Dolby Digital and DTS audio signals except

for the LFE channel are directed to the main left and right

channels.

When Dolby Digital or DTS signals are mixed, the left

and right main channel signal levels may not match.

w A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

e PROGRAM l / h

Selects the DSP program (see page 28).

r PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

t PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

y VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

u PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset

station number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

i FM/AM

Switches the reception band between FM and AM.

o MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

p TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

To open, press gently on the lower part of the panel.

6

CONTROLS AND FUNCTIONS

A/B/C/D/E

TV INPUT

TV VOLUME

TV POWER

EFFECT

w

e

1

2

3

4

5

6

7

8

0

q

9

r

t

y

u

i

Remote Control

This section describes the basic operation of this unit with

the remote control. First, set the selector dial to the AMP/

TUN position. See “REMOTE CONTROL FEATURES”

on pages 49 to 56 for full details.

Select the

AMP/TUN

position.

See page 7.

1 DSP

Switches the function of the numeric buttons to the DSP

program selector (see page 7).

2 Indicator window

Shows the name of components which can be controlled.

3 Numeric buttons (Input selector buttons)

These buttons select the input source.

See pages 7 and 8 for the numeric buttons.

4 TEST

Outputs the test tone.

5 ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

6 j / i

Adjust DSP program parameters and SET MENU items.

7 LEVEL

Selects the effect speaker channel (center, rear and

subwoofer) so you can adjust their output level

independently.

8 SLEEP

Sets the sleep timer.

9 INPUT

Switches the function of the numeric buttons to the input

selector (see page 7).

0 Indicator

Flashes while the remote control is sending signals.

q Selector dial

Turn this dial to select the position for the component to

be controlled. (The proper code must be set up for your

component. See “Setting the Manufacture Codes” on

page 54.) When the position is selected, the remote

control is set to that component operation mode.

w A/B/C/D/E, PRESET–/+

These buttons are used to select a preset station.

A/B/C/D/E: To select one of 5 preset station groups (A

to E)

PRESET –/+: To select a preset station number (1 to 8)

e u/d

Select DSP program parameters and SET MENU items.

r SET MENU

Enters the SET MENU.

t POWER

Turns on the power of this unit.

y STANDBY

Sets this unit in the standby mode.

7

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

A B

u VOLUME +/–

Increases or decreases the volume level.

i MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

EFFECT

Switches the effect speakers (center and rear) on and off

in the following cases:

• When the selector dial is set to the DSP/TUN position.

• While the indicator is lit for about 3 seconds after

pressing DSP.

Description of the Numeric

Buttons

The numeric buttons function in various ways depending

on the position of the selector dial or the combination of

other instructions.

■ When selecting an input source

Input selector

buttons

1 Press INPUT regardless of the position of

the selector dial.

The indicator lights up for about 3 seconds.

2 You can select an input source with the

numeric buttons while the indicator is lit.

■ When selecting a DSP program

and turning on or off the effect

speakers (center and rear)

DSP program

group buttons

A

1 Press DSP regardless of the position of the

selector dial.

The indicator lights up for about 3 seconds.

2 You can select a DSP program with the

numeric buttons, turn on or off the effect

speakers (center and rear) by pressing

EFFECT and turn on or off the Dolby Digital

Matrix 6.1 or DTS ES decoder by pressing

6.1/ES while the indicator is lit.

B

1 Set the selector dial to the DSP/TUN

position.

2 You can select a DSP program directly with

the numeric buttons, turn on or off the effect

speakers (center and rear) by pressing

EFFECT and turn on or off the Dolby Digital

Matrix 6.1 or DTS ES decoder by pressing

6.1/ES.

8

CONTROLS AND FUNCTIONS

STANDBY

/ON

–

+

–

+

SURROUND

DIGITAL

TUNER

DSP

30° 30°

■ When selecting a preset station

number

1 Set code number “0023” in the AMP/TUN (or

DSP/TUN) position.

See page 54 for setting the code.

2 Set the selector dial to the AMP/TUN (or

DSP/TUN) position.

3 You can select a preset station number

directly with the numeric buttons (1 to 8).

See page 34.

