Inventor M3GHP290-12 Portable Air Conditioning Systems Manuale utente

PORTABLE

MODELS:

M3GHP290-12

M3GHP290-12BS

AIR CONDITIONING SYSTEMS

• USER’S MANUAL

• ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ

• MANUAL UTILIZATORULUI

• BEDIENUNGSANLEITUNG

• MANUEL D'UTILISATEUR

• MANUALE DELL'UTENTE

• MANUAL DE USARIO

ENGLISH | ΕΛΛΗΝΙΚΑ | ROMANA | DEUTSCH |

FRANÇAIS | ITALIANO | ESPAÑOL

2EN

Contents

Safety Precautions ................................................................................................................................................3

Cautions ...................................................................................................................................................................4

Warnings (for using R290/R32 refrigerant only) ...........................................................................................5

Preparation .......................................................................................................................................................... 10

Installation ............................................................................................................................................................ 11

Operation ............................................................................................................................................................. 14

Maintenance ....................................................................................................................................................... 17

Troubleshooting ................................................................................................................................................ 18

Design and Compliance Notes ....................................................................................................................... 19

Sociable Remark ................................................................................................................................................. 20

EN 3

|Safety Precautions

WARNING: “Safety Hazard Symbol”, it is very important to please pay close attention to the

below, to avoid any serious injury.

WARNING: To avoid any serious injuries or possible unit damage, please read carefully and

follow the below safety guidelines:

- The installation of this unit must be according to this manual, as improper installation may cause

water leakage, electrical shock or even a re.

- Use only included parts and accessories, and the specied tools for the installation of your

portable air conditioner. The use of parts that are not included in this package may result to water

leakage, electrical shock, re, injury and possible property damage.

- Be certain that the outlet in use, is properly grounded and that of the correct voltage. The three-

prong power cord is designed to protect against shock. Information regarding voltage may be

found on the nameplate of your unit.

- This unit must be connected to a properly grounded power supply. If the power supply is not

grounded or protected by a fuse or a circuit breaker (the correct fuse is determined by the

maximum current of the unit, which is located on the nameplate of the device) it is strongly

advised to have a professional qualied electrician install the proper power supply.

- Install on a at and sturdy oor. Failure to install in this manner could result in damage, excessive

noise and even vibration.

- This device should be placed clear of any obstructions to ensure its correct and proper function

and to avoid any possible hazards.

- DO NOT use an extension cord or modify the length of the cord in any way, to power the unit.

- DO NOT combine a single power outlet with other electrical appliances. Irregular power supply

may cause electric shock and a possible re.

- DO NOT install this unit in a very humid room such as a bathroom facility or a laundry room.

Excessive exposure to water may cause the internal electrical components to short circuit.

- DO NOT install in a location exposed to a combustible gas, as this could result to a re.

- The device is equipped with casters for easy mobility. It is suggested not to be used on thick

carpets, as this may cause its tripping.

- DO NOT operate this unit if it has been dropped or damaged in any way.

- For models with heating capabilities, there should be at least 1 meter clear space from any

combustible materials.

- Do not touch this unit with wet or damp hands or while barefoot.

- If the portable air conditioner is knocked over while operating, turn o and unplug from the power

socket immediately. Examine the device ensuring there is no visible damage. If you suspect that

the unit has been damaged, it is necessary to contact a technician or customer support for further

assistance.

- In the event of a thunderstorm, it is suggested to turn o the unit as there is the possibility of

damage due to unsteady power supply.

- Your portable air conditioner should be operated in such a manner, so as to be protected from

moisture. Do not position the unit in an area where possible tripping into water may occur. In this

event, unplug immediately.

- All wiring must be performed strictly in accordance to the wiring diagram which is located

internally.

- The circuit board of the unit (PCB) is designed with an overcurrent protection fuse. Specications

of the fuse are printed on the circuit board, in this manner: T3.15A/250V.

4EN

|Cautions

CAUTIONS

- This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

- This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities or lack of experience and knowledge, unless supervised, or

given instruction concerning the use of the appliance by a person responsible for their safety.

(Applicable for non- European countries).

- Minors should be supervised to ensure that there is no mishandling od the device. It is strongly

advised that minors should be supervised when around this unit at all times. If the supply cord

is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualied

person in order to avoid possible hazard.

- Prior to cleaning or maintaining the air conditioner, please make sure the unit is initially turned o

and disconnected from the mains.

- Do not remove any xed covers. If you suspect the unit is not operating properly or if it has been

dropped or damaged in any way it should never be used.

- Do not place the power cord under any carpets, rugs, runners or similar coverings, under

furniture or other appliances. The power cord should be placed in such a manner that accidental

tripping may be avoided.

- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a

similarly qualied person in order to avoid a hazard.

- To reduce the risk of possible re or electric shock, do not combine the use of your device with any

Solid- State speed control device (dimmer).

- This unit must be installed in accordance to the national wiring regulations.

- For the proper maintenance of this unit, please contact an authorized technician.

- If any installation is required, please contact an authorized professional installer.

- The inlet or outlet grilles should never be obstructed.

- This unit should be operated only, as per the instructions of this manual, and not for any other

use.

- Prior to cleaning, power o the unit and unplug.

- In the case of any abnormal behavior (e.g.. a burning smell), disconnect power intermediately and

contact your local dealer.

- Do not operate the buttons of the digital control panel with anything other that your hands.

- Do not turn ON/OFF this device by plugging or unplugging the power cord.

- This unit should never be cleaned with the use of hazardous chemicals. The unit should never be

operated in the presence of inammable substances such as pure alcohol, petrol etc.

