Hoover DYC 9913AXX-S Manuale utente

INSTRUCTION BOOK

DYC 9913AX

Heat Pump Tumble Dryer

Norsk

Suomi

Porteguese

Deutsch

Français

Italiano

English

Dansk

Svenska

2

14

38

26

50

74

86

98

62

-

EN 2

Introduction

Delivery Information

Unpacking the Product

Safety Reminders

Use

Installation

The Laundry

Environmental Issues

Gias Service

Installation

Electrical Requirements

Adjusting the Feet

Ventilation

Preparing the Load

Clothes Preparation

Do Not Tumble Dry

Energy Saving

Sorting the Load

Controls and Indicators

Selecting the Programme

Door and Filter

Opening the Door

Filter

Filter Care Indicator

To Clean the Condenser Filter

Water Container

To Remove the Container

Operation

Delay Start Function

Cancelling and Resetting the Programme

Cleaning and Routine Maintenance

Cleaning the Dryer

Technical Specifications

Troubleshooting

Customer Service

Spares

Gias Service

Drain Hose Kit: Fitting Instructions

INDEX

3

4

5

6

7

8

9

10

11

12

13

INTRODUCTION

Use

Please check that the following items are

delivered with the appliance:

● Instruction manual

● Guarantee card

● Energy label

Remove the machine from

its packaging close to the

final location of the

machine.

1- Cut carefully around the

base of the packaging and

up one corner.

2- Remove the polythene

sleeve and lift the dryer off

the polystyrene base.

Please read and follow these instructions carefully and operate the machine accordingly. This

booklet provides important guidelines for safe use, installation, maintenance and some useful

advice for best results when using your machine.

Keep all documentation in a safe place for future reference or for any future owners.

Delivery Information

UNPACKING THE PRODUCT

Dispose of the packaging safely. Make

sure it is out of the reach of children,it is a

potential source of danger.

Failure to comply with the above can

compromise the safety of the appliance. You

may be charged for a service call if a problem

with your machine is caused by misuse.

Check that no damage has occurred to the

machine during transit. If it has, call for service

by GIAS.

EN 3

SAFETY REMINDERS

● This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities,or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

● Children should be supervised to ensure that they do not play with the appliance.

● WARNING Misuse of a tumble dryer may create a fire hazard.

●This machine is solely for domestic use, i.e. to dry household textiles and garments.

●This machine should only be used for its intended purpose as described in this manual. Ensure

that the instructions for installation and use are fully understood before operating the appliance.

● Do not touch the appliance when hands or feet are damp or wet.

● Do not lean on the door when loading the machine or use the door to lift or move the machine.

●Do not allow children to play with the machine or its controls.

● WARNING Do not use the product if the fluff filter is not in position or is damaged; fluff could be

ignited.

● WARNING Where the hot surface symbol is located the temperature rise during operation

of the tumble dryer may be in excess of 60 degrees C.

● Remove the plug from the electricity supply. Always remove the plug before cleaning the

appliance.

● Do not continue to use this machine if it appears to be faulty.

● Lint and fluff must not be allowed to collect on the floor around the outside of the machine.

● The drum inside may be very hot. Always allow the dryer to complete the cool down period before

removing the laundry.

SAFETY REMINDERS

EN 4

This appliance is marked according

t o th e E u r o p e a n d i r e c t i v e

2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly,

you will help prevent potential negative

consequences for the environment and human

health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product indicates that this

product may not be treated as household waste.

Instead it shall be handed over to the applicable

collection point for the recycling of electrical and

electronic equipment.

For more detailed information about treatment,

recovery and recycling of this product, please

contact your local city office,your household

waste disposal service or the shop where you

purchased the product. Disposal must be

carried out in accordance with local

environmental regulations for waste disposal.

European Directive 2002/96/EC

● To ensure the continued safe and efficient

operation of this appliance we recommend that

any servicing or repairs are only carried out by

an authorised GIAS service engineer.

GIAS Service

If the appliance is not running properly or

breaks down, switch it off and disconnect the

plug from the socket. Consult GIAS Service for

possible repair.

● All packaging materials used are

environmentally-friendly and recyclable.

Please help dispose of the packaging via

environmentally-friendly means. Your local

council will be able to give you details of current

means of disposal.

● To ensure safety when disposing of an old

tumble dryer disconnect the mains plug from

the socket, cut the mains power cable and

destroy this together with the plug. To prevent

children shutting themselves in the machine

break the door hinges or the door lock.

Environmental Issues

● Check that the product has no visible signs of

damage before use. If damaged do not use and

please call GIAS Service.

● Do not use adapters, multiple connectors

and/or extensions.

● Never install the dryer against curtains and be

sure to prevent items from falling or collecting

behind the dryer.

● The appliance must not be installed behind a

lockable door, a sliding door or a door with a

hinge on the opposite side to that of the tumble

dryer.

Installation

●Do not dry unwashed items in the tumble dryer.

● WARNING Do not tumble dry fabrics treated

with dry cleaning fluids.

●WARNING Foam rubber materials can, under

certain circumstances, when heated become

ignited by spontaneous combustion. Items

such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and

clothes or pillows fitted with foam rubber pads

MUST NOT be dried in the tumble dryer.

● Always refer to the laundry care labels for

directions on suitability for drying.

● Clothes should be spin dried or thoroughly

wrung before they are put into the tumble dryer.

Clothes that are dripping wet should not be put

into the dryer.

● Lighters and matches must not be left in

pockets and NEVER use flammable liquids

near the machine.

● Glass fibre curtains should NEVER be put in

this machine. Skin irritation may occur if other

garments are contaminated with the glass

fibres.

● Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes

and wax removers should be washed in hot

water with an extra amount of detergent before

being dried in the tumble dryer.

● Fabric softeners, or similar products, should

be used as specified by the fabric softener

instructions.

The Laundry

Air Outlets in the Base

EN 5

INSTALLATION

Tumble dryers are supplied to operate at a

voltage of 230V, 50 Hz single phase. Check that

the supply circuit is rated to at least 6A.

Electricity can be extremely dangerous.

This appliance must be earthed.

The socket outlet and the plug on the

appliance must be of the same type.

Do not use multiple adapters and/or

extension leads.

The plug should be accessible for

disconnection after the appliance has been

installed.

CE Appliance complies with European Directive

2004/108/EC, 2006/95/EC and subsequent

amendments.

Electrical Requirements

If the mains cord on this appliance is

damaged, it must be replaced by a special cord

which is ONLY obtainable from the spares

service. It must be installed by a competent

person.

You may be charged for a service call if a

problem with your machine is caused by

incorrect installation.

Once the machine is in

place the feet should

be adjusted to ensure

that the machine is

level.

Adjusting the Feet

Adequate ventilation must be provided in the

room where the tumble dryer is located to

prevent gases from appliances burning other

fuels, including open fires, being drawn into the

room during operation of the tumble dryer.

● Exhaust air must not be discharged into a

flue which is used for exhausting fumes from

appliances burning gas or other fuels.

● Check regularly that the air flowing through

the dryer is not restricted.

● Check the fluff filter after use, and clean, if

necessary.

●The inlet and outlets should be kept free from

obstructions. To ensure adequate ventilation

the space between the bottom of the machine

and the floor must not be obstructed. There

should be a gap of at least 12mm between the

machine and any obstructions.

● Prevent items from falling or collecting behind

the dryer as these may obstruct the air inlet and

outlet.

● NEVER install the dryer up against curtains.

VENTILATION

Do not plug the machine in and switch it

on at the mains until the installation is

completed.For your safety, this dryer must be

correctly installed. If there is any doubt about

installation, call GIAS Service for advice.

Important: During transport ensure that the

dryer is in an upright position, if it's necessary

you can only flip in the side shown;

Caution: If the product is in different side, wait

at least 4 hours before switching on so that the

oil can flow back into the compressor. Failure to

do this could result in damage to the

compressor.

EN 6

DRAIN HOSE : FITTING INSTRUCTIONS

WARNING! Switch off and remove the

tumble dryer plug from the electricity supply

before carrying out any work.

Fit the Hose as Follows:

1.Flip the machine

slowly to the right side.

2. The waste water

pipe is situated at the

right-hand side of the

machine (see the

picture). A grey hose

connects to the bridge

at the left hand side of

the machine. Using

pliers, remove the pipe

retaining clip from the

bridge.

4. Pull the hose off the

bridge connection.

5. Attach the black

hose from the kit,

(using the connector

a n d p i p e c l i p s

supplied), to the hose

removed from the

bridge connection.

7. Once the machine is

in place, check the

bottom to ensure that

the new hose does not

kink when pushing the

tumble dryer into

position.

8. Connect the new

drain hose to the waste

Water pipe.

9. Connect to the

m a i n s e l e c t r i c i t y

supply.

Caution: If the product

is in different side, wait

at least 4 hours before

switching on so that the

oil can flow back into

t h e c o m p r e s s o r.

Failure to do this could

result in damage to the

compressor.

To avoid emptying the water container after

each drying cycle, the water can be

discharged directly to a waste water drain pipe

(the same drainage system as household

sinks). Water Bye-Laws prohibit connection to

a surface water drain. The waste water drain

pipe should be located adjacent to the tumble

dryer.

The kit consists of:1 hose and 1 tap.

Do not install the product in a room where

there is a risk of frost occurring. At temperature

around freezing point the product may not be

able to operate properly: there is a risk of

damage if the water is allowed to freeze in the

hydraulic circuit (valves, hoses, pumps).

For a better product performance the ambient

room temperature must be between +2°C and

+35°C.

DRAIN HOSE KIT: FITTING INSTRUCTIONS

EN 7

PREPARING THE LOAD

Before using the tumble dryer for the first time:

● Please read this instruction book thoroughly.

● Remove all items packed inside drum.

● Wipe the inside of the drum and door with a

damp cloth to remove any dust which may

have settled in transit.

Make sure that the laundry you are going to dry

is suitable for drying in a tumble dryer, as shown

by the care symbols on each item.

Check that all fastenings are closed and that

pockets are empty. Turn the articles inside out.

Place clothes loosely in the drum to make sure

that they don't get tangled.

Clothes Preparation

● Cottons Max. 9 kg

● Synthetics Max. 4 kg

Maximum Drying Weight

Do not overload the drum, large items when

wet can exceed the maximum admissible clothes

load (for example: sleeping bags, duvets).

Sort the Load as Follows

. .

.

● By care symbols

These can be found on the collar or inside seam:

Suitable for tumble drying.

Tumble drying at high temperature.

Tumble drying at low temperature only.

Do not tumble dry.

If the item does not have a care label it must be

assumed that it is not suitable for tumble drying.

