Bose AM301726 Manuale utente

Framingham, MA 01701-9168 USA

AM301726 Rev.00

Owner’s Guide

Brugervejledning

Bedienungsanleitung

Guía de usario

Notice d’utilitsation

Manuale di istruzioni

Gebruiksaanwijzing

Bruksanvisningen

LIFESTYLE

®

VS-2

VIDEO ENHANCER

LIFESTYLE

®

VS–2 VIDEO ENHANCER

00_Cover_Lasik.fm Page 1 Thursday, October 26, 2006 11:47 AM

2

English

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions – for future reference.

3. Heed all warnings – on the product and in the owner’s guide.

4. Follow all instructions.

5. Do not use this apparatus near water – Do not use this product near a bathtub,

washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, or

anywhere else that water or moisture are present.

6. Clean only with a dry cloth – and as directed by Bose Corporation. Unplug this

product from the wall outlet before cleaning.

7. Do not block any ventilation openings. Install in accordance with the manu-

facturer’s instructions – To ensure reliable operation of the product and to protect it

from overheating, put the product in a position and location that will not interfere with

its proper ventilation. For example, do not place the product on a bed, sofa, or similar

surface that may block the ventilation openings. Do not put it in a built-in system,

such as a bookcase or a cabinet, that may keep air from flowing through its ventila

-

tion openings.

8. Do not install near any heat sources, such as radiators, heat registers, stoves

or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-

type plug has two blades and a third grounding prong. The wider blade or

third prong are provided for your safety. If the provided plug does not fit in

your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time – to prevent damage to this product.

14. Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the appa

-

ratus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped – Do not attempt to service this product yourself.

Opening or removing covers may expose you to dangerous voltages or other haz

-

ards. Please call Bose to be referred to an authorized service center near you.

15. To prevent risk of fire or electric shock, avoid overloading wall outlets, exten-

sion cords, or integral convenience receptacles.

16. Do not let objects or liquids enter the product – as they may touch dangerous

voltage points or short-out parts that could result in a fire or electric shock.

17. See product enclosure bottom for safety-related markings.

Information about products that generate electrical noise

If applicable, this equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, this is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or televi

-

sion reception, which can be determined by turning the equipment off and on, you are

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a different circuit than the one to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Unauthorized modification of the receiver or radio remote control could void the user’s

authority to operate this equipment.

This product complies with the Canadian ICES-003 Class B specifications.

00_LasikOG.book Page 2 Thursday, October 26, 2006 1:23 PM

3

English

Please read this installation guide

Please take the time to follow this installation guide carefully. It will help you set

up and operate your system properly, and enjoy all of its advanced features. Save

your installation guide for future reference.

WARNING: To reduce the risk of fire or electric shock, do not expose the system to

rain or moisture.

WARNING: This apparatus shall not be exposed to dripping or splashing, and

objects filled with liquids, such as vases, shall not be placed on the apparatus. As

with any electronic products, use care not to spill liquids in any part of the system.

Liquids can cause a failure and/or a fire hazard.

CAUTION: No naked flame sources, such as lighted candles, should be placed on

the apparatus.

This product conforms to the EMC Directive 89/336/EEC and to the Low Voltage

Directive 73/23/EEC. The complete Declaration of Conformity can be found at

www.bose.com/static/compliance/index.html.

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connecting the VS-2 to Your Media Center . . . . . . . . . . . . . . . . . . . . . . . 6

Your TV Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using an HDMI TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using a Component Video TV Connection . . . . . . . . . . . . . . . . . . . . . . . 10

Using an S-Video TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using a Composite Video TV Connection . . . . . . . . . . . . . . . . . . . . . . . . 14

Program Recording Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operating Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Mounting Your VS-2 on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Maintaining Your VS-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SAFETY INFORMATION

Bose Corporation. No part of this work may be reproduced, modified, distributed, or otherwise

used without prior written permission. All trademarks referenced herein are property of Bose Corporation.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks

of HDMI Licensing LLC.

00_LasikOG.book Page 3 Thursday, October 26, 2006 1:23 PM

4

English

Introduction

About your LIFESTYLE

®

VS-2 video enhancer

The LIFESTYLE

®

VS-2 video enhancer allows you to connect more than one audio/video

device to your LIFESTYLE

®

home entertainment system. With this accessory installed, a

single button press selects the source video and audio at the same time.

Features and benefits

•Incorporates HDMI

TM

(High-Definition Multimedia Interface) technology to help maximize

your home theater experience.

• Provides HDMI, component, S-Video, and composite video connections for your TV,

cable/satellite box, VCR, or other A/V input devices.

• Converts lower-quality video input formats (composite or S-Video) up to higher quality

video output formats (component and HDMI).

• Compatible with HDTV and progressive scan TV formats.

How it fits into your LIFESTYLE

®

system

Video outputs from all your A/V devices, such as your cable/satellite box and VCR, connect

to the VS-2, but the audio outputs from these devices connect to the media center. The

VS-2 video output connects to your TV. When you select a source, such as your cable box

(CBL•SAT), the media center selects the cable box audio and directs the VS-2 to pass the

cable box video through to your TV.

Video

Audio

Video

Audio

AUX

CBL

•SAT

VCR

Video out

to TV

Video

TV

VS-2

LIFESTYLE

®

media center

IMPORTANT: Software update required!

Your VS-2 comes with a software update disc. After setting up the VS-2, you must

load this CD into the media center disc player and allow it to update your system.

Refer to “Updating the system software” on page 17.

00_LasikOG.book Page 4 Thursday, October 26, 2006 1:23 PM

5

English

Unpacking

Carefully unpack the VS-2 video enhancer. Check to be sure

your system includes the parts shown on this page. Save all

packing materials in case you need to repack and transport

your product.

If any part of the product appears damaged, do not attempt to

use it. Notify Bose or your authorized Bose

®

dealer immedi-

ately. For Bose contact information, refer to the address sheet

included in the carton.

WARNING: To avoid danger of suffocation, keep the

plastic bags out of the reach of children.

Finding a location for the VS-2

You can position the VS-2 on a shelf behind your media

center or behind your TV, or you can mount it on the back of

an entertainment center or on a wall. To mount it on a wall,

see

“Mounting Your VS-2 on a Wall” on page 20.

VS-2 video enhancer

VS-2 cable

For your records

Now is a good time to find the serial number on the bottom of the VS-2 video enhancer. Please record it here.

This provides easy access to this number if you ever need to contact Bose Customer Service.

Serial number: ________________________________ Purchase date: ________________________

Dealer name:__________________________________ Dealer phone: _________________________

Please keep your sales receipt with this owner’s guide.

If you need additional cables

Your VS-2 includes one HDMI-to-HDMI video cable, but you may need additional cables to set up the VS-2 with

your LIFESTYLE

®

system. To determine if you need any additional cables, please read this guide before you

begin the actual setup. You can purchase additional cables from your Bose dealer or local electronics retailer.

Software update disc

HDMI-to-HDMI cable

Owner’s

guide

Quick setup

guide

00_LasikOG.book Page 5 Thursday, October 26, 2006 1:23 PM

6

English

Connecting the VS-2 to Your Media Center

Preparation

When setting up a LIFESTYLE

®

system with the VS-2, the media center

power supply plugs into the VS-2 instead of the media center.

• If you are setting up the VS-2 and your LIFESTYLE

®

system at the

same time, find the media center power supply in the LIFESTYLE

system carton before you begin.

• If you are adding the VS-2 to an existing LIFESTYLE

®

system, turn

off your LIFESTYLE system, wait 30 seconds, and unplug the media

center power supply from the wall outlet. Then, disconnect the power

supply from the rear panel of the media center. Also, remove any video

cables from the Video OUT and Video IN connectors on the media center.

Connecting the VS-2 to your media center

VS-2 cable

VS-2 end panel

Media center power supply

Media center rear panel

WARNING: The VS-2 must be used only with the media center power supply

that came with your LIFESTYLE

®

DVD home entertainment system.

2

3

4

1

5

6

7

• Connect the 4-connector end of the VS-2 cable to your media center:

1 Insert the Serial Data plug into the Serial Data connector.

2 Insert the DC Power plug into the DC Power connector.

3 Insert the Composite plug into the Composite Video OUT connector.

4 Insert the S-Video plug into the S-Video OUT connector.

• Connect the other end of the VS-2 cable to the VS-2 end panel:

5 Insert multi-pin plug into the Media Center connector.

6 Insert the DC Power plug into the DC POWER Out connector.

• Connect the media center power supply to the end panel of the VS-2:

7 Insert the DC power cable from the media center power supply into the

DC POWER In connector.

Note: Straighten the DC power cord from the media center power supply and

from the VS-2 to the media center as much as possible. This cord is used as

the antenna for your LIFESTYLE

®

system remote control.

00_LasikOG.book Page 6 Thursday, October 26, 2006 1:23 PM

7

English

Your TV Connection Options

Identifying your TV connectors

Your TV may have some or all of the video input connectors

shown on the right. Each type of video connector provides

a different level of video image quality.

Examine the rear panel of your TV and determine whether it

has HDMI, component, S-Video, or composite video input

connectors. For additional instructions, refer to the owner’s

guide that came with your TV.

Choosing the TV connector you

will use

1. Using the table on the right, choose the available TV

video connector that provides the highest possible

video quality.

2. Make sure you have the correct cable on hand. An HDMI

cable is provided with the VS-2.

3. Go to the page listed for instructions on making the

connections to your TV and other A/V devices.

4. As a reminder, place a check mark in the table to indicate

your choice.

Composite

Standard quality

S-Video

Good quality

Component

Better quality

Video

Quality

TV Video

Connector Cable Type

Connection

Instructions

Check

One

Best HDMI

Go to page 8.

Better Component

Go to page 10.

Good S-Video

Go to page 12.

Standard Composite

Go to page 14.

Supplied with

the VS-2

Not supplied

Supplied

with your

LIFESTYLE

®

system

Supplied

with your

LIFESTYLE

®

system

HDMI

Best quality

DVI You may have a TV that has a DVI connector, but not an HDMI

connector. In this case, you still can use an HDMI connection by

using a DVI-to-HDMI cable adapter or a DVI-to-HDMI cable.

00_LasikOG.book Page 7 Thursday, October 26, 2006 1:23 PM

8

English

Using an HDMI TV Connection

Connecting the VS-2 HDMI output to your TV

To connect your TV to the VS-2 using the supplied HDMI cable, do the following:

1. Plug one end of the HDMI cable into the HDMI connector on the rear of your

TV.

2. Plug the other end of the HDMI cable into the Video OUTPUT HDMI connector

on the VS-2.

3. Go to page 9 for instructions on connecting other A/V devices to the VS-2.

TV

VS-2

00_LasikOG.book Page 8 Thursday, October 26, 2006 1:23 PM

9

English

Choosing connection types for your A/V devices

1. Look at the rear panel of each A/V device to determine what type of video output connectors it has.

2. In the following table, choose the type of available video connector that provides the highest possible video

quality. We recommend using an HDMI connection if it is available. Place a check mark in the table for the

connector type used for each of your A/V devices.

Connecting your A/V devices to the VS-2

1. Plug one end of the video cable into the appropriate video output connector(s) on your A/V device.

2. Plug the other end of the video cable into the appropriate Video INPUT connector(s) on the VS-2.

3. Refer to your LIFESTYLE

®

system installation guide for information on making audio connections.

Video

Quality

Video

Connector VCR CBL•SAT

AUX

(Other)

Best HDMI

Not

available

on VS-2

Better Component

Good S-Video

Standard Composite

VS-2

DO NOT USE

If any of your A/V devices do not have an HDMI connector, you can use any other

type of connection. Remember, the VS-2 converts these up to HDMI format.

00_LasikOG.book Page 9 Thursday, October 26, 2006 1:23 PM

10

English

Using a Component Video TV Connection

Connecting the VS-2 component video output to your

TV

You need to obtain a component video cable from Bose or your local electronics dealer to

complete this connection.

To connect your TV to the VS-2 using a component video cable (not supplied), do the

following:

1. Plug one end of the component video cable into the component connectors on the rear

of your TV. Be sure to match the color of each plug to the color of each connector.

2. Plug the other end of the component video cable into the Video OUTPUT Component

connectors on the VS-2. Again, be sure to match the color of each plug to the color of each

connector.

3. Go to page 11 for instructions on connecting other A/V devices to the VS-2.

TV

VS-2

00_LasikOG.book Page 10 Thursday, October 26, 2006 1:23 PM

11

English

Choosing connection types for your A/V devices

1. Look at the rear panel of each A/V device to determine what type of video output connectors it has.

2. In the following table, choose the type of available video connector that provides the highest possi-

ble video quality. We recommend using a component connection if it is available. Place a check mark in

the table for the connector type used for each of your A/V devices.

Connecting your A/V devices to the VS-2

1. Plug one end of the video cable into the appropriate video output connector(s) on your A/V device. If

you are making a component connection, be sure to match the color of the plug to the color of the

connector.

2. Plug the other end of the video cable into the appropriate Video INPUT connector(s) on the VS-2. Again,

if you are making a component connection, be sure to match the color of the plug to the color of the

connector.

3. Refer to your LIFESTYLE

®

system installation guide for information on making audio connections.

Video

Quality

Video

Connector VCR CBL•SAT

AUX

(Other)

Better Component

Good S-Video

Standard Composite

VS-2

If any of your A/V devices do not have component video connectors, you can use

either an S-Video or Composite connection. Remember, the VS-2 converts either

of these up to component video format.

00_LasikOG.book Page 11 Thursday, October 26, 2006 1:23 PM

12

English

Using an S-Video TV Connection

Connecting the VS-2 S-Video output to your

TV

You can use the S-Video cable included with your LIFESTYLE

®

system to

make this connection.

To connect your TV to the VS-2 using an S-Video cable, do the following:

1. Plug one end of the S-Video cable into the S-Video connector on the rear

of your TV.

2. Plug the other end of the S-Video cable into the Video OUTPUT S-Video

connector on the VS-2.

3. Go to page 13 for instructions on connecting other A/V devices to the VS-2.

TV

VS-2

00_LasikOG.book Page 12 Thursday, October 26, 2006 1:23 PM

13

English

Choosing connection types for your A/V devices

If you connected your TV to the VS-2 using an S-Video cable, you can use only an S-Video or Composite con-

nection for your A/V devices even though a device may have HDMI or component video output connectors.

1. Look at the rear panel of each A/V device to determine what type of video output connectors it has.

2. In the following table, choose the type of video connector that provides the highest possible video quality.

We recommend using an S-Video connection if it is available. Place a check mark in the table for the connec

-

tor type used for each of your A/V devices.

Connecting your A/V devices to the VS-2

1. Plug one end of the video cable into the appropriate video output connector on the rear of your A/V

device.

2. Plug the other end of the video cable into the appropriate Video INPUT connector(s) on the VS-2.

3. Refer to your LIFESTYLE

®

system installation guide for information on making audio connections.

Video

Quality

Video

Connector VCR CBL•SAT

AUX

(Other)

Good S-Video

Standard Composite

DO NOT USE

VS-2

If any of your A/V devices do not have an S-Video connector, you can use a

Composite connector. Remember, the VS-2 converts this up to S-Video format.

00_LasikOG.book Page 13 Thursday, October 26, 2006 1:23 PM

14

English

Using a Composite Video TV Connection

Connecting the VS-2 composite video output

to your TV

You can use the composite video cable included with your LIFESTYLE

®

system to

make this connection.

To connect your TV to the VS-2 using a composite video cable, do the following:

1. Plug one end of the composite video cable into the composite video

connector on the rear of your TV.

2. Plug the other end of the composite video cable into the Video OUTPUT

Composite connector on the VS-2.

3. Go to page 15 for instructions on connecting other A/V devices to the VS-2.

TV

VS-2

00_LasikOG.book Page 14 Thursday, October 26, 2006 1:23 PM

15

English

Choosing connection types for your A/V devices

If you connected your TV to the VS-2 using a composite video cable, you can use only an S-Video or Composite

connection for your A/V devices even though a device may have HDMI or component video output connectors.

1. Look at the rear panel of each A/V device to determine what type of video output connectors it has.

2. In the following table, choose the type of video connector that provides the highest possible video quality.

We recommend using an S-Video connection if it is available. Place a check mark in the table for the connec

-

tor type used for each of your A/V devices.

Connecting your A/V devices to the VS-2

1. Plug one end of the video cable into the appropriate video output connector on the rear of your A/V device.

2. Plug the other end of the video cable into the appropriate Video INPUT connector on the VS-2.

3. Refer to your LIFESTYLE

®

system installation guide for information on making audio connections.

Video

Quality

Video

Connector VCR CBL•SAT

AUX

(Other)

Good S-Video

Standard Composite

DO NOT USE

VS-2

00_LasikOG.book Page 15 Thursday, October 26, 2006 1:23 PM

16

English

Program Recording Connections

Connecting your cable/satellite box to

your VCR/DVR

To record programs from your cable or satellite service, you can connect

your cable/satellite box to your VCR or DVR. The diagram on this page

is an example of how this equipment may be connected.

Before you start, make sure that your cable/satellite box and VCR/DVR

have the necessary input and output connectors available.

Connect an unused video output on your cable/satellite box to an

unused video input on your VCR/DVR. Choose the connection

type that provides the highest level of image quality. Refer to

page 7.

Connect an unused audio output on your cable/satellite box to an

unused audio input on your VCR/DVR.

Recording programs

Using the connection method in the example diagram, you do not need

to select the CBL•SAT source in order to record the program. If you

wish, you can listen to another source while recording.

1

2

VCR/DVR video

to the VS-2

Cable/satellite video to the VS-2

VCR/DVR audio to

the media center

Cable/satellite audio

to the media center

VS-2

LIFESTYLE

®

media center

1

2

00_LasikOG.book Page 16 Thursday, October 26, 2006 1:23 PM

17

English

Operating Information

Updating the system software

1. Turn on your LIFESTYLE

®

system and select the CD/DVD source.

2. Load the software update disc into the media center disc player.

3. Wait for the display window of the media center to indicate when it is done.

New System menu items

When the VS-2 is connected to your LIFESTYLE

®

system, the following new items will appear in the System menu.

Video options

Audio options

New Item Possible Settings (Factory/default settings in bold type)

Widescreen TV No..................... Tells your LIFESTYLE

®

system that it is connected to a 4:3 TV.

Yes .................... Tells your LIFESTYLE

®

system that it is connected to a 16:9 (widescreen) TV.

Video Resolution

(only for HDMI TV

connection)

Adjustable ......Allows your LIFESTYLE

®

system to select the optimal video resolution setting for your TV.

Refer to Video Resolution in “New Settings menu items” on page 18.

Fixed.................Prohibits any change to video resolution.

Persistent Video Disabled .......... Removes video from your TV screen when switching from your selected video source to an

audio source.

Enabled............. Allows the video from your selected source (CBL•SAT, VCR, or AUX) to remain on your TV

screen when switching from this source to an audio source.

Settings on TV Yes ...................Allows the Settings menu for the TV, CBL•SAT, VCR, and AUX sources to appear on your TV

screen as well as on the media center display window.

No .....................Allows the Settings menu for the TV, CBL•SAT, VCR, and AUX sources to appear only on the

media center display window.

New Item Possible Settings (Factory/default settings in bold type)

CBL•SAT/VCR Audio

(only for HDMI

connections)

Bose 5.1 ..........Allows you to hear 5.1-channel surround sound from your LIFESTYLE

®

system when the

selected source is CBL•SAT or VCR. Recommended setting – should not be changed.

TV Stereo ..........Tells the VS-2 to send two-channel digital audio received (through an HDMI cable) from your

cable/satellite box or VCR to your TV (through an HDMI cable). The LIFESTYLE

®

system

speakers are silent.

IMPORTANT: Software update required!

Your VS-2 comes with a software update disc. To enable

the media center to operate with the VS-2, you must load

this CD into the media center disc player and allow it to

update your system.

00_LasikOG.book Page 17 Thursday, October 26, 2006 1:23 PM

18

English

New Settings menu items

When the VS-2 is connected to your LIFESTYLE

®

system, the following new items appear in the Settings menu.

New Menu Item Description Possible Settings (Factory/default settings in bold type)

Audio Delay Changes the amount of delay between

audio and video. Used to synchronize

the audio with the action when viewing

audio/video program content.

0 (no delay), 1, 2, 3, 4, 5, 6, 7, 8 (maximum delay)

Video Resolution Lists output video resolutions sup-

ported by your TV when it is connected

to the HDMI output of the VS-2. The

optimal resolution for your TV is listed

as the default setting and remains

selected unless you change it.

Available only when the Video Resolu-

tion option in the System menu is set

to Adjustable.

480/576p (lowest quality), 720p, 1080i, 1080p (highest quality)

Image View Modifies the image on your TV screen. Gray Bars ....Adds a vertical gray bar to the left and right side of the image.

Stretch ........Stretches the image horizontally to fit the screen.

Zoom ..........Image size is increased horizontally and vertically to fit the screen.

Normal .......Image is not changed.

SD Progressive

Scan

For standard-definition video,

determines whether interlaced or

progressive video is sent to your TV.

Available only when your TV is

connected to the VS-2 using a

component video cable.

Off ...............Sends interlaced video (480i or 576i) to your TV.

On ...............Sends progressive video (480p or 576p) to your TV.

00_LasikOG.book Page 18 Thursday, October 26, 2006 1:23 PM

19

English

Switching sources

Adding the VS-2 to your system setup greatly simplifies source selection. Just press the remote

button (CD/DVD, VCR, CBL•SAT, or AUX) for the source you want to use. If you select one of the

sources connected to the VS-2, be sure the source is turned on.

Selecting TV channels

When the VS-2 is connected to your LIFESTYLE

®

system, the remote changes channels on the

source selected by the TV Control setting (CBL•SAT, VCR, TV, or AUX) in the System menu under

Remote Control options. This means that when you select the TV source on the remote, you see

and hear the TV channel coming from your TV Control selection. For example, if you set TV

control to CBL•SAT and press the TV source button on your remote, you will see and hear the

program on the selected channel of your cable or satellite box.

If TV Control is set to TV (default setting), your TV screen goes blank when selecting the TV

source unless you enable the Persistent Video option (see

“New System menu items” on page 17).

If your TV screen is blank, the media center displays CHOOSE TV INPUT to remind you to select

the correct video input on your TV.

Watching video from one source while listening to audio from

another

Normally, when you switch to an audio source from a video source, your TV screen goes blank. To

change this so the video source remains on your TV screen, go to the System menu and change

the Persistent Video option setting to Enabled.

Enabling Persistent Video allows you to continue viewing the video portion of a program while

listening to the audio from another source, such as FM or AM radio. For example, you can watch a

ball game on your TV while listening to the broadcast audio of the same ball game from a local

radio station.

TV

CHOOSE TV INPUT

navigate

select

Choose the device that you have connected to the TV Audio IN jacks.

AUX Device:

AUX Brand:

AUX Code:

TV Control:

Remote Version

IR Control:

AUX

VCR

CBL•SAT

TV

Remote Control

Media center display – blank TV message

System menu – Remote Control options

00_LasikOG.book Page 19 Thursday, October 26, 2006 1:23 PM

20

English

Mounting Your VS-2 on a Wall

Required tools

Recommended hardware

Install two screws eight inches apart.

Leave ¼ inch (6 mm) between wall

surface and screw head.

Position the VS-2 mounting holes over the

screws so that it is flush with the wall.

Lower the VS-2 onto the screws

to lock it in place.

1

2

3

For solid wood

For wallboard

-inch (3.5 mm) drill bit

1

8

Use drill size

specified for type

of wall anchor

used.

No. 8 x 1½-inch

(M4 x 36 mm)

wood screws

No. 8 x 1½-inch (M4 x 36 mm)

wood or machine screws (depends

on type of wall anchor)

No. 8 (M4)

wall anchor

00_LasikOG.book Page 20 Thursday, October 26, 2006 1:23 PM

La pagina sta caricando ...

Bose AM301726 Manuale utente

Questo manuale è adatto anche per

Bose AM301726 Manuale utente

in altre lingue

Documenti correlati

Altri documenti