- Always relocate your portable air conditioner in a vertical position and should always be placed in

a vertical position.

- If the supply cord is damaged, the manufacturer, its service agent or similarly qualied persons

must replace it, in order to avoid a hazard.

- Grip the power plug properly when pulling out of the power socket.

- When inoperative for a long period of time please power o and unplug.

Warning: Low pressure conditions may occur in the area. The device is not recommended for

use by people with chronic respiratory problems.

EN 5

|Warnings (for using R290/R32 refrigerant only)

- Do not use any other means other than the recommended to expedite the defrosting process or

to perform a cleaning of the unit, other than those recommended by the manufacturer.

- This device should never be stored in an area in combination with other ignition sources (for

example: a gas appliance an electrical heater, open ames etc.)

- Do not attempt to penetrate the unit with a tool or try to burn.

- Be extra cautious as refrigerant gas may be odorless.

- Appliance 12000 Btu/h should be installed, operated and stored in a room with a oor area larger

than 11m 2.

Appliance 10000 Btu/h, 9000 Btu/h should be installed, operated and stored in a room with a oor

area larger than 10m 2.

Appliance 12000 Btu/h,10000 Btu/h should be installed, operated and stored in a room with a

oor area larger than 12m 2.

- It is necessary to always comply with national gas regulations.

- Keep air ventilation clear of any obstructions.

- The unit should be placed in storage in such a manner as to prevent any mechanical damage from

occurring.

- Always operate this unit in a well- ventilated area, where the room size corresponds to the

specications of the device for optimal performance.

- Any persons involved with the operation and handling of the refrigerant circuit of this unit,

should be certied by the related accredited industry, and authorized as competent to handle

refrigerants, safely, and in accordance to the safety standards of the industry.

- Servicing should be performed only by a certied technician as per the Mnaufacturers

reccomendations. Any maintenance or repair required, should be performed by skilled personnel

who are competent in the use of ammable refrigerants.

Caution: Risk of re/ ammable materials

(Required for R32/R290 units only) IMPORTANT NOTE: Please read this manual

carefully prior to installing and operating your

device! It is recommended to keep this manual

for future reference.

Description of displayed Symbols (*Only applicable to units with R32/R290 Refrigerant)

WARNING This symbol indicates the use of a ammable refrigerant. If any leakage

occurs, or if exposed to an external ignition source, a re risk is possible.

CAUTION This symbol indicates that the user’s manual should be read carefully.

CAUTION This symbol indicates that a professional service technician should handle

this unit with reference to the user’s manual.

CAUTION This symbol indicates the presence of a user’s or installation manual.

6EN

1. Transport of equipment containing

ammable refrigerants See transport

regulations

2. Marking of equipment using signs See local

regulations

3. Disposal of equipment using ammable

refrigerants See national regulations.

4. Storage of equipment/appliances

The storage of equipment should be in

accordance as per the user’s manual.

5. Storage of packed (unsold) equipment

The storage of the package should be

constructed in such a manner that if any

mechanical damage to the equipment will not

result ina leak of the refrigerant.

6. Information on Servicing

1) Checking the area

Upon initial work, regarding systems containing

ammable refrigerants, mandatory safety

checks are required to ensure that the risk

of possible ignition is minimized. Prior to

any repairing to the refrigerant system, the

following

2) Work procedure

Any handling should be performed under a

controlled procedure as to minimize the risk

of ammable gas being present while work is

being performed.

3) General work area

All relative maintenance sta and all others

working in the area, should be clearly

instructed, on the nature of the procedure.

Any maintenance in conned spaces must

be avoided. The space around the work- area

should be securely sectioned o. Conrm that

the conditions within the area, are safe and the

ammable material is controlled.

4) Prior to and during work operation, the

area should be checked and monitored by an

appropriate refrigerant detector, also ensuring

the technicians to be aware of potentially

ammable materials in the atmosphere. It is

very important that the refrigerant detector

being used is suitable for the usage with

ammable refrigerants.

5) Presence of re extinguisher

If any work that involves heat, is to be

conducted, the appropriate re extinguishing

equipment should be always available. A dry

powder or CO2 re extinguisher should be

available adjacent to the charging area.

6) No ignition sources

Work that is in relation to a refrigeration

system which involves exposing any pipe works

that contains or has contained ammable

refrigerant gases should be carried out be

no persons, as they may lead to the risk of a

re.All possible re hazards such as cigarette

smoking, must be kept far away from the site

of repair,installation removing and or disposal,

where the possibility of refrigerant gas may

be released to the atmosphere. Prior to the

performance of any work conducted, the area

around the equipment should be monitored

and checked to be certain that no ammable

hazards or ignition risks are present. NO

SMOKING signs are mandatory and must be

displayed..

7) Ventilated area

Prior to any work performed, be certain that

the area is well ventilated or open. Constant

ventilation while any work is carried out is

necessary. Ventilation should safely disperse

any possible refrigerant leak externally into the

atmosphere.

8) Checks to the refrigeration equipment

Where electrical components are being

changed, they should be t for purpose and

with the correct specications. Manufacturer’s

maintenance and Service Guidelines should

be followed at all times. If there is any doubt,

please consult with the manufacturer’s

Technical Debt for assistance. The following

checks should always be performed in regard

to installations using ammable refrigerants:

The charge size is in accordance with the room

size, in which the refrigerant parts are installed.

Be certain the ventilation is operative and check

the outlets do not have any obstructions.

If there is a use of an indirect refrigerant

circuit, this secondary circuit should be

checked for any refrigerant being present. Any

markings to the equipment should be clear

and visible. Markings and signs that are not

clear should be corrected. Any refrigeration

pipe or components should be installed in

such a manner as to never be exposed to any

substance that may lead to the corrosion of

the refrigerant containing components, unless

these components are designed as resistant to

possible corrosion, or are corroded resistant.

9) Checks to electrical devices

|Warnings (for using R290/R32 refrigerant only)

EN 7

|Warnings (for using R290/R32 refrigerant only)

The repair and the maintenance to the electrical

components must include safety checks and

also component inspection procedures. If there

is any fault, that may compromise the safety of

the work applied, then no electrical supply shall

be connected to the circuit until it is corrected. If

the fault cannot be corrected immediately but it

is necessary to continue operation, a temporary

solution may be applied, such as the reporting

to the owner of the equipment, so all parties are

informed.

Initial safety checks shall include:

Capacitors are discharged, in a safe manner to

avoid any possible sparking. No active electrical

components and wirings are exposed while

charging, recovering or purging the system. That

there is continuity of earth bonding.

7. Repairs to sealed components

1) During any performed repairs to sealed

components, all electrical supplies must be

disconnected from the equipment prior to this

act. If it is necessary to have an electrical supply

to the equipment during its servicing, then a

leak detector should be applied as to warn if

there are any signs of potential hazards present.

2) There should be particular attention to

the following as to ensure, that by working on

electrical components there is no alteration

to the casing in such a way that the level of

protection is aected. This includes damage to

the cables, excessive number of connections,

terminals not designed to original specications,

any damage to seals, the incorrect tting of

glands, etc.

Ensure the unit is mounted securely.

Ensure that the seals or any sealing materials

have not degraded in such a manner as

to no longer serve its purpose, preventing

ammable gases entering the atmosphere. Any

replacement parts should be in accordance as

per the manufacturer’s specications.

NOTE: The use of silicon sealant may aect

the eciency of some types of leak detection

equipment. Safe components do not have to be

isolated prior to working.

8. Repair to intrinsically safe components

Do not apply any permanent inductive or

capacitance loads to the circuit without

ensuring that this will not exceed the

permissible voltage and current, allowed for the

equipment in use. Intrinsically safe components

are the only type that can be worked on, while

live in the presence of ammable atmosphere.

The test apparatus should be at the correct

rating. Any replacement of parts should be as

specied by the Manufacturer, as other parts

may result in an ignition of refrigerant gas from

a possible leak.

9.Cabling

Please check that cables are not subject to wear,

corrosion, excessive pressure, vibration, or any

other adverse environmental eects. Aging or

continual vibration, should also be taken into

account.

10. Detection of ammable refrigerants

Under no circumstance may a potential ignition

source, such as a halide torch or any detector

with the use of a ame, may be used.

11. Leak detection methods

The following leak detection methods are

acceptable for systems containing ammable

refrigerants.

Electronic leak detectors may be used to detect

ammable refrigerants. However, the sensitivity

may not be adequate, or it is possible it may

need re- calibration.

(Detection equipment should be calibrated in

a refrigerant- free area) It should be ensured

that the detector is not a possible ignition

source and is suitable for the refrigerant used.

Leak detection equipment should be set at a

percentage of the LFL of the refrigerant used.

Leak detection equipment should be set at

a percentage of the LFL of the refrigerant

and should be calibrated to the refrigerant

employed and the appropriate percentage

of gas (25% maximum) is conrmed. Leak

detection uids are suitable for use with

most refrigerants but the use of detergents

containing chlorine must be avoided as the

chlorine may react with the refrigerant and

corrode the copper pipe- work. If a leak is

suspected, all ames must be extinguished. If a

leakage of refrigerant is spotted which requires

brazing, all of the refrigerant shall be recovered

from the system, or isolated (by means of

shutting o the valves) in a part of the system

away from the leak. Oxygen free nitrogen (OFN)

should then be purged through the system

both before and during the brazing process.

12. Removal and evacuation

When interfering with the refrigerant circuit

8EN

in order to make any repairs or for any other

purposes, conventional procedures should

be applied. However, it is strongly suggested

that safe practice is followed, and ammability

should be taken under consideration.

The following procedure should be followed as

to:

Remove refrigerant,

Purge the circuit with inert gas,

Evacuate,

Purge again with inert gas,

Open the circuit by performing a cut or brazing.

The refrigerant charge should be recovered

into the assigned and correct recovery

cylinders, The system must be ushed with OFN

to render the unit safe, This process may be

repeated several times. The use of Compressed

air oxygen may not be used for this act.

Flushing may be achieved by breaking the

vacuum in the system with OFN and continuing

to ll until the working pressure has been

achieved, then venting to atmosphere, and

nally pulling down to a vacuum. This process

should be repeated until no refrigerant is left

within the system. When the nal OFN charge

is used, the system shall be vented down to

atmospheric pressure to enable any work to be

performed. This operation is absolutely crucial

if brazing operations on the pipe- work are

intended to take place.

Ensure that the outlet for the vacuum pump is

not close to any ignition sources and there is

plenty of ventilation available.

13. Charging procedures

In addition to conventional charging

procedures, the following requirements should

be followed.

Ensure that the contamination of dierent

refrigerants does not occur when using

charging equipment. Hoses or lines shall be as

short as possible to minimise t he amount of

refrigerant contained in them.

Cylinders shall be kept in an upright position.

Ensure that the refrigeration system is

earthed prior to charging the system with any

refrigerant.

Label the system when charging is complete (if

not labeled already).

Extreme care mustl be taken not to overll

the refrigeration system. Prior to recharging

the system, it must be pressure tested with

OFN. The system must also be leak tested

on completion of charging but prior to

commissioning. A follow up leak test should be

carried out prior to leaving the site.

14. Decommissioning

Before carrying out this procedure, it is

essential that the technician is completely

familiar with the equipment and all its details.

It is considered as good practice that all

refrigerants are recovered safely. Prior to the

task being carried out, an oil and refrigerant

sample shall be taken, in the event that analysis

is required prior to re- use of reclaimed

refrigerant. It is essential that electrical power is

available before the task is commenced.

a) Become familiar with the equipment and its

operation.

b) Electrically isolate the system.

c) Before attempting this procedure please

ensure that: Mechanical handling equipment

is available, if required, for handling refrigerant

cylinders;

All personal protective equipment is available

and being used correctly; The recovery process

is supervised at all times by a competent

person;

Recovery equipment and cylinders conform to

the appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold

so that refrigerant can be removed from

various parts of the system.

f) Make sure that cylinder is situated on the

scales before recovery takes place.

g) Start the recovery machine and operate in

accordance with manufacturer's instructions.

h) Do not overll cylinders. (No more than 80 %

volume liquid charge).

i) Do not exceed the maximum working

pressure of the cylinder, even temporarily.

j) When the cylinders have been lled correctly

and the process completed, make sure that the

cylinders and the equipment are removed from

site promptly and all isolation valves on the

equipment are closed o.

k) Recovered refrigerant shall not be charged

into another refrigeration system unless it has

been cleaned and checked.

15. Labelling

Equipment must be labelled stating that it

has been de- commissioned and emptied of

|Warnings (for using R290/R32 refrigerant only)

EN 9

refrigerant. The label must be dated and signed.

Ensure that there are labels on the equipment

stating the equipment contains ammable

refrigerant.

16. Recovery

When removing refrigerant from a system,

either for servicing or decommissioning,

it is recommended good practice that all

refrigerants are removed in a safe manner.

When transferring refrigerant into cylinders,

ensure that only appropriate refrigerant

recovery cylinders are employed.

Ensure that the correct number of cylinders

for holding the total system charge is available.

All cylinders to be used are designated for

the recovered refrigerant and labelled for

that refrigerant (i.e. special cylinders for

the recovery of refrigerant). Cylinders shall

be complete with pressure relief valve and

associated shut- o valves in good working

order. Empty recovery cylinders are evacuated

and, if possible, cooled before recovery

occurs.

The recovery equipment shall be in good

working order with a set of instructions

concerning the equipment that is at hand and

shall be suitable for the recovery of ammable

refrigerants. In addition, a set of calibrated

weighing scales shall be available and in good

working order. Hoses shall be complete with

leak- free disconnect couplings and in good

condition. Before using the recovery machine,

check that it is in satisfactory working order,

has been properly maintained and that any

associated electrical components are sealed

to prevent ignition in the event of a refrigerant

release. Consult manufacturer if in doubt.

The recovered refrigerant shall be returned to

the refrigerant supplier in the correct recovery

cylinder, and the relevant Waste Transfer

Note arranged. Do not mix refrigerants in

recovery units and especially not in cylinders.

If compressors or compressor oils are to

be removed, ensure that they have been

evacuated to an acceptable level to make

certain that ammable refrigerant does not

remain within the lubricant. The evacuation

process shall be carried out prior to returning

the compressor to the suppliers. Only electric

heating to the compressor body shall be

employed to accelerate this process. When oil

is drained from a system, it shall be carried out

safely.

Important Note Regarding Fluorinated

Gasses

- Fluorinated greenhouse gases are contained

in rmly sealed equipment. For specic

information on the type, the amount and the

CO2 equivalent in tonnes of the uorinated

greenhouse gas (on some models), please refer

to the relevant label on the unit itself.

- Installation, service, maintenance and repair of

this unit must be performed only by a certied

technician.

- Unit un- installation and the recycling of, must

be performed by a certied technician.

|Warnings (for using R290/R32 refrigerant only)

10 EN

|Preparation

rear

MODEL A

MODEL B

power plug socket

power cord buckle

bottom tray

drain outlet

power cord outlet

drain outlet

(only for pump

heating mode)

upper air filter

(behind the grille)

upper air intake

air outlet

lower air filter

lower air intake

drain outlet

front

rear

control panel

handle

(both sides)

horizontal louver

blade

(swing automatically)

Caster

power plug socket

power cord buckle

vent control

bottom tray

drain outlet

power cord outlet

drain outlet

(only for pump

heating mode)

upper air filter

(behind the grille)

upper air intake

air outlet

lower air filter

lower air intake

drain outlet

Panel

SCALE 0.500

EN 11

|Installation|Installation

Choosing The Right Location

Tools Needed

Medium Philips screwdriver; - Tape measure or ruler; - Knife or scissors; - Saw (optional, to shorten

window adaptor for narrow windows).

Accessories

Check your window size and choose the t window slider.

50cm

19.7inch

Recommend Installation

NOTE: Items with * are optional. Slight variations in design may occur.

rear

MODEL A

MODEL B

power plug socket

power cord buckle

bottom tray

drain outlet

power cord outlet

drain outlet

(only for pump

heating mode)

upper air filter

(behind the grille)

upper air intake

air outlet

lower air filter

lower air intake

drain outlet

front

rear

control panel

handle

(both sides)

horizontal louver

blade

(swing automatically)

Caster

power plug socket

power cord buckle

vent control

bottom tray

drain outlet

power cord outlet

drain outlet

(only for pump

heating mode)

upper air filter

(behind the grille)

upper air intake

air outlet

lower air filter

lower air intake

drain outlet

Panel

SCALE 0.500

- The air conditioner should be placed on a rm foundation to

minimize noise and vibration. For safe and secure positioning,

place the unit on a smooth, level oor strong enough to

support the unit.

- The unit must be placed near a properly rated grounded

outlet.

- Allow at least 30cm of space from the wall for ecient air-

conditioning.

- Never obstruct the air inlet or outlet of the unit.

NOTE:

All the illustrations in this manual are for explanatory purposes

only. Your air conditioner may be slightly dierent. The actual

shape and size may vary.

The unit can be controlled by the unit control panel alone

or with the remote controller. This manual does not include

Remote Controller Operations, see the "Remote Controll

Illustration" packed with the unit for details.

There is the possibility of dierences between the user’s

manual and the illustrated photos of the remote control,

always refer to the manual for information.

12 EN

Europe

Part Description Quantity

Unit Adaptor

1 pc

Exhaust Hose

1 pc

*

Window Slider Adaptor

1 pc

*

Wall Exhaust Adaptor A

(only for wall installation)

1 pc

*

Wall Exhaust Adaptor B

(with cap) (only for wall

installation)

1 pc

*

Screw and anchor

(only for wall installation)

4 set

*

Window Slider A

1 pc

*

Window Slider B

1 pc

Power Cord Buckle

1 pc

Part Description Quantity

*

Bolt

1 pc

*

Security Bracket and Screw

1 set

Drain Hose

1 pc

Drain Hose Adaptor(only for

heat pump mode)

1 pc

*

Foam Seal A (Non- adhesive)

2 pc

*

Foam Seal B (Adhesive)

2 pc

*

Foam Seal C (Adhesive)

1 pc

ON/OFF

TEMP

SHORT

CUT

TIMER

ON

TIMER

OFF

MODE

FAN

SLEEP SWIN G LED

Remote Controller

and Battery

1set

NOTE: Items with * are optional. Slight variations in design may occur.

|Installation

Unit adaptor

Window slider

adaptor

Exhaust hose

Press into Press into

Exhaust hose

assembly

or

Make sure the hook of the adaptor is aligned

with the hole seat of the air outlet.

Hook Hole Seat

Lower groove

adaptor Make sure the adaptor is

inserted into the lower

groove of the air outlet.

Window slider A

MODEL A

MODEL B

Window slider B

Bolt

Window slider A Window slider B

Bolt

or

Window slider A Window slider B Window slider C

Bolts

Window slider A Window slider B Window slider C

Bolts

Window Installation Kit

Step One: Preparation of the Exhaust Pipe

Apply pressure to the exhaust pipe and the window

adaptor one side, and the unit adaptor on the other, attach

with the use of the elastic buckles located on the adaptors.

Step Two: Install the Exhaust hose assembly to the unit

Insert unit adaptor of the Exhaust hose assembly into

the lower groove of the air outlet of the unit while the

hook of the adaptor is aligned with the hole seat of the

air outlet and slide down the Exhaust hose assembly

along the arrow direction for installation.

Step Three: Preparing the Adjustable Window Slider

1. Depending on the window size, make necessary

adjustments on the window slider.

2. If the length of the window requires two window

sliders, use the bolt to fasten the window sliders once

they are adjusted to the proper length.

3. For some models, if the length of the window

requires three window sliders(optional), use two bolts

to fasten the window sliders once they are adjusted to

proper length.

EN 13

2 Screws

Security Bracket

Foam seal B

(Adhesive type-shorter)

Foam seal A

(Adhesive type)

Window slider A

Window slider B

(if required)

Foam seal C

(Non-adhesive type) Foam seal C

(Non-adhesive type)

2 Screws

Security

Bracket

or

MODEL A

MODEL B

Foam seal B

(Adhesive type-shorter)

Foam seal A

(Adhesive type)

Window slider A

Window slider B

(if required)

VENT CONTROL feature

CLOSE

OPEN

max 120cm or 47 inch

min 30cm or 12 inch

Expansion anchor

position

Adaptor cap

Wall Exhaust

Adaptor B

|Installation|Installation

Note: Once the Exhaust Hose assembly and

Adjustable Window Slider are prepared, choose

from one of the following installation methods.

Type 1: Hung Window or Sliding Window

Installation (optional)

Type 2: Wall Installation (optional)

1.Cut a 125mm (4.9inch) hole into the wall

for the Wall Exhaust Adaptor B. 2.Secure the

Wall Exhaust Adaptor B to the wall using the

four Anchors and Screws provided in the kit.

3.Connect the Exhaust Hose Assembly (with

Wall Exhaust Adaptor A) to the Wall Exhaust

Adaptor B.

1. Cut the foam seal (adhesive type) to the

proper length and attach it to the window

frame.

2. Attach the window slider kit to the window

opening.

4.If desired, install the security bracket with 2

screws as shown.

5.Insert the window slider adaptor into the hole

of the window slider.

3.Cut the non- adhesive foam seal C strip to match

the width of the window. Insert the seal between

the glass and the window frame to prevent air and

insects from getting into the room.

Note: Cover the hole

using the adaptor cap

when not in use.

Note: To ensure proper function, DO NOT

overextend or bend the hose. Make sure that

there is no obstacle around the air outlet of the

exhaust hose (in the range of 500mm) in order

to the exhaust system works properly. All the

illustrations in this manual are for explanation

purpose only.

Your air conditioner may be slightly dierent.

The actual shape shall prevail.

The Vent Control is located at the back of the

air conditioner. The OPEN position removes

stale air from the room and exhausts it to the

outside. Fresh air is drawn in through normal

passages in the home.

When not need to circulate the room air, set

Vent Control to CLOSE position. This function is

only applicable for MODEL B.

