Yamaha Stagepas 400BT Manuale utente

Marca: Yamaha

Modello: Stagepas 400BT

Tipo: Manuale utente

Questo manuale è adatto anche per

Stagepas 600BT

Owner’s Manual

Mode d’emploi

Manual de instrucciones

EnglishFrançaisEspañol

2 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

이 기기는 가정용(B급) 전자파적합기기로서 주로

가정에서 사용하는 것을 목적으로 하며, 모든

지역에서 사용할 수 있습니다.

(class b korea)

FCC CAUTION

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : PORTABLE PA SYSTEM

Model Name : STAGEPAS 600BT, STAGEPAS 400BT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(fcc_sengen)

English

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual 3

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, fire

or other hazards. These precautions include, but are

not limited to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip

over, or roll anything over it.

• Only use the voltage specified as correct for the mixer.

The required voltage is printed on the name plate of the

mixer.

• Use only the supplied power cord.

If you intend to use the device in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt

or dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is

not unplugged from the wall AC outlet, the device will not

be disconnected from the power source.

• Remove the electric plug from the outlet when the device

is not to be used for extended periods of time, or during

electrical storms.

• Be sure to connect to an appropriate outlet with a

protective grounding connection.

Do not open

• This device contains no user-serviceable parts. Do not

open the device or attempt to disassemble the internal

parts or modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers

(such as vases, bottles or glasses) containing liquids

which might spill into any openings. If any liquid such as

water seeps into the device, turn off the power

immediately and unplug the power cord from the AC

outlet. Then have the device inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• Avoid setting all equalizer controls and level controls to

their maximum. Depending on the condition of the

connected devices, doing so may result in feedback that

can cause hearing loss and damage the speakers.

• Before connecting the device to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set

to the minimum. Failing to do so may result in hearing loss,

electric shock, or device damage.

• When turning on the AC power in your audio system,

always turn on the device LAST, to avoid hearing loss and

speaker damage. When turning the power off, the device

should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames near the

device, since they may cause a fire.

Wireless unit

• Do not use this device near medical devices or inside

medical facilities. Radio waves from this device may affect

electro-medical devices.

• Do not use this device within 15 cm (6 in) of persons with

a heart pacemaker implant or a defibrillator implant. Radio

waves from this device may affect electro-medical

devices, such as a heart pacemaker implant or

defibrillator implant.

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from

the outlet.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the

device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualified

Yamaha service personnel.

• If this device should be dropped or damaged,

immediately turn off the power switch, disconnect the

electric plug from the outlet, and have the device

inspected by qualified Yamaha service personnel.

4 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the device or other property. These

precautions include, but are not limited to, the following:

Power supply/power cord

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

Location

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

• Do not block the vents. This mixer has ventilation holes at

the top and sides to prevent the internal temperature from

becoming too high. In particular, do not place the mixer on

its side or upside down. Inadequate ventilation can result

in overheating, possibly causing damage to the mixer, or

even fire.

• If you install the mixer apart from the speakers:

- Do not cover it with any cloth.

- Make sure the top surface faces up; do not install on its

sides or upside down.

- Do not use the device in a confined, poorly-ventilated

location.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even fire. Make sure

that there is adequate space around the device: at least

30 cm above, 30 cm at the sides and 30 cm behind.

• If you lay the speaker flat on its side or like a stage

monitor, make sure to remove the mixer first.

• Do not use the speaker’s handles for suspended

installation. Doing so can result in damage or injury.

• Do not hold the bottom of the speaker when transporting

or moving it. In doing so, you may pinch your hands under

the speaker, and result in injury.

• Do not place the device in a location where it may come

into contact with corrosive gases or salt air. Doing so may

result in malfunction.

• Before moving the device, remove all connected cables.

Connections

• For the SPEAKERS jacks of the mixer, use only the

included MODEL 600S or MODEL 400S speakers and

speaker cables. Use of other types of speakers and

cables may result in damage, or even fire.

Maintenance

• Remove the power plug from the AC outlet when cleaning

the device.

Handling caution

• Do not insert your fingers or hands in any gaps or

openings on the vents or panel of the mixer, and the ports

of the speaker.

• Avoid inserting or dropping foreign objects (paper,

plastic, metal, etc.) into any gaps or openings on the vents

or panel of the mixer, and the ports of the speaker. If this

happens, immediately turn off the power of the mixer,

unplug the power cord from the AC outlet, and have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy

objects on it. Avoid applying excessive force to the

buttons, switches or connectors to prevent injuries.

• Do not operate the device if the sound is distorting.

Prolonged use in this condition could cause overheating

and result in fire.

• Avoid pulling the cables such as microphones to prevent

injuries or damage to the speakers and mixer by causing

them to fall.

