Olivetti Fax-Lab 101 Manuale del proprietario

INSTRUCTIONS

Ink Jet Fax

Fax-Lab 101/121

Fax-Lab S101

Network compatibility declaration

This product has been designed and developed to operate in the networks of all European Community countries,

and in those of Switzerland and Norway.

Full compatibility with the networks of individual countries will depend on specific national software parameters which

can be set in the product. If you encounter problems with non EC PSTN networks, contact your national technical

support service.

Your attention is drawn to the following conditions that could compromise the conformity attested above as well as

the machine’s characteristics:

• incorrect electrical supply;

• incorrect installation, erroneous or improper use, or any use that differs from what is indicated in the User Manual

supplied with the machine;

• replacement of components or original parts using other types, not approved by the manufacturer, or where

carried out by unauthorized persons.

The electrical socket must be near to hand and easily accessible. To disconnect the machine from the electrical power

supply, unplug it from the supply socket.

The manufacturer reserves the right to make any changes to the machine described in this manual, at any time, and

without prior warning.

This machine has been approved, under the terms of Council Decision 98/482/EC, for Europe-wide connection as

a single terminal to an analogue Public Switched Telephone System (PSTN) system. However, due to differences

between individual PSTNs in the various countries, the approval does not unconditionally guarantee success

operation of every PSTN termination point.

If you encounter any problems, you should contact your supplier immediately.

The manufacturers declare under their own responsibility that this product

complies with provisions laid down by the directive 1999/05/CE (the full

declaration can be found at the www.olivetti.com site, by choosing "support",

"Certifications" and then the product name).

Conformance is certified by the application of the mark to the product.

EDITED/PUBLISHED/PRODUCED BY:

Olivetti, S.p.A. con unico azionista

Gruppo Telecom Italia

Direzione e coordinamento di Telecom Italia S.p.A.

Printed in Thailand.

Code of user manual: 256603P-01

Date of publication: June 2005.

No parts of this manual may be photocopied, reproduced or translated into other languages without prior written

authorization from Olivetti S.p.A.

T

ABLE

OF

CONTENTS

-

FIRST

SECTION

B

EFORE

YOU

START

I

CONSULTING THE MANUAL ........................................................ I

ENVIRONMENTAL RECYCLING .................................................... I

SAFETY PRECAUTIONS ............................................................... I

ABOUT THE INSTALLATION AND SETUP PARAMETERS ............ I

A

BOUT

THE

FAX

MACHINE

II

CONSOLE ..................................................................................... II

COMPONENTS ............................................................................ IV

H

OW

TO

GET

STARTED

QUICKLY

V

PACKAGE CONTENTS V

INSTALLATION CONDITIONS V

CONNECTING TO THE TELEPHONE LINE AND

POWER SUPPLY V

SETTING SOME PARAMETERS (INDISPENSABLE

FOR CORRECT FUNCTIONING) VI

TO SET THE LANGUAGE AND THE COUNTRY OF

DESTINATION .............................................................................. VI

TO SET THE DATE AND TIME ................................................... VII

TO CHANGE THE DATE AND TIME .......................................... VIII

ALL THAT IS MISSING NOW IS YOUR NAME AND

FAX NUMBER ............................................................................ VIII

SETTING UP THE FAX MACHINE X

TRANSMISSION XII

WHAT DOCUMENTS MAY BE USED .......................................... XII

TO SEND A DOCUMENT ............................................................ XII

TO HEAR THE DIALLING TONE WHEN SENDING A

DOCUMENT ................................................................................ XII

TO SEND A DOCUMENT WITH THE RECEIVER RAISED ......... XII

RECEPTION XIII

TO CHOOSE THE RECEPTION MODE ..................................... XIII

MANUAL RECEPTION ............................................................... XIII

AUTOMATIC RECEPTION ......................................................... XIII

RECEPTION WITH TELEPHONE ANSWERING DEVICE ........... XIII

RECEPTION IN "PHONE/FAX" MODE .......................................XIV

USING THE TELEPHONE XV

TO TELEPHONE WITH ONE-TOUCH DIALLING ........................ XV

TO TELEPHONE WITH SPEED DIALLING .................................. XV

TO TELEPHONE BY RUNNING A SEARCH IN THE

PHONE BOOK ............................................................................. XV

TO REDIAL ONE OF THE LAST 20 INCOMING NUMBERS

OR ONE OF THE LAST 10 OUTGOING NUMBERS .................. XVI

MAKING COPIES XVI

WHAT DOCUMENTS CAN BE COPIED .....................................XVI

TO MAKE A COPY ...................................................................... XVI

I

B

EFORE

YOU

START

C

ONSULTING

THE

MANUAL

This manual describes various models of fax machine of which some

have a built-in telephone answering device and others do not.

In the description that follows, whenever a distinction is to be made

between these models, reference will be made to: "Base models"

and "Models with a built-in TAD".

This manual is divided into two sections: the first section "About

the fax machine" and "How to get started quickly" provide a

summary of the fax machine's features, allowing you to install it

and get started immediately, using its basic functions only.

After this initial phase, the second section of the manual can be

consulted. In it you will find a detailed description of the fax

machine and its many functions.

E

NVIRONMENTAL

RECYCLING

The cardboard box, the plastic present in the package and the vari-

ous parts of the fax machine may be recycled in accordance with the

recycling regulations in force in your country.

S

AFETY

PRECAUTIONS

RISK OF AN ELECTRIC SHOCK

• Never attempt to repair the fax machine yourself. If you remove

the casing, you risk getting an electric shock or suffering some

other kind of injury. Repairs should be carried out by qualified

technical staff only.

• During storms we recommend you unplug the device from

both the power outlet and the telephone line so as to

eliminate the risk of it being damaged by lightning.

• Never pour liquids on the fax machine and avoid exposing it to the

damp.

If liquids seep inside it, unplug it immediately from the mains power

supply and the telephone line. Before using it again, have it re-

paired by qualified, technical staff.

• Do not use the fax machine outside in bad weather.

• Connect the fax machine exclusively to a certified wall power

socket.

• To unplug the power cable from the wall power socket, remove

the plug and refrain from yanking the cable.

• Never touch the power cable or plug with wet hands.

• Do not fold or squash the power cable. Keep it away from heat

sources.

• Before cleaning the fax machine, unplug it from the wall power

socket.

• Before using the fax machine, check that it has not been damaged

or dropped. If it has, have it checked by a qualified engineer.

RISK OF SUFFOCATION

•

The fax machine and its accessories are wrapped in plastic so do

not let children play with the packaging material.

RISK OF FIRE

• If you are to leave the fax machine unused for a long period of

time, you should disconnect it from the power supply: in this way,

it will be protected against the risk of damage due to interference or

power surges.

RISK OF ACCIDENT

• Place it on a stable, flat surface free of all vibrations so as to avoid

drops that could cause damage to the machine and injury to per-

sons.

•

Lay the power cable so that it cannot be trodden on or tripped

over.

•

Never let children use or play with the fax machine.

OPERATING PRECAUTIONS

• Keep the fax machine in a dust-free place away from sources of

water, steam and excessive heat. Do not expose it to direct sun-

light.

• Ensure that no books, documents, or other objects obstruct normal

ventilation in any way.

• Use the fax machine exclusively at a temperature of between 5°C

and 35°C and a relative humidity of between 15% and 85%.

• Keep the fax machine away from other electrical and electronic

appliances that may cause interference, e.g. radios, televisions,

etc.

• If a voltage drop or power failure occurs, it will not be possible to

make or receive telephone calls as the keypad will be disabled.

• In an emergency, if you wish to make a call, you must use a

telephone certified by the telephone company, connecting it di-

rectly to the fax machine (in countries where this is allowed) or

directly to the telephone wall socket.

• Leave enough room in front of the outlet from which documents

and received/copied documents are unloaded, so that they do not

fall on the floor.

IMPROPER USE

The fax machine was designed to send and receive documents

and to copy paper documents. The machine may also be used as

a telephone. All other uses are to be considered improper. In par-

ticular, it is never to be connected directly to an ISDN line and, if it

is, the guarantee becomes null and void.