14 EN

HEAT mode light HIGH fan speed light

MED fan speed light

LOW fan speed light

AUTO fan speed light

SLEEP light

Degrees Celsius

Degrees Fahrenheit

LED display

I SENSE light

FILTER light

COOL mode light

FAN mode light

DRY mode light

AUTO mode light

|Operation

NOTE: ION, WIRELESS features are not available. ION is not applicable for R32/R290 units.

NOTE: The control panel may be look like the following:

EN 15

|Operation

Swing button

Used to initiate the Auto swing feature. When

the operation is ON, press the SWING button

can stop the louver at the desired angle.

Timer button

Used to initiate the AUTO ON start time and

AUTO OFF stop time program, in conjuction

with the + & - buttons. The timer on/o

indicator light illuminates under the timer

on/o settings.

Mode button

Choose the desired operating mode. By

pressing the MODE button each time an

operation is selected in the following order:

AUTO, COOL, DRY, FAN and HEAT (cooling

only models without). Indication led will

illuminate under the desired MODE setting.

Up (+) and Down (- ) buttons

Used to adjust (increasing/decreasing)

temperature settings in 1°C/1°F (or 2 °F)

increments in a range of 17°C/62°F to

30°C/86°F (or 88°F) or the TIMER setting in a

range of 0~24hrs.

NOTE: The remote control may display the

temperature in both Fahrenheit or Celsius.

To change press and hold the up/down

buttons for 3 sec.

Fan

Control the fan speed. Press to select the

fan speed in four steps- LOW, MED, HIGH

and AUTO. The fan speed indicator light

illuminates under dierent fan settings.

When select AUTO fan speed, all the fan

indicator lights turn dark. On some models,

when select AUTO fan speed, all the fan

indicator lights illumiante(optional).

Sleep(Eco) button

Used to initiate the SLEEP/ECO operation.

Power button

Power switch on/o.

LED display

Shows the set temperature in °C or °F

("°F" no display for some models) and the

Auto- timer settings. While on DRY and FAN

modes, it shows the room temperature.

Shows Error codes and protection code:

E1- Room temperature sensor error.

E2- Evaporator temperature sensor error.

E3- Condenser temperature sensor error

(on some models).

E4- Display panel communication error.

EC- Refrigerant leakage detection

malfunction (on some models).

P1- Bottom tray is full- Connect the drain

hose and drain the collected water away.If

protection repeats,call for service.

Note: When one of the above malfunctions

occurs, turn o the unit, and check for

any obstructions. Restart the unit, if the

malfunction is still present, turn o the

unit and unplug the power cord. Contact

the manufacturer or its service agents or a

similar qualied person for service.

Exhaust hose installation

The exhaust hose and its adaptor should

be installed or removed according to the

usage mode. Under COOL,HEAT(heat pump

type) or AUTO mode the exhaust hose must

be installed, under FAN,DEHUMIDIIFY or

HEAT(electrical heat type) the exhaust hose

should be removed.

16 EN

SCALE 0.500

Remove the air filter

Upper filter

(take out)

Remove the

screw,then

take the lower

filter out.

MODEL A MODEL B

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

SCALE 0.500

Remove the

upper drain plug

√

Continuous

drain hose

Remove the

upper drain plug

√

Continuous

drain hose

Uper air filter

(take out)

Lower air filter

(take out)

SCALE 0.500

X

drain hose

adaptor

Press the power

cord buckle into

the rear cover.

drain hose

adaptor

√

delivery lift <1.8m

Operation Instructions

COOL operation

- Press the "MODE" button until the "COOL" indicator

light comes on.

- Press the ADJUST buttons "+" or "- " to select your

desired room temperature. The temperature can be set

within a range of 17°C~30°C/62°F~86°F(or 88°F).

- Press the "FAN SPEED" button to choose the fan

speed.

HEAT operation(cooling only models without)

- Press the "MODE" button until the "HEAT" indicator

light comes on.

- Press the ADJUST buttons "+" or " - " to select your

desired room temperature. The temperature can be set

within a range of 17°C~30°C/62°F~86°F(or 88°F).

- Press the "FAN SPEED" button to choose the fan

speed. For some models, the fan speed can not be

adjusted under HEAT mode.

DRY operation

- Press the "MODE" button until the "DRY" indicator light

comes on.

- Under this mode, you cannot select a fan speed or

adjust the temperature. The fan motor operates at LOW

speed.

- Keep windows and doors closed for the best

dehumidifying eect.

- Do not put the duct to window.

AUTO operation

- When you set the air conditioner in AUTO mode, it

will automatically select cooling, heating(cooling only

models without), or fan only operation depending on

what temperature you have selected and the room

temperature.

- The air conditioner will control room temperature

automatically round the temperature point set by you.

- Under AUTO mode, you can not select the fan speed.

NOTE: Under AUTO mode, both the AUTO mode and

the actual operation mode indicator lights illuminate for

some models.

FAN operation

- Press the "MODE" button until the"FAN " indicator light

comes on.

- Press the "FAN SPEED" button to choose the fan

speed. The temperature can not be adjusted.

- Do not put the duct to window.

TIMER operation

- When the unit is on, press the Timer button will initiate

the Auto- o stop program, the TIMER OFF indicator

light illuminates. Press the UP or down button to select

the desired time. Press the TIMER button again within 5

seconds, the Auto- on start program is initiated.

And the TIMER ON indicator light illuminates. Press the

up or down button to select the desired Auto- on start

time.

When the unit is o, press the Timer button to initiate

the Auto- on start program, press it again within 5

seconds will initiate the Auto- o stop program.

