Gaggenau AI442720 Guida d'installazione

Gaggenau

Installation instructions..........................2

Instructions d’installation.....................20

Instrucciones de instalación................38

AI 442 720

Hood

Hotte aspirante

Campana extractora

2

Table of Contents

Installation instructions

Safety Definitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this

warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this

warning.

NOTICE: This indicates that damage to the appliance

or property may occur as a result of non-compliance

with this advisory.

Note: This alerts you to important information and/or

tips.

3

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: LEAVE THESE INSTRUCTIONS WITH

THE APPLIANCE AFTER INSTALLATION IS

COMPLETE.

IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE

LOCAL ELECTRICAL INSPECTOR'S USE.

WARNING

If the information in this manual is not followed exactly,

fire or shock may result causing property damage or

personal injury.

WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or maintenance

can cause injury or property damage. Refer to this

manual for guidance. All other servicing should be done

by a qualified technician.

WARNING

WARNING – TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING

‒ Installation work and electrical wiring must be done

by qualified person(s) in accordance with all

applicable codes and standards, including fire-

rated construction.

‒ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guideline and safety standards such as those

published by the National Fire Protection

Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code

authorities.

‒ When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

‒ Ducted fans must always be vented to the outdoors.

WARNING

The applicable regulations of the energy supply

companies and the regional construction regulations

must be observed when installing the hood.

WARNING

Risk of fire

Grease deposits in the grease filter can catch fire.

Never work with a naked flame near the appliance (e.g.

flambéing). Install the unit near a heat-producing

appliance for solid fuels (e.g. wood or coal) only if there

is a closed, non-detachable cover. There must be no

flying sparks.

WARNING

Risk of fire

Operating several gas burners at the same time gives

rise to a great deal of heat. The ventilation appliance

may become damaged or catch fire. The ventilation

appliance must only be combined with gas burners that

do not exceed the maximum total output of 61,000 Btu/

hr (18 kW). If 41,000 Btu/hr (12 kW) is exceeded, the

local regulations concerning room ventilation, room

size, and combination with ventilation devices in exhaust

and recirculating operation must be heeded.

WARNING

To reduce risk of fire and to properly exhaust air, be

sure to duct air outside. Do not vent exhaust air into

spaces within walls, ceilings, attics, crawl spaces or

garages.

WARNING

To reduce the risk of fire, use only metal ductwork.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

4

WARNING

When the hood is operated in exhaust-air mode

simultaneously with a different burner which also makes

use of the same chimney (such as gas, oil or coal-fired

heaters, continuous-flow heaters, hot-water boilers) care

must be taken to ensure that there is an adequate

supply of fresh air which will be needed by the burner

for combustion.

Safe operation is possible provided that the under

pressure in the room where the burner is installed does

not exceed 4 Pa (0.04 mbar).

This can be achieved if combustion air can flow through

non-lockable openings, e.g. in doors, windows and via

the air-intake/exhaust-air wall box or by other technical

measures, such as reciprocal interlocking, etc.

WARNING

Avoid carbon monoxide poisoning – Provide adequate

air intake so combustion gases are not drawn back into

the room.

An air-intake/exhaust-air wall box by itself is no

guarantee that the limiting value will not be exceeded.

Note: When assessing the overall requirement, the

combined ventilation system for the entire household

must be taken into consideration. This rule does not

apply to the use of cooking appliances, such as

cooktops and ovens.

CAUTION

For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

Risk of damage from condensation back flow. Install

exhaust vent at a slight downward slope away from the

appliance (1° slope).

Appliance Handling Safety

Unit is heavy and requires at least two people or proper

equipment to move.

Hidden surfaces may have sharp edges. Use caution

when reaching behind or under appliance.

WARNING

Risk of injury

The appliance may fall from the wall if it is not attached

properly. All fastening components must be fixed firmly

and securely in place.