Yamaha cannot be held responsible for damage caused

by improper use or modifications to the device.

English

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual 5

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other

property, follow the notices below.

■ Handling and maintenance

• Do not expose the device to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid,

drastic changes in ambient temperature—when the

device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the

device while condensation is present can cause damage.

If there is reason to believe that condensation might have

occurred, leave the device for several hours without

turning on the power until the condensation has

completely dried out.

• Protection Circuit: This speaker system has an internal

protection circuit that shuts off the speaker unit when an

excessive input signal is applied. If the speaker unit emits

no sound, reduce the volume level of the amplifier

immediately. The sound will return automatically in several

seconds.

• When placing the speaker face down, always place it on a

flat surface.

• Do not touch the speaker driver unit.

• The rubber feet included in this package can be attached

to the speaker to prevent slippage when it is to be used on

a slippery surface.

• Air blowing out of the bass reflex ports is normal, and

often occurs when the speaker is handling program

material with heavy bass content.

• Always turn the power off when the device is not in use.

■ Connectors

• XLR-type connectors are wired as follows (IEC60268

standard):

pin 1: ground

pin 2: hot (+)

pin 3: cold (–).

Information

■ About this manual

• The illustrations as shown in this manual are for

instructional purposes only.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

■ About disposal

• This product contains recyclable components.

When disposing of this product, please contact the

appropriate local authorities.

The Bluetooth

word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of

such marks by Yamaha Corporation is under license.

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and

retain this manual as a permanent record of your purchase to aid iden-

tification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

Features

6 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Thank you for purchasing the Yamaha STAGEPAS 600BT/400BT Portable PA System! The STAGEPAS is an all-in-one portable PA system,

consisting of two dedicated speakers and a powered mixer. It is designed to amplify music or speeches at live events or during other

productions.

This owner’s manual explains how to set up and operate the STAGEPAS for use as a loudspeaker for music and speeches by individuals,

companies, or schools. To get the most out of your new STAGEPAS and its sophisticated functions, we suggest that you read through this

manual thoroughly, and keep it in a safe place for future reference.

Table of Contents

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Model description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Attaching a speaker to a speaker stand . . . . . . . . . . . . . . . . . . .7

Attaching non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Controls and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Quick Start Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using a Bluetooth

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Features

• High-output power amplifier for versatility in a wide variety of performance

applications.

• Two-way bass-reflex type speakers for high-quality, powerful sound.

• Multi-channel mixer supports a wide range of inputs.

• Bluetooth input for wireless high-quality sound from smartphones or tablets.

• Yamaha’s high-quality SPX reverb, which provides optimum processing for

instruments or vocals.

• Feedback Suppressor, which automatically cuts and prevents undesirable feedback

noise.

• Independent equalizer on each channel for tonal adjustment and sound control.

• Main unit

(Dedicated speakers (STAGEPAS 600BT: MODEL 600S,

STAGEPAS 400BT: MODEL 400S) x 2, powered mixer x 1)

• Power cord (2m) x 1

• Speaker cables (6m) x 2

• Non-skid pads x 12

• Ferrite core x 2

• Cable tie x 2

• Owner’s Manual (this book)

Packag e Contents (Please confirm that all items are included.)

English

Model description

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Model description

There are two models of Bluetooth-enabled STAGEPAS. The following table describes

the differences in mixer functions between these models.

NOTE

This manual primarily uses the STAGEPAS 600BT for purposes of explanation.

Attaching a speaker to a speaker stand

Attach the speaker to the speaker stand with the lock lever moved up (release

position).

2. Move the lock lever down to lock to the stand.

Attaching non-skid pads

If you plan to lay the speaker flat on its side, attach the included non-skid pads in the

locations indicated by arrows in the figure below.

Model name Line-in channels Equalizer

STAGEPAS 600BT CH 5/6, CH7/8, CH9/10 HIGH, MID, LOW

STAGEPAS 400BT CH 5/6, CH7/8 HIGH, LOW

Lock lever

1. Release

2. Lock

Controls and Functions

8 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Controls and Functions

1 Mic/Line input jacks (channels 1-4)

Connect microphones, guitars, electronic musical

instruments or audio equipment.

Channels 3 and 4 provide combo jacks that

support both XLR and phone plugs.

2 MIC/LINE switches (channels 1-4)

For low-level signals (including microphones), set the switch to the MIC ()

position. For high-level signals (including electronic instruments and audio

equipment), set the switch to the LINE ( ) position.

4 5 8

M O

XLR Phone

English

Controls and Functions

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

3 Hi-Z switch (channel 4)

This switch is used when connecting a device directly to the mixer without a DI

(direct box) — for example, instruments with passive pickups, such as an

acoustic-electric guitar or electric bass without a battery. This function is effective

only for the phone jack input.

4 Line (stereo) input jacks

STAGEPAS 600BT (channels 5/6, 7/8, 9/10)

STAGEPAS 400BT (channels 5/6, 7/8)

Connect line-level devices such as electronic

instruments, acoustic-electric guitars, CD

players, and portable audio players. These

jacks support phone, RCA-pin, and stereo-mini

plugs.

NOTE

For the channel 7/8 input (STAGEPAS 600BT), or for the channel 5/6 input (STAGEPAS

400BT), if both phone and RCA-pin jacks are used at the same time, the phone jack will take

priority. For the channel 9/10 input (STAGEPAS 600BT), or the channel 7/8 (STAGEPAS

400BT), if both phone and stereo mini jacks are used at the same time, the stereo mini jack

will take priority. The signal from the device connected to another jack will be muted. The

signals from the Bluetooth device specified by the Bluetooth button

9 are always mixed to

channels 9/10 (STAGEPAS 600BT) or channels 7/8 (STAGEPAS 400BT).

5 MONITOR OUT jacks

These connect to powered speakers for monitoring purposes, and output a mix of

the signals from channels 1 to 9/10 (STAGEPAS 600BT) or channels 1 to 7/8

(STAGEPAS 400BT). You can adjust the output level using the MONITOR OUT

control

A. If only the L (MONO) jack is used, the signals from the L and R

channels are mixed and output.

6 SUBWOOFER OUT jack

This connects to a powered subwoofer, and outputs a mono signal. If this jack is in

use, the low frequencies below 120Hz to the SPEAKERS L/R jacks will be cut. The

output level is linked to that of the MASTER LEVEL control

7 REVERB FOOT SW jack

This connects to an unlatched-type footswitch, such as the Yamaha FC5. This can

be useful for solo performers, since you can toggle the reverb on and off as

needed with your foot.

8 SPEAKERS L/R jacks

Use the included speaker cables to connect the dedicated speakers.

9 Bluetooth button/LED

This button switches the Bluetooth function on or off. It is also used to pair

(register) a Bluetooth device (page 15). The Bluetooth LED indicates the following

status:

NOTE

The STAGEPAS enables you to pair (register) up to eight Bluetooth devices. Once the ninth

Bluetooth device has been paired successfully, the pairing information for the Bluetooth

device that was connected earliest will be deleted.

0 PHANTOM (CH1/2) switch /LED

When this switch is on, the LED lights up, indicating that phantom power is

available for channels 1 and 2. Turn this switch on to supply power to condenser

microphones or a DI (direct box).

Notice

Follow the important precautions below to prevent noise and possible damage to external

devices and the unit when you operate this switch.

• Be sure to leave this switch off if you do not need phantom power, or when you connect a

device that does not support phantom power to channels 1 or 2.

• Do not connect/disconnect a cable to/from channels 1 and 2 while this switch is on.

• Turn the LEVEL control of the channels 1 and 2 to the minimum before operating this

switch.

A MONITOR OUT control

Determines the signal level output from the MONITOR OUT jacks

The MASTER LEVEL control does not affect the MONITOR OUT signal.

B Equalizer controls (HIGH, MID*, LOW) *Only for STAGEPAS 600BT

This three-band equalizer adjusts the channel’s high, mid*, and low frequency

bands. Setting the control to the “ ” position produces a flat response in the

corresponding band. Turning the control clockwise boosts the selected band. If

you start getting feedback, turn the control back slightly.

C REVERB switch/LED

When this switch is on, the LED lights up, indicating that you can apply reverb.

This switch is off when you turn on the unit. (Unlike other switches, this switch

cannot be locked.)

RCA Pin Stereo Mini

LED Status

Off Bluetooth off

Lit steadily Bluetooth connected

Flashing slowly Waiting for Bluetooth connection

Flashing fast Pairing a Bluetooth device

Controls and Functions

10 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

D REVERB TYPE/TIME control

Determines the reverb type and length. Turning the control to the right lengthens

the time of the selected reverb type.

HALL: Simulated reverb of a large space, such as a concert hall.

PLATE: Simulated metal plate reverb, producing a more hard-edged and bright

sound.

ROOM: Simulated acoustic ambience of a small room.

ECHO: Echo effect suitable for vocals.

E REVERB controls (channels 1-4)

Determines the amount of reverb for each channel when the REVERB switch

C is

on.

F ST/MONO switches

STAGEPAS 600BT (channels 5/6, 7/8, 9/10)

STAGEPAS 400BT (channels 5/6, 7/8)

Setting the switch to ST (STEREO) () will assign the signals from the L and R

channels to each left and right speaker and output each signal. Setting the switch

to MONO ( ) will mix the output of different L and R sources to output the same

signal to both the left and right speakers. For keyboards with mono output, guitars,

or other non-stereo sound sources, when the switch is set to MONO ( ), the stereo

input jacks can be conveniently used as multiple mono jacks.

G LEVEL meter

The LEVEL meter shows the level of output signal from the SPEAKERS L/R jacks.

Notice

If the unit is operated at a sufficiently high volume to make the LIMITER LED flashes

continuously, the internal power amplifier section is being excessively overloaded and may

malfunction. Reduce the output level with the MASTER LEVEL control so that the indicator

flashes only briefly on the highest transient peaks.

H POWER LED

This LED lights when the power is turned on by pressing the power switch.

I FEEDBACK SUPPRESSOR switch/LED

When this switch is on, the LED lights up, indicating that feedback is automatically

suppressed. (This configuration utilizes a seven-band notch filter. When this switch

or the power switch is off, the notch filter will be reset.)

J LEVEL controls

Use these controls to adjust the volume for each channel. To reduce noise, set any

LEVEL controls on unused channels to the minimum.

K MASTER EQ (equalizer) control

Use this control to adjust the overall sound frequency balance. The center position

“MUSIC” is a basic setting. If you turn the control counterclockwise, it will create an

optimum setting for speech, cutting unneeded low range frequencies. If you turn

the control clockwise, it will create an optimum setting for playback of sound

sources, since the low range is boosted. If you turn the control further clockwise,

the LED will light up, indicating that the bass boost function turns on, giving you an

even more powerful bass tone.

L MASTER LEVEL control

Determines the volume of the signal output from the SPEAKERS L/R jacks. This

allows you to adjust the overall volume without changing the relative volume

balance among the various channels.

M Vents

These are the vents for the cooling fan inside the mixer.

Do not block the vents when in use.

N AC IN jack

Connect the included power cord here.

O (power) switch

For turning the power of the mixer on ( ) and off ().

NOTE

Rapidly turning the unit on and off in succession may cause it to malfunction. After turning the

unit off, wait for about 5 seconds before turning it on again.

English

Quick Start Guide

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Quick Start Guide

Connecting the speakers and the mixer

Slide the mixer’s lock in the direction of the arrow (shown below), and then

remove it from the speaker.

2. Open the cover panel attached to the other speaker, and then remove the box

from inside the accessory compartment.

Two speaker cables and one power cord are included in the box.

NOTE

After the box is removed, loose items, such as the included power cord, speaker cables, and

an optional microphone can be conveniently stored in the accessory compartment.

3. Connect the speakers and the mixer.

Connect the mixer’s SPEAKERS jacks (red) to the speakers’ input jacks (red) using

the included speaker cables. As shown in the illustration below, be sure to insert

the speaker cables all the way inside until secure.

Notice

Use only the included speaker cables. Use of other cables may result in heat generation, or

short circuiting.

Accessory

compartment

Cover panel

Input jack

SPEAKERS jack

Quick Start Guide

12 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Connecting microphones, instruments, and audio

devices to the mixer

4. Connect desired devices, such as a microphone, or an instrument to the input

jack of the mixer.

Refer to the illustration on the mixer shown below or the connection example of the

cover panel of the accessory compartment.

Getting sound out of the system

5. Connect the included power cord as described in the steps below: Before

connecting the power cord, make sure that the power to the STAGEPAS is

turned off.

5-1 Connect the plug on the included power cord to the AC IN jack on

the rear panel of the unit.

5-2 Connect the other end of the power cord to a power outlet.

NOTE

To disconnect the power cord, reverse these steps.

Warning

The STAGEPAS has been designed for grounded use. To avoid electrical shock and damage

to devices, be sure to ground the unit using the included power cord. If you have any

questions regarding connections, contact your nearest Yamaha dealer.

Warning

Use only the included power cord. Otherwise, heat may be generated or electrical shock may

be caused.

Notice

Even when the power switch is turned off, a minimal amount of electric current is still flowing

to the unit. If you plan not to use the unit for an extended period of time, be sure to unplug the

power cord from the AC outlet.

6. Turn the mixer’s LEVEL controls (white knobs) and MASTER LEVEL control

(red knob) to the minimum (zero).

Also, set the equalizer controls (green knobs) to the center “ ” or “MUSIC”

position.

Equalizer

English

Quick Start Guide

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

7. Set the MIC/LINE switch to the MIC ( ) position to connect a microphone, and

to the LINE ( ) position to connect a musical instrument or audio device.

8. Turn on the power of the connected sound source (if applicable), then the

mixer.