- Press or hold the UP or DOWN button to change the

Auto time by 0.5 hour increments, up to 10 hours, then

at 1 hour increments up to 24 hours. The control will

count down the time remaining until start.

- The system will automatically revert back to display the

previous temperature setting if there is no operation in

a 5 seconds period.

- Turning the unit ON or OFF at any time or adjusting the

timer setting to 0.0 will cancel the Auto Start/Stop timer

program.

SLEEP (ECO) operation

- Press this button, the selected temperature will

increase (cooling) or decrease(heating) by 1°C/2°F(or

1°F) 30 minutes. The temperature will then increase

(cooling) or decrease (heating) by another 1°C/2°F(or

1°F) after an additional 30 minutes. This new

temperature will be maintained for the next 7 hours,

after the duration of the above time frame the unit will

return to the initial set temperature and ending the

SLEEP mode. NOTE: This feature is not available under

DRY or FAN mode.

Other features

AUTO- RESTART

In the event of power loss the unit will regain operation,

once power resumes, with the last settings.

AIR FLOW DIRECTION ADJUSTMENT

The louver can be adjusted automatically. Adjust the air

ow direction automatically:

- When the Power is ON, the louver opens fully.

- Press the SWING button on the panel or remote

controller to initiate the Auto swing feature. The louver

willl swing up and down automatically.

- Please do not adjust the louver manually.

|Operation

EN 17

SCALE 0.500

Remove the air filter

Upper filter

(take out)

Remove the

screw,then

take the lower

filter out.

MODEL A MODEL B

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

SCALE 0.500

Remove the

upper drain plug

√

Continuous

drain hose

Remove the

upper drain plug

√

Continuous

drain hose

Uper air filter

(take out)

Lower air filter

(take out)

SCALE 0.500

X

drain hose

adaptor

Press the power

cord buckle into

the rear cover.

drain hose

adaptor

√

delivery lift <1.8m

WAIT 3 MINUTES BEFORE RESUMING OPERATION

Once the unit has stopped its operation, it can not be re-

started within the rst 3 minutes, for the protection of the

device. Operation will automatically restart after 3 minutes.

I SENSE feature

The I SENSE function enables the remote control to

measure the temperature at its current location and

send this signal to the air conditioner every 3 minutes

interval. Measuring the ambient temperature from

the remote control (instead of using the indoor unit it-

self) will enable the portable air conditioner to opti-

mize the temperature around you and ensure maxi-

mum comfort.

NOTE:

For optimal results keep the remote pointing to

towards the unit and avoid any obstacles between the

unit and the remote that could possibly block the signal.

Water drainage

- When under dehumidifying mode, remove the drain

plug for the back of the unit and install the drain con-

nector (5/8 universal female mender) with a 3/4 hose

(may be purchased locally). For models without the

drain connector, please attach the drain hose to the

outlet, while placing the other side of the hose directly

over the drainage port of your basement oor.

During heating pump mode, remove the lower drain

plug from the back of the unit, install the drain connec-

tor(5/8" universal female mender) with 3/4" hose(local-

ly purchased). For the models without drain connector,

just attach the drain hose to the hole. Place the open

end of the Hose adaptor directly over the drain area in

your basement oor.

NOTE: Βe certain the hose is secure without any

leaking. Direct the hose toward the drain, in such a

manner that there are no breaks or bents securing

smooth water ow. (See Figs with R. Do never let it up.

(See Figs with S ). When the continuous drain hose is

not of use, ensure the drain plug is installed rmly to

prevent possible leakage.

- When the water level of the bottom tray reaches a

predetermined level, the unit beeps 8 times; the digi-

tal display area shows “PI”. At this time

the air conditioning/dehumidication

process will immediately stop. Howev-

er, the fan motor will continue to op-

erate (this is normal). Carefully move

the unit to a drain location, remove the

bottom drain plug and let the water

drain . Re- install the bottom drain plug and restart the

machine until the “PI” symbol disappears. If the error

persists, please call for service.

NOTE: Be sure to reinstall the bottom drain plug rm-

ly to prevent leakage before using the unit.

| Maintenance

WARNING:

- Be sure to unplug the unit before cleaning or

servicing

- DO NOT use ammable liquids or chemicals to

clean the unit.

- Do not wash the unit directly under a tap or us-

ing a hose as it may cause electrical shock.

- DO NOT operate this unit if the power cable is

damaged in any way. If the power cord is dam-

aged it must be replaced from the product man-

ufacturer and never repaired.

Clean the Air Filter

CAUTION

DO NOT operate the unit without lter because

dirt and lint will clog it and reduce performance.

|Operation

SCALE 0.500

Remove the air filter

Upper filter

(take out)

Remove the

screw,then

take the lower

filter out.

MODEL A MODEL B

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

SCALE 0.500

Remove the

upper drain plug

√

Continuous

drain hose

Remove the

upper drain plug

√

Continuous

drain hose

Uper air filter

(take out)

Lower air filter

(take out)

SCALE 0.500

X

drain hose

adaptor

Press the power

cord buckle into

the rear cover.

drain hose

adaptor

√

delivery lift <1.8m

SCALE 0.500

Remove the air filter

Upper filter

(take out)

Remove the

screw,then

take the lower

filter out.

MODEL A MODEL B

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

SCALE 0.500

Remove the

upper drain plug

√

Continuous

drain hose

Remove the

upper drain plug

√

Continuous

drain hose

Uper air filter

(take out)

Lower air filter

(take out)

SCALE 0.500

X

drain hose

adaptor

Press the power

cord buckle into

the rear cover.

drain hose

adaptor

√

delivery lift <1.8m

SCALE 0.500

Remove the air filter

Upper filter

(take out)

Remove the

screw,then

take the lower

filter out.