Safety Codes and Standards

This appliance complies with the latest version of one or

more of the following standards:

▯ UL 507 - Electric Fans

▯ CAN/CSA C22.2 No. 113 - Fans and Ventilators

It is the responsibility of the installer to determine if

additional requirements and/or standards apply to

specific installations.

Electric Safety

WARNING

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the

electric current.

This appliance is equipped with a cord having a

grounding wire with a grounding plug. The plug must be

plugged into an outlet that is properly installed and

grounded.

WARNING

Improper grounding can result in a risk of electric

shock. Consult a qualified electrician if the grounding

instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord

is too short, have a qualified electrician install an outlet

near the appliance.

WARNING

Before you plug in an electrical cord or turn on power

supply, make sure all controls are in the OFF position.

5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

For appliances equipped with a cord and plug, do not

cut or remove the ground prong. It must be plugged into

a matching grounding type receptacle to avoid electrical

shock. If there is any doubt as to whether the wall

receptacle is properly grounded, the customer should

have it checked by a qualified electrician.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

WARNING

To reduce the risk of fire or electric shock, do not use

this fan with any solid-statespeed control device.

Installer – show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned

ON accidentally.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

‒ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

‒ Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be sure your appliance is properly installed and

grounded by a qualified technician. Installation,

electrical connections and grounding must comply with

all applicable codes.

WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges. The

connection cable can be damaged. Do not bend or

pinch connection cables during installation.

Related Equipment Safety

Remove all tape and packaging before using the

appliance. Destroy the packaging after unpacking the

appliance. Never allow children to play with packaging

material.

The appliance is only guaranteed safe to use if installed

by a specialist in accordance with these installation

instructions. The installer is liable for any damage

resulting from incorrect installation.

Never modify or alter the construction of the appliance.

For example, do not remove leveling legs, panels, wire

covers or anti-tip brackets/screws.

State of California Proposition 65

Warnings

WARNING

This product contains chemicals known to the State of

California to cause cancer, birth defects or other

reproductive harm.

6

Installation preparation

9 CAUTION

Ensure that there are no electric wires, gas or

water pipes in the area where holes are to be

made.

Checking the ceiling

▯ The ceiling must be flat, horizontal and adequately

load-bearing.

▯ The depth of the bore holes must be the same

length as the screws. The wall plugs must have a

secure grip.

▯ The enclosed screws and wall plugs are suitable for

solid brickwork. Suitable fasteners must be used

for other structures (e.g. plasterboard, porous

concrete, poroton bricks).

▯ The max. weight of the extractor hood is 198 lbs

(90 kg)

.

General notes

9 WARNING

Risk of death

Risk of poisoning from flue gases that are drawn

back in. The exhaust air must not be conveyed

into a functioning smoke or exhaust gas flue or

into a shaft that is used to ventilate installation

rooms that contain heating appliances. If the

exhaust air is to be conveyed into a non-

functioning smoke or exhaust gas flue, you must

obtain the consent of the heating engineer

responsible.

Exhaust air mode

Note: Ventilation may not exit through an already

operational smoke or exhaust chimney, nor a duct used

for ventilating furnace installation areas.

▯ If the ventilation is intended to pass through a

smoke or exhaust that is not in operation, the

responsible area heating inspector must give

approval.

▯ If the ventilation passes through an external wall,

use a telescope wall sleeve.

Ventilation line

Note: The appliance manufacturer does not assume any

warranty for complaints attributable to the pipe section.

▯ The appliance achieves its optimum performance

with a short, straight exhaust air pipe and as large a

pipe diameter as possible.

▯ As a result of long rough exhaust air pipes, many

pipe bends or pipe diameters that are smaller than

6" (150 mm), the optimum extraction performance is

not achieved and fan noise is increased.

▯ The pipes or hoses for laying the exhaust air line

must be made of non-combustible material.

▯ Use sealing strip for deviating pipe diameters.

▯ An inner diameter of 6" (150 mm), but at least 4¾"

(120 mm), is recommended.

