Ubiquiti UniFi Switch 24 US-24-250W Guida Rapida

Managed PoE+ Gigabit

Switch with SFP

Models: US-24-250W, US-24-500W

1G

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®

Switch with SFP. The UniFi Controller software and User Guide

are available for download at: downloads.ubnt.com/unifi

This Quick Start Guide is designed to guide you through the

installation and show you how to access the Configuration

Interface. This Quick Start Guide also includes the warranty

terms, and is for use with the UniFi Switch with SFP,

modelUS‑24‑250W or US‑24‑500W. (The hardware description

and installation instructions are the same for both models.)

Package Contents

1G

UniFi Switch

Managed PoE+ Gigabit

Switch with SFP

Models: US-24-250W, US-24-500W

1G

Power Cord Mounting Screws

(#10‑32 x 5/8", Qty. 4)

Cage Nuts

(#10‑32 x 5/8", Qty. 4)

Quick Start

Guide

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s

responsibility to follow local country regulations and indoor cabling requirements.

Network Topology Requirements

• A DHCP‑enabled network for the UniFi Switch to obtain an

IPaddress (connected devices will also obtain IP addresses

after deployment)

• A management station running the UniFi Controller

software, located either on‑site and connected to the same

Layer2 network, or off‑site in a cloud or NOC

or

UniFi Switch

UniFi

Security

Gateway

Internet

UAP-AC UAP-PRO

LAN

WAN

O-Site

Cloud/NOC

On-Site

Management

Station

Network Health

www

WAN LAN

WLAN

VOIP

www

WAN LAN WLAN VOIP

IP

DNS

GATEWAY

ACTIVE CLIENTS

DOWN

UP

SWITCHES

USERS

GUESTS

DOWN

UP

APS

USERS

GUESTS

DOWN

UP

PHONES

EXTENSION

CALLS IN

CALLS OUT

XXX.XXX.XXX.XXX

192

0

162

2

0

30

4

3

6

0

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENT SITE

Default

REFRESH RATE

2 minutes

Network Health

www

WAN LAN

WLAN

VOIP

www

WAN LAN WLAN VOIP

IP

DNS

GATEWAY

ACTIVE CLIENTS

DOWN

UP

SWITCHES

USERS

GUESTS

DOWN

UP

APS

USERS

GUESTS

DOWN

UP

PHONES

EXTENSION

CALLS IN

CALLS OUT

XXX.XXX.XXX.XXX

192

0

162

2

0

30

4

3

6

0

DASHBOARD

MAP

DEVICES

CLIENTS

CALLS

STATISTICS

INSIGHTS

SETTINGS

CURRENT SITE

Default

REFRESH RATE

2 minutes

1G

UAP-Outdoor+

Sample Network Diagram

All UniFi devices support off‑site management controllers.

For setup details, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

Front Panel System LED

1G

System

State Status

White Factory defaults, waiting for integration.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not use or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Successfully integrated into a network

and working properly.

Flashing Blue

This is used to locate a device.

When you click Locate in the UniFi

Controller software, the System LED

will flash blue. The software will also

display the location of the UniFi Switch

on the map.

Front Panel Port LEDs

1G

RJ45: PoE

RJ45: Speed/Link/Act

1G

SFP: Speed/Link/Act

LED State Status

RJ45 1‑24

PoE

Off No PoE

Amber IEEE 802.3af/802.3at

Green 24V Passive

Speed/

Link/

Act

Off No Link

Amber

Link Established at

10/100Mbps

Flashing Indicates Activity

Green

Link Established at

1000Mbps

Flashing Indicates Activity

SFP 1‑2

Speed/

Link/

Act

Off No Link

Green

Link Established at 1Gbps

Flashing Indicates Activity

Front Panel Ports

1G

RJ45 1-24

SFP 1-2

Port Description

RJ45 1‑24

RJ45 ports support Power over Ethernet (PoE)

and 10/100/1000 Ethernet connections.

SFP 1‑2

Hot‑swappable SFP ports support 1 Gbps

connections.

Front Panel Button

Reset

1G

Button Description

Reset

This button serves two functions for the

UniFi Switch:

• Restart Press and release the Reset

button quickly.

• Restore to Factory Default

Settings Press and hold the Reset button

for more than five seconds.

*640-00083-03*

640-00083-03

Back Panel

CONSOLE

Mounting Holes

Power

Mounting Holes

Console

Note: The Console port is reserved for future use.

Side Panels

Ventilation Holes

Fans

Installation Requirements

• Phillips screwdriver

• Standard‑sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks

from the most brutal environments and devastating ESD

attacks with industrial‑grade shielded Ethernet cable,

TOUGHCable

™

, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the UniFi Switch itself should be housed inside a

protective enclosure.

Hardware Installation

1. Connect the Power Cord to the Power port of the

UniFiSwitch.

