Yamaha CBX-K1 Manuale del proprietario

Marca: Yamaha

Modello: CBX-K1

Categoria: Strumenti musicali

Tipo: Manuale del proprietario

M.D.G., EMI Division © Yamaha Corporation 1995

VT05800 502PTCP18.2-01A0 Printed in Japan

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

IMPORTANT:

When connecting this product to accessories and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC authorization to use this product in the USA.

NOTE:

This product has been tested and found to comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential environment will not result in

harmful interference with other electronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in the user’s manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in all installations. If this product is found to be

the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following measures:

• Relocate either this product or the device that is being affected by the interference.

• Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC

line filter/s.

• In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is

300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate, please contact

Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park

CA, 90620

• This applies only to products distributed by Yamaha Corporation of America.

CANADA

THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE

EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION

OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT

LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES

DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE

DES COMMUNICATIONS DU CANADA.

* This applies only to products distributed by Yamaha Canada Music LTD.

* Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Music LTD.

Dit produkt is gefabriceerd in overeenstemming met

de radiostoringsvoorschriften van de Richtlijn van de

Raad (82/499/EEG).

ΑΥΤΗ Η ΣΥΣΚΕΥΗ ΑΝΤΑΠΟΚΡΙΝΕΤΑΙ ΣΤΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΤΩΝ Ο∆ΗΓΙΩΝ ΤΗΣ ΕΥΡΩΠΑΙΚΗΣ

ΟΙΚΟΝΟΜΙΚΗΣ ΚΟΙΝΟΤΗΤΑΣ 82/499/Ε.Ο.Κ.

Este produto está de acordo com o radio de

interferencia frequente requiridos do Conselho

Diretivo 82/499/EEC.

Dette apparat overholder det gaeldende EF-direktiv

verdrørende radiostøj.

Cet appareil est conforme aux prescriptions de la

directive communautaire 87/308/CEE.

Diese Geräte entsprechen der EG-Richtlinie 82/499/

EWG und/oder 87/308/EWG.

This product complies with the radio frequency

interference requirements of the Council Directive 82/

499/EEC and/or 87/308/EEC.

Questo apparecchio è conforme al D.M.13 aprile 1989

(Direttiva CEE/87/308) sulla soppressione dei

radiodisturbi.

Este producto está de acuerdo con los requisitos sobre

interferencias de radio frequencia fijados por el

Consejo Directivo 87/308/CEE.

YAMAHA CORPORATION

Model CBX-K1

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION (U.S.A.)

This product utilizes batteries or an external power

supply (adapter). DO NOT connect this product to

any power supply or adapter other than one

described in the manual, on the name plate, or

specifically recommended by Yamaha.

This product should be used only with the compo-

nents supplied or; a cart, rack, or stand that is

recommended by Yamaha. If a cart, etc., is used,

please observe all safety markings and instruc-

tions that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is be-

lieved to be correct at the time of printing. How-

ever, Yamaha reserves the right to change or

modify any of the specifications without notice or

obligation to update existing units.

This product, either alone or in combination with

an amplifier and headphones or speaker/s, may be

capable of producing sound levels that could

cause permanent hearing loss. DO NOT operate

for long periods of time at a high volume level or

at a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should

consult an audiologist. IMPORTANT: The louder

the sound, the shorter the time period before

damage occurs.

NOTICE:

Service charges incurred due to lack of knowledge

relating to how a function or effect works (when

the unit is operating as designed) are not covered

by the manufacturer’s warranty, and are therefore

the owners responsibility. Please study this

manual carefully and consult your dealer before

requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both

user safe and environmentally friendly. We sin-

cerely believe that our products and the produc-

tion methods used to produce them, meet these

goals. In keeping with both the letter and the spirit

of the law, we want you to be aware of the follow-

ing:

Battery Notice:

This product MAY contain a small non-recharge-

able battery which (if applicable) is soldered in

place. The average life span of this type of battery

is approximately five years. When replacement

becomes necessary, contact a qualified service

representative to perform the replacement.

This product may also use “household” type bat-

teries. Some of these may be rechargeable. Make

sure that the battery being charged is a recharge-

able type and that the charger is intended for the

battery being charged.

When installing batteries, do not mix old batteries

with new, or with batteries of a different type.

Batteries MUST be installed correctly. Mismatches

or incorrect installation may result in overheating

and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any

battery. Keep all batteries away from children.

Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with

any retailer of household type batteries in your

area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond

repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local,

state, and federal regulations that relate to the

disposal of products that contain lead, batteries,

plastics, etc. If your dealer is unable to assist you,

please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the

product. The model number, serial number, power

requirements, etc., are located on this plate. You

should record the model number, serial number,

and the date of purchase in the spaces provided

below and retain this manual as a permanent

record of your purchase.

92-BP

PLEASE KEEP THIS MANUAL

Welcome to the CBX-K1

Congratulations and thank you for purchasing the Yamaha CBX-K1 MIDI Keyboard!

The CBX-K1 is a sophisticated, yet compact MIDI keyboard controller, for use with

computers and MIDI music systems. It allows you to play connected tone generators

and rhythm machines, and enter performance data to sequencers and computers. It

features a sophisticated touch-sensitive keyboard that can be adjusted to cover the full

128-note MIDI range. It also provides a wealth of MIDI controls that allow you to

send virtually any MIDI message directly from the keyboard. Moreover, the CBX-K1

has a versatile ASSIGNABLE Wheel that lets you control a wide variety of parameters

on your connected tone generator or sequencer in real time. Because of its exceptionally

portable size, convenient battery/AC adaptor power supply, compatibility with Gen-

eral MIDI (GM) and XG, and extraordinarily powerful and comprehensive MIDI

control functions, the CBX-K1 is an invaluable tool — a MIDI Swiss army knife, of sorts

— for all MIDI musicians and performers.

IMPORTANT

■

The CBX-K1 does not contain an internal tone generator. In order to

play sounds from the CBX-K1, you need an external tone generator, such as the

Yamaha MU series or TG series tone generators.

NOTE

■

The many MIDI functions and features of the CBX-K1 may not be supported

by your particular MIDI device. Be sure to refer to the owner’s manual of your par-

ticular MIDI device when using it with the CBX-K1.