NOTICE: Risk of damage from condensation back flow.

Install exhaust vent at a slight downward slope away

from the appliance (1° slope).

7

Electrical connection

9 WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges.

The connection cable can be damaged. Do not

bend or pinch connection cables during

installation.

The required connection information is on the

appliance's identification plate.

This appliance meets EC radio interference

suppression requirements.

This appliance may only be connected to a correctly

installed grounded socket.

Attach the grounded socket inside the flue duct if

possible.

▯ The grounded socket should be connected via its

own circuit.

▯ If the grounded socket is no longer accessible after

installing the appliance, an all-pole isolating switch

(e.g. circuit breaker, fuses, and contactors) with at

least a 3 mm contact gap must be included in the

installation.

Before You Begin

Tools and Parts Needed

▯ Measuring tape

▯ Pencil

▯ Torx screwdriver TX20

▯ Drill with the following bits: 5/16" (8 mm)

▯ Spanner, 7 mm

▯ Spirit-level

▯ Aluminum tape (DO NOT use insulating tape)

▯ Exhaust channel (configuration depends on the

installation situation)

▯ Additional sheet metal screws (if necessary for

installation of the exhaust air duct)

Parts Included

All models

8

Models with circulating-air mode

Ducted operation

Accessory: Remote fan unit

$$

$'

$'

$5

9

Appliance dimensions

Models with air extraction mode

Models with air recirculation mode

 PP



é







è¼ʚ



ë



ç¼ʓʘ

èç¼ʓʘ



èè¼ʓʘ





ç¼ʓʘ





ç¼ʚ



èʌ¼ʓʘë



èʊ¼ʓʘ



ê



ê

è¼ʓʘ



ç¼ʚ



èʌ¼ʓʘë



ê



é

 PP







è¼ʚ

ç¼ʓʘ







ê



èʊ¼ʓʘ

è¼ʓʘ

èè¼ʓʘ



èç¼ʓʘ





ë



ç¼ʓʘ

10

Safety clearances

9 WARNING

Risk of fire

Grease deposits in the grease filter may catch

fire. The specified safety distances must be

observed in order to prevent an accumulation of

heat. Observe the specifications for your cooking

appliance. If gas and electric cooktops are

operated together, the largest specified distance

applies.

Only one side of the appliance may be installed

directly next to a high-sided unit or a wall. The

distance between the appliance and wall or high-

sided unit must be at least 2" (50 mm).

The minimum distance between the supporting surface

for the cooking equipment on the hob and the lowest

part of the range hood must be not less than 30 "

(760 mm) from electric cookers and 30 " (760 mm) from

gas or mixed cookers.

If the instructions for installation for the gas hob specify

a greater distance, this must be adhered to.

Installation

Transport securing device

The supporting frame is secured for transport using

self-tapping screws. Remove these self-tapping screws

before installation.

Fitting the upper support frame

1 Before installation, establish the total height of the

support frame.

Note: The height of the support frame can be

adjusted in steps of ¾" (20 mm).

2 Mark the positions of the six screws on the ceiling.

Note: Ensure that the support frame is in the

correct position. The appliance has one control

panel on the open side of the support frame. The

other control panel is located on the opposite side.

3 Drill the holes and push in the wall plugs so that

they are flush with the wall.

4 Use four screws to fit the reinforcement plate to the

inside of the support frame.

5 Use six screws to fasten the upper support frame to

the ceiling.

!



DERYHHOHFWULF

VXUpOHFWULTXH

VREUHHOpFWULFR

DERYHJDV

VXUJD]

VREUHJDV

11

Fitting the lower support frame

without using an extension

1 Ensure that the lower support frame is in the

correct position.

Note: Position the open side of the lower support

frame opposite the open side of the upper support

frame.

2 Slide the lower support frame into the upper

support frame and use 16 screws to secure it at the

established total height.