2. Attach the UniFi Switch to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts

with the Mounting Screws.)

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.

3. Connect the other end of the Power Cord to a power outlet.

Connecting Ethernet

1. Connect an Ethernet cable from your computer or host

system to any port of UniFi Switch.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

2. Connect Ethernet cables from the Ethernet ports of your

devices to the other numbered ports of the UniFi Switch.

Note: The PoE settings for ports 1-24 are set to

auto‑sensing PoE+ by default, so 802.3af/at devices

can be plugged in and automatically receive PoE. For

instructions on how to enable 24V passive PoE, refer

to the Configuring PoE Settings section.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a compatible fiber module into the SFP port.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

3. Connect a fiber optic cable to the fiber module. Then

connect the other end of the cable to another fiber device.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

50

For information about compatible fiber SFP modules, visit:

community.ubnt.com/unifi

Software Installation

Download and install the latest version of the UniFi Controller

software at downloads.ubnt.com/unifi and follow the

on‑screen instructions.

Note: If you already have UniFi Controller v4.3.x or higher

installed, skip to the section, Adopting the UniFi Switch.

After you have installed the software and run the UniFi

Installation Wizard, a login screen will appear for the UniFi

Controller management interface. Enter the admin name and

password that you created and click Login.

You can manage your network and view network statistics

using the UniFi Controller management interface.

To adopt the UniFi Switch, proceed to the Adopting the UniFi

Switch section.

For information on configuring and using the UniFi

Controller software, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Adopting the UniFi Switch

1. From the UniFi Controller dashboard, click DEVICES in the

left menu bar.

2. On the Devices screen, locate the UniFi Switch in the list of

devices under the Name/MAC Address column. To adopt

the UniFi Switch, click ADOPT.

3. The System LED on the UniFi Switch will turn blue to

confirm that it has been successfully adopted.

To configure PoE settings, proceed to the Configuring PoE

Settings section.

Configuring PoE Settings

The PoE settings for ports 1-24 are set to auto‑sensing PoE+

by default, so 802.3af/at devices can be plugged in and

automatically receive PoE.

WARNING: Before activating 24V passive PoE, ensure

that the connected device supports PoE and the

suppliedvoltage.

1. On the Devices screen, locate the UniFi Switch in the list of

devices under the Name/MAC Address column. Double‑click

its Name/MAC Address to access its settings.

2. Click the Ports tab.

3. Click Actions for the port you want to configure.

4. Select the appropriate mode: Off, 24V Passive, or PoE+

from the PoE setting. ThenclickApply.

For more information, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Specifications

UniFi Switch

Dimensions

485 x 43.7 x 285.4 mm (19.09 x 1.72 x 11.24")

Weight

US‑24‑250W

US‑24‑500W

4.7 kg (10.4 lb)

4.8 kg (10.6 lb)

Total Non‑Blocking Line Rate

26 Gbps

Max. Power Consumption

US‑24‑250W

US‑24‑500W

250W

500W

Power Method 100‑240VAC/50‑60 Hz, Universal Input

Power Supply

US‑24‑250W

US‑24‑500W

AC/DC, Internal, 250W DC

AC/DC, Internal, 500W DC

Certications CE, FCC, IC

Rack‑Mount Yes, 1U High

ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV

Operating Temperature ‑5 to 40° C (23 to 104° F)

Operating Humidity 5 to 95% Noncondensing

Shock and Vibration ETSI300‑019‑1.4 Standard

LEDs Per Port

Serial Console Port N/A

RJ45 Data Ports PoE, Speed/Link/Activity

SFP Data Ports Speed/Link/Activity

Interfaces

Networking Interfaces (24) 10/100/1000 Mbps RJ45 Ethernet Ports

(2) 1 Gbps SFP Ethernet Ports

Management Interface (1) RJ45 Serial Port (Reserved for Future Use)

Ethernet In/Out Band

PoE Per Port

PoE Interfaces

POE+ IEEE 802.3af/at (Pins 1, 2+; 3, 6‑)

24VDC Passive PoE (Pins 4, 5+; 7, 8‑)

Max. PoE+ Wattage per

Port by PSE

34.2W

Voltage Range 802.3at

Mode

50–57V

Max. Passive PoE Wattage

per Port

17W

24V Passive PoE Voltage

Range

20‑27V

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error‑free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

CAN ICES‑3(A)/NMB‑3(A)

This Class A digital apparatus complies with Canadian CAN ICES‑3(A).

CAN ICES‑3(A)/NMB‑3(A)

Cet appareil numérique de la classe A est conforme à la norme NMB‑3(A)

Canada.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

La pagina sta caricando ...

Ubiquiti UniFi Switch 24 US-24-250W Guida Rapida

Questo manuale è adatto anche per

Ubiquiti UniFi Switch 24 US-24-250W Guida Rapida

in altre lingue

Documenti correlati

Altri documenti