Table of Contents

The CBX-K1 — What It Is and What It Can Do . . . . . . 1

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

How to Use This Manual . . . . . . . . . . . . . . . . . . . . . 3

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Panel Controls and Terminals . . . . . . . . . . . . . . . . . 4

■ Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

● Note Range of the CBX-K1 . . . . . . . . . . . . . 5

■ Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

● Default Settings of the CBX-K1 . . . . . . . . . . 6

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■ Using a Power Adaptor . . . . . . . . . . . . . . . . . . . . 7

■ Using Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

■ When to Replace the Batteries . . . . . . . . . . . . . . . 7

Guided Tour

Setting Up Your CBX-K1 . . . . . . . . . . . . . . . . . . . . . 8

What You’ll Need . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Making the Connections . . . . . . . . . . . . . . . . . . . . . . 9

Using the CBX-K1 — Basic Operations . . . . . . . . . . 10

Playing the Keyboard and Other Operations . . . . . 10

Using the SHIFT-Related Functions . . . . . . . . . . . . 12

● Basic Operations . . . . . . . . . . . . . . . . . . . . 13

Setting the Functions . . . . . . . . . . . . . . . . . . . . . . . 14

● Group A Operations . . . . . . . . . . . . . . . . . . 14

● Group B Operations . . . . . . . . . . . . . . . . . . 16

Reference

Group A Functions . . . . . . . . . . . . . . . . . . . . . . . . 18

Group B Functions . . . . . . . . . . . . . . . . . . . . . . . . 20

ASSIGNABLE Wheel — Controller Number List . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 23

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . 24

MIDI Implementation Chart . . . . . . . . . . . . . . . . . . 26

The CBX-K1 — What It Is and What It Can Do

What It Is

The CBX-K1 is a compact, highly portable 37-key MIDI

keyboard, designed especially for use with computers and

MIDI music systems. The CBX-K1 does not generate any

sound itself, but can be used as a keyboard controller for

playing sounds on a connected tone generator or rhythm

machine. It’s also ideal for recording to sequencers and

computers. The keyboard is touch-sensitive and its octave

range can be changed to cover the full 128-note MIDI

range.

The true power and flexibility of the CBX-K1 is in its

comprehensive MIDI controls. The CBX-K1 allows you to

send virtually any type of MIDI message to connected

MIDI devices. Pre-programmed commands provide easy

control of basic sequencer/rhythm machine functions such

as Start, Stop, Tempo and Song Select, while comprehen-

sive program change commands let you easily select

program banks and voices.

Most importantly, though, the CBX-K1 has an ASSIGN-

ABLE Wheel that can be set for control of any controller

number. This means that you can use the ASSIGNABLE

Wheel to control a wide variety of parameters on your

connected tone generator — such as Volume, Pan, Bright-

ness, and the Depth of various effects — in real time. This

gives you expressive control over different aspects of the

sound in live performance.

The CBX-K1 is also the latest instrument in the Yamaha

line to support the XG format, a new addition to the

General MIDI standard. In short, XG provides for more

instrument sounds and variations, and greater expressive

control over voices and effects. With the use of the

ASSIGNABLE Wheel on the CBX-K1, you have direct

real-time control over many of these newly supported

functions and parameters.

What It Can Do

Here are a few application ideas on how you can use the

CBX-K1. The list below is not comprehensive, but is

meant to be a general guide to the possibilities and provide

a starting point or springboard for your own creative ideas

and explorations.

● Using With a MIDI Tone Generator

In one of the most basic setups, you can play a connected

tone generator from the CBX-K1. Because it’s so compact

and portable, you can even use it as a hand-held keyboard

for live performance.

● Using as a Second Keyboard or Dedicated

MIDI Controller

The CBX-K1 is small enough to fit on top of nearly any

keyboard, making it perfect as a second keyboard. Since

the CBX-K1 has a MIDI IN terminal, you can connect it

between your main keyboard and your tone generator, and

use the extensive MIDI capabilities of the CBX-K1 for

greater expressive control during your performance.

● Using in a MIDI Music System

Combined with a laptop computer and a compact tone

generator (like the General MIDI/XG-compatible Yamaha

MU80), the CBX-K1 gives you comprehensive music

making power — for recording, composing, arranging,

practicing, and editing — in a portable system that’s ready

to go wherever you go. The CBX-K1 is an ideal addition

to larger MIDI studios as well, since it provides far greater

MIDI control and flexibility than nearly any other keyboard

controller. Use it along side your main MIDI keyboard as a

kind of MIDI Swiss army knife — sending necessary MIDI

messages, working the real-time controllers, or editing

already recorded sequencer tracks.

● Multimedia

Since it’s portable and compatible with the General MIDI

and XG formats, the CBX-K1 is a natural for multimedia

applications. Because of its ease of use and comprehensive

functions, it’s the only keyboard you’ll ever need for

recording and editing MIDI data on your multimedia

creations.

● ELECTROMAGNETIC INTERFERENCE

Avoid using the unit near televisions, radios or other

equipment generating electromagnetic fields. Proximity to

such equipment may cause the unit to malfunction, and may

generate interference noise in the other appliance as well.

● DO NOT OPEN THE CASE OR TRY REPAIRING

THE INSTRUMENT YOURSELF

The instrument contains no user-serviceable parts. Never

open the case or tamper with the internal circuitry in any

way, since doing so may result in damage to the instrument.

Refer all servicing to qualified Yamaha service personnel.

● MIDI CABLES

When connecting the instrument to other MIDI equipment,

be sure to use only high-quality cables made especially for

MIDI data transmission. Also, avoid using cables longer

than 15 meters, since long cables can result in data errors.

Precautions

Your CBX-K1 will give you years of reliable service if you

follow the simple precautions below:

● LOCATION

Keep the instrument away from locations where it is likely

to be exposed to high temperatures (such as direct sunlight)

or humidity. Also avoid locations which are subject to

excessive dust accumulation or vibration which could

damage the instrument.

● USE THE CORRECT POWER ADAPTOR

Use only the recommended PA-1B or PA-3 Power Adaptor

for supplying power. Use of another adaptor may cause

serious damage to the instrument or the adaptor itself. Also

avoid using a multiple-plug adaptor; plug the adaptor

directly into a wall outlet.

