Falmec FDLUM70I5SS-2L Manuale utente
- Categoria
- Cappe da cucina
- Tipo
- Manuale utente
Questo manuale è adatto anche per
INSTRUCTIONS BOOKLET
Design
Lumen 175 island
FDLUM70I5SS-2RRIGHT
FDLUM70I5SS-2LLEFT
INSTRUCTIONS BOOKLET EN
MODE D'EMPLOI FR
MANUAL DE INSTRUCCIONES ES
LIBRETTO ISTRUZIONI IT
2
2" - 50mm
23" 5/8 - 600mm
max
22" 1/2 - 572mm
12" 9/16 - 320mm 10" 3/16 - 258mm
23" 5/8 - 600mm
20" 1/16 - 510mm
4" 3/4 - 121mm
7/16”
11mm
5" 7/8 - 150mm
16’’ 1/2 - 420 mm
68’’ - 1750 mm
300 mm
20" 1/16 - 510mm
23" 5/8 - 600mm
11" 3/8 - 290mm
17’’ 12/16 - 450 mm 50” 3/4 - 1289mm
ø 5/16 - 8 mm
110 lb
50 kg
EN- tool required
FR- outil requis
ES- herramienta requerida
IT - Attrezzi necessari
LUMEN 175 ISLAND
FDLUM70I5SS2L 120VAC 60HZ 280W
3
ø 5/16 - 8 mm
110 lb
50 kg
EN- tool required
FR- outil requis
ES- herramienta requerida
IT - Attrezzi necessari
LUMEN 175 ISLAND
FDLUM70I5SS2R 120VAC 60HZ 280W
23" 5/8 - 600mm
max
22" 1/2 - 572mm
12" 9/16 - 320mm
2" - 50mm
10" 3/16 - 258mm
23" 5/8 - 600mm
20" 1/16 - 510mm
23" 5/8 - 600mm
68" - 1750mm
20" 1/16 - 510mm
7/16”
11mm 11" 3/8
290mm
16’’ 1/2 - 420 mm
11" 13/16 - 300mm
50" 3/4 - 1289mm 17" 12/16 - 450mm
5" 7/8 - 150mm
4
2" 1/4
57 mm
2"
50 mm
10" 7/16
265 mm
4" 5/16
110 mm
12" 6/16 - 316 mm
11" 3/16 - 285 mm
7" 7/8 - 200 mm
10" - 254 mm
Ø 1/4 - 6 mm
ø 5" 7/8
150 mm
ø 6" 5/16
160 mm
EN - Side outlet which can only be used with
false ceiling.
FR - Sortie latérale utilisable uniquement
avec faux-plafond.
ES - Salida lateral utilizable solo con falso
techo.
IT - Uscita laterale utilizzabile solo con con-
trosotto.
EN- cable length 5,0ft (1,5m)
FR- longueur de câble 5,0ft (1,5m)
ES- longueur de câble 5,0ft (1,5m)
IT- lunghezza cavo 5,0ft (1,5m)
1
H1
1" - 50 mm
CEILING
1
A
H
EN - Ceiling installation (1),
false ceiling installation (2). FR - Installation au plafond (1),
installation sur faux-plafond
(2).
ES - Instalación en el techo (1),
instalación en el contratecho
(2).
IT - Installazione a so tto (1),
installazione a controso tto
(2).
A = 24" - 35"
610 mm - 890 mm
(RECOMMENDED FOR
OPTIMAL PERFORMANCE)
EN - Installation measurements
Recommended mounting height from cooking surface to hood bottom
is indicated by "A" in the drawing below. It is recommended to install
the hood in this range to optimize performance. It is recommended to
not exceed 35” (890mm) for dimension “A” as hoods mounted above this
may be diffi cult to reach for average height users and performance and
effi ciency will degrade. Hoods mounted below the lower measurement
in the “A” recommendation could result in damage due to heat and pres-
ent a fi re hazard and would avoid any warranty claims attributable to
the lower mounting position. If available, also refer to the cooking appli-
ance manufacturer’s height clearance recommendations and adhere to
national and local building and fi re codes which supersede any recom-
mendations stipulated herein.
FR - Mesures pour installation
La hauteur de montage recommandée entre la surface de cuisson et la par-
tie inférieure de la hotte est indiquée par le « A » dans le dessin ci-dessous.