Notes

‒ Select the mounting holes in such a way that a

maximum clearance is achieved between the

screws. The purpose of this is to ensure stability.

‒ Leave open at least one mounting hole between the

screws.

Fitting the lower support frame using

an extension

1 Slide each part of the extension over the outside of

the upper support frame and use 16 screws to fit

them to the upper support frame..

2 Ensure that the lower support frame is in the

correct position.

Note: Position the open side of the lower support

frame opposite the open side of the upper support

frame.

12

3 Slide the lower support frame up into the extension

and use 16 screws to secure it at the established

total height.

4 Fit two reinforcing brackets.

 PP



ʎ¼ʓʘè¼ʚ

13

Installing the appliance

1 For recirculation mode units only: Fit filters to both

sides of the AA 442 810 air recirculation module.

Slide the air recirculation module into the support

frame from below and hook it in place. Secure it

with two screws.

2

For combination with internal remote fan unit

AR 400 743 only:

Unscrew the cover plate from the

ventilation hood: Loosen the four screws, remove

the cover plate and screw the four screws in again.

Slide the remote fan unit into the ventilation hood

from above. Use four screws to secure it in place.

14

Connect the mains cable and control cable to the

control module.

3 For a combination with external remote fan unit

AR4.. only:

Use the network cable to connect the

external remote fan unit and the ventilation hood’s

control module. The plug must snap into place.

Connect the mains cable to the control unit.

Note: The X1 and X2 connection sockets are

identical.

4 Slide the ventilation hood up into the support frame

from below and hook it into the two angle brackets

(a).

Note: Ensure that the mains cable is not trapped.

5 Align the ventilation hood so that it is straight and

use seven screws to fasten the ventilation hood to

the support frame.

D

15

Connect appliance

Notes

‒ With operation in extraction air mode , a back-

pressure flap should be installed. If no back-

pressure flap is included with the appliance, it can

be ordered from a specialist retailer.

‒ If the exhaust air is conveyed through the outer wall,

a telescopic wall box should be used.

‒ If an aluminum pipe is used, smooth the connection

area beforehand.

Establishing the connection for the exhaust air

1 Recirculation mode units with internal remote fan

unit AR 400 743:

Attach the exhaust air pipe directly

to the fan motor's air pipe connector (A).

2

Extraction mode units with internal remote fan unit

AR 400 743:

Attach the exhaust air pipe directly to

the fan motor's air pipe connector (A).

$5

$

%

$5

$

%

16

3

Extraction mode units with external remote fan unit

AR 4..:

‒ Unscrew the connecting pieces from the cover

plate in the ventilation hood.

‒ Secure the exhaust air pipe to the connecting

piece (A).

‒ Screw the connecting piece to the cover plate in

the ventilation hood.

4 Connect it to the air extractor opening (B).

5 Seal the joints appropriately.

Connecting the power supply

1 Plug the mains plug into the grounded socket.

2 If a fixed connection is required, please follow the

instructions in the Electrical Connection section.

Attaching flue duct

9 WARNING

Risk of injury

Components inside the appliance may have sharp

edges. Wear protective gloves.

1 Remove the protective film from the flue ducts.

2 Place both parts of the upper flue duct on the

appliance such that they fit together.

Model with air extraction mode

Models with air recirculation mode

3 Push the upper flue duct up and use two screws to

secure it at the top.

$5

$

%

17

Model with air extraction mode

Models with air recirculation mode

4 Place both parts of the lower flue duct on the

appliance such that they fit together.

5 Fit the grease filter.

18

Additional switching output

Work must only be carried out on the additional

switching output by a qualified electrician in

accordance with the country-specific requirements and

standards.

The appliance has an additional switching output X16

(potential-free contact) that can be used to connect

other appliances, such as a ventilation system that is

available at the installation site. The contact is closed

when the fan is switched on, and is opened when the

fan is switched off.

The switching output is located under a cover. Maximum

switching power 30 V/1 A (AC/DC). The signal that is

connected to the contact must correspond to class of

protection 3.

