NEC MultiSync® LCD1550V Manuale del proprietario

MultiSync LCD1550V

User’s Manual

UÏivatelská pﬁíruãka

Bedienerhandbuch

δηγίες ρήσης

Manual del usuario

Manuel Utilisateur

Manuale utente

Gebruikershandleiding

Podr´cznik u˝ytkownika

Руководство пользователя

Kullan∂c∂ Klavuzu

00Cover_all.p65 9/8/01, 11:11 am1

00Cover_all.p65 9/8/01, 11:11 am2

Declaration

Declaration of the Manufacturer

We hereby certify that the colour monitor

MultiSync LCD1550V (LA-15R02)

is in compliance with

Council Directive 73/23/EEC:

– EN 60950

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

and marked with

NEC-Mitsubishi Electric Visual Systems, Corp.

MS Shibaura Bldg., 13-23,

Shibaura 4-chome,

Minato-Ku, Tokyo 108-0023, Japan

Power consumption of the monitor is less

than 3W when in power-saving mode.

00Cover_all.p65 9/8/01, 11:11 am3

TCO’99

This is a translation of the original English TCO'99 document.

MultiSync LCD1550V (LA-15R02)

Congratulations! You have just purchased a TCO’99

approved and labeled product! Your choice has

provided you with a product developed for

professional use. Your purchase has also contributed

to reducing the burden on the environment and also

to the further development of environmentally

adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established

method for encouraging the adaptation of goods and services to the

environment. The main problem, as far as computers and other

electronics equipment are concerned, is that environmentally harmful

substances are used both in the products and during the manufacturing.

Since it has not been possible for the majority of electronics equipment

to be recycled in a satisfactory way, most of these potentially damaging

substances sooner or later enter Nature.

There are also other characteristics of a computer, such as energy

consumption levels, that are important from the viewpoints of both the

work (Internal) and natural (external) environments. Since all methods of

conventional electricity generation have a negative effect on the

environment (acidic and climate-influencing emissions, radioactive

waste, etc.), it is vital to conserve energy. Electronics equipment in

offices consume an enormous amount of energy since they are often left

running continuously.

What does labelling involve?

This product meets the requirements for the TCO’99 scheme which

provides for international and environmental labelling of personal

computers. The labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional Employees), Svenska

Naturskyddsforeningen (The Swedish Society for Nature Conservation)

and Statens Energimyndighet (The Swedish National Energy

Administration).

00Cover_all.p65 9/8/01, 11:11 am4

The requirements cover a wide range of issues: environment,

ergonomics, usability, emission of electrical and magnetic fields, energy

consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence and

use of heavy metals, brominated and chlorinated flame retardants,

CFCs (freons) and chlorinated solvents, among other things. The

product must be prepared for recycling and the manufacturer is obliged

to have an environmental plan which must be adhered to in each

country where the company implements its operational policy. The

energy requirements include a demand that the computer and/or

display, after a certain period of inactivity, shall reduce its power

consumption to a lower level in one or more stages. The length of time

to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for

example, in respect of the reduction of electric and magnetic fields,

physical and visual ergonomics and good usability.

Environmental Requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires,

casings and housings. In turn, they delay the spread of fire. Up to thirty

percent of the plastic in a computer casing can consist of flame

retardant substances. Most flame retardants contain bromine or chloride

and these are related to another group of environmental toxins, PCBs,

which are suspected to give rise to severe health effects, including

reproductive damage in fisheating birds and mammals, due to the

bioaccumulative* processes. Flame retardants have been found in

human blood and researchers fear that disturbances in foetus

development may occur.

TCO’99 demand requires that plastic components weighing more than

25 grams must not contain flame retardants with organically bound

chlorine and bromine. Flame retardants are allowed in the printed circuit

boards since no substitutes are available.

Lead**

Lead can be found in picture tubes, display screens, solders and

capacitors. Lead damages the nervous system and in higher doses,

causes lead poisoning.