Il est recommandé d’installer la hotte dans cette plage pour optimiser sa
performance. Il est recommandé de ne pas dépasser les 890 mm (35 po)
pour la dimension « A », car les hottes montées à une distance au-dessus
peuvent être diffi ciles à atteindre pour les utilisateurs de hauteur moyenne,
et cela diminuera leur performance et effi cacité. Les hottes montées en-
dessous de la mesure inférieure de la recommandation « A » pourraient
s’abîmer par la chaleur et présenter un risque d’incendie, ce qui annulerait
toute réclamation de garantie attribuable à la position de montage infé-
rieure. Le cas échéant, reportez-vous également aux recommandations
du fabricant de l’appareil de cuisson en ce qui a trait au dégagement en
hauteur et respectez les codes du bâtiment et de prévention des incendies
nationaux et locaux qui remplacent toutes les recommandations stipulées
dans le présent document.
ES - Medidas instalación
La altura de montaje recomendada desde la superfi cie de cocción hasta
el fondo de la campana se indica con una "A" en el dibujo siguiente.
Se recomienda instalar la campana en este rango para optimizar el
rendimiento. Se recomienda no exceder 35" (890mm) para la dimensión
"A" ya que las campanas montadas por encima de ésta pueden ser
difíciles de alcanzar para los usuarios de altura media y el rendimiento
y la efi ciencia se degradarán. Las campanas montadas por debajo de la
medida inferior de la recomendación "A" podrían resultar dañadas por el
calor y presentar un riesgo de incendio, y evitarían cualquier reclamación
de garantía atribuible a la posición de montaje inferior. Si está disponible,
consulte también las recomendaciones de altura del fabricante del equipo
de cocina y respete los códigos de construcción y contra incendios,
nacionales y locales, que sustituyen cualquier recomendación estipulada
en el presente documento.
IT - Misure per l'installazione
L’altezza di montaggio consigliata tra il piano cottura e la parte inferiore
della cappa è indicata dalla lettera “A” nella fi gura sottostante. Per ottene-
re prestazioni ottimali, si raccomanda di installare la cappa entro i limiti,
massimo e minimo, mostrati nella fi gura. È consigliabile che le dimensioni
di “A” non superino i 35” (890mm) in quanto le cappe montate più in alto
potrebbero presentare un livello ridotto di rendimento ed effi cienza, oltre
a risultare diffi cili da raggiungere da parte degli utenti di altezza media. Al
contrario, le cappe montate al di sotto dell’altezza minima consigliata in
“A” potrebbero danneggiarsi per il calore proveniente dal piano cottura e
presentare un rischio di incendio. Si ricorda che la garanzia non risponde
di eventuali danni derivanti da un montaggio in posizione troppo bassa.
Se disponibile, fare riferimento anche all’altezza libera raccomandata dal
produttore del piano cottura. In ogni caso, è sempre necessario rispettare
le norme edilizie e antincendio in vigore, a livello sia nazionale sia locale, le
quali prevalgono su qualsiasi raccomandazione contenuta nel presente.
2
H1
H
CEILING
FALSE CEILING
2" - 50 mm
1
A
A = 24" - 35"
610 mm - 890 mm
(RECOMMENDED FOR
OPTIMAL PERFORMANCE)
6
V2 (x8)
V1
T
T1
ø5/16
8mm
V1 (x4)
4
3
2
1
ø5/16
8mm
ø5/16
8mm
EN - Installation on ceiling with/without false ceiling (4).
FR - Installation au plafond avec/sans faux-plafond (4).
ES - Instalación en techo con/sin cielo raso (4).
IT installazione su sotto con/senza controsotto (4)
4
3
V2 (x8)
T
T1
1
H1
EN - Preliminary operations: separate upper trellis from
lower trellis (3).
FR - Opérations préliminaires : séparer le rail supérieur
du rail inférieur (3).
ES - Operaciones preliminares: separar la estructura superior
de la estructura inferior (3).
IT - Operazioni preliminari: separare traliccio superiore
da traliccio inferiore (3).
7
EN - Secure tie rod supports (5).
FR - Fixation des supports pour tirants (5).
ES - Fijación de los soportes para tirantes (5).
IT Fissaggio supporti per tiranti (5).
7” 7/8 - 200mm
10”
255mm
7/16”
11mm
10”
255mm
45” 1/8 - 1146mm
11” 3/16
285mm
7/16”
11mm
10”
255mm
10”
255mm
45” 1/8 -1146mm
11” 3/16
285mm
7” 7/8
200mm
Ø6
1 2
LEFT version
RIGHT version
5
8
6
7 8
4
2
M
ERM
ERM
3
5
6
1
5" 7/8
150mm
ø
5" 7/8
150mm
EN - Check valve installation (6). Assemble exhaust pipe (7).
Assembly chimney and extension (8).
FR - Installation du clapet anti-retour (6). Montage du tuyau d'as-
piration (7). Assemblage de la cheminée et de l'extension (8).
ES - Instalación de la válvula antirretorno (6). Montaje del tubo
de aspiración (7). Montaje de chimenea y extensión (8).
