Patton electronics Smart-DTA Manuale utente

Tipo
Manuale utente

Questo manuale è adatto anche per

Smart-DTA™
ISDN VoIP Telephone Adapter
Quick Start Guide
Important
—This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Caution
—This device is not intended nor approved for connection to the public ISDN telecommuni-
cation network.
Attention
—Ce dispositif n'est pas prévu ni approuvé pour le raccordement au réseau de
télécommunication public le RNIS.
Vorsicht
—Dieses Gerät ist nicht für Anschaltung an das öffentlich ISDN
Telekommunikationsnetz genehmigt.
Precaución
—Este dispositivo no está previsto ni se ha aprobado para la conexión a la red de
telecomunicaciones pública ISDN.
Attenzione
—Questo dispositivo non è inteso né non approvato per collegamento alla rete di
telecomunicazione pubblica ISDN.
Document Number: 13228U7-001 Rev. B
Part Number: 07MSDTA-QS
Revised: July 23, 2007
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
WWW: www.patton.com
2
Smart-DTA Quick Start Guide
1.0 Power up the Smart-DTA
1.
Connect the Smart-DTA to a power source using the included power supply and cable.
2.
When the
Power
LED stops blinking and remains lit, the Smart-DTA is ready to configure.
The Smart-DTA contains no user serviceable parts. The equipment
shall be returned to Patton Electronics for repairs, or repaired by
qualified service personnel.
Mains Voltage: Do not open the case the power cord is attached. The
external power adaptor shall be a listed limited power source that
incorporates a disconnect device and shall be positioned within easy
reach of the operator. The mains outlet shall be within 10 feet (3
meters) of the device, shall be easily accessible, and protected by a
circuit breaker.
The Smart-DTA is not shipped with power cables. For AC powered
units, ensure that the power cable used meets all applicable stan-
dards for the country in which it is to be installed, and that it is con-
nected to a wall outlet which has earth ground.
Hazardous network voltages are present in WAN ports regardless of
whether power to the Smart-DTA is ON or OFF. To avoid electric
shock, use caution when near WAN ports. when detaching the cables,
detach the end away from the Smart-DTA first.
Do not work on the system or connect or disconnect cables during
periods of lightning activity.
The terminal block header to which the wires are secured provides the disconnect for
the Smart-DTA. Take proper measures to ensure that it is not permanently fastened to
the receptacle mounted on the chassis.
WARNING
CAUTION
Smart-DTA Quick Start Guide
3
2.0 Connect the Smart-DTA to your local network
You must connect the Smart-DTA to an IP network that provides a DHCP server. Using the included black Ethernet
cable, connect the Smart-DTA RJ-45 Ethernet WAN port, labeled
ETH
(see
figure 1
), to an Ethernet hub or switch
on the same network as your PC. The Ethernet WAN interface is configured as a DHCP client.
Figure 1.
Connecting the Smart-DTA to the network via a hub or switch
DHCP
Server
Ethernet Hub
or Switch
Smart-DTA
PC
ETH
port
4
Smart-DTA Quick Start Guide
3.0 Connect the Smart-DTA to an ISDN phone
1.
Using a straight-though cable, terminated with RJ-45 connectors, connect the BRI port of your Smart-DTA
to the S/T port of your ISDN phone, as shown below:
Note: Other pins are not used.
ISDN
Phone
RJ-45, male RJ-45, male
3
4
5
6
3
4
5
6
Smart-DTA Quick Start Guide
5
4.0 Start the SmartNode Discovery Tool
1.
Insert the CD included with your Smart-DTA into the CD drive on your PC.
2.
Copy the file named
SNDiscovery.exe
from the CD to your PC.
3.
At your PC, double-click the
SNDiscovery.exe
file name to activate the tool. The SmartNode Discovery Tool
window will display the IP Address, MAC Address, Device Type (model number) and Build (software
release) of your Smart-DTA.
If your Smart-DTA does not appear:
• Make sure the Smart-DTA and your PC are on the same routed subnet
• Make sure any firewall programs on your PC are disabled
5.0 Access the Web Browser (GUI) Interface
1.
In the SmartNode Discovery Tool window, select the line that displays the IP address of your Smart-DTA.
Figure 2.
SmartNode Discovery Tool window
6
Smart-DTA Quick Start Guide
2.
Right-click the selected line, and select
Webbrowser
. The Login window will display.
Figure 3.
Login window
3.
Enter the username
administrator
. Do not enter a password. Instead simply click OK. Your web browser will
display the Smart-DTA home page.
Figure 4.
Smart-DTA home page
6.0 Configuring your Smart-DTA
Once you have logged in you can use the browser-based graphical user interface (GUI) to configure and manage
your S-DTA. The Smart-DTA home page displays three
Immediate Actions
buttons that allow you to store the cur-
rent configuration state, reload the device, and restore to factory defaults. The home page also displays certain
basic system information. You can always return to the home page by clicking
Home
in the navigation bar.
Smart-DTA Quick Start Guide
7
The GUI consists of the following main elements:
The “Navigation Bar” on the left edge presents you with a menu listing giving access to the various configura-
tion and status pages of the Smart-DTA.
At the top of the page you see the “Current System Path” which displays the location and element currently
presented in the main area.
The rest of the page displays the configuration and status information for the different features of
the Smart-DTA.
7.0 Additional Information
Refer to the
Smart-DTA Getting Started Guide
located on the CD-ROM shipped with your Smart-DTA device and
available online at
www.patton.com/manuals.
For detailed information about:
Installing, configuring, operating, and troubleshooting.
Warranty, trademark & compliance
The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.
A.0 Customer and Technical Support
Toll-Free VoIP support: call
with a VoIP SIP client
Online support: www
.patton.com
E-mail support:
—answered within 1 business day
Telephone support:
Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to
2200 UTC/GMT)
Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800
UTC/GMT)
Fax:
+1 (253) 663-5693
(USA)
or +41 (0)31 985 25 26 (
Switzerland)
Whenever you modify the configuration your Smart-DTA, immediately applies your
changes.Howver, your new settings ARE NOT PERMANENTLY SAVED (in non-volatile
memory [RAM]). To survive power failure or manual reload you must store your new
settings in non-volatile memory. To save your changes: return to the home page and
press the Save Current Configuration button.
IMPORTANT
8
Smart-DTA Quick Start Guide
B.0 Appendix—Factory default IP addresses
Factory default IP addresses and netmask configuration.
C.0 Compliance Information
C.1 Compliance
EMC Compliance:
FCC Part 15, Class A
EN55022, Class A
EN55024
Safety Compliance:
IEC 60950-1
EN60950-1
C.2 Radio and TV interference
The Smart-DTA router generates and uses radio frequency energy, and if not installed and used properly—that
is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television
reception. The Smart-DTA router have been tested and found to comply with the limits for a Class B computing
device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-
sonable protection from such interference in a commercial installation. However, there is no guarantee that
interference will not occur in a particular installation. If the Smart-DTA router does cause interference to radio or
television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct
the interference by one or more of the following measures: moving the computing equipment away from the
receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet
(such that the computing equipment and receiver are on different branches).
IP Address Network mask
WAN interface Ethernet 0 (0/0)
DHCP Client n/a
LAN interface Ethernet 1 (0/1)
192.168.1.1 255.255.255.0
DHCP server address range (LAN)
192.168.1.10-192.168.1.99 255.255.255.0
Smart-DTA Quick Start Guide
9
C.3 EC Declaration of Conformity
(See section
C.4 “EG-Konformitätserklärung”
for German version.)
Product Description:
Smart-DTA
The products described above in the form as delivered are in conformity with the provisions of the following
European Directive:
R&TTE Directive 1999/5/EC
Guidelines of the European Parliament and the Committee for the Harmonization of the Legal Regu-
lations of the Member States concerning radio equipment and telecommunications terminal equip-
ment and the mutual recognition of their conformity.
The signed Declaration of Conformity can be downloaded from
www.patton.com/certifications/.
C.4 EG-Konformitätserklärung
(see section
C.3 “EC Declaration of Conformity”
for English version)
Produktbezeichnung
: Smart-DTA
Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-
gender Richtlinie überein:
R&TTE 1999/5/EG
Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige
Anerkennung ihrer Konformität.
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von:
www.patton.com/
certifications/.
C.5 Authorized European Representative
D R M Green, European Compliance Services Limited.
Oakdene House, Oak Road , Watchfield, Swindon, Wilts SN6 8TD, UK
The safety advice in the documentation accompanying the products shall be obeyed.
The conformity to the above directive is indicated by the CE sign on the device.
Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.
Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem
Gerät bestätigt.
10
Smart-DTA Quick Start Guide
NOTES
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Smart-DTA Quick Start Guide
11
NOTES
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
12
Smart-DTA Quick Start Guide
Copyright statement
Copyright © 2007, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no
liability for errors that may appear in this document.
Trademarks statement
The term
Smart-DTA
is a trademark of Patton Electronics Company. All other trademarks presented in this docu-
ment are the property of their respective owners.
Warranty
For warranty information, refer to the
Smart-DTA Getting Started Guide
located on the CD-ROM that came with
your IAD or available online at
www.patton.com
.
In accordance with the requirements of council directive 2002/96/EC on Waste of
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate
this product from other waste and scrap and deliver to the WEEE collection system in
your country for recycling.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Patton electronics Smart-DTA Manuale utente

Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue