Linn Akurate DS Manuale del proprietario

OWNER’S MANUAL

AKURATE DS

DIGITAL STREAM PLAYER

i

AKURATE DS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use the apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarised or grounding type plug. A

polarised plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong is provided for your safety. If the provided plug does not ﬁt into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and at the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods

of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or

plug has been damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

15. Wall or ceiling mounting. Mount the apparatus to a wall or ceiling only as

recommended by the manufacturer.

16. Power sources. Connect the apparatus to a power supply only of the type

described in the operating instructions or marked on the apparatus.

17. Mains plug. Use the mains plug to disconnect the apparatus from the mains

supply. The mains plug must be accessible at all times. Use the mains switch

(if applicable) when the apparatus is not in use.

18. Power lines. An outdoor antenna should be located away from power lines.

19. Outdoor antenna grounding. If an outdoor antenna is connected to the

apparatus, ensure that the antenna system is grounded to provide some

protection against voltage surges and static build up. In the USA see article

810 of the National Electrical Code ANSI/NFPA 70 concerning installation

requirements.

20. Telephone line. Do not connect the apparatus to a telephone line except where

speciﬁcally instructed to do so.

21. Objects and liquid entry. Do not let objects or liquids fall into the apparatus.

Do not expose the apparatus to dripping or splashing. Do not place a vessel

containing liquid on top of the apparatus.

22. No naked ﬂame sources, such as lighted candles, should be placed on the

apparatus.

23. The apparatus has been designed for use in moderate and tropical climates.

24. This apparatus is supplied with a remote control unit which contains replaceable

non-rechargeable batteries. The remote control unit and the batteries must not

be exposed to excessive heat such as sunshine, ﬁre or the like. The disposal of

used batteries should be in accordance with local re-cycling and waste disposal

regulations. Never dispose of batteries in a ﬁre because they may explode and

cause injury.

ii

AKURATE DS

Explanation of symbols used in this manual or on the rear/underside of the

apparatus:

This symbol is intended to alert the user to the presence of uninsulated

dangerous voltages within the enclosure of sufﬁcient magnitude to

cause electric shock.

This symbol is intended to alert the user to the presence of important

operation, maintenance and servicing information in the instruction and

service manuals.

For apparatus connected to the mains electricity supply

CAUTION

• To reduce the risk of electric shock do not remove the cover.

• No user serviceable parts inside.

• Refer servicing to qualiﬁed service personnel.

• Replace the mains fuse in the plug with one of the same type

and rating.

• Disconnect supply cord before changing fuse.

WARNING

To reduce the risk of ﬁre or electric shock do not expose this

apparatus to rain or moisture. Shock hazard - do not open.

MAINS PLUGS

• This apparatus is supplied with a non-rewireable mains plug for the

intended country.

• Replacement mains leads can be obtained from your Linn retailer.

Should you need to change the plug please dispose of it carefully. A plug

with bared conductors is dangerous if engaged in a live socket.

• The Brown wire must be connected to the Live (Line) supply pin.

• The Blue wire must be connected to the Neutral supply pin.

• The Green/Yellow wire must be connected to the Earth (Ground)

supply pin.

Please contact your retailer or a competent electrician if you are in any doubt.

Refer to the rear or underside of the product for fuse and power

consumption information.

IMPORTANT SAFETY INSTRUCTIONS

Fuse replacement

This appliance is ﬁtted with a non-rewireable 13 amp mains plug. The plug

contains a 5 amp fuse. If the fuse has blown it can be replaced as follows:

a) Pull out the red fuse cover/carrier.

b) Remove and dispose of the blown fuse.

c) Fit a new 5 amp BS1362 approved fuse into the carrier and push the

carrier back into the plug.

Always ensure the fuse cover is ﬁtted. If the fuse cover is missing do not use

the plug. Contact your Linn retailer to obtain a replacement fuse cover.

Fuses are for ﬁre protection and do not protect against electric shock.