A

BOUT

THE

INSTALLATION

AND

SETUP

PARAMETERS

As the country default values for each installation and setup param-

eter may change due to certification requirements or specific cus-

tomers’ needs, these values do not always correspond to those

indicated in the manual: it is therefore advisable to print them before

changing them.

II

A

BOUT

THE

FAX

MACHINE

C

ONSOLE

•

Dial the fax or telephone number.

•

If pressed for more than a second, they automatically dial

(once set) the telephone or fax number assigned to them

(one-touch dialling function).

•

Enter numeric data.

•

Select digits and alphanumeric characters during the en-

try of numbers and names.

"Error" LED indicator

Signals an operating fault during transmission or

reception.

Blinking, indicates that the memory contains docu-

ments that have not been printed.

Off, indicates that the memory is empty.

MODELS WITH A BUILT-IN TA D ONLY

On, indicates that there are messages or memos in the

memory that have already been played.

Blinking, indicates that the memory contains docu-

ments that have not been printed, messages or memos

that have not been played.

Off, indicates that the memory is empty.

With the handset lifted, gives access to the special func-

tions made available by the network manager and com-

monly known as REGISTER RECALL (R function).

•

Scroll "forwards" and "backwards" through the values of a

parameter.

•

Move the cursor to the "right" and to the "left" while entering

numbers and names.

MODELS WITH A BUILT-IN TAD ONLY

•

Used to perform TAD functions. Described in the correspond-

ing chapter.

Display

A two-line liquid crystal display with a capacity of 16 characters

per line.

Shows operator prompts and error messages.

•

After the button has been pressed, it turns

the speaker volume "up" or "down".

•

With tone dialling, they send a tone

down the line for special network serv-

ices.

•

They scroll "backwards" and "for-

wards" through characters and spe-

cial symbols during the entry of

names.

The specific keys of the models with TAD are described under the item “

MODELS WITH A BUILT-IN TAD ONLY

”.

III

A

BOUT

THE

FAX

MACHINE

C

ONSOLE

•

Unloads a document from the ADF.

•

Turns off the " " LED indicator.

•

Returns the fax machine to the stand-by mode.

•

Stops the programming, transmission, reception or

copying operation in progress.

•

Starts receiving a document.

•

After the fax number has been dialled, starts sending a

document (only with the document inserted in the ADF).

•

Confirms the selection of menus, submenus, param-

eters and their values and moves on to the next condi-

tion.

•

Starts copying a document (only with the document

inserted in the ADF).

Used to dial a telephone or fax number without lifting

the telephone handset.

•

After two numeric keys (01-50)

have been pressed, automati-

cally dials (once set) the tel-

ephone or fax number associ-

ated with them.

•

Cancels incorrect settings.

• Inserts a pause during the dialling of the telephone

or fax number.

• Displays a list of the last 10 fax or telephone

numbers dialled (outgoing calls) or the last 20

numbers from which calls have been received

and not answered (incoming calls), irrespec-

tive of whether or not a document was present in

the ADF.

• Adjusts the resolution of the documents to be sent and

copied (only with the document inserted in the ADF).

• Puts the line on hold during a telephone conversation (with

the handset raised).

•

Gives access to programming mode.

•

Selects menus and submenus.

IV

A

BOUT

THE

FAX

MACHINE

C

OMPONENTS

The figure shows the external and internal parts common to the various models of fax machine.

PAPER SUPPORT EXTENSION

CONNECTION SOCKETS

BUILT-IN TELEPHONE

HANDSET

DISPLAY

The display consists of two lines of 16

characters each. It shows the date and

time, menu items, error messages, reso-

lution and contrast values.

PLAIN PAPER FEED COMPARTMENT (ASF)

Maximum capacity: 40 sheets (80gr/m

2

).

AUTOMATIC FEEDER FOR DOCUMENTS TO BE

SENT

AND COPIED (ADF)

MAXIMUM CAPACITY: 5 SHEETS OF A4

OPERATOR CONSOLE

RECEIVED OR COPIED DOCUMENT OUTPUT

SPEAKER

PRINT HEAD

COMPARTMENT

MACHINE SERIAL NUMBER

PLATE

(SEE BASE)

OPTICAL READER

V

H

OW

TO

GET

STARTED

QUICKLY

This section provides a basic description of the fax machine, explaining how to install it and get started quickly, using its basic functions only. For

a more comprehensive use of the fax machine, see the corresponding section.

As this section is designed to give you a gradual and systematic approach to the fax machine, we recommend you read the topics in the

order in which they are presented.

PACKAGE CONTENTS

IMPORTANT

The fax machine is set up to be connected to the

public telephone line. If you want to connect it to a

private line see section "To set it up for the tel-

ephone line".

BA

In addition to the fax machine and this manual, you will find the follow-

ing elements in the package:

• The paper support extension

• The cable for connecting the fax machine to the telephone line.

• The power cable.

• The telephone plug (if applicable).

• The box containing the monochrome print head provided with the

machine.

• The telephone handset.

• Aftersales support information.

IMPORTANT

The use of non-original print heads makes the product’s

guarantee null and void.

INSTALLATION CONDITIONS

Place the fax machine on a stable, flat surface. Make sure there is enough room for ventilation.

Keep the fax machine in a dust-free place away from sources of excessive heat or humidity. Do not expose it to direct sunlight.

CONNECTING TO THE TELEPHONE LINE AND POWER SUPPLY

Connect the fax machine to the telephone line

Connect the telephone handset

VI

H

OW

TO

GET

STARTED

QUICKLY

If a voltage drop or power failure occurs, it may be useful to use an emergency telephone.

IMPORTANT

The plug of the power supply cable may vary from

country to country.

SETTING SOME PARAMETERS (INDISPENSABLE

FOR CORRECT FUNCTIONING)

Once the fax is connected to the power supply, it automatically runs a

short test to check that its components are working and the display

may show:

- the language in which the messages will be displayed

or

- the message "AUTOMATIC 00" ("AUTOMATIC" in the base

models) and, alternating on the second line, the messages "SET

DATE/TIME" and "CHECK PRINT HEAD".

In the first case, to enable the fax machine to work properly, you must

set the language and country in which it is to be used as described in

the procedure below.

In the second case, you can move on to set the date and time directly.

T

O

SET

THE

LANGUAGE

AND

THE

COUNTRY

OF

DESTINATION

The display shows the language in which the messages

are displayed. For example:

ITALIANO

1. To select the desired language, press the keys:

/ The display shows, for example:

ENGLISH

2. To confirm the setting, press the key:

The display shows:

CHOOSE COUNTRY

Connect the fax machine to the power supply

IMPORTANT

To connect the emergency telephone directly to the

fax machine, remove the cover from the socket for

connecting to the external line and then insert the

plug of the emergency telephone in this socket (see

figure opposite).

In countries where this kind of connection is not al-

lowed (for example, Germany and Austria), connect

the emergency telephone directly to the telephone

wall socket.

IMPORTANT

Do not insert the print head before connecting the

fax machine to the power supply socket.

VII

H

OW

TO

GET

STARTED

QUICKLY

T

O

SET

THE

DATE

AND

TIME

The first time you connect the fax machine to the power

supply or whenever there is a power failure you must set

the date and time as described below.

Once set, the date and time can be changed at any time,

see the "To change the date and time" section.

1. Press the key:

The display shows:

DATE AND TIME

2. Press the key:

The display shows:

FORMAT: DD/MM/YY

3. If you want to select a different format from the one dis-

played, press the keys:

/

4. Press the key:

The display shows:

FORMAT: 24 H

5. To select the other time format (12 hours), press the keys:

/ The display shows:

FORMAT: 12 H

6. Press the key:

The display shows:

DD/MM/YY HH:MM

25-10-04 11:23

7. To enter the new date and time (e.g. 26-10-04; 12:00),

press the keys:

- As each digit is entered, the cursor will move to the next

one.