Using the Remote Control

Approximately 6 m (20 feet)

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

9

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

DIGITAL

DTS MOVIE THEATER 1

2

DOLBY DIGITAL

PRO LOGIC ENTERTAINMENT

DSP

6.1/ES

PCM

PRO LOGIC

A

SP

B

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

V-AUX

DVD

MD/TAPE

CD-R

TUNER

CD

PHONO

VIRTUAL

PS

PTY

RT

CT

PTY

HOLD

EON

STEREO

AUTO

NEWS INFO AFFAIRS SPORT

MEMORY TUNED

VOLUME

dB

ms

SLEEP

1 234 wq87

apio

6

uyre t

09 5

Front Panel Display

1 t indicator

Lights up when the built-in DTS decoder is on.

2 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see

page 29).

3 g and o indicators

Light up according to the type of Dolby signals this unit

is reproducing. “ g ” lights up when the built-

in Dolby Digital decoder is on. “ o ” lights up

when the built-in Dolby Pro Logic decoder is on.

4 x indicator

Lights up when you select a DSP program.

5 DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or q/DTS SURROUND DSP program is

selected.

6 PTY HOLD indicator

Lights up while searching for stations in the PTY SEEK

mode.

7 RDS mode indicators

The name(s) of the RDS data offered by the currently

received RDS station light(s) up. Illumination of the red

indicator next to the RDS data name shows that the

corresponding RDS mode is now selected.

8 EON indicator

Lights up when an RDS station that offers the EON data

service is being received.

9 STEREO indicator

Lights up when the unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

0 AUTO indicator

Shows that this unit is in the automatic tuning mode.

q VOLUME level indicator

Indicates the volume level.

w Input source indicator

Shows the current input source with the arrow-shaped

cursor.

e c indicator

Lights up when the built-in Dolby Digital Matrix 6.1 or

DTS ES decoder is on.

r v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

t SP A/B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

y Headphones indicator

Lights up when headphones are connected.

u Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

i MEMORY indicator

Flashes to show a station can be stored.

o Program type name indicators

The name of the selected program type lights up when the

“EON” indicator lights up.

p TUNED indicator

Lights up when this unit tunes in to a station.

a SLEEP indicator

Lights up while the sleep timer is on.

10

CONTROLS AND FUNCTIONS

(Europe model)

Rear Panel

1 DIGITAL INPUT jacks

2 DIGITAL OUTPUT jacks

3 Antenna input terminals

See page 30 for connection information.

4 Audio component jacks

See pages 12 and 13 for connection information.

5 Video component jacks

See pages 14 and 15 for connection information.

6 Speaker terminals

See pages 16 and 17 for connection information.

7 OUTPUT jacks

See page 18 for connection information.

8 AC power cord

Connect to a power outlet.

9 AC OUTLET(S)

Use these outlets to supply power to your other A/V

components (see page 19).

0 6CH INPUT jacks

See pages 13 and 18 for connection information.

q IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance. Set this unit in the standby mode

before you change the setting of this switch (see page 19).

DIGITAL OUTPUT AUDIO AUDIO VIDEO

SPEAKERS OUTPUT

MAIN

CENTER

REAR

(SURROUND)

TUNER

DIGITAL INPUT 6CH INPUT

MD/

TAP E

CD-R

CD

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B

/

C

B

P

R

/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

MAIN

CENTER

SUB

WOOFER

R L

LR

R

+

–

L

R L

D-TV/LD

A

Y

P

B

/

C

B

P

R

/

C

R

MONITOR

OUT

Y

P

B

/

C

B

P

R

/

C

R

+

–

+

– –

+

B

REAR

(SURROUND)

MAIN A OR B: 4

MIN. /SPEAKER

A

+

B: 8

MIN. /SPEAKER

CENTER

: 6

MIN. /SPEAKER

REAR

: 6

MIN. /SPEAKER

MAIN A OR B: 8

MIN. /SPEAKER

A

+

B:

16

MIN. /SPEAKER

CENTER

: 8

MIN. /SPEAKER

REAR

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SWITCHED

100W MAX. TOTAL

AC OUTLETS

MAINS

876

5

4

32

1

9

0

q

As this terminal is used

for an examination in the

factory, do not connect

any equipment to this

terminal.

11

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound-

field quality with a 5-speaker system, using left and right

main speakers, left and right rear speakers, and a center

speaker. If you use different brands of speakers (with

different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not

shift smoothly. We recommend that you use speakers

from the same manufacturer or speakers with the same

tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). If

for some reason it is not practical to use a center speaker,

you can do without it. Best results, however, are obtained

with the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use

high-performance models that can reproduce sounds over

the full range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

Speaker Placement

Refer to the following diagram when you place the

speakers.

Main

speaker (L)

Center speaker

Main speaker (R)

Rear speaker (R)

Rear speaker (L)

1.8 m

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (approx. 6 feet)

above the floor.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will

be heard from the left and right main speakers. In this case,

“1A CENTER SP” on the SET MENU is set to NONE (see

page 41 for details).

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

CAUTION

Some types of speakers interfere with a video monitor.

If this problem occurs, move the speakers away from

the monitor. If you cannot avoid installing the center

speaker or subwoofer near the video monitor, use a

magnetically shielded speaker.

PREPARATION

Subwoofer

12

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different jack names. Refer to the operation instructions

for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling

system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. When you connect components to

both the COAXIAL and OPTICAL jacks, priority is given

to the input signals from the COAXIAL jack. All digital

input jacks are acceptable for 96-kHz sampling digital

signals (see page 25 for details).

y

• You can designate the input for each digital jack according to

your component by using “7 I/O ASSIGNMENT” on the SET

MENU (see page 44 for details).

About the dust protection cap

Pull out the cap from the optical jack

before you connect the fiber optic cable.

Do not discard the cap. When you are not

using the optical jack, be sure to put the

cap back in place. This cap protects the

jack from dust.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM

or high-output MC cartridge. If you have a turntable with

a low-output MC cartridge, use an inline boosting

transformer or MC-head amplifier when connecting to

these jacks.

y

• The GND terminal does not electrically ground the turntable. It

simply reduces noise in the signal. In some cases, you may

hear less noise if you do not connect to the GND terminal.

■ Connecting a CD player

y

• The COAXIAL CD and OPTICAL CD jacks are available for a

CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and

OPTICAL CD jacks, priority is given to the input signals from

the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

y

• Only digital signals input from a source such as a CD or DVD

are output from the DIGITAL OUTPUT jacks.

• When you connect your recording component to both the

analog and digital input and output jacks, the priority is given

to the digital signal.

• You can connect an MD recorder to any digital input jack by

using “7 I/O ASSIGNMENT” on the SET MENU (see

page 44).

Notes

• When you connect a recording component to this unit, keep its

power on while using this unit. If the power is off, this unit may

distort the sound from other components.

• When you record from a source component connected to this

unit while this unit is set in the standby mode, the recorded

sound may be distorted. To avoid this problem, turn on this

unit.

13

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL OUTPUT AUDIO AUDIO VIDEO

TUNER

DIGITAL INPUT 6CH INPUT

MD/

TAPE

CD-R

CD

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B/

C

B

PR/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

D-TV/LD

Y

P

B/

C

B

PR/

C

R

MONITOR

OUT

Y

P

B/

C

B

PR/

C

R

L

R

L

R

O

OUTPUT

GND

L

R

L R

INPUT OUTPUT INPUTOUTPUT

OUTPUT

O

C

COAXIAL

OUTPUT

L

R

L

R

OPTICAL

OUTPUT

OPTICAL

INPUT

OPTICAL

INPUT

OPTICAL

OUTPUT

SUBWOOFER

OUTPUT

CENTER OUTPUT

MAIN

OUTPUT

SURROUND

OUTPUT

L R

L

R

C

O

MD recorder or

tape deck

indicates signal direction

indicates coaxial cables

CD recorder

CD player

Turntable

External decoder

See page 18.

indicates left analog cables

indicates right analog cables

indicates optical cables

(Europe model)

14

CONNECTIONS

Y

P

B/

C

B

PR/

C

R

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video

signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.

The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO

jacks are separated into luminance (Y) and color difference (P

B

/C

B

, P

R

/C

R

) video signals. The jacks are also separated

into three for each signal. The description of the component video jacks may be different depending on the component

(e.g. Y, C

B

, C

R

/Y, P

B

, P

R

/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the

S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks

on your video component to the COMPONENT VIDEO jacks.

VIDEO jack

(composite)

S VIDEO jack COMPONENT VIDEO

jacks

y

• Each type of video jack works independently. Signals input

through the composite video, S-video and component jacks are

output through the corresponding composite video, S-video,

and component jacks, respectively.

• If you make S-video connections to this unit, it is not necessary

to make composite video connections. If both types of

connections are made, this unit gives priority to the S-video

signal.

• You can designate the input for the COMPONENT VIDEO A

and B jacks according to your component by using “7 I/O

ASSIGNMENT” on the SET MENU (see page 44 for details).

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when

connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being

connected.

■ Video monitor with a 21-pin connector

Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.

■ VIDEO AUX jacks (on the front panel)

These jacks are used to connect any video input source

such as a game console to this unit.

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

O

V

L

R

S

Game console

15

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL OUTPUT AUDIO AUDIO VIDEO

TUNER

DIGITAL INPUT 6CH INPUT

MD/

TAPE

CD-R

CD

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B

/

C

B

P

R

/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

D-TV/LD

Y

P

B

/

C

B

P

R

/

C

R

MONITOR

OUT

Y

P

B

/

C

B

P

R

/

C

R

L

R

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

*1

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO INPUT

AUDIO OUTPUT

COAXIAL

OUTPUT

OPTICAL

OUTPUT

RF

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

RF

INPUT

O

V

S

O

L

R

L

R

L

R

V

S

COMPONENT

INPUT

COMPONENT

OUTPUT

COMPONENT

OUTPUT

V

S

V

S S

L

R

C

V

S

L

R

V

L

S

R

V

C

O

Note

• If your LD player has an Dolby Digital RF signal output jack, connect it to this unit

through an RF demodulator (separately purchased).

indicates signal direction

indicates left analog cables

indicates right analog cables

indicates S-video cables

TV/digital TV or

LD player

DVD player

Cable TV or

Satellite tuner

VCR 1 or VCR 2/

DVR (digital

video recorder)

Video monitor

indicates coaxial cables

indicates optical cables

indicates video cables

(Europe model)

LD player

No connection

SCART-plug

*1 You can connect the Dolby

Digital RF signal output of

your LD player to the

COAXIAL jack by using

“7 I/O ASSIGNMENT” on

the SET MENU (see

page 44).

RF

demodulator

16

CONNECTIONS

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage the unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

12

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

2

1

3

Red: positive (+)

Black: negative (–)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

10 mm (3/8”)

17

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

SPEAKERS OUTPUT

MAIN

CENTER

REAR

(SURROUND)

MAIN

CENTER

SUB

WOOFER

R L

LR

R

+

–

L

R L

A

+

–

+

– –

+

B

REAR

(SURROUND)

MAIN A OR B: 4

MIN. /SPEAKER

A

+

B: 8

MIN. /SPEAKER

CENTER

: 6

MIN. /SPEAKER

REAR

: 6

MIN. /SPEAKER

MAIN A OR B: 8

MIN. /SPEAKER

A

+

B:

16

MIN. /SPEAKER

CENTER

: 8

MIN. /SPEAKER

REAR

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SWITCHED

100W MAX. TOTAL

AC OUTLETS

MAINS

Main speakers A

Right Left

Main speakers B

Right Left

(Europe model)

Center speaker Rear speakers

Right Left

Subwoofer

system

Subwoofer connection

See “SUBWOOFER jack” on page 18.

18

CONNECTIONS

Connecting to an External

Amplifier

If you want to increase the power output to the speakers,

or want to use another amplifier, connect an external

amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for

output to an external amplifier, it is not necessary to use the

corresponding SPEAKERS terminals.

1 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the

BASS, TREBLE and BASS EXTENSION settings.

2 SUBWOOFER jack

When using a subwoofer with built-in amplifier, including

the YAMAHA Active Servo Processing Subwoofer

System, connect the input jack of the subwoofer system

to this jack. Low bass signals distributed from the main,

center and/or rear channels are directed to this jack. (The

cut-off frequency of this jack is 90 Hz.) The LFE (low-

frequency effect) signals generated when Dolby Digital or

DTS is decoded are also directed if they are assigned to

this jack.

Notes

• Adjust the volume level of the subwoofer with the control on

the subwoofer. The subwoofer volume cannot be adjusted from

this unit.

• Depending on the settings of “1 SPEAKER SET”, “10A LFE

LEVEL” and “11 DTS LFE LEVEL” on the SET MENU,

some signals may not be output from the SUBWOOFER jack.

3 CENTER jack

Center channel line output jack.

4 REAR (SURROUND) jacks

Rear channel line output jacks.

OUTPUT

MAIN

CENTER

SUB

WOOFER

R L

LR

REAR

(SURROUND)

1

2

3

4

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left

and right MAIN, CENTER, left and right SURROUND

and SUBWOOFER) for discrete multi-channel input from

an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, changing

items 1A to 1E on the SET MENU is not affected.

La pagina sta caricando ...

Yamaha RX-V800RDS Manuale utente

Yamaha RX-V800RDS Manuale utente

in altre lingue

Documenti correlati

Altri documenti