®
FUSION
®
MS-UD/AV650/755
Installation Instructions
Important Safety Information
WARNING
Failure to follow these warnings and cautions could result in
personal injury, damage to the vessel, or poor product
performance.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
This device must be installed according to these instructions.
Disconnect the vessel's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded, following the instructions in the guide.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact FUSION Product Support.
What's In the Box
• Two Mounting plates
• Mounting hardware
◦ Four 8-gauge, self-tapping screws
◦ Four M4 machine screws
• Power and speaker wiring harnesses
• RCA splitter
• Micro-USB to USB cable (UD models only)
• Lightning
™
connector to USB cable (UD models only)
• Apple
®
30-pin to USB cable (UD models only)
• Remote control (AV models only)
• Two AAA batteries (AV models only)
Tools Needed
• Phillips screwdriver
• Electric drill
• Drill bit (size varies based on surface material and screws
used)
• Rotary cutting tool or jigsaw
• Silicone-based marine sealant (optional)
Mounting Considerations
• The stereo must be mounted in a location where there is
enough clearance for the open door of the stereo as
indicated on the template.
• The stereo must be mounted in a location that allows open
airflow around the rear of the stereo for heat ventilation.
• The stereo must be mounted within 45° of the horizontal
plane.
•
The cable should have a drip loop to allow water to drip down
off the cable and avoid damaging the stereo.
• If you want to mount the stereo outside the boat, it must be
mounted in a location well above the waterline, where it is not
submerged.
• If you want to mount the stereo outside the boat, it should be
mounted in a location where it will not be damaged by a
docks, pilings, or other pieces of equipment.
• To avoid interference with a magnetic compass, the stereo
should be installed at least 15 cm (5.9 in.) away from a
compass.
Mounting the Stereo
NOTICE
Be careful when cutting the hole to flush mount the stereo.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the stereo after it is mounted.
Before mounting the stereo, you must choose a location
following the guidelines above.
1
Trim the template and make sure it fits in the selected
location.
2
Secure the template to the selected location.
3
Using a drill bit appropriate for the mounting surface, drill the
hole inside the corner of the dashed line on the template to
prepare the mounting surface for cutting.
4
Using a jigsaw or rotary tool, cut the mounting surface along
the inside of the dashed line indicated on the template.
5
If necessary, remove the sun cover from the stereo.
6
Place the stereo in the cutout to test the fit.
7
If necessary, use a file and sandpaper to refine the size of
the cutout.
8
After the stereo fits correctly in the cutout, ensure the
mounting holes on the stereo line up with the pilot holes on
the template.
9
If the mounting holes on the stereo do not line up, mark the
new pilot-hole locations.
10
Using an appropriately sized drill bit for the mounting surface
and screw type, drill the pilot holes.
11
Remove the template from the mounting surface.
12
Connect the wiring harnesses and wires, while observing
polarity.
13
Place the mounting gasket on the back of the stereo
À
.
August 2018
190-02249-02_0B
14
If necessary, place the nut plates
Á
behind the dashboard.
15
Place the stereo in the cutout.
16
Secure the stereo to the mounting surface using the included
screws
Â
.
17
If necessary, secure the back of the stereo with a back strap
or brace (not included).
Connection Considerations
The stereo must be connected to power, to speakers, and to
media input sources to function correctly. You should carefully
plan the layout of the stereo, wired remote, speakers, optional
NMEA 2000
®
network, and your input sources before making
any connections.
Power and Speaker Wiring Harness Wire
Identification
Wire Function Wire
Color
Notes
Power (+) Yellow This should be connected to a constant
12 Vdc source capable of supplying
15 A. All 12 V wiring must be fused at
the power source end of your cable
using a 15 A fuse.
Ground (-) Black This should be connected battery
negative before connecting the yellow
wire. All accessories connected to the
stereo must share a common ground
location.
Ignition Red This should be connected to a
separately switched 12 Vdc connection,
such as an ignition bus, to turn the
stereo on and off. If you are not using a
switched 12 Vdc connection, you must
connect this to the same source as the
yellow (power) wire.
Amplifier on Blue This is connected only when using an
optional external amplifier.
Telephone Mute Brown When connected to ground and a call is
received on a hands-free mobile phone,
this mutes the audio or switches the
input to AUX IN 2 or ARC source (ARC
source is available on the MS-AV755
only). This is configurable in the Settings
menu.
Dim Orange This can be connected to the boat's
illumination wire to dim the stereo
screen when the lights are on.
This must be connected to a wire gauge
suitable for the fuse supplying the circuit
it is connected to.