DD/MM/YY HH:MM

26-10-04 12:00

8. If you wish to move the cursor to digits to be modified, press

the keys:

/

9. Then overwrite the digits with the correct ones, by pressing

the keys:

-

3. To confirm the setting, press the key:

The display shows a country of destination, for example:

ITALIA

4. To select the desired country, press the keys:

/ The display shows, for example:

U.K./IRELAND

If your country is not present among those shown on the

display, see the table below:

COUNTRY COUNTRY TO BE SELECTED

Algeria ALGERIA

Bosnia BOSNIA

Bulgaria BULGARIA

Croatia CROATIA

Czech Republic CZECH REPUBLIC

Egypt EGYPT

Greece GREECE

Hungary HUNGARY

Iran IRAN

Israel ISRAEL

Middle East MIDDLE EAST

Morocco MOROCCO

Poland POLAND

RoW INTERNATIONAL

Rumania RUMANIA

Russia RUSSIA

Serbia SERBIA

Slovakia SLOVAKIA

Slovenia SLOVENIA

South Africa SOUTH AFRICA

Tunisia TUNISIA

Turkey TURKEY

5. To confirm the setting, press the key:

6. To complete the procedure, press the key:

note

If you subsequently want to change these settings, press +

and repeat the procedure from the start, remembering always to

confirm the settings made by pressing the

button.

VIII

H

OW

TO

GET

STARTED

QUICKLY

10. To confirm the setting, press the key:

The date and time setting procedure has been completed.

The new date and time will be updated automatically and

will be printed on each page sent.

11. To return the fax machine to its initial stand-by mode, press

the key:

The display shows in the models with built-in telephone

answering device:

AUTOMATIC 00

In the base models:

AUTOMATIC

and alternating on the lower line:

30-10-04 12:02 - CHECK PRINT HEAD

Remember that the stand-by mode is the status in which the fax

machine is idle and that it is the mode from which the machine can be

programmed.

notE

If you have chosen the 12-hour time format, the display will show the

letter "p" (post meridiem) or the letter "a" (ante meridiem). To switch

from one format to the other:

1. Position the cursor, using the

/ keys, below the letter to be

modified.

2. Press the

key.

3. If you think you have made a mistake and want to abort the proce-

dure in progress, press the

key.

T

O

CHANGE

THE

DATE

AND

TIME

If the date and time shown on the display are not correct,

you can change them at any time.

1. Press the key

until the display shows:

FAX SET-UP

2. To confirm the setting, press the key:

The display shows:

DATE AND TIME

From this point follow the procedure previously described

in "To set the date and time".

A

LL

THAT

IS

MISSING

NOW

IS

YOUR

NAME

AND

FAX

NUMBER

Once set, the name (max. 16 characters) and number

(max. 20 digits) will remain unchanged until they are in-

tentionally changed and will be printed on each page re-

ceived by your correspondent’s fax machine.

1. Press the key

until the display shows:

INSTALLATION

2. Press the key:

The display shows:

TEL. LINE SET-UP

3. Press the key

until the display shows:

STATION NAME

4. Press the key:

The display shows:

TYPE YOUR NAME

5. To select the characters of each key cyclically, press the

keys:

-

6. To leave a space, press the keys:

/

7. To include a variety of special symbols, e.g. &, in your

name, press the keys:

-

8. If there are any wrong characters, move the cursor to the

wrong character, by pressing the keys:

/

9. Then overwrite the character with the correct one, by press-

ing the keys:

-

10. To delete the name completely, press the key:

For example, to enter the name "LARA":

Until you have selected the letter "L".

Until you have selected the letter "A".

Until you have selected the letter "R".

Until you have selected the letter "A".

11. To confirm the name, press the key:

The display shows:

PHONE NUMBER

IX

H

OW

TO

GET

STARTED

QUICKLY

Now enter the fax number as indicated below:

TO SET YOUR FAX NUMBER

1. Press the key:

The display shows:

TYPE YOUR NUMBER

2. To enter your fax number, press the keys:

-

3. To leave a space, press the keys:

/

If you make any typing errors, correct them in the same

way as for your name.

If you want to include the international code in your number,

instead of the zeros, press the * key; the display will show

the symbol +.

4. To confirm the fax number, press the key:

5. To return the fax machine to its initial stand-by mode, press

the key:

POSITION OF YOUR NAME AND FAX NUMBER

The information at the top of the document to be sent (name,

fax number, date and time and number of pages) may be

received by your correspondent’s fax machine:

- outside the text area immediately below the top edge of the

sheet;

or

- inside the text area, slightly lower down than in the previous

case.

