Yamaha GW33 Manuale del proprietario

Categoria
Amplificatore per strumenti musicali
Tipo
Manuale del proprietario
GUITAR PERFORMANCE EFFECTOR
GUITAR PERFORMANCE EFFECTOR
OWNER’S MANUAL
This product utilizes batteries or an external
power supply (adapter). DO NOTconnect this
product to any power supply or adapter other than
one described in the manual, on the name pIate,
or specifically recommended by Yamaha.
This Product should be used only with the compo-
nents supplied or; a cart, rack, or stand that is
recommended by Yamaha. If a cart, etc., is used,
please observe all safety markings and instruc-
tions that accompany the accessory product.
SPEClFlCATIONS SUBJECT TO CHANGE:
The information contained in this manual is
believed to be correct at the time of printing.
However, Yamaha reserves the right to change or
modify any of the specifications without notice or
obligation to update existing units.
This product, either aIone or in combination with
an amplifier and headphones or speaker/s, may
be capable of producing sound levels that could
cause permanent hearing loss. DO NOT operate
for Iong periods of time at a high volume level or
at a level that is uncomfortabIe. lf you experience
any hearing Ioss or ringing in the ears, you
should consult an audiologist. lMPORTANT: The
louder the sound, the shorter the time period
before damage occurs.
NOTlCE:
Service charges incurred due to Iack of knowl-
edge relating to how a function or effect
works(when the unit is operating as designed)are
not covered by the manufacturers warranty, and
are therefore the owners responsibility. Please
study this manual carefulIy and consult your
dealer before requesting service.
ENVIRONMENTAL lSSUES:
Yamaha strives to produce products that are both
user safe and environmentalIy friendIy. We
sincerely believe that our products and the
production methods used to produce them, meet
these goals . ln keeping with both the letter and
the spirit of the law, we want you to be aware of
the following:
Battery Notice: This product MAY contain a
small non-rechargeable battery which (if
applicabIe)is soldered in PIace. The average life
span of this type of battery is approximately five
years. When repIacement becomes necessary,
contact a qualified service representative to
perform the replacement.
This Product may also use householdtype
batteries. Some of these may be rechargeable.
Make sure that the battery being charged is a
rechargeable type and that the charger is in-
tended for the battery being charged.
When installing batteries, do not mix old batteries
with new, or with batteries of a different type.
Batteries MUST be installed correctly. Mismatches
or incorrect instalIation may result in overheating
and battery case rupture.
Warning: Do not attempt to disassemble, or
incinerate any battery. Keep alI batteries away
from chiIdren. Dispose of used batteries promptly
and as regulated by the laws in your area.
Note: Check with any retailer of household type
batteries in your area for battery disposal informa-
tion.
Disposal Notice: Should this Product become
damaged beyond repair, or for some reason its
useful life is considered to be at an end, pIease
observe aII IocaI, state, and federaI regulations
that relate to the disposal of products that contain
lead, batteries, plastics, etc. if your dealer is
unable to assist you, Please contact Yamaha
directly.
NAME PLATE LOCATlON:
The name Plate is located on the bottom of the
product. The model number, serial number, power
requirements, etc., are located on this plate. You
should record the seriaI number and the date of
purchase in the spaces provided beIow and retain
this manual as a permanent record of your
purchase.
Model GW33
Serial No.
Purchase Date
SPECIAL MESSAGE SECTION (USA)
PLEASE KEEP THIS MANUAL
92-BP
AURAL EXCITER
®
is a registered trademark and is manufactured under license from Aphex Systems, Ltd.
1
You are probably eager to try out your new GW33 right
away and hear what it can do, rather than have to read
through a lot of instructions before you can even get a
sound out of it.
Before you do anything else, however, you should read the
PRECAUTIONS
section (page 3). This tells you briefly
how to care for your new GW33, how to avoid damaging
it, and how to ensure long-term, reliable operation.
Next, read the
GW33 SYSTEM OVERVIEW
(page 7).
This provides an important introduction to the internal
organization of the GW33, enabling you to better under-
stand its various functions and use the device to its full
potential.
To actually start using the GW33, read the
GUIDED
TOUR
(page 10). It guides you step-by-step in setting up
your GW33, connecting it properly, and (most impor-
tantly!) getting sound out of it. The section also intro-
duces you to the effect programs by letting you hear what
they are capable of, and explains how to use some of the
other main functions of the device.
The
REFERENCE
section (page 16), on the other hand,
is a comprehensive guide to all functions. You won’t need
(or want) to read through all of it at once, but it is there for
you to refer to when you need information about a certain
feature or function.
The
PANEL CONTROLS AND TERMINALS
(page 4)
is also mainly for reference. In general, look through this
section to familiarize yourself with the controls, and refer
to it when necessary.
The
INDEX
in the
APPENDIX
section (page 40) is also
very helpful. It lists page numbers for virtually every
function, feature, control and terminal found on the
GW33, and lets you find the information you need quickly
and easily.
Other parts of the
APPENDIX
section (page 36) provide
additional useful information: lists of the effect programs
of the GW33, tips on troubleshooting (when something
doesn’t work as expected), and other important informa-
tion.
( READ THIS FIRST!!)
Congratulations and thank you for purchasing the Yamaha GW33 Guitar Performance Effector!
The GW33 is a portable and convenient multi-effect device designed especially for guitar. The comprehen-
sive variety of high-quality effects and convenient Pedal Switch control functions make the highly portable
GW33 ideal for signal processing in home recording, studio, and live performance applications.
Some of the advanced features of the GW33 include:
Eight independent effect blocks, including Compressor, Distortion/Insert, Equalizer/Amp Simula-
tor, Modulation 1/2, Delay, Reverb, and Noise Gate. The two Modulation blocks allow you to have
two different modulation effects simultaneously.
A wide variety of high-quality distortion effects, utilizing both analog and digital distortion circuits.
Twenty-five professionally created Preset effect programs, for use in a wide variety of processing
applications, plus twenty-five User memory locations for saving your own effect programs.
A separate send/return loop (Insert) for integrating external effects into the GW33 effect chain.
Convenient parameter control over all effects, yet exceptional ease-of-use — you can adjust the
parameters of the effect blocks much as you would on conventional pedal effects.
Consistent, continuous Delay/Reverb decay, letting you switch between similarly set programs
without cutting off the Delay/Reverb sound.
Foot Controller input, for connection of an optional FC7 Foot Controller, giving you convenient
volume control as well as realtime adjustment of the Pedal Wah effect.
Built-in tuner, allowing you to tune your instrument without removing it from the signal chain.
Built-in metronome, with fully adjustable time signature and tempo. The metronome provides both
visual indication and an audio click for maximum flexibility.
2
HOW TO USE THIS MANUAL (READ THIS FIRST!!) . . . . . . . . . . . . . . . . . . . . . . 1
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
PANEL CONTROLS AND TERMINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GW33 SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GW33 Internal Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
The Effects of the GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
The Effect Structure of the GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Memory Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Effect Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SETTING UP AND PLAYING YOUR GW33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PLAYING WITH THE EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EDITING AN EFFECT PROGRAM AND SAVING IT . . . . . . . . . . . . . . . . . . . . . 13
Editing an Effect Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Comparing the Edited Effect Program with the Original . . . . . . . . . . . . . . . . . . 14
Saving an Effect Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SELECTING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TURNING ALL EFFECTS OFF — BYPASS FUNCTION . . . . . . . . . . . . . . . . . . . 17
TURNING EFFECT BLOCKS ON AND OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
EDITING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Compare Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Parameter Check Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Checking Parameter Values in the Play Mode . . . . . . . . . . . . . . . . . . . . 19
EFFECTS AND PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Compressor Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Distortion/Insert Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Equalizer/Amp Simulator (EQ/AMP) Block . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Amp Simulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Modulation (MOD) 1 and 2 Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chorus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Phaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Pitch Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Detune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
AURAL EXCITER
®
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Touch Wah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pedal Wah . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Delay Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Reverb Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Noise Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
FOOT CONTROLLER OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting the Volume Position and Minimum Volume . . . . . . . . . . . . . . . . . . . . . 30
Using the Foot Controller for Pedal Wah Control . . . . . . . . . . . . . . . . . . . . . . . 30
TOTAL LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SAVING EFFECT PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
COPY AND SWAP OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Copying One Effect Program to Another Program Number . . . . . . . . . . . . . . . 32
Swapping One Effect Program with Another . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Restoring Factory-set Effect Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TUNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Tuning the Pitch of the Connected Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Changing the Standard Pitch of the Tuner Function . . . . . . . . . . . . . . . . . . . . . . 35
METRONOME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
BLANK EFFECT PARAMETER CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3
USE THE CORRECT POWER SUPPLY
Power to the GW33 should be supplied only from the
appropriate Yamaha AC adaptor (the PA-3, or another
adaptor recommended by Yamaha). Use of another
adaptor may cause serious damage to the unit. (Never use
the PA-3B.) Also make sure that the adaptor you have is
appropriate for the AC mains supply voltage in the area
where you intend to use the GW33. (The correct input
voltage is marked on the adaptor.)
AVOID EXCESSIVE HEAT, HUMIDITY, DUST
AND VIBRATION
Keep the unit away from locations where it is likely to be
exposed to high temperatures (such as direct sunlight) or
humidity. Also avoid locations which are subject to
excessive dust accumulation or vibration which could
cause mechanical damage.
AVOID PHYSICAL SHOCKS
Although the GW33 has been constructed to withstand the
normal rigors of stage and studio use for optimum sturdi-
ness and reliability, avoid subjecting it to strong physical
shocks (such as dropping or hitting it), since this may
damage the unit. Since the GW33 is a precision-made
electronic device, also avoid applying excessive force to
the various controls.
DO NOT OPEN THE CASE OR ATTEMPT
REPAIRS OR MODIFICATIONS YOURSELF
This product contains no user-serviceable parts. Refer all
maintenance to qualified Yamaha service personnel.
Opening the case and/or tampering in any way with the
internal circuitry will void the warranty.
MAKE SURE POWER IS OFF BEFORE MAK-
ING OR REMOVING CONNECTIONS
Always turn the power off prior to connecting or discon-
necting cables.
HANDLE ALL CONNECTIONS CAREFULLY
Always be careful to connect and disconnect all cables and
cords by gripping the connector itself, not by pulling on
the cord.
CLEAN WITH A SOFT, DRY CLOTH
Never use solvents such as benzine or thinner to clean the
unit, since these will damage the finish. Wipe clean with a
soft, dry cloth. If necessary, use a soft, clean slightly
moistened cloth — making sure to wipe the case off again
with a dry cloth.
ELECTRICAL INTERFERENCE
Since the GW33 contains digital circuitry, it may cause
interference and noise if placed too close to TV sets,
radios or similar equipment. If such a problem occurs,
move the GW33 further away from the affected equip-
ment.
4
This section shows and explains all of the controls and terminals of the GW33. Since the expla-
nations below are fairly brief, you should turn to the page references given for more information
on individual buttons and features. Refer to this section also as necessary when using the GW33,
when you need specific information on a certain control or terminal.
TOP PANEL
•••••••••••••••••••••••••••••••••••••••••••••••••
•••••••
COMP
DIST /
INSERT
EQ / AMP
DELAY
REVERB
N.GATE/UTIL
TUNER/
METRONOME
MOD 2
MOD 1
ATTACK
PRE-DRIVE*
LOW /
TIME
TIME
THRESHOLD
SPEED
PITCH
/
PITCH L
ENHANCE
/
SENSE
SENSE
DRIVE
MID /
FB
TONE
VOLUME POSITION
BEAT
(14~88 = 1/4~8/8)
DEPTH
/ PITCH R
FREQUENCY
TONE
HIGH / TONE
MIX
MIX
MINIMUM VOLUME
TEMPO
(60~86.=60~186)
TONE / FB
MIX
MIX / RANGE
LEVEL
LEVEL
LEVEL
TOTAL LEVEL
CLICK LEVEL
(1 LO 2 MID 3 HI)
ON/OFF
(SWITCH 4)
1 EQ / 2 STACK 3 COMBO 4 TUBE
————---
1~3
OD, DIST1,2 (DI*+AN)
4,5 OD*+DIST1,2
6~11 OD, DIST1,2+INSERT 12 INSERT
————---
————---
TUNING PITCH
(0~5
=
440~445Hz)
1 CHORUS / 2 FLANGER 3 PHASER
4 PITCH SHIFT / 5 DETUNE
6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH
1 HALL 2 ROOM 3 STAGE 4 PLATE
ON/OFF
(SWITCH 5)
ABCDE
COPY / SWAP / WRITE
MEMORY NO.
NO
TUNER
20
5
+ 5
0
+20
PLAY
COPY
SWAP/
WRITE
EDIT/
COMPARE
METRONOME
••••
PITCH SHIFT
±1 = 3rd
±2 = 3rd
±3 = 4th
±4 = 5th
±5 = 5th
±6 = 6th
±7 = 7th
±8 =
OCTAVE
DELAY TIME
10 ~ 90 =
10 ~ 90ms
10.~ 81.=
100 ~ 810ms
ON / OFF
1 EFFECT OFF
2 EFFECT ON
3 SWITCH
VOLUME POSITION
1 DIST
2 DELAY
3 REVERB
4 REVERB
DISTORTION / INSERT
1 OVERDRIVE
2 DISTORTION
1
3 DISTORTION
2
OD
INSERT
DS
1INSERT
DS
2INSERT
INSERTOD
INSERTDS
1
INSERTDS
2
4 OD + DIST
1
5 OD + DIST
2
12 INSERT
COMPRESSOR DIST / INSERT EQ / AMP MOD 1 MOD 2 DELAY REVERB
TUNER
HOLD
GUITAR PERFORMANCE EFFECTOR
YES
BANK MEMORY
••••
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•••
••••••
••••••
••
••••
••
••••
BYPASS
••
••••
••
••••
6
7
8
9
10
11
TWIN DRIVE OVERDRIVE & DISTORTION
DUAL MODULATION WITH AURAL EXCITER
INTEGRATED INSERTION LOOP
BUILT-IN TUNER & METRONOME
ON OFF
••••••••••••••••••••••
PARAM
CHECK
ewq r t y
u
i
o !1!0 !2
q COPY, SWAP/WRITE Buttons
These two buttons call up the Copy and Swap/Write
operations, respectively. (See pages 32 and 33.) Copy
and Swap are called up from the Play mode, while
Write is called up from the Edit mode. The COPY and
SWAP/WRITE lamps are lit when the respective Copy
or Swap/Write operation is active.
When pressed together simultaneously, these buttons
start the built-in Metronome function. When the
Metronome is on, the lamps of the two buttons flash in
time with the audio click. (See page 35.)
w PLAY Button
Enables the Play mode, from which the effect programs
can be selected and played.
e BANK/MEMORY Indicator
Displays the program number. During Tuner operation,
this displays the name of the note or string played. (See
page 34.) The LED dot (#) at the bottom right serves as
a sharp indicator during Tuner operation (functioning
along with the note name shown in the BANK/
MEMORY indicator), and lights to indicate values of
100 and higher.
5
r EDIT/COMPARE Button
For enabling the Edit mode, from which the selected
effect program can be edited. In the Edit mode, this
also serves as a Compare switch for toggling between
the newly edited settings and original settings of an
effect program.
t Effect Parameter/Tuner Lamps
In the Edit mode:
These indicate the effect block and
parameters currently selected for editing. (See
page 13.)
In the Play mode:
These indicate the effect block
currently selected for checking parameter
values. (See page 19.)
In the Tuner mode:
These indicate whether the input
signal is in tune or not; when the center lamp (to
the right of 0) flashes, the signal is in tune. (See
page 34.)
y YES/ and NO/ Buttons
In the Edit mode:
These are used to select an effect
block (and its parameters) for editing. (See page
13.)
When pressed together (in the Edit mode):
These call
up the Parameter Check mode, for checking the
currently edited parameter values. (See page
19.) Pressing one of the buttons again returns to
normal editing.
In the Play mode:
These are used to select the effect
block for checking parameter values. (See page
19.)
In the Copy, Swap and Write operations:
These are
used to execute (YES) or cancel (NO) the
respective operation.
u TUNER Button
For enabling the Tuner mode (from the Play mode).
(See page 34.) Pressing the button again returns to the
Play mode.
i Effect Block ON/OFF Lamps
These light when the corresponding effect block is on.
o Pedal Switches 1 – 5
In the Play mode:
When the ON/OFF lamp (above
Pedal Switch B) is off, these are used to select
effect programs. (See page 12.)
In the Edit or Play modes:
When the ON/OFF lamp
(above Pedal Switch B) is flashing, these are
used to turn individual effect blocks on or off.
(See page 17.)
Also, pressing Pedal Switches 1 and 2 together simulta-
neously enables the Tuner mode. (See page 34.)
Pressing Pedal Switches 2 and 3 together simulta-
neously enables the Bypass function. (See page 17.)
!0 Parameter Dials
For selecting the effect type and adjusting the param-
eters of a selected effect. The parameters in a single
column correspond to the dial in that column.
!1 Pedal Switch B (Bank)
In the Play mode:
Pressing this once enables selection
of banks 1 – 5. Holding this down enables
selection of banks 6 – 0.
Pressing this twice quickly enables effect block on/off
switching. (See page 17.)
!2 ON/OFF Mode Lamp
This flashes to indicate that Pedal Switches 1 – 5 can be
used to turn individual effect blocks on or off.
6
REAR PANEL
POWER
ON OFF DC IN INPUT SEND RETURN
INSERT
R
OUTPUT
L / MONO
PHONES
FOOT
CONTROLLER
q w e r y ut
q POWER ON/OFF Switch
w DC IN Terminal
For connection to the PA-3 AC adaptor (or another
adaptor recommended by Yamaha). (Never use the
PA-3B.) Wrap the adaptor cord firmly around the cable
clip as shown, to prevent accidental unplugging of the
power cord during use.
t L/MONO and R OUTPUT Jacks
For stereo or mono output of the instrument and metro-
nome sound. Connect both of these to the corresponding
left and right channels of your stereo amplification system
to take full advantage of the stereo effects of the GW33.
For mono operation, connect your system only to the L/
MONO jack; this provides a mono mix of the instrument
sound when the R OUTPUT jack is not connected.
y PHONES Jack
For stereo output of the guitar/effect and metronome
sound to a set of stereo headphones.
u FOOT CONTROLLER Jack
For connection of an optional foot controller (use ONLY
the Yamaha FC7), for controlling the volume or the Pedal
Wah effect. (See page 30.)
AC adaptor
Cable clip
DC IN
e INPUT Jack
For connection of an instrument (guitar, bass, etc.). (See
page 10 for more information on input/output connec-
tions.)
r INSERT SEND and RETURN Jacks
For connection of an external effect device or devices.
Use the SEND jack to output the signal from the GW33,
and use RETURN to input the signal from the external
effect device(s).
7
This section provides a brief overview of the GW33 — the basic structure of its various functions
and the memory system. Once you gain a general understanding of the internal workings of the
GW33 as given here, you’ll have the tools for taking full advantage of its features.
The diagram below shows the internal system of the
effects and other functions of the GW33.
The GW33 is equipped with a comprehensive set of
effects designed specifically for the guitar player. Up to
eight different effects can be used simultaneously. More-
over, a special Insert block lets you connect additional
external effect units to the multi-effect chain of the GW33.
Individual effects (excepting Noise Gate) can be turned on
and off as needed with the Pedal Switches and can be
quickly and easily adjusted with the Parameter Dials.
There are eight main effect blocks and a total of thirty-one
different effect types:
(Refer to the EFFECTS AND PARAMETERS section,
page 20, for more detailed descriptions and explanations
of these effects.)
With all these various effects, used individually or simul-
taneously, the GW33 has all you need to augment your
sound, whatever the application. Plus, flexible effect
bypass (on/off) functions give you even more realtime
control over the sound. A programmable Noise Gate is
also included for filtering out hum, hiss and other undesir-
able noise. (See page 29.)
The Effects of the GW33
Effect Block
Compressor
Distortion/Insert
Equalizer/
Amp Simulator
Modulation 1
Modulation 2
Delay
Reverb
Noise Gate
Effect Type
Compressor
Overdrive, Distortion 1,
Distortion 2, Overdrive + Distortion 1,
Overdrive + Distortion 2, Overdrive Insert,
Distortion 1 Insert, Distortion 2 Insert,
Insert Overdrive, Insert Distortion 1,
Insert Distortion 2, Insert
Equalizer, Stack Amp Simulator,
Combo Amp Simulator, Tube Amp Simulator
Chorus, Flanger, Phaser, Pitch Shift,
Detune, Exciter, Touch Wah, Pedal Wah
(Same as Modulation 1; effects can be used
independently.)
Delay
Hall, Room, Stage, Plate
Noise Gate
GW33 Internal Structure
* Use the optional YAMAHA Foot Controller FC7.
INPUT
INSERT
SEND
INSERT
INSERT
RETURN
WAH
COMP
DIST /
INSERT
N.GATE EQ / AMP DELAY MOD 1 REVERB
OUTPUT
L/MONO
MOD 2
R
TOTAL
LEVEL
CLICK
LEVEL
TUNER
BYPASS
METRONOME
Volume
Pedal
(Position 2)
Volume
Pedal
(Position 1)
Volume
Pedal
(Position 3)
Volume
Pedal
(Position 4)
(when
Touch Wah
or Pedal
Wah is
selected)
MOD 1, 2 Block
Headphones
Wah
Pedal
8
The Effect Structure of the GW33
Keep in mind as you use the GW33 that the structure of its
effects is basically in a four-part hierarchy: 1) Effect
programs, 2) Effect blocks, 3) Effect types, and 4) Effect
parameters.
An effect program consists of eight different effect blocks,
all of which can be used simultaneously. A block includes
one or more effect types, one of which can be used at a
time. And each effect type has up to four different param-
eters, which allow you to set the sound of the effect. The
logic of this structure is reflected in the panel layout, with
effect blocks, types and parameters printed in a matrix
from left to right.
Memory Structure
The GW33 has a total of 50 effect programs, divided into
ten banks of five programs each. The 25 programs from
61 – 05 are Preset programs. Programs 11 – 55 are User
programs, and your own original settings can be stored to
these.
•••••••••••••••••••••••••••••••••••••••••••••••••
COMP
DIST /
INSERT
EQ / AMP
DELAY
REVERB
N.GATE/UTIL
TUNER/
METRONOME
MOD 2
MOD 1
ATTACK
PRE-DRIVE*
LOW /
TIME
TIME
THRESHOLD
SPEED
PITCH
/
PITCH L
ENHANCE
/
SENSE
SENSE
DRIVE
MID /
FB
TONE
VOLUME POSITION
BEAT
(14~88 = 1/4~8/8)
DEPTH
/ PITCH R
FREQUENCY
TONE
HIGH / TONE
MIX
MIX
MINIMUM VOLUME
TEMPO
(60~86.=60~186)
TONE / FB
MIX
MIX / RANGE
LEVEL
LEVEL
LEVEL
TOTAL LEVEL
CLICK LEVEL
(1 LO 2 MID 3 HI)
ON/OFF
(SWITCH 4)
1 EQ / 2 STACK 3 COMBO 4 TUBE
————---
1~3
OD, DIST1,2 (DI*+AN)
4,5 OD*+DIST1,2
6~11 OD, DIST1,2+INSERT 12 INSERT
————---
————---
TUNING PITCH
(0~5
=
440~445Hz)
1 CHORUS / 2 FLANGER 3 PHASER
4 PITCH SHIFT / 5 DETUNE
6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH
1 HALL 2 ROOM 3 STAGE 4 PLATE
ON/OFF
(SWITCH 5)
ABCDE
COPY / SWAP / WRITE
MEMORY NO.
NO
YES
•••••
••••••
••••••
••••••••••••••••••••••
PARAM
CHECK
Effect Block
These are used to
select the effect
block.
This is used to
select the
effect type.
These are used to change the
parameters in the corresponding
columns.
Effect Types
Effect Parameters
Preset Programs
Bank 6 Bank 7 Bank 8 Bank 9 Bank 0
65
64
63
62
61
75
74
73
72
71
85
84
83
82
81
95
94
93
92
91
05
04
03
02
01
User Programs
Bank 1 Bank 2 Bank 3 Bank 4 Bank 5
15
14
13
12
11
25
24
23
22
21
35
34
33
32
31
45
44
43
42
41
55
54
53
52
51
9
Sound Character
Main Sub
Effect Programs
Sound Character
Main Sub
61
62
63
64
65
71
72
73
74
75
81
82
83
84
85
91
92
93
94
95
01
02
03
04
05
11
12
13
14
15
21
22
23
24
25
31
32
33
34
35
41
42
43
44
45
51
52
53
54
55
#
Programmer’s comments
#
Programmer’s comments
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Over
Drive
Dist
Hard
Dist
Softer
Clean
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Hard
Dist
Softer
Over
Drive
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Hard
Over
Drive
Clean
Clean
Dist
Hard
Dist
Softer
Clean
S.E.
S.E.
Detune
Detune
Flanger
Chorus
Wah
Chorus
Detune
Phaser
Detune
Detune
Phaser
Flanger
Detune
Detune
Touch
Wah
Detune
Chorus
Detune
Chorus
Detune
Touch
Wah
Pitch
Detune
Chorus
Detune
Flanger
Phaser
Detune
Detune
Detune
Chorus
Pitch
Pedal
Wah
Detune
Pedal Wah
Flanger
Touch Wah
Chorus
Phaser
Digital and analog distortion for rock
solos.
Analog overdrive + distortion; good
for pop music.
Natural overdrive for rock’n’roll.
Clean sound, good for wide range of
styles (ex., blues, funk, jazz).
Clear sound with flanger and chorus.
Heavy distortion sound with en-
hanced low and high frequencies.
Distortion sound for backing.
Spacious overdrive sound for fusion.
Natural reverb sound from the 50’s.
Dynamics “squashed” with compression.
Tremolo sound.
Digital + analog overdrive for rock
or fusion.
Powerful sound, good for rock
ballads.
Overdrive sound for rock leads.
Mellow, round sound.
Clean sound for rhythmic play.
Hard distortion sound with enhanced
attack; for rock leads.
Distortion sound with detuning, for
rock backing.
“Dry” overdrive.
Multi-purpose program for a wide
variety of styles.
Touch Wah program, good for funk,
jazz, blues, etc.
Hard digital + analog distortion
sound for direct recording.
Hard distortion program, with stack
amp sound, for direct recording.
Warm overdrive sound for direct
recording.
Clear, distinct sound with detuning
and delay, for direct recording.
Clean sound for direct recording.
Distortion especially for rock solos.
Digital + analog distortion, plus EQ,
for heavy metal.
Detune and reverb for a “wet” solo
sound.
Natural, warm overdrive.
Clean, spacious sound with Cho./
Detune/Delay/Reverb mix.
Hard, metallic lead.
Dynamically responds to your
plucking technique.
Stereo pitch shift: 5th above and
below.
Clean and dreamy with long delay.
Soft, clean sound, ideal for soloing or
rhythmic chords.
Analog overdrive + distortion —
hard-edged for backing.
Analog + digital distortion, plus
flanger and delay.
Bright overdrive with delay for
American hard rock leads.
British 60’s rock sound — simple
and straight.
70’s fusion sound, with heavy
phaser.
Hard distortion for rock soloing.
Slightly bright distortion for hard
rock backing.
Crunch sound with enhanced low
and high frequencies.
Good, clear sound for rhythmic
playing.
Ideal for funky rhythmic playing or
arpeggios.
Hard distortion sound, with pitch an
octave below.
Hard crunch sound for rhythmic
playing; with Pedal Wah.
Mellow sound for rhythmic play.
Sound effect with dynamic response
to plucking technique.
Chorus sound with stereo phaser.
10
Once you’ve taken your GW33 out of the box and are ready to use it, you’ll have to make a few
connections and follow some simple instructions on setting it up.
GUIDED TOUR
When using your GW33 for the first time, read through this short section of the
manual. It guides you step-by-step in all basic operations: setting the instrument
up, connecting it properly to other equipment, and playing the effect programs.
POWER
ON OFF DC IN INPUT SEND RETURN
INSERT
R
OUTPUT
L / MONO
PHONES
FOOT
CONTROLLER
OUT IN
D
C
IN
Plug into a
suitable AC
outlet
PA-3
power adaptor
Use only this
adaptor or
another Yamaha
recommended
adaptor.
Wrap the adaptor cord around the
cable clip to prevent accidintal
unplugging.
Electric guitar
Optional FC7
Foot Controller
(for Volume pedal
and Pedal Wah
control).
External effect unit
Guitar amplifier
(left channel)
Guitar amplifier
(right channel)
Headphones
Signals are output through
the OUTPUT jacks, even
when headphones are
connected.
Adjust the headphone
volume with the Total Level
parameter (see page 31).
When using a single guitar amp, connect to
the L/MONO OUTPUT jack.
*
*
*
11
1
First, make sure that the power switch on the GW33
is off before making ANY connections.
2
Plug the DC output cable from the supplied PA-3
adaptor (or another adaptor recommended by
Yamaha) (Never use the PA-3B.) into the DC IN
terminal on the rear panel, then plug the adaptor into
a convenient AC outlet.
The cable clip located next to this terminal helps to
prevent accidental unplugging of the power supply
during use. Wrap the adaptor cord firmly around the
clip (see the Rear Panel illustration, page 10).
CAUTION!
Do not attempt to use a different
AC adaptor with the GW33. (See the precaution
on page 3.)
3
Plug your instrument into the INPUT jack on the rear
panel.
For the sake of these instructions, we’ll assume
you’re using an electric guitar; however, most any
electronic instrument can be used.
NOTE
You should be careful if you are connecting
a synthesizer or electronic keyboard. Since their
output level is generally much higher than that of a
guitar, the volume control on the instrument should
be turned down accordingly.
4
Connect the GW33 output or outputs to your ampli-
fier/speaker system, as shown on page 10. Before
you do this, however, make sure that the power on
the system is first turned off and all volume controls
are set to zero — this includes the guitar controls and
the volume on the connected amp(s).
NOTE
Use the clean channel of the amplifier for
best results.
5
If you are using an optional FC7 Foot Controller
with the GW33, connect it to the FOOT CONTROL-
LER input jack on the rear panel. Make sure that the
pedal is at or near the maximum position.
6
Turn on the power of all the equipment, starting with
the GW33, and turning on the connected amplifier
last.
7
Before you turn up the volume and try to play, set all
the effects to off by using the Bypass function.
To do this, simultaneously press and hold down
Pedal Switches 2 and 3. Keep holding them down
(for roughly one second) until “bP” (Bypass)
appears in the BANK/MEMORY indicator.
This temporarily turns off all effect processing, and
lets you hear the “dry” input signal.
8
Now, set your guitar to a suitable volume. Next,
slowly bring up the level of the connected amplifier
as you play, until the level is suitable.
9
Finally, turn the Bypass function off by pressing any
one of the Pedal Switches (1 – 5 or B).
If you’ve followed all these instructions carefully,
you should now be able to hear the sound of your
guitar processed by the effects of the GW33, and are
able to try out some of the other effect programs of
the GW33. If no sound is output or the sound isn’t as
you expect, refer to the Troubleshooting section on
page 36.
DIST / INSERT EQ / AMP
BYPASS
••
••••
••
••••
•••••••
BANK MEMORY
Firmly press and hold these
down for about one second.
12
Now that you’ve set up your GW33 and have got sound out of it, let’s try playing with some of
the effects. (If you haven’t already done so, read through the GW33 SYSTEM OVERVIEW
section on page 7 for information on the basic structure of the GW33.)
1
First, make sure that the Play mode is enabled. Press
p.
To change the bank, use the Bank (B) Pedal Switch.
To select one of banks 1 – 5, press it once, then press
the appropriate Pedal Switch 1 – 5.
2
Let’s start with a clean chorus/delay effect. Use
Pedal Switch 5 to select program number 15.
PLAY
DELAY REVERB
•••••••
BANK MEMORY
DIST / INSERT
•••••••
BANK MEMORY
HOLD
ON OFF
Press this once... ...then press one
of these to select
bank 1 5.
1 – 5
To select one of banks 6 – 0, hold the Bank Pedal
Switch down and simultaneously press the appropri-
ate alternate numbered Pedal Switch 6 – 0.
4
Now that you know how to select banks and pro-
grams, try exploring some of the other effect pro-
grams of the GW33. Look through the Effect
Programs list on page 9 for more information about
the programs, and play with a few of them to hear
how they sound.
COMPRESSOR
•••••••
BANK MEMORY
HOLD
ON OFF
While holding
this down...
...press one of
these to select
bank 6 0.
6 – 0
NOTE
If you’re using the FC7 Foot Controller,
make sure that it is at or near the maximum position
to ensure proper volume.
3
Next, try a heavy distortion sound. Press Pedal
Switch 2 to select program number 12.
DIST / INSERT
•••••••
BANK MEMORY
Notice that all the program numbers have two digits.
The first digit indicates the bank and the second
indicates the program number. By pressing one of
the Pedal Switches 1 – 5, you can select one of five
programs in the currently selected bank.
13
The GW33 makes it extremely easy to adjust or change the sound of the effects. In this section,
you’ll learn how to change the effect type and use the Parameter Dials to change effect settings.
You’ll also learn how to compare the edited program with the original. Finally, you’ll learn how
save the new effect program you’ve created.
Editing an Effect Program
1
Select one of the User or Preset effect programs.
Although any effect program will do, select
program number 11 for this example.
NOTE
The on/off switching of the MOD 1/2 and
Delay/Reverb blocks is determined by the On/Off
parameter of those blocks. (See pages 24 and 27.)
4
Use the y and n buttons to select the
desired effect block row (in the parameter matrix
printed on the panel). (The lamp at the left of the
corresponding block lights.) For this example, press
either button repeatedly until the Distortion/Insert
block is selected.
NOTE
Even though creating and saving your own
effect program erases the previously stored program,
you can restore that particular factory Preset pro-
gram. Refer to RESTORING FACTORY-SET
EFFECT PROGRAMS on page 33 for details. Keep
in mind, however, that restoring the factory Preset
program will irretrievably erase the effect you’ve
created. For this reason, you may want to keep a
written record of the settings you make (using a copy
of the Blank Effect Parameter Chart on page 38), so
that you can reprogram the effect later if necessary.
2
Next, press the e button to enable
the Edit mode. (The EDIT/COMPARE lamp
lights and the ON/OFF lamp above the Bank Pedal
Switch flashes.)
•••••••
BANK MEMORY
Press the Bank (B) Pedal Switch once, and press Pedal
Switch 1 to select Bank 1. Then, press Pedal Switch 1
again (if needed) to select program number 11.
HOLD
ON OFF
COMPRESSOR COMPRESSOR
NOTE
The TUNER/METRONOME row cannot be
selected in the Edit mode.
5
Use the Parameter Dials to adjust the effect
parameters. For example, if you want to change the
amount of Pre-drive in the Distortion effect (selected
above), adjust Parameter Dial B.
COMP
DIST /
INSERT
EQ / AMP
MOD 2
MOD 1
1 EQ /
————---
1~3
OD
6~11 OD
1 CHOR
4 PITCH
6 EXCIT
NO
YES
•••••
••••••
••••••
••••••••••••••••••••••
PARAM
CHECK
B
Parameter Dial A is used to change the effect type of
the selected block; BE are used to change the
corresponding parameters.
6
If you wish, you can simply view the parameter
values that you are currently editing (without
changing them) by using the Parameter Check
mode. (See page 19 for details.)
For information about each of the effects and their
parameters, refer to the section EFFECTS AND
PARAMETERS on page 20.
Press this.
EDIT/
COMPARE
Press this to turn Distortion
block on or off. (The lamp
lights when the block is on.)
DIST / INSERT
DIST / INSER
DIST / INSER
ON
OFF
Notice that the ON/OFF lamp above the Bank Pedal
Switch flashes. This means that you can turn indi-
vidual effect blocks on and off.
3
Try turning an effect block on and off now; press
Pedal Switch 2 to turn the Distortion block on or
off.
14
Comparing the Edited Effect Program with the Original
You can compare the sound of the newly edited program
with the sound of the original one. To do this, press the
e button again (so that the EDIT/COM-
PARE lamp flashes).
EDIT/
COMPARE
EDIT/
COMPARE
In this condition, you can hear the sound of the original
effect program. You can also view the original parameter
values by selecting the desired effect block with the
y or n buttons and turning the Parameter
Dials. Doing this doesn’t change the value, it simply
displays it so that you can check it against the value
you’ve edited.
Each press of the e button switches back
and forth between the original program (lamp flashes) and
your new edits (lamp lights continuously).
When you’ve adjusted the sound to your satisfaction, you
may wish to save it for future recall. You can either copy
the settings down on paper (using a copy of the Blank
Effect Parameter Chart on page 38) or go on to the next
section and save the settings to the GW33’s memory.
CAUTION!
Be careful not to press the
p
button while editing. If you do, the original effect
program’s settings will be called up, erasing all
settings you had made to that point.
15
Saving an Effect Program
Now that you’ve created your own original effect pro-
gram, you will want to save the settings to a program
number, so that you can recall your new effect program in
the future. (For more information on saving effect pro-
grams and other matters relating to memory, see the
SYSTEM OVERVIEW section on page 7.)
1
If you’ve continued from the last section and have
new settings you want to save, press the
s button.
The SWAP/WRITE lamp lights and the program
number in the BANK/MEMORY indicator flashes
to indicate that the GW33 is ready to write the
settings to memory at the selected program number.
If you want to save the program to the current
number, skip to step #3. If you want to select a
different program for saving the new program, go to
the next step.
NOTE
Edited programs can be saved to the User
effect programs, in banks 1 – 5. Banks 6 – 0 are
reserved for the Preset effect programs, and cannot
be used to save edited programs.
NOTE
When you’ve edited one of the Preset
programs (61 – 05) and try to save it, “—” appears in
the BANK/MEMORY indicator until you select one of
the User program numbers (11 – 55).
2
If desired, select the destination User program
number (11 – 55) by using Parameter Dial A.
Keep in mind that the programs that you edit can
only be saved to one of the User program numbers,
and not to the Preset program numbers.
3
To actually save the new settings, press the
y button. (Operation returns to the Edit
mode.)
SWAP/
WRITE
SWAP/
WRITE
•••••••
BANK MEMORY
This concludes your short tour of the important functions of the GW33. To find out
more about how to best use your GW33, look through the Reference section and read
about some of the functions that interest you.
A
•••••••
BANK MEMORY
NO
YES
•••••
••••••
••••••
•••••••••••••
PAR
CHE
To cancel the operation without saving, press the
n button.
Pressing n returns to the program that you’ve
been editing. The settings are saved temporarily, and
you can continue editing the program.
NO
YES
•••••
••••••
••••••
••••••••••••••••••••••
PARAM
CHECK
16
OPERATION
1
With the Play mode enabled (press p ), first
select the desired bank of programs.
To select one of banks 1 – 5
To select one of banks 1 – 5, press the Bank Pedal
Switch once, then press the appropriate Pedal Switch 1
– 5.
REFERENCE
This section of the manual explains briefly, yet completely, all of the features and
functions of the GW33. Refer to it when you need information about a specific
feature or function.
2
With the bank now selected, press one of Pedal
Switches 1 – 5 to select the desired program.
Refer to the Effect Programs list on page 9 for more
information on the programs of the GW33.
•••••••
BANK MEMORY
DELAY REVERB
You can continue to select other programs in the same
bank by pressing the other Pedal Switches.
User programs are in banks 1 – 5, and Preset programs
are in banks 6 – 0. Each bank contains five programs.
Preset Programs
Bank 6 Bank 7 Bank 8 Bank 9 Bank 0
65
64
63
62
61
75
74
73
72
71
85
84
83
82
81
95
94
93
92
91
05
04
03
02
01
User Programs
Bank 1 Bank 2 Bank 3 Bank 4 Bank 5
15
14
13
12
11
25
24
23
22
21
35
34
33
32
31
45
44
43
42
41
55
54
53
52
51
To select one of banks 6 – 0
To select one of banks 6 – 0, hold the Bank Pedal
Switch down and simultaneously press the appropriate
alternate numbered Pedal Switch 6 – 0.
•••••••
BANK MEMORY
DIST / INSERT
HOLD
ON OFF
Press this once... ...then press one
of these to select
bank 1 5.
1 – 5
•••••••
BANK MEMORY
COMPRESSOR
HOLD
ON OFF
While holding
this down...
...press one of
these to select
bank 6 0.
6 – 0
17
While playing, you can instantly get a clean, unprocessed sound by using the Bypass function.
This effectively cancels all currently active effects to give you a “dry” sound.
To use the Bypass function:
Simultaneously and firmly press and hold down Pedal
Switches 2 and 3. Keep holding them down (for roughly
one second) until “bP” (Bypass) appears in the BANK/
MEMORY indicator.
Now, when you play your guitar, you should hear the
guitar sound unprocessed by the effects.
NOTE
If a Foot Controller has been connected, it is
also disabled when Bypass is on.
To return to normal Play mode operation and the current
effect program, press any one of Pedal Switches 1 – 5 or
Pedal Switch B.
NOTE
As you press and hold Pedal Switches 2 and 3,
the BANK/MEMORY indicator may briefly show the
program number corresponding to one of those switches.
However, the program you selected before using Bypass
remains selected, and is the one returned to when turning
Bypass off.
DIST / INSERT EQ / AMP
BYPASS
••
••••
••
••••
•••••••
BANK MEMORY
Firmly press and hold these
down for about one second.
In the Play or Edit modes, any of the main effect blocks can be individually turned on or off with
the Pedal Switches. (Switching of Modulation 1/2, and Delay/Reverb is dependent on the On/Off
settings of those effect blocks; see pages 24 and 27.)
OPERATION
1
With the Play mode enabled (press the p
button if necessary), press Pedal Switch B twice
quickly so that the lamp above the Pedal Switch
flashes. This same condition is called up automati-
cally when entering the Edit mode.
2
Press the appropriate Pedal Switch to turn the
desired effect block on or off. (The lamp above the
Pedal Switch lights or goes out accordingly.)
3
To cancel the effect on/off operation and return to
normal effect program selection, press Pedal
Switch B again. (The lamp goes out.)
NOTE
The effect on/off changes that you make here
are temporary. The original on/off settings are re-
stored as soon as you change programs. The on/off
switching of the MOD 1/2 and Delay/Reverb blocks is
determined by the On/Off parameter of those blocks.
(See pages 24 and 27.)
Press this to turn Distortion
block on or off. (The lamp
lights when the block is on.)
DIST / INSERT
DIST / INSER
DIST / INSER
ON
OFF
18
Effect programs can be edited in the Edit mode. Once you’ve edited a program, you can save it
to a User memory location. (See SAVING EFFECT PROGRAMS on page 31.)
CAUTION!
Be careful not to press the
p
button at any time during editing. Doing so
will call up the original effect program’s settings and erase all settings you had made to that
point.
OPERATION
1
Select an effect program for editing and press the
e button to enable the Edit mode.
(The EDIT/COMPARE lamp lights and the ON/OFF
lamp above Pedal Switch B flashes.)
2
Use Pedal Switches 1 – 5 to turn on the desired
effect blocks.
HINT
Since you’ll probably want to listen to the
changes as you make them, make sure that all
relevant effect blocks are turned on. Better yet, turn off
all blocks except the one you are editing. This lets you
clearly hear only the effect you wish to edit. (One
possible exception to this guideline is the Amp Simula-
tor effect, changes to which are easier to hear when
Distortion is also on.)
3
Use the y and n buttons to select the
desired effect block row (in the parameter matrix
printed on the panel). (The lamp at the left of the
corresponding block lights.)
NOTE
The TUNER/METRONOME row cannot be
selected in the Edit mode.
4
Use the Parameter Dials to adjust the effect param-
eters.
Parameter Dial A is used to change the effect type of
the selected block; BE are used to change the
corresponding parameters.
In the example shown below, the EQ/AMP block has
been selected.
•••••••••••••••••••••••••••••••••••••••••••••••••
ABCDE
COPY / SWAP / WRITE
MEMORY NO.
NO
YES
•••••
••••••
••••••
••••••••••••••••••••••
PARAM
CHECK
COMP
DIST /
INSERT
EQ / AMP
DELAY
REVERB
N.GATE/UTIL
TUNER/
METRONOME
MOD 2
MOD 1
ATTACK
PRE-DRIVE*
LOW /
TIME
TIME
THRESHOLD
SPEED
PITCH
/
PITCH L
ENHANCE
/
SENSE
SENSE
DRIVE
MID /
FB
TONE
VOLUME POSITION
BEAT
(14~88 = 1/4~8/8)
DEPTH
/ PITCH R
FREQUENCY
TONE
HIGH / TONE
MIX
MIX
MINIMUM VOLUME
TEMPO
(60~86.=60~186)
TONE / FB
MIX
MIX / RANGE
LEVEL
LEVEL
LEVEL
TOTAL LEVEL
CLICK LEVEL
(1 LO 2 MID 3 HI)
ON/OFF
(SWITCH 4)
1 EQ / 2 STACK 3 COMBO 4 TUBE
————---
1~3
OD, DIST1,2 (DI*+AN)
4,5 OD*+DIST1,2
6~11 OD, DIST1,2+INSERT 12 INSERT
————---
————---
TUNING PITCH
(0~5
=
440~445Hz)
1 CHORUS / 2 FLANGER 3 PHASER
4 PITCH SHIFT / 5 DETUNE
6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH
1 HALL 2 ROOM 3 STAGE 4 PLATE
ON/OFF
(SWITCH 5)
Use these to select
the desired block
for editing. (In this
example, EQ/AMP
is selected.)
Selects the type of
effect. (In this
example, 1 EQ is
selected.)
Adjusts the LOW parameter for the
EQ effect. (The dash indicates that
no parameter is available for the
other effects.)
Adjusts the MID parameter
for the EQ effect. (The dash
indicates that no parameter
is available for the other
effects.)
Adjusts the HIGH
parameter for the EQ effect
and the TONE parameter
for the others.
Adjusts
the LEVEL
parameter.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Yamaha GW33 Manuale del proprietario

Categoria
Amplificatore per strumenti musicali
Tipo
Manuale del proprietario