Mains plug replacement

Should your mains plug need replacing and you are competent to do

this proceed as follows. If you are in doubt contact your Linn retailer or a

competent electrician.

a) Disconnect the plug from the mains supply.

b) Cut off the plug and dispose of it safely. A plug with bared conductors is

dangerous if engaged in a live socket.

c) Only ﬁt a 13 amp BS1363A approved plug with a 5 amp fuse.

d) The cable wire colours or a letter will be marked at the connection points

of most quality plugs.

Attach the wires securely to their respective points. The Brown wire must go

to the Live pin, the Blue wire must go to the Neutral pin, and the Green/Yellow

wire must go to the Earth pin.

e) Before replacing the plug top ensure that the cable restraint is holding

the outer sheath of the cable ﬁrmly and that the wires are correctly

connected.

WARNING

THIS APPLIANCE MUST BE EARTHED.

Linn Products Ltd declare that this product is in conformance with the Low

Voltage Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC

as amended by 92/31/EEC and 93/68/EEC.

The conformity of the designated product with the provisions of Directive

number 73/23/EEC (LVD) is proved by full compliance with the following

standards:

Standard number Date of issue Test type

EN60065 2002 General requirements

Marking

Hazardous radiation

Heating under normal conditions

Shock hazards under normal

operating conditions

Insulation requirements

Fault conditions

Mechanical strength

Parts connected to the mains

supply

Components

Terminal devices

External ﬂexible cords

Electrical connections and

mechanical ﬁxings

Protection against electric shock

Stability and mechanical hazards

Resistance to ﬁre

The conformity of the designated product with the provisions of Directive

number 89/336/EEC (EMC) is proved by full compliance with the following

standards:

Standard number Date of issue Test type

EN55013 2001 Conducted emissions

EN55013 2001 Absorbed emissions

EN55020 2002 Immunity

UK Users Please Read This

Important Safety Information

CE Declaration of Conformity

iii

AKURATE DS

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Waste Electrical and Electronic Equipment Directive Directive 2002/96/

EC of the European Parliament and of the Council

The symbol (right) is shown on this product. It indicates that the

product should not be disposed of with regular household waste,

but should be disposed of separately.

Electrical and electronic equipment can contain materials that are hazardous

to the environment and human health and therefore should be disposed of

at a designated waste facility or returned to your retailer for the appropriate

recycling to take place (see www.linn.co.uk for further information).

If you wish to dispose of this product and the product still functions, please

consider recycling/reusing it by donating it to a charity shop, selling it or part-

exchanging it with your retailer.

FCC notice

Waste Electrical and Electronic Equipment

(WEEE) Directive

Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow,

G76 OEQ, Scotland, United Kingdom

a retrieval system, or transmitted, in any form or by any means, electronic,

mechanical, photocopying, recording, or otherwise, without the prior written

permission of the publisher.

The content of this manual is furnished for information use only, is subject to

change without notice, and should not be construed as a commitment by

Linn Products Limited. Linn Products Limited assumes no responsibility or

liability for any errors or inaccuracies that may appear in this manual.

Trade marks used in this publication: Linn and the Linn logo are registered

trade marks of Linn Products Limited. Akurate and Klimax are trade marks

of Linn Products Limited.

UPnP™ is a certiﬁcation mark of the UPnP Implementers Corporation.

Linn Products Limited disclaims any proprietary interest in trade marks and

trade names other than its own.

Pack 1369/E

Copyright and Acknowledgements

iv

AKURATE DS

v

INTRODUCTION 1

INSTALLATION 2

Unpacking 2

Positioning 2

Cleaning 2

Connecting to the mains supply 2

OPERATION 3

Playing music 3

Selecting music 3

Controlling playback 5

Current Playlist 6

Volume 6

Standby 6

Front panel and handset 7

Front panel 7

Handset 8

Front panel display 9

Adding music to the library 9

TECHNICAL SPECIFICATION 10

GUARANTEE AND SERVICE 11

THIRD-PARTY COPYRIGHT INFORMATION 12

CONTENTS

AKURATE DS

Since Linn’s inception with the production of the Sondek LP12 turntable in

1972, our aspiration has been to get you as close to the sound of the original

recording as possible.