The POWER LED lights.

9. Set the MASTER LEVEL control to the “ ” position.

10. While playing your instrument or singing into the microphone, use the LEVEL

control to adjust the volume of the corresponding channel.

11. Use the MASTER LEVEL control to adjust the overall volume.

If you hear the sound and the volume seems appropriate, setup is complete. If not,

please refer to the checklist in the “Troubleshooting” section.

NOTE

To avoid loud, unexpected noise from the speaker, first turn off the power to the mixer, then

the connected sound source (such as a musical instrument or audio device).

When the volume is too loud

Turn the LEVEL control to the minimum (zero). Set the MIC/LINE

switch to the LINE ( ) position, then slowly raise the LEVEL control

until the desired volume is reached.

When the volume is too soft

Turn the LEVEL control to the minimum (zero). Set the MIC/LINE

switch to the MIC () position, then slowly raise the LEVEL control

until the desired volume is reached.

Adjusting the volume

Quick Start Guide

14 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Applying Reverb

The STAGEPAS features a built-in reverb processor that is in the same league as our

famed SPX effect processor series. This reverb lets you simulate the acoustics of

different performance environments, such as concert halls and small clubs, and add a

warm, natural ambience to your vocals or instrumental performance.

The following reverb types are included:

Press down the REVERB switch to turn it on.

The LED lights when REVERB is on.

2. Position the REVERB TYPE/TIME control to the desired reverb type and time

(length).

Turning the control to the right lengthens the time of the selected reverb type.

3. Use the REVERB control to adjust the reverb amount of the corresponding

channel.

If necessary, repeat steps 2 and 3 to determine the optimum reverb setting.

Type Description

HALL

Simulated reverb of a large space, such as a concert hall. Suitable for

acoustic guitars, strings, woodwind instruments, etc.

PLATE Simulated metal plate reverb. Adds bright reverb to vocals.

ROOM

Simulated acoustic ambience of a small space. Suitable for percussive

instruments with a strong attack.

ECHO Articulated echo effect suitable for vocals.

Longer

Shorter

English

Using a Bluetooth® device

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Using a Bluetooth

device

You can use the STAGEPAS to play audio files stored in Bluetooth devices, such as a

mobile device.

Pairing a Bluetooth

device

Before you can connect a Bluetooth device for the first time, you need to “pair” the device.

“Pairing” refers to registering a Bluetooth device to another Bluetooth device.

Once pairing is complete, you will be able to reconnect those devices easily after you

terminate a Bluetooth connection.

Make sure that the Bluetooth LED is turned off. If the LED is lit steadily or

flashing, press the Bluetooth button to switch off the Bluetooth function.

2. Press and hold down the Bluetooth button for three seconds or longer.

The Bluetooth LED will flash rapidly, indicating that the unit is ready for pairing.

3. Turn on the Bluetooth function on the Bluetooth device that you want to pair.

For more information, refer to the owner’s manual for the Bluetooth device.

4. Once the Bluetooth device displays a list of other Bluetooth devices that are

available for connection, select STAGEPAS 600BT or STAGEPAS 400BT.

When the pairing process is complete, the Bluetooth connection will be

established and the Bluetooth LED will light up.

NOTE

• The STAGEPAS enables you to pair (register) up to eight Bluetooth devices. Once the ninth

Bluetooth device has been paired successfully, the pairing information for the Bluetooth

device that was connected earliest will be deleted.

• You must complete the pairing process on the Bluetooth device within two minutes.

Connecting a Bluetooth

device

Press and hold down the Bluetooth button for one second.

The Bluetooth LED will flash slowly, indicating that the unit is ready for connection.

2. Turn on the Bluetooth function on the Bluetooth device that you want to

connect.

Select STAGEPAS 600BT or STAGEPAS 400BT from the list of Bluetooth devices

displayed on your Bluetooth device. When the connection is made, the Bluetooth

LED will light up.

Playing audio files stored in a Bluetooth

device

Play an audio file on your Bluetooth device.

Signals from the Bluetooth device are input to channels 9/10 (STAGEPAS 600BT)

or channels 7/8 (STAGEPAS 400BT).

We recommend that you set the volume on the Bluetooth device a little higher than

normal, and then adjust the volume for each channel using the LEVEL controls.

Disconnecting the Bluetooth

device

To disconnect the Bluetooth device, do one of the following:

• Use the Bluetooth device to disconnect. (The Bluetooth LED on the unit will flash

slowly, indicating that the unit is disconnected and waiting for connection.)

• Press the Bluetooth button on the unit to turn off the Bluetooth function. (The

Bluetooth LED will turn off.)