Your fax machine is designed to send this information inside

the text area.

To change the position:

1. Press the key

until the display shows:

FAX SET-UP

2. Press the key:

The display shows:

DATE AND TIME

3. Press the key:

The display shows:

VARIOUS SETTINGS

4. Press the key

until the display shows:

HEADER INSIDE

5. To select the alternative parameter, press the keys:

/ The display shows:

HEADER OUTSIDE

6. To confirm the setting, press the key:

7. To return the fax machine to its initial stand-by mode, press

the key:

X

AB

H

OW

TO

GET

STARTED

QUICKLY

SETTING UP THE FAX MACHINE

Feed the print paper into the machine

IMPORTANT

If you add sheets (max. 40) to the ASF, make sure

you place them under and not on top of those al-

ready present.

The fax machine has a memory that enables it to

receive up to 19 pages even if you do not add

any paper.

Insert the print head

IMPORTANT

The print head provided with the machine al-

lows you to print up to 80 pages*, whereas the

print heads that you will buy subsequently have a

greater capacity and will thus allow you to print up

to 450 pages*.

* Based on Test Chart ITU-TS n.1 (black

coverage = 3,8%).

AB

XI

Once the print head has been inserted, the operator

console closed and the handset replaced, the fax ma-

chine shows the message: "NEW PRINT HEAD?", "1 = YES,

0 = NO". Set the value 1; the fax machine starts the nozzle

cleaning and checking procedure, which is completed by:

• the printing, on the sheet loaded automatically, of a diag-

nostic test sheet containing:

-a numbered scale, for checking the flow of ink and the

electrical circuits of the print head nozzles.

- a group of graphics and text, so that the printing qual-

ity may be evaluated.

• the display shows the message: "CHECK PRINT OUT",

"1 = EXIT 0 = REPEAT".

Examine the print test sheet as follows:

1. Check that the numbered scale is not broken at any point

and that the black areas do not present any horizontal

white lines: if these conditions, which confirm that the print

head has been inserted correctly and is working properly,

are respected, set the value 1. The fax machine returns

to its

initial stand-by mode and is ready for use. The display shows

the message:

AUTOMATIC 00

25-10-04 11:23

C

D

E

2. On the other hand, if there are any breaks or white lines

present, set 0 to clean the nozzles again: if the new print test

continues to be unsatisfactory, repeat the procedure another

time. At this point:

• if the printing quality still does not meet your expectations,

clean the electrical contacts as indicated in the "To clean

the electrical contacts of the print head" section of the

"Maintenance operations" chapter.

• if the printing quality is satisfactory, set the value 1. The

fax machine returns

to its initial stand-by mode and is

ready for use.

IMPORTANT

When the print head is about to run out of ink, the display

shows:

INK LOW

When there is no ink left, the display shows:

OUT OF INK

To replace the print head, see the section "Maintenance op-

erations".

To buy new print heads, see the corresponding code at

the end of the manual.

H

OW

TO

GET

STARTED

QUICKLY

IMPORTANT

Once the print head provided with the machine is

worn, remember only to use original print heads

(see code printed at the end of the manual).

If, after the print head has been installed, the "CHECK

PRINT HEAD" message appears again, try remov-

ing it and then reinserting it, pressing it more firmly into

position. If the message remains on the display, re-

move the print head and clean the electrical contacts

of the print head and the carriage, see "To clean the

electrical contacts of the print head", section

"Maintenance operations".

XII

H

OW

TO

GET

STARTED

QUICKLY

TRANSMISSION

If you follow the procedures described below, you can immediately use the fax machine to carry out simple transmission operations. In

any case, if these procedures are not enough for you, see the "Transmission and reception operations" chapter, which provides a detailed

description of all the transmission modes and other dialling procedures (one-touch and speed dialling, etc.) for which the fax machine has to be set

up (see "To set one-touch and speed dialling").

T

O

SEND

A

DOCUMENT

If these diagrams are not enough:

è è

see "To send a document", section "Transmission and

reception operations".

T

O

HEAR

THE

DIALLING

TONE

WHEN

SENDING

A

DOCUMENT

If these diagrams are not enough:

è è è

see "To send a document", section "Transmission and

reception operations".