MODEL A MODEL B

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

√

drain hose

adaptor

Continuous

drain hose

Remove the

lower drain plug

SCALE 0.500

Remove the

upper drain plug

√

Continuous

drain hose

Remove the

upper drain plug

√

Continuous

drain hose

Uper air filter

(take out)

Lower air filter

(take out)

SCALE 0.500

X

drain hose

adaptor

Press the power

cord buckle into

the rear cover.

drain hose

adaptor

√

delivery lift <1.8m

18 EN

|Maintenance

| Troubleshooting

Maintenance Tips

- Clean the air lter every two weeks to prevent

inferior fan operation due to dust.

- The water collection tray must be drained

immediately in the event that the error P1 appears

on the digital control panel, and also before

storage to prevent the possibility of mold growth.

- In households with animals, you will have to

periodically wipe down the grill to prevent blocked

airow due to animal hair.

Clean the Unit

Use a damp lint- free cloth to clean the unit

enclosure. Dry with a clean and lint free cloth cloth.

Store the unit when not in use

- Drain the unit's water collection tray as per the

instructions in the following section.

- Operate the device on FAN mode for 12 hours in

a warm room to dry and prevent the possibility of

mold growth.

- Power o the unit and unplug.

- Clean the air lter as per the instructions in the

previous section. Reinstall the clean and dry lter

before storing.

- Batteries from the remote control should be

removed.

- Store in a cool, shady area. Any exposure directly

to sunlight or in extreme heat situations may

minimize the lifespan of this device.

NOTE: The main chassis and front of the unit

may be cleaned with by using a lint- free cloth and

soapy water (using a mild detergent) Dry with a

clean cloth. The use of harsh cleansers, or the

waxing and polishing of the unit is strongly not

advised. When cleaning the digital control panel

be certain the cloth is dry as any water around the

controls may cause damage to the unit.

Problem Possible Cause Troubleshooting

Unit does not turn on

when pressing ON/OFF

button

P1 Error Code The Water Collection Tray is full.

Turn o the unit, drain the water

from the Water Collection Tray and

restart the unit.

In COOL mode: room

temperature is lower than the

set temperature

Reset the temperature

Unit does not cool well

The air lter is blocked with dust

or debris Turn o the unit and clean the lter

according to instructions

Exhaust pipe is not connected

or is blocked Turn o the unit, disconnect the

hose, check for blockage and

reconnect the hose

The unit is low on refrigerant Call a service technician to inspect

the unit and top o refrigerant

Temperature setting is too high Lower the set temperature

The windows and doors in the

room are open Conrm all windows and exits are

shut

The room area is too large Double- check the cooling area

There are heat sources inside

the room Remove the heat sources if

possible

The unit is noisy and

vibrates too much

The ground is not level Place the unit on a at, level surface

The air lter is blocked with dust

or debris Turn o the unit and clean the lter

according to instructions

The unit makes a gurgling

sound This sound is caused by the ow

of refrigerant inside the unit This is normal

Please refer to the below prior to contacting customer support.

EN 19

|Design and Compliance Notes

Design Notice:

The design and the specications of this unit are subject to change at any given moment, without

prior notice, for the improvement of the product. Always consult with the after sales department or

the manufacturer for further details. Manuals are also subject to updates and you should always

check for the latest version by visiting the manufacturer’s website.

Energy Rating Information

The energy rating of this unit is based on typical installation with the use of the provided, and not

extended, exhaust pipe, without the use of the window slider adaptor or the wall exhaust adaptor A

(as shown in the Installation section of this manual).

Unit Temperature Range

Mode Temperature Range

Cool 17- 35°C (62- 95°F)

Dry 13- 35°C (55- 95°F)

Heat (pump heat mode) 5- 30°C (41- 86°F)

Heat (electrical heat mode) 30°C (86°F)

NOTE: To be in compliance EN 61000- 3- 11, the product M2GHP290-12 shall be connected only

to a supply of the system impedance: | Zsys|=0.348 ohms or less. Before connect the product

to public power network, please consult your local power supply authority to ensure the power

network meet above requirement.

20 EN

|Sociable Remark

When using this unit in the European countries, the following information must be followed:

DISPOSAL: Do not dispose this product as unsorted municipal waste. This appliance requires

special treatment for disposal.

It is prohibited to dispose of this appliance in domestic household waste.

There are several possibilities for disposal:

A. Your local municipality has established free collection systems for electronic waste.

B. Your local retailer will take back the old product with the purchase of a new product.

C. The manufacture will take back the old appliance for disposal.

D. The old products contain valuable resources and sometimes can be sold to scrap metal dealers.

Do not dispose this product randomly into the environment. The hazardous substances can leak

into the ground- water supply and nd their way into the food chain, endangering your health

and the environment.

All the pictures in the manual are for explanatory purposes only. The actual shape of the unit

you purchased may be slightly dierent, but the operations and functions are the same.

The company may not be held responsible for any misprinted information. The design and the

specications of the product for reasons, such as product improvement, are subject to change

without any prior notice.

Please consult with the manufacturer at +30 211 300 3300 or with the Sales agency for further

details. Any future updates to the manual will be uploaded to the service website, and it is

advised to always check for the latest version.

Scan here to download the latest version of this manual.

www.inventorairconditioner.com/media- library

La pagina sta caricando ...

Inventor M3GHP290-12 Portable Air Conditioning Systems Manuale utente

Inventor M3GHP290-12 Portable Air Conditioning Systems Manuale utente

in altre lingue

Altri documenti