● By amount and thickness

Whenever the load is bigger than the dryer

capacity, separate clothes according to

thickness (e.g. towels from thin underwear).

● By type of fabric

Cottons/linen: Towels, cotton jersey, bed and

table linen.

Synthetics: Blouses, shirts, overalls, etc. made

of polyester or polyamid, as well as for

cotton/synthetic mixes.

● By drying level

Sort into: iron dry, cupboard dry, etc. For delicate

articles press the button to select low drying

temperature.

Woollens, silk, delicate fabrics, nylon stockings,

delicate embroidery, fabrics with metallic

decorations, garments with PVC or leather

trimmings, training shoes, bulky items such as

sleeping bags, etc.

Do Not Tumble Dry:

IMPORTANT: Do not dry articles which

have been treated with a dry cleaning fluid or

rubber clothes (danger of fire or explosion).

Only put into the tumble dryer laundry which

has been thoroughly wrung or spin-dried. The

drier the laundry the shorter the drying time thus

saving electricity.

ALWAYS

● Try to dry the maximum weight of laundry, this

will save time and electricity.

● Check that the filter is clean before every

drying cycle.

NEVER

● Exceed the maximum weight, this will waste

time and electricity.

● Put dripping wet items into the tumble dryer,

this may damage the appliance.

Energy Saving

During the last 15 minutes (roughly) the

load is always tumbled in cool air

EN 8

Programme Selector – Select the required programme.

Time Selection Button – Allows the user to change duration of the programme selected by

Programme Selector. It can be used only with the selection of: Mix&Dry, Shirts and Time

Programmes.

Delay Start Button – Allows the user to delay the start of the drying cycle (see details of

Operation ).

Acrylic and Synthetic Button – When pressed the default indicator will fade and will be

illuminated.

Anti- Crease Button – Allows the user to select a post drying anti-crease cycle.

Start/Pause Button – Press to commence/ to pause the selected drying programme.

Memo Button – Allows user to record the programme by pressing simultaneously the Anti-

Crease and the Acrylic Synthetic buttons for 3 seconds, after 2 minutes duration of the chosen

programme/option.

Filter Care indicator – Lights when the filter needs cleaning.

Empty Water indicator – Lights when the water container is full.

Program Display – Related indicator lights when a auto programme has been selected.

- Indicator will come on when the eco programme has been selected.

Refresh – The indicator lights up when the programme starts the cool down stage.

The Hoover Sensor Dry machine gives many options for drying the

laundry to suit all circumstances. The table on the next page lists

the programmes and the function of each programme.

Note:

The sensor may not detect a small load of small articles. For small

loads and separate items or pre-dried fabrics with low moisture

content, use the timed programmes.

If the sensor does not detect the item the dryer will only operate for

10 minutes before going into cooldown.

If the load is too large or too wet to tumble dry the dryer will

automatically go into cooldown after approximately 3 hours.

In these cases we advise to use a time cycles between 30 and

75minutes depending on the load size and dryness required, and

select high or low heat depending upon the fabric type.

CONTROLS AND INDICATORS

Control Panel and Indicator Lights

Time Selection

Button

Programme

Selector

Acrylic Synthetic

Button

Anti-Crease

Button

Filter Care

Indicator

Program

Display

SELECTING THE PROGRAMME

Start/Pause

Button

Delay Start

Button

Empty Water

Indicator

EN 9

SELECTING THE PROGRAMME

PROGRAMME

Bone Dry

Store Dry

Hang Dry

Iron Dry

Wool Finish

Rapid 40'

Mix & Dry

Shirts

Time

Memo

Relax

DESCRIPTION

Select the degree of dryness that you require. This range from

for bath towels and bathrobes, through for items that will be

put away without ironing, to the programme that leaves the laundry

suitable for ironing.

A gentle programme specially created to get woollens softer after

air-drying.This delicate warm air cycle, lasting 12 minutes, can

also be used to get woollens 'refreshed' after being stored in the

wardrobe.

This is a special program for a maximum load of 4kg. With this

program you can dry together cotton and synthetic fabrics.

This is a special program for shirts of max load of 3kg. For synthetic

shirts you have to press the Acrylic Synthetic button.

Time selection includes all the manual time programs: from 30

minutes to 180 minutes. The 20 minutes selection time in only cool

air ventilation (Refresh).

Memo Program allows to re-perform a program that the user has

saved before, without selecting the correct sequence of program

selector positions and option buttons for that particular program.

The programme provides a conditioning and anticrease function.

The dryer will heat the load for 9 minutes followed by a 3 minute cool

down period and is especially good for garments which may have

been left for some time prior to ironing, in a linen basket for

example. Garments may also become stiffened when dried outside

on a washing line or inside on radiators.

This programme relaxes the creases in the fabric making ironing

quicker and easier.

The Rapid 40' programme allows a drying cycle to be completed

quickly. This is an ideal programme for having dry, refreshed and

ready-to-wear clothes in less than 40'. This special programme

constantly monitors the temperature in the drum. The maximum load

is 2 kg and the programme is suitable for all types of fabrics where

tumble drying is appropriate.

DOOR and FILTER

EN 10

Opening the Door

Pull on handle to open

the door.

To restart the dryer,

close the door and

press .

WARNING! When the tumble dryer is in

use the drum and door may be VERY HOT.

Never stop a tumble dryer before the end of the

drying cycle unless all items are quickly

removed and spread out so that the heat is

dissipated.

Filter Care Indicator

Lights when the filter

needs cleaning.

Check and clean the

main filter in the door

and the condenser

filters allocated in the

bottom of the dryer,If

the laundry is not

drying check that the

filter is not clogged.

DO NOT USE WATER TO CLEAN THE FILTER.

Filter

IMPORTANT: To maintain the efficiency of the

dryer check that the fluff filter is clean before

each drying cycle.

Do not operate the dryer without the filters.

Clogged filters can increase the drying time

and cause damage which may result in

expensive repair costs.

1 . P u l l t h e f i l t e r

upwards.

2. Open filter as shown.

3.Gently remove lint

using a soft brush or

your fingertips.

4 . S n a p t h e f i l t e r

together and push

back into place.

To Clean the Condenser Filter

1 . R e m o v e t h e

kickplate.

2. Turn the two locking

levers anti-clockwise

and pull out the front

cover.

3. Gently remove the

filter frame and clean

any dust or fluff with a

cloth from the filter. Do

not use water to clean

the filter.

4. Remove the sponge

gently from its place

and then wash the

sponge by holding it

under a running tap

turning it so to remove

any dust or fluff.

5. Refit the front cover

ensuring it is in the

c o r r e c t w a y ( a s

indicated by the arrow)

and pushed firmly into

place. Lock the two

levers by turning them

clockwise.

6. Refit the kickplate.

WATER CONTAINER

EN 11

OPERATION

1. Open the door and load the drum with

laundry. Ensure that garments do not hinder

closure of the door.

2. Gently close the door pushing it slowly until

you hear the door 'click' shut.

3. Turn the Programme Selector dial to select

the required drying programme (see

Programme Guide).

4. If drying synthetics, acrylics or delicate items,

press the button to reduce the heat level.

The indicator will light up when the machine is in

low heat setting. To deselect in the first few

minutes of the programme, press the button

, after this time reset the machine to change the

setting.

5. Press the button. The dryer will start

automatically and the indicator above the

button will be continuously lit.

6. If the door is opened during the programme to

check the laundry, it is necessary to press to

recommence drying after the door has been

closed.

7. When the cycle is nearing completion the

machine will enter the cool down phase, the

clothes will be tumbled in cool air allowing the

load to cool down.

8. Following the completion of the cycle the

drum will rotate intermittently to minimize

creasing. This will continue until the machine is

switched OFF or the door is opened.

Do not open the door during the automatic

programs in order to obtain a proper drying.

1. Gently pull out the

w a t e r c o n t a i n e r

holding the handle.

When it is full the

water container will

weigh about 6 kg.

2. Tilt the water

container to empty the

water out through the

spout.

When empty, replace

the water container

back as shown; first

insert the base of the

container into position

as shown then gentle

push the top into

position.

3. Press Button to

restart the cycle.

NOTE: If you have the

option of drainage

near to the dryer you

can use the discharge

k i t t o p ro v i d e a

permanent drainage

for the water collected

in the container of the

dryer. This means that

you don't have to

em p t y t h e w a te r

container.

The water removed from the laundry during

the drying cycle is collected in a container

inside the door of the dryer. When the

container is full the indicator on the control

panel will light, and the container MUST be

emptied. However, we recommend that the

container is emptied after each drying cycle.

NOTE: Very little water will collect during the

first few cycles of a new machine as an internal

reservoir is filled first.

To Remove the Container

1

WARNING! If you open the door mid cycle,

before the cool-down cycle has completed,the

handle may be hot. Please use extreme caution

when attempting to empty the water reservoir

during the cycle.

IMPORTANT Always switch off and

remove the plug from the electricity supply

before cleaning this appliance.

For electrical data refer to the rating label

on the front of the dryer cabinet (with the door

open).

Technical Specifications

Cleaning the Dryer

Drum capacity 115 litres

Maximum load 9 kg

Height 85 cm

Width 60 cm

Depth 60 cm

Energy Label Band A -40%

OPERATION

● Clean the filter and empty the water

container after every drying cycle.

● Regularly clean the filters.

● After each period of use, wipe the inside of

the drum and leave the door open for a while to

allow circulation of air to dry it.

● Wipe the outside of the machine and the

door with a soft cloth.

● DO NOT use abrasive pads or cleaning

agents.

● To prevent the door sticking or the build up

of fluff clean the inner door and gasket with a

damp cloth after every drying cycle.

WARNING! The Drum, door and load may

be very hot.

CLEANING AND ROUTINE MAINTENANCE

Delay Start Function

The Delay Start Function allows the user to delay the start of the drying cycle by 1 to 24 hours.

When the function is first selected the display will show a delay of 1 hour, subsequent presses of

the button will increase the delay with 1 hour steps.

To commence the programme press and the appliance will complete the drying cycle at the

end of this time. The indicator light will flash to indicate that the start delay is in progress.

Cancelling and Resetting the Programme

To cancel a programme press the button for 3 seconds. In the TIME CONTROL display 0:00

Light will flash to indicate that it has been reset.

EN 12

Information for Test Laboratory

EN 61121 Programme

Programme To Use

-DRY COTTON

-HANG DRY

-IRON DRY

-HANG DRY + SYNTHETIC

-IRON DRY COTTON

-EASY-CARE TEXTILE

EN 13

TROUBLESHOOTING

What Might be the Cause of...

Defects you can remedy yourself

Before calling GIAS Service for technical

advice please run through the following

checklist. A charge will be made if the machine

is found to be working or has been installed

incorrectly or used incorrectly.

If the problem persists after completing the

recommended checks, please call GIAS

Service, they may be able to assist you over the

telephone.

Time display to end could change during

drying cycle. The time to end is

continuously checked during the drying

cycle and the time is adjusted to give the

best estimation time. The displayed time

may increase or decrease during the cycle

and this is normal.

Drying time is too long/clothes are not dry

enough…

● Have you selected the correct drying

time/programme?

● Were the clothes too wet? Were the clothes

thoroughly wrung or spindried?

● Does the filter need cleaning?

● Is the dryer overloaded?

● Has the option been selected from a

previous cycle?

The dryer does not operate…

● Is there a working electricity supply to the

dryer? Check using another appliance such as

a table lamp.

● Is the plug properly connected to the mains

supply?

● Is there a power failure?

● Has the fuse blown?

● Is the door fully closed?

● Is the dryer switched on, both at the mains

supply and at the machine?

● Has the drying time or the programme been

selected?

● Has the machine been switched on again after

opening the door?

CUSTOMER SERVICE

Spares

GIAS Service

Should there still be a problem with your dryer

after completing all the recommended checks,

please call GIAS Service for advice.

They may be able to assist you over the

telephone or arrange for a suitable appointment

for an engineer to call under the terms of your

guarantee. However, a charge may be made if

any of the following applies to your machine:

● Is found to be in working order.

● Has not been installed in accordance with the

installation instructions.

● Has been used incorrectly.

Always use genuine spares, available direct

from GIAS Service.

For service and repairs call your local GIAS

Service engineer.

The dryer is noisy…

● Switch off the dryer and contact GIAS Service

for advice.

The Indicator is on…

● Does the filter need cleaning?

The Indicator is on…

● Does the water container need emptying?

The manufacturer declines all responsibility

in the event of any printing mistakes in this

booklet. The manufacturer also reserves the

right to make appropriate modifications to

its products without changing the essential

characteristics.

Introduktion

Leveringsoplysninger

Udpakning af produktet

Sikkerhedspåmindelser

Installation

Anvendelse

Vasketøjet

Miljøhensyn

GIAS Service

Installation

Elektriske krav

Justering af fødder

Ventilation

Afløbsslangesæt: Monteringsvejledning

Forberedelse af ilægning af tøj

Klargøring af tøj

Sortering af vasketøj

Må ikke tørres i tørretumbler

Energibesparelse

Tørrevejledning

Knapper og indikatorer

Valg af program

Låge og filter

Åbning af lågen

Filter

Filterplejeindikator

Vandbeholder

Sådan aftages beholderen

Kondensator

Sådan udtages kondensatoren

Betjening

Forsinket start

Annullering og genindstilling af program

Rengøring og løbende vedligeholdelse

Rengøring af tørretumbleren

Tekniske specifikationer

Fejlfinding

Service

Reservedele

GIAS Service

INDEKS

15

16

17

18

19

20

21

22

23

24

25

DA 14

INTRODUKTION

Anvendelse

Kontrollér at følgende ting fulgte med

maskinen:

● Instruktionsbog

● Garantibevis

● Energietiket

Tag ma skinen ud af

emballagen, så tæt som

muligt på der, hvor den skal

stå.

1. Skær forsigtigt rundt om

den underste kant af

emballagen og op langs et

af hjørnerne.

2 . Ta g p o l y t h e n b e k -

lædningen af og løft

t ø r r e t u m b l e r e n a f

polystyrenfoden.

Læs venligst denne instruktionsbog grundigt igennem og følg anvisningerne. Denne

instruktionsbog giver dig nogle vigtige retningslinjer angående sikker anvendelse, installation,

vedligehold samt gode råd om hvordan, du opnår de bedste resultater med din maskine.

Opbevar alle papirer et sikkert sted, så du har dem når du skal bruge dem igen, eller hvis du sælger

maskinen.

Leveringsoplysninger

UDPAKNING AF PRODUKTET

Bortskaf emballagen på sikker vis.

Opbevares utilgængeligt for børn.

Følges ovenstående ikke kan maskinen

tage skade. Du kan komme til at betale for

reparation, hvis der opstår problemer med din

maskine, og dette skyldes misbrug.

Kontrollér at maskinen ikke er beskadiget,

når du modtager den. Hvis den er, skal du ringe

til GIAS.

SIKKERHEDSPÅMINDELSER

● Maskinen er ikke beregnet til at blive benyttet af personer (herunder også børn) med mindskede

fysiske, sensoriske eller mentale evner, eller af personer, der mangler erfaring og viden,

medmindre den person, der er ansvarlig for deres sikkerhed har observeret dem eller har

instrueret dem i, hvordan maskinen benyttes.

● Børn skal være under opsyn af en voksen for at sikre, at de ikke leger med maskinen.

● ADVARSEL Misbrug af tørretumbleren kan medføre brandfare.

● Maskinen er kun til husholdningsbrug, dvs. til at tørring af tekstilvarer og tøj I en husholdning.

● Denne maskine må kun anvendes til det tilsigtede formål som beskrevet I denne håndbog. Husk

at alle instruktioner vedr. installation og anvendelse skal både læses og forstås før maskinen tages

i brug.

● Undgå at røre ved maskinen med fugtige eller våde hænder og fødder.

● Man må ikke læne sig op af lågen, når der lægges tøj i maskinen, eller bruge lågen til at løfte eller

flytte maskinen.

● Børn må ikke lege med maskinen og dens knapper.

● ADVARSEL Produktet må ikke bruges hvis fnugfilteret sidder forkert eller er beskadiget; fnug

kan antændes.

● ADVARSEL Der hvor symbolet for varm overflade er placeret, kan temperaturen, under

tumbling, overstige 60 grader C.

● Tag stikket ud at kontakten. Tag altid stikket ud før apparatet rengøres.

● Maskinen må ikke anvendes, hvis den virker defekt.

● Bomuldsfibre og fnug må ikke ophobes på gulvet omkring maskinen.

● Tromlens inderside kan være meget varm. Lad altid tørretumbleren fuldføre afkølingsperioden

før tøjet tages ud.

DA 15

Denne maskine er markeret i

overensstemmelse med det

europæiske direktiv 2002/96/EC

vedrørende elektrisk affald og

elektronisk udstyr (WEEE).

Ved at sikre, at dette produkt bortskaffes

korrekt, bidrager du til at forhindre eventuelle

skadelige konsekvenser for miljøet og

helbredet, som ellers kan forårsages af

uhensigtsmæssig bortskaffelse af dette

produkt. Symbolet på produktet angiver, at

dette produkt ikke må bortskaffes som

husholdningsaffald. I stedet bør det overdrages

til en genbrugsstation med henblik på

genanvendelse af elektrisk og elektronisk

udstyr. Bortskaffelse bør ske i henhold til de

lokale miljømæssige regler. Du kan få

yderligere oplysninger om håndtering,

genskabelse og genanvendelse af dette

produkt ved at kontakte dit lokale rådhus,

genbrugsstationen eller den forhandler, du

købte produktet af.

Europæisk Direktiv 2002/96/EC

● For at sikre apparatets fortsatte sikre og

effektive drift anbefaler vi, at eventuel service

eller reparation kun udføres af en autoriseret

GIAS servicetekniker.

GIAS Service

Hvis maskinen ikke kører ordentligt eller går

istykker, så sluk for den og tag stikket ud af

stikkontakten. Kontakt GIAS Service mht.

eventuel reparation.

● Den anvendte emballage er miljøvenlig og

genanvendelig. Bortskaf emballagen med

tanke for miljøet. Hent vejledning til

bortskaffelse af emballagen hos din lokale

kommune.

● For at sikre sikker bortskaffelse af en gammel

tørretumbler, skal du tage stikket ud af væggen,

skære ledningen og stik af og smide dem ud.

Bræk hængslerne af lågen eller ødelæg låsen,

så det undgås at børn kommer til at lukke sig

selv inde i maskinen.

Miljøhensyn

● Kontroller at produktet ikke viser tegn på

beskadigelse – før det tages i brug. Er det

beskadiget må det ikke bruges og GIAS

Service skal kontaktes.

● Der må ikke anvendes adaptere, flere

stikdåser og/eller forlængerledninger.

● Tørretumbleren må aldrig installeres opad

gardiner, og genstande skal forhindres i at

falde ned bag ved eller samles bag

tørretumbleren.

● Maskinen må ikke installeres bag en dør, der

kan låses, bag en skydedør eller bag en dør,

hvor hængslet sidder i modsatte side af

tørretumblerens hængsel.

Installation

● Unlad at tørre uvaskede ting i tørretumbleren.

● ADVARSEL Man må ikke tø rretumble tø rt

stof behandlet med kemiske rensevæsker.

● ADVARSEL Skumgummimateriale kan,

under visse omstæ ndigheder, selvantæ nde,

hvis det bliver for varmt. Skumgummi (latex

skum), badehætter, vandafvisende tekstiler,

materialer med gummibehandlet bagside og

tøj eller puder medskumgummi fyld MÅ IKKE

tørres i tørretumbleren.

● Kontroller altid vaskemæ rkerne, om tø jet

tåler tørretumbling.

● Tø jet skal centrifugeres eller vrides

omhyggeligt, før det lægges I tørretumbleren.

Tøj, der er drivvådt, må IKKE lægges i

tørretumbleren.

● Lightere og tændstikker må ikke efterlades i

lommer, og der må ALDRIG anvendes

brandfarlige væsker i nærheden af maskinen.

● Glasfibergardiner må IKKE læ gges i

maskinen. Der kan opstå hudirritation, hvis

andre beklædningsgenstande kontamineres

med glasfibre.

● Tø j, der er blevet snavset af stoffer som

madolie, acetone, alkohol, benzin, petroleum,

pletfjerner, terpentin, voksprodukter og

voksfjerner, bør vaskes i varmt vand tilsat

ekstra meget vaskemiddel, før det tørres i

tørretumbleren.

● Skyllemidler eller lignede produkter skal

anvendes i overensstemmelse med

skyllemidlets brugervejledning.

Vasketøjet

SIKKERHEDSPÅMINDELSER

DA 16

INSTALLATION

Tørretumblere kan køre på 230V, 50 Hz

enfaset. Kontrollér at strømkredsen er

klassificeret til mindst 10A.

Elektricitet kan være meget farligt.

Dette apparat skal være jordforbundet.

Stikkontakten og maskinens stik skal

passe sammen.

Der må ikke anvendes flere adaptere

og/eller forlængerledninger.

Stikket skal være tilgængeligt til afbrydelse

efter,at apparatet er blevet installeret.