● MAKE SURE POWER IS OFF WHEN MAKING

OR REMOVING CONNECTIONS

To prevent damage to the instrument and other connected

equipment, always turn off the power prior to connecting or

disconnecting cables. Also, turn the power off when the

instrument is not in use, and disconnect the power adaptor

during electric storms.

● NO MEMORY BACKUP

The CBX-K1 has no internal memory backup. As a result,

all settings are returned to the factory default when turning

the power off.

● HANDLE THE INSTRUMENT WITH CARE

Although the instrument has been constructed to withstand

the rigors of normal use for optimum sturdiness and

reliability, avoid subjecting it to strong physical shocks

(such as dropping or hitting it). Since the CBX-K1 is a

precision-made electronic device, also avoid applying

excessive force to the various controls. When moving the

instrument, first unplug the power adaptor and all other

cables to prevent damage to cords and jacks. Always

unplug cables by gripping the plug firmly, not by pulling

on the cable.

● CLEAN WITH A SOFT, DRY CLOTH

Never use solvents such as benzine or thinner to clean the

instrument, since these will damage the cabinet finish or

dull the keys. Wipe clean with a soft, dry cloth. If neces-

sary, use a soft, clean, slightly moistened cloth — making

sure to wipe the instrument off again with a dry cloth. Do

not leave vinyl on the panel as this may stick to and

discolor the surface.

Yamaha is not responsible for damage caused by

improper handling or operation.

By and large, the CBX-K1 is very easy to use and this manual is self-explanatory. However, we strongly recommend that you

take time to read the manual — especially before trying some of the more sophisticated MIDI functions. Read through all of

the initial sections first, then go on to the “Guided Tour” to set up your CBX-K1, learn how to use its various functions, and

try out some of the practical application examples to help you become more familiar with its operations. For those who need

to delve deeper, the “Reference” section provides at-a-glance information and important details on all functions.

The following conventions are used throughout this manual:

* Panel buttons and controls are indicated as they appear on the actual instrument. (For example, C and

* The functions and features assigned to the keyboard are shown like this: T and {.

* Unless indicated otherwise, L refers to either of the ENTER keys, J or K.

However, when you wish to enter a decimal value, make sure to press K. Likewise, when entering a

hexadecimal number, make sure to press J.

* Actual MIDI data messages (in hexadecimal) are indicated as follows: <<FE>> and <<En 00 40>>, etc.

* Operation steps are indicated as follows:

Example Actual Operation

C + E While holding down the C button, press E (D2).

C + U → L While holding down the C button, first press U (Fm2), then press

L (either J or K).

How to Use This Manual

Specifications

● Keyboard

37 mini key keyboard (C2-C5), velocity responsive

● Functions

Basic: Octave Shift (+/- 4 octaves), Pitch Bend, Assignable

control, MIDI Merge (MIDI IN)

MIDI Data: Sequencer control, MIDI clock, Bank Select,

Program Change, GM System On, XG System On,

GM-B Reset, Control Change, All Sound Off, Reset All

Controllers, and others

Assignable Parameters: Transpose (+/- 12 semitones), MIDI

Transmit Channel, Fixed Velocity, Touch Sensitivity,

Device Number, Merge On/Off (each channel)

● Panel Controls and Indicators

SHIFT button, OCTAVE SHIFT Q/W buttons and lamps,

PITCH Wheel, ASSIGNABLE Wheel, POWER ON/OFF switch

● Input/Output Terminals

MIDI IN, MIDI OUT, DC IN

● Power Supply

Yamaha PA-3 or PA-1B AC Power Adaptor (sold separately),

or six “AA” size, SUM-3, R-6 or equivalent batteries (sold

separately).

● Power Consumption

Approximately 35 mA (with battery use); approximately 2 W

(with AC adaptor use).

● Dimensions (W x D x H)

509 x 155 x 55 mm (20-1/16” x 6-1/8” x 2-3/16”)

● Weight (without batteries)

1.3 kg (2 lbs., 14 oz.)

Panel Controls and Terminals

■ Front Panel

q Keyboard

The CBX-K1 has a 37-key, 3-octave keyboard (C2 to C5),

featuring initial touch (velocity) control. All note on, note

off and velocity data is transmitted via the MIDI OUT

terminal. When used with the C button, the keys are

used for changing various settings and sending special

MIDI messages. (See page 12.)

About the Functions of the CBX-K1: The functions are

divided into two groups: Group A and Group B. The

Group A functions are shown on the panel, above the

left section of the keyboard. The Group B functions are

“hidden” and are listed on pages 12 and 20. Several

functions can be used by pressing only the relevant key;

in other words, pressing L is not necessary. These

functions, such as Sequencer Stop and Start, are shown

on the panel without underline. The right section of the

keyboard serves as value entry and is used for those

functions whose names are underlined on the panel and

require value entry, such as Program Change and

Tempo. Functions whose names appear with a dashed

underline on the panel (for example, GM ON and XG

ON) require pressing L. Value entry on the CBX-

K1 can be done in two number systems: Decimal and

Hexadecimal. The keys labeled A through F are for

Hexadecimal entry.

NOTE

■

The normal (default) velocity range of the

CBX-K1 is from 16 to 127. The range differs accord-

ing to the Touch Sensitivity setting (see page 20).

w PITCH Wheel (Pitch Bend)

This spring-loaded Wheel controls Pitch Bend. The

Wheel’s operation can be reversed. (See page 20.)

e ASSIGNABLE Wheel

When the CBX-K1 is turned on, this Wheel (with center

detent) is set to control Modulation Depth on the connected

MIDI device. It can be set to control other functions; see

pages 18 and 22 for details. The Wheel’s operation can be

reversed. (See page 20.)

r C Button

This button is used to access the “hidden” functions of the

CBX-K1. Used with the N /

M buttons, it allows you to step up or down

through program numbers. (See page 10.) Used with the

keys of the keyboard, it allows you to access the sophisti-

cated MIDI control functions. (See page 12.)

t N / M Buttons

These buttons are used to change the octave range of the

keyboard, allowing you to play across the entire range of

MIDI notes (C-2 to G8). (See page 5.) Press both of these

buttons together to restore the normal octave setting (C2 to

C5). With the C button, these buttons can also be

used to step up or down through program numbers on the

connected MIDI device. (See page 10.)

STOP CONTINUE START

SOUND

OFF

MERGE

ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0

TRANSPOSE

HEXA

DECIMAL

DC IN

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET

PITCH

ASSIGNABLE

IN MIDI OUT

ENTER

DRUM

NUMBER

NRPN

CONTROLLER

RPN

FIXED

VELOCITY

MIDI

PROGRAM

CHANGE

BANK

SELECT

TEMPO

PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER

POWER ON OFF

SHIFT

GM

XG

MIDI KEYBOARD CBX-K1

CONTROLLER NUMBER LIST

122 COARSE TUNING

(NRPN)

(RPN)

120 PITCH BEND SENSITIVITY

121 FINE TUNING

123 VIBRATO RATE

124 VIBRATO DEPTH

125 VIBRATO DELAY

126 FILTER CUTOFF FREQUENCY

127 FILTER RESONANCE

128 EG ATTACK TIME

129 EG DECAY TIME

130 EG RELEASE TIME

131 DRUM FILTER CUTOFF FREQUENCY

132 DRUM FILTER RESONANCE

133 DRUM EG ATTACK RATE

134 DRUM EG DECAY RATE

135 DRUM PITCH COARSE

136 DRUM PITCH FINE

137 DRUM LEVEL

138 DRUM PAN

139 DRUM REVERB DEPTH

140 DRUM CHORUS DEPTH

141 DRUM VARIATION DEPTH

142 CHANNEL PRESSURE

143 POLYPHONIC KEY PRESSURE

144 MASTER VOLUME

145 MASTER BALANCE

146 MASTER TUNING

147 VELOCITY

148 TEMPO

OTHERS

74 BRIGHTNESS

84 PORTAMENTO CONTROL

91 REVERB DEPTH

92 TREMOLO DEPTH

93 CHORUS DEPTH

94 VARIATION DEPTH

95 PHASER DEPTH

73 ATTACK TIME

1 MODULATION DEPTH

5 PORTAMENTO TIME

6 DATA ENTRY

7 MAIN VOLUME

8 BALANCE CONTROL

10 PANPOT

CONTROL CHANGE

2 BREATH CONTROL

4 FOOT CONTROL

64 HOLD1(DAMPER)

65 PORTAMENTO

66 SOSTENUTO(CHORD HOLD)

67 SOFT PEDAL

69 HOLD2 (FREEZE)

71 HARMONIC CONTENT

72 RELEASE TIME

11 EXPRESSION

uw e

y V / B Lamps

These lamps provide several indications:

* During normal playing conditions, these indicate the

octave setting of the keyboard, up (B) or down

(V). Both light together for the normal octave

setting. When changing the octave setting, these flash

to indicate the number of octaves, up or down. (See

page 11.)

* When using some of the “hidden” functions, these flash

when a MIDI message is transmitted or when a function

is executed.

* The left lamp flashes slowly when the battery power is

too low for proper operation.

* The right lamp flashes quickly when there is some kind

of MIDI receive error. The lamp flashes until you turn

the power off and on again, or until you set MIDI

Merge to ON. (See page 24.)

u CONTROLLER NUMBER LIST

This shows the controller numbers that can be used with the

ASSIGNABLE Wheel. (See page 22.)

● Note Range of the CBX-K1 (with Octave Shift )

Panel Controls and Terminals

C-2

(0)

C-1

(12)

C0

(24)

C1

(36)

C2

(48)

C3

(60)

C4

(72)

C5

(84)

C6

(96)

C7

(108)

C8

(120)

G8

(127)

Middle C

(C3 or MIDI note number 60)

4 octaves down

3 octaves down

2 octaves down

1 octave down

1 octave up

2 octaves up

3 octaves up

4 octaves up

Normal octave range

(default: when power is turned on)

This section is outside the

“legal” MIDI range and plays

notes Gm4 (80) through C5

(84).

■ Rear Panel

i POWER Switch

Push this switch in to turn on the power. Each time the

power is turned on, the CBX-K1 returns to the default

condition. (See boxed section below.)

o DC IN Terminal

This is for connection to an optional PA-1B or PA-3 AC

power adaptor.

!0 MIDI OUT Terminal

This is for connection to the MIDI IN terminal of another

MIDI device (such as a MIDI tone generator, sequencer or

computer that has a MIDI interface), for sending MIDI

messages to that device. By using the MIDI Merge func-

tion, data received at MIDI IN can be combined with the

data generated by the CBX-K1 and transmitted via this

terminal.

!1 MIDI IN Terminal

This is for connection to the MIDI OUT terminal of another

MIDI device (such as a MIDI keyboard, sequencer or

computer that has a MIDI interface), for input of that

device’s data. By using the MIDI Merge function, that data

can be combined with the data generated by the CBX-K1

and transmitted via the MIDI OUT terminal.

POWER ON> OFF? DC IN INMIDIOUT

Panel Controls and Terminals

The CBX-K1 has no internal memory backup. As a

result, all settings are returned to the factory default

when turning the power off. The basic factory default

settings are listed below.

* MIDI transmit channel: 1

* Octave range: C2-C5

* Transpose: normal (no transposition)

* Fixed velocity: Off (keyboard is velocity sensitive)

* ASSIGNABLE Wheel: Modulation

● User-configurable Defaults:

You can change certain power-on default settings of the

CBX-K1. These include:

* Reversing the PITCH Wheel and ASSIGNABLE

Wheel operation. Hold down N and

turn the power on. (See page 20.)

* Reversing the MSB, LSB order. Hold down

M and turn the power on. (See page

20.)

■ Default Settings of the CBX-K1

!0 !1

Power Supply

Your CBX-K1 will run either from an optional power

adaptor or batteries. Follow the instructions below accord-

ing to the power source you intend to use.

NOTE

■

Before making any connections, make sure that

all equipment to be connected is turned off.

Using a Power Adaptor

Connect one end of the power adaptor (the optional)

Yamaha PA-1B or PA-3) to the DC IN jack on the rear

panel, and the other end to a suitable electrical outlet.

Using Batteries

To use the CBX-K1 on battery power, remove the battery

compartment cover (as shown below) and insert six 1.5V

AA size (SUM-3, R-6 or equivalent) manganese or alkaline

batteries in the battery compartment. Make sure to follow

the polarity indications on the bottom case.

Securely replace the battery compartment cover when done

installing the batteries.

When to Replace the Batteries

When the battery power runs too low to properly operate

the CBX-K1, the V lamp will flash slowly. When

this happens, replace all batteries with a complete set of six

new batteries of the same type.

CAUTION!

■

NEVER mix old and new batteries or

different types of batteries! Also, to prevent possible

damage due to battery leakage, remove the batteries

from the instrument if it is not to be used for an ex-

tended period of time.

IMPORTANT

■

Turning the power off and on again

resets all settings to the factory default, cancelling all

user settings.

CAUTION!

■

Do not attempt to use a power adaptor other than

the PA-1B or PA-3. The use of an incompatible adaptor

may result in irreparable damage to the CBX-K1, and

even pose a serious shock hazard.

■

Be sure to disconnect the power adaptor from the

outlet when the CBX-K1 is not in use.

DC IN

Power adaptor

(PA-1B or PA-3)

Battery compartment cover

OFF (?)

Guided Tour

When using your CBX-K1 for the first time, read through this short section

of the manual. It guides you step-by-step in using many of the basic opera-

tions: setting the instrument up, connecting it properly to other equipment,

and — most importantly — playing it.

Setting Up Your CBX-K1

In this introductory section, you’ll learn how to set up the

CBX-K1 for use in your music system. A variety of setups

are covered here; read through the one that most closely

matches your own setup.

What You’ll Need

Since the CBX-K1 is strictly a MIDI controller and does

not generate any sound by itself, you’ll need other data-

receiving and sound-producing equipment. Basically, you

will need:

* The CBX-K1 and an optional PA-3 or PA-1B AC power

adaptor (or a set of batteries).

* A MIDI device (such as a tone generator, keyboard or

computer) which can receive and play back MIDI data,

and at least one MIDI cable.

* (Optional) An amplifier/speaker system, preferably

stereo, with proper audio connecting cables. Alter-

nately, you can use a set of stereo headphones.

Setup Examples

NOTE

■

The setup examples below show only the MIDI

connections. The audio connections would vary

according to the particular equipment you use. Refer

to the owner’s manuals of your other equipment for

audio connection instructions.

With Computer and Tone Generator

In the small MIDI system below, the CBX-K1 is connected

to a computer and a single tone generator. With the proper

sequencing software on the computer, the CBX-K1 can be

used both for recording performance data to the computer

and playing the sounds of the connected tone generator.

You can also conveniently use the CBX-K1 to start and

stop the sequencer.

For tone generators with a built-in MIDI interface (such as

the Yamaha MU80)

For tone generators without a built-in MIDI interface

MIDI KEYBOARD CBX-K1

MIDI IN

MIDI OUT

MIDI IN

CBX-K1

MIDI

Interface

Computer

Connect the MIDI OUT terminal on the CBX-K1 to the MIDI IN

terminal on the computer’s MIDI interface. The tone generator

should be connected to a MIDI OUT on the interface.

Tone generator

Serial

port

Computer

Tone generator

MU80

Serial

port

MIDI KEYBOARD CBX-K1

MIDI

HOST

MIDI

OUT

HOST SELECT

MIDI Mac

PC-2 PC-1

CBX-K1

Connect the MIDI OUT terminal on the CBX-K1 to the MIDI

IN terminal on the MU80. The MU80 should be connected to

the proper port on the computer. (For complete connection

instructions, refer to the owner’s manual of your particular

tone generator.)

The HOST SELECT switch on the

MU80 allows you to match the type

of computer, when connecting directly

to a computer.

With Sequencer

The CBX-K1 can be used with a stand-alone sequencer, for

recording and editing performance data.

MIDI KEYBOARD CBX-K1

MIDI IN

MIDI OUT

HOST SELECT

MIDI Mac

PC-2 PC-1

MIDI IN

MIDI OUT

Setting Up Your CBX-K1

CBX-K1

Tone generator

MU80

MIDI

keyboard

In a variation of the above setup, set the Clavinova and

CBX-K1 to transmit on the same channel, and set the CBX-

K1’s MIDI Merge function to ON. This lets you play the

tone generator from either keyboard and use the versatile

MIDI functions of the CBX-K1 to control the tone genera-

tor — for example, changing the brightness of the sound in

real time with the ASSIGNABLE Wheel.

NOTE

■

When an external MIDI device is connected to

the MIDI IN of the CBX-K1, the

lamp may

flash, indicating a MIDI error. This is probably due to

a longer-than-normal interval between active sensing

messages received from the device. To remedy this, set

the MIDI Merge of the CBX-K1 to ON. (See page 24.)

Connect the MIDI OUT terminal on the main keyboard to

the MIDI IN terminal on the CBX-K1. Also connect the

MIDI OUT terminal on the CBX-K1 to the MIDI IN terminal

on the tone generator.

With Main Keyboard and Tone Generator

In this system, the CBX-K1 effectively serves as a second

keyboard. The main keyboard (in this case, the Clavinova)

is used to play both its own internal sounds and the sounds

of the connected multi-timbral tone generator on one

channel, while the CBX-K1 is used to play the sounds of

the tone generator on another channel. This lets you play

two sounds at once from the Clavinova, and play a third

sound from the CBX-K1.

With Tone Generator

In the simple system below, the CBX-K1 is used to play the

voices of the MU80 Tone Generator. This setup could also

serve as a simple, yet powerful live performance rig, with

the CBX-K1 being used as a portable, hand-held keyboard.

MIDI KEYBOARD CBX-K1

MIDI

OUT

HOST SELECT

MIDI Mac

PC-2 PC-1

Connect the MIDI OUT terminal on the CBX-K1 to the MIDI

IN terminal on the MU80.

CBX-K1

Tone generator

MU80

MIDI KEYBOARD CBX-K1

MIDI

OUT

QY300

MUSIC SEQUENCER

Sequencer

CBX-K1

Connect the MIDI OUT terminal on the CBX-K1 to the MIDI

IN terminal on the sequencer.

Making the Connections

CAUTION!

■

Before making any connections, make sure

that all equipment to be connected is turned off.

Operation

Connect the MIDI OUT terminal of the CBX-K1 to the MIDI

IN terminal of the tone generator, sequencer or computer

MIDI interface (as shown in the illustrations above).

Make all necessary audio connections, making sure first

that all level controls on those devices are set to the

minimum. (Refer to the owner’s manuals of the devices

you are using for more information on connections.)

Finally, turn on the power of the CBX-K1, then turn on

the power of the connected equipment. (If necessary,

follow the order as recommended in the owner’s manu-

als of the devices you are using.) When turning off the

power, be sure to turn off the CBX-K1 last.

Using the CBX-K1 — Basic Operations

Though the CBX-K1 has many sophisticated functions, it is

very easy to use. All available functions can be controlled

or executed by using the basic operations described in this

section. (For details on individual functions, see pages 18-

22.)

NOTE

■

This introductory section assumes that the

MIDI transmit channel of the CBX-K1 and the MIDI

receive channel of the connected device match. When

the CBX-K1 is turned on, the MIDI transmit channel is

automatically set to 1. For the sake of the following

sections, set the MIDI receive channel of the connected

device to 1 (or Omni).

The illustration below shows how to use the basic real-time controls of the CBX-K1.

Playing the Keyboard and Other Operations

● Changing Voices (Program Change Up/Down)

You can easily step up or down through the voices

(program numbers) on the connected MIDI device.

To do this, hold down C and press

M (to advance one program number), or

press N (to go back one program number).

The LEDs quickly flash on and off when a program

number message is sent. Release C to play the new

voice.

When the CBX-K1 is turned on, the starting point for

program change is 0. This means that when you first

hold down C and press M, program

number 1 will be selected.

NOTE

■

Always release

before playing the

CBX-K1 keyboard. Holding down

accesses

the secondary or “hidden” functions, and you may

inadvertently execute one of these functions by playing

the keyboard while continuing to hold down

NOTE

■

This function does not “wrap around.” In

other words, you cannot go back to program number

127 when at 0, or advance to program number 0 when

at 127.

STOP CONTINUE START

SOUND

OFF

MERGE

ON/OFF 1 2 3 4 5 6

TRANSPOSE

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET

PITCH

ASSIGNABLE

IN MIDI OUT

DRUM

NUMBER

NRPN

CONTROLLER

RPN

FIXED

VELOCITY

MIDI

PROGRAM

CHANGE

BANK

SELECT

TEMPO

PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER

SHIFT

CONTROLLER NUMBER LIST

122 COARSE TUNING

(NRPN)

(RPN)

120 PITCH BEND SENSITIVITY

121 FINE TUNING

123 VIBRATO RATE

124 VIBRATO DEPTH

125 VIBRATO DELAY

126 FILTER CUTOFF FREQUENCY

127 FILTER RESONANCE

128 EG ATTACK TIME

129 EG DECAY TIME

130 EG RELEASE TIME

131 DRUM FILTER CUTOFF FREQUENCY

132 DRUM FILTER RESONANCE

133 DRUM EG ATTACK RATE

74 BRIGHTNESS

84 PORTAMENTO CONTROL

91 REVERB DEPTH

92 TREMOLO DEPTH

93 CHORUS DEPTH

94 VARIATION DEPTH

95 PHASER DEPTH

73 ATTACK TIME

1 MODULATION DEPTH

5 PORTAMENTO TIME

6 DATA ENTRY

7 MAIN VOLUME

8 BALANCE CONTROL

10 PANPOT

CONTROL CHANGE

2 BREATH CONTROL

4 FOOT CONTROL

64 HOLD1(DAMPER)

65 PORTAMENTO

66 SOSTENUTO(CHORD HOLD)

67 SOFT PEDAL

69 HOLD2 (FREEZE)

71 HARMONIC CONTENT

72 RELEASE TIME

11 EXPRESSION

● Changing the Octave Setting

You can easily change the octave range of the CBX-K1

keyboard while playing. In this way the three-octave

keyboard can cover the entire range of MIDI notes, from

C-2 to G8 (0-127).

To shift the keyboard up one octave, press

M. To shift the keyboard down one

octave, press N. When the octave is

changed, the LEDs rapidly flash one, two, three or four

times, according to the selected octave range. For

example, when the setting is changed to two octaves

below normal, the left lamp flashes twice.

Using the CBX-K1 — Basic Operations

NOTE

■

At the lowest and highest octave settings, keys

outside the legal MIDI note range will repeat the center

octave range.

■ Normal octave setting.

OCTAVE

● ASSIGNABLE Wheel

When the CBX-K1 is turned on, this Wheel is set to control

Modulation Depth on the connected MIDI device. It can be

set to control other functions; see page 18 for details. The

Wheel’s maximum/minimum positions can be reversed.

(See page 20.)

● PITCH Wheel

This Wheel controls Pitch Bend on the connected MIDI

device. The Wheel’s maximum/minimum positions can

be reversed. (See page 20.)

Using the SHIFT-Related Functions

The enormous flexibility and power of the CBX-K1 is in its

“hidden” or SHIFT-related functions — allowing you to

send virtually any kind of MIDI message directly from the

keyboard or use the ASSIGNABLE Wheel for real-time

control change.

Many of the functions can be done with one or two key-

strokes, while others require you to enter a number value

and press one of the L keys to execute the function.

All functions can be accessed or executed by using one of

the operations described below.

Holding C, pressing the function’s key and then

L. These functions are indicated with a dashed

underline on the panel (for example, GM ON and XG

ON) and require pressing L to execute.

Holding C, pressing the function’s key, entering

a value and then pressing L. These functions

are indicated with an underline on the panel (for ex-

ample, PROGRAM CHANGE and TEMPO), and

require that a value (Decimal or Hexadecimal) be

entered.

● In using the SHIFT-related functions, re-

member:

Keep holding down C until the end of the

operation. If C is released in mid-operation,

you’ll have to start the operation all over again.

In the instructions that follow, “L” refers to either of

the ENTER keys, J or K.

In other words, this means that either key can be used,

unless indicated otherwise.

NOTE

■

The

lamps flash briefly

when a function is executed or a message is sent.

The MIDI functions can be generally divided into three

types, according to their operation.

Holding C and pressing the function’s key. For

these functions, such as Sequencer Stop and Start,

pressing L is not necessary. These functions are

shown on the panel without underline.

Using the CBX-K1 — Basic Operations

MIDI functions

(Group A and

Group B)

Value entry

(Decimal and

Hexadecimal)

STOP CONTINUE START

SOUND

OFF

MERGE

ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0

TRANSPOSE

HEXA

DECIMAL

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET

ENTER

DRUM

NUMBER

NRPN

CONTROLLER

RPN

FIXED

VELOCITY

MIDI

PROGRAM

CHANGE

BANK

SELECT

TEMPO

PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER

SHIFT

GM

XG

keys

Panel Name Group A Function Group B Function

STOP Stop Song Select

CONTINUE Continue Song Position Pointer

START Start Reset All Controllers

TEMPO Tempo —

BANK SELECT Bank Select —

PROGRAM CHANGE Program Change —

GM ON GM On —

SOUND OFF All Sound Off (each channel) All Sound Off (all channels)

XG ON XG On GM-B Reset

MERGE ON/OFF Merge On/Off (each channel) —

MIDI CH MIDI Channel Merge On/Off (each channel)

FIXED VELOCITY Fixed Velocity Touch Sensitivity

RPN Wheel Assign (RPN)

Controller Direct Data Send

(RPN)

CONTROLLER Wheel Assign

(controller number on panel)

Controller Direct Data Send

(controller number on panel)

NRPN Wheel Assign (NRPN)

Controller Direct Data Send

(NRPN)

DRUM NUMBER Drum Number Device Number

TRANSPOSE Q Transpose Down Wheel Invert

TRANSPOSE W Transpose Up MSB/LSB Invert

● Functions Assigned to the Keyboard

● Entering MSB/LSB Values with K (3 digit

bytes for MSB, 3 digit bytes for LSB; 6 digits total

message). For messages beginning with zeroes, the

first zeroes can be omitted.

Examples:

* 3 → K

: results in a value of MSB = 000, LSB = 003.

* 0 → 3 → K: results in a value of MSB = 000,

LSB = 003.

* 1 → 0 → 0 → 3 → K: results in a value

of MSB = 001, LSB = 003.

* 0 → 1 → 0 → 0 → 3 → K: results in

a value of MSB = 001, LSB = 003.

● Entering MSB/LSB Values with J (2

digit bytes for MSB, 2 digit bytes for LSB; 4 digits total

message). For messages beginning with zeroes, the

first zeroes can be omitted.

Examples:

* 3 → J: results in a value of MSB = 00, LSB =

03.

* 0 → 3 → J: results in a value of MSB = 00,

LSB = 03.

* 1 → 0 → 3 → J: results in a value of

MSB = 01, LSB = 03.

* 0 → 1 → 0 → 3 → J: results in a

value of MSB = 01, LSB = 03.

NOTE

■

The order of MSB and LSB entry can be

reversed. (See page 20.)

NOTES ON THE BASIC OPERATION

■

If you inadvertently press two or more function keys

while performing a function, the last pressed key has

priority.

■

If, after entering a value, you press another function

key before pressing

, the value will be can-

celled.

■

If you enter a value that is outside of a function’s

range, it will be ignored. Legal messages can be one

byte in length (a value from 0-255).

Basic Operations

Selecting Group A and Group B Functions

● Selecting Group A Functions:

Hold down C and press the appropriate key. (See

pages 14 and 18 for specific Group A functions and how

to use them.)

● Selecting Group B Functions:

Hold down C and press K. The

Group B functions are available as long as you continue

to hold down C. (See pages 16 and 20 for

specific Group B functions and how to use them.)

Entering Values

Value entry on the CBX-K1 can be done in two number

systems: Decimal and Hexadecimal. The keys labeled A

through F are for Hexadecimal entry.

● Entering a decimal value:

Hold down C, press the appropriate function key,

enter the desired value in decimal format, then press

● Entering a hexadecimal value:

Hold down C, press the appropriate function key,

enter the desired value in hexadecimal format, then

press J.

Example — Setting the MIDI Transmit Channel to 12:

Decimal:

C + { → 1 → 2 → K

Hexadecimal:

C + { → c → J

Value Entry — Some Specific Examples

and Anomalies

● Using K

Examples:

* 1 → 2 → K: results in a value of 12.

* a → K: results in a value of 10.

* 2 → a → K: results in a value of 210.

* a → 2 → K: results in a value of 102.

* 3 → a → K: results in a value of 310, which is

ignored since it is outside the legal value range (0-255).

Using the CBX-K1 — Basic Operations

Setting the Functions

This section shows by example the operations for the basic

functions.

Using the CBX-K1 — Basic Operations

K. However, when you wish to enter a

decimal value, make sure to press K.

Likewise, when entering a hexadecimal number, make

sure to press J.

STOP CONTINUE START

SOUND

OFF

MERGE

ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0

TRANSPOSE

HEXA

DECIMAL

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET

ENTER

DRUM

NUMBER

NRPN

CONTROLLER

RPN

FIXED

VELOCITY

MIDI

PROGRAM

CHANGE

BANK

SELECT

TEMPO

PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER

SHIFT

GM

XG

Group A Operations

Sending a Simple Command

Operation: C + Function Key

Relevant Functions: Sequencer Stop/Continue/Start; Sound Off

● Example: Sending a Start command to a sequencer or rhythm machine

C + E

You can use the Q and W keys in the same

way, to stop the sequencer or continue playback from the

stopped point.

Setting a Simple Command (on/off)

Operation: C + Function Key

Relevant Functions: Merge On/Off

● Example: Switching the MIDI Merge function of the CBX-K1 on or off

C + P

Sending a Simple Command with L

Operation: C + Function Key → L

Relevant Functions: GM System On; XG System On

Setting a Specific Value for a Function

Operation: C + Function Key → Value → L

Relevant Functions: Tempo; Program Change; MIDI Channel;

Fixed Velocity; Controller; Drum Number; Transpose

Down/Up

● Example: Changing the tempo value on a sequencer or rhythm machine

C + R → 1 → 4 → 0 → K

● Example: Setting a connected tone generator to XG Mode

C + O → L

NOTE

■

Either

key can be used for these

commands.

1 1 5 4 1 2 4 5

8433 4

● Numbers 1 - 8 in the illustration correspond to the operation

numbers below.

* Unless indicated otherwise, L refers to either of

the ENTER keys, J or

Setting a Specific Value for a Function

(MSB, LSB)

Operation: C + Function Key → MSB value → LSB value

→ L

Relevant Functions: Bank Select; RPN; NRPN

● Example: Selecting a Bank of Voices on a Tone Generator

Some tone generators feature two or more banks of voices. This

example shows how to use the Bank Select function to select

different banks. This example also shows you how to use the

functions that require entry of two values: MSB and LSB.

In this example, we’ll enter a value of 012 (MSB) 034 (LSB)

C + T → 0 → 1 → 2 → 0 → 3

→ 4 → K

NOTE

■

Decimal values of MSB and LSB are 3 digits

each (6 digits total); hexadecimal values are 2 digits

each. Zeroes must be entered, unless they occur at the

beginning of the value. For example, for the decimal

value of 001 (MSB) 012 (LSB), the first two zeroes may

be omitted, but the third must be entered. In other

words, the value could be entered as

→

Transpose Setting

Operation: C + G / H

To transpose up one semitone, use the H key

(F3). To transpose down one semitone, use the

G key (E3). Each repeated pressing of the

key while holding C transposes the pitch by an

additional semitone. To restore the normal default trans-

pose setting, hold down C and press both

G / H keys simultaneously.

NOTE

■

You can also enter transpose values directly by

using operation 4 above.

Setting a Specific Value for a Specific

Controller

Operation: C + Function Key → Controller Number →

L → Value(s) → L

Relevant Functions: RPN*; Controller; NRPN*

Functions marked with an asterisk (*) above require that

you enter two values: an MSB (Most Significant Byte)

and an LSB (Least Significant Byte).

● Example: Changing the Portamento Time of a tone generator’s voice

C + S → 5 (Portamento Time) → L →

{2 → 5 → L}

The operation steps enclosed in brackets ({}) can be

repeated or re-entered as long as C is held.

NOTE

■

This operation assigns a controller number for

the ASSIGNABLE Wheel and sends a specific value for

that controller number. You can also send a specific

value for the controller (in the Group B functions)

without altering the controller assignment.

Selecting a Drum Number (when editing

a specific drum number with controller

numbers 131 - 141)

You can use operation 4 above to set the drum number

for editing a specific drum number with controller numbers

131 - 141. However, the following operation lets you set

the Drum number by playing it from the keyboard. This

allows you to hear the drum sound you’ll be editing, since

the last note played on the keyboard determines the drum

sound to be changed.

Without pressing C, find the desired drum number by

sound — by pressing keys on the keyboard. Next, hold

down C, press F, then L. This

sets the drum number to the last key pressed. Then (to set

the controller number for that drum sound), hold down

C and press S, then enter the controller

number (131 through 141). This sets the Controller Num-

ber for the Drum parameter you wish to control with the

ASSIGNABLE Wheel.

Using the CBX-K1 — Basic Operations

Group B function names are not shown on the panel. For

the list and explanations of Group B functions, refer to

pages 12 and 20.

119

● Example: Sending a Reset All Controllers command to a sequencer or

tone generator

C + K → E (Reset All Controllers)

Setting a Simple Command (on/off)

Operation: C + K → Function Key → Value

Relevant Function: Merge On/Off (each channel)

● Example: Setting a connected tone generator to GM-B Reset

C + K → O (GM-B Reset) → L

Setting a Specific Value for a Function

Operation: C + K → Function Key →

Value → L

Relevant Functions: Song Select; Touch Sensitivity; Device

Number

Sending a Simple Command with L

Operation: C + K → Function Key →

Relevant Function: GM-B Reset

Sending a Simple Command

Operation: C + K → Function Key

Relevant Functions: Reset All Controllers; Sound Off (all

channels); Wheel Invert; MSB/LSB Invert

● Example: Switching the MIDI Merge function of the CBX-K1 on or off for

MIDI channel 12

C + K → { (Merge On/Off for each

channel) → c (for MIDI channel 12)

Keys 1 - f and 0 correspond to MIDI channel 1-

15 and 16, respectively. Pressing each key toggles the on/

off status of each channel.

● Example: Changing the touch sensitivity of the CBX-K1 to 10

C + K → } (Touch Sensitivity) →

1 → 0 → L

● Numbers 9 -

in the illustration correspond to the

operation numbers below.

Group B Operations

STOP CONTINUE START

SOUND

OFF

MERGE

ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0

TRANSPOSE

HEXA

DECIMAL

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET

ENTER

DRUM

NUMBER

NRPN

CONTROLLER

RPN

FIXED

VELOCITY

MIDI

PROGRAM

CHANGE

BANK

SELECT

TEMPO

PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER

SHIFT

GM

XG

9 99 9

12 12 14 14

121413 11 10

* Unless indicated otherwise, L refers to either of

the ENTER keys, J or

K. However, when you wish to enter a

decimal value, make sure to press K.

Likewise, when entering a hexadecimal number, make

sure to press J.

La pagina si sta caricando...

Yamaha CBX-K1 Manuale del proprietario

Marca: Yamaha

Modello: CBX-K1

Categoria: Strumenti musicali

Tipo: Manuale del proprietario

Scarica PDF

rapporto

in altre lingue

English: Yamaha CBX-K1 Owner's manual
français: Yamaha CBX-K1 Le manuel du propriétaire
español: Yamaha CBX-K1 El manual del propietario
Deutsch: Yamaha CBX-K1 Bedienungsanleitung
русский: Yamaha CBX-K1 Инструкция по применению
Nederlands: Yamaha CBX-K1 de handleiding
português: Yamaha CBX-K1 Manual do proprietário
dansk: Yamaha CBX-K1 Brugervejledning
čeština: Yamaha CBX-K1 Návod k obsluze
polski: Yamaha CBX-K1 Instrukcja obsługi
svenska: Yamaha CBX-K1 Bruksanvisning
Türkçe: Yamaha CBX-K1 El kitabı
suomi: Yamaha CBX-K1 Omistajan opas
română: Yamaha CBX-K1 Manualul proprietarului

Yamaha CBX-K1 Manuale del proprietario

Yamaha CBX-K1 Manuale del proprietario

in altre lingue

Documenti correlati