IT - Installazione valvola di non ritorno (6). Montaggio tubo aspi-
razione (7). Assemblaggio camino ed estensione (8).
9
EN - Mount chimney on ceiling (9).
FR - Montage de la cheminée au plafond (9).
ES - Montaje de chimenea en techo (9).
IT - Montaggio camino a sotto (9).
1
CEILING
2
V3 (x4)
FALSE CEILING
V4 (x8)
SP
1
2
3V3 (x4)
EN - Mount chimney on false ceiling (10).
FR - Montage de la cheminée au faux-plafond (10).
ES - Montaje de chimenea en falso techo (10).
IT - Montaggio camino a controsotto (10).
9
10
10
12
11
EN - Remove panel (11) and metallic lters (12).
FR -
Retirer le panneau (11) et les ltres métalliques (12).
ES - Quitar el panel (11) y los ltros metálicos (12).
IT - Togliere pannello (11) e ltri metallici (12).
3
2
1
12
3
4
11
12
34 5
YES
NO
H2
V5 (x4)
1
V5 (x4)V5 (x4)
2B
2A
14
13EN - Mount motor chamber (13) and tie rods (14).
FR -
Montage de la chambre du moteur (13) et des tirants (14).
ES - Montaje de la cámara del motor (13) y tirantes (14).
IT - Montaggio camera motore (13) e tiranti (14).
12
3
5
4
V3 (x4)
1
V3 (x4) 2
15
EN -
Electrical connections (15) and chimney installation (16).
FR -
Raccord électrique (15) et xation de la cheminée (16).
ES - Conexión eléctrica (15) y jación de la chimenea (16).
IT - Collegamento elettrico (15) e ssaggio camino (16).
16
EN - Mandatory safety screws
FR - Vis de sécurité obligatoires
ES - Tornillos de seguridad obligatorios
IT - Viti di sicurezza obbligatorie
13
2
1
1
18
17
2
3
1
EN - Installing the carbon-zeolite lter (optional)
FR - Installation du iltre charbon-zeolite (en option)
ES - Instalacion de iltro de carbon-zeolita (opcional)
IT - Installazione ltro carbone-zeolite (opzionale)
OPTIONAL
KACL.961
14
SAFETY INSTRUCTIONS
AND WARNINGS
READ AND SAVE THESE INSTRUCTIONS
Installation operations are to be carried
out by skilled and qualied installers in ac-
cordance with the instructions in this booklet and
in compliance with the regulations in force.
DO NOT use the hood if the power supply cable
or other components are damaged: disconnect
the hood from the electrical power supply and con-
tact the Dealer or an authorised Servicing Dealer for
repairs.
Do not modify the electrical, mechanical or
functional structure of the equipment.
Do not personally try to carry out repairs or
replacements. Interventions carried out by
incompetent and unauthorised persons can
cause serious damage to the unit or physical and
personal harm, not covered by the Manufacturer's
warranty.
WARNING: TO REDUCE THE RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by
the manufacturer. If you have questions, contact
the manufacturer.
b) Before servicing or cleaning unit, switch pow-
er o at service panel and lock the service dis-
connecting means to prevent power from being
switched on accidentally.
When the service disconnecting means cannot
be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do
Not Use To Exhaust Hazardous Or Explosive Ma-
terials And Vapors.
WARNINGS FOR THE INSTALLER
TECHNICAL SAFETY
Before installing the hood, check the integ-
rity and function of each part. Should
anomalies be noted, do not proceed with installa-
tion and contact the Dealer.
Do NOT install the hood if an aesthetic (or cos-
metic) defect has been detected. Put it back into
its original package and contact the dealer.
No claim can be made for aesthetic (or cosmetic)
defects once it has been installed.
During installation, always use personal protective
equipment (e.g.: Safety shoes) and adopt prudent
and proper conduct.
The installation kit (screws and plugs) supplied with
the hood is only to be used on masonry walls: in case
of installation on walls of a different material, assess
other installation options keeping in mind the type of
wall surface and the weight of the hood (indicated on
spec sheets at the beginning of this manual).
Keep in mind that installations with different types of
fastening systems from those supplied, or which are
not compliant, can cause electrical and mechanical
seal danger.
Do not install the hood outdoors and do not expose
it to atmospheric elements (rain, wind, etc.).
All set screws must be checked, and retightened
where necessary, before installation.
CAUTION: To Reduce The Risk Of Fire And Electric
Shock, Install This Rangehood Only With Remote
Blower Or Integral Blowers Manufactured by FAL-
MEC S.p.A. Models “Remote in-roof Blower”.
ELECTRICAL SAFETY
The installation has to be in accordance with the
National Electrical Code, ANSI/NFPA 70 and local
codes. Making sure the power is o before at-
tempting installation.
The electrical system to which the hood is
to be connected must be in accordance
with local standards and supplied with earthed
connection in compliance with safety regulations
in the country of use. It must also comply with lo-
cal standards regarding radio antistatic proper-
ties.
WARNING: GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for the electric current. This appliance is equipped
with a cord having a grounding wire with a
grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk
of electric shock. Consult a qualied electrician if
the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not use an extension cord. If the power supply
cord is too short, have a qualied electrician in-
stall an outlet near the appliance.
15
ENGLISH
Before installing the hood, check that the electrical
mains power supply corresponds with what is report-
ed on the identification plate located inside the hood.
The socket used to connect the installed equipment
to the electrical power supply must be within reach:
otherwise, install a mains switch to disconnect the
hood when required.
Any changes to the electrical system must be carried
out by a qualified electrician.
The maximum length of the flue fastening screws
(supplied by the manufacturer) must be 1/2" (13 mm).
Use of non-compliant screws with these instructions
can lead to danger of an electrical nature.
Do not try to solve the problem yourself in the event
of equipment malfunction, but contact the Dealer or
an authorised Servicing Department for repairs.
When installing the hood, disconnect the
equipment by removing the plug or switch-
ing o the main switch.
WARNING: To Reduce The Risk Of Fire Or Electric
Shock, Do Not Use This Fan With Any Solid-State
Speed Control Device
WARNING: NOT SUITABLE FOR USE WITH SOL-
ID-STATE SPEED CONTROLS
FUMES DISCHARGE SAFETY
Do no connect the equipment to discharge
pipes of fumes produced from combustion
(for example boilers, replaces, etc.).
Before installing the hood, ensure that all standards in
force regarding discharge of air out of the room have
been complied with.
To reduce risk of re and to properly exhaust air,
be sure to duct air outside – Do not vent exhaust
air into spaces within walls or ceilings or into at-
tics, crawl spaces, or garages.
WARNING: TO REDUCE THE RISK OF FIRE, USE
ONLY METAL DUCTWORK.
USER WARNINGS
These warnings have been drawn up for
your personal safety and those of others.
You are therefore kindly asked to read the book-
let carefully in its entirety before using the or
cleaning the equipment.
The Manufacturer declines all responsibility for
any damage caused directly, or indirectly, to per-
sons, things and pets as a consequence of failing
to comply with the safety warnings indicated in
this booklet. It is imperative that this instructions
booklet is kept together with the equipment for
any future consultation.
If the equipment is sold or transferred to another per-
son, make sure that the booklet is also supplied so
that the new user can be made aware of the hood's
operation and relative warnings.
After the stainless steel hood has been installed, it
will need to be cleaned to remove any residues re-
maining from the protective coating as well as any
grease and oil stains which, if not removed, can cause
irreversible damage to the hood surface. To properly
clean the unit, the manufacturer recommends using
the supplied moist wipes, which are also available
sold separately.
Insist on original spare parts.
State of California Proposition 65 Warning
(US only)
WARNING
This product contains chemicals known to the State
of California to cause cancer and birth defects or oth-
er reproductive harm.
For more information go to www.P65Warnings.ca.gov
INTENDED USE
The equipment is solely intended to be used to
extract fumes generated from cooking food in
non-professional domestic kitchens: any other
use is improper. Improper use can cause damage
to persons, things, pets and exempts the Manu-
facturer from any liability.
The equipment can be used by children over the age
of 8 and by persons with reduced physical, sensory
and mental abilities, or with no experience or knowl-
edge, as long as they do so under supervision or after
having received relative instructions regarding safe
use of the equipment and understanding of the dan-
gers connected to it.
Children are not to play with the equipment. Clean-
ing and maintenance by the user must not be carried
out by children without supervision.
USE AND CLEANING WARNINGS
WARNING: TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
a) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low
or medium settings.
b) Always turn hood ON when cooking at high
16
heat or when ambeing food (i.e. Crepes Suzette,
Cherries Jubilee, Peppercorn Beef Flambe').
c) Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or lter.
d) Use proper pan size. Always use cookware ap-
propriate for the size of the surface element.
WARNING:TO REDUCE THE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWINGa:
a) SMOTHER FLAMES with a close-tting lid, cook-
ie sheet, or metal tray, then turn o the burner.
BE CAREFUL TO PREVENT BURNS. If the ames
do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN – You may be
burned.
c) DO NOT USE WATER, including wet dishcloths
or towels – a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a Class ABC extinguisher,
and you already know how to operate it.
2) The re is small and contained in the area
where it started.
3) The re department is being called.
4) You can ght the re with your back to an exit.
a Based on "Kitchen Firesafety Tips" published by
NFPA.