TCO’99 requirement permits the inclusion of lead since no replacement

has yet been developed.

00Cover_all.p65 9/8/01, 11:11 am5

Cadmium**

Cadmium is present in rechargeable batteries and in the

colourgenerating layers of certain computer displays. Cadmium

damages the nervous system and is toxic in high doses.

TCO’99 requirement states that batteries, the colourgenerating layers of

display screens and the electrical or electronics components must not

contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches, Mercury

damages the nervous system and is toxic in high doses.

TCO’99 requirement states that batteries may not contain any Mercury.

It also demands that no mercury is present in any of the electrical or

electronics components associated with the display unit.

CFCs (freons)

CFCs (freons) are sometimes used for washing printed circuit boards.

CFCs break down ozone and thereby damage the ozone layer in the

stratosphere, causing increased reception on Earth of ultraviolet light

with consequent increased risks of skin cancer (malignant melanoma).

The relevant TCO’99 requirement; Neither CFCs nor HCFCs may be

used during the manufacturing and assembly of the product or its

packaging.

* Bio-accumulative is defined as substances which accumulate within

living organisms.

** Lead, Cadmium and Mercury are heavy metals which are

Bioaccumulative.

To obtain complete information on the environmental criteria document,

order from:

TCO Development Unit

SE-114 94 Stockholm

SWEDEN

FAX Number: +46 8 782 92 07

E-mail (Internet): development@tco.se

You may also obtain current information on TCO’99 approved and

labelled products by visiting their website at:

http://www.tco-info.com/

00Cover_all.p65 9/8/01, 11:11 am6

English

âesky

Deutsch

Ελληνικά

Español

Français

Italiano

Nederlands

Polski

Русский

Türkçe

01b_XChapterOpener 9/8/01, 11:11 am1

01b_XChapterOpener 9/8/01, 11:11 am2

English-1

English

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN

EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS

CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE

COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have

sufficient magnitude to cause electric shock. Therefore, it is dangerous to make

any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation

and maintenance of this unit has been included. Therefore, it should be read

carefully in order to avoid any problems.

CAUTION

WARNING

RISK OF ELECTRIC SHOCK • DO NOT OPEN

Caution:

When operating the MultiSync LCD1550V (LA-15R02) with a 220-240V AC power

source in Europe, use the power cord provided with the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse

installed for use with this equipment. If a power cord is not supplied with this equipment

please contact your supplier.

When operating the MultiSync LCD1550V with a 220-240V AC power source in

Australia, use the power cord provided with the monitor.

For all other cases, use a power cord that matches the AC voltage of the power outlet

and has been approved by and complies with the safety standard of your particular

country.

ENERGYSTAR is a U.S. trademark.

As an ENERGYSTAR

®

Partner, NEC-Mitsubishi Electronics Display of America, Inc. has

determined that this product meets the ENERGYSTAR guidelines for energy efficiency.

The ENERGYSTAR emblem does not represent EPA endorsement of any product or service.

IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of

International Business Machines Corporation.

Apple and Macintosh are registered trademarks of Apple Computer Inc.

Microsoft and Windows are registered trademarks of the Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

All other trademarks or registered trademarks are property of their respective owners.

01b_English 9/8/01, 11:11 am1

English-2

Contents

Your new NEC MultiSync LCD monitor box* should contain the following:

• MultiSync LCD1550V

monitor with tilt base

• Power Cord(s)

• Video Signal Cable

• User’s Manual

• CD ROM (includes complete User’s Manual in PDF format). To see

the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.

* Remember to save your original box and packing material to transport

or ship the monitor.

1

5

0

V

01b_English 9/8/01, 11:11 am2

English-3

English

Quick Start

To attach the MultiSync LCD monitor to your system, follow these

instructions:

1. Turn off the power to your computer.

2. Remove connector cover and cable cover.

3. For PC: Connect the 15-pin mini D-SUB of the appropriate

signal cable to the connector for the display card in your system

(Figure A.1). Tighten all screws.