T

O

SEND

A

DOCUMENT

WITH

THE

RECEIVER

RAISED

If these diagrams are not enough:

è è è

see "To send a document", section "Transmission and

reception operations".

W

HAT

DOCUMENTS

MAY

BE

USED

For any type of transmission, the document has to be placed in

the automatic document feeder (ADF).

CHARACTERISTICS OF THE ORIGINAL

• Width 210 mm

• Length 105 mm - 600 mm

• Unit weight 70 - 90 gr/m

2

(max. 5 sheets)

Place the document in the automatic document feeder (ADF) with

the side to be sent face down.

IMPORTANT

If you do not perform any operation within about one

and half minutes of inserting the document in the au-

tomatic document feeder (ADF), the fax machine will

automatically unload the document from the feeder.

XIII

H

OW

TO

GET

STARTED

QUICKLY

T

O

CHOOSE

THE

RECEPTION

MODE

1. Press the key

until the display shows:

RECEPTION MODE

2. Press the key:

The display shows:

AUTOMATIC 00

3. To view the other available options, "MANUAL" and

"PHONE/FAX", press the keys:

/

4. To confirm the setting, press the key:

5. To return the fax machine to its initial stand-by mode, press

the key:

notE

To activate reception with TAD mode, you must first record the

OUTGOING MESSAGE, see "The Telephone Answering Device".

Once you have recorded it, in step 3 of the procedure indicated

above, you can view the option: "TAD/FAX" and then confirm by

pressing the

key.

RECEPTION

You can set up the fax machine to receive the documents sent by your correspondents in four different modes, that you may access by carrying

out the procedure described below. These modes are: manual reception, automatic reception, automatic reception with recognition of the type of

call and, only on models with a built-in TAD, reception with a telephone answering device.

M

ANUAL

RECEPTION

For all occasions in which you are present and you can therefore

answer the calls yourself.

If these diagrams are not enough:

è

see "To receive a document", section "Transmission and

reception operations".

A

UTOMATIC

RECEPTION

For all occasions in which you are out but want to receive docu-

ments anyway. This is the mode originally set on your fax machine.

R

ECEPTION

WITH

TELEPHONE

ANSWERING

DEVICE

In this reception mode, the TAD receives the calls, records any mes-

sages left by the correspondent and, if he wants to send you a

document, enables the fax machine to receive it.

XIV

H

OW

TO

GET

STARTED

QUICKLY

A FAX MACHINE is calling.

Your fax machine is set to re-

ceive automatically.

The remote party called just to

talk to you: at the end of the con-

versation, replace the receiver.

Your fax machine beeps for 20

seconds (set value). The dis-

play shows "LIFT HANDSET".

A TELEPHONE is calling.

20 seconds have passed and you

have not lifted the receiver.

Your fax is set to receive

automaticaly. It will wait to re-

ceive a document for about 30

seconds, then it will return to its

initial stand-by mode.

The remote party asks you to

receive.

PHONE/FAX enabled.

After the

programmed

number of

rings.

Your fax is set to receive.

R

ECEPTION

IN

"

PHONE

/

FAX

"

MODE

The behaviour of the fax machine in this mode depends on who is

calling and whether you are in or not when the fax is received.

The following diagram will help you:

XV

H

OW

TO

GET

STARTED

QUICKLY

USING THE TELEPHONE

When you engage the line by lifting the telephone handset, you may use all the telephone functions available on ordinary telephones sold on

the market.

These also include the R function (REGISTER RECALL, activated by pressing the

key) which provides access to the special services made

available by the company that manages the telephone network.

You can also use the following functions:

•

Call the correspondent using the fast dialling procedures set, see below "To telephone with one-touch dialling" and "To telephone with

speed dialling".

•

Momentarily hold a telephone call by pressing the (HOLD) key. The call is resumed as soon as the same key is pressed again.

T

O

TELEPHONE

WITH

ONE

-

TOUCH

DIALLING

Do not place the document in the ADF.

1. Press the desired numeric key, for example

, for more

than one second.

- The display shows the digits of the telephone number that

you associated with it (see "To set one-touch and speed

dialling", chapter "Transmission and reception opera-

tions"). If you also associated a name with it, the display

will show this, too.