Notice

Before you turn off the power to the unit, make sure that the Bluetooth function is turned off

(The Bluetooth LED is turned off). If you turn off the power to the unit while the Bluetooth

function remains enabled, the unit might lose the pairing information.

NOTE

After turning the Bluetooth function off, wait for at least 6 seconds before turning it on again.

The Bluetooth function will not turn on even if you press the Bluetooth button immediately

after you turn the function off.

If you receive a call or text message while playing audio files on your Bluetooth device such

as a smartphone, the audio file playback might be paused momentarily.

To avoid this interruption, enable Airplane Mode, and then set Bluetooth to ON on your

smartphone.

Troubleshooting

16 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Troubleshooting

Power does not turn on.

 Did you firmly and securely connect the power cord?

Power shuts down suddenly.

 Are the vents of the mixer blocked?

Since inadequate ventilation can result in overheating the

mixer, the power may be turned off automatically to

protect the system from overheating. Arrange the

ventilation for cooling, then turn on the power again.

No sound is heard.

 Did you connect the mixer’s SPEAKERS jacks and the

speakers’ input jacks using the proper speaker cables?

 Did you firmly and securely connect the speaker

cables?

 Is a speaker other than the included speaker

connected to the mixer’s SPEAKERS jacks?

Please connect the included speaker (STAGEPAS 600BT:

MODEL 600S; STAGEPAS 400BT: MODEL 400S).

 Did you use the included speaker cables?

If you use a commercially-available speaker cable with a

metal-housing connector, the cable will be shorted when

the connector touches other metal, resulting in no sound

being produced.

 Is the POWER LED flashing at intervals?

There may be a short in the speaker cable or the

connection may be faulty. Check that the speaker cable

is not scratched and is connected properly to the mixer,

then reapply the power.

 For channels 7/8 (STAGEPAS 600BT) or channels 5/6

(STAGEPAS 400BT), are both phone and RCA-pin

jacks connected at the same time?

Or, for channels 9/10 (STAGEPAS 600BT) or channels

7/8 (STAGEPAS 400BT), are both phone and stereo

mini jacks connected at the same time?

For channels 7/8 (STAGEPAS 600BT), or channels 5/6

(STAGEPAS 400BT), the phone jack takes priority. For

channels 9/10 (STAGEPAS 600BT), or channels 7/8

(STAGEPAS 400BT), the stereo mini jack takes priority.

 Is the POWER LED flashing continuously?

If the internal power amplifier section is excessively

overloaded, the amplifier will be muted for protection. The

mixer will automatically reset itself after a while.

Sound is distorted or noise is produced

 Are the LEVEL controls of all relevant channels and/or

the MASTER LEVEL control set too high?

 Is the MIC/LINE switch of the corresponding channel

set to MIC?

If the input level from the source is high, setting the MIC/

LINE switch to MIC may result in a distorted sound. Set

the switch to LINE position.

 Is the volume of the connected device too high?

Lower the volume of the external device.

 Is the speaker cable or the power cord located near the

input cables?

Please keep it away from the input cables.

Sound is not loud enough

 Are the LEVEL controls of all relevant channels and/or

the MASTER LEVEL control set too low?

 Is the MIC/LINE switch of the corresponding channel

set to LINE?

Turn the LEVEL control to the minimum (zero). Set the

switch to the MIC position, then slowly raise the LEVEL

control.

 Is the volume of the connected device too low?

Raise the volume of the external device.

 Is the PHANTOM switch set to On when using a

microphone that requires phantom power?

The high sounds and low sounds are

unbalanced.

 Are the equalizer controls raised or lowered too much?

Set the equalizer controls to the center position.

 Is the speaker properly outputting high-frequency

range signals?

If not, check the “Protective circuit (poly switch)” note in

the Notice section.

Cannot connect Bluetooth / Bluetooth audio

sound cuts intermittently

 The unit may be connected to a different Bluetooth

device.

Cut the current Bluetooth connection, and then connect

to the desired Bluetooth device.

 The STAGEPAS may be located too far away from the

Bluetooth device.

The maximum distance between the STAGE PAS and a

Bluetooth device should be 10 meters. Locate the

Bluetooth device closer to the STAGEPAS.

 Your Bluetooth device may not support the A2DP

profile.

Use a Bluetooth device that supports A2DP.

 The unit may be located in the vicinity of a device that

emits electro-magnetic waves at a frequency of 2.4

GHz (such as a wireless microphone transmitter,

wireless LAN device, microwave oven, etc).

Locate the STAGEPAS away from any device that emits

electro-magnetic waves.

If your Bluetooth device also features a wireless LAN

function, turn off the function, and use only the Bluetooth

function.

If a problem persists, please contact your Yamaha dealer.

English

Specifications

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Specifications

General Specifications

Dedicated Speaker

STAGEPAS 600BT STAGEPAS 400BT

System Type Powered mixer with 2 passive speakers

Maximum Output Power

(SPEAKERS L/R)

340 W+340 W/4 Ω

@Dynamic at 1 kHz

280 W+280 W/4Ω

@10 % THD at 1 kHz

≥

0 W+230 W/

4Ω

% THD at 1 kHz

200 W+200 W/4 Ω

@Dynamic at 1 kHz

180 W+180 W/4Ω

@10 % THD at 1 kHz

≥ 125 W+125 W/4Ω

@1 %

THD at 1 kHz

Frequency Response

-3 dB, +1 dB @ 40 Hz-20 kHz,

1 W

Output/4Ω (without EQ and SP EQ) (SPEAKERS L/R)

-3 dB, +1 dB @ 40 Hz-20 kHz, +4 dBu 10 kΩ Loa

(MONITOR OUT)

Total Harmonic Distortion

≤

.5 % @

20 Hz-20 kHz,

1 dBu 10 kΩ (MONITOR OUT)

Hum & Noise

(Rs= 150 Ω,

MIC/LINE switch=MIC)

≤ -113 dBu Equivalent input

noise (CH

1–4)

≤ -113 dBu Equivalent input

noise (CH1–4)

≤ -58 dBu Residual output

nois

e (SPEAKERS L/R)

≤

-60 d

Bu Residual ou

tput

ise (SPEAKERS L/R)

Crosstalk (1 kHz) ≤ -70 dB between input channels

Phantom Voltage +30 V (CH1, 2)

Outputs

SPEAKERS OUT (L, R), MONITOR OUT (L/MONO, R),

SUBWOOFER OUT (MONO) with auto HPF

Dimensions (W x H x D)

Speaker 335 x 545 x 319 mm,

Mixer 348 x 197 x 135 mm

Speaker 289 x 472 x 275 mm,

Mixer 308 x 180 x 116 mm

Weight

25.6 kg (56.4 lbs)

(Speaker 10.9 kg x 2 +

Mixer 3.8 kg)

18.3 kg (40.3 lbs)

(Speaker 7.7 kg x 2 +

Mixer 2.9 kg)

Power Requirement 100V–240V 50Hz/60Hz

Power Consumption 35 W (Idle), 100 W (1/8 Power) 30 W (Idle), 70 W (1/8 Power)

Input Channel Equalization

±15 dB ±15 dB

HIGH 8 kHz shelving HIGH 8 kHz shelving

MID 2.5 kHz peaking —

LOW 100 Hz shelving LOW 100 Hz shelving

Bluetooth Connection

Bluetooth Version Bluetooth Ver.4.1

Supported Profile A2DP v1.2

Supported Codec SBC, AAC

Supported Content

Protection

SCMS-T content protection method

Wireless Output Bluetooth class 2

Maximum

communication range

10m (without interference)

Transmission

Frequencies

2402–2480 MHz

Maximum output power

(EIRP)

4 dBm (2.5 mW)

Packag e Contents

Main unit (Dedicated speakers:

(MODEL 600S) x 2,

powered

mixer x 1),

Power cord (2m) x 1,

Speaker cables (6m) x 2,

Non-skid pads x 12,

Ferrite core x 2, Cable tie x 2,

Owner’s Manual (this book)

Main unit (Dedicated speakers:

(MODEL 400S) x 2,

powered

mixer x 1),

Power cord (2m) x 1,

Speaker cables (6m) x 2,

Non-skid pads x 12,

Ferrite core x 2, Cable tie x 2,

Owner’s Manual (this book)

MODEL 600S MODEL 400S

Enclosure 2 way bass-reflex type

Speaker Unit

LF: 10" (25 cm) Cone

HF: 1.4" (3.56 cm) Compression

Driver

LF: 8" (20 cm) Cone

HF: 1" (2.54 cm) Compression

Driver

Crossover Frequency 2.8 kHz 3.2 kHz

Frequency Range 55 Hz–20 kHz (-10 dB)

Maximum Output Level

129 dB SPL

(Measured peak IEC noise@1m)

125 dB SPL

(Measured peak IEC noise@1m)

Coverage Angle 90° (Horizontal) / 60° (Vertical)

STAGEPAS 600BT STAGEPAS 400BT

Specifications

18 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Input Characteristics

STAGEPAS 600BT

STAGEPAS 400BT

Input Terminals MIC/LINE Input Impedance Source Impedance

Input Level

Connector Type

Sensitivity Nominal

Max. before

Clipping

CH IN 1-2 XLR

MIC

3 kΩ 150 Ω Mics

-56 dBu -35 dBu -10 dBu

XLR-3-31

LINE -30 dBu -9 dBu +16 dBu

CH IN 3-4

XLR

MIC

3 kΩ 150 Ω Mics

-56 dBu -35 dBu -10 dBu

XLR Combo

LINE -30 dBu -9 dBu +16 dBu

Phone

MIC

10 kΩ

(Hi-Z 1 MΩ)

150 Ω Lines

(Hi-Z 10 kΩ)

-50 dBu -29 dBu -4 dBu

LINE -24 dBu -3 dBu +22 dBu

CH IN 5/6 Phone — 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone*

CH IN 7/8

Phone — 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone*

Pin — 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu RCA Pin

CH IN 9/10

Phone — 10 kΩ 150 Ω Lines -18 dBu +3 dBu +28 dBu Phone*

mini — 10 kΩ 150 Ω Lines -18 dBu +3 dBu +28 dBu Stereo Mini

Input Terminals MIC/LINE Input Impedance Source Impedance

Input Level

Connector Type

Sensitivity Nominal

Max. before

Clipping

CH IN 1-2 XLR

MIC

3 kΩ 150 Ω Mics

-56 dBu -35 dBu -10 dBu

XLR-3-31

LINE -30 dBu -9 dBu +16 dBu

CH IN 3-4

XLR

MIC

3 kΩ 150 Ω Mics

-56 dBu -35 dBu -10 dBu

XLR Combo

LINE -30 dBu -9 dBu +16 dBu

Phone

MIC

10 kΩ

(Hi-Z 1 MΩ)

150 Ω Lines

(Hi-Z 10 kΩ)

-50 dBu -29 dBu -4 dBu

LINE -24 dBu -3 dBu +22 dBu

CH IN 5/6

Phone — 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu Phone*

Pin — 10 kΩ 150 Ω Lines -24 dBu -3 dBu +22 dBu RCA Pin

CH IN 7/8

Phone — 10 kΩ 150 Ω Lines -18 dBu +3 dBu +28 dBu Phone*

mini — 10 kΩ 150 Ω Lines -18 dBu +3 dBu +28 dBu Stereo Mini

English

Specifications

STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Output Characteristics

STAGEPAS 600BT

STAGEPAS 400BT

0 dBu=0.775 Vrms

Phone*: Unbalanced

Descriptions in this manual are based on specifications available at the time of publication. The latest version of the manual can be downloaded from the Yamaha website.

Output Terminals

Output

Impedance

Load Impedance

Output Level

Connector Type

Nominal

Max. before

Clipping

Typ at THD+N 10% Dynamic

SPEAKERS OUT [L,R] <0.1 Ω 4 Ω Speakers 62.5 W 230 W 280 W 340 W Phone*

MONITOR OUT [L,R] 600 Ω 10 kΩ Lines +4 dBu +20 dBu — — Phone*

SUBWOOFER OUT 150 Ω 10 kΩ Lines -3 dBu +17 dBu — — Phone*

Output Terminals

Output

Impedance

Load Impedance

Output Level

Connector Type

Nominal

Max. before

Clipping

Typ at THD+N 10% Dynamic

SPEAKERS OUT [L,R] <0.1 Ω 4 Ω Speakers 37.5 W 125 W 180 W 200 W Phone*

MONITOR OUT [L,R] 600 Ω 10 kΩ Lines +4 dBu +20 dBu — — Phone*

SUBWOOFER OUT 150 Ω 10 kΩ Lines -3 dBu +17 dBu — — Phone*

Specifications

20 STAGEPAS 600BT/STAGEPAS 400BT Owner’s Manual

Dimensions

STAGEPAS 600BT STAGEPAS 400BT

Unit: mm

110.5

115 2

135

348

197

335

34.8 - 35.2

545

319

144

50°

354

Mixer

Dedicated Speaker

Screw holes for the Mic Stand Adapter

BMS-10A (optional)

Pole diameter

289

472

275

133

50°

304

180

308

95.5

100

116

34.8 - 35.2

Mixer

Dedicated Speaker

Pole diameter

Screw holes for the Mic Stand Adapter

BMS-10A (optional)

La pagina sta caricando ...

Yamaha Stagepas 400BT Manuale utente

Marca: Yamaha

Modello: Stagepas 400BT

Tipo: Manuale utente

Questo manuale è adatto anche per

Stagepas 600BT

Scarica il pdf

rapporto

in altre lingue

English: Yamaha Stagepas 400BT User manual

Yamaha Stagepas 400BT Manuale utente

Questo manuale è adatto anche per

Yamaha Stagepas 400BT Manuale utente

in altre lingue

Documenti correlati

Altri documenti