Before cleaning or carrying out mainte-
nance operations, disconnect the equip-
ment by removing the plug or switching o the
main switch.
Do not use the hood with wet hands or bare feet.
Always check that all electrical parts (lights, extractor
fan) are off when the equipment is not being used.
The maximum overall weight of any objects placed or
hung (if applicable) on the hood must not exceed 3lb
5oz (1.5 Kg).
Always supervise the cooking process during the use of
deep-fryers: Overheated oil can catch fire.
Do not leave open, unattended flames under the hood.
Do not prepare food over an open flame under the
hood.
Never use the hood without the metal anti-grease
filters: in this case, grease and dirt will deposit in the
equipment and compromise its operation.
Accessible parts of the hood can be hot when used at
the same time as the cooking appliances.
Do not carry out any cleaning operations when parts of
the hood are still hot.
There can be a risk of fire if cleaning is not carried out
according to the instructions and products indicated in
this booklet.
Disconnect the main switch when the equipment is
not used for long periods of time.
If other appliances that use gas or other fu-
els are being used at the same time (boiler,
stove, replaces, etc.), make sure the room where
the fumes are discharged is well-ventilated, in
compliance with the local regulations.
INSTALLATION
Intended only for qualied personnel
Before installing the hood, carefully read the section 'SAFETY
INSTRUCTIONS AND WARNINGS'.
TECHNICAL FEATURES
The technical specifications are exhibited on the labels located inside the hood.
POSITIONING
The minimum distance between the highest part of the cooking equip-
ment and the lowest part of the hood is indicated in the installation in-
structions.
Should the instructions for the gas cooker specify a greater distance, this must
be taken into consideration.
Do not install the hood outdoors and do not expose it to outdoor environment
(rain, wind, etc.).
ELECTRICAL CONNECTION
(Intended only for qualied personnel)
Disconnect the equipment from electrical mains power supply be-
fore carrying out any operations on the hood.
Ensure that the wires inside the hood are not disconnected or cut:
in the event of damage, contact your nearest Servicing Department.
Refer to qualied personnel for electrical connections.
Connection must be carried out in compliance with the provisions of law
in force.
Before connecting the hood to the electrical mains power supply, check that:
• voltage supply corresponds with what is reported on the data plate located
inside the hood;
• the electrical system is compliant and can withstand the load (see the techni-
cal specifications located inside the hood);
• the power supply plug and cable do not come into contact with tempera-
tures exceeding 158°F (70 °C);
• the power supply system is effectively and properly connected to earth in
compliance with regulations in force;
• the socket used to connect the hood is within reach.
In case of:
• devices fitted with cables without a plug: the type of plug to use is a ''stand-
ardised'' one. The wires must be connected as follows: yellow-green for
grounding, blue for neutral and brown for the live. The plug must be con-
nected to an adequate safety socket.
• fixed equipment not provided with a power supply cable and plug, or any
other device that ensures disconnection from the electrical mains, with an
opening gap of the contacts that enables total disconnection in overvoltage
category III conditions.
Said disconnection devices must be provided in the mains power supply in
compliance with installation regulations.
The cable must not be cut off by the switch.
The Manufacturer declines all responsibility for failure to comply with the safety
regulations.
17
ENGLISH
FUMES DISCHARGE
EXTERNAL EXHAUST HOOD SUCTION
In this version the fumes and vapours are discharged outside
through the exhaust pipe.
To this end, the hood outlet fitting must be connected via a
pipe, to an external output.
The outlet pipe must have:
• a diameter not less than that of the hood fitting.
• a slight slope downwards (drop) in the horizontal sections to prevent conden-
sation from flowing back into the motor.
• the minimum required number of bends.
• the minimum required length to avoid vibrations and reduce the suction per-
formance of the hood.
You are required to insulate the pipes if it passes through cold environments.
In the presence of motors with 500 CFM or higher, a check valve is present to
prevent external air flowing back.
HOOD WITH INTERNAL RECIRCULATION FILTERING
In this model, the air passes through the charcoal filters to be
purified and recycled in the environment.
Ensure that the active carbon filters are assembled into the
hood, if not, install them as indicated in the assembly instruc-
tions.
In this version the check valve must not be assembled: remove it if it is
on the air outlet fitting of the motor.
ASSEMBLY INSTRUCTIONS
Intended only for qualied personnel
The hood can be installed in various congurations.
The generic assembly steps apply to all installations; for each case,
follow the specic steps provided for the required installation.
OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at least one minute before starting to cook to direct fumes
and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours
and odours. By means of the Timer function, it is possible to set auto switch-off
function which will allow the hood to turn off automatically after 15 minutes of
operation.
WHICH SPEED IS TO BE SELECTED?
1st speed: maintains the circulation of clean air with low electricity consumption.
2nd speed: normal conditions of use.
3rd speed: presence of strong odours and vapours.
4th speed: rapid disposal of odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The metal filters must be cleaned every 30 hours of operation.
For further details refer to the “MAINTENANCE” section.
ELECTRONIC PUSHBUTTON PANEL
Motor ON/OFF
Increase speed from 1 to 4
Speed 4 is only active for a few
minutes, then speed 3 activates.
The speeds are indicated by the
LEDs on the keys:
Speed 1
Speed 2
Speed 3
Speed 4
("+" LED flashing)
Reduce speed from 4 to 1
Light on/o
TIMER (red LED flashing)
Auto switch-off after 15 min.
The function deactivates (red LED off) if:
- The TIMER key ( ) is pressed again.
- The ON/OFF key ( ) is pressed.
FILTER ALARM (red LED steady on with ( ) off)
Anti-grease filter maintenance after approximately 30 hours of op-
eration.
Press ( ) the meter for 3 seconds to reset.
If the pushbutton panel is completely inactive, before contacting
the Technical assistance service, disconnect power temporarily to
the appliance (about 5“), possibly by acting on the main switch, to
restore normal operation.
If this measure has no eect, contact the Technical assistance service.
MAINTENANCE
Before cleaning or carrying out maintenance operations, discon-
nect the equipment by removing the plug or switching o the
main switch.
Do not use detergents containing abrasive, acidic or corrosive substances
or abrasive cloths.
Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the metal anti-grease lters : frequent clean-
ing of the filters and their supports ensures that no flammable grease is accu-
mulated.
CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood at least once every
15 days to prevent oily substances and grease from sticking to them. To clean
the brushed stainless steel hood, the Manufacturer recommends using "Magic
Steel" wipes.
Alternatively and for all the other types of surfaces, it can be cleaned using a
damp cloth, slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths.
Do not use too much moisture or water around the push button
control panel and lighting devices in order to prevent humidity
from reaching electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or non-abra-
sive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these in-
structions.
18
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor inside
the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal filters (at least once a month) leav-
ing them to soak in boiling water and cleaning solution for 1 hour, taking care
not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling
them.
Washing in a dishwasher is permitted, however, it may cause the filter material to
darken: to reduce the possibility of this problem from happening, use low-tem-
perature washes (131°F / 55°C max.).
To extract and insert the metal anti-grease filters see the assembly instructions.
CARBON AND ZEOLITE FILTERS (OPTIONAL) KACL.961
In normal use conditions, we recommend regenerating the zeolite-carbon filter
every 9 months and replacing it after 18 months. Simply place it in a domestic
oven at a temperature of 200°C for approximately 1 hour to regenerate it.
Wait until the filter cools before reassembling it.
LIGHTING
The range hood is equipped with high efficiency, low consumption LED spot-
lights with an extremely long life-span under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure.
12V
3
1
2
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance means
that the product is WEEE, i.e. “Waste electrical and electronic equip-
ment'', accordingly it must not be disposed of with regular unsort-
ed waste (i.e. with ''mixed household waste''), but it must be disposed of sepa-
rately so that it can undergo specific processing for its re-use, or a specific
treatment, to remove and safely dispose of any substances that may be harmful
to the environment and remove the raw materials that can be recycled. Proper
disposal of these products contributes to saving valuable resources and avoid
potential negative effects on personal health and the environment, which may
be caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further information
regarding the designated waste collection points nearest to you. Penalties for
improper disposal of such waste can be applied in compliance with national
regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented differently in each country, accord-
ingly, if you wish to dispose of this appliance we suggest contacting your local
authorities or dealer to find out what the correct method of disposal is.
INFORMATION ON DISPOSAL IN NONEUROPEAN UNION COUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if
you wish to dispose of this appliance in other countries, we suggest contacting
your local authorities or dealer to find out what the correct method of disposal is.
WARNING!
The Manufacturer reserves the right to make changes to the equipment at any
time and without prior notice. Printing, translation and reproduction, even par-
tial, of this manual are bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifications in this manual
are for information purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any tran-
scription or translation errors.
19
FRANÇAIS
CONSIGNES DE SÉCURITÉ
ET MISES EN GARDE
LIRE ET CONSERVER CES INSTRUCTIONS
Le travail d'installation doit être eectué
par des installateurs compétents et quali-
és, conformément aux indications du présent
manuel et en respectant les normes en vigueur.
Si le câble d'alimentation ou d’autres composants
sont endommagés, la hotte NE doit PAS être utili-
sée: débrancher la hotte de l'alimentation électrique
et contacter le revendeur ou un Centre d’Assistance
technique agréé pour la réparation.
Ne pas modier la structure électrique, méca-
nique et fonctionnelle de l'appareil.
Ne pas tenter d'eectuer soi-même des réparat-
ions ou des remplacements: les interventions ef-
fectuées par des personnes non compétentes et
non qualiées peuvent provoquer des domma-
ges, éventuellement très graves, à des choses et/
ou à des personnes, non couverts par la garantie
du Fabricant.
AVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE
D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLES-
SURE, RESPECTER CE QUI SUIT :
a) N’utiliser cet appareil que de la manière pré-
vue par le fabricant. Si vous avez des questions,
contactez le fabricant.
b) Avant de procéder à l’entretien ou au net-
toyage de l’appareil, couper l’alimentation sur le
panneau de service et verrouiller le système de
déconnexion du service pour éviter toute mise
sous tension accidentelle.
Lorsqu’il n’est pas possible de verrouiller le sys-
tème de déconnexion du service, xer solide-
ment un un dispositif d’avertissement bien vi-
sible, comme par exemple une étiquette, sur le
panneau de service.
ATTENTION : Pour un usage général de ventilation
uniquement. Ne pas utiliser pour évacuer des ma-
tières et des vapeurs dangereuses ou explosives.
MISES EN GARDE POUR L’INSTALLATEUR
SÉCURITÉ TECHNIQUE
Avant d'installer la hotte, contrôler l'inté-
grité et la fonctionnalité de chaque partie:
en cas de constatation d'anomalies, ne pas procé-
der à l'installation et contacter le Revendeur.
En cas de constatation d'un défaut esthétique, la
hotte NE doit PAS être installée; la remettre dans
son emballage d’origine et contacter le Reven-
deur.
Après son installation, aucune réclamation ne sera
acceptée pour des défauts esthétiques.
Pendant l'installation, toujours utiliser des équipe-
ments de protection individuelle (ex. : des chaussures
de sécurité) et adopter un comportement prudent et
correct.
Le kit de fixation (vis et chevilles) fourni avec la hotte
est utilisable uniquement sur des murs en maçonne-
rie : s'il faut installer la hotte sur des murs de maté-
riau différent, évaluer d’autres systèmes de fixation en
tenant compte de la résistance du mur et du poids de
la hotte (indiqué à la page 2).
Tenir compte du fait que l'installation avec des sys-
tèmes de fixation différents de ceux fournis ou non
conformes peut comporter des risques de nature
électrique et de tenue mécanique.
Ne pas installer la hotte à l’extérieur et ne pas l’expo-
ser à des agents atmosphériques (pluie, vent, etc.).
Toutes les vis de réglage doivent être vérifiées, et res-
serrées si nécessaire, avant l’installation.
ATTENTION : An de réduire les risques d’incen-
die et de chocs électriques, installer cette hotte
de cuisine uniquement avec un ventilateur à di-
stance ou des ventilateurs intégrés fabriqués par
FALMEC S.p.A. Modèles « Ventilateur de toit à di-
stance ».
SÉCURITÉ ÉLECTRIQUE
L’installation doit être conforme au Code national
de l’électricité, ANSI/NFPA 70 et aux codes locaux.
Assurez-vous que l’alimentation soit coupée
avant de procéder à l’installation.
Le circuit électrique, auquel est reliée la
hotte, doit être aux normes et muni d’un
raccordement à la terre, conformément aux
normes de sécurité du pays d’utilisation; il doit
en outre être conforme aux normes européennes
sur l'antiparasite radio.
AVERTISSEMENT : INSTRUCTIONS DE MISE À LA
TERRE
Cet appareil doit être mis à la terre. Dans le cas
d’un court-circuit électrique, la mise à la terre
réduit le risque de choc électrique en fournissant
un l d’évacuation pour le courant électrique.
Cet appareil est équipé d’un cordon comportant
un l de mise à la terre avec une che de mise à
la terre.
La che doit être branchée dans une prise de cou-
rant correctement installée et mise à la terre.
AVERTISSEMENT : Une mise à la terre incorrecte
peut entraîner un risque de choc électrique.
Consulter un électricien qualié si les instructions
20
de mise à la terre ne sont pas entièrement com-
prises, ou en cas de doute sur la mise à la terre
correcte de l’appareil.
Ne pas utiliser pas de rallonge. Si le cordon d’ali-
mentation est trop court, demander à un élec-
tricien qualié d’installer une prise de courant à
proximité de l’appareil.
Avant d'installer la hotte, s'assurer que la tension du
secteur correspond à celle reportée sur la plaque qui
se trouve à l'intérieur de la hotte.
