Zenith L10V34H Installation And Setup Manual

Installation and Setup Guide | Warranty

Model Number | L10V34H | L10V34S | LCD TV/Monitors

table of contents

page

5

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

THIS PRODUCT MUST BE USED WITH UL LISTED MOUNTING BRACKET.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3-WIRE COMM-WARN B-2/02

RECORD THE SERIAL NUMBER

The model and serial number of this LCD TV/Monitor are

located on the back of the cabinet. For future reference, we

suggest that you record the serial number here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

For Customer Support/Service please call:

1-888-865-3026

www.zenith.com

PAGE 3

206-3824

Important safeguards for you and your new product

This product has been manufactured and tested with safety in mind. However, improper use can result in potential electri-

cal shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and

observe the following safety points when installing and using the new product, and save them for future reference.

Observing the simple precautions discussed in this installation and operating guide can help get many years of enjoyment

and safe operation that are built into the new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

PORTABLE CART WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or

on an unstable cart, stand, tripod, bracket, or table. The

product may slide or fall, causing serious injury to a child

or adult, and serious damage to the product. Use only with

a cart, stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. Any mounting of

the product should follow the manufacturer’s instructions,

and should use a mounting accessory recommended by the

manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Power Cord Polarization (Some models)

This product is equipped with a three-wire grounding type

alternating-current power plug. This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the three-wire ground-type

plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

PAGE 4

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

206-3824

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service

personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following

conditions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a quali-

fied technician to restore the product to its normal

operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer. The product may slide or

fall, causing serious injury to a child or adult, and serious

damage to the product.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 5

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up the LCD TV/Monitor

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation/Connections Overview . . . . . . . . . . . . . . 7

VESA Standard TV Mounts . . . . . . . . . . . . . . . . . . . . 8

Install TV on Stand . . . . . . . . . . . . . . . . . . . . . . . . 9

TV and other Equipment Hookup

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 12

Cable Service with VCR . . . . . . . . . . . . . . . . . . . . . 13

DC Power Hookup/Master Power Switch . . . . . . . . . . . 14

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . 15

Menus and Displays Overview

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 16

Other Menus and On-Screen Displays . . . . . . . . . . . . 17

Optional Installer Remote Control Key Functions . . . . . 18

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

(Select OFF AIR ANTENNA, or CABLE TV and do a channel

search)

Step 3. Customize the LCD TV/Monitor

Features

Setup Menu (Starts with page 19, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Timer (On/Off Timers) . . . . . . . . . . . . . . . . . . . . . . 23

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . . . 24

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Bass, Treble, Balance, Audio Mode, Front Surround,

Sound Rite, Speakers

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

Installer Parental Control Menu . . . . . . . . 28 - 29 - 30

Set up Parental Control for the end user.

Managing the Channel Banks . . . . . . . . . . . 31 - 32 - 33

Installer Menus . . . 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41

LT2000 Quickset II Clone Programmer . . . . . 42 - 43 - 44

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . 46

User Operation Section (Copy for User)

Optional L10V34S Remote Control Key Functions . . . . 47

User Parental Control Menu . . . . . . . . . . . . . . . 48 - 49

User Menus and On-Screen Displays . . . . . . . . . . . . . 50

User Front Panel Controls . . . . . . . . . . . . . . . . . . . 51

Warranty for Concierge Series TVs . . . . . . . . . Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To perform a normal installation set up, you need an installer’s remote such as the one shown, and the LT2000 Quickset II

Clone Programmer—both are shown and described in later sections. The installer remote allows access to the Installer

menus, User menus, and Channel Banks in the Manual Channel Set options on the Setup menu. The installer remote has

Menu, Select, and Adjust Keys. The LT2000 Quickset II Clone Programmer is used to duplicate a TV’s setup and install it on

another identical TV. See your Zenith Dealer.

Note: Design and specifications are subject to change without prior notice.

206-3898

The table of contents lists the pages to go to for setting up the features for the end user

Optional User’s Remote Control for Model No. L10V34S

Shown herein is an optional user’s remote control available for the L10V34S model only. The remote control is NOT

included with the LCD TV/Monitor. However, the user’s remote can be purchased separately, see your Zenith dealer.

Instructions for operating the remote can be found on page 47. Photocopy Guest operation pages as needed.

PAGE 6

206-3824

Setup Checklist

Installation Overview

• Unpack the LCD TV/Monitor and all

accessories.

• Determine installation location for

the LCD-TV, TV stand, and if used,

optional AC to DC Power Converter.

• Determine mounting and installation

requirements. If used, AC Power source

outlet, Antenna/Cable service connec-

tors, any external equipment required

for system or TV operation, all neces-

sary cables, wires, connectors and any

other additional required hardware,

etc.

Installation Overview & System

Setup: Questions to Consider Before

Installation

VESA Bracket

Does the VESA Bracket have to be mount-

ed to the TV? Y: Install VESA Bracket on

TV following the instructions supplied with

the bracket.

Yes___ No___

TV Stand

Does the TV have to be mounted on the

stand? Y: Mount the TV on the stand fol-

lowing the instructions provided with the

TV stand.

Yes___ No___

Optional AC to DC Power Converter

Installation

Does the optional AC to 12V DC Power

Converter need to be mounted on a wall?

Y: Install the AC-DC Power Converter on a

wall or in an appropriate location.

Yes___ No___

Installer’s Remote Control

Does the Installer have an optional

Installer’s remote control to use to set up

the TV (This is a must for TV setup.)?

Yes___ No___

Master TV Setup

Will the Master TV’s features setup be

cloned and be copied to other identical

LCD TV/Monitors?

Yes___ No___

Clone Programmer

To copy the TV’s setup, the installer will

need a clone programmer. Is there a Zenith

LT2000 Clone Programmer available?

Yes___ No___

End-User Remote Control

Will a remote control be provided to the

end user to operate the TV? (No remote is

included with the TV.)

Yes___ No___

End-User Menu Access

Will the end-user have access to all the

menus on the TVs from the front panel?

Yes___ No___

LCD-TV Setup Checklist

1. Install the LCD TV/Monitor where it will

be used.

Prior to Operation

The LCD TV/Monitor must be connected to

all external antenna/cable, video, and

audio source equipment and a DC power

source. See page 5, Table of Contents.

2. Make all external source equipment con-

nections. See pages 10 - 14.

3. Connect DC power or, connect the

optional AC to DC power converter to

the LCD-TV first, insert the DC power

plug into the jack provided on the back

of the TV. Then connect the converter

to a standard 120V, 60 Hertz, AC power

source. See page 14.

Master Power Switch

Once all antenna/cable and external equip-

ment connections have been made, the

master power switch located on the back

of the TV must be set to the standby posi-

tion, ‘I’. To turn the TV’s master power

switch off, set the switch to the ‘O’ posi-

tion. See page 7.

4. Turn on the TV and all source equip-

ment.

Review TV Setup Options in the

Installer’s Menu Section

The Installer’s menu includes a number of

options for the master TV’s setup that

enable the installer or system administra-

tor to devise a unique system using the

many different options and variables avail-

able. See Installer’s menus section.

Master TV Features Setup for

Cloning Overview

• Set up Installer’s remote control, see

page 18.

• Select Tuning Band and do Channel

Search, see page 19.

• Channel Add/Delete/Blank.

• Channel Banks Setup, see Channel Banks

Setup section.

• Video/picture appearance options setup,

see Video menu.

• Audio/sound options setup, see Audio

menu.

• Set up all other features. See page 5,

Table of Contents, for a list of features

available on this LCD/Monitor.

Clone Master TV’s Setup

See Clone Programmer section.

Installation/Connections Overview

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

PAGE 7

206-3824

To hook up source equipment, see below

and also refer to the Table of Contents

on page 5; shows pages to go to for

equipment hookup options.

AUDIO/VIDEO IN

Connect Audio/Video

equipment to these jacks.

See pages 12 - 13.

ANTENNA/CABLE

Connect to an

antenna or cable

system.

See pages 10 - 13.

MASTER POWER

SWITCH

‘I’ switches the LCD-TV

into standby mode.

‘O’ Turns the power off.

M.P.I. INTERFACE

Use with clone

programmer.

See pages 42 - 44.

DC POWER INPUT

(Optional AC - DC converter is

available.) See page 14.

PAGE 8

206-3824

VESA Standard TV Mounts

VESA Standard 75mm TV Mounts and Stands

Following are shown some examples of VESA standard 75 mm mounts. Since there are numerous

types of stands and mounts available, only a few are shown here. Refer to the instructions provided

with the TV stand that will be used to mount the TV.

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

75 mm

General Guidelines: Choosing a location for

installing a VESA Standard Mount

Be sure the style of stand selected is capable of supporting the

weight of the TV.

If the mount will be on a wall, a typical wooden stud behind the

wall board would be the preferred choice for a location to attach

the wall mount. The wall mount location chosen should be appro-

priate for drilling holes and have available the required power

source as well as antenna/cable and other equipment leads.

For pedestal-type mounts, a sturdy surface on a desk or other

similar flat table-like surface would be the appropriate location

for mounting a pedestal-style TV stand. (Some stands are

portable and can be moved from one location to another.) Be

sure all safety considerations are followed.

Most stands are designed so that the wiring would be threaded

through the stand itself or a loop-through style clamp so that

the wiring is neatly bunched and not strung in such a way as to

create a potential hazard to the user.

Typical Wall Stud Type Mount with Swivel Bracket

Typical Pedestal Type Mount with Swivel Bracket

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

PAGE 9

206-3824

Install TV on VESA Standard TV Mount

Installing the TV on VESA Standard 75mm TV Mounts and Stands

Follow the instructions provided with the mounting bracket that will be used for the installation.

Since there are numerous types of TV stands and brackets which can be used, these instructions are

included and should be thought of only as general guidelines for installing the TV on a mount.

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

RF IN

RJ45

IN

RJ11

IN

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

RF IN

RJ45

IN

RJ11

IN

General Guidelines: Preparation for

TV installation on a VESA Standard

Mount

Remove the two machine screws hold-

ing the connection panel cover in

place.

Remove the two screws holding the

cable clamp in place, remove clamp.

Make all necessary external equipment

and other connections to the TV. (See

pages 10 - 14.)

Thread all cables into the clamp recess

on the TV cabinet.

Replace the cable clamp, reinstall the

two screws.

Replace the connection panel cover,

reinstall the two screws.

Mount TV to stand as required. See

stand installation instructions.

1

2

3

5

4

6

7

Note: Shown with optional AC to

DC Power Converter connected.

PAGE 10

206-3898

Antenna Hookup

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of the TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

Connect an off-air antenna to the

LCD TV/Monitor

If the antenna is a 75 ohm RF cable, then no

adapters are required.

A 300 to 75 ohm adapter is not included with

the Zenith LCD TV/Monitor.

300 TO 75 OHM

ADAPTER

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

Antenna

Connections Panel

RF Coaxial Wire

(75ohm)

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

Locate the Antenna/Cable jack on the back

of the LCD TV/Monitor.

Connect the antenna wire (Flat or Round)

that runs from the wall to this jack,

according to one of the diagrams shown to

the right.

Plug in the TV. The LCD-TV is designed to

operate on DC power.

Once all external connections are complete,

go to page 19 to run Auto Program.

1

2

3

4

PAGE 11

206-3898

Cable Service Hookup

Connect cable service to the

LCD TV/Monitor

Locate the Antenna/Cable jack on the

back of the TV.

Connect the cable wire to the

Antenna/Cable jack according to one

of the diagrams to the right.

Plug in the TV. The LCD-TV is designed

to operate on DC power.

After all external connections are

complete, go to page 19 to run Auto

Program.

1

2

3

4

Cable TV

Wall Jack

RF Coaxial Wire

(75ohm)

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

Cable TV

Wall Jack

Cable Box

In

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

For cable box operation, leave the

television tuned to channel three or four

and use the cable box to change channels.

PAGE 12

206-3898

Antenna & VCR Hookup

Connect antenna and a VCR to the LCD-TV

Locate the Antenna/Cable jack on

the back of the VCR.

Connect the antenna wire that runs

from the wall jack to the VCR.

Connect other wires according to

the diagram to the right.

Plug in the TV. The LCD-TV is

designed to operate on DC power.

After all external connections are

complete, go to page 19 to run

Auto Program.

1

2

3

4

Round

Or

Flat wire

(300 ohm)

300/75 ohm

Adapter

Antenna

In

Out

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

L - Audio - R

206-3898

PAGE 13

For cable box operation, leave the VCR

and the television tuned to channel

three or four and use the cable box to

change channels.

Cable Service w/VCR Hookup

Connect cable service and a VCR to the LCD TV/Monitor

Locate the Antenna/Cable jack on the

back of the VCR.

Connect the cable service wire to the VCR.

Connect other wires according to the dia-

gram to the right.

Plug in the TV. The LCD-TV is designed to

operate on DC power.

After all external connections are com-

plete, go to page 19 to run Auto Program.

1

2

3

4

In

Out

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

Cable TV

Wall Jack

Cable Box

In

Out

3 4

output

switch

Cable TV

Wall Jack

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

L - Audio - R

PAGE 14

206-3824

DC Power Hookup

Connect the TV to DC power directly or use the optional AC/DC power converter

12 Volt DC Power Hookup

The LCD-TV is designed to operate on 12V DC

power.

Locate the DC input on the back of the

LCD TV/Monitor.

Insert the DC power supply connector into

the DC in port on the TV as shown to the

right.

After all connections have been made. Go to

page 19 to run Auto Program.

1

2

3

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

IN

Optional

AC to DC

Power

Converter

DC

Power

Supply

206-3886

PAGE 15

Front Panel Controls Operation

menu

captions

vol

ch

power

menu

captions

vol

ch

power

C

TV Operation

Press the POWER button to turn the

LCD TV/Monitor on from standby mode.

Use the ch (Channel) button to cycle through the

available channels.

Use the vol (Volume) button to adjust the sound

level to your preference.

Press captions repeatedly to select a closed cap-

tions option or turn Off.

Captions Operation

Use captions to select the closed captions mode:

Off, C1, C2, C3, C4. Typical closed captions

are broadcast on C1, if available on program.

On-Screen Displays

See descriptions on page 17. On-screen displays

will appear when the feature is active or the

function is being used.

Using the front control panel to operate the LCD TV/Monitor

Note: The TV master switch must be set to ‘

I’

for the TV to be in standby mode.

A

B

C

B

A

D

Not

functional

PAGE 16

206-3898

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic operational features of the TV

Auto Program 19 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 20 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 21 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Clock Set 22 Sets the time.

Timer 23 Sets times for the TV to turn itself on and off each day.

Caption/Text 24 Chooses a captioning or text option.

Language 25 Picks the language the on-screen menus will appear in.

AUDIO MENU 26 Customizes the sound. Options are:

Bass, Treble, Balance, Audio Mode, Front Surround, SoundRite, Speakers.

VIDEO MENU 27 Adjusts the picture appearance. The options are: Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

PARENTAL 28/48 Allows installer/user to block program content for up to 12 hours, with the use of a password.

CONTROL MENU

17 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, (or video source), type of incoming audio signal, and XDS* info if provided.

Alarm Sets a time the TV will turn itself on.

Sleep Timer Sets a time the TV will turn off.

Volume Shows current sound level.

Captions Selects Caption/Text options.

Ch Preview Displays the available channels and menus list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS

Installer Menus 34 Makes adjustments to the TV’s operational features.

*XDS (Extended Data Service) Additional program information provided at the discretion of the

broadcaster. May include: title of broadcast, elapsed time, and time remaining on program.

Descriptions of the menus and on-screen displays available to the installer

Menu Name Page Description

206-3824

PAGE 17

Other Menus & On-Screen Displays

PRESS DIGITS TO SET TIME

TIMER TO SELECT AM/PM

ALARM MENU

TIME NOW 3:11 PM

TIMER

6:10 AM

TIMER

CHANNEL PREVIEW•

5 - - - -

9 - - - -

20 - - - -

32 - - - -

44 - - - -

AUX - - - -

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

VOLUME•

Press the remote keys indicated below to access these menus and displays

CHANNEL BANK

BANK 3

CAPTION 1 IS ON

CC

Sleep Timer Menu

Press TIMER. Sets a time to auto-

matically turn the TV off and shows

remaining time before TV shutoff.

Volume Display

Press VOLUME. Shows currently

selected sound setting.

Alarm Menu

Press ALARM. Sets a time the TV

will turn itself on.

Ch Preview Menu

Press CH PREVIEW. Displays list of

the available TV Channels, Guest

Parental Control menu (if active)

and Video Channel access. Press

CHANNEL Up/Down to select a

channel, or menu, then ENTER to go

to channel or menu.

Closed Captions Menu

Press CC. Turns selected option on

or off. See Caption/Text page to

select options.

Channel Banks Menu

Press SOURCE/BANK on an Installer

remote equipped with those keys.

Accesses the Channel Banks menus:

Bank 1, Bank 2, Bank 3, Bank 4.

Ch 25 - PBS

7:15

OLD TIME MOVIES

LENGTH 01:00 TIME LEFT 00:36

Rating:

TV-14

PM

Channel/Time Display

Press ENTER. Shows currently

selected channel or source, current

time if the clock has been set,

incoming audio signal, and XDS

data if provided by broadcaster.

PAGE 18

206-3898

Installer Remote Key Functions

TIMER

CH PREVIEW

ENTER

1

2

3

4

5

6

7

8

9

0

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

CC

MENU

ALARM

ADJ

SELECT

remote control part number

LP702

124-213-04

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

.

CHANNEL (UP/DOWN)

Chooses next available channel.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

TIMER

Press repeatedly to adjust TV turn-off time

from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the optional LP702 installer’s remote and what they do

ALARM

Press to go to the Alarm menu. Set a time

for the TV to turn itself on.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options.

Press MENU repeatedly to scroll through

menus. Use SELECT to choose an option

and ADJ (adjust) Left/Right to change

the selected option.

CHANNEL PREVIEW

Gives installer access to the guest’s

menus. Displays the available TV channels

and hotel guest’s Parental Control menu

(if active). Selects the Video source. (Use

the Audio/Video jacks on the back of the

TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio mode on TVs equipped

with FM radio.

NUMBER KEYPAD

Used to key-in numbers and select chan-

nels directly: key-in channel numbers

and press ENTER to go to new channel

.

206-3898

PAGE 19

Auto Program (Channel Search)

1

2

3

4

5

6

7

TIMER

CH PREVIEW

ENTER

1

2

3

4

5

6

7

8

9

0

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

CC

MENU

ALARM

ADJ

SELECT

3/5

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

TO PROGRAM

4/6

1

7

2

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search

With the optional Installer remote control in hand, press

the POWER key to turn the TV on.

Press MENU repeatedly until the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press the Right or Left ADJ (Adjust) arrow to go to the

Auto Program menu.

Using SELECT, choose CABLE TV or OFF AIR ANTENNA on

the menu. (The highlighted option is selected.)

Press the Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

Mini glossary

OFF-AIR-ANTENNA If the end user can only view over-the-air broadcasts, select Off Air Antenna.

CABLE If you provide cable service to the end user, select Cable TV.

Auto Program finds channels being received by the TV tuner.

Cable will not work unless a cable service is present.

PAGE 20

206-3824

1

2

3

4

Channel Add/Del/Blank Menu

TIMER

CH PREVIEW

ENTER

1

2

3

4

5

6

7

8

9

0

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

CC

MENU

ALARM

ADJ

SELECT

2

1

5

3/4

CH 44 ADDED

TIMER

Fine-tune the user’s channel selection list

Press the MENU key repeatedly on the Installer’s remote

until the Setup menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk

option.

Using either the NUMBER keypad and ENTER or the

Channel Up/Down arrow on the remote, select a channel.

(If adding a deleted channel, you will need to use the

NUMBER keypad and ENTER.)

Using the Right/Left ADJ arrow, specify whether that

channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 4.

When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, to the Channel

Preview List

Go to the Setup menu, select the Add/Del/Blnk option.

Use Channel Up/Down to select the option and choose

Added.

Note: If the option was turned off in the Service menu,

you will have to reinstate it before it can appear as an

option in the Channel Preview list.

Note: You can specify Add, Delete or Blank for VCR3,

VCR4, and Aux. Caution: If you delete CH3, VCR3 is also

deleted, if you delete CH4, VCR4 is also deleted and vice

versa.

If you delete a channel, it isn’t gone for good. Just select it using

the NUMBER keypad on the remote, or add it later.

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

5

La pagina sta caricando ...

Zenith L10V34H Installation And Setup Manual

Questo manuale è adatto anche per

Zenith L10V34H Installation And Setup Manual

in altre lingue

Documenti correlati

Altri documenti