Simplicity MANUAL, OPS, ECLP21602KWV Manuale utente

Safety Instructions & Operator's Manual for

Manual No. 7104270 (Rev. ‘-’, 2/11/2010)

EUROPEAN

21” CAST ALUMINUM DECK

WALK MOWERS

COMMERCIAL MODELS

SERIES 2

Models

ECLP21602KWV (7800251)

!

Not for

Reproduction

Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your

confidence in the Snapper brand. When operated and maintained according to the instructions in this

manual, your Snapper product will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with the

machine and how to avoid them. This machine is designed and intended only for finish cutting of

established lawns and is not intended for any other purpose. It is important that you read and understand

these instructions thoroughly before attempting to start or operate this equipment. Save these original

instructions for future reference.

PRODUCT REGISTRATION

IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS

(Complete the following information on your Snapper purchase)

Date of Purchase__________________________________________________________________

Retailer_________________________________________________________________________

Retailer's Phone Number___________________________________________________________

Equipment

Model Number______________________________________________________________

Serial Number ______________________________________________________________

Engine

Model_________________________Type__________________Trim___________________

Briggs & Stratton Yard Power Products Group

SNAPPER is a trademark of

Briggs & Stratton Power Products Group, LLC

Jefferson, WI, USA.

Not for

Reproduction

3

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Decal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Starting & Stopping Engine & Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Propelling Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Handle Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Recycling Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installing the Grass Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Change Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Check Transmission Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Check Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Check Engine to Transmission Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Service - Periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Storage Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Blade Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Wheel Drive Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

WARNING

Battery posts, terminals and related accessories contain

lead and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

!

WARNING

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known to

the State of California to cause cancer or other reproductive

harm.

!

Not for

Reproduction

www.snapper.com4

!

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects

that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in

serious injury or death to the operator or other persons. The owner of the machine must understand these

instructions and must allow only persons who understand these instructions to operate machine. Each

person operating the machine must be of sound mind and body and must not be under the influence of any

substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your

machine which your dealer cannot answer to your satisfaction, call or write the Customer Service

Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

Protection for Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

and turn machine OFF if anyone enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

5. DO NOT pull mower backwards unless absolutely

necessary. LOOK and SEE behind and down for children,

pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Slope Operation

1. Slopes are a major factor related to slip and fall acci-

dents, which can result in severe injury. All slopes require

extra caution. If you feel uneasy on a slope, DO NOT mow

it.

2. Mow across slopes, never up-and-down. Exercise

extreme CAUTION when changing directions on slopes. DO

NOT mow steep slopes or other areas where stability or

traction is in doubt. Refer to the Slope Guide at the end of

this manual.

3. Use extra care with gcrass catchers or other attach-

ments; these affect the handling and the stability of the

machine.

Preparation

1. Read, understand, and follow instructions and warnings

in this manual and on the mower, engine and attachments.

Know the controls and the proper use of the mower before

starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others

from serious injury.

Preparation

(Continued From Previous Column)

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

Add fuel outdoors only with engine stopped and cool. Clean

spilled fuel and oil from machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Also note the location of holes, stumps, and other possible

hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop mower if

anyone enters the area.

7. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

8. Make sure all safety decals are clearly legible. Replace if

damaged.

9. Protect yourself when mowing and wear safety glasses, a

dust mask, long pants, and substantial footwear. DO NOT

mow barefooted or with sandals.

10. Know how to STOP blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the machine

into a trailer or truck.

12. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or torn

spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

Important Operator Safety Instructions

Not for

Reproduction

5

Important Operator Safety Instructions

Safe Handling of Gasoline

(Continued From Previous Page)

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the contain-

ers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehi-

cles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing

immediately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tighten

securely.

Operation

1. DO NOT put hands or feet near or under rotating parts.

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or

roads, and under any conditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of

alcohol or drugs.

5. After striking a foreign object or if mower vibrates

abnormally, STOP the engine, disconnect and secure spark

plug wire. Inspect the mower for any damage and repair the

damage before starting.

6. DO NOT mow near drop offs, ditches or embankments.

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your

footing. Keep a firm hold on the handle and walk, never run.

Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is

running.

10. DO NOT leave the machine with the engine running.

STOP BLADE and STOP ENGINE before leaving the opera-

tors position for any reason.

11. Before cleaning, repairing or inspecting make certain

engine, blade and all moving parts have STOPPED.

Disconnect and secure spark plug wire away from plug to

prevent accidental starting.

12. STOP engine and wait until the blade comes to com-

plete STOP before removing grass bag and/or clearing

grass.

Operation

(Continued From Previous Column)

13. DO NOT operate mower without the entire grass catch-

er, discharge guard, rear guard or other safety devices in

place and working. DO NOT point discharge at people,

passing cars, windows or doors.

14. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

Maintenance and Storage

1. DO NOT store mower or fuel container inside where

fumes may reach an open flame, spark or pilot light such as

in a water heater, furnace, clothes dryer or other gas appli-

ance. Allow engine to cool before storing machine in an

enclosure. Store fuel container out of reach of children in a

well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws

properly tight. Check that all cotter pins are in proper

position.

5. Always provide adequate ventilation when running

engine. Engine exhaust gases contain carbon monoxide, a

deadly poison.

6. Service engine and make adjustments only when engine

is stopped. Remove spark plug wire from spark plug and

secure wire away from spark plug to prevent accidental

starting.

7. DO NOT change engine governor speed settings or

overspeed engine.

8. Check grass bag assembly frequently for wear or

deterioration to avoid thrown objects and exposure to

moving parts. Replace with new bag if loose seams or tears

are evident. Replace slider or bag adapter if broken or

cracked.

9. Mower blades are sharp and can cut. Wrap the blades or

wear heavy leather gloves and use CAUTION when handling

them.

10. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

11. Have machine serviced by an authorized SNAPPER

dealer at least once a year and have the dealer install any

new safety devices.

12. Use only genuine SNAPPER replacement parts to

assure that original standards are maintained.

Not for

Reproduction

www.snapper.com6

(2) Warning Instructions:

A. Read, understand and follow instructions and warnings in the operator’s manual, as well as on the

mower, engine and attachments before operating.

B. Indicates possible severe injury from rotating cutting blades.

C. Do not operate without entire grass catcher or guard in place.

D. Keep children and others out of mowing area.

CA

DB

dB

Mfg. No. XXXXXXX

WALK BEHIND LAWN MOWER

S/N XXXXXXXXXX

SIMPLICITY MFG - SNAPPER

MCDONOUGH, GA 30253 USA

XX

2007

kg: XX

kW: X.XX

XXXX max

(1) Serial Tag:

A. Manufacturing (Part) Number

B. Description/Model Number

C. Serial Number

D. Manufacturer Information

E. Sound Power

F. Unit Mass

G. Kilowatts

H. Max RPM’s

I. Year of Manufacture

J. European Certification

E

A

F

D

B

C

G

H

J

I

Decal Identification

Not for

Reproduction

7

(3) Engine Speed Control:

Indicates direction to increase engine RPM (rabbit), decrease

engine RPM (turtle).

(4) Speed Selector:

Indicates ground speed selection: ‘3’ (Rabbit) indicates top

speed; ‘2’, medium speed; ‘1’ (Turtle), slowest speed.

Decal Identification

(5) Operator Presence Control (OPC):

Arrow points to the OPC bail. When bail is rotated rearward,

the engine may be started and will run as indicated by the

engine with rotating arrow. With the engine running, the

blade is rotating as indicated by the cut grass symbol. When

the bail is released and rotates forward, the engine will stop.

(6) Clutch:

Located on the plastic grip of the traction control lever.

Moving the lever toward the handle engages the traction

clutch and forward motion starts. When the lever is released,

the clutch disengages and forward motion stops.

(7) Height Control Instruction:

Shows direction of movement of Height Adjust Handle to

select a change in height of cut from highest cutting height

(clockwise) to the lowest (counterclockwise). Note that

there is a total of eleven heights of cut.

Not for

Reproduction

www.snapper.com8

IMPORTANT

The figures and illustrations in this manual are provided

for reference only and may differ from your specific

model. Contact your Snapper dealer if you have questions.

Features and Controls

A. Oil Fill Cap and Dipstick

B. Fuel Filler Cap

C. Mower Deck

D. Handle Bracket

E. Height-of-Cut Adjustment Handle

F. Discharge Door

G. Blade Control

H. Rope Start Handle

I. Ground Speed Control

J. Drive Wheel Control

K. Engine Speed Control

L. Grass Catcher

E

C

D

H

I

G

J

B

A

L

Features and Controls

K

F

Not for

Reproduction

9

Pre-Start Check List

Make the following checks and perform the service required

before each start-up.

1. Check the guards, deflectors, grass bag, adapter, and

covers to make sure all are in place and securely

tightened.

2. Check the blade control (A, Figure 1), wheel drive

control (B), and ground speed control (C) to insure they

work freely.

3. Check the cutting height. Adjust to the desired height.

Refer to the Section entitled ‘Cutting Height Adjustment’.

4. Check the engine oil (A, Figure 2) and add oil as needed

to bring the level up to the full mark. Refer to the Engine

Owner’s Manual for oil specifications.

5. Add fuel to the tank after pushing the mower outside

where fumes can safely dissipate. Fill the tank to 1-1/2

inches below the top of the filler neck (to allow for fuel

expansion). Make sure the cap (B, Figure 2) is tightened

after fueling. Refer to the Engine Owners Manual for fuel

specifications.

6. Clean the exterior surfaces of the cutting deck and

engine of any accumulation of spilled fuel, dirt, grass,

oil, etc. Keep the engine air intake screen and cooling

fins clear at all times.

Starting and Operation

Engine and Blade

1. Move the engine speed control (C, Figure 3) past the

fast (‘Rabbit’) detent to the ‘Choke’ position.

2. Make sure the fuel valve (A, Figure 3a) is set to the

open position.

3. Pull the blade control (A, Figure 3) against the handle.

4. Pull the rope start handle (B) to crank the engine.

5. After the engine starts, allow a brief warm-up until the

engine runs smooth, then turn off choke.

NOTE:

To stop the engine (and blade), release the blade

control.

Operation

Figure 2: Oil and fuel fill

B

C

A

Figure 1: Mower controls

B

Figure 3: Starting the mower

B

A

C

Figure 3a: Fuel valve

A

Not for

Reproduction

www.snapper.com10

Operation

Starting and Operation (Continued)

Propelling the Mower

1. Start the engine. Refer to the Section entitled “Starting

and Operation – Engine and Blade”.

2. Move the ground speed control (A, Figure 4) to the

desired speed position.

3. Squeeze the wheel drive control (B) against the handle

to engage the wheel drive and propel the mower

forward.

Important: Forward motion of the machine must be stopped

before changing the position of the ground speed control.

Stopping

1. Stop forward motion of the mower by releasing the

wheel drive control.

2. Stop the engine and blade by releasing the blade

control.

Handle Height Adjustment

The height of the mower handle can be adjusted as follows:

1. Loosen the lower nuts (A, Figure 5) on each

lower handle.

2. Move the handle assembly (B) up or down until the

desired position is achieved.

3. Tighten the lower nuts on each lower handle to maintain

the desired position.

Note: Torque the nuts to 15-25 ft-lbs.

Figure 5: Adjusting the handle height

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!

B

Figure 4: Mower drive controls

A

B

Not for

Reproduction

11

Operation

Cutting Height Adjustment

1. Pull the cutting height adjusting handle (A, Figure 6)

outward and move to the desired cutting height.

Recycling Operation

Converting this mower to the recycling operation requires no

tools. First, STOP the engine. Raise the discharge door (A,

Figure 7) located at the rear of machine. Remove the grass

catcher (if installed). Insert the recycling plug (B) fully into

the discharge opening. Allow the discharge door to close.

NOTE: For best recycling results, cut up to a maximum of

1/3 of grass blade length and recycle ONLY when grass is

dry.

1. Set the cutting height at the highest cutting position.

2. Move the engine speed control to the “FAST” (Rabbit)

position.

3. Move the ground speed control to the slowest speed

setting.

4. Proceed mowing slowly. If the grass is very dense, raise

the cutting height to improve recycling performance.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!

WARNING

Stop engine and mower blade by releasing the blade

control before adjusting cutting height.

!

Figure 7: Inserting the recycling plug

A

B

Figure 6: Adjusting cutting height

A

+

-

Not for

Reproduction

www.snapper.com12

Operation

Installing the Grass Catcher

1. Follow the WARNING statement found on this page.

2. Lift the discharge door (A, Figure 8) located at the rear

of the machine.

3. Install the grass catcher (B) onto the rear of the

machine. Position the rod ends (C) of the catcher frame

over the tabs (D) located at the rear of deck. Release the

discharge door, which is spring loaded, onto the top of

the grass catcher.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!

WARNING

DO NOT operate mower without entire grass catcher, side

chute or recycling plug in place. Grass Catcher

components are subject to deterioration during normal

use. Inspect frequently and replace worn or damaged

components immediately.

!

Figure 8: Installing the Grass Catcher

A

B

D

C

WARNING

Grass Catcher bags used on SNAPPER products are made

of woven fabric, and are subject to deterioration and wear

during normal usage. Check condition of bag before each

use. Immediately replace worn or damaged catcher bags

with only bags recommended by SNAPPER. The grass

catcher is optional equipment on some models.

!

Not for

Reproduction

13

Maintenance

Maintenance - Introduction

To retain the quality of the mower, use genuine SNAPPER

replacement parts only. Contact a local SNAPPER dealer for

parts and service assistance. For the correct part or

information for a particular mower, always mention the

model and serial number.

Service - After First 5 Hours

Change Engine Oil

NOTE: Due to the location of the oil drain plug, perform the

following procedure for the easiest oil change.

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tip the mower on its side, with the oil fill (A, Figure 9)

down. Do not tip the mower with the spark plug or car-

buretor down.

Important: Drain the fuel tank before tipping the machine.

DO NOT tip the machine with the carburetor or spark plug

down. Oil from the crankcase will saturate the air filter and

cause the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Place a shallow pan underneath the approximate center

of the oil fill.

4. Remove the oil fill cap and allow the oil to drain out

completely into the pan. Some oil may spill; immediately

wipe hands and engine clean with cloth rags. Dispose of

oil properly.

5. Tip the mower back up.

6. Fill the engine with oil as specified in the Engine Owner’s

Manual. Thereafter, change the oil after each 25 hours of

use.

Grease Level in Transmission

The transmission requires no lubrication or maintenance. If

transmission leaks or malfunctions, return machine to an

authorized Snapper dealer for repair.

Wheel Drive Control

The wheel drive control requires periodic adjustment to

maintain proper drive function. The adjustment is performed

with the thumbwheel located on the wheel drive control cable

and requires no tools. Refer to the section entitled “WHEEL

DRIVE CONTROL ADJUSTMENT”.

Figure 9: Draining the engine oil

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!

A

Not for

Reproduction

www.snapper.com14

Maintenance

Check Mower Blade

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels for access to the

blade cap screws (A, Figure 10). Do not tilt the mower

with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO

NOT tip the machine with the carburetor or spark plug down.

Oil from the crankcase will saturate the air filter and cause

the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Check the torque of the blade cap screws.

Recommended torque should be 40 ft. lbs.

4. Check the blade for sharpness, wear and damage. Refer

to the Section entitled “Blade Wear Limits”.

Check Engine to Transmission Drive Belt

1. Visually check the drive belt for cracking, fraying,

severed or exposed belt strands. If worn or damaged,

replace the belt before operating the mower. Contact a

local SNAPPER dealer for parts and service assistance.

Service - Periodic

Perform all maintenance as described in the “Service

Schedule” section of this manual.

Engine

Service the engine according to the engine owner’s manual.

Air Filter

Refer to the engine owner’s manual for service instructions.

Engine Oil

Refer to the engine owner’s manual for service instructions.

Storage Procedure

Refer to the Engine Owner’s Manual for directions regarding

engine storage preparations. Prepare the mower for “end of

season” storage as follows:

1. Drain the fuel from the fuel tank and let the engine run

until all fuel is out of the carburetor.

2. Disconnect and remove the spark plug wire away from

the spark plug before any other preparations are made!

3. Tape all openings closed to prevent spraying water into

the exhaust or air intakes during washing.

4. Tilt the mower up on its rear wheels and thoroughly

clean the underside of the deck. Do not tilt the mower

with the spark plug or carburetor down. Scrape away

any accumulation of grass with a putty knife and/or

wire brush.

5. Lubricate all exposed metal with a light coating of oil to

prevent corrosion.

6. Loosen the handle knobs. Carefully fold the handles

forward, “flexing” the control cables to prevent cable

damage.

7. Store the mower in a shed or other dry area, protected

from weather.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!

Figure 10: Tightening the blade cap screw

A

Not for

Reproduction

15

Maintenance

Mower Blade Replacement

Standard Blade Wear Limit

1. Inspect the blade (Figure 11) frequently for signs of

excessive wear or damage:

(A) New blade

(B) Wear limit (notch starts)

(C) Dangerous condition! Do not use on the mower!

Replace with a new blade.

Blade Sharpening

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels. Do not tilt the

mower with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO

NOT tip the machine with the carburetor or spark plug down.

Oil from the crankcase will saturate the air filter and cause

the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Remove the blade (B, Figure 12).

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!

Figure 11: Standard blade wear limits

A

B

C

WARNING

DO NOT use a cutting blade that shows signs of excessive

wear or damage. Refer to the Section entitled “MOWER

BLADE REPLACEMENT” for proper blade inspection and

service procedures.

!

Figure 12: Removing the mower blade

A

B

C

D

Not for

Reproduction

www.snapper.com16

Maintenance

Blade Sharpening (Continued)

4. Sharpen the blade on a grinding wheel at an angle of 22

to 28 degrees (B, Figure 13). DO NOT sharpen the blade

beyond the original cutting edge (A).

5. Check blade for balance. If necessary, correct balance by

grinding heavy end of blade.

6. Reinstall blade (B, Figure 12). Note the correct

assembly order:

(A) Blade hub

(B) Blade (flange facing down)

(C) Capscrews

(D) Nuts

7. Check torque of blade retaining cap screw.

Recommended torque should be 40 ft. lbs.

Wheel Drive Control Adjustment

(Engine To Transmission Drive Belt)

The wheel drive control requires periodic adjustment to

maintain proper engine to transmission drive belt tension.

The adjustment is located on the right handle and requires

no tools.

IMPORTANT: DO NOT operate the engine when inspecting or

adjusting the drive belt.

1. Visually check the engine drive belt for cracking, fraying,

severed or belt strands exposed. Replace the belt before

operating the mower.

2. Check for proper drive belt tension:

STOP the engine.

Shift the ground speed control to 1st and engage

the wheel drive control.

With the wheel drive control (A, Figure 14)

engaged, pull the mower handles, moving the

mower rearward.

Observe the rear wheels. If the rear wheels slide

on the surface (no rotation) the belt is properly

tensioned and the control does not require

adjustment.

3. If the rear wheels rotate, increase belt tension by

rotating the thumb screw (B) COUNTER-CLOCKWISE.

4. Turn the thumb screw one turn at a time and recheck

tension.

5. When proper belt tension has been set, operate the

machine and verify proper wheel drive control function.

IMPORTANT: DO NOT over-tighten the wheel drive control.

DO NOT operate if the control or drive does not function

properly. Contact your local SNAPPER Dealer for assistance.

IMPORTANT: If the machine creeps forward after the wheel

drive control is released, the cable is too tight and must be

readjusted to eliminate all forward movement. The machine

must not have any forward movement when the wheel drive

control is disengaged. If the wheel drive control fails to

return quickly to the “OFF” position when released, check for

a broken, binding, or kinked cable.

Figure 14: Wheel drive control adjustment

Do not sharpen

beyond original

cutting edge

22-28

0

Figure 13: Sharpening the mower blade

A

B

A

B

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!

Not for

Reproduction

17

Maintenance

ITEM SERVICE

PERFORMED

REF. EACH

USE

5

HRS

25

HRS

50

HRS

100

HRS

EACH

SEASON

Engine Oil Check Oil Level Page 9 X

Initial Oil Change Page 13 X

Periodic Oil Change Page 14 X*

Air Pre-Cleaner Clean Sponge Element Engine Manual X**

Air Cleaner Clean or Replace Engine Manual X**

Spark Plug Replace Engine Manual X

Engine Cooling

System

Clean Shroud and Fins Engine Manual X**

Drive Belt Check for Wear and

Tension

Page 14 X

Mower Blade Check for wear, Damage

& Replacement

Pages 12 - 16 X

Mower Deck Clean Debris

Accumulation

Page 9 X

Transmission

Grease

Check Grease Level Page 13 X X

* Change oil every 25 hours when operating under heavy load or high temperatures.

** Clean more often under dusty conditions or when air debris is present.

Service Schedule

Not for

Reproduction

Troubleshooting

www.snapper.com18

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

Engine Will Not Start Using

Recoil Starter

1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.

2. Engine needs choking. 2. Choke engine.

3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.

Engine Stalls or Stops After

Running

1. Blade control is released or is not being held

securely against handle.

1. Blade control should be held securely against handle

at all times during operation of mower.

2. Fuel tank empty. 2. Fill with fuel to proper level.

3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.

4. Spark plug defective or gap set improperly. 4. Service spark plug.

5. Water, debris or stale fuel in fuel system. 5. Drain and clean fuel system.

6. Choke on. 6. Turn off choke.

Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty. 1. Clean or replace filters.

2. Spark plug faulty. 2. Service spark plug.

3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.

4. Debris build-up on engine cooling screen. 4. Clean all debris from engine cooling system.

5. Choke on. 5. Turn off choke.

Excessive Vibration 1. Damaged, out of balance or bent mower blade. 1. Service mower blade.

2. Loose blade components. 2. Service and tighten loose parts.

3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.

4. Lumpy or frayed belt. 4. Contact authorized SNAPPER dealer.

Mower Will Not Move Loss Of

Traction

1. Damaged transmission 1. Contact authorized SNAPPER dealer.

2. Drive belt requires replacement or adjustment. 2. Contact authorized SNAPPER dealer.

3. Insufficient lubrication in transmission/differential. 3. Contact authorized SNAPPER dealer.

Cutting Grass Improperly 1. Cutting height too low or high. 1. Adjust cutting height.

2. Engine speed too slow. 2. Move engine speed control to ‘Fast’ position.

3. Forward ground speed too fast. 3. Move ground speed control to a slower speed.

4. Cutting blade dull or damaged. 4. Sharpen cutting edges or replace blade.

Poor Grass Discharge 1. Engine speed too fast. 1. Move engine speed control to ‘Fast’ position.

2. Forward speed too fast. 2. Move ground speed control to a slower speed.

3. Grass is wet. 3. Mow when grass is dry.

4. Excessively worn or damaged blade. 4. Service mower blade.

5. Build up of grass clippings and debris under deck. 5. Clean deck.

6. Improper blade installed on deck. 6. Install proper SNAPPER blade.

7. Blade installed improperly on deck. 7. Install blade properly.

Oil Leaking 1. Leaking engine case. 1. Contact authorized SNAPPER dealer.

2. Check and tighten drain plug.

3. Make sure dip stick or oil filler cap is securely in

place.

Not for

Reproduction

19

BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is

defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any

part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. Transportation

charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized

Service Dealer using our dealer locator at www.BriggsandStratton.com or www.Snapper.com.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular

purpose, are limited to one year from purchase or to the extent permitted by law. Liability for incidental or consequential

damages are excluded to the extent exclusion is permitted by law.

Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

or country to country.

WARRANTY PERIOD

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the

period of time stated above. “Consumer use” means personal residential household use by a retail consumer. “Commercial

use” means all other uses, including use for commercial, income producing or rental purposes. Once product has experienced

commercial use, it shall thereafter be considered as commercial use for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton products. Save your proof of purchase receipt. If you

do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will

be used to determine warranty eligibility.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Warranty service is available only through servicing

dealers authorized by Briggs & Stratton or BSPPG, LLC.

Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty

only covers defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper

maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in

a way not described in the Operator’s Manual or using the product after it has been damaged will void your warranty. Warranty is

not allowed if the serial number on the product has been removed or the product has been altered or modified in any way, or if the

product has evidence of abuse such as impact damage, or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the

Operator’s Manual, and serviced or repaired using genuine Briggs & Stratton parts. Damage caused by lack of maintenance or use

of non-original parts is not covered by warranty.

Normal Wear - Like all mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not

cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters,

belts, cutting blades, and brake pads (engine brake pads are covered) are not covered by warranty due to wear characteristics

alone, unless the cause is due to defects in material or workmanship.

Stale Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s

Manual. Damage caused by stale fuel (carburetor leaks, clogged fuel tubes, sticking valves, etc) is not covered by warranty.

* Applies to Briggs and Stratton engines only. Warranty coverage of non-Briggs and Stratton engines is provided by the engine manufacturer.

Item Consumer Use Commercial Use:

Equipment 2 Years 1 Year

Engine* 2 Years 1 Year

Battery 1 Year 1 Year

Not for

Reproduction

www.snapper.com20

Notes

Not for

Reproduction

La pagina sta caricando ...

Simplicity MANUAL, OPS, ECLP21602KWV Manuale utente

Questo manuale è adatto anche per

Simplicity MANUAL, OPS, ECLP21602KWV Manuale utente

in altre lingue

Documenti correlati

Altri documenti