La prise utilisée pour le branchement électrique doit
être facilement accessible avec l'appareil installé : si
cela n'était pas possible, prévoir un interrupteur gé-
néral pour déconnecter la hotte en cas de besoin.
Toute modification de l'installation électrique devra
être uniquement effectuée par un électricien qualifié.
La longueur maximum de la vis de fixation de la
cheminée (fournie par le fabricant) est de 13 mm.
L'utilisation de vis non conformes avec les présentes
instructions peut comporter des risques de nature
électrique.
En cas de dysfonctionnements de l'appareil, ne pas
tenter de résoudre personnellement le problème,
mais contacter le revendeur ou un Centre d'Assis-
tance agréé pour la réparation.
Pendant l'installation de la hotte, débran-
cher l'appareil en retirant la prise ou en
agissant sur l'interrupteur général.
AVERTISSEMENT : An de réduire le risque d’in-
cendie ou de choc électrique, ne pas utiliser ce
ventilateur avec tout régulateur de vitesse à se-
mi-conducteur
AVERTISSEMENT: NE CONVIENT PAS À DES RÉGU-
LATEURS DE VITESSE À SEMICONDUCTEURS.
SÉCURITÉ ÉVACUATION DES FUMÉES
Ne pas raccorder l'appareil aux conduits
d'évacuation des fumées produites par la
combustion (par ex. chaudières, cheminées, etc.)
Avant l'installation de la hotte, s'assurer que toutes
les normes en vigueur sur l’évacuation de l'air à l'exté-
rieur de la pièce sont respectées.
An de réduire le risque d’incendie et d’évacuer
correctement l’air, assurez-vous de faire circuler
l’air à l’extérieur – Ne pas faire entrer l’air évacué
dans des espaces clos entre des murs, des pla-
fonds ou dans des greniers, des vides sanitaires
ou des garages.
AVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE
D’INCENDIE, UTILISER UNIQUEMENT DES
CONDUITS MÉTALLIQUES.
MISES EN GARDE POUR L'UTILISATEUR
Ces mises en garde ont été rédigées pour
votre sécurité et pour celle d'autrui, nous
vous prions donc de lire attentivement toutes les
parties de ce manuel avant d'utiliser l'appareil ou
de le nettoyer. Le fabricant décline toute respon-
sabilité pour d’éventuels dommages, directs ou
indirects, pouvant être causés aux personnes,
aux choses et aux animaux domestiques, suite au
non-respect des mises en garde de sécurité indi-
quées dans ce manuel. Il est très important que ce
manuel d'instructions soit conservé avec l'appa-
reil pour toute consultation future.
Si l'appareil devait être vendu ou transféré à une autre
personne, s'assurer que le manuel soit remis avec ce-
lui-ci, de manière à ce que le nouvel utilisateur puisse
connaître le fonctionnement de la hotte et des mises
en garde relatives.
Après l'installation des hottes en acier inox, il est né-
cessaire d'effectuer le nettoyage de celles-ci pour re-
tirer les résidus de colle de la protection et les taches
éventuelles de graisse et d'huile qui, si on ne les en-
lève pas, peuvent être cause de détérioration irréver-
sible de la surface de la hotte. Pour cette opération,
le fabricant conseille d'utiliser les serviettes fournies,
disponibles même à l'achat.
Exiger des pièces de rechange originales.
Avertissement de la proposition 65 de l'État de
Californie (US seulement)
ATTENTION
Ce produit contient des produits chimiques connus
de l'État de Californie pour causer le
cancer et des malformations congénitales ou d'autres
problèmes de reproduction.
Pour plus d'informations, visitez www.P65Warnings.
ca.gov
DESTINATION D'UTILISATION
L'appareil est destiné, seulement et exclusivement,
pour l'aspiration de fumées générées par la cuisson
d'aliments en milieu domestique, non profession-
nel: toute autre utilisation diérente de celle-ci est
impropre et peut provoquer des dommages à des
personnes, choses et animaux domestiques, et dé-
gage le Fabricant de toute responsabilité.
L'appareil peut être utilisé par des enfants de plus
de 8 ans et des personnes ayant des capacités phy-
siques, sensorielles ou mentales réduites, ou dépour-
vues d'expérience ou de connaissances nécessaires,
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Falmec FDLUM70I5SS-2L Manuale utente
- Categoria
- Cappe da cucina
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: Falmec FDLUM70I5SS-2L User manual
- français: Falmec FDLUM70I5SS-2L Manuel utilisateur
- español: Falmec FDLUM70I5SS-2L Manual de usuario
Documenti correlati
-
Falmec FNLUM36I5SS Manuale utente
-
-
-
-
Falmec FPDPR36I9SS Manuale del proprietario
-
-
-
-
-