Yamaha CBX-K1 Manuale del proprietario

Categoria
Strumenti musicali
Tipo
Manuale del proprietario
M.D.G., EMI Division © Yamaha Corporation 1995
VT05800 502PTCP18.2-01A0 Printed in Japan
FCC INFORMATION (U.S.A.)
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
IMPORTANT:
When connecting this product to accessories and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC authorization to use this product in the USA.
NOTE:
This product has been tested and found to comply with the requirements listed in FCC Regula-
tions, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential environment will not result in
harmful interference with other electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in the user’s manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations
does not guarantee that interference will not occur in all installations. If this product is found to be
the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC
line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is
300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate, please contact
Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park
CA, 90620
This applies only to products distributed by Yamaha Corporation of America.
CANADA
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE
EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION
OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT
LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES
DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE
DES COMMUNICATIONS DU CANADA.
* This applies only to products distributed by Yamaha Canada Music LTD.
* Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Music LTD.
Dit produkt is gefabriceerd in overeenstemming met
de radiostoringsvoorschriften van de Richtlijn van de
Raad (82/499/EEG).
ΑΥΤΗ Η ΣΥΣΚΕΥΗ ΑΝΤΑΠΟΚΡΙΝΕΤΑΙ ΣΤΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΤΩΝ Ο∆ΗΓΙΩΝ ΤΗΣ ΕΥΡΩΠΑΙΚΗΣ
ΟΙΚΟΝΟΜΙΚΗΣ ΚΟΙΝΟΤΗΤΑΣ 82/499/Ε.Ο.Κ.
Este produto está de acordo com o radio de
interferencia frequente requiridos do Conselho
Diretivo 82/499/EEC.
Dette apparat overholder det gaeldende EF-direktiv
verdrørende radiostøj.
Cet appareil est conforme aux prescriptions de la
directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/
EWG und/oder 87/308/EWG.
This product complies with the radio frequency
interference requirements of the Council Directive 82/
499/EEC and/or 87/308/EEC.
Questo apparecchio è conforme al D.M.13 aprile 1989
(Direttiva CEE/87/308) sulla soppressione dei
radiodisturbi.
Este producto está de acuerdo con los requisitos sobre
interferencias de radio frequencia fijados por el
Consejo Directivo 87/308/CEE.
YAMAHA CORPORATION
Model CBX-K1
Serial No.
Purchase Date
SPECIAL MESSAGE SECTION (U.S.A.)
This product utilizes batteries or an external power
supply (adapter). DO NOT connect this product to
any power supply or adapter other than one
described in the manual, on the name plate, or
specifically recommended by Yamaha.
This product should be used only with the compo-
nents supplied or; a cart, rack, or stand that is
recommended by Yamaha. If a cart, etc., is used,
please observe all safety markings and instruc-
tions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is be-
lieved to be correct at the time of printing. How-
ever, Yamaha reserves the right to change or
modify any of the specifications without notice or
obligation to update existing units.
This product, either alone or in combination with
an amplifier and headphones or speaker/s, may be
capable of producing sound levels that could
cause permanent hearing loss. DO NOT operate
for long periods of time at a high volume level or
at a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
consult an audiologist. IMPORTANT: The louder
the sound, the shorter the time period before
damage occurs.
NOTICE:
Service charges incurred due to lack of knowledge
relating to how a function or effect works (when
the unit is operating as designed) are not covered
by the manufacturer’s warranty, and are therefore
the owners responsibility. Please study this
manual carefully and consult your dealer before
requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both
user safe and environmentally friendly. We sin-
cerely believe that our products and the produc-
tion methods used to produce them, meet these
goals. In keeping with both the letter and the spirit
of the law, we want you to be aware of the follow-
ing:
Battery Notice:
This product MAY contain a small non-recharge-
able battery which (if applicable) is soldered in
place. The average life span of this type of battery
is approximately five years. When replacement
becomes necessary, contact a qualified service
representative to perform the replacement.
This product may also use “household” type bat-
teries. Some of these may be rechargeable. Make
sure that the battery being charged is a recharge-
able type and that the charger is intended for the
battery being charged.
When installing batteries, do not mix old batteries
with new, or with batteries of a different type.
Batteries MUST be installed correctly. Mismatches
or incorrect installation may result in overheating
and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any
battery. Keep all batteries away from children.
Dispose of used batteries promptly and as regu-
lated by the laws in your area. Note: Check with
any retailer of household type batteries in your
area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond
repair, or for some reason its useful life is consid-
ered to be at an end, please observe all local,
state, and federal regulations that relate to the
disposal of products that contain lead, batteries,
plastics, etc. If your dealer is unable to assist you,
please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the
product. The model number, serial number, power
requirements, etc., are located on this plate. You
should record the model number, serial number,
and the date of purchase in the spaces provided
below and retain this manual as a permanent
record of your purchase.
92-BP
PLEASE KEEP THIS MANUAL
Welcome to the CBX-K1
Congratulations and thank you for purchasing the Yamaha CBX-K1 MIDI Keyboard!
The CBX-K1 is a sophisticated, yet compact MIDI keyboard controller, for use with
computers and MIDI music systems. It allows you to play connected tone generators
and rhythm machines, and enter performance data to sequencers and computers. It
features a sophisticated touch-sensitive keyboard that can be adjusted to cover the full
128-note MIDI range. It also provides a wealth of MIDI controls that allow you to
send virtually any MIDI message directly from the keyboard. Moreover, the CBX-K1
has a versatile ASSIGNABLE Wheel that lets you control a wide variety of parameters
on your connected tone generator or sequencer in real time. Because of its exceptionally
portable size, convenient battery/AC adaptor power supply, compatibility with Gen-
eral MIDI (GM) and XG, and extraordinarily powerful and comprehensive MIDI
control functions, the CBX-K1 is an invaluable tool a MIDI Swiss army knife, of sorts
for all MIDI musicians and performers.
IMPORTANT
The CBX-K1 does not contain an internal tone generator. In order to
play sounds from the CBX-K1, you need an external tone generator, such as the
Yamaha MU series or TG series tone generators.
NOTE
The many MIDI functions and features of the CBX-K1 may not be supported
by your particular MIDI device. Be sure to refer to the owners manual of your par-
ticular MIDI device when using it with the CBX-K1.
Table of Contents
The CBX-K1 — What It Is and What It Can Do . . . . . . 1
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Panel Controls and Terminals . . . . . . . . . . . . . . . . . 4
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Note Range of the CBX-K1 . . . . . . . . . . . . . 5
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Default Settings of the CBX-K1 . . . . . . . . . . 6
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using a Power Adaptor . . . . . . . . . . . . . . . . . . . . 7
Using Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
When to Replace the Batteries . . . . . . . . . . . . . . . 7
Guided Tour
Setting Up Your CBX-K1 . . . . . . . . . . . . . . . . . . . . . 8
What You’ll Need . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Making the Connections . . . . . . . . . . . . . . . . . . . . . . 9
Using the CBX-K1 Basic Operations . . . . . . . . . . 10
Playing the Keyboard and Other Operations . . . . . 10
Using the SHIFT-Related Functions . . . . . . . . . . . . 12
Basic Operations . . . . . . . . . . . . . . . . . . . . 13
Setting the Functions . . . . . . . . . . . . . . . . . . . . . . . 14
Group A Operations . . . . . . . . . . . . . . . . . . 14
Group B Operations . . . . . . . . . . . . . . . . . . 16
Reference
Group A Functions . . . . . . . . . . . . . . . . . . . . . . . . 18
Group B Functions . . . . . . . . . . . . . . . . . . . . . . . . 20
ASSIGNABLE Wheel — Controller Number List . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . 24
MIDI Implementation Chart . . . . . . . . . . . . . . . . . . 26
1
The CBX-K1 — What It Is and What It Can Do
What It Is
The CBX-K1 is a compact, highly portable 37-key MIDI
keyboard, designed especially for use with computers and
MIDI music systems. The CBX-K1 does not generate any
sound itself, but can be used as a keyboard controller for
playing sounds on a connected tone generator or rhythm
machine. It’s also ideal for recording to sequencers and
computers. The keyboard is touch-sensitive and its octave
range can be changed to cover the full 128-note MIDI
range.
The true power and flexibility of the CBX-K1 is in its
comprehensive MIDI controls. The CBX-K1 allows you to
send virtually any type of MIDI message to connected
MIDI devices. Pre-programmed commands provide easy
control of basic sequencer/rhythm machine functions such
as Start, Stop, Tempo and Song Select, while comprehen-
sive program change commands let you easily select
program banks and voices.
Most importantly, though, the CBX-K1 has an ASSIGN-
ABLE Wheel that can be set for control of any controller
number. This means that you can use the ASSIGNABLE
Wheel to control a wide variety of parameters on your
connected tone generator — such as Volume, Pan, Bright-
ness, and the Depth of various effects — in real time. This
gives you expressive control over different aspects of the
sound in live performance.
The CBX-K1 is also the latest instrument in the Yamaha
line to support the XG format, a new addition to the
General MIDI standard. In short, XG provides for more
instrument sounds and variations, and greater expressive
control over voices and effects. With the use of the
ASSIGNABLE Wheel on the CBX-K1, you have direct
real-time control over many of these newly supported
functions and parameters.
What It Can Do
Here are a few application ideas on how you can use the
CBX-K1. The list below is not comprehensive, but is
meant to be a general guide to the possibilities and provide
a starting point or springboard for your own creative ideas
and explorations.
Using With a MIDI Tone Generator
In one of the most basic setups, you can play a connected
tone generator from the CBX-K1. Because it’s so compact
and portable, you can even use it as a hand-held keyboard
for live performance.
Using as a Second Keyboard or Dedicated
MIDI Controller
The CBX-K1 is small enough to fit on top of nearly any
keyboard, making it perfect as a second keyboard. Since
the CBX-K1 has a MIDI IN terminal, you can connect it
between your main keyboard and your tone generator, and
use the extensive MIDI capabilities of the CBX-K1 for
greater expressive control during your performance.
Using in a MIDI Music System
Combined with a laptop computer and a compact tone
generator (like the General MIDI/XG-compatible Yamaha
MU80), the CBX-K1 gives you comprehensive music
making power — for recording, composing, arranging,
practicing, and editing — in a portable system that’s ready
to go wherever you go. The CBX-K1 is an ideal addition
to larger MIDI studios as well, since it provides far greater
MIDI control and flexibility than nearly any other keyboard
controller. Use it along side your main MIDI keyboard as a
kind of MIDI Swiss army knife — sending necessary MIDI
messages, working the real-time controllers, or editing
already recorded sequencer tracks.
Multimedia
Since it’s portable and compatible with the General MIDI
and XG formats, the CBX-K1 is a natural for multimedia
applications. Because of its ease of use and comprehensive
functions, it’s the only keyboard you’ll ever need for
recording and editing MIDI data on your multimedia
creations.
2
ELECTROMAGNETIC INTERFERENCE
Avoid using the unit near televisions, radios or other
equipment generating electromagnetic fields. Proximity to
such equipment may cause the unit to malfunction, and may
generate interference noise in the other appliance as well.
DO NOT OPEN THE CASE OR TRY REPAIRING
THE INSTRUMENT YOURSELF
The instrument contains no user-serviceable parts. Never
open the case or tamper with the internal circuitry in any
way, since doing so may result in damage to the instrument.
Refer all servicing to qualified Yamaha service personnel.
MIDI CABLES
When connecting the instrument to other MIDI equipment,
be sure to use only high-quality cables made especially for
MIDI data transmission. Also, avoid using cables longer
than 15 meters, since long cables can result in data errors.
Precautions
Your CBX-K1 will give you years of reliable service if you
follow the simple precautions below:
LOCATION
Keep the instrument away from locations where it is likely
to be exposed to high temperatures (such as direct sunlight)
or humidity. Also avoid locations which are subject to
excessive dust accumulation or vibration which could
damage the instrument.
USE THE CORRECT POWER ADAPTOR
Use only the recommended PA-1B or PA-3 Power Adaptor
for supplying power. Use of another adaptor may cause
serious damage to the instrument or the adaptor itself. Also
avoid using a multiple-plug adaptor; plug the adaptor
directly into a wall outlet.
MAKE SURE POWER IS OFF WHEN MAKING
OR REMOVING CONNECTIONS
To prevent damage to the instrument and other connected
equipment, always turn off the power prior to connecting or
disconnecting cables. Also, turn the power off when the
instrument is not in use, and disconnect the power adaptor
during electric storms.
NO MEMORY BACKUP
The CBX-K1 has no internal memory backup. As a result,
all settings are returned to the factory default when turning
the power off.
HANDLE THE INSTRUMENT WITH CARE
Although the instrument has been constructed to withstand
the rigors of normal use for optimum sturdiness and
reliability, avoid subjecting it to strong physical shocks
(such as dropping or hitting it). Since the CBX-K1 is a
precision-made electronic device, also avoid applying
excessive force to the various controls. When moving the
instrument, first unplug the power adaptor and all other
cables to prevent damage to cords and jacks. Always
unplug cables by gripping the plug firmly, not by pulling
on the cable.
CLEAN WITH A SOFT, DRY CLOTH
Never use solvents such as benzine or thinner to clean the
instrument, since these will damage the cabinet finish or
dull the keys. Wipe clean with a soft, dry cloth. If neces-
sary, use a soft, clean, slightly moistened cloth — making
sure to wipe the instrument off again with a dry cloth. Do
not leave vinyl on the panel as this may stick to and
discolor the surface.
Yamaha is not responsible for damage caused by
improper handling or operation.
3
By and large, the CBX-K1 is very easy to use and this manual is self-explanatory. However, we strongly recommend that you
take time to read the manual — especially before trying some of the more sophisticated MIDI functions. Read through all of
the initial sections first, then go on to the “Guided Tour” to set up your CBX-K1, learn how to use its various functions, and
try out some of the practical application examples to help you become more familiar with its operations. For those who need
to delve deeper, the “Reference” section provides at-a-glance information and important details on all functions.
The following conventions are used throughout this manual:
* Panel buttons and controls are indicated as they appear on the actual instrument. (For example, C and
M.
* The functions and features assigned to the keyboard are shown like this: T and {.
* Unless indicated otherwise, L refers to either of the ENTER keys, J or K.
However, when you wish to enter a decimal value, make sure to press K. Likewise, when entering a
hexadecimal number, make sure to press J.
* Actual MIDI data messages (in hexadecimal) are indicated as follows: <<FE>> and <<En 00 40>>, etc.
* Operation steps are indicated as follows:
Example Actual Operation
C + E While holding down the C button, press E (D2).
C + U L While holding down the C button, first press U (Fm2), then press
L (either J or K).
How to Use This Manual
Specifications
Keyboard
37 mini key keyboard (C2-C5), velocity responsive
Functions
Basic: Octave Shift (+/- 4 octaves), Pitch Bend, Assignable
control, MIDI Merge (MIDI IN)
MIDI Data: Sequencer control, MIDI clock, Bank Select,
Program Change, GM System On, XG System On,
GM-B Reset, Control Change, All Sound Off, Reset All
Controllers, and others
Assignable Parameters: Transpose (+/- 12 semitones), MIDI
Transmit Channel, Fixed Velocity, Touch Sensitivity,
Device Number, Merge On/Off (each channel)
Panel Controls and Indicators
SHIFT button, OCTAVE SHIFT Q/W buttons and lamps,
PITCH Wheel, ASSIGNABLE Wheel, POWER ON/OFF switch
Input/Output Terminals
MIDI IN, MIDI OUT, DC IN
Power Supply
Yamaha PA-3 or PA-1B AC Power Adaptor (sold separately),
or six “AA” size, SUM-3, R-6 or equivalent batteries (sold
separately).
Power Consumption
Approximately 35 mA (with battery use); approximately 2 W
(with AC adaptor use).
Dimensions (W x D x H)
509 x 155 x 55 mm (20-1/16” x 6-1/8” x 2-3/16”)
Weight (without batteries)
1.3 kg (2 lbs., 14 oz.)
4
Panel Controls and Terminals
Front Panel
q Keyboard
The CBX-K1 has a 37-key, 3-octave keyboard (C2 to C5),
featuring initial touch (velocity) control. All note on, note
off and velocity data is transmitted via the MIDI OUT
terminal. When used with the C button, the keys are
used for changing various settings and sending special
MIDI messages. (See page 12.)
About the Functions of the CBX-K1: The functions are
divided into two groups: Group A and Group B. The
Group A functions are shown on the panel, above the
left section of the keyboard. The Group B functions are
“hidden” and are listed on pages 12 and 20. Several
functions can be used by pressing only the relevant key;
in other words, pressing L is not necessary. These
functions, such as Sequencer Stop and Start, are shown
on the panel without underline. The right section of the
keyboard serves as value entry and is used for those
functions whose names are underlined on the panel and
require value entry, such as Program Change and
Tempo. Functions whose names appear with a dashed
underline on the panel (for example, GM ON and XG
ON) require pressing L. Value entry on the CBX-
K1 can be done in two number systems: Decimal and
Hexadecimal. The keys labeled A through F are for
Hexadecimal entry.
NOTE
The normal (default) velocity range of the
CBX-K1 is from 16 to 127. The range differs accord-
ing to the Touch Sensitivity setting (see page 20).
w PITCH Wheel (Pitch Bend)
This spring-loaded Wheel controls Pitch Bend. The
Wheel’s operation can be reversed. (See page 20.)
e ASSIGNABLE Wheel
When the CBX-K1 is turned on, this Wheel (with center
detent) is set to control Modulation Depth on the connected
MIDI device. It can be set to control other functions; see
pages 18 and 22 for details. The Wheel’s operation can be
reversed. (See page 20.)
r C Button
This button is used to access the “hidden” functions of the
CBX-K1. Used with the N /
M buttons, it allows you to step up or down
through program numbers. (See page 10.) Used with the
keys of the keyboard, it allows you to access the sophisti-
cated MIDI control functions. (See page 12.)
t N / M Buttons
These buttons are used to change the octave range of the
keyboard, allowing you to play across the entire range of
MIDI notes (C-2 to G8). (See page 5.) Press both of these
buttons together to restore the normal octave setting (C2 to
C5). With the C button, these buttons can also be
used to step up or down through program numbers on the
connected MIDI device. (See page 10.)
STOP CONTINUE START
SOUND
OFF
MERGE
ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0
TRANSPOSE
HEXA
DECIMAL
DECIMAL
DC IN
OCTAVE
OCTAVE SHIFT
OCTAVE
RESET
PITCH
ASSIGNABLE
IN MIDI OUT
ENTER
DRUM
NUMBER
NRPN
CONTROLLER
RPN
FIXED
VELOCITY
MIDI
CH
PROGRAM
CHANGE
BANK
SELECT
TEMPO
PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER
POWER ON OFF
SHIFT
GM
ON
XG
ON
MIDI KEYBOARD CBX-K1
CONTROLLER NUMBER LIST
122 COARSE TUNING
(NRPN)
(RPN)
120 PITCH BEND SENSITIVITY
121 FINE TUNING
123 VIBRATO RATE
124 VIBRATO DEPTH
125 VIBRATO DELAY
126 FILTER CUTOFF FREQUENCY
127 FILTER RESONANCE
128 EG ATTACK TIME
129 EG DECAY TIME
130 EG RELEASE TIME
131 DRUM FILTER CUTOFF FREQUENCY
132 DRUM FILTER RESONANCE
133 DRUM EG ATTACK RATE
134 DRUM EG DECAY RATE
135 DRUM PITCH COARSE
136 DRUM PITCH FINE
137 DRUM LEVEL
138 DRUM PAN
139 DRUM REVERB DEPTH
140 DRUM CHORUS DEPTH
141 DRUM VARIATION DEPTH
142 CHANNEL PRESSURE
143 POLYPHONIC KEY PRESSURE
144 MASTER VOLUME
145 MASTER BALANCE
146 MASTER TUNING
147 VELOCITY
148 TEMPO
OTHERS
74 BRIGHTNESS
84 PORTAMENTO CONTROL
91 REVERB DEPTH
92 TREMOLO DEPTH
93 CHORUS DEPTH
94 VARIATION DEPTH
95 PHASER DEPTH
73 ATTACK TIME
1 MODULATION DEPTH
5 PORTAMENTO TIME
6 DATA ENTRY
7 MAIN VOLUME
8 BALANCE CONTROL
10 PANPOT
CONTROL CHANGE
2 BREATH CONTROL
4 FOOT CONTROL
64 HOLD1(DAMPER)
65 PORTAMENTO
66 SOSTENUTO(CHORD HOLD)
67 SOFT PEDAL
69 HOLD2 (FREEZE)
71 HARMONIC CONTENT
72 RELEASE TIME
11 EXPRESSION
q
uw e
r
y
t
5
y V / B Lamps
These lamps provide several indications:
* During normal playing conditions, these indicate the
octave setting of the keyboard, up (B) or down
(V). Both light together for the normal octave
setting. When changing the octave setting, these flash
to indicate the number of octaves, up or down. (See
page 11.)
* When using some of the “hidden” functions, these flash
when a MIDI message is transmitted or when a function
is executed.
* The left lamp flashes slowly when the battery power is
too low for proper operation.
* The right lamp flashes quickly when there is some kind
of MIDI receive error. The lamp flashes until you turn
the power off and on again, or until you set MIDI
Merge to ON. (See page 24.)
u CONTROLLER NUMBER LIST
This shows the controller numbers that can be used with the
ASSIGNABLE Wheel. (See page 22.)
Note Range of the CBX-K1 (with Octave Shift )
Panel Controls and Terminals
C-2
(0)
C-1
(12)
C0
(24)
C1
(36)
C2
(48)
C3
(60)
C4
(72)
C5
(84)
C6
(96)
C7
(108)
C8
(120)
G8
(127)
Middle C
(C3 or MIDI note number 60)
4 octaves down
3 octaves down
2 octaves down
1 octave down
1 octave up
2 octaves up
3 octaves up
4 octaves up
Normal octave range
(default: when power is turned on)
This section is outside the
“legal” MIDI range and plays
notes Gm4 (80) through C5
(84).
6
Rear Panel
i POWER Switch
Push this switch in to turn on the power. Each time the
power is turned on, the CBX-K1 returns to the default
condition. (See boxed section below.)
o DC IN Terminal
This is for connection to an optional PA-1B or PA-3 AC
power adaptor.
!0 MIDI OUT Terminal
This is for connection to the MIDI IN terminal of another
MIDI device (such as a MIDI tone generator, sequencer or
computer that has a MIDI interface), for sending MIDI
messages to that device. By using the MIDI Merge func-
tion, data received at MIDI IN can be combined with the
data generated by the CBX-K1 and transmitted via this
terminal.
!1 MIDI IN Terminal
This is for connection to the MIDI OUT terminal of another
MIDI device (such as a MIDI keyboard, sequencer or
computer that has a MIDI interface), for input of that
device’s data. By using the MIDI Merge function, that data
can be combined with the data generated by the CBX-K1
and transmitted via the MIDI OUT terminal.
oi
POWER ON> OFF? DC IN INMIDIOUT
Panel Controls and Terminals
The CBX-K1 has no internal memory backup. As a
result, all settings are returned to the factory default
when turning the power off. The basic factory default
settings are listed below.
* MIDI transmit channel: 1
* Octave range: C2-C5
* Transpose: normal (no transposition)
* Fixed velocity: Off (keyboard is velocity sensitive)
* ASSIGNABLE Wheel: Modulation
User-configurable Defaults:
You can change certain power-on default settings of the
CBX-K1. These include:
* Reversing the PITCH Wheel and ASSIGNABLE
Wheel operation. Hold down N and
turn the power on. (See page 20.)
* Reversing the MSB, LSB order. Hold down
M and turn the power on. (See page
20.)
Default Settings of the CBX-K1
!0 !1
7
Power Supply
Your CBX-K1 will run either from an optional power
adaptor or batteries. Follow the instructions below accord-
ing to the power source you intend to use.
NOTE
Before making any connections, make sure that
all equipment to be connected is turned off.
Using a Power Adaptor
Connect one end of the power adaptor (the optional)
Yamaha PA-1B or PA-3) to the DC IN jack on the rear
panel, and the other end to a suitable electrical outlet.
Using Batteries
To use the CBX-K1 on battery power, remove the battery
compartment cover (as shown below) and insert six 1.5V
AA size (SUM-3, R-6 or equivalent) manganese or alkaline
batteries in the battery compartment. Make sure to follow
the polarity indications on the bottom case.
Securely replace the battery compartment cover when done
installing the batteries.
When to Replace the Batteries
When the battery power runs too low to properly operate
the CBX-K1, the V lamp will flash slowly. When
this happens, replace all batteries with a complete set of six
new batteries of the same type.
CAUTION!
NEVER mix old and new batteries or
different types of batteries! Also, to prevent possible
damage due to battery leakage, remove the batteries
from the instrument if it is not to be used for an ex-
tended period of time.
IMPORTANT
Turning the power off and on again
resets all settings to the factory default, cancelling all
user settings.
CAUTION!
Do not attempt to use a power adaptor other than
the PA-1B or PA-3. The use of an incompatible adaptor
may result in irreparable damage to the CBX-K1, and
even pose a serious shock hazard.
Be sure to disconnect the power adaptor from the
outlet when the CBX-K1 is not in use.
DC IN
Power adaptor
(PA-1B or PA-3)
Battery compartment cover
OFF (?)
8
Guided Tour
When using your CBX-K1 for the first time, read through this short section
of the manual. It guides you step-by-step in using many of the basic opera-
tions: setting the instrument up, connecting it properly to other equipment,
and — most importantly — playing it.
Setting Up Your CBX-K1
In this introductory section, you’ll learn how to set up the
CBX-K1 for use in your music system. A variety of setups
are covered here; read through the one that most closely
matches your own setup.
What You’ll Need
Since the CBX-K1 is strictly a MIDI controller and does
not generate any sound by itself, you’ll need other data-
receiving and sound-producing equipment. Basically, you
will need:
* The CBX-K1 and an optional PA-3 or PA-1B AC power
adaptor (or a set of batteries).
* A MIDI device (such as a tone generator, keyboard or
computer) which can receive and play back MIDI data,
and at least one MIDI cable.
* (Optional) An amplifier/speaker system, preferably
stereo, with proper audio connecting cables. Alter-
nately, you can use a set of stereo headphones.
Setup Examples
NOTE
The setup examples below show only the MIDI
connections. The audio connections would vary
according to the particular equipment you use. Refer
to the owners manuals of your other equipment for
audio connection instructions.
With Computer and Tone Generator
In the small MIDI system below, the CBX-K1 is connected
to a computer and a single tone generator. With the proper
sequencing software on the computer, the CBX-K1 can be
used both for recording performance data to the computer
and playing the sounds of the connected tone generator.
You can also conveniently use the CBX-K1 to start and
stop the sequencer.
For tone generators with a built-in MIDI interface (such as
the Yamaha MU80)
For tone generators without a built-in MIDI interface
MIDI KEYBOARD CBX-K1
MIDI IN
MIDI OUT
MIDI OUT
MIDI IN
CBX-K1
MIDI
Interface
Computer
Connect the MIDI OUT terminal on the CBX-K1 to the MIDI IN
terminal on the computer’s MIDI interface. The tone generator
should be connected to a MIDI OUT on the interface.
Tone generator
Serial
port
Computer
Tone generator
MU80
Serial
port
MIDI KEYBOARD CBX-K1
MIDI
IN
TO
HOST
MIDI
OUT
HOST SELECT
MIDI Mac
PC-2 PC-1
CBX-K1
Connect the MIDI OUT terminal on the CBX-K1 to the MIDI
IN terminal on the MU80. The MU80 should be connected to
the proper port on the computer. (For complete connection
instructions, refer to the owner’s manual of your particular
tone generator.)
The HOST SELECT switch on the
MU80 allows you to match the type
of computer, when connecting directly
to a computer.
With Sequencer
The CBX-K1 can be used with a stand-alone sequencer, for
recording and editing performance data.
9
MIDI KEYBOARD CBX-K1
MIDI IN
MIDI OUT
HOST SELECT
MIDI Mac
PC-2 PC-1
MIDI IN
MIDI OUT
Setting Up Your CBX-K1
CBX-K1
Tone generator
MU80
MIDI
keyboard
In a variation of the above setup, set the Clavinova and
CBX-K1 to transmit on the same channel, and set the CBX-
K1’s MIDI Merge function to ON. This lets you play the
tone generator from either keyboard and use the versatile
MIDI functions of the CBX-K1 to control the tone genera-
tor — for example, changing the brightness of the sound in
real time with the ASSIGNABLE Wheel.
NOTE
When an external MIDI device is connected to
the MIDI IN of the CBX-K1, the
B
lamp may
flash, indicating a MIDI error. This is probably due to
a longer-than-normal interval between active sensing
messages received from the device. To remedy this, set
the MIDI Merge of the CBX-K1 to ON. (See page 24.)
Connect the MIDI OUT terminal on the main keyboard to
the MIDI IN terminal on the CBX-K1. Also connect the
MIDI OUT terminal on the CBX-K1 to the MIDI IN terminal
on the tone generator.
With Main Keyboard and Tone Generator
In this system, the CBX-K1 effectively serves as a second
keyboard. The main keyboard (in this case, the Clavinova)
is used to play both its own internal sounds and the sounds
of the connected multi-timbral tone generator on one
channel, while the CBX-K1 is used to play the sounds of
the tone generator on another channel. This lets you play
two sounds at once from the Clavinova, and play a third
sound from the CBX-K1.
With Tone Generator
In the simple system below, the CBX-K1 is used to play the
voices of the MU80 Tone Generator. This setup could also
serve as a simple, yet powerful live performance rig, with
the CBX-K1 being used as a portable, hand-held keyboard.
MIDI KEYBOARD CBX-K1
MIDI
IN
MIDI
OUT
HOST SELECT
MIDI Mac
PC-2 PC-1
Connect the MIDI OUT terminal on the CBX-K1 to the MIDI
IN terminal on the MU80.
CBX-K1
Tone generator
MU80
MIDI KEYBOARD CBX-K1
MIDI
IN
MIDI
OUT
QY300
MUSIC SEQUENCER
Sequencer
CBX-K1
Connect the MIDI OUT terminal on the CBX-K1 to the MIDI
IN terminal on the sequencer.
Making the Connections
CAUTION!
Before making any connections, make sure
that all equipment to be connected is turned off.
Operation
1.
Connect the MIDI OUT terminal of the CBX-K1 to the MIDI
IN terminal of the tone generator, sequencer or computer
MIDI interface (as shown in the illustrations above).
2.
Make all necessary audio connections, making sure first
that all level controls on those devices are set to the
minimum. (Refer to the owners manuals of the devices
you are using for more information on connections.)
3.
Finally, turn on the power of the CBX-K1, then turn on
the power of the connected equipment. (If necessary,
follow the order as recommended in the owners manu-
als of the devices you are using.) When turning off the
power, be sure to turn off the CBX-K1 last.
10
Using the CBX-K1 — Basic Operations
Though the CBX-K1 has many sophisticated functions, it is
very easy to use. All available functions can be controlled
or executed by using the basic operations described in this
section. (For details on individual functions, see pages 18-
22.)
NOTE
This introductory section assumes that the
MIDI transmit channel of the CBX-K1 and the MIDI
receive channel of the connected device match. When
the CBX-K1 is turned on, the MIDI transmit channel is
automatically set to 1. For the sake of the following
sections, set the MIDI receive channel of the connected
device to 1 (or Omni).
The illustration below shows how to use the basic real-time controls of the CBX-K1.
Playing the Keyboard and Other Operations
Changing Voices (Program Change Up/Down)
You can easily step up or down through the voices
(program numbers) on the connected MIDI device.
To do this, hold down C and press
M (to advance one program number), or
press N (to go back one program number).
The LEDs quickly flash on and off when a program
number message is sent. Release C to play the new
voice.
When the CBX-K1 is turned on, the starting point for
program change is 0. This means that when you first
hold down C and press M, program
number 1 will be selected.
NOTE
Always release
C
before playing the
CBX-K1 keyboard. Holding down
C
accesses
the secondary or “hidden” functions, and you may
inadvertently execute one of these functions by playing
the keyboard while continuing to hold down
C
.
NOTE
This function does not “wrap around.” In
other words, you cannot go back to program number
127 when at 0, or advance to program number 0 when
at 127.
11
STOP CONTINUE START
SOUND
OFF
MERGE
ON/OFF 1 2 3 4 5 6
TRANSPOSE
OCTAVE
OCTAVE SHIFT
OCTAVE
RESET
PITCH
ASSIGNABLE
IN MIDI OUT
DRUM
NUMBER
NRPN
CONTROLLER
RPN
FIXED
VELOCITY
MIDI
CH
PROGRAM
CHANGE
BANK
SELECT
TEMPO
PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER
SHIFT
GM
ON
XG
ON
CONTROLLER NUMBER LIST
122 COARSE TUNING
(NRPN)
(RPN)
120 PITCH BEND SENSITIVITY
121 FINE TUNING
123 VIBRATO RATE
124 VIBRATO DEPTH
125 VIBRATO DELAY
126 FILTER CUTOFF FREQUENCY
127 FILTER RESONANCE
128 EG ATTACK TIME
129 EG DECAY TIME
130 EG RELEASE TIME
131 DRUM FILTER CUTOFF FREQUENCY
132 DRUM FILTER RESONANCE
133 DRUM EG ATTACK RATE
13
4
13
5
13
6
13
7
13
8
13
9
14
0
14
1
74 BRIGHTNESS
84 PORTAMENTO CONTROL
91 REVERB DEPTH
92 TREMOLO DEPTH
93 CHORUS DEPTH
94 VARIATION DEPTH
95 PHASER DEPTH
73 ATTACK TIME
1 MODULATION DEPTH
5 PORTAMENTO TIME
6 DATA ENTRY
7 MAIN VOLUME
8 BALANCE CONTROL
10 PANPOT
CONTROL CHANGE
2 BREATH CONTROL
4 FOOT CONTROL
64 HOLD1(DAMPER)
65 PORTAMENTO
66 SOSTENUTO(CHORD HOLD)
67 SOFT PEDAL
69 HOLD2 (FREEZE)
71 HARMONIC CONTENT
72 RELEASE TIME
11 EXPRESSION
Changing the Octave Setting
You can easily change the octave range of the CBX-K1
keyboard while playing. In this way the three-octave
keyboard can cover the entire range of MIDI notes, from
C-2 to G8 (0-127).
To shift the keyboard up one octave, press
M. To shift the keyboard down one
octave, press N. When the octave is
changed, the LEDs rapidly flash one, two, three or four
times, according to the selected octave range. For
example, when the setting is changed to two octaves
below normal, the left lamp flashes twice.
Using the CBX-K1 — Basic Operations
NOTE
At the lowest and highest octave settings, keys
outside the legal MIDI note range will repeat the center
octave range.
Normal octave setting.
OCTAVE
ASSIGNABLE Wheel
When the CBX-K1 is turned on, this Wheel is set to control
Modulation Depth on the connected MIDI device. It can be
set to control other functions; see page 18 for details. The
Wheels maximum/minimum positions can be reversed.
(See page 20.)
PITCH Wheel
This Wheel controls Pitch Bend on the connected MIDI
device. The Wheels maximum/minimum positions can
be reversed. (See page 20.)
12
Using the SHIFT-Related Functions
The enormous flexibility and power of the CBX-K1 is in its
hidden or SHIFT-related functions allowing you to
send virtually any kind of MIDI message directly from the
keyboard or use the ASSIGNABLE Wheel for real-time
control change.
Many of the functions can be done with one or two key-
strokes, while others require you to enter a number value
and press one of the L keys to execute the function.
All functions can be accessed or executed by using one of
the operations described below.
2)
Holding C, pressing the function’s key and then
L. These functions are indicated with a dashed
underline on the panel (for example, GM ON and XG
ON) and require pressing L to execute.
3)
Holding C, pressing the function’s key, entering
a value and then pressing L. These functions
are indicated with an underline on the panel (for ex-
ample, PROGRAM CHANGE and TEMPO), and
require that a value (Decimal or Hexadecimal) be
entered.
In using the SHIFT-related functions, re-
member:
Keep holding down C until the end of the
operation. If C is released in mid-operation,
youll have to start the operation all over again.
In the instructions that follow, L refers to either of
the ENTER keys, J or K.
In other words, this means that either key can be used,
unless indicated otherwise.
NOTE
The
V
/
B
lamps flash briefly
when a function is executed or a message is sent.
The MIDI functions can be generally divided into three
types, according to their operation.
1)
Holding C and pressing the function’s key. For
these functions, such as Sequencer Stop and Start,
pressing L is not necessary. These functions are
shown on the panel without underline.
Using the CBX-K1 — Basic Operations
MIDI functions
(Group A and
Group B)
Value entry
(Decimal and
Hexadecimal)
STOP CONTINUE START
SOUND
OFF
MERGE
ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0
TRANSPOSE
HEXA
DECIMAL
DECIMAL
OCTAVE
OCTAVE SHIFT
OCTAVE
RESET
ENTER
DRUM
NUMBER
NRPN
CONTROLLER
RPN
FIXED
VELOCITY
MIDI
CH
PROGRAM
CHANGE
BANK
SELECT
TEMPO
PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER
SHIFT
GM
ON
XG
ON
L
keys
Panel Name Group A Function Group B Function
STOP Stop Song Select
CONTINUE Continue Song Position Pointer
START Start Reset All Controllers
TEMPO Tempo
BANK SELECT Bank Select
PROGRAM CHANGE Program Change
GM ON GM On
SOUND OFF All Sound Off (each channel) All Sound Off (all channels)
XG ON XG On GM-B Reset
MERGE ON/OFF Merge On/Off (each channel)
MIDI CH MIDI Channel Merge On/Off (each channel)
FIXED VELOCITY Fixed Velocity Touch Sensitivity
RPN Wheel Assign (RPN)
Controller Direct Data Send
(RPN)
CONTROLLER Wheel Assign
(controller number on panel)
Controller Direct Data Send
(controller number on panel)
NRPN Wheel Assign (NRPN)
Controller Direct Data Send
(NRPN)
DRUM NUMBER Drum Number Device Number
TRANSPOSE Q Transpose Down Wheel Invert
TRANSPOSE W Transpose Up MSB/LSB Invert
Functions Assigned to the Keyboard
13
Entering MSB/LSB Values with K (3 digit
bytes for MSB, 3 digit bytes for LSB; 6 digits total
message). For messages beginning with zeroes, the
first zeroes can be omitted.
Examples:
* 3 K
: results in a value of MSB = 000, LSB = 003.
* 0 3 K: results in a value of MSB = 000,
LSB = 003.
* 1 0 0 3 K: results in a value
of MSB = 001, LSB = 003.
* 0 1 0 0 3 K: results in
a value of MSB = 001, LSB = 003.
Entering MSB/LSB Values with J (2
digit bytes for MSB, 2 digit bytes for LSB; 4 digits total
message). For messages beginning with zeroes, the
first zeroes can be omitted.
Examples:
* 3 J: results in a value of MSB = 00, LSB =
03.
* 0 3 J: results in a value of MSB = 00,
LSB = 03.
* 1 0 3 J: results in a value of
MSB = 01, LSB = 03.
* 0 1 0 3 J: results in a
value of MSB = 01, LSB = 03.
NOTE
The order of MSB and LSB entry can be
reversed. (See page 20.)
NOTES ON THE BASIC OPERATION
If you inadvertently press two or more function keys
while performing a function, the last pressed key has
priority.
If, after entering a value, you press another function
key before pressing
L
, the value will be can-
celled.
If you enter a value that is outside of a function’s
range, it will be ignored. Legal messages can be one
byte in length (a value from 0-255).
Basic Operations
Selecting Group A and Group B Functions
Selecting Group A Functions:
Hold down C and press the appropriate key. (See
pages 14 and 18 for specific Group A functions and how
to use them.)
Selecting Group B Functions:
Hold down C and press K. The
Group B functions are available as long as you continue
to hold down C. (See pages 16 and 20 for
specific Group B functions and how to use them.)
Entering Values
Value entry on the CBX-K1 can be done in two number
systems: Decimal and Hexadecimal. The keys labeled A
through F are for Hexadecimal entry.
Entering a decimal value:
Hold down C, press the appropriate function key,
enter the desired value in decimal format, then press
K.
Entering a hexadecimal value:
Hold down C, press the appropriate function key,
enter the desired value in hexadecimal format, then
press J.
Example — Setting the MIDI Transmit Channel to 12:
Decimal:
C + { 1 2 K
Hexadecimal:
C + { c J
Value Entry — Some Specific Examples
and Anomalies
Using K
Examples:
* 1 2 K: results in a value of 12.
* a K: results in a value of 10.
* 2 a K: results in a value of 210.
* a 2 K: results in a value of 102.
* 3 a K: results in a value of 310, which is
ignored since it is outside the legal value range (0-255).
Using the CBX-K1 — Basic Operations
14
Setting the Functions
This section shows by example the operations for the basic
functions.
Using the CBX-K1 — Basic Operations
K. However, when you wish to enter a
decimal value, make sure to press K.
Likewise, when entering a hexadecimal number, make
sure to press J.
STOP CONTINUE START
SOUND
OFF
MERGE
ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0
TRANSPOSE
HEXA
DECIMAL
DECIMAL
OCTAVE
OCTAVE SHIFT
OCTAVE
RESET
ENTER
DRUM
NUMBER
NRPN
CONTROLLER
RPN
FIXED
VELOCITY
MIDI
CH
PROGRAM
CHANGE
BANK
SELECT
TEMPO
PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER
SHIFT
GM
ON
XG
ON
Group A Operations
Sending a Simple Command
Operation: C + Function Key
Relevant Functions: Sequencer Stop/Continue/Start; Sound Off
1
Example: Sending a Start command to a sequencer or rhythm machine
C + E
You can use the Q and W keys in the same
way, to stop the sequencer or continue playback from the
stopped point.
2
Setting a Simple Command (on/off)
Operation: C + Function Key
Relevant Functions: Merge On/Off
Example: Switching the MIDI Merge function of the CBX-K1 on or off
C + P
Sending a Simple Command with L
Operation: C + Function Key L
Relevant Functions: GM System On; XG System On
Setting a Specific Value for a Function
Operation: C + Function Key Value L
Relevant Functions: Tempo; Program Change; MIDI Channel;
Fixed Velocity; Controller; Drum Number; Transpose
Down/Up
4
Example: Changing the tempo value on a sequencer or rhythm machine
C + R 1 4 0 K
Example: Setting a connected tone generator to XG Mode
C + O L
NOTE
Either
L
key can be used for these
commands.
3
1 1 5 4 1 2 4 5
7
5
7
6
4
6
4
8433 4
7
41
Numbers 1 - 8 in the illustration correspond to the operation
numbers below.
* Unless indicated otherwise, L refers to either of
the ENTER keys, J or
15
Setting a Specific Value for a Function
(MSB, LSB)
Operation: C + Function Key MSB value LSB value
L
Relevant Functions: Bank Select; RPN; NRPN
Example: Selecting a Bank of Voices on a Tone Generator
Some tone generators feature two or more banks of voices. This
example shows how to use the Bank Select function to select
different banks. This example also shows you how to use the
functions that require entry of two values: MSB and LSB.
In this example, we’ll enter a value of 012 (MSB) 034 (LSB)
C + T 0 1 2 0 3
4 K
NOTE
Decimal values of MSB and LSB are 3 digits
each (6 digits total); hexadecimal values are 2 digits
each. Zeroes must be entered, unless they occur at the
beginning of the value. For example, for the decimal
value of 001 (MSB) 012 (LSB), the first two zeroes may
be omitted, but the third must be entered. In other
words, the value could be entered as
1
0
1
2
.
Transpose Setting
Operation: C + G / H
6
To transpose up one semitone, use the H key
(F3). To transpose down one semitone, use the
G key (E3). Each repeated pressing of the
key while holding C transposes the pitch by an
additional semitone. To restore the normal default trans-
pose setting, hold down C and press both
G / H keys simultaneously.
NOTE
You can also enter transpose values directly by
using operation 4 above.
Setting a Specific Value for a Specific
Controller
Operation: C + Function Key Controller Number
L Value(s) L
Relevant Functions: RPN*; Controller; NRPN*
Functions marked with an asterisk (*) above require that
you enter two values: an MSB (Most Significant Byte)
and an LSB (Least Significant Byte).
5
7
Example: Changing the Portamento Time of a tone generator’s voice
C + S 5 (Portamento Time) L
{2 5 L}
The operation steps enclosed in brackets ({}) can be
repeated or re-entered as long as C is held.
NOTE
This operation assigns a controller number for
the ASSIGNABLE Wheel and sends a specific value for
that controller number. You can also send a specific
value for the controller (in the Group B functions)
without altering the controller assignment.
Selecting a Drum Number (when editing
a specific drum number with controller
numbers 131 - 141)
You can use operation 4 above to set the drum number
for editing a specific drum number with controller numbers
131 - 141. However, the following operation lets you set
the Drum number by playing it from the keyboard. This
allows you to hear the drum sound youll be editing, since
the last note played on the keyboard determines the drum
sound to be changed.
Without pressing C, find the desired drum number by
sound by pressing keys on the keyboard. Next, hold
down C, press F, then L. This
sets the drum number to the last key pressed. Then (to set
the controller number for that drum sound), hold down
C and press S, then enter the controller
number (131 through 141). This sets the Controller Num-
ber for the Drum parameter you wish to control with the
ASSIGNABLE Wheel.
8
Using the CBX-K1 — Basic Operations
16
Using the CBX-K1 — Basic Operations
Group B function names are not shown on the panel. For
the list and explanations of Group B functions, refer to
pages 12 and 20.
119
Example: Sending a Reset All Controllers command to a sequencer or
tone generator
C + K E (Reset All Controllers)
Setting a Simple Command (on/off)
Operation: C + K Function Key Value
Relevant Function: Merge On/Off (each channel)
Example: Setting a connected tone generator to GM-B Reset
C + K O (GM-B Reset) L
Setting a Specific Value for a Function
Operation: C + K Function Key
Value L
Relevant Functions: Song Select; Touch Sensitivity; Device
Number
Sending a Simple Command with L
Operation: C + K Function Key
L
Relevant Function: GM-B Reset
Sending a Simple Command
Operation: C + K Function Key
Relevant Functions: Reset All Controllers; Sound Off (all
channels); Wheel Invert; MSB/LSB Invert
12
10
Example: Switching the MIDI Merge function of the CBX-K1 on or off for
MIDI channel 12
C + K { (Merge On/Off for each
channel) c (for MIDI channel 12)
Keys 1 - f and 0 correspond to MIDI channel 1-
15 and 16, respectively. Pressing each key toggles the on/
off status of each channel.
Example: Changing the touch sensitivity of the CBX-K1 to 10
C + K } (Touch Sensitivity)
1 0 L
Numbers 9 -
14
in the illustration correspond to the
operation numbers below.
Group B Operations
STOP CONTINUE START
SOUND
OFF
MERGE
ON/OFF 1 2 3 4 5 6 7 8 9 A B C D E F 0
TRANSPOSE
HEXA
DECIMAL
DECIMAL
OCTAVE
OCTAVE SHIFT
OCTAVE
RESET
ENTER
DRUM
NUMBER
NRPN
CONTROLLER
RPN
FIXED
VELOCITY
MIDI
CH
PROGRAM
CHANGE
BANK
SELECT
TEMPO
PROGRAM RESET SYSTEM WHEEL ASSIGNSEQUENCER
SHIFT
GM
ON
XG
ON
9 99 9
12 12 14 14
121413 11 10
* Unless indicated otherwise, L refers to either of
the ENTER keys, J or
K. However, when you wish to enter a
decimal value, make sure to press K.
Likewise, when entering a hexadecimal number, make
sure to press J.
1 / 1

Yamaha CBX-K1 Manuale del proprietario

Categoria
Strumenti musicali
Tipo
Manuale del proprietario