Over the many years since, we have remained committed to this goal by

exploiting the latest developments in hi-ﬁ technology. The Akurate DS digital

stream player exempliﬁes this commitment and dedication. Developed from

our ﬂagship Klimax DS player, it utilises sophisticated processing of the digital

audio signal drawn from an external storage device, to produce crystal-clear,

error-free audio. The advanced circuitry, combined with an absence of any

mechanical noise due to their being no moving parts, ensures the Akurate DS

delivers astounding musical performance. The Linn GUI is a simple and fun

interface to use, and provides instant access to your CD and downloaded

music collection.

In partnership with the Akurate Kontrol pre-ampliﬁer, Akurate power ampliﬁers

and Akurate loudspeakers, we are certain that you will be astonished by the

quality of your Linn system now, and in the years to come.

INTRODUCTION

1

AKURATE DS

Important:

The Akurate DS player must be installed by an engineer/technician trained

in networks and network security. Linn Products Limited cannot be held

responsible for any network security compromise and/or loss of data due to

improper installation.

Unpacking

The Akurate DS player is supplied with the following:

• handset

• 2 x AAA batteries for the handset

• 1 pair of black interconnect cables

• RS232 lead

• mains lead

• CD-ROM (contains system software, installation manual and

owner’s manual)

We recommend that you retain all packaging in case you need to transport

the Akurate DS at a later date.

Positioning

You can position your Akurate DS almost anywhere you ﬁnd convenient, but

please consider the following points:

• The unit should be placed on a ﬂat, stable and rigid surface.

• Do not position the unit where sunlight can shine (whether directly,

diffused or reﬂected) on its display as the infra-red (IR) radiation in

sunlight will be picked up by the unit’s IR remote sensor and this can

adversely affect its operation. Similarly, some electrical devices such

as plasma TVs, ﬂuorescent lights and energy saving lamps can emit IR

which can likewise affect the operation.

• For best performance do not stack the unit with other products. Ideally,

position the unit on a shelf by itself or, if proximity to other products is

unavoidable, positioning side-by-side is preferable to stacking.

• The unit should not be situated above, or directly adjacent to, sources of

heat such as radiators, power ampliﬁers etc. Nor should it be enclosed in

a cabinet with such devices.

INSTALLATION

• The unit itself produces very little heat; however it is advisable to allow a

little space to the sides, rear and above the unit (ideally 10 cm / 4”) for air

circulation which will allow any heat to dissipate.

Cleaning

Disconnect the Akurate DS from the power supply before cleaning. Remove

dust and ﬁngerprints with a soft, dry cloth.

Connecting to the mains supply

The Akurate DS contains an automatic internal mains voltage switch. This

switch operates on all worldwide mains voltages from 100 V to 240 V. The unit

can be connected to any worldwide mains voltage with no adjustment.

This unit must be earthed. Use the earthed moulded mains lead

supplied, or if no mains earth is available, ensure the product’s

EARTH GROUND connector is connected to an earthing terminal.

2

AKURATE DS

3

OPERATION

Playing music

If you are using a Linn Akurate Kontrol pre-ampliﬁer with the Akurate DS,

switch on the Akurate Kontrol ﬁrst and wait for it to show the

 (standby)

symbol before powering-up the Akurate DS. When the Akurate DS is

switched on, a ﬂashing dot will appear on the display. Wait until the dot is

replaced by the

 symbol before following the steps below.

3. From the Source window, select ‘Akurate DS’.

4. From the Library window, select the storage device that

contains the music you want to listen to by tapping it twice.

2. From the Room window, select the appropriate room. This will

automatically bring your Akurate DS (and Akurate Kontrol) out of

standby.

1. Turn on your control device. If the Linn GUI does not run automatically,

double-click the Linn GUI icon.

Selecting music

AKURATE DS

4

5. Tap ‘Music’ twice.

Note:

When using the Linn GUI, tap

in the top of the left-hand window to

return to the previous screen.

6. Select the category you want to browse by tapping it twice.

8. The folder symbol indicates that an item contains sub items (e.g. a

folder will be shown next to the name of an album to indicate that the

album’s tracks are held within the folder). Tap an item to highlight it, then

tap it again to reveal the contents of the folder.

7. Scroll to the music you want to play by placing the control device’s

stylus in the left-hand window and ‘drawing’ circles (clockwise to scroll

downwards, anti-clockwise for upwards).

Alternatively, tap the symbol to add the selection to the Current

Playlist window. To start playback, tap the selection within the Current

Playlist window to highlight it, then tap .

9. To play an album, track, or all tracks by a particular artist (depending on

the view you are currently on), tap the selection to highlight it, then tap

.

Your selection will move to the Current Playlist window and playback will

begin.

AKURATE DS

5

10. Continue to add selections to the Current Playlist by highlighting artists/

albums/tracks and tapping the symbol. You can add new selections

to the bottom of the playlist, or place them after the currently playing

track (if playback has not started they will be added to the top of the

playlist). The icon shown at the bottom-right of the left-hand window

determines where the selection will be placed. This icon means

that the selection will be placed at the bottom of the playlist. This icon

means that the selection will be placed after the currently playing track.

Tap the icon to change it.

Note:

Up to 1,000 tracks can be added to the Current Playlist. The bar at the

bottom of the Current Playlist window tells you how many tracks are in the

playlist.

Controlling playback

Control playback by using the icons.

While a track is playing, tapping will restart it, unless another selection

is currently highlighted in which case the highlighted track will begin playing.

Tap on the progress bar to jump forward or backwards within the currently

playing track.

Note:

You can also control playback using the front panel keys or the supplied

handset, see Front panel and handset, pages 7 to 9.

AKURATE DS

6

Volume

You can use the icons on the Linn GUI to control volume

if your Akurate DS is connected to a Linn Akurate Kontrol pre-ampliﬁer.

Volume range on the Akurate Kontrol is from 0 to 100 (unless Volume Limit on

the Akurate Kontrol has been set to less than 100).

Note:

If the Linn pre-ampliﬁer in your system is not an Akurate Kontrol, you can

adjust the volume using the handset supplied with the Akurate DS or

pre-ampliﬁer, or the pre-ampliﬁer’s front panel keys.

Standby

To put the Akurate DS into standby using the Linn GUI, tap the source/room

key at the top-right of the GUI, then tap the

 icon for the appropriate room,

in the left-hand window.

The Akurate DS can also be put into or out of standby using the key on

the front panel or handset.

Note:

The tracks in the Current Playlist will remain there if the Akurate DS is put into

then brought out of standby.

Current Playlist

Scroll up and down through the playlist by placing the control device’s stylus

in the Current Playlist window and ‘drawing’ circles (clockwise to scroll

downwards, anti-clockwise for upwards).

Play any track in the Current Playlist by highlighting it, then tapping

Playback of the playlist will continue from that point.

Note:

The tracks in the Current Playlist will remain there if the Akurate DS is put into

then brought out of standby.

To delete individual tracks from the playlist:

• Tap on the track you wish to delete.

• Tap the symbol next to the track’s title.

To delete the entire playlist:

• Tap the symbol at the top-right of the Current Playlist window.

.

AKURATE DS

7

Front panel and handset

Once you have added tracks to the Current Playlist, you can use the front

panel keys or supplied handset to control playback.

Front panel

1. DISPLAY Cycles through the various display modes

2. Front panel display

3.

Brings the unit out of, or puts into, standby

4.

Previous track selection. Press and hold to skip backwards through

the tracks in the Current Playlist

5.

Next track selection. Press and hold to skip forwards through the

tracks in the Current Playlist

6.

Stops playback

7.

Starts playback of the Current Playlist. If playback has been started

and then stopped, pressing

will begin playback from the start

of the last track played. During playback, a quick press of will

pause playback. Press

again to resume playback. Press and

hold

for two seconds to replay the current track.

Note:

You can control playback of the Current Playlist using the handset or front

panel, even if the Linn GUI has been turned off.

AKURATE DS

DISPLAY

1

4 65 7

2 3

AKURATE DS

8

1. LEDs Indicate the mode of the handset when a key is pressed

2. DVD Puts the handset into Disc mode. The handset should be in Disc

mode to operate the Akurate DS

3.

 Stops playback

4.

 Starts playback of the Current Playlist. If playback has been

started and then stopped, pressing

 will begin playback from the

start of the last track played

5.

; Pauses playback

6.

7 Fast search backwards

7.

8 Fast search forwards

8. DISP Cycles through track information on the front panel display

9.

 Enters/exits standby

10.

9 Previous track selection

11.

: Next track selection

Keys and functions of the handset not listed above do not function with the

Akurate DS player but may with other Linn products.

Note:

You can control playback of the Current Playlist using the handset or front

panel, even if the Linn GUI has been turned off.

Handset

1

2

4

8

5

6

7

3

9

11

10

AKURATE DS

9

Handset modes

The handset has been designed to provide simpler, more intuitive control

over a range of Linn products. In order to achieve this, the handset can be

operated in various handset modes which assign differing functionality to

some of the keys. The handset mode is indicated by the LEDs at the top-left

of the handset, which will light when a key is pressed.

The handset should be used in Disc mode for operating the Akurate DS.

Disc mode – press the DVD key to set the handset to Disc mode. The DVD

functions will be assigned as the primary handset keys and the DVD LED will

light when a key is pressed.

Note:

Volume control is always available, regardless of the mode the handset is in.

If you are using a Linn pre-ampliﬁer or AV system controller with your

Akurate DS, you can use the same handset to operate both Linn products.

For some functionality you may have to use the DVD and AMP buttons to

switch between handset modes.

Front panel display

Key to symbols shown on the front panel display:

 Play

; Pause

 Stop

: Skip to next track

9 Skip to previous track

8 Fast search forwards

7 Fast search backwards

 Standby

The front panel of the Akurate DS displays information relating to the currently

playing track. Repeatedly press DISP on the handset, or DISPLAY on the

front panel, to cycle through the information in the following order:

Elapsed track time

Remaining track time

Track audio data (sample rate/bit depth)

Track encoding data (kilobits per second/format)

Track number within total number of tracks in the playlist

Track title *

Artist *

Album title *

Regardless of the information shown on the display, you can see the currently

playing track title, artist and album title by pressing and holding DISP or

DISPLAY for two seconds.

Whenever a new track begins playing (or playback has been stopped then

restarted), the track title, artist name and album title will scroll across the

display.** While the text is scrolling, pressing DISP or DISPLAY will return the

display to the previous view.

* If the text is too long to appear in full on the display, press and hold DISP or

DISPLAY for two seconds to see the whole text scroll.

** This feature can be turned off or on via the Linn Conﬁguration software

supplied with the Akurate DS. (Adjustments made to the system via the

Linn Conﬁguration software should only be done by your Linn installer.)

Adding music to the library

If you wish to add a CD to your music library, insert the CD into the PC that

is connected to your storage device (NAS) and, using the ripping software

conﬁgured by your Linn installer, rip the CD. Once the CD has been ripped it

will automatically be added to the music library on the Linn GUI.

AKURATE DS

10

TECHNICAL SPECIFICATION

Date of introduction November 2007

Type Digital stream player

Size (H) 80 mm x (W) 381 mm x (D) 360 mm

(H) 3.1 inches x (W) 15 inches x (D) 14.2 inches

Weight 4.2 kg

9.2 lb

Supported ﬁle types WAV, FLAC, MP3

Audio sample rates 44.1 k, 48 k, 88.2 k, 96 k, 176.4 k, 192 k

Word depths 16 – 24 bits

Analogue audio

outputs

Stereo RCA phono sockets, stereo XLR

balanced audio outputs

Ethernet interface 100Base-T RJ45

Control protocol Compatible with UPnP

™

media servers,

UPnP

™

AV 1.0 control points

Local control Front panel 6 button interface

RS232 x 4

Luminous remote control handset

128 x 32 front panel display

Power supply Switching power supply with auto-ranging

(AC 100 – 120 V @ 50 – 60 Hz)

(AC 220 – 240 V @ 50 – 60 Hz)

Power consumption 13 W

AKURATE DS

This product is guaranteed under the conditions which apply in the country of

purchase and your statutory rights are not limited. In addition to any statutory

rights you may have, Linn undertake to replace any parts which have failed

due to faulty manufacture. To help us, please ask your Linn retailer about the

Linn warranty scheme in operation in your country.

In parts of Europe, the United States of America and some other markets,

extended warranty may be available to customers who register their purchase

with Linn. A warranty registration card is included with the product and should

be returned to Linn as soon as possible. Alternatively, you can register your

warranty online at www.linn.co.uk.

WARNING

Unauthorised servicing or dismantling of the product invalidates the

manufacturer’s warranty. There are no user serviceable parts inside the

product and all enquiries relating to product servicing should be referred to

authorised retailers only.

Technical support and information

For technical support, product queries and information, please contact either

your local retailer or one of the Linn ofﬁces opposite.

Full details of your local retailer/distributor can be found on the Linn web site:

www.linn.co.uk.

Important

Please keep a copy of the sales receipt to verify the purchase date of the

product.

Please ensure that your equipment is insured by you during any transit or

shipment for repair.

GUARANTEE AND SERVICE

Linn Products Limited

Glasgow Road, Waterfoot, Eaglesham, Glasgow G76 0EQ, Scotland, UK

Phone: +44 (0)141 307 7777

Fax: +44 (0)141 644 4262

Helpline: 0500 888909

Email: [email protected]

www.linn.co.uk

Linn Incorporated

8787 Perimeter Park Boulevard, Jacksonville, FL 32216, USA

Phone: +1 (904) 645 5242

Fax: +1 (904) 645 7275

Helpline: 888-671-LINN

Email: [email protected]

www.linninc.com

Linn Deutschland GmbH

Hühnerposten 1d, D-20097 Hamburg, Deutschland

Phone: +49-(0) 40-890 660-0

Fax: +49-(0) 40-890 660-29

Email: [email protected]

www.linn.co.uk

11

AKURATE DS

12

The Akurate DS uses software from rtems.com, the Xiph.org foundation, and

FreeBSD.

Rtems.com:

LICENSE INFORMATION

RTEMS is free software; you can redistribute it and/or modify it under terms

of the GNU General Public License as published by the Free Software

Foundation; either version 2, or (at your option) any later version. RTEMS is

distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;

without even the implied warranty of MERCHANTABILITY or FITNESS FOR

A PARTICULAR PURPOSE. See the GNU General Public License for more

details. You should have received a copy of the GNU General Public License

along with RTEMS; see ﬁle COPYING. If not, write to the Free Software

Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.

As a special exception, including RTEMS header ﬁles in a ﬁle, instantiating

RTEMS generics or templates, or linking other ﬁles with RTEMS objects to

produce an executable application, does not by itself cause the resulting

executable application to be covered by the GNU General Public License. This

exception does not however invalidate any other reasons why the executable

ﬁle might be covered by the GNU Public License.

A copy of the GPL is included on the accompanying CD-Rom in the licenses

directory.

Information on obtaining access to the GPL code used in this product is

available at http://oss.linn.co.uk

Alternatively, write to Open Source Software Licensing, Linn Products Limited,

Glasgow Road, Waterfoot, Eaglesham, Glasgow G76 0EQ, Scotland, UK

THIRD-PARTY COPYRIGHT

INFORMATION Flac from the Xiph.org foundation:

Redistribution and use in source and binary forms, with or without

modiﬁcation, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice,

this list of conditions and the following disclaimer.

• Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the documentation

and/or other materials provided with the distribution.

• Neither the name of the Xiph.org Foundation nor the names of its

contributors may be used to endorse or promote products derived from this

software without speciﬁc prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS “AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

La pagina sta caricando ...

Linn Akurate DS Manuale del proprietario

Linn Akurate DS Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti