Pioneer X-CM31-J Manuale del proprietario

X-CM31

-K/-W/-T/-R/-J/-N

CD Receiver System | Micro chaîne CD | Sistema receptor de CD |

CD-Receiversystem | Sistema CD con amplificatore |

CD Receiver System | Система ресивера CD

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’uso

Handleiding

Manual de instrucciones

Инструкции по эксплуатации

Discover the benefits of registering your product online at

http://www.pioneer.co.uk

(or http://www.pioneer.eu).

Découvrez les nombreux avantages offerts en enregistrant

votre produit en ligne maintenant sur

http://www.pioneer.fr

(ou http://www.pioneer.eu).

Bitte nutzen Sie die Möglichkeit zur Registrierung Ihres

Produktes unter

http://www.pioneer.de

(oder

http://www.pioneer.eu)

Registra il tuo prodotto su

http://www.pioneer.it

(o

http://www.pioneer.eu) e scopri subito quali vantaggi puoi

ottenere!

Ontdek nu de voordelen van online registratie! Registreer uw

Pioneer product via

http://www.pioneer.nl -

http://www.pioneer.be

(of http://www.pioneer.eu)

Registre su producto en

http://www.pioneer.es

(o en

http://www.pioneer.eu) Descubra los beneficios de

registrarse on-line:

Зарегистрируйт е Baшe изделие на

http://www.pioneer-rus.ru

(или http://www.pioneer.eu).

Oзнакомьт есь с преимуществами регистрации в Интернет

;&0B6<;(B&RYHUB$QNLIP࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸴᭶㸯㸱᪥ࠉᮌ᭙᪥ࠉ༗ᚋ㸲᫬㸰㸴ศ

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 25 cm at top, 15 cm at rear, and 5 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

CAUTION

The 

STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

plug can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you

have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Loading the batteries in the remote control . . . . . . . . . 5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . 5

02 Part names and functions

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . . . 7

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Top panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

03 Connections

Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . . 11

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

04 Getting started

To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Input function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display brightness control . . . . . . . . . . . . . . . . . . . . . . . 12

Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Muting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

P.bass control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Bass/treble control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . 13

Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . . 14

Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . . . 14

Using the wake-up timer. . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

05 iPod/iPhone/iPad playback

Confirming what iPod/iPhone/iPad models are

supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . . 15

Connecting iPod/iPhone to the top panel . . . . . . . . . . . 16

Connecting iPod/iPhone/iPad using supplied stand . . 16

Watching iPod/iPhone videos on your TV . . . . . . . . . . . 17

Playing iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Playing iPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

06 Disc playback

Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Advanced CD or MP3/WMA disc playback . . . . . . . . . 19

Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programmed play (CD or MP3/WMA) . . . . . . . . . . . . . . 20

About downloading MP3/WMA . . . . . . . . . . . . . . . . . . . 20

About folder playback order . . . . . . . . . . . . . . . . . . . . . . 20

Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 21

Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 21

07 USB playback

Playing USB storage devices . . . . . . . . . . . . . . . . . . . . 22

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specify the folder to play. . . . . . . . . . . . . . . . . . . . . . . . . 23

Switch the display contents . . . . . . . . . . . . . . . . . . . . . . 23

Playing in the desired order

(Programmed Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

08 Using the tuner

Listening to the radio broadcasts . . . . . . . . . . . . . . . . 24

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

To recall a memorised station . . . . . . . . . . . . . . . . . . . . 25

To scan the preset stations. . . . . . . . . . . . . . . . . . . . . . . 25

To erase entire preset memory. . . . . . . . . . . . . . . . . . . . 25

Using the Radio Data System (RDS) . . . . . . . . . . . . . . 25

An introduction to RDS. . . . . . . . . . . . . . . . . . . . . . . . . . 25

Searching for RDS programs. . . . . . . . . . . . . . . . . . . . . 25

Information provided by RDS . . . . . . . . . . . . . . . . . . . . . 26

Using the Auto Station program Memory (ASPM). . . . 26

Notes for RDS operation. . . . . . . . . . . . . . . . . . . . . . . . . 26

09 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . 27

010 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Playable discs and formats . . . . . . . . . . . . . . . . . . . . . 30

Regarding copy protected CDs . . . . . . . . . . . . . . . . . . . 30

Supported audio file formats . . . . . . . . . . . . . . . . . . . . . 30

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Do not place objects on this unit . . . . . . . . . . . . . . . . . . 31

About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cleaning the lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cleaning discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

About specially shaped discs. . . . . . . . . . . . . . . . . . . . . 31

About iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . . . . . . . 32

Restoring all the settings to the defaults . . . . . . . . . . 32

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Before you start 01

5

En

English Français Español

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box

when you open it.

• Remote Control

•Power cord

• AM antenna cable

• FM wire antenna

• AAA batteries (R03) x 2

• Non-skid pads x 8

•iPad stand

• Warranty card

• Operating instructions (this document)

Loading the batteries in the

remote control

1 Open the rear lid and load the batteries as

illustrated below.

2 Close the rear lid.

CAUTION

• Do not use any batteries other than the ones specified.

Also, do not use a new battery together with an old one.

• When loading the batteries into the remote control, set

them in the proper direction, as indicated by the polarity

marks ( and ).

• Do not heat batteries, disassemble them, or throw them

into flames or water.

• Batteries may have different voltages, even if they are the

same size and shape. Do not use different types of

batteries together.

• To prevent leakage of battery fluid, remove the batteries

if you do not plan to use the remote control for a long

period of time (1 month or more). If the fluid should leak,

wipe it carefully off the inside of the case, then insert

new batteries. If a battery should leak and the fluid

should get on your skin, flush it off with large quantities

of water.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

• WARNING

Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the life or

performance of batteries.

Using the remote control

The remote has a range of about 7 m at an angle of about 30º

from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can interfere

with each other. Avoid using remotes for other

equipment located close to this unit.

• Replace the batteries when you notice a fall off in the

operating range of the remote.

STANDBY/ON





iPod CD

USB TUNE

R

AUDIO IN/LIN

E

DISPLAYFO

L

D

E

R

M

ENU

PRESET VOL

U

ME

ST/MONO ASPM

PT

YDISPLAY

+

M

U

T

E

TUN

E

–

TUNE+

D

IM

M

E

R













–

+

–

MEMORY

/PROGR

AM

123

4

5

6

789

0

TV O

UT

CLOCK/TI

MER

SLEEP

EQULIZER

P.B

A

SS

BAS

S/

T

RE

B

LE

R

A

NDOM

C

LE

AR RE

PEAT

OPEN/

CL

O

SE

RDS

ENTER

30°

7 m

30°

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Part names and functions02

6

En

Chapter 2:

Part names and functions

Remote control

1 1 STANDBY/ON

Switches the receiver between standby and on (page 18).

2 Input function buttons

Use to select the input source to this receiver (page 18).

3 CD Receiver control buttons

TV OUT

Setting iPod/iPhone video on/off.

CLOCK/TIMER

Use for setting the clock, as well as for setting and

checking the timers (page 12).

SLEEP

See Using the sleep timer on page 14.

4 Numeric buttons (0 to 9)

Use to enter the number (page 19).

5

CLEAR

Use to clear the programmed play (page 20).

6 CD Receiver control buttons

DISPLAY

Press to change the display for songs playing back from

CD or USB (page 21).

FOLDER

Use to select the folder of the MP3/WMA disc or USB

mass storage device (page 20).

MENU

Use to access the menu.

MEMORY/PROGRAM

Use to memory or program the MP3/WMA disc

(page 20).

7

F

/

G

/

H

/

I

(TUNE +/–), ENTER

Use to select/switch system settings and modes, and to

confirm actions.

Use TUNE +/– can be used to find radio frequencies

(page 24).

8 PRESET control buttons

Use to select preset radio stations (page 24).

9

MUTE

Mutes/unmutes the sound (page 12).

10 Playback control buttons

Use to control each function after you have selected it using

the input function buttons (page 18).

4

5

1

3

2

6

7

8

12

17

13

14

9

10

11

16

15

STANDBY/ON





iPod CD USB TUNER

AUDIO IN/LINE

DISPLAY FOLDER

MENU

PRESET VOLUME

ST/MONO ASPM PTY DISPLAY

+

MUTE

TUNE–

TUNE+

DIMMER

 







–

+

–

MEMORY

/PROGRAM

123

456

789

0

TV OUT

CLOCK/TIMER

SLEEP

EQUALIZER

P. BAS S

BASS/TREBLE

RANDOM

CLEAR REPEAT

OPEN/CLOSE

RDS

ENTER

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Part names and functions 02

7

En

English Français Español

11

Tuner

control buttons

ST/MONO

Use to switch the sound mode between stereo and

monaural. (page 24)

RDS ASPM

Use to search for RDS Auto station program memory

(page 25).

RDS PTY

Use to search for RDS program types (page 25).

RDS DISPLAY

Press to change the RDS display for information mode

(page 25).

12 OPEN/CLOSE

Use to open or close the disc tray (page 18).

13 Sound control buttons

Adjust the sound quality (page 13).

14 RANDOM

Press to randomize order play setting from a CD, iPod or USB

(page 19).

15

REPEAT

Press to change the repeat play setting from a CD, iPod or

USB (page 19).

16 Volume control buttons

Use to set the listening volume (page 12).

17

DIMMER

Dims or brightens the display. The brightness can be

controlled in four steps (page 12).

Speaker system

Important

Speaker grille cannot be removed.

Attaching the Non-skid pads

Apply the accessory non-skid pads to the bottom surfaces of

the speakers.

Important

Use the speaker is usually in an upright position.

3

2

1

1 Tweeter

2Woofer

3 Bass Reflex Duct

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Part names and functions02

8

En

Front panel

1Main display

2 Volume control

Use to set the listening volume (page 12).

3 Volume illumination

Light when the power on.

4 Headphone socket

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers.

5 AUDIO IN socket

Use to connect an auxiliary component using a stereo

minijack cable (page 27).

6 Remote sensor

Receives the signals from the remote control.

7 Disc tray

Place the disc, label side up (page 18).

8

TIMER

indicator

Lights when the receiver is power off with timer setting.

9 USB terminal

Use to connect your USB mass storage device or Apple iPod/

iPhone/iPad as an audio source (page 22).

TIMER VOLUME

PHONES AUDIO IN iPad

4 5 6 7 8 9

2 31

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Part names and functions 02

9

En

English Français Español

Top panel

1 iPod/iPhone connector port

To connect the iPod/iPhone, press the PUSH OPEN tab

(page 15).

2

1 STANDBY/ON

Switches the receiver between standby and on (page 18).

3 Playback control buttons

Selects the desired track or file to be played back. Use to stop

the playback. Stops playback or resumes playback from the

pause point.

4 INPUT

Selects the input source.

5 Disc tray open/close button

Use to open or close the disc tray (page 18).

STANDBY/ON







 

INPUT



PUSH OPEN

2 5

1

3 4

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Connections03

10

En

Chapter 3:

Connections

CAUTION

• Be sure to turn off the power and unplug the power cord

from the power outlet whenever making or changing

connections.

• Connect the power cord after all the connections

between devices have been completed.

Speaker connection

To connect the speaker cord to the connector, insert into the

speaker connector of the rear of the receiver.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Do not connect any speakers other than those supplied

to this system.

• Do not connect the supplied speakers to any amplifier

other than the one supplied with this system.

Connection to any other amplifier may result in

malfunction or fire.

• Do not attach these speakers to the wall or ceiling. They

may fall off and cause injury.

• These speakers are magnetically shielded. However,

depending on the installation location, color distortion

may occur if the speaker system is installed extremely

close to the screen of a television set. If this happens,

turn off the television set, and then turn it on after 15 to

30 minutes. If the problem persists, move the speaker

system away from the television set.

Connecting a TV

• When an iPod/iPhone is connected to this unit, the TV

output setting of iPod/iPhone is automatically set to

‘ON’.

Note

• Some iPod allow the TV output setting to be changed

while connected.

• When the iPod/iPhone is disconnected from this unit,

the iPod/iPhone’s TV output setting returns to its original

state.

AM

LOOP

ANTENNA VIDEO LINE

AC IN

OUT IN

SPEAKERS

L

R

RL

FM

UNBAL 75 Ω

Left

speaker

Right

speaker

This unit’s rear panel

VIDEO LINE

AC IN

OUT IN

SPEAKERS

L

R

RL

Yellow

TV

Video cable

(commercially available)

To video input

terminal

This unit’s rear panel

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Connections 03

11

En

English Français Español

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as

shown below. To improve reception and sound quality,

connect external antennas (see Using external antennas

below).

1 Connect the AM antenna wires.

Holding the connector to connect.

2 Fix the AM loop antenna to the attached

stand.

To fix the stand to the antenna, bend in the direction indicated

by the arrow (fig. a) then clip the loop onto the stand (fig. b).

3 Place the AM antenna on a flat surface and

in a direction giving the best reception.

4 Connect the FM wire antenna into the FM

antenna socket.

For best results, extend the FM antenna fully and fix to a wall

or door frame. Don’t drape loosely or leave coiled up.

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an external

FM antenna.

Plugging in

Before making or changing the connections, switch off the

power and disconnect the power cord from the AC outlet.

After you’ve finished making all connections, plug the unit

into an AC outlet.

CAUTION

• Do not use any power cord other than the one supplied

with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

AM

LOOP

ANTENNA

FM

UNBAL 75 Ω

2

1

3

4

fig. a

fig. b

ANTENNA

FM

UNBAL 75 Ω

One-touch PAL

connector

75 :coaxial

cable

VIDEO LINE

AC IN

OUT IN

SPEAKERS

L

R

RL

To AC outlet

This unit’s rear panel

Power cord

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Getting started04

12

En

Chapter 4:

Getting started

To turn the power on

Press the 1 STANDBY/ON to turn the power on.

After use:

Press the 1 STANDBY/ON to enter the power stand-by mode.

Note

• In standby mode, if iPod/iPhone/iPad is connected, the

unit turns charge mode.

Setting the clock

1 Press

1 STANDBY/ON

to turn the power on.

2 Press

CLOCK/TIMER

on the remote control.

“CLOCK” is shown on the main display.

3 Press

ENTER

.

4 Press

HI

to set the day, then press ENTER.

5 Press

HI

to set the hour, then press

ENTER.

6 Press

HI

to set the minute, then press

ENTER to confirm.

7 Press

ENTER

.

To confirm the time display:

Press the CLOCK/TIMER. The time display will appear for

about 10 seconds.

To readjust the clock:

Perform “Setting the clock” from step 1.

Note

• When power supply is restored after unit is plugged in

again or after a power failure, reset the clock.

General control

Input function

When the INPUT on main unit is pressed, the current function

will change to different mode. Press the INPUT repeatedly to

select desired function.

Display brightness control

Press DIMMER to dims the display brightness. The

brightness can be controlled in four steps.

Volume auto set-in

If you turn off and on the main unit with the volume set to 17

or higher, the volume starts at 16 and sets in to the last set

level.

Volume control

Turn the volume knob towards VOLUME (on main unit) or

press VOLUME +/- (on remote control) to increase or

decrease the volume.

CAUTION

• The sound level at a given volume setting depends on

speaker efficiency, location, and various other factors. It

is advisable to avoid exposure to high volume levels. Do

not turn the volume on to full at switch on. Listen to

music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

Muting

The volume is muted temporarily when pressing the MUTE on

the remote control. Press again to restore the volume.

STANDBY/ON





iPod CD USB TUNER

AUDIO IN/LINE

123

TV OUT

CLOCK/TIMER

SLEEP

EQUALIZER

OPEN/CLOSE

DISPLAY FOLDER

MENU

PRESET VOLUME

TUNE–

TUNE+

MEMORY

/PROGRAM

ENTER

CD AM

USB/IPOD

FM

AUDIO IN

IPOD

LINE

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Getting started 04

13

En

English Français Español

Sound controls

Equalizer

When the EQUALIZER is pressed, the current mode setting

will be displayed. To change to a different mode, press the

EQUALIZER repeatedly until the desired sound mode

appears.

P.bass control

When the power is first turned on, the unit will enter the

P.bass mode which emphasises the bass frequencies. To

cancel the P.bass mode, press the P.BASS on the remote

control.

Bass/treble control

Press the BASS/TREBLE, then press HI to adjust the bass

or treble.

Note

EQUALIZER, P.BASS and BASS/TREBLE, the simultaneous

operation is not possible. Among the features of these three,

one feature will only work you have selected.

If you select one of three functions, features

that are not selected will be set as follows.

1 If you change the settings of

P.BASS

(

ON

/

OFF

).

• EQUALIZER : FLAT

• BASS/TREBLE : BASS=0, TREBLE=0

2 If you change the settings of EQUALIZER.

• P.BASS : OFF

• BASS/TREBLE : BASS=0, TREBLE=0

3 If you change the settings of BASS/TREBLE.

• P.BASS : OFF

• EQUALIZER : FLAT

Setting the wake-up timer

Used to change the existing timer setting, or to set a new

timer.

1 Press

1 STANDBY/ON

to turn the power on.

2 Press and hold

CLOCK/TIMER

.

3 Press

HI

to select “ONCE” or “DAILY”,

then press ENTER.

ONCE – Once timer play works for one time only at a

preset time.

DAILY – Daily timer play works at the same preset time

and days of week.

4 Press

HI

to select “TIMER SET”, then

press ENTER.

5 Press

HI

to select the timer playback

source, then press

ENTER

.

• CD, FM, AM, USB/IPOD, IPOD, AUDIO IN and LINE can

be selected as the playback source.

6 Press

HI

to select the timer day, then

press ENTER.

7 Press

HI

to set the hour, then press

ENTER.

8 Press

HI

to set the minute, then press

ENTER.

• Set the time to finish as in steps 7 and 8 above.

9 Adjust the volume press VOLUME +/- , then

press ENTER.

10 Press

1 STANDBY/ON

to enter the power

standby mode.

•The TIMER indicator lights up.

POP

FLAT Equalizer o.

JAZZ

ROCK

For pop music.

For jazz.

For rock.

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Getting started04

14

En

Calling the wake-up timer

It can be used to re-use an existing timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press

HI

to select “TIMER ON”, then press

ENTER.

Cancelling the wake-up timer

It can be used to turn off the timer setting.

1 As well as steps 1 through 3 in “Setting the

wake-up timer”.

2 Press

HI

to select “TIMER OFF”, then

press ENTER.

Using the wake-up timer

1 Press

1 STANDBY/ON

to turn the power

off.

2 At the wake-up time, this unit will turn on

automatically and play the selected input

function.

Note

• If at the wake-up time iPod/iPhone/iPad is not connected

to this unit or a disc is not inserted, this unit will be

turned to on and not play back the track.

• Some discs may not be played automatically at the wake-

up time.

• If you set the timer, take one minute or more between the

start and end time.

Using the sleep timer

The sleep timer switches off the unit after a specified time so

you can fall asleep without worrying about it.

1 Press

SLEEP

repeatedly to select a switch off

time.

Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120

min, 150 min, 180 min or OFF. The newly set value displays for

3 seconds, and then the setting is completed.

Note

• The sleep timer can be set by pressing SLEEP while the

remaining time is displayed.

Using Headphones

Connect to the jack plug of the headphones.

When the headphones are connected, there is no sound

output from the speakers.

• Do not turn the volume on to full at switch on and listen

to music at moderate levels. Excessive sound pressure

from earphones and headphones can cause hearing

loss.

• Before plugging in or unplugging the headphone,

reduce the volume.

• Be sure your headphone has a 3.5 mm diameter plug

and impedance between 16

: and 50 :. The

recommended impedance is 32

:.

• Audio from the iPod/iPhone/iPad cannot be heard via

the headphones connected to the unit. “HP MUTE” will

be displayed if you connect the headphones when the

iPod/iPhone/iPad function is selected.

TIMER VOLUME

PHONES AUDIO IN iPad

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

iPod/iPhone/iPad playback 05

15

En

English Français Español

Chapter 5:

iPod/iPhone/iPad playback

Merely by connecting your iPod/iPhone/iPad to this unit, you

can enjoy high-quality sound from your iPod/iPhone/iPad.

This unit can also be connected to a television set, letting you

view videos from your iPod/iPhone. Playback setting for iPod/

iPhone/iPad music can be performed from this unit or the

iPod/iPhone/iPad itself.

• To connect a TV, see page 10.

Confirming what iPod/iPhone/iPad

models are supported

The iPod/iPhone/iPad playable on this unit are shown below.

• Video output for iPod/iPhone is only compatible when

connected to the Dock connector.

Note

• Pioneer does not guarantee that this unit plays iPod/

iPhone/iPad models other than the ones specified.

• Some functions may be restricted depending on the

model or software version.

• iPod/iPhone/iPad is licensed for reproduction of non-

copyrighted materials or materials the user is legally

permitted to reproduce.

• Features such as the equalizer cannot be controlled

using this system, and we recommend switching the

equalizer off before connecting.

• Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising from

any inconvenience or loss of recorded material resulting

from iPod/iPhone/iPad failure.

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• This system has been developed and tested for the

software version of iPod/iPhone/iPad indicated on the

website of Pioneer (http://pioneer.jp/homeav/support/

ios/eu/).

• Installing software versions other than indicated on the

website of Pioneer to your iPod/iPhone/iPad may result

in incompatibility with this system.

• This unit cannot be used to record CD, tuner or other

content on an iPod/iPhone/iPad.

Connecting your iPod/iPhone/iPad

CAUTION

• Do not use an adaptor that converts into a Lightning

connector on the unit's iPod/iPhone connector to

connect an iPod/iPhone/iPad. This may lead to

malfunction/damage to the connector.

Please connect these Lightning connector devices to the

USB port on the front of the unit.

iPhone 5, iPad (4th generation), iPad mini, iPod touch

(5th generation), iPod nano (7th generation)

• When connecting iPod/iPhone devices, always use the

dock adapter provided with iPod/iPhone devices, or a

commercially available adapter designed to support

iPod/iPhone. The iPod/iPhone cannot be connected

without a dock adapter; attempting to connect an iPod/

iPhone without it will cause damage or malfunction.

• An iPod/iPhone universal dock adapter is not supplied

with this unit.

Important

• If you are mounting the protective cover of a

commercially available iPod/iPhone/iPad, you may not

be able to connect iPod/iPhone/iPad to this unit.

iPod/iPhone/iPad

Dock connector

(Audio/Video)

USB Terminal

(Audio only)

iPod nano 3G/4G/5G/6G

*

* iPod nano 6G is supports audio only.



iPod nano 7G — 

iPod touch 1G/2G/3G/4G 

iPod touch 5G — 

iPhone 

iPhone 3G 

iPhone 3GS 

iPhone 4 

iPhone 4S 

iPhone 5 — 

iPad mini — 

iPad — 

iPad 2 — 

iPad 3G/4G — 

BL3RGB;&0IP࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸯㸷᪥ࠉ㔠᭙᪥ࠉ༗๓㸯㸯᫬㸳㸷ศ

iPod/iPhone/iPad playback05

16

En

Connecting iPod/iPhone to the top

panel

1 Press the PUSH OPEN.

2 Open the iPod/iPhone connector port.

3 Connect your iPod/iPhone.

• When iPod/iPhone is not connected to the unit, close

the iPod/iPhone connector port firmly.

Connecting iPod/iPhone/iPad using

supplied stand

1 Connect the iPod/iPhone/iPad cable to the

unit.

2 Pass the iPod/iPhone/iPad cable through the

bottom of the stand and connect it to the iPod/

iPhone/iPad.

3 Set up to stand the iPod/iPhone/iPad.

PUSH OPEN

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

iPod/iPhone/iPad playback 05

17

En

English Français Español

Watching iPod/iPhone videos on your

TV

To watch iPod/iPhone videos on a television, connect it using

a video cable. When an iPod/iPhone is connected to this unit,

the TV output setting of the iPod/iPhone is automatically set

to ‘ON’.

CAUTION

• Before making or changing the connections, switch off

the power and disconnect the power cord from the

power outlet. Plugging in should be the final step.

Note

• For detailed instructions on using the iPod/iPhone,

please refer to the manual supplied with the iPod/

iPhone.

• Some iPods allow the TV output setting to be changed

while connected.

• When the iPod/iPhone is disconnected from this unit,

the iPod/iPhone’s TV output setting returns to its original

state.

Playing iPod/iPhone

1 Connect your iPod/iPhone.

• If an iPod/iPhone is connected when this unit is on,

playback of the iPod/iPhone will not begin.

2 Press

iPod

or

USB

as the input source.

“IPOD” or “USB/IPOD” is shown on the main display.

3 When the recognition is completed, will

begin playing automatically.

• The available iPod/iPhone playback control by this unit is

!, + ), *,.

• In the following case, operate your iPod/iPhone directly:

- Searching a file by artist name or genre.

- Playing in the repeat or random mode.

- Watching videos stored in iPod/iPhone on your television.

Playing iPad

1 Connect your iPad.

• If an iPad is connected when this unit is on, playback of

the iPad will not begin.

2 Press

USB

as the input source.

“USB/IPOD” is shown on the main display.

3 When the recognition is completed, will

begin playing automatically.

• The available iPad playback control by this unit is !,

+ ), *,.

• In the following case, operate your iPad directly:

- Searching a file by artist name or genre.

- Playing in the repeat or random mode.

CAUTION

• When your iPod/iPhone/iPad is connected to this unit

and you wish to operate the iPod/iPhone/iPad directly,

be sure to steady the iPod/iPhone/iPad with the other

hand to prevent malfunctions due to faulty contacts.

Note

• For detailed instructions on using the iPod/iPhone/iPad,

please refer to the manual supplied with the iPod/

iPhone/iPad.

• iPod/iPhone/iPad recharging occurs whenever an iPod/

iPhone/iPad is connected to this unit. (This function is

supported in standby mode as well.)

• When input is switched from iPod to another function,

iPod/iPhone/iPad playback is temporarily stopped.

Important

If this unit cannot play your iPod/iPhone/iPad, perform the

following troubleshooting checks:

• Check whether the iPod/iPhone/iPad is supported by

this unit.

• Reconnect the iPod/iPhone/iPad to the unit. If this

doesn’t seem to work, try resetting your iPod/iPhone/

iPad.

• Check the iPod/iPhone/iPad software is supported by

this unit.

If the iPod/iPhone/iPad cannot be operated, check the

following items:

• Is the iPod/iPhone/iPad connected correctly? Reconnect

the iPod/iPhone/iPad to the unit.

• Is the iPod/iPhone/iPad experiencing a hangup? Try

resetting the iPod/iPhone/iPad, and reconnect it to the

unit.

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Disc playback06

18

En

Chapter 6:

Disc playback

This system can play back a standard CD, CD-R/RW in the CD

format and CD-R/RW with MP3 or WMA files, but cannot

record on them. Some audio CD-R and CD-RW discs may not

be playable due to the state of the disc or the device that was

used for recording.

MP3:

MP3 is a form of compression. It is an acronym which stands

for MPEG Audio Layer 3. MP3 is a type of audio code which is

processed by significant compression from the original audio

source with very little loss in sound quality.

• This system supports MPEG-1/2 Audio Layer 3 (Sampling

rates: 8 kHz to 48 kHz; Bit rates: 64 kbps to 384 kbps).

• During VBR file playback, time counter in the display

may differ from its actual playback time.

WMA:

WMA (Windows Media Audio) files are Advanced System

Format files that include audio files which are compressed

with Windows Media Audio codec. WMA is developed by

Microsoft as an audio format file for Windows Media Player.

• This system supports WMA (Sampling rates: 32 kHz/44.1

kHz/48 kHz; Bit rates: 64 kbps to 320 kbps).

• During VBR file playback, time counter in the display

may differ from its actual playback time.

Playing discs or files

1 Press

1 STANDBY/ON

to turn the power on.

2 Press

CD

on the remote control or

INPUT

repeatedly on the main unit to select CD input.

3 Press

$ OPEN/CLOSE

to open the disc tray.

4 Place the disc on the disc tray, label side up.

5 Press

$ OPEN/CLOSE

to close the disc tray.

6 Press

!

to start playback.

After the last track is played, the unit will stop automatically.

CAUTION

• Do not place two discs in one disc tray.

• Do not play discs of special shapes (heart, octagon, etc).

It may cause malfunctions.

• Do not push the disc tray whilst it is moving.

• If the power fails whilst the tray is open, wait until the

power is restored.

• Be sure to place 8 cm disc in the middle of the disc tray.

Note

• Due to the structure of the disc information, it takes longer

to read an MP3/WMA disc than a normal CD

(approximately 20 to 90 seconds).

• When the beginning of the first track is reached during fast

reverse, the unit will enter the playback mode (only for CD).

• Rewritable multi-session discs with unfinished writing, can

still be played.

• If TV or radio interference occurs during CD operation,

move the unit away from the TV or radio.

Tip

• When no operation has done in CD mode and the audio

file is not played for more than 15 minutes, the power will

automatically turn off.

Various disc functions

Function Main

unit

Remote

control

Operation

Play

Press in the stop mode.

Stop

Press in the playback mode.

Pause

Press in the playback mode.

Press

!

to resume playback

from the paused point.

Track up/

down

Press in the playback or stop

mode.

If you press the button in the

stop mode, press

!

to start

the desired track.

Fast

forward/

reverse

Press and hold down in the

playback mode.

Release the button to resume

playback.







 









 









;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Disc playback 06

19

En

English Français Español

Advanced CD or MP3/WMA disc

playback

Direct track search

By using the numeric buttons, the desired tracks on the

current disc can be played.

Use the numeric buttons on the remote control to

select the desired track whilst playing the selected

disc.

Note

• A track number higher than the number of tracks on the

disc cannot be selected.

To stop playback:

Press #.

Repeat play

Repeat play can play one track, all tracks or a programmed

sequence continuously.

To repeat one track:

Press REPEAT repeatedly until “RPT ONE” appears. Press

ENTER.

To repeat all tracks:

Press REPEAT repeatedly until “RPT ALL” appears. Press

ENTER.

To repeat desired tracks:

Perform steps 1 - 5 in “Programmed play” section on next

page and then press REPEAT repeatedly until “RPT ALL”

appears. Press ENTER.

To cancel repeat play:

Press REPEAT repeatedly until “RPT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press #.

Otherwise, the disc will play continuously.

• During repeat play, random play is not possible.

Random play

The tracks on the disc can be played in random order

automatically.

To random play all tracks:

Press RANDOM repeatedly until “RDM ON” appears. Press

ENTER.

To cancel random play:

Press RANDOM repeatedly until “RDM OFF” appears. Press

ENTER.

Note

• If you press the , during random play, you can move

to the track selected next by the random operation. On

the other hand, the + does not allow you to move to

the previous track. The beginning of the track being

played will be located.

• In random play, the unit will select and play tracks

automatically. (You cannot select the order of the

tracks.)

• During random play, repeat play is not possible.

STANDBY/ON





iPod CD USB TUNER

AUDIO IN/LINE

DISPLAY FOLDER

TUNE+

123

4 5 6

7 89

0

TV OUT

CLOCK/TIMER

SLEEP

EQUALIZER

P.BASS

BASS/TREBLE

RANDOM

CLEAR REPEAT

OPEN/CLOSE

DISPLAY FOLDER

MENU

PRESET VOLUME

ST/MONO ASPM PTY DISPLAY

+

MUTE

TUNE–

TUNE+

DIMMER

 







–

+

–

MEMORY

/PROGRAM

0

RDS

ENTER

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

Disc playback06

20

En

Programmed play (CD or MP3/WMA)

You can choose up to 32 selections for playback in the order

you like.

1 Whilst in the stop mode, press

MEMORY

/

PROGRAM

on the remote control to enter the

programming save mode.

2 Press

+,

or the numeric buttons on the

remote control to select the desired tracks.

3 Press ENTER to save folder and track

number.

4 Repeat steps 2 - 3 for other folder/tracks. Up

to 32 tracks can be programmed.

• If you want to check the programmed tracks, press

MEMORY/PROGRAM.

• If you make a mistake, the last programmed tracks will

be canceled by pressing CLEAR.

5 Press

!

to start playback.

To cancel the programmed play mode:

To cancel the programmed play, press twice # on the remote

control. The display will show “PRG CLR” and all the

programmed contents will be cleared.

Adding tracks to the program:

Press the MEMORY/PROGRAM. Then follow steps 2 - 3 to

add tracks.

Note

• When a disc is ejected, the program is automatically

cancelled.

• If you press the 1 STANDBY/ON to enter the standby

mode or change the function from CD to another, the

programmed selections will be cleared.

• During the program operation, random play is not

possible.

About downloading MP3/WMA

There are many music sites on the internet that you can

download MP3/WMA music files. Follow the instructions

from the website on how to download the music files. You can

then play back these downloaded music files by burning them

to a CD-R/RW disc.

• Your downloaded song/files are for personal use only.

Any other usage of the song without owner’s permission,

is against the law.

About folder playback order

If MP3/WMA files are recorded in several folders, a folder

number will be set to each folder automatically.

These folders can be selected by the FOLDER on the remote

control. If there is no supported file formats inside the

selected folder, the folder is skipped and the next folder will be

selected.

Example: How to set folder number if MP3/WMA format files

are recorded as below figure.

1 ROOT folder is set as folder 1.

2 As for folders inside ROOT folder (Folder A

and Folder B), the folder which is recorded

earlier on the disc will be set as folder 2 and

folder 3.

3 As for folder inside Folder A (Folder C and

Folder D), the folder which is recorded earlier on

the disc will be set as folder 4 and folder 5.

4 Folder E that is inside Folder D will be set as

folder 6.

• The folder and file order information which is recorded

on the disc depends on the writing software. There

maybe possibilities that this unit will playback the files

not according to our expected playback order.

• From a disc with MP3/WMA files up to 255 folders and

999 files (including non playable files) can be read.

ROOT

(FOLDER 1)

FOLDER A

(FOLDER 2)

FOLDER B

(FOLDER 3)

FILE 9

FILE 10

FILE 3

FILE 4

FILE 5

FILE 6

FILE 7

FILE 8

FOLDER E

(FOLDER 6)

FOLDER C

(FOLDER 4)

FOLDER D

(FOLDER 5)

FILE 1

FILE 2

;&0B6<;(B(QERRN࣮࣌ࢪ㸰㸮㸯㸱ᖺ㸲᭶㸶᪥ࠉ᭶᭙᪥ࠉ༗๓㸯㸯᫬㸲㸷ศ

La pagina si sta caricando...

Pioneer X-CM31-J Manuale del proprietario

Pioneer X-CM31-J Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti