Shindaiwa MTA-AHS-HD Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

MANUAL DE INSTRUCCIONES

MTA-AHS-HD

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS IN-

JURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LESRÈGLES DE

SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

ISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE

IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA

DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

ADVERTENCIA

LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES

PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SU-

FRIR LESIONES GRAVES.

1Cover

OPERATOR'S MANUAL

HEDGE TRIMMER ATTACHMENT

MTA-AHS-HD

ENGLISH

(Original instructions)

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Important information

2Important informati on

Please ensure that you read the operator's manual before using your product.

Introduction

This product was designed and manufactured to provide long life and on-the-job dependability.Read and understand

this manual you found in the package. You will find it easy to use and full of helpful operating tips and SAFETY mes-

sages.

Users of the product

You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

About your operator's manual

This manual contains necessary information about the assembly, operation, and maintenance of your product. Please

read it carefully and absorb its contents.

Always keep your manual in a place where it is readily accessible.

If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.

The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.

Loaning or assigning your product

When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.

Enquiries

Please contact your dealer for requests regarding information about your product, the purchase of consumables, re-

pairs, and other such enquiries.

Notices

The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

This product requires the assembly of some parts.

Please consult your dealer if anything is unclear or of concern.

IMPORTANT

This attachment is designed for use with the PAS-2620ES and M262S power sources. Use of this attachment with any

other product will cause premature gear case failure and void the warranty.

WARNING

Read rules for safe operation and instructions carefully. YAMABIKO provides Operator's Manuals with your original

PAS-2620ES and M262S. That manual and this manual must be read and understood for proper and safe operation, oth-

erwise serious personal injury may result.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a re-

placement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure.

For warranty service, find the nearest Authorised Service Dealer in our dealer locator map at www.echo australia.com.au/

en_au/finder, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au ,Briggs &

Stratton Australia Pty Ltd, Locked bag 5004, St Clair, NSW 2759.

3

Contents

For safe use of your product............................................................................................... 4

Warning notices............................................................................................................. 4

Other indicators ............................................................................................................. 4

Symbols.........................................................................................................................4

Location in which a safety decal is attached.................................................................. 5

Handling the product ..................................................................................................... 5

Description.......................................................................................................................... 9

Before you start ................................................................................................................10

Packing list .................................................................................................................. 10

Assembly ..................................................................................................................... 10

Adjusting cutting angle ................................................................................................ 11

Operation .......................................................................................................................... 13

Maintenance and care ...................................................................................................... 14

Maintenance and care ................................................................................................. 14

Storage ............................................................................................................................. 16

Specifications.................................................................................................................... 17

Declaration of conformity .................................................................................................. 18

UK Declaration of conformity ............................................................................................ 19

4

For safe use of your product

For safe use of yo ur product

Be careful to read this section before using your product.

The precautions described in this section contain important safety information. Please observe them carefully.

You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual Keep bystanders away 15 m

Wear eyes, ears and head

protection

Beware of high-temperature

areas

Wear foot protection and

gloves

Do not operate closer than 15

M from electrical hazards.

Emergency stop Beware of electric shocks

5

For safe use of your product

Location in which a safety decal is attached

The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

Handling the product

General precautions

1. Safety decal (Part number 890617-21661)

WARNING

Operator's manual

Be careful to read the operator's manual properly before using your product in order to ensure correct

operation.

Failure to do so could lead to an accident or serious injury.

Do not use the product for anything other than its intended purpose

You must not use the product for any purpose other than those described in the operator's manual.

To do so could lead to an accident or serious injury.

Do not modify the product

You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained

You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.

If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

Failure to do so could lead to an accident or serious injury.

6

For safe use of your product

Precautions for use

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure that you are pre-

pared.

First aid kit

Towels and wipes (to stop any bleeding)

Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help, the injury could

worsen.

WARNING

The area within a 15 m radius is a danger zone

The area within a 15 m radius of the product is a danger zone. Be careful to

observe the following precautions while working with the product.

Do not allow children and other people or pets to enter the danger zone.

If another person enters the danger zone, turn off the engine unit to stop the

blade

When approaching the operator, signal to him by, for example, throwing

twigs from outside the danger zone, and then check that engine has been

switched off and the blade has stopped moving.

Do not allow anyone to hold the material you are cutting.

Any contact with the cutter blade could cause serious injury.

Avoid hot surfaces

During operation, the complete unit, especially the drive shaft housing, power head, muffler and gear box

may become very hot, too hot to touch. Avoid contact during and immediately after operation.

You could burn yourself if you touch a high temperature component.

WARNING

Users of the product

The product should not be used by:

people who are tired

people who have taken alcohol

people who are on medication

people who are pregnant

people who are in poor physical condition

people who have not read the operator's manual

children

Failure to observe these instructions could lead to an accident.

Environment of use and operation

Do not use the product in places where there is no sure foothold, such as on steep slopes or after rainfall, as such

places are slippery and dangerous.

Do not operate the product at night or in dark places with poor visibility.

Do not work in odd positions or on ladders. Do not over reach.

A serious injury could result if you fall or slip, or fail to operate the product correctly.

For your own health and your safe and comfortable work, operate the machine within the air temperature range of -

5 oC to 40 oC.

Failure to observe these instructions could result in damage to your health.

7

For safe use of your product

Turn off the engine when moving around

When moving around in the situations described below, turn off the engine.

Moving to the place where you are working

Moving to another area while you are working

Leaving the place where you have been working

Failure to observe these precautions could cause burns or serious injury.

When transporting the product by car, empty the fuel tank, and secure the product firmly in place to prevent it from

moving around.

Travelling by car with fuel in the tank could lead to a fire.

Keep a firm grip

Hold the front and rear handles with both hands with thumbs and fingers tightly encircling the

handles.

Failure to observe these instructions could lead to an accident.

Vibration and cold

It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning, fol-

lowed by loss of colour and numbness in the fingers.

The following precautions are strongly recommended because the minimum exposure which might trigger the ailment

is unknown.

Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.

Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not

smoking.

Limit the number of hours of operation.

Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.

If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, consult

your physician before exposing yourself further to cold and vibration.

Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,

swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities may put

you at a high risk for developing a repetitive stress injury (RSI).

To reduce the risk of RSI, do the following:

Avoid using your wrist in a bent, extended or twisted position.

Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.

Do exercises to strengthen hand and arm muscles.

See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

Failure to observe these instructions could result in damage to your health.

Proper training

Do not permit operation without proper training and protective equipment.

Be thoroughly familiar with the controls and proper use of unit.

Know how to stop the unit and shut off the engine.

Never allow anyone to use the unit without proper instruction.

WARNING

8

For safe use of your product

Protective gear

WARNING

Wear protective gear

Always wear the following protective gear.

a Head protection (helmet): Protects the head

b Ear muffs or ear plugs: Protect the hearing

c Safety goggles: Protect the eyes

d Face shield: Protects the face

e Safety gloves: Protect the hands from cold and vibration

f Work clothes that fit (long sleeves, long trousers): Protect the body

g Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

h Shin guards: Protect the legs

Failure to observe these precautions could result in damage to your sight or hear-

ing, or lead to a serious injury.

When necessary, please use the protective gear below.

Dust mask: Protects the breathing apparatus

Bee net: To deal with attacks by bees

Wear proper clothing.

Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the unit.

Do not wear open toed footwear, or go bare-foot or barelegged. In certain situations, to-

tal face and head protection may be required.

Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

9

Description

1. Outer tube Part of the unit that provides a casing for

power transmission shaft.

2. Cutter assembly adjustment lever Provides secure

hand grip for adjusting cutting blade angle.

3. Latch lock Fixes the angle of the cutter.

4. Latch release Safety device to prevent the latch lock

from being released unexpectedly.

5. Gear housing assembly Gear housing contains drive

gears for transmitting power to cutting blades.

6. Cutter bar and cutter blades That part of the assembly

of cutter blade and shear plate together with any sup-

porting part, which performs the cutting action.

7. Blunt extension An extending blunt part of the cutting

device.

8. Blade cover When transporting or storing the product

always fit the blade cover.

9. Type and serial number

10

Before you start

Packing list

Assembly

Power head shaft/lower shaft assembly

1. Set power head/shaft assembly on a level surface.

2. Pull locator pin (A) out, and turn anticlockwise 1/4 turn to

lockout position.

3. Remove vinyl cap from attachment drive shaft.

4. Carefully fit attachment drive shaft assembly into coupler (B)

to decal assembly line (C), making sure that the inner lower

drive shaft engages into the square upper drive shaft socket.

5. Rotate locator pin (A) 1/4 turn clockwise to engage lower

shaft hole. Insure locator pin is fully engaged by twisting low-

er drive shaft. Locator pin should snap flush in coupler. Full

engagement will prevent further shaft rotation.

6. Secure lower shaft assembly to coupler by tightening clamp-

ing knob (D).

The following parts are packed separately in the packing box.

When you have unpacked the box, please check the parts that it contains.

Contact your dealer if anything is missing or broken.

1. Operation shaft

2. Blade cover

3. L-wrench

4. Spanner

5. Storage hook assembly

6. Operator's manual

WARNING

Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

NOTE

Lower bearing housing and head assembly must be in line with

the power source.

11

Before you start

7. To disassemble, reverse assembly instructions.

Adjusting cutting angle

Adjusting the hedge trimmer cutter assembly

1. Position the hedge trimmer on a flat, level surface with the

engine resting on the fuel tank guard. Make sure the blade

cover is in place on the blade.

2. With your right hand, grasp the outer tube near the handle.

With your left hand, grip the adjustment lever (A) on the cut-

ter assembly. With the index finger of your left hand, press

the latch release (B). With your left thumb, press the latch

lock.

3. While holding the latch release down, pivot the cutter assem-

bly using the adjustment lever until it is at the desired cutting

angle.

4. Release the latch lock (C) and the latch release. Make sure

the latch lock and the latch release return securely to the

straight ahead position.

5. Remove the blade cover (D) from the cutter blade. The en-

gine now may be started.

DANGER

Never adjust cutting assembly with engine running.

Failure to do so could lead to an injury or serious accident.

WARNING

Hedge trimmer blades are sharp. Always wear gloves when adjusting cutting assembly.

Wear heavy duty gloves when working with the hedge trimmer blades. When replacing the hedge trimmer blades

during a trimming task, ensure that the engine is switched off and that the blades have stopped.

Do not stand hedge trimmer on end when adjusting cutting angle, otherwise serious injury may result.

Gear case assembly becomes HOT during use. Always grip assembly at blade-adjustment handle when making cut-

ting angle adjustments, otherwise serious injury may result.

Failure to do so could lead to an injury or serious accident.

IMPORTANT

The latch release provides an interlock to help prevent inad-

vertent depression of the latch lock.

CAUTION

When installing and removing the blade cover from the

cutter blade, hold the handle under the blade cover.

Failure to observe these precautions could lead to injury.

12

Before you start

Cutter assembly position

The cutter assembly can be adjusted to ten different positions

ranging from 135° to 270° from the outer tube as shown. Al-

ways make sure the lock latch is securely locked after each

adjustment.

Shoulder strap

1. Hook the strap hook to the hanger on the outer tube.

2. Wear the shoulder strap so that the hook stays at your right

hand side.

3. Adjust the length of the shoulder strap so that you can hold

and operate the machine comfortably.

The shoulder harness is fitted with an emergency release

function. In case of emergency, pull up on the collar (A) to dis-

connect the machine from the strap.

IMPORTANT

 Make sure all hooks and adjustment devices are secure.

13

Operation

Hedge trimming

1. Hold trimmer firmly and squeeze throttle trigger to accelerate

engine.

2. Tilt trimmer so cutting teeth are angled slightly toward the

hedge or shrub and proceed to cut.

NOTE

This product is designed to cut shrubs and hedges with branches no larger than 6 mm in diameter.

When starting to trim, run the engine at full throttle. Cutting at less at than full speed can damage the clutch by allowing it to

slip. When you do not conduct trimming or cutting work, do not run the engine at full throttle.

Before operation a complete check of the unit must be performed;

Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

Never adjust blades when the engine is operating.

Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should not

be used.

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.

Always stop engine, disconnect the spark plug wire, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit.

Do not start or operate unit unless all guards and protective covers are properly assembled to unit.

Never reach into any opening while the engine is running. Moving parts may not be visible through openings.

Never remove hands from unit when blades are moving.

The engine continues running even when the blades have stopped due to an obstruction. If this occurs, stop the en-

gine, disconnect the spark plug wire and remove the obstruction.

14

Maintenance and care

15/20-Hour Maintenance

Gear case lubrication

1. Clean dirt from grease fitting (A).

2. Lubricate the cutter assembly gearbox by pumping one or

two strokes of lithium-base grease into the grease fitting us-

ing a lever-type grease gun.

Drive shaft lubrication

1. Loosen the gear case clamp bolt (A).

2. Remove the index bolt (B) from gear case (C).

3. Remove the outer tube (D) from the gear housing.

4. Pull the drive shaft (E) from the outer tube, and wipe clean.

Re-coat with a thin coating 10 to 20 g, of lithium base grease.

5. Slide the drive shaft back into the outer tube, being careful

not to get dirt on the drive shaft.

6. Align the screw hole in gear case with the locating hole in

outer tube, install and tighten index bolt, and tighten gear

case clamp bolt.

Care for cutting blades

Lubricating blades (Every 4 hours of operation)

Apply a few drops of oil the each bolt slots (A) at the bottom of

blades.

Cleaning blades (After each use)

Remove gummy residue from blades with a 50 : 50 mixture of

kerosene (paraffin) and machine oil.

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect the spark plug wire, and make sure all moving parts have come to a com-

plete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.

Wear gloves to protect hands from sharp edges and hot surfaces.

If you have any questions or problems, please contact your dealer.

CAUTION

Over lubricating can cause the gear case to operate

sluggishly and can cause grease to leak out.

CAUTION

Wear gloves to protect hands from sharp blades.

Failure to observe these precautions could lead to injury.

15

Maintenance and care

Cutter blade adjustment

Standard blades require no periodic adjustments. Make sure all

blade bolts (A) are tight and in good condition.

16

Storage

Storage hook installation

1. Insert small end of hook into locating hole on attachment

shaft.

2. Slide plastic cap onto end of attachment shaft.

17

Specifications

These specifications are subject to change without notice.

MTA-AHS-HD

External dimensions:

Length x Width x Height mm 966 × 122 × 95

Masses kg 2.1

Cutting attachment:

Type Dual action, double sided blade

Cutting length mm 536

Pitch mm 35

Height mm 21

Gear ratio and lubrication: 4.60 reduction and good quality lithium grease

Vibration levels: (ISO 10517) ahv,eq

Front handle / Rear handle m/s² 7.8 / 6.9

m/s² 8.1 / 6,5 (with MTA-3EXT)

Uncertainty: K m/s² 5.0

Sound pressure level: (ISO 10517) LpAd(=LpAeq +KpA)dB (A)97.0

Uncertainty: KpA dB (A) 2.5

Sound power level: (ISO 10517) LWAd(=LWAeq +KWA) dB (A) 108.0

Uncertainty: KWA dB (A) 2.5

Applicable model PAS-2620ES and M262S

18

Declaration of conformity

The undersigned manufacturer:

YAMABIKO CORPORATION

1-7-2 Suehirocho

Ohme, Tokyo 198-8760

JAPAN

This declaration of conformity is issued under the sole responsibility of the manufacturer.

declares that the hereunder specified new unit:

PRO ATTACHMENT SERIES

Type: PAS-2620ES + MTA-AHS-HD

Multi-tool System

Type: M262S + MTA-AHS-HD

complies with:

* the requirements of Directive 2006/42/EC (use of harmonized standard EN ISO 10517: 2019)

* the requirements of Directive 2014/30/EU (use of harmonized standard EN ISO 14982: 2009, EN 55012: 2007+A1:

2009)

* the requirements of Directive 2011/65/EU (use of harmonized standard EN IEC 63000: 2018)

* the requirements of Directive 2000/14/EC

Conformity assessment procedure followed ANNEX V

Measured sound power level :106 dB(A)

Guaranteed sound power level :109 dB(A)

Serial Number U65940001001 to U65940100000

Tokyo, October 18th, 2022

YAMABIKO CORPORATION

The authorized representative in Europe who is authorized to

compile the technical file.

Company: CERTIFICATION EXPERTS B.V.

Address: Amerlandseweg 7, 3621 ZC Breukelen, The Nether-

lands

Hisashi Kobayashi Mr. Richard Glaser

General Manager

Quality Assurance Dept.

La pagina si sta caricando...

Shindaiwa MTA-AHS-HD Manuale utente

Shindaiwa MTA-AHS-HD Manuale utente

in altre lingue

Documenti correlati