2. Once the number has been dialled, if the correspondent is

free, you can start talking.

The display shows the length of the call in minutes and

seconds in the top right-hand corner.

T

O

TELEPHONE

WITH

SPEED

DIALLING

Do not place the document in the ADF.

1. Lift the handset to engage the line.

The display shows:

OFF HOOK

and the length of the call in minutes and seconds in the top

right-hand corner.

2. Press the key:

The display shows:

TEL CALL

CODE OR < >

3. To type the desired speed dialling code, for example

, press the keys:

- The display shows the digits of the telephone number that

you associated with it (see "To set one-touch and speed

dialling", chapter "Transmission and reception opera-

tions"). If a name was also associated with it, the display

will show this, too.

Once the number has been dialled, if the correspondent is

free, you can start talking.

T

O

TELEPHONE

BY

RUNNING

A

SEARCH

IN

THE

PHONE

BOOK

Do not place the document in the ADF.

1. Lift the handset to engage the line.

The display shows:

OFF HOOK

and the length of the call in minutes and seconds in the top

right-hand corner.

2. Press the key:

The display shows:

TEL CALL

CODE OR < >

3. To locate the telephone number or name of the correspond-

ent you want to call, press the keys:

/

4. To start dialling, press the key:

Once the number has been dialled, if the correspondent is

free, you can start talking.

XVI

H

OW

TO

GET

STARTED

QUICKLY

T

O

REDIAL

ONE

OF

THE

LAST

20

INCOMING

NUMBERS

OR

ONE

OF

THE

LAST

10

OUTGOING

NUMBERS

Do not place the document in the ADF.

1. Lift the handset to engage the line.

The display shows:

OFF HOOK

and the length of the call in minutes and seconds in the top

right-hand corner.

2. Press the key:

The display shows:

INCOMING CALLS

W

HAT

DOCUMENTS

CAN

BE

COPIED

As for transmission, copying requires the document to be

inserted in the automatic document feeder (ADF). Before

making a copy, make sure that the document is correctly inserted in

the feeder and that it respects the characteristics described previ-

ously (see the "Transmission" section).

Bear in mind however that for the copying function you can only

insert one sheet at a time in the automatic document feeder (ADF).

T

O

MAKE

A

COPY

As mentioned previously, you can also use the fax machine

as a photocopier. The printing quality obtained depends

on the type of copy you want to obtain "Normal copy" or

"Quality copy" and the contrast and resolution values

that you select before starting the copying function.

1. Choose the type of contrast on the basis of the following

criteria:

• NORMAL, if the document is neither very light nor very

dark.

• LIGHT, if the document is very dark.

• DARK, if the document is very light.

2. Choose the type of resolution on the basis of the following

criteria:

• TEXT, if the document contains easily legible text or sim-

ple graphics.

• PHOTO, if the document contains shaded areas.

3. To display the other available option, "OUTGOING CALLS",

press the keys:

/

4. To confirm your choice, press the key:

5. To find the telephone number or name of the correspond-

ent you wish to call on the list of the last 20 incoming calls or

on the list of the last 10 outgoing calls, press the keys:

/

6. To start dialling, press the key:

Once the number has been dialled, if the correspondent is

free, you can start talking.

MAKING COPIES

3. Insert the document in the ADF.

The display shows on the top line:

DOCUMENT READY

and on the bottom line, the default contrast value: NOR-

MAL.

4. Press the key:

The display shows the default copy size, contrast and reso-

lution settings: 100%, NORMAL and TEXT, respectively. It

also shows the number of copies set (1).

5. Press the key:

The display shows:

COPY: HIGH QUAL.

6. To view the other available option, "COPY: NORMAL",

press the keys:

/

7. To confirm your choice, press the key:

The display shows:

ZOOM: 100%

8. To choose the desired copy size setting, "140%", "70%" or

"50%", press the keys:

/

9. To confirm your choice, press the key:

The display shows:

CONTRAST:NORM.

La pagina sta caricando ...

Olivetti Fax-Lab 101 Manuale del proprietario

Olivetti Fax-Lab 101 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti