Stratco Handi-Pod™ HP2 Guida d'installazione

Tipo
Guida d'installazione
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
HANDI-POD® GARDEN SHED
HP2
BEFORE YOU START
• It is important that you contact your local government authority to determine if building approval is required.
Handi-Pod® Garden Sheds must be securely bolted to a permanent concrete base with sucient masonry anchors securing all
mounting locations as indicated in Figure 5.1 to prevent wind uplift. The installer is responsible for ensuring the slab or concrete
pads are sucient to support the shed and sustain wind loading. Do not directly anchor your shed to pavers. Two options for
concrete bases are listed below:
Base Option 1 - Before building the shed pour a concrete base that is larger than the area of the shed by at least 200mm in
each direction. The base should be poured so the concrete outside the shed floor area slopes away from the shed to help
prevent water entering the shed.
Base Option 2 - Substantial concrete pads may be used at each anchor location as an alternative to a complete concrete
floor. It is recommended pads are minimum Ø250mm x 400mm deep and embedded into a firm natural soil base.
Handi-Pod® Garden Sheds are suitable for wind classifications N1,N2 & N3. Handi-Pod® Garden Sheds are not suitable for N4 or
Cyclonic wind classifications. Check with Stratco sta for the wind classification of the location the Handi-Pod® Garden Shed
will be erected.
Care must be taken when determining the location of the Handi-Pod
®
Garden Shed as to not place the shed in close
contact with sources of pollution or environmental factors that could aect the life of the steel.
• It is essential to clear and level the site prior to assembling your Handi-Pod® Garden Shed.
There are dierent types and colours of screws used. Ensure the correct type and colour screw is being used at each location.
• Do not traverse the roof of the Handi-Pod® Garden Shed.
• Use heavy gloves and safety glasses when handling steel and never attempt to install a shed in windy conditions.
Where necessary, components are marked with a coloured sticker as to easily dierentiate one from another. Components are
referenced throughout the installation guide by their colour. For example, Panel (Short) is marked with a red sticker.
Rivet Gun
• Caulking Gun & Silicone
• Cordless Drill
• Hammer Drill (if Cordless Drill has no Hammer function)
• 5/16 Hex-head & PH2 Phillips-head Bit (Supplied in Kit)
• 10mm Masonry Drill Bit
• 3.5mm Drill Bit (Supplied in Kit)
• Ladder, Tape Measure
TOOLS AND HARDWARE REQUIRED
Right
Left
Right
Left
Long
Short
Right
Left
Right
Left
Long
Short
Downpipe Strap
Right
Left
Right
Left
Long
Short
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
Door StopDoor & Door Jamb
Panel (Short) Barge Panel:
Left
Right
Downpipe OutletDoor Handle Tongue Anchor Plate
Wafer-Head Self-
Drilling Screw -
22mm - Plain
Roof Flashing
(Lower)
Gutter
COMPONENTS
Wafer-Head
Self-Drilling
Screw - Plain
Roof Flashing
(Upper)
M8 Masonry
Anchor
Hex-Head Self-
Drilling Screw +
Washer - Colour
Hex-Head Self-
Drilling Screw
- Colour
Rivet
Roof Sheets Downpipe Wall Brace Bottom Channel
Door Handle
Wafer-Head
Self-Drilling
Screw - White
Sheetmetal
Screw- White
Sheetmetal
Screw- Colour
Panel (Long)
13
3
6
4
1
2
13
12
11
10
16
9
9
7
8
5
9
13
14
15
16
COMPONENT DIAGRAM
1. DOWNPIPE
2. DOWNPIPE OUTLET
3. GUTTER
4. ROOF SHEET
5. ROOF FLASHING (UPPER)
6. ROOF FLASHING (LOWER)
7. BARGE PANEL - LEFT
8. BARGE PANEL - RIGHT
9. WALL BRACE
10. DOOR JAMB
11. DOOR
12. DOOR STOP
13. BOTTOM CHANNEL (LONG)
14. WALL PANEL (SHORT)
15. WALL PANEL (LONG)
16. ANCHOR PLATE
Bottom Channel
Bottom Channel
Wafer-Head Self-
Drilling Screw
- Plain
Note: Channel end with tab
and large holes on outside
Wafer-Head
Self-Drilling
Screw - Plain
Anchor Plate
Bottom Channel
1
2
3
5
6
7
4
8
Bottom Channel
Wafer-Head Self-Drilling
Screw - White
Panel (Short)
Panel (Short)
Door Opening
Bottom
Channel
Panel
Panel (Long)
Bottom Channel
Door Opening
Bottom Channel (Long)
Wafer-Head Self-Drilling
Screw - White
Panel (Short)
Panel (Short)
Door Opening
Bottom
Channel
Panel
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
FIGURE 1.0
BASE ASSEMBLY
Lay out the Bottom Channels (Figure 1.0). Fasten the Bottom
Channels together at corners with two Plain Wafer-Head
Self-Drilling Screws in each corner.
FIGURE 1.1
Fasten two Plain Wafer-head Self-Drilling Screws through
the Bottom Channels and into each Anchor Plate. There are
eight Anchor Plates in total.
FIGURE 1.3
Fit a Panel (Short) to the front Bottom Channel.
Fit a Panel (Long) to the left side Bottom Channel. Install the
Panel (Long) at an angle (Figure 1.4).
FIGURE 1.4
Fasten the Panel (Short) to the Bottom Channel with four
white Wafer-Head Self-Drilling Screws.
FIGURE 1.2
Wafer-Head Self-Drilling
Screw - White
Sheetmetal Screw - White
Panel
Panel (Long)
Wafer-Head Self-Drilling
Screw - White
Panel (Long)
Wafer-Head Self-Drilling
Screw - White
Panel (Long)
Door Opening
Door Opening
Panel (Long)
Bottom Channel
FIGURE 1.6
Fasten the Panel (Long) to the Bottom Channel with eight
white Wafer-Head Self-Drilling Screws.
Ensure Panels lap together at corners in the correct manner.
The Left Panel fits into the inside of the Front Panel. The
Rear Panel fits into the inside of the Side Panels.
FIGURE 1.5
Front Panel
Left Panel Right Panel
Rear Panel
Panels lap together at corners
Door Opening
FIGURE 1.8
Fasten the Panel (Long) to the Bottom Channel with six
white Wafer-Head Self-Drilling Screws.
FIGURE 1.9
Fit a Panel (Long) to the rear Bottom Channel. Install the
Panel (Long) at an angle (Figure 1.9).
FIGURE 1.7
Fit a Panel (Long) to the right side Bottom Channel. Install
the panel at an angle (Figure 1.7).
Sheetmetal Screw - White
Panel
Screw Here
Sheetmetal Screw - White
Continued Figure 1.12
Door Stop
Panel (Short)
Bottom Channel
Door Stop tab
Bottom
Channel slot
Sheetmetal Screw - White
Panel
Screw Here
Sheetmetal Screw - White
Continued Figure 1.12
Fasten one white Sheetmetal Screw through the top corner
of each Panel overlap.
FIGURE 1.11
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
Wafer-Head Self-Drilling
Screw - White
Wafer-Head Self-Drilling
Screw - White
Panel (Long)
FIGURE 1.10
Fasten the Panel (Long) to the Bottom Channel with ten
White Wafer-Head Self-Drilling Screws.
FIGURE 1.12
FIGURE 2.0
DOOR INSTALLATION
Fit the Door Stop over the front Panel (Short). The Door Stop
tab fits into the slot in the Bottom Channel.
X
X
X
XXX
X - Anchoring locations
X
X
Check the walls are square by measuring the distance from
corner-to-corner (dashed lines, Figure 1.13). The diagonal
measurements should be equal for the walls to be square.
FIGURE 1.13
Bottom Channel
Door Jamb
Hex-Head Self- Drilling
Screw - Colour
Right side
Panel (Long)
Packaging
Material
Sheetmetal Screw - Colour
Sheetmetal Screw - Colour
Inside of Shed
Outside of Shed
1
3
4
Panel
Sheetmetal Screw
- White
2
Door Stop
Bottom Channel
Hex-Head Self-
Drilling Screw - Colour
FIGURE 2.2
Fit the Door Jamb over the right side Panel (Long). Fasten
the Door Jamb to the Bottom Channels using two coloured
Hex-Head Self-Drilling Screws.
Note: Use a piece of packaging material to keep the door
supported in the open position.
FIGURE 2.3
Fasten one coloured Sheetmetal Screw through the Door
Jamb and Door Stop and into the Panels from the inside of
the shed.
FIGURE 3.0
WALL ASSEMBLY
Replicate steps 1.2 to 1.12 and 2.3 to build up the next three
layers of Panels. Panels lap together as below (Figure 3.0).
Ensure Panels are assembled in the order of Front, Left,
Right then Rear.
Use white Sheetmetal Screws to fasten panels together.
Fasten the Door Stop to the Bottom Channel using two
coloured Hex-Head Self-Drilling Screws.
FIGURE 2.1
Barge Panel - Left
Barge Panel - Right
3rd Panel Layer
4th Panel Layer
1st Panel Layer
2nd Panel Layer
Sheetmetal
Screw - White
Wall Brace
Wall Brace
Panel (Long)
Wall Brace
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
FIGURE 3.3
Assemble the remaining Panel layers.
Note: For the sixth Panel layer, fit a Barge Panel (Left) and
Barge Panel (Right).
FIGURE 3.2
A Wall Brace is installed along the Panel (Long) laps between
the 3rd and 4th panel layers.
Fit the Wall Braces under the panel laps (Figure 3.2). Fasten
through the Panel and into the Wall Brace with six white
Sheetmetal Screws in each Panel. Fasten the Panel (Front)
with four white Sheetmetal Screws.
3rd Panel Layer
4th Panel Layer
1st Panel Layer
2nd Panel Layer
Sheetmetal
Screw - White
FIGURE 3.1
When installing the Panels of the fourth layer, only fasten
three White Sheetmetal Screws in each corner. Do not
fasten the middle six white Sheetmetal Screws of the Panels.
Sheetmetal
Screw - Colour
Barge Panel
Roof Flashing (Lower)
Roof Flashing (Lower)
Door Stop
Door Jamb
Roof Flashing (Lower)
Gutter
Downpipe Outlet
Rivet
Apply Silicone to
underside of Outlet
Apply Silicone to
gaps in Gutter
Sheetmetal Screw
- White
Roof Flashing (Lower)
Panel (Front)
View looking upwards from inside of shed
FIGURE 4.1
Fasten two coloured Sheetmetal Screws through the Barge
Panels and into the Roof Flashing (Lower) at both ends.
FIGURE 4.0
ROOFING INSTALLATION
Fit the Roof Flashing (Lower) to the Door Stop and Door
Jamb. The slots in the underside of the Roof Flashing (Lower)
fit over the tabs of the Door Stop and Door Jamb.
FIGURE 4.3
Apply silicone to the underside of the Downpipe Outlet. Fit
the Downpipe Outlet into the Downpipe Opening in the
Gutter. Rivet the Downpipe Outlet in place using four Rivets.
Apply silicone to the inside gaps of both Gutter ends.
FIGURE 4.2
From inside of the shed, fasten three white Sheetmetal
Screws through the front Panel (Short) and up into the Roof
Flashing (Lower).
Hex-Head Self-Drilling
Screw with Washer - Colour
Downpipe
Strap
Panel Lap
Hex-Head Self-
Drilling Screw - Colour
Downpipe
Gutter
Sheetmetal
Screw - White
Sheetmetal Screw - Colour
Barge Panel
Gutter
Panel (Long)
Gutter fits under
Barge Panel
HANDI-POD® GARDEN SHED INSTALLATION GUIDE
FIGURE 4.6
Position the Downpipe Strap against the Panel lap. Fasten
the Downpipe Strap to the rear Panel (Long) using two
coloured Hex-Head Self-Drilling Screws with Washers.
FIGURE 4.7
Fit the Downpipe over the Downpipe Outlet and hard
against the underside of the Gutter. Fasten the Downpipe
to the Downpipe Strap using two Coloured Hex-Head Self-
Drilling Screws.
FIGURE 4.5
Fasten one coloured Sheetmetal Screw through the Barge
Panel and into the Gutter at both ends.
Fasten six white Sheetmetal Screws through the Gutter and
into the rear Panel (Long).
FIGURE 4.4
Fit the Gutter over the rear Panel (Long). Ensure the Gutter
fits under the Barge Panels.
Rivet
Downpipe
Roof Sheet
Barge Panel
Roof Sheet
Barge Panel Gutter
Ensure correct Sheet lapping
Sheetmetal
Screw - Colour
Roof Flashing
(Upper)
Roof Flashing
(Lower)
Roof Flashing
(Upper)
Hex-Head Self-Drilling
Screw - Colour
Gutter
Roof Sheet in-line with
Roof Flashing - Lower
Hex-Head Self-Drilling
Screw - Colour
Roof Flashing - Lower
Roof Sheet
Gutter
Side Profile of Roof Flashing - Lower Side Profile of Gutter
FIGURE 4.8
Drill two Ø3.5mm holes through the Downpipe and into
the Downpipe Outlet. Rivet the Downpipe to the Downpipe
Outlet with two coloured Rivets.
FIGURE 4.9
Fit the Roof Sheets onto the Roof Flashing (Lower) and
Gutter. Ensure the Roof Sheets fit under the Barge Panels.
FIGURE 4.11
Fit the Roof Flashing (Upper) over the Roof Sheets and Roof
Flashing (Lower). Fasten two coloured Sheetmetal Screws
through the Roof Flashing (Upper) and into the Roof Flashing
(Lower) at both ends.
FIGURE 4.10
Ensure the ends of the Roof Sheets are in line with the Roof
Flashing (Lower). Fasten coloured Hex-Head Self-Drilling
Screws with Washers through every second Roof Sheet pan
into the Roof Flashing (Lower) and Gutter.
M8 Masonry Anchor
Anchor Plate
X
X
X
XXX
X - Anchoring locations
X
X
Hex-Head Self-Drilling Screw
with Wahser- Colour
Hex-Head Self-
Drilling Screw with
Wahser - Colour Barge Panel
Door Stop
Wafer-Head Self-
Drilling Screw - 22mm
Locking
Washer
Locking
Screw
Door Handle
Tongue
Door Handle
Handle Mount
BROCHPGSHP2
« SCAN THIS QR CODE TO FIND A STRATCO NEAR YOU
1300 155 155
stratco.com.au
All brands and logos/images accompanied by ® or ™ are trade marks of Stratco (Australia) Pty Limited. ® Copyright Jan 2023
FIGURE 5.2
Refer to anchoring locations (Figure 5.1). Using the holes in
the Anchor Plates as a guide, drill a hole into the concrete
slab through all six Anchor Plates using a 10mm Masonry
Drill Bit. Fix all six Anchor Brackets to the concrete slab using
six M8x47 Masonry Anchors (Figure 5.2).
MAINTENANCE
Regular maintenance is essential to maintain the good
looks of the Handi-Pod
®
Garden Shed and to ensure
you receive the maximum lifespan possible. Washing
with clean water must be frequent enough to prevent
the accumulation of dust, salts, and pollutants which
may reduce the life of the product. No material that
retains water (such as dirt or paving sand) should be
placed against the Handi-Pod
®
Garden Shed. Refer to
the ‘Selection, Use and Maintenance’ brochure on the
Stratco.com website for more information.
Move the Handi-Pod® Garden Shed into its final position.
Check the walls are square by measuring the distance from
corner-to-corner (dashed lines, Figure 5.1). The diagonal
measurements should be equal for the walls to be square.
FIGURE 5.1
FIGURE 4.12
Fasten coloured Hex-Head Self-Drilling Screws with
Washers through the four pilot holes of both Barge Panels
and into the Roof Sheets. Fasten a coloured Hex-Head Self-
Drilling Screw with Washer through the Door Stop and into
the Panel (Short).
FIGURE 5.0
FINAL ASSEMBLY
Fasten the Door Handle to the Handle Mount with two
22mm Wafer-Head Self-Drilling Screws.
Slide the Door Handle Tongue all the way up the Door Handle
shaft, ensuring the Door Tongue is oriented perpendicular
to the Handle.
Tighten the Door Tongue screw on the Door Handle shaft to
secure the Door Tongue in place. Slide the Locking Washer
all the way up the Door Handle shaft to secure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Stratco Handi-Pod™ HP2 Guida d'installazione

Tipo
Guida d'installazione