Dette apparat opfylder kravene i EU

direktiverne 2004/108/EC, 2006/95/EC og

efterfølgende ændringer.

Elektriske Krav

Hvis hovedledningen til denne maskine

erbeskadiget, skal den udskiftes med en

s æ r l i g l e d n i n g , s o m K U N f å s h o s

reservedelsforha ndleren. Den skal installeres

af en kvalificeret person.

Du kan komme til at betale for reparation,

hvis der opstår problemer med din maskine, der

skyldes ukorrekt installation.

Når maskinen er på

plads, skal fødderne

justeres, så maskinen

står vandret.

Justering af Fødder

Der skal være tilstrækkelig ventilation i det rum,

hvor tørretumbleren placeres, så det undgås at

gasser fra andre apparater, eller åben ild,

trækkes ind I rummet under tørrebumbling.

● Udsugningsluft må ikke afledes i en træ

kkanal, der er beregnet til aftræk af røggasser

fra apparater, der kører på gas eller anden

brændsel.

● Kontrollér regelmæ ssigt at luften, der strø

mmer gennem tørretumbleren, ikke hæmmes.

● Kontrollér fnugfiltret efter brug og rengør det

om nødvendigt.

● Indløb og udløb skal holdes fri for tilstopninger.

For at sikre tilstrækkelig ventilation må

mellemrummet mellem maskinens bund og

gulvet ikke tilstoppes. Der skal være mindst 12

mm fri luft mellem maskinen og ting, der kan

blokere.

● Genstande skal forhindres i at falde ned og

samles mellem tørretumblerens sider og

bagside, da disse kan tilstoppe luftindsugning

og -udsugning.

● Tø rretumbleren må ALDRIG installeres op

mod gardiner.

VENTILATION

Du må ikke sætte stikket i og tænde for

maskinen, før installationen er fuldført. Af

hensyn til din egen sikkerhed skal denne

tørretumbler være installeret korrekt. Hvis der er

nogen tvivl om installation, skal du ringe til GIAS

Service for rådgivning.

DA 17

Luftuttak i bunnen

Viktig:Sørg for at tørketrommelen er i oppreist

stilling under transport. Hvis det er nødvendig,

kan du snu den på siden som vist;

Forsiktig:Hvis produktet står på feil side, vent

minst 4 timer før du slår på maskinen slik at

o l j e n k a n s t r ø m m e t i l b a k e i n n i

kompressoren.

Unnlatelse av å gjøre dette kan

resultere i skader på kompressoren.

DA 18

AFLØBSSLANGE: MONTERINGSVEJLEDNING

ADVARSEL! Sluk for tørretumbleren, og

tag stikket ud af stikkontakten, før der udføres

noget arbejde.

Montér Slangen Som Følger:

1 . V i p f o r s i g t i g t

maskinen mod højre.

2. Spildevandsrøret er

anbragt i maskinens

højre side (se billedet).

En grå slange er

t i l s l u t t e t b r o e n i

maskinens venstre

side. Brug en tang til at

f j e r n e s l a n g e n s

holdeclips fra broen.

3. Træk slangen af

brotilslutningen.

4. Sæt den sorte

slange fra sættet til den

slange, der er taget af

brotilslutningen, ved

h j æ l p a f d e

medfølgende stik og

rørclips.

5. Anbring den hane,

der følger med sættet,

tæt på den resterende

slange.

6. Anbring den hane,

der følger med sættet,

tæt på den slange, der

sidder tilbage.

7.Når maskinen er klar,

skal det kontrolleres, at

den nye slange ikke

bukkes nedenunder,

når tørretumbleren

skubbes på plads.

8.Tilsl ut den nye

a f l ø b s s l a n g e t i l

spildevandsrøret..

9. Tilslut til lysnettet.

A d v a r s e l : H v i s

produktet har været

vendt til andre plien

kan nå at løbe tilbage i

kompressoren. Hvis

dette ikke overholdes,

Va nde t ka n tø m m e s d i rek t e ud i

spildevandsafløbet (samme afløbssystem

som vasken), så det ikke er nødvendigt at

tøm m e v andbeho l deren efte r h v er

tørrecyklus. I henhold til gældende forskrifter

for vand må afløbet ikke tilsluttes et afløb for

overfladevand. Spildevandsafløbet skal være

placeret ved siden af tørretumbleren.

Sættet består af 1 slange og 1 hane.

Dette produkt må kun anvendes i et frost

frit rum. Ved temperature under 2 gr. vil

produktet ikke fungere korrekt. Der er risiko for at

det hydrauliske system kan fryse. Produktet

fungerer optimalt fra 2-35 gr. Celsius.

FORBEREDELSE AF ILÆGNING AF TØJ

Før tørretumbleren anvendes første gang:

● Læs venligst denne instruktionsbog grundigt.

● Fjern alle genstande som er lagt ind I tromlen.

● Aftør tromlens inderside og låge med en fugtig

klud for at fjerne eventuelt støv, som har sat sig

under transporten.

Du skal sikre, at det vasketøj, du skal til at

tørre, egner sig til tørring i en tørretumbler,

som vist på vaskemærker på hver genstand.

Kontroller at alle lukninger er lukkede, og at

lommerne er tomme. Vend vrangen ud på

genstandene. Læg tøjet løst i tromlen for at

sikre, at det ikke filtrer sig sammen..

Klargøring Af Tøj

● Bomuld Maks. 9 kg

● Syntetiske stoffer Maks. 4 kg

Maksimal tørrevægt

Tromlen må ikke overfyldes, større, våde

ting, kan overstige den maksimalt tilladte vægt

(f.eks.: soveposer og dyner).

Sorter Tøjet, Der Skal Lægges I, Som Følger:

. .

.

● Efter vaskemærker

De findes i kraven eller på en indvendig søm:

Egnet til tørring i tumbler.

Tørring i tumbler ved høj temperatur.

Kun tørring i tumbler ved lav

temperatur.

Må ikke tørres i tørretumbler.

Hvis der ikke findes noget vaskemærke, må det

betragtes som uegnet til tørretumbling.

● Efter antal og tykkelse

Når det tøj, der skal lægges i, overstiger

tørretumblerens kapacitet, skal tøjet adskilles i

overensstemmelse med tykkelse (f.eks.

håndklæder fra tyndt undertøj).

● Efter stoftype

Bomuld/linned: Håndklæder, bomuldsjersey,

sengelinned og duge.

Syntetiske stof: Skjortebluser, skjorter, overalls,

osv., fremstillet af polyester eller polyamid samt

efter bomulds/syntetiske blandinger.

● Efter tørringsniveau

Sorter tøjet i: Strygetørt, Skabstørt, osv. For

sarte genstande tryk på knappen for at vælge

lav tørretemperatur.

Uld, silke, sarte stoffer, nylonstrømper, sart

broderi, stof med metaldekoration,

beklædningsgenstande med PVC eller

læderkanter, gummisko, pladskrævende

genstande, som f.eks. soveposer, osv.

Må ikke tørres I tørretumbler:

VIGTIGT: Tør ikke genstande som er

behandlet med kemisk rensevæske eller

gummitøj (fare for brand eller eksplosion).

I løbet af de sidste ca. 15 minutter tørres tøjet

altid i nedkølet luft.

Læg kun vasketøj i tørretumbleren som er

blevet grundigt vredet eller centrifugeret. Jo

mere tørt vasketøj er, jo kortere vil tørretiden

være og derved spare elektricitet.

ALTID

● Prøv altid at tørre vasketøj så meget vasketøj

som maskinen tillader, dette sparer både tid og

elektricitet.

● Det skal altid kontrolleres, at filtret er rent før

hver tørrecyklus.

ALDRIG

● Den maksimale vægt må aldrig overskrides,

dette vil spilde tid og elektricitet.

● Læg aldrig drivvåde genstande I

tørretumbleren, dette kan beskadige apparatet.

Energibesparelse

DA 19

KNAPPER OG INDIKATORER

Programvælger – Vælg det ønskede program.

Tidsindstillingsknap – Giver brugeren mulighed for at ændre varigheden af det valgte

program vha. programvælgeren. Den kan kun bruges ved valg af: Mix&Dry, Skjorter og

Tidsprogrammer.

Knap for udskudt start – Giver brugeren mulighed for at udskyde starten på tørrecyklussen

(se detaljer under Betjening).

Knap for akryl/syntetisk – Når der er trykket på standardindstillings-indikatoren, vil den

slukkes og vil lyse.

Antikrølknap – Giver brugeren mulighed for at vælge eftertørring med antikrølcyklus.

Start/Pause-knap – Tryk for at starte eller afbryde det valgte tørreprogram.

Memo-knap – Giver brugeren mulighed for at registrere det valgte program ved samtidig tryk på

knapperne for antikrøl og akryl/syntetisk i 3 sekunder, 2 minutter efter det valgte program/funktion

Indikator for filterbehandling – Tændes, når filtret skal rengøres.

Indikator for ingen vand – Tændes, når vandbeholderen er fyldt op.

Display for automatisk vaskeprogram – Den tilknyttede indikator tændes, når der er valgt et

automatisk vaskeprogram.

– Indikatoren vil lyse, når øko-programmet er valgt.

Opfriskning – Indikatoren tændes, når programmet starter nedkølingsfasen.

Kontrolpanel Og Indikatorlys

DA 20

Tidsindstillings

knap

Knap for

akryl/syntetisk

Antikrølknap

Filterpleje-

indikator

Displayet

Start/Pause

-knap

Forsinket

start-knap

Tøm vand

indikator

Programvælger

VALG AF PROGRAM

Denne Hoover sensor tørretumbler giver dig mange muligheder

for at tilpasse tørringen til dine specielle behov.

I tabellen nedenfor kan du se de forskellige programmer og

hvordan de fungerer.

Bemærk: Sensoren vil måske ikke kunne mærke hvis der kun er

få ting lagt I.Til små mængder tøj og enkelte stykker eller

fortørrede stoffer med lavt fugtindhold, skal de tidsindstillede

programmer anvendes. Indstil programmet til mellem 30 og 75

minutter afhængig af tøjmængden og den ønskede tørhedsgrad

og vælg høj eller lav varme afhængig af stoftype.

Hvis sensoren ikke kan mærke noget i tørretumbleren, kører den

kun i 10 min. før den går ind I afkølingsfasen.Er tøjmængden for

stor eller for våd til at tørretumbles, vil tørretumbleren automatisk

gå ind i afkølingsfasen efter ca. 3 timer.

La pagina sta caricando ...

Hoover DYC 9913AXX-S Manuale utente

Questo manuale è adatto anche per

Hoover DYC 9913AXX-S Manuale utente

Altri documenti