Speaker zone 1
left (+)
White
Speaker zone 1
left (-)
White/
black
Speaker zone 1
right (+)
Gray
Speaker zone 1
right (-)
Gray/black
Wire Function Wire
Color
Notes
Speaker zone 2
left (+)
Green
Speaker zone 2
left (-)
Green/
black
Speaker zone 2
right (+)
Purple
Speaker zone 2
right (-)
Purple/
black
Wiring Harnesses
À
Antenna Motorola-style standard antenna connector
Á
SIRIUSXM TUNER SiriusXM
®
connector
Â
WIRED REMOTE
NMEA 2000
Connect to a NMEA 2000 network or a
FUSION wired remote
Ã
USB USB-A industry standard
Ä
Video 755 models: HDMI
®
cable and Ethernet
650 models: composite and component
Å
AUX IN 1, AUX IN 2 Red and white RCA stereo line inputs for
sources such as CD and MP3 players
Æ
Zone connectors Line outputs for speakers and subwoofer
amplifiers. 650 models have three zones. 755
models have four zones.
Ç
Power and speaker
wiring harness
See Power and Speaker Wiring Harness Wire
Identification, page 2
Connecting to Power
When connecting the stereo to power, you must connect both
power wires. You should connect the yellow power wire directly
to the battery. This provides power to the stereo and a constant
trickle-power standby feed.
You should connect the red ignition wire to the same battery
through the ignition or another manual switch to turn the stereo
on and off. If you are not routing the red wire through the ignition
or another manual switch, you can connect the red wire to the
yellow wire, and connect them both to the positive (+) battery
terminal.
You must connect the power wires to the battery through a 15 A
fuse or a 15 A circuit breaker.
If it is necessary to extend the yellow power and black ground
wires, use 14 AWG (2.08 mm
2
) wire. For extensions longer than
1 m (3 ft.), use 12 AWG (3.31 mm²) wire. If it is necessary to
extend the red wire, use 22 AWG (0.33 mm
2
) wire.
2 FUSION MS-UD/AV650/755 Installation Instructions
1
Route the yellow power
À
, red ignition
Á
, and black ground
Â
wires to the battery, and route the wiring-harness plug to
the stereo.
Do not connect the wiring harness to the stereo until all of the
bare wire connections have been made.
2
Connect the black wire to the negative (-) battery terminal.
3
If you are routing the red wire through the ignition or another
manual switch
Ã
, connect the red ignition wire to the ignition
or switch.
4
Connect the red wire to the yellow wire, install a 15 A fuse
Ä
as close to the battery as possible, and connect both wires to
the positive (+) battery terminal.
NOTE: If you are running the red wire through a fused switch,
it is not necessary to connect the red wire to the yellow wire
or to add an another fuse to the red wire.
Enabling Standby Mode
You can set the stereo to enter a low-power standby mode when
you press . When you press again, it takes less than the
typical 30 seconds to turn on.
NOTE: When the stereo is in low-power standby mode, it
continues to draw current from the battery. The maximum
current draw in standby mode is 200 mA.
Select > Settings > Standby Mode.
The stereo now enters standby mode when you press .
Speaker Zones
You can group speakers in one area into speaker zones. This
enables you to control the audio level of the zones individually.
For example, you could make the audio quieter in the cabin and
louder on deck.
Zones 1 and 2 are powered by the on-board amplifier. To use
the RCA line outputs and the RCA subwoofer outputs, you must
connect external amplifiers.
You can set the balance, volume limit, subwoofer level, and
name for each zone.
Subwoofer Connection Considerations
This stereo supports output to a powered subwoofer for each
zone.
The subwoofer outputs are mono line-level signals tied to the
corresponding zone volume.
A splitter is provided to connect this mono output to the stereo
input of a subwoofer amplifier. Additional splitters (not included)
are needed for additional subwoofer connections.
Speaker Amplifier Connection Considerations
This stereo supports output to an external amplifier for each
zone.
The zone outputs are stereo line-level signals tied to the zone
volume. A standard RCA cable (not included) is required to
connect each zone output to an external amplifier.
The blue wire from the wiring harness must be connected to
each amplifier to provide a signal to turn on the amplifier with the
stereo. If it is necessary to split or extend this blue signal wire,
use 22 AWG (0.33 mm
2
) wire.
Common Connections to the Stereo
You can connect a variety of additional media inputs and
outputs to the stereo, depending on the stereo model and the
devices to which you are connecting.
The connectors are color coded to assist you in making the
correct connections. For example, if your TV has RCA line out
ports, you can connect an RCA cable to the AUX IN 1 or AUX IN
2 connector on the stereo. This table lists some possible ways to
connect devices to the stereo.
NOTE: Not all connectors are available on all stereo models.
Input Stereo Connections
FM/AM radio antenna* Antenna connector
SiriusXM Connect Tuner SIRIUSXM TUNER connector
USB device USB connector or the built-in dock (UD
models)
TV with a composite video
connector and RCA audio
line outs
Yellow to COMPOSITE VIDEO (MS-AV650
only)
RCA line outs from TV to AUX IN 1 or AUX
IN 2
TV with component
connectors and RCA
audio line outs
Three component video connectors to
matching connectors on stereo (MS-AV650
only)
RCA line outs from TV to AUX IN 1 or AUX
IN 2
TV with an HDMI
connector
HDMI cable (MS-AV755 only)
* You should connect a marine, AM/FM, ground-independent
antenna.
Ethernet and Wireless Support
You can connect a compatible FUSION-Link
™
MFD to the
entertainment system using the Ethernet port. See the
documentation provided with your MFD for more information.
NOTE: Some MFDs with Ethernet support may not be
compatible with FUSION-Link over Ethernet, but may be
compatible with FUSION-Link over NMEA 2000 instead.
You can connect a wireless Ethernet router to the entertainment
system to control the device with Wi‑Fi
®
. You can download free
apps from the Apple App Store
SM
for Apple devices. Android
™
apps are available through Google Play
™
.
For more information, see www.fusionentertainment.com.
Audio Return Channel
The Audio Return Channel (ARC) enables you to play the audio
from a television with HDMI technology over the stereo system
speakers.
ARC eliminates the need to connect a separate audio cable
from the television to the stereo. Typically, in televisions without
ARC, to play the audio from the television over the stereo
system speakers, you would need a separate cable. With ARC,
the HDMI cable sends the television audio to the stereo.
HDMI version 1.4 with ethernet cables support ARC. When
planning your stereo installation, check whether your devices
support ARC. Most devices that support ARC have an ARC
label on the HDMI connector that supports ARC.
Single-Zone System Wiring Example
FUSION MS-UD/AV650/755 Installation Instructions 3
À
Speakers
Á
Water-tight connection
Three-Zone System Wiring Example
À
Zone 1 speakers, powered from Class D amplifier in stereo
Á
Zone 2 speakers, powered from Class D amplifier in stereo
Â
Zone 3 speakers, powered by an external amplifier connected to the
zone 3 line out
Ã
External amplifier (not included)
Ä
Water-tight connections
Å
Remote on
NMEA 2000 System Wiring Diagram
À
Stereo
Á
Supported chartplotter MFD
Â
FUSION NRX series wired remote
Ã
In-line switch
Ä
NMEA 2000 power cable
Å
NMEA 2000 cable from the stereo
This can be extended to a maximum length of 6 m (20 ft.) using a
NMEA 2000 cable.
Æ
NMEA 2000 drop cable from the MFD
Ç
NMEA 2000 drop cable from the wired remote
È
NMEA 2000 terminator or backbone cable
É
NMEA 2000 T-connector
Configuring an Optional Wired Remote
NOTICE
The stereo is configured by default to work with a NMEA 2000
network, and the NRX Power option should be enabled only
when an optional remote is connected directly to the stereo.
Enabling this option when the stereo is connected to a NMEA
2000 network may damage other devices on the NMEA 2000
network.
If you connect an optional wired NRX remote directly to the
stereo, and not through a NMEA 2000 network , additional
configuration is needed.
1
Select > Settings.
2
Select an option:
• If you connected both your stereo and your optional wired
remote to a NMEA 2000 network, make sure the NRX
Power option is not selected. This enables the optional
remote to receive power from the NMEA 2000 network.
• If you connected the optional wired remote directly to the
stereo through the NMEA 2000 connector, select the NRX
Power option. This enables the stereo to supply power to
the optional remote.
Stereo Information
Specifications
General
Weight 0.88 kg (1.96 lb.)
Water resistance IEC 60529 IPX5
Operating temperature range From 0 to 50°C (from 32 to 122°F)
Storage temperature range From -20 to 70°C (from -4 to 158°F)
Compass-safe distance 15 cm (5.9 in.)
Input voltage From 10.8 to 16 Vdc
NMEA 2000 LEN 1 (50 mA)
Bluetooth
®
Class 2
Bluetooth/ANT
®
frequency From 2,400 to 2,483.5 MHz
Bluetooth/ANT power (max.) 8 dBm EIRP
On-board, Class D Amplifier
Output music power per channel 70 W max. x 4 at 2 ohms
Total output music power 280 W max.
Output power per channel
(14.4 VDC at 10% THD+N)
43W RMS x 4 @ 2 ohms
26W RMS x 4 @ 4 ohms
Line output level (max.) 6 V (peak to peak)
Aux input level (typical) 1 V RMS
Current Consumption
Stereo is off Ignition off Standby Mode = Off < 3 mA
Standby Mode = On < 200 mA
Ignition on Standby Mode = Off < 20 mA
Standby Mode = On < 200 mA
Stereo is on Muted <900 mