Hotpoint LFF 8M122 X AUS Guida utente
- Categoria
- Lavastoviglie
- Tipo
- Guida utente
Questo manuale è adatto anche per
LFF 8M122
EN
English
Operating instructions
DISHWASHER - Contents
Operating instructions,1
Precautions and advice, 2-3
Product Data, 4
Installation, 5-6
Description of the appliance, 7
Refined salt and rinse aid, 8
Loading the racks, 9-10
Detergent and dishwasher use, 11
Wash cycles, 12
Special wash cycles and options, 13
Care and maintenance, 14
Troubleshooting, 15
Assistance, 16
EN
2
Precautions, advice and
Assistance
EN
Precautions and advice
This appliance was designed and
manufactured in compliance with international
safety standards. The following information
has been provided for safety reasons and
should be read carefully.
Keep this instruction manual in a safe place
for future reference. If the appliance is sold,
given away or moved, make sure the manual
is kept with the machine.
Read the instructions carefully, as they
include important information on safe
installation, use and maintenance.
This appliance was designed for domestic
use or similar applications, for example:
- farmhouses;
- use by guests in hotels, motels and other
residential settings;
- bed & breakfasts.
Remove the appliance from all packaging
and make sure it was not damaged during
transportation. If it was damaged, contact
the retailer and do not proceed any further
with the installation process.
General safety
• This appliance should not be operated
by children younger than 8 years, people
with reduced physical, sensory or mental
capacities, or inexperienced people
who are not familiar with the product,
unless they are given close supervision
or instructions on how to use it safely and
are made aware by a responsible person
of the dangers its use might entail.
• Children must not play with the appliance.
• It is the user's responsibility to clean and
maintain the appliance. Children should
never clean or maintain it unless they are
given supervision.
• The appliance was designed for domestic
use inside the home and is not intended
for commercial or industrial use.
• The appliance must be used to wash
domestic crockery in accordance with the
instructions in this manual.
• The appliance must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the machine
exposed to rain and storms.
• Do not touch the appliance when barefoot.
• When unplugging the appliance always
pull the plug from the mains socket. Do
not pull on the cable.
• The water supply tap must be shut off
and the plug should be removed from
the electrical socket at the end of every
cycle and before cleaning the appliance
or carrying out any maintenance work.
• The maximum number of place settings is
shown in the product sheet.
• If the appliance breaks down, do not under
any circumstances touch the internal parts
in an attempt to perform the repair work
yourself.
• Do not lean or sit on the open door: this
may cause the appliance to overturn.
• The door should not be left open as it may
create a dangerous obstacle.
• WARNING: Some dishwasher detergents
are strongly alkaline. They can be
extremely dangerous if swallowed. Avoid
contact with the skin and eyes and keep
children away from the dishwasher when
the door is open. Check that the detergent
receptacle is empty after completion of the
wash cycle.
• The packaging material should not be
used as a toy.
• Knives and other utensils with sharp
edges must be placed either with the
points/blades facing downwards in the
cutlery basket or horizontally on the tip-up
compartments or in the tray/third basket,
if available.
Disposal
• To dispose of any packaging materials,
follow local legislation so that the
packagings may be reused.
• The European Directive 2012/19/EU
relating to Waste Electrical and Electronic
Equipment (WEEE) states that household
appliances should not be disposed of
using the normal solid urban waste cycle.
Exhausted appliances should be collected
separately in order to optimise the cost of
reusing and recycling the materials inside
the machine, while preventing potential
damage to the atmosphere and public
health. The crossed-out dustbin symbol
shown on all products reminds the owners
of their obligations regarding separated
waste collection.
For further information relating to the correct
disposal of household appliances, owners
may contact the relevant public authority
or the local appliance dealer.
EN
3
Saving energy and respecting the
environment
Saving water and energy
• Only begin a wash cycle when the
dishwasher is full. While waiting for the
dishwasher to be filled, prevent unpleasant
odours with the Soak cycle
(if available, see
Wash Cycles).
• Select a wash cycle that is suited to the
type of crockery and to the soil level using
the Table of Wash Cycles:
- For dishes with a normal soil level, use
the Eco wash cycle, which guarantees low
energy and water consumption levels.
- If the load is smaller than usual activate
the Half Load option
(see Special wash cycles
and options, if available).
• If your electricity supply contract gives
details of electricity-saving time bands, run
the wash cycles when electricity prices are
lower. The Delayed Start option can help
you organise the wash cycles accordingly
(see Special wash cycles and options, if available).
EN
4
Product Fiche
Brand
ARISTON
Model
LFF 8M122
Rated capacity in standard place settings (1)
14
Energy Star Rating
3.5
Comparative Energy Consumption (kWh/year), CEC
263.0
Energy Total (kWh), E
t
0.672
Average measured Standby Power (W), P
s
2.29
Primary Total Water Volume (L)
9.7
Water Star Rating
5.5
Noise in dB(A) Re 1pW
42
Built-in model
No
NOTES
1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally soiled
tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard cleaning cycle
corresponds to the Normal cycle.
Product Data (product fiche)
EN
5
Installation
* Only available in selected models.
If the appliance must be moved at any time, keep it in
an upright position; if absolutely necessary, it may be tilted
onto its back.
Connecting the water supply
Adaptation of the water supply for installation should only
be performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards
the right or the left in order to achieve the best possible
installation.
Make sure the dishwasher does not bend or squash the
hoses.
Connecting the water inlet hose
• To a 3/4” gas cold or hot water connection point (max.
60°C).
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn off the
tap.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician
(see Assistance)
.
The water pressure must be within the values indicated
in the Technical Data table - otherwise the dishwasher may
be function properly.
Make sure the hose is not bent or compressed.
Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum
diameter of 2 cm. (A)
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher
rests.
Before connecting the water outlet hose to the sink drain,
remove the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Some models are also equipped with the supplementary
safety device New Acqua Stop*, which guarantees anti-
flooding protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut
as it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• The socket is earthed and complies with current
regulations;
• the socket can withstand the maximum load of the
appliance as shown on the data plate located on the inside
of the door
(see chapter Description of the appliance);
• The power supply voltage falls within the values indicated
on the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to
replace the plug (
see Assistance
). Do not use extension
cables or multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced
by the manufacturer or its authorised Technical Assistance
Service in order to prevent all potential hazards.
(See
Assistance)
The Company shall not be held responsible for any
incidents, if these regulations are not observed.
Positioning and levelling
1. Position the dishwasher on a level sturdy floor. If the floor is
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move
or cause vibrations and noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive
transparent strip* under the wooden shelf in order to protect
it from any condensation which may form.
3. Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop*
(see the
Assembly instruction sheet)
.
4*. To adjust the height of the rear foot, turn the red
hexagonal bushing on the lower central part at the front of the
dishwasher using a hexagonal spanner with an opening of 8
mm. Turn the spanner in a clockwise direction to increase the
height and in an anticlockwise direction to decrease it.
(see
Building-in instruction sheet attached to the documentation)
MIN 40 cm
MAX 80 cm
EN
6
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EU Waste Electrical
and Electronic Equipment (WEEE)
* Only available in selected models.
Avvertenze per il primo lavaggio
Dopo l’installazione, rimuovere i tamponi posizionati sui cesti e
gli elastici di trattenimento sul cesto superiore
(dove presenti).
Impostazioni addolcitore acqua
Prima di avviare il primo lavaggio, impostare il livello di
durezza dell’acqua di rete.
(vedi capitolo Brillantante e sale
rigenerante)
Il primo caricamento del serbatoio dell’addolcitore deve avve-
nire con acqua, poi introdurre circa 1 Kg. di sale; è normale
che l’acqua fuoriesca.
Far partire un ciclo di lavaggio subito dopo.
Usare solo sale specifico per lavastoviglie.
Dopo il caricamento la spia MANCANZA SALE* si spegne.
Il mancato riempimento del contenitore del sale, può
provocare il danneggiamento del dolcificatore dell’acqua e
dell’elemento riscaldante.
La macchina, è dotata di segnali acustici/toni
(secondo il
modello d lavastoviglie
) che avvisano dell’avvenuto comando:
accensione, fine ciclo ecc..
I simboli/spie/led luminosi presenti sul pannello comandi/
display, possono variare di colore, pulsare o essere a luce
fissa.
(secondo il modello di lavastoviglie)
.
Il display*, visualizza informazioni utili relative al tipo di
ciclo impostato, alla fase di lavaggio/asciugatura, al tempo
residuo, alla temperatura ecc... ecc...
EN
7
Overall view
Description of the
appliance
***Only in completely built-in models. * Only available in selected models.
Control panel
The number and type of wash cycles and options may vary depending on the dishwasher model.
Start/Pause
button and
indicator lights
Button and
indicator light
On-Off/Reset
Extra Drying option button
Zone Wash option button
Delayed Start
buttons
Multi-functional Tablets
option button (Tabs)
Wash-Cycle Selection buttons
Short time Option button
Wash-cycle indicator lights
Wash-cycle indicator lights
Zone Wash indicator lights
Low Rinse-Aid indicator light
Low Salt indicator light
Blocked Filter indicator light
Extra Drying indicator light
Multi-Functional Tablets indicator light (Tabs)
Washing and Drying indicator lights
Tap Shut-Off indicator light
Delayed Start indicator light
Short Time indicator light
Remaining Time indicator
Display
1. Upper rack
2. Top sprayer arm
3. Tip-up compartments
4. Rack height adjuster
5. Lower rack
6. Bottom sprayer arm
7. Washing filter
8. Salt dispenser
9. Detergent and rinse aid dispenser
10. Data plate
11. Control panel***
EN
8
M
A
X
Only use products which have been specifically designed
for dishwashers. Do not use table salt or industrial salt.
Follow the instructions given on the packaging.
If you are using a multi-function product, we recommend
that you add salt in any case, especially if the water is hard
or very hard.
(Follow the instructions given on the packaging.)
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID* indicator lights will remain lit.
Measuring out the refined salt
The use of salt prevents the formation of LIMESCALE on the
dishes and on the machine's functional components.
• It is important that the salt dispenser be never empty.
• It is important to set the water hardness.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• When the LOW RINSE AID indicator light in the control panel
is lit *;
• When the green float* on the cap of the salt dispenser is no
longer visible.
• See autonomy in the water hardness table.
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. Only the first time you do this: fill the water
dispenser up to the edge.
3. Position the funnel
(see figure)
and
fill the salt container right up to its edge
(approximately 1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on.
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
Whenever you need to add salt, we recommend carrying
out the procedure before the washing cycle is started.
Setting the water hardness
For perfect water softener operation, it is essential that the
adjustment be based on the water hardness in your house. Ask
your local water supplier for this information. The factory setting
is for medium water hardness.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Press and hold the START/PAUSE button for 5 seconds.
• Switch it on using the On/Off button
• Access the adjustment menu - the salt indicator light is lit.
• Select the desired level (1 to 5* max. based on the dishwasher
model) using the ECO button
(see Table on water hardness).
• Switch it off using the On/Off button
• Setting is complete!
Refined salt and
rinse aid
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)
Measuring out the rinse aid
Rinse aid makes dish DRYING easier. The rinse aid dispenser
should be filled:
• When the LOW RINSE AID indicator light on the panel/display
is lit *;
• When the dark optical indicator* on the dispenser door “D”
becomes transparent.
1. Open the dispenser “D” by pressing and pulling up the tab
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch in the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may want to adjust the quantity of rinse aid used.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Press the START/PAUSE button three times
• Switch it on using the On/Off button
• Access the adjustment menu - the rinse-aid indicator light is lit .
• Select the level of rinse aid supply using the ECO cycle button.
• Switch it off using the On/Off button
• Setting is complete!
If the rinse aid level is set to ZERO, the rinse aid will not be
supplied and the low rinse aid indicator light will not be lit if you
run out of it.
A maximum of 4 levels can be set according to the dishwasher
model. The factory setting is for a medium level.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
Water Hardness Table
Average autonomy
salt dispenser with 1
wash cycle per day
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1.1 - 2 5 months
3 12 - 17 21 - 30 2.1 - 3 3 months
4 17 - 34 31 - 60 3.1 - 6 2 months
5*
34 - 50 61 - 90 6.1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use of salt.
A setting of 5 may increase cycle duration.
* Only available in selected models.
EN
9
Loading the racks
Tips
Before loading the racks, remove all food residues from the
crockery and empty liquids from glasses and containers. No
preventive rinsing is needed under running water.
Arrange the crockery so that it is held in place firmly and does
not tip over; and arrange the containers with the openings facing
downwards and the concave/convex parts placed obliquely,
thus allowing the water to reach every surface and flow freely.
Make sure that the lids, handles, trays and frying pans do not
prevent the sprayer arms from rotating. Place any small items
in the cutlery basket.
Since plastic dishes and non-stick frying pans usually retain more
water drops, their drying will be not so good as that of ceramic
or stainless-steel dishes.
Lightweight items such as plastic containers should be placed
in the upper rack and arranged so that they cannot move.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack
The lower rack can hold pans, lids, dishes, salad bowls, cutlery
etc. Large plates and lids should ideally be placed at the sides.
Very soiled dishes and pans should be placed in the lower rack
because in this sector the water sprays are stronger and allow
a higher washing performance.
Several dishwasher models are fitted with tip-up sectors*.
They can be used in a vertical position when arranging dishes
or in a horizontal position (lower) to load pans and salad bowls
easily.
Cutlery basket
The modular basket is equipped with top grilles for improved
cutlery arrangement. The cutlery basket should be positioned
only at the front of the lower rack
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards or they
must be positioned horizontally in the tip-up compartments on
the upper rack
Upper rack
Load this rack with delicate and lightweight crockery such as
glasses, cups, saucers and shallow salad bowls.
Several dishwasher models are fitted with tip-up sectors*.
They can be used in a vertical position when arranging tea/
dessert saucers or in a lower position to load bowls and food
containers.
*Only available in selected models with different numbers and
positions.
EN
10
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower position.
The height of the upper rack should be adjusted WHEN THE
RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
If the rack is equipped with a Lift-Up device*
(see figure)
, lift
it up by holding its sides. To restore the lower position, press
the levers (A) at the sides of the rack and follow the rack down.
Unsuitable crockery
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique
crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high
temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of
glass (e.g. crystal objects) can become opaque after a number
of wash cycles too.
Damage to glass and crockery
Caused by:
• Type of glass and glass production process.
• Chemical composition of detergent.
• Water temperature of rinse cycle.
Tips:
• Only use glasses and porcelain guaranteed by the
manufacturer as dishwasher safe.
• Use a delicate detergent suitable for crockery.
• Collect glasses and cutlery from the dishwasher as soon as
the wash cycle is over.
The upper rack can be adjusted for height based on requirements:
high position to place bulky crockery in the lower rack and low
position to make the most of the tip-up compartments/sectors
by creating more space upwards.
* Only available in selected models.
Tip-up compartments with adjustable position
The side tip-up compartments can be positioned at three
different heights to optimize the arrangement of crockery inside
the rack.
Wine glasses can be placed safely in
the tip-up compartments by inserting
the stem of each glass into the
corresponding slots.
For optimum drying results incline
the tip-up compartments more. To
change the inclination, pull up the
tip-up compartment, slide it slightly
and position it as you wish.
Cutlery tray*
Some dishwasher models are fitted with a sliding tray which
can be used to hold serving utensils or small cups. For optimum
washing performance avoid positioning bulky crockery directly
below the tray. The cutlery tray can be removed
(see Figure).
EN
11
Start-up and use
* Only available in selected models.
Starting the dishwasher
1. Turn the water tap on.
2. Press the ON/OFF button: The ON/OFF indicator light and
the display light up.
3. Open the door and pour in a suitable amount of detergent
(see below).
4. Load the racks
(see Loading the racks)
and shut the door.
5. Select the wash cycle in accordance with the type of crockery
and its soil level
(see Table of wash cycles)
by pressing the
wash-cycle selection buttons.
6. Select the wash options*
(see adjacent information).
7. Start the cycle by pressing the Start/Pause button: The wash
indicator light comes on and the time left to the end of the cycle
appears on the display.
8. At the end of the cycle, the display shows END. Switch off the
appliance by pressing the ON/OFF button, shut off the water tap
and unplug the appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery in order
to avoid burns. Unload the racks, beginning with the lower level.
- The machine will switch off automatically during long
periods of inactivity in order to minimise electricity
consumption.
AUTO WASH CYCLES*:some dishwasher models are
equipped with a special sensor which can be used to assess
the level of soiling and automatically select the most efficient
and economical wash cycle accordingly. The duration of the
auto wash cycles may vary due to the operation of the sensor.
Changing a wash cycle in progress
If a mistake was made in the wash cycle selection process, it is
possible to change the cycle provided that it has only just begun:
once the wash cycle has started, in order to change the wash
cycle switch off the machine by pressing and holding the ON/
OFF/Reset button. Switch it back on using the same button and
select the desired wash cycle and options.
Adding extra crockery
Press the Start/Pause button and open the door, taking care to
avoid the escaping steam, and place the crockery inside the
dishwasher. Press the Start/Pause button: The cycle will start
again after a long beep has been emitted.
If the delayed start has been set, at the end of the countdown
the wash cycle will not start. It will stay in Pause mode.
Press the Start/Pause button to pause the machine; the wash
cycle is stopped.
At this stage it is not possible to change the wash cycle.
Accidental interruptions
If the door is opened during the wash cycle or there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply is restored.
Measuring out the detergent
A good wash result also depends on the correct
amount of detergent being used. Exceeding the stated
amount does not result in a more effective wash and
increases environmental pollution.
Based on how soiled the items are, the amount can be
adjusted to individual cases using powder or liquid
detergent.
In the case of normally soiled items, use approximately
either 35 gr (powder detergent) or 35 ml (liquid detergent).
If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce
the amount of detergent used accordingly.
For good washing results also follow the instructions shown
on the detergent box.
For further questions please ask the detergent producers.
To open the detergent dispenser use the opening device “A”.
Introduce the detergent into the dry dispenser “B” only.
Place the amount of detergent for pre-washing directly
inside the tub.
1. When measuring out the detergent refer to the Table of wash
cycles to add the proper quantity. Compartment B comprises
a level showing the maximum quantity of liquid or powder
detergent that can be added to each cycle.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TABS
option, because it adjusts the cycle so that the best washing
and drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam residues
remaining in the machine after the cycle has ended.
To achieve the best washing and drying results, the
combined use of detergent, rinse aid liquid and refined salt
is required.
We recommend using detergents that do not contain
phosphates or chlorine, as these products are harmful to
the environment.
EN
12
Wash cycles
Wash cycle
Wash cycle
which
include
drying
Options
Approximate
duration of wash
cycles
Water
consumption
(l/cycle)
Energy
consumption
(KWh/cycle)
Normal *
Yes
Delayed start – Tabs –
Extra Dry
03:10’ 9,7 0,672
Auto 65° Yes
Delayed start – Tabs – Extra
Dry – Short Time – Zone wash
02:00’ - 03:10’ 14,0 - 15,5 1,50 - 1,80
Auto 55° Yes
Delayed start – Tabs – Extra
Dry – Short Time – Zone wash
01:30’ - 02:30’ 14,5 – 16,0 1,20 - 1,35
Auto 50° No Delayed start – Tabs 00:40’ - 01:20’ 13,0 - 14,5 1,15- 1,25
Duo Wash Yes
Delayed start – Tabs –
Extra Dry – Short Time
02:00’ 18,0 1,30
Delicate Yes
Delayed start – Tabs –
Extra Dry
01:40’ 11,0 1,10
Express 30’ No Delayed start – Tabs 00:30’ 9,0 0,50
Soak No Delayed start 00:12’ 4,5 0,01
Instructions on wash-cycle selection and detergent dosage
1. The NORMAL wash cycle is the standard cycle to which the energy label data refers. It can be used to wash crockery with a
normal soil level and is the most efficient cycle in terms of energy and water consumption for this type of crockery.
Open the door at end of programme by 50mm to assist in drying. Add detergent amounts for cycle: 29 gr/ml + 6 gr/ml** – 1 Tab
(**Quantity of pre-washing detergent)
2. Heavily soiled dishes and pans (not to be used for delicate items). 35 gr/ml – 1 Tab
3. Normally soiled pans and dishes. 29 gr/ml + 6 gr/ml** – 1 Tab
4. Limited quantity of daily soiling (ideal for 4 place settings) 25 gr/ml – 1 Tab
5. Wash spread over the two racks: delicate for crystal and glasses on the upper rack and heavy duty for the pans on the lower
rack. 35 gr/ml – 1 Tab
6. Cycle for delicate items, which are more sensitive to high temperatures 35 gr/ml – 1 Tab
7. Fast cycle to be used for slightly dirty dishes (ideal for 2 place settings) 25 gr/ml – 1 Tab
8. Pre-wash while awaiting completion of the load with the dishes from the next meal. No detergent.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W.
Notes: Optimum performance levels when using the “Fast" and "Express 30’” cycles can be achieved by respecting the specified
number of place settings.
To reduce consumption even further, only run the dishwasher when it is full.
* The Normal wash cycle adheres to the regulation standard AS/NZS 2007. Although it has a longer duration than other wash cycles
it uses less energy and is less harmful to the environment.
Note for Test Laboratories: for information on comparative EN testing conditions, please send an email to the following address:
The number and type of wash cycles and options may vary depending on the dishwasher model.
EN
13
Extra drying
To improve the dryness level of the crockery, press
the EXTRA DRYING button and the symbol will light up. If it
is pressed again, the option will be deselected.
A higher temperature during the final rinsing and a longer
drying phase improve the dryness level.
The EXTRA DRYING option increases the duration of
the wash cycle.
Delayed start
It is possible to delay the start time of the cycle for
a period of time between 1 and 24 hours:
1. Select the desired wash cycle and any other options
required, press the DELAYED START button. The relevant
symbol starts flashing. Use the buttons + and - to select when
the wash cycle will start (h01, h02 etc.)
2. Confirm with the START/PAUSE button. The symbol stops
flashing and the countdown begins.
3. Once this time has elapsed, the DELAYED START symbol
switches off and the wash cycle begins.
To deselect the DELAYED START option, press the DELAYED
START button until the text OFF appears.
The Delayed Start function cannot be set once a wash
cycle has been started.
Wash options*
The OPTIONS may only be set, changed or reset after
the wash cycle has been selected and before the Start/
Pause button has been pressed.
Only the options which are compatible with the type of wash
cycle set may be selected. If an option is not compatible
with the selected wash cycle
(see Table of wash cycles)
, the
corresponding symbol flashes rapidly 3 times.
If an option is selected which is not compatible with another
(previously selected) option, it will flash 3 times and switch
off, while the most recently selected option will remain active.
To deselect an option which has been set by mistake, press
the corresponding button again.
Multi-functional tablets* (Tabs)
This option optimises washing and drying results.
When using multi-functional tablets, press the MULTI-
FUNCTIONAL TABLETS button; the corresponding symbol
will light up. If the button is pressed again, the option will
be deselected.
The “Multi-functional tablets” option results in a
longer wash cycle.
The use of tablets is only recommended for models
having this option and it is not recommended with wash
cycles which do not specify the use of multi-functional
tablets.
Special wash cycles and Options
Short Time option
This option can be used to reduce the duration of
the main wash cycles while maintaining the same
washing and drying performance levels.
After selecting the wash cycle, press the Short Time option
button;
To deselect the option, press the same button again.
* Only available in selected models.
Zone Wash
This option makes it possible to carry out the wash
cycle in the selected rack only. Select the wash cycle and
then press the ZONE WASH button: the selected rack lights
up and the wash cycle starts in the selected rack only. Press
the button again to deselect the option.
The option is available with the following wash cycles:
Intensive and Normal.
Select the option and the Intensive cycle to start the
ULTRAINTENSIVE ZONE washing. This wash cycle is ideal
for very soiled mixed loads, e.g. pans and saucepans,
dishes with heavy encrustation or difficult-to-clean crockery
(grater, vegetable mill, dirty cutlery). The spraying pressure is
stronger and the washing temperature higher, thus ensuring
optimum handling of stubborn stains.
Select the option and the Normal cycle to start the SAVING
ZONE washing. This function makes it possible to reduce
water and energy consumption, thus achieving excellent
washing and drying results. Cycle duration is longer.
Remember to load the crockery in the selected rack only
EN
14
Care and maintenance
Shutting off the water and electricity
supplies
• Turn off the water tap after every wash cycle to avoid leaks.
• Always unplug the appliance when cleaning it and when
performing maintenance work.
Cleaning the dishwasher
• The external surfaces of the machine and the control panel
can be cleaned using a non-abrasive cloth which has been
dampened with water. Do not use solvents or abrasive
products.
• Any marks on the inside of the appliance may be removed
using a cloth dampened with water and a little vinegar.
Preventing unpleasant odours
• Always keep the door of the appliance ajar in order to avoid
moisture from forming and being trapped inside the machine.
• Clean the seals around the door and detergent dispensers
regularly using a damp sponge. This will avoid food becoming
trapped in the seals, which is the main cause behind the
formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that you check the arms from time to time and
clean them with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer arm,
turn the plastic locking ring in an
anti-clockwise direction. The upper
sprayer arm should be replaced
so that the side with the greater
number of holes is facing upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free
of impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked
and damage the dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter and
clean it carefully under running water.
- Re-place the filter and screw the water hose back into position.
Cleaning the filters
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the water.
They should be cleaned if you wish to achieve the best results
in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters or if the
filter is loose.
• After several washes, check the filter assembly and if necessary
clean it thoroughly under running water, using a non-metallic
brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction and
pull it out
(fig. 1).
2. Remove the cup filter B by exerting a slight pressure on the
side flaps
(fig. 2);
3. Slide out the stainless-steel plate filter A.
(fig. 3).
4. Inspect the trap and remove any food residues. NEVER
REMOVE the wash-cycle pump protection
(black detail) (fig.4).
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
Leaving the machine unused for extended
periods
• Disconnect the appliance from the electricity supply and shut
off the water tap.
• Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher is
empty.
* Only available in selected models.
EN
15
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
* Only available in selected models.
Problem: Possible causes / Solutions:
The dishwasher does not start or cannot
be controlled.
• Switch off the appliance by pressing the ON/OFF button, switch it back
on after approximately one minute and reset the cycle.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close.
• The lock was released. Strongly push the door until a “clacking” noise
is heard.
No water drains from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
streaked or have a bluish tinge.
• The rinse aid dosage is too high.
The crockery has not been dried
properly.
• A wash cycle without a drying cycle has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid
and salt).
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
The dishes are not clean. • The racks are overloaded (see Loading the racks).
• The crockery has not been arranged properly.
• The sprayer arms cannot rotate freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-Up and Use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
• Switch off the appliance by pressing the ON/OFF button. Shut off the
water tap to eliminate the risk of flooding and remove the plug from the
electrical socket.
Make sure the water inlet filter has not become blocked by impurities
(see “Care and maintenance” chapter).
The dishwasher does not take any
water in - Tap shut-off alarm
(indicator light ON/OFF ashing; H2O and
tap symbol displayed; F 6 appears after a
few seconds).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken
when the beeps sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and
switch the appliance back on after a few seconds by pressing the same
button. Re-program the appliance and restart the wash cycle.
Clogged lter alarm
The “lter” symbol on the display will light
up.
• Make sure the wash cycle has ended, open the dishwasher door
and clean the cup filter and stainless-steel filter (see “Care and
maintenance” chapter). The “blocked filter” symbol will go off when the
following cycle starts.
EN
16
195125822.00 - NC
05/2014 jk - Xerox Fabriano
Indesit Company Spa
Viale Aristide Merloni 47
60044 Fabriano (AN)
Italy
Assistance
Before contacting Assistance:
• Check whether the problem can be resolved using the Troubleshooting guide
(see Troubleshooting).
• Restart the programme to check whether the problem has ceased to exist.
• If the problem persists, contact the Authorised Technical Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• The type of malfunction.
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the appliance data plate
(see Description of the appliance)
.
ARISTON
PRIORITY SERVICE
If you are not completely satisfied
with your appliance or require
service call:
Australia
Phone: 1300 815 589
New Zealand
Phone: (09) 306 1020
AUSTRALIA
ARISIT PTY LIMITED
40-44 Mark Anthony Drive, Dandenong South,
VIC 3175, Australia
Fax: Service & Sales (03) 9768 0838
Email: [email protected]
GENUINE ACCESSORIES
& SPARE PARTS
A wide range of genuine
accessories are available for
your appliance call:
Australia
Phone: 03 9768 0888
New Zealand
Phone: (09) 306 1020
NEW ZEALAND
ARISIT PTY LIMITED
PO Box 68-140 Newton, Auckland
1145, New Zealand
Fax: (09) 302 0077 -
Email: [email protected]
Assistances
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Hotpoint LFF 8M122 X AUS Guida utente
- Categoria
- Lavastoviglie
- Tipo
- Guida utente
- Questo manuale è adatto anche per
in altre lingue
- English: Hotpoint LFF 8M122 X AUS User guide
Documenti correlati
Altri documenti
-
Whirlpool DFG 26M1 A S IT Guida utente
-
Indesit DFG 26M1 A S IT Guida utente
-
HOTPOINT/ARISTON LTF 11M113 7L EU Guida utente
-
Hotpoint-Ariston LFD 11M132 Manuale del proprietario
-
Whirlpool DFG 15B1 S IT Guida utente
-
HOTPOINT/ARISTON LFB 5B019 A EU Guida utente
-
-
-
Franke FDW 613 E5P F Guida utente
-