Networked operation

Several appliances can be networked together. The

light and fan on each of the appliances are operated

synchronously.

Connect the appliances in series via the connector

sockets X1 and X2 (equal value). The sequence of the

networking does not have any effect. If the enclosed

network cables are too short, use a commercially

available network cable (min. Cat. 5, shielded).

Maximum number of networked appliances: 20. Total

length of all of the network cables: 40 m. During the

initial installation, a qualified electrician must check

that the system functions correctly.

If one of the networked appliances fails (power

interruption, network cable disconnected), this leads to

the fan function being blocked for the entire system. All

of the buttons on the appliance flash.

When changing the configuration, the system must be

re-initialized:

1 Unscrew the cover plate.

2 Press and hold the reset button until both LEDs

light up continuously (approx. 5 seconds). Then

release the button within 5 seconds.

3 Screw on the cover plate.

4 After initialization, have a qualified electrician

check that the system functions correctly.

Connect Electrical Supply

9 WARNING

Risk of electric shock

Parts inside the appliance can have sharp edges.

The connection cable can be damaged. Do not

bend or pinch connection cables during

installation.

Refer to data plate for more information. See "Service"

for data plate location.

The branch-circuit breakers ampacity, the wire sizes and

the connections must be conform to the requirements of

the National Electrical Code or Canadian Electrical

Code and all local codes and ordinances.

This appliance is connected with a plug

▯ Plug has to be conform with NEMA

CONFIGURATIONS FOR PLUGS AND

RECEPTACLES.

▯ The appliance must be properly grounded.

▯ Plug must be rated not less than type 6-20 P (2-pole

3-wire grounding).

▯ Only a qualified electrician should connect the

plug.

▯ Install a socket outlet earthed in accordance with

regulations approx. 27" (700 mm) above the floor

behind the appliance. The socket outlet must still

be accessible after installation.

19

Removing the appliance

1 Remove the grease filter.

2 Loosen the flue duct.

3 Disconnect the appliance from the power supply.

4 Loosen the exhaust air lines.

5 Undo the fastening screws.

6 Remove the appliance.

Customer service

If your appliance needs repairs, our customer service is

there for you. We work hard to help solve problems

quickly and without unnecessary service calls, getting

your appliance back up and running correctly in the

least amount of time possible.

When you call, please indicate the product number

(E-Nr.) and serial number (FD-Nr.) so that we can

support you in a qualified manner. The identification

plate listing the numbers can be found inside of the

appliance (remove metal grease filter to find it).

To avoid having to search for a long time when you need

it, you can enter your appliance data and the customer

support telephone number here.

Please read the use and care instructions provided with

your appliance. Failure to do so may result in an error in

using the appliance. This could result in a service call

that instead of fixing a mechanical issue is only needed

for customer education. Such calls are not covered by

the appliance warranty.

Please find the contact data of all countries in the

enclosed customer service list.

To book an engineer visit and product advice

You can rely on the manufacturer’s expertise. Rest

assured that the repair will be handled by trained

service technicians who have the original replacement

parts for your appliance.

E-Nr. FD-Nr.

Customer Service

O

USA 877 442 4436

toll-free

CANADA 877 442 4436

toll-free

20

Table de Matières

Instructions d’installation

Définitions de Sécurité

9 AVERTISSEMENT

Le non-respect de cet avertissement peut

entraîner la mort ou des blessures graves.

9 ATTENTION

Le non-respect de cet avertissement peut

entraîner des blessures mineures ou modérées.

AVIS : Vous indique que des dommages à l'appareil ou

aux biens peuvent survenir si vous ne respectez pas cet

avertissement.

Remarque : Vous signale des informations importantes

ou des conseils.

La pagina sta caricando ...

Gaggenau AI442720 Guida d'installazione

Questo manuale è adatto anche per

Gaggenau AI442720 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti