Ubiquiti USW-Flex Guida Rapida

Marca: Ubiquiti

Modello: USW-Flex

Categoria: Switch di rete

Tipo: Guida Rapida

Indoor/Outdoor 5-Port PoE

Gigabit Switch with

802.3bt Input Power Support

Model: USW-Flex

Package Contents

UniFi Switch Flex

Wall Mount Pole Mount Port Cover

Mounting Screws

(Qty. 2)

Screw Anchors

(Qty. 2)

Zip Ties

(Qty. 2)

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.8 or above recommended

• Web Browser: Google Chrome (Other browsers may have

limited functionality)

• UniFi Controller software v5.11.36 (or newer), available at:

ui.com/download/unifi

All UniFi devices support off-site management controllers.

For setup details, refer to the User Guide on the website:

ui.com/download/unifi

Hardware Overview

Front Panel

Port Description

Ports 1-5 RJ45 ports support 10/100/1000 Mbps Ethernet

connections.

PoE In

(Port 1)

Supports 802.3af/at/bt

Top Panel

LEDs

System

State Status

Steady White Factory defaults, awaiting adoption.

Flashing White Bootup in process.

Steady Blue Successfully adopted.

Flashing Blue Firmware upgrade in process.

RJ-45 LEDs

LED

State Status

PoE

Off No PoE

Amber Powered on, IEEE 802.3af

Link/

Speed/

Activity

Off No Link

Green

Link established at 10/100/1000 Mbps

Flashing indicates activity

Hardware Installation

The UniFi Switch can be placed on a flat surface or mounted

on a wall or pole.

Wall Mounting

1. Use the Wall Mount as a template to mark two holes on the

installation surface.

40 mm

2. Use a 6mm drill bit to predrill the two holes.

3. Insert the screw anchors into the predrilled holes and

secure the Wall Mount using the Mounting Screws.

4. Mount the switch to the wall by pressing it over the Wall

Mount and sliding it down until it locks into place.

Magnetic Mounting

1. Slide the Wall Mount into the rear panel of the switch until

it snaps into place.

2. Place or hang the switch on a magnetic surface.

Pole Mounting

1. Slide the two Plastic Zip Ties through the notches in the

Pole Mount and fasten to the pole.

2. Press the switch over the Pole Mount and slide it

down until it locks into place.

NOTE: For outdoor installations, please install the

Port Cover prior to connecting your Ethernet cables.

See Outdoor Installation.

Powering the Switch

Connect an Ethernet cable from an 802.3af/at/bt switch or PoE

adapter to the PoE In port (Port 1) on the switch.

Connecting Ethernet

1. Connect an Ethernet cable from your DHCP server or LAN

device to any port 2 through 5.

NOTE: For outdoor installations, please install the

Port Cover prior to connecting your Ethernet cables.

See Outdoor Installation.

Outdoor Installation

1. Attach the bottom half of the Port Cover to the switch and

snap it into place.

2. Connect an Ethernet cable from an 802.3af/at/bt switch or

PoE adapter to the PoE In port (Port 1) on the switch and a

LAN cable to any port 2 through 5.

3. Place the top half of the Port Cover over the bottom half

and snap them together.

Disconnect Ethernet Cable(s)

1. Remove the Port Cover from the USW-Flex.

2. Disconnect the Ethernet cable(s) from the USW-Flex.

3. Separate the top half of the Port Cover from the bottom half.

4. Slide the Ethernet cables out through the opening of

the Port Cover.

Software Installation

Download and install the latest version of the UniFi Controller

software at ui.com/download/unifi and follow the on-screen

instructions.

Note: If you already have UniFi Controller v5.10.x or

newer installed, skip to Adopting the UniFi Switch.

After you have installed the software and run the UniFi

Installation Wizard, a login screen will appear for the UniFi

Controller management interface. Enter the admin name and

password that you created and click Sign In.

You can manage your network and view network statistics

using the UniFi Controller management interface.

To adopt the UniFi Switch, proceed to the Adopting the UniFi

Switch section.

For information on configuring and using the UniFi Controller

software, refer to the User Guide on the website:

ui.com/download/unifi

Adopting the UniFi Switch

1. From the UniFi Controller dashboard, click Devices in the

left menu bar.

2. On the Devices screen, locate the UniFi Switch in the list

of devices under the Model column. To adopt the UniFi

Switch, click Adopt.

3. The System LED on the UniFi Switch will turn blue to

confirm that it has been successfully adopted.

Enabling PoE Injector Mode

1. In UniFi Controller, click the Devices icon and select

UniFi Switch Flex 5 POE from the list.

2. Click the Config icon in the Properties window.

3. Click General and select PoE Injector.

Note: The option to select PoE Injector will only appear if

the switch is actually powered by a PoE injector.

4. Click Confirm if the USW-Flex is powered by a PoE Adapter

with a power rating of 50V/60W or better. Otherwise, click

Cancel and replace the PoE Adapter with one that does

have a power rating of 50V/60W or better.

5. Once confirmed, click Save under the General section, to

complete the installation.

Specifications

USW-Flex

Dimensions 122.5 x 107.1 x 28.0 mm

(4.82 x 4.22 x 1.10")

Weight 230 g (8.11 oz)

Networking Interfaces (5) 10/100/1000 Mbps RJ45 Ports

Management Interface Ethernet In-Band

Power Method (Port 1)

PoE Mode 1

PoE Mode 2

PoE Mode 3

802.3af/at (Pins 1, 2+; 3, 6-)

802.3bt (Pins 1, 2+; 3, 6- and 4, 5+; 7, 8-)

54V / 1.1A PoE Adapter

PoE Out (Ports 2-5) 802.3af (Pins 1, 2+; 3, 6-)

Max. Power Consumption

(Excluding PoE Output)

Max PoE+ Wattage Per Port 15.4W

Total PoE Power Budget

(Enabled in Controller)

20W

46W

Voltage Range

802.3af

802.3at/bt

44 - 57V

50 - 57V

LEDs

System

RJ45 Data Ports

Status

PoE; Link/Speed/Activity

ESD/EMP Protection ± 16kV Air, ± 16kV Contact

Operating Temperature

46W PoE Output

25W PoE Output

-40 to 55° C (-40 to 131° F)

-40 to 65° C (-40 to 149° F)

Operating Humidity 5 to 95% Noncondensing

Certications CE, FCC, IC

Recommended PoE power source: US-8-150W (sold separately)

Recommended PoE power source: USW-Industrial (sold separately)

Recommended PoE power source: POE-50-60W-WH (sold separately)

(POE-50-60W-WH requires enabling injector mode in UniFi Controller)

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Failure to provide proper ventilation may

cause fire hazard. Keep at least 20 mm of clearance next

to the ventilation holes for adequate airflow.

WARNING: To reduce the risk of fire or electric shock, do

not expose this product to rain or moisture.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Do not use this product during an electrical

storm. Remote risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on

an individual basis, and, where applicable, specify arbitration instead of

jury trials or class actions.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced technician for help.

ISED Canada

CAN ICES-3(B)/NMB-3(B)

Australia and New Zealand

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2012/19/EU requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2012/19/EU verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

Español

La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en

el propio aparato y/o en su embalaje no deben eliminarse junto con otros

residuos urbanos no seleccionados. El símbolo indica que el producto

en cuestión debe separarse de los residuos domésticos convencionales

con vistas a su eliminación. Es responsabilidad suya desechar este y

cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos

de recogida que ponen a su disposición el gobierno y las autoridades

locales. Al desechar y reciclar correctamente estos aparatos estará

contribuyendo a evitar posibles consecuencias negativas para el medio

ambiente y la salud de las personas. Si desea obtener información más

detallada sobre la eliminación segura de su aparato usado, consulte a las

autoridades locales, al servicio de recogida y eliminación de residuos de su

zona o pregunte en la tienda donde adquirió el producto.

Français

La directive européenne 2012/19/UE exige que l’équipement sur lequel

est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté

avec les autres ordures ménagères. Ce symbole indique que le produit

doit être éliminé dans un circuit distinct de celui pour les déchets des

ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout

autre matériel électrique ou électronique par les moyens de collecte

indiqués par le gouvernement et les pouvoirs publics des collectivités

territoriales. L’élimination et le recyclage en bonne et due forme ont pour

but de lutter contre l’impact néfaste potentiel de ce type de produits

sur l’environnement et la santé publique. Pour plus d’informations sur le

mode d’élimination de votre ancien équipement, veuillez prendre contact

avec les pouvoirs publics locaux, le service de traitement des déchets, ou

l’endroit où vous avez acheté le produit.

Italiano

La direttiva europea 2012/19/UE richiede che le apparecchiature

contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non

siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica

che questo prodotto non deve essere smaltito insieme ai normali rifiuti

domestici. È responsabilità del proprietario smaltire sia questi prodotti sia

le altre apparecchiature elettriche ed elettroniche mediante le specifiche

strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il

corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze

potenzialmente negative per l’ambiente e per la salute dell’essere umano.

Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie

apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti

pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel

quale avete acquistato il prodotto.

La pagina sta caricando ...

Ubiquiti USW-Flex Guida Rapida

Marca: Ubiquiti

Modello: USW-Flex

Categoria: Switch di rete

Tipo: Guida Rapida

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti USW-Flex Quick start guide

Ubiquiti USW-Flex Guida Rapida

Ubiquiti USW-Flex Guida Rapida

in altre lingue

Documenti correlati

Altri documenti