Hoover HNWF 6137-80 Manuale utente

Instruction Book

HNWF6137 Washer/Dryer

40001478Eng.qxd 02/09/2004 20:16 Page 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Delivery information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Do’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Don’ts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Choose a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Electricity supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting to the cold water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connection of the machine to the drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Moving the machine into position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Testing the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Washing and Drying advice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Loading your washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sorting the laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

The Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Dispensing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Wash and Dry Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Programme Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Special Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Daily Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

A Typical Wash and Dry Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Starting the cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Cleaning and Routine Maintenance. . . . . . . . . . . . . . . . . . . . 31

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

2

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

40001478Eng.qxd 02/09/2004 20:22 Page 2

Introduction

Please read and follow these instructions

carefully and operate the machine accordingly.

This booklet provides important guidelines for

safe use, installation, maintenance and some

useful advice for best results when using your

machine.

Keep all documentation in a safe place for future

reference or for any future owners.

Delivery information

Please check that the following items are

delivered with the appliance:

● Instruction manual

● Guarantee card

● Blanking plug

● Inlet hose & hooked end support

(see Unpacking and Installation Instructions)

● Base panel & x2 push clips

● Energy Label

Do’s

● All packaging materials used are

environmentally-friendly and recyclable.

Please help dispose of the packaging via

environmentally-friendly means. Your local

council will be able to give you details of

current means of disposal.

● To ensure safety when disposing of an old

washing machine disconnect the mains plug

from the socket, cut the mains power cable

and destroy this together with the plug. To

prevent children shutting themselves in the

machine break the door hinges or the door

lock.

● This machine is solely for domestic use,

i.e. to wash, rinse and spin dry household

textiles and garments.

3

Check that no

damage has

occurred to the

machine during

transit. If it has,

call for service

by GIAS.

40001478Eng.qxd 02/09/2004 20:22 Page 3

Don’ts

● Do not touch the appliance when hands or

feet are damp or wet.

● Do not lean on the door when loading the

machine or use the door to lift or move the

machine.

● Do not use adapters, multiple connectors

and/or extensions.

● Do not allow children to play with the

machine or its controls.

● Do not try to open the door when water is

visible in the drum or the Blocco Porta

indicator is on.

4

Failure to

comply with

the above can

compromise the

safety of the

appliance. You

may be charged

for a service call

if a problem

with your

machine is

caused by

misuse.

If the appliance

is not running

properly or

breaks down,

switch it off,

disconnect the

plug from the

socket, turn off

the water

supply and do

not tamper

with the

appliance.

Consult GIAS

Service for

possible repair.

40001478Eng.qxd 02/09/2004 20:16 Page 4

Unpacking the product

Remove the machine from its packaging close to

the final location of the machine.

1. Cut carefully around the base of the

packaging.

2. Lay the machine on its back and remove the

base and the two polystyrene spacers on

each side of the machine. We recommend

that a second person assist in the lifting and

manoeuvring of the machine.

3. Return the machine to the upright position,

remove the remainder of the packaging and

the central screw in the transit bar.

4. Remove the four retaining screws in the

transit bar and pull out the transit bracket.

5

Dispose of the packaging safely.

Make sure it is out of the reach

of children, it is a potential

source of danger.

40001478Eng.qxd 02/09/2004 20:16 Page 5

5. Take the base panel provided and fit the

two self adhesive strips by removing the

backing paper on one side and locating the

strips on each side of the base panel.

6. Tilt the machine forward and locate the

base panel under the front of the machine.

Remove the remaining backing paper from

the self-adhesive strips and offer up the

base panel to the bottom of the cabinet.

7. Take the two plastic fixing clips and fix the

base panel to the base of the machine.

Bring the machine back to the upright

position.

6

We recommend you keep the transit bracket and

screws to protect the machine for future transit.

The manufacturers will not be responsible for any

damage to the machine caused by not following the

instructions relating to releasing the transit protection.

The user is responsible for all installation costs.

40001478Eng.qxd 02/09/2004 20:16 Page 6

8. Cover the central hole in the rear of the

machine with the cap enclosed in the

instruction bag.

Choose a location

● After the machine has been installed, ensure

that the mains plug and water supply valves

are easily accessible.

● Make sure there is enough space for the

machine. Select a space at least 600mm wide

and 850mm high. Also leave enough space

to open the door fully so you can load and

unload it easily.

● Keep the area underneath and around the

machine free of combustible materials such

as lint, paper, rags, chemicals etc.

7

Installation

Do not plug the

machine in and

switch it on at

the mains until

the installation

is completed.

40001478Eng.qxd 02/09/2004 20:16 Page 7

Electricity supply

Washing machines are supplied to operate at a

voltage of 230V, 50 Hz single phase. Check that

the supply circuit is rated to at least 16A.

Electricity can be extremely dangerous.

This washing machine must be earthed.

The socket outlet and the plug on the appliance

must be of the same type.

Do not use multiple adapters and/or extension

leads.

The wires in the mains lead are coloured in

accordance with the following codes:

Blue NEUTRAL

Brown LIVE

Green and Yellow EARTH

CE Appliance complies with European Directive

89/336/EEC, 73/23/EEC and subsequent

amendments.

Water supply

● The cold water pressure should be between

0.05-0.8 Mpa.

● Do not connect the machine to a single

outlet instantaneous water heater.

● The water supply tap should be accessible

when the machine is installed.

● Before connecting the fill hose, check that

the water is running from the water supply

tap to be used.

8

You may be

charged for a

service call if a

problem with

your machine is

caused by

incorrect

installation.

If the mains

cord on this

appliance is

damaged, it

must be

replaced by a

special cord

which is ONLY

obtainable from

the GIAS spares

service. It must

be installed by

a competent

person.

40001478Eng.qxd 02/09/2004 20:16 Page 8

Connecting to the cold

water supply

This machine has an inlet hose with a 19mm

(3/4") threaded ferrule fitted to the end, to

attach between the threaded connector on the

appliance and the water supply.

Only use the new hose supplied to connect the

machine and ensure that the sealing washers are

in place inside the hose connectors.

Do not re-use old hoses which are attached to

existing installations.

Do not over-tighten the connections. Hand tight

is sufficient.

Do not trap or kink the hose.

1. Connect the elbow end of the hose provided

to the threaded inlet on the back of the

machine.

Grey pipe to the white threaded inlet on

the machine.

2. Hand tighten the connector.

3. Connect the straight ends of the pipes to

the water supply; ensure that there are no

kinks.

4. Turn on the water supply and check for

leaks. If there is a leak, turn off the water

supply, disconnect the hose and check the

sealing washers are in place. Refit the hose

and turn on the water supply.

9

40001478Eng.qxd 02/09/2004 20:17 Page 9

Connection of the machine to the

drain

This machine must be connected in accordance with the water supply

regulations. Water byelaws prohibit connection to a surface water drain.

Decide which plumbing option suits you best then follow the instructions

below.

Option 1

Waste pipe connection (waste trap)

Fit the hooked end support to the outlet pipe. Position at least 800mm off the

floor.

After removing the blanking plug or cutting the membrane from the waste

system securely fix the outlet pipe to the drainage system, using a hose clip.

Secure the hooked end support up to at least 800mm to avoid water being

drawn back into the machine.

10

All machines are tested with water prior to leaving the

factory so a small amount of water may remain in the

drum and drain hose.

Flooding could occur if any part of the installation is

not completed correctly.

flexible

discharge hose

sink

trap with hose

adaptor

800 mm

hose clip

hooked end support

40001478Eng.qxd 02/09/2004 20:17 Page 10

Option 2

Into a standpipe

Ensure that the standpipe is not located near

an electrical socket.

Fit the hooked end support to the outlet pipe.

Install the hose into the standpipe ensuring

that the pipe is at least 500mm from the floor.

Insert the outlet pipe approximately 100mm

into the standpipe.

Moving the machine

into position

Your machine is heavy so care must be taken

when moving it. We recommend that two people

move the machine to avoid strain and possible

injury.

● Take care not to damage flooring when

moving the machine.

● When moving the machine to its final

position take care not to kink or damage

the hose at the back of the machine.

Adjusting the feet

Once the machine is in place the feet should be

adjusted to ensure that the machine is level. If

the machine is not level it may become noisy or

move.

Adjust the feet on the front corners of the

machine until the machine is firm and level.

When the machine is firm and level, tighten the

locking nuts on the two feet.

11

100 mm

500 mm min

Do not drag or

lift the machine

by its door.

40001478Eng.qxd 02/09/2004 20:17 Page 11

Refer to the programme guide for details of how

to select programmes.

1. Turn on the water supply and check for

leaks from the fill hose.

2. Switch on the electricity supply.

3. Select the spin programme / and

then press the Avvio Pausa button to start

the machine. Allow the programme to

continue for one minute and then cancel

the programme by returning the selector to

the OFF position. This will remove any water

remaining in the machine from factory

testing.

4. To check for cold water filling to the

machine:

Select the rinse programme / and

press the Avvio Pausa button to start the

machine.

Allow the tumble action to continue until

the water has pumped out. Check that the

drain outlet is not leaking or overflowing.

5. Switch off the machine at the end of the

cycle by turning the programme knob to the

OFF position.

6. Select the spin programme / and

press the Avvio Pausa button to switch the

machine on. If the machine takes longer

than one minute to empty check the drain

hose for kinks.

Installation testing is now

complete.

Now you have successfully installed the machine

we advise that you run the machine to ensure the

drum is thoroughly clean after testing and

storage. Select Cotone Resistente programme and

run the machine for a complete cycle using only

wash detergent and water. Ensure that the drying

timer is in the OFF position.

12

Testing the installation

This

programme

will take

approximately

2 hours to

complete.

40001478Eng.qxd 02/09/2004 20:17 Page 12

The following tips are designed to assist in getting the best results from your

machine whilst utilising it in the most environmentally-friendly and

economical way. It is also important to understand the items to avoid in your

laundry, to ensure the continued safe and reliable operation of your machine.

Loading your washing machine

To make further reductions of energy, water and detergent consumption, we

recommend that you put a full load into your machine. Energy savings of up

to 50% can be achieved by washing one full load compared to two half loads.

Do not overload the machine as this will reduce the quality of the wash and

may cause damage to the machine and your laundry.

When is prewashing really needed?

Only with particularly dirty loads! Energy savings of 5 to 15% are made by not

selecting the prewash option for less dirty laundry. Pre-treat awkward stains

with a washable stain remover.

Which wash temperature should you choose?

Using stain removers before machine washing reduces the need to wash at

temperatures over 60°C.

Using a 40°C wash temperature can make energy savings of up to 50%.

Heavily soiled laundry

To ensure the best performance when washing a particularly dirty load, we

recommend that you reduce the amount of items to be put into the machine.

Allowing more space in the drum the items can circulate more freely and will

wash cleaner.

Sorting the laundry

Items to avoid

We recommend that you do not wash underwired bras in the machine. Should

the wires become detached it could cause damage to your clothes and the

machine. If the washcare label states that the bra is machine washable then

we advise placing it in a wash bag.

Recommendations

Always follow the wash care labelling on the garments.

Fasten zips, tie strings and close press studs to prevent tangling. Ensure that

pockets are emptied of loose change and other small items.

13

Washing and Drying advice

40001478Eng.qxd 02/09/2004 20:17 Page 13

Check that there are no metal objects in the laundry as these may damage the

laundry and the machine. Place small items in a wash bag.

Drying

In addition to the above advice the guidelines below must be followed when

drying the clothes.

Sort the load for drying:

● By care symbols:

These can be found on the collar or inside seam:

Suitable for tumble drying. Tumble drying at high temperature.

Tumble drying at low temperature only. Do not tumble dry.

If the item does not have a care label it must be assumed that it is not suitable

for tumble drying.

● By amount and thickness

Whenever the load is bigger than the dryer capacity, separate clothes

according to thickness (e.g. towels from thin underwear).

● By type of fabric

Cottons/linen: Towels, cotton jersey, bed and table linen.

Synthetics: Blouses, shirts, overalls, etc. made of polyester or polyamid, as

well as for cotton/synthetic mixes.

Things to avoid

● Do not tumble dry woollens, silk, delicate fabrics, nylon stockings,

delicate embroidery, fabrics with metallic decorations, garments with PVC

or leather trimmings, training shoes, bulky items such as sleeping bags, etc.

● Do not dry articles which have been treated with a dry cleaning fluid or

rubber clothes (danger of fire or explosion).

● Foam rubber materials can, under certain circumstances, when heated

become ignited by spontaneous combustion. Foam plastic, foam rubber

and rubber-like material are not suitable for tumble drying. Articles

made from these materials MUST NOT be placed in the dryer.

● Do not try to dry items that are dripping wet, this may damage the

appliance. Spin these items first.

14

Do not use the machine to wash and dry items that do not

have a wash label.

Do not wash and dry items previously treated with solvents.

40001478Eng.qxd 02/09/2004 20:17 Page 14

Detergent dosage

Only use detergents which are suitable for use in a washing machine. You will

obtain the best results from your wash with the minimum use of chemical

products, and the best care for your laundry if you take into consideration the

degree of soiling as well as the type of detergent to choose.

The amount of detergent to use depends on:

● Water hardness.

Depending on the hardness of the water and the type of detergent used,

it is possible to reduce the amount of detergent.

The softer the water supply, the less detergent is required.

● The degree of soiling.

It is possible to reduce the amount of detergent used depending on the

degree of soiling.

Use less detergent for less soiled items.

● Amount of laundry.

It is possible to reduce the amount of detergent when washing only a

small amount of laundry.

For smaller loads use less detergent.

The dosages shown on the packaging of detergents for washing delicates

often already refer to a reduced wash size. Always follow the dosage

instructions on the detergent packaging.

15

The Dispenser

DO NOT exceed the maximum detergent dosage

COMPARTMENT I

Prewash detergent

Maximum dosage 100ml of powder

COMPARTMENT II

Mainwash detergent

Maximum dosage 200ml

of powder

COMPARTMENT

Fabric Conditioner

Maximum dosage 100ml

40001478Eng.qxd 02/09/2004 20:17 Page 15

ARIEL – Chosen and recommended

by HooverZerowatt

When we produce a new washing machine we

subject it to every test possible. One of the most

important tests is the one that enables our experts

to identify the most suitable detergent for solving

laundry problems. Ariel was able to meet our

needs: to make the washing machine function

efficiently; not compromise the machine’s lifespan;

and produce the best wash results. Consistently

excellent results, which was the main aim of the

test we carried out, determined our choice and our

recommendation. The prime function of a

detergent that answers all washing requirements is

to work with the water to remove dirt from

fabrics, holding it in suspension, until it is removed

when the water is pumped out, and to control the

amount of foam forming in the washing machine,

without damaging the fibres of the items being

washed. Ariel fully satisfies all these requirements,

as it contains high quality elements, the result of

the most advanced research, ensuring excellent

results under all conditions.

Dispensing instructions

The detergent drawer is split into 3 compartments:

● the first, labelled "I", is for detergent utilised

during Prewash.

● the second, labelled "II", is for detergent

utilised during the main wash.

● the third, labelled is for special additives

such as fabric softeners, fragrances, starch,

brighteners etc.

Dispensing in the drum

Liquid detergents and some tablets are dispensed

via the machine drum using the recommended

dispensing device which is placed upright on top of

the washload towards the back of the drum. Some

tablets are designed to be placed in the dispenser

drawer, check the detergent pack for details.

16

Do not put any

items into the

drawer other

than detergents

that are

designed to be

dispensed from

the drawer as

they may cause

blockage or

damage.

40001478Eng.qxd 02/09/2004 20:17 Page 16

Turning the machine On

The machine is turned on by selecting a programme via the programme

selector. This status will be indicated by the STOP indicator light flashing, this

light will continue to flash until the machine has started or the machine is

returned to the OFF position.

Start/Pause (Avvio Pausa)

Start (Avvio)

After selecting the programme and the required options press the Avvio Pausa

button once to start the machine. The STOP light will stop flashing and START

light will illuminate and there will be a short time delay to the start of the

programme while the machine sets the wash parameters for the selected

programme and options. If the duration of the programme you have selected

17

The Control Panel

The programme selector must be returned to the OFF

position to reset the controls between each wash

cycle.

CHRONOVISION

Display

Door Locked Indicator

(Blocco Porta)

Start/Pause

(Avvio

Pausa)

Delay Start

(Partenza

Differita)

Pre Wash

(Pre Lavaggio)

Extra Rinse

(Extra

Risciacquo)

Spin Speed

Reduction

(Riduzione

Centrifuga)

Drying Time

Selector

(Tempo

Asciugatura)

Temperature

Selector

(Temperatura

Lavaggio)

Programme

Selector

40001478Eng.qxd 02/09/2004 20:17 Page 17

is shorter than 60 minutes, then the time

remaining indicator will illuminate accordingly.

The Blocco Porta indicator light will also

illuminate a few seconds after pressing the Avvio

Pausa button.

Pause (Pausa)

The programme may be paused at any time

during the wash cycle by holding down the Avvio

Pausa button for about two seconds. When the

machine is in the paused mode, the time

remaining for the programme in the

CHRONOVISION indicator and option buttons will

flash. The Blocco Porta indicator light will remain

illuminated for approximately 2 minutes. The

door can be opened when this indicator goes out.

To restart the programme, press the Avvio Pausa

button once again.

Cancelling and changing the

programme

To cancel the programme the programme selector

should be rotated to the OFF position.

Select a new programme and start as detailed

above.

Door Locked indicator (Blocco

Porta)

The Blocco Porta indicator light is illuminated

when the door is fully closed and the machine is

ON.

When Avvio Pausa is pressed on the machine with

the door closed the indicator will flash

momentarily and then illuminate. If the door is

not closed the indicator will continue to flash.

A special safety device prevents the door from

being opened immediately after the end of the

cycle. Wait for 2 minutes after the wash cycle has

finished and the Blocco Porta light has gone out

before opening the door. As a safety measure,

check that there is no water evident in the drum.

At the end of the cycle turn the programme

selector to OFF.

If the programme is paused, the door locked

indicator will go out after 2 minutes and the door

18

When starting a

subsequent

wash cycle the

programme

selector must

be returned to

OFF prior to the

being selected

and started.

40001478Eng.qxd 02/09/2004 20:17 Page 18

can be opened. Check there is no water evident

in the drum before opening the door.

CHRONOVISION

In order to better manage your time, this washing

machine features an indicator light system that

keeps you constantly informed on the remaining

cycle time and the status of the start delay

function.

When a drying time is selected the

CHRONOVISION display will display the time

remaining on the washing programme when the

washing is taking place and the time remaining in

the drying phase when drying is taking place.

19

START

60'

30'

15'

STOP

Remaining time above

60 minutes

Remaining time less

than 60 minutes

Remaining time less

than 30 minutes

Remaining time less

than 15 minutes

End of the programme

3h

6h

9h

3 hours or less remaining

before the programme

commences

6 hours or less remaining

before the programme

commences

9 hours or less remaining

before the programme

commences

CHRONOVISION DISPLAY

WASH PROGRESS

START DELAY

40001478Eng.qxd 02/09/2004 20:17 Page 19

Start Delay (Partenza Differita)

This option is available to delay the start of the wash cycle by up to 9 hours.

The selection of the time is completed by pressing the Partenza Differita

button, the CHRONOVISION display will indicate the time selected. When the

correct delay is selected press the Avvio Pausa button to start the cycle.

Prewash (Pre Lavaggio)

This option is available on the cottons and synthetics programmes. Prewash is

automatic on the Sports programme. This option is particularly useful for

heavily soiled loads and can be used before selecting the main wash

programme. Detergent for this programme should be added to the first

compartment of the soap drawer labelled "I" (Please refer to Detergent

Drawer section of manual). We recommend you only use 20% of the main

wash detergent quantity.

Extra Rinse (Extra Risciacquo)

This option is available on the cottons programmes. The option increases the

number of rinses to five (including the final conditioned rinse). This can help

prevent skin irritation from detergent residue for people with particularly

sensitive skin. Selecting the Extra Risciacquo button is also recommended

when washing heavily soiled fabrics which need a lot of detergent, or when

the wash load contains towelling fabrics that have a greater tendency to

retain detergent.

Spin Reduction (Riduzione Centrifuga)

This option is available on the Cottons programmes, AA 40°C, Lavaggio Classe

A 59', Sports and Rapido programmes to reduce the maximum spin speed to

600rpm thus reducing creasing. It is not recommended that this option be

selected when a drying programme will follow, as the length of the drying

cycle will be increased.

Temperature Selector (Temperatura Lavaggio)

The washing machine is equipped with a Temperature Selector knob to set the

temperature you require. Bigger energy savings can be achieved by using the

lower temperature settings around the dial between and 40°C. By

selecting the position, the wash temperature is limited to the water inlet

temperature, thus reducing energy consumption further. We recommend that

20

Wash and Dry Options

The options should be selected BEFORE pressing the

Avvio Pausa button

40001478Eng.qxd 02/09/2004 20:17 Page 20

La pagina sta caricando ...

Hoover HNWF 6137-80 Manuale utente

Questo manuale è adatto anche per

Hoover HNWF 6137-80 Manuale utente

Documenti correlati

Altri documenti