For Mac: Connect the MultiSync LCD1550V Macintosh cable

adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB

end of the appropriate signal cable to the MultiSync LCD1550V

Macintosh cable adapter (Figure B.1). Tighten all screws.

4. Connect the 15-pin mini D-SUB of the video signal cable to the

appropriate connector on the back of the monitor (Figure C.1). Place

the Video Signal Cable under Clip B.

5. Connect one end of the power cord to the MultiSync LCD Series

monitor and the other end to the power outlet. Place the video signal

cable and AC power cord under the clips (Figure C.1). Replace

connector cover and cable cover.

NOTE: Adjust the position of the cable under the clips to avoid damage

for cable or monitor.

NOTE: Please refer to Caution section of this manual for proper

selection of AC power cord.

6. The Vacation Switch on the right side of the monitor must be turned

on (Figure D.1). Turn on the monitor with the Power Button and the

computer.

NOTE: The Vacation Switch is a true on/off switch. If this switch is on

the OFF position, the monitor cannot be turned on using the

front button DO NOT switch on/off repeatedly.

7. No-touch auto adjust automatically adjusts the monitor to optimal

settings upon initial setup for most timings. For further adjustments,

use the following OSM controls:

• Auto Adjust Contrast

• Auto Adjust

01b_English 9/8/01, 11:11 am3

English-4

Refer to the Controls section of this User’s Manual for a full description

of these OSM controls.

NOTE: If you have any problems, please refer to the Troubleshooting

section of this User’s Manual.

Figure B.1

Macintosh

Cable

Adapter

(not included)

Macintosh G3

and G4 do not

need a

Macintosh cable

adapter

Figure A.1

01b_English 9/8/01, 11:11 am4

English-5

English

Tilt

Grasp both sides of the monitor screen with your hands and adjust the

tilt as desired (Figure TS.1).

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Remove the connector cover and cable cover (Figure R.1).

2. Disconnect all cables.

3. Place monitor face down on a non-abrasive surface (Figure R.2).

Vacation Switch

Power Button

Figure C.1

1

5

0

V

Figure D.1

Connector cover

Cable cover

Clip B

01b_English 9/8/01, 11:11 am5

English-6

Figure TS.1

Figure R.1

4. Remove the 4 screws connecting the monitor to the stand and lift off

the stand assembly (Figure R.2) the monitor is now ready for

mounting in an alternate manner.

5. Connect the AC cord and signal cable to the back of the monitor

(Figure R.3).

6. Reverse this process to reattach stand.

NOTE: Use only VESA-compatible alternative mounting method.

01b_English 9/8/01, 11:11 am6

English-7

English

7. This LCD monitor is designed for use with a flexible arm. Please use

the attached screws (4pcs) when mounting. To meet the safety

requirements the monitor must be mounted to an arm which

guaranties the necessary stability under consideration of the weight

of the monitor. The LCD monitor shall only be used with an approved

arm (e.g. GS mark).

Figure R.2

Figure R.3

Non-abrasive

surface

01b_English 9/8/01, 11:11 am7

English-8

4 SCREWS (M4)

(MAX depth: 8.5 mm)

If use other

screw, check

depth of hole.

Weight of LCD assembly: 3.2kg (MAX)

Replace screws

Tighten all screws

75 mm

Thickness of bracket (arm)

2.0 ~ 3.2 mm

01b_English 9/8/01, 11:11 am8

English-9

English

Brightness/Contrast Controls

BRIGHTNESS

Adjusts the overall image and background screen

brightness.

CONTRAST

Adjusts the image brightness in relation to the

background.

AUTO ADJUST

Adjusts the image displayed for non-standard

video inputs.

Menu

Exits the OSM controls.

Exits to the OSM main menu.

Moves the highlighted area left/right to select control

menus.

Moves the highlighted area up/down to select one of the

controls.

Moves the bar left/right to increase or decrease the

adjustment.

Activates Auto Adjust function.

Enter the sub menu.

Moves the highlighted area of main menu right to select

one of the controls.

Resets the highlighted control to the factory setting.

Controls

OSM (On-Screen-Manager) Controls

The OSM controls on the front of the monitor function as follows:

To access OSM press any of the control buttons ( , , -, +, NEXT).

NOTE: When RESET is pressed in the main and sub-menu, a warning

window will appear allowing you to cancel the RESET function

by pressing the EXIT button.

Control

EXIT

CONTROL /

ADJUST -/+

01b_English 9/8/01, 11:11 am9

English-10

Auto Adjust

Automatically adjusts the Image Position, the H. Size

and Fine setting.

Position Controls

LEFT/RIGHT

Controls Horizontal Image Position within the display

area of the LCD.

DOWN/UP

Controls Vertical Image Position within the display area

of the LCD.

H. SIZE

Adjusts the horizontal size by increasing or decreasing

this setting.

FINE

Improves focus, clarity and image stability by increasing

or decreasing this setting.

Colour Control Systems

Five colour presets select the desired colour setting.

Each colour setting is adjusted at the factory.

R,G,B

Increases or decreases Red, Green or Blue colour

depending upon which is selected. The change in colour

will appear on screen and the direction (increase or

decrease) will be shown by the bars.

Tools

OSM POSITION

You can choose where you would like the OSM control

image to appear on your screen. Selecting OSM

Location allows you to manually adjust the position of

the OSM control menu left, right, down or up.

01b_English 9/8/01, 11:11 am10

English-11

English

OSM TURN OFF

The OSM control menu will stay on as long as it is use.

In the OSM Turn Off submenu, you can select how long

the monitor waits after the last touch of a button to shut

off the OSM control menu. The preset choices are 10,

20, 30, 45, 60 and 120 seconds.

OSM LOCK OUT

This control completely locks out access to all OSM

control functions. When attempting to activate OSM

controls while in the Lock Out mode, a screen will

appear indicating the OSM controls are locked out.

To activate the OSM Lock Out function, press , then

and hold down simultaneously. To de-activate the OSM

Lock Out, press , then and hold down

simultaneously.

RESOLUTION NOTIFIER

This optimal resolution is 1024 x 768. If ON is selected,

a message will appear on the screen after 30 seconds,

notifying you that the resolution is not at 1024 x 768.

FACTORY PRESET

Selecting Factory Preset allows you to reset all OSM

control settings back to the factory settings. The RESET

button will need to be held down for several seconds to

take effect. Individual settings can be reset by

highlighting the control to be reset and pressing the

RESET button.

Information

DISPLAY MODE

Indicates the current display resolution and frequency

setting of the monitor.

MONITOR INFO.

Indicates the model and serial numbers of your monitor.

01b_English 9/8/01, 11:11 am11

English-12

OSM Warning

OSM Warning menus disappear with Exit button.

NO SIGNAL: This function gives a warning when there

is no signal present. After power is turned on or when

there is a change of input signal or video is inactive, the

No Signal window will appear.

RESOLUTION NOTIFIER: This function gives a

warning of use with optimized resolution. After power is

turned on or when there is a change of input signal or

the video signal doesn’t have proper resolution, the

Resolution Notifier window will open. This function can

be disabled in the TOOL menu.

OUT OF RANGE: This function gives a

recommendation of the optimized resolution and refresh

rate. After the power is turned on or there is a change of

input signal or the video signal doesn’t have proper

timing, the Out Of Range menu will appear.

CHECK CABLE: This function will advise you to check

all Video Inputs on the monitor and computer to make

sure they are properly connected.

01b_English 9/8/01, 11:11 am12

La pagina sta caricando ...

NEC MultiSync® LCD1550V Manuale del proprietario

Questo manuale è adatto anche per

NEC MultiSync® LCD1550V Manuale del proprietario

in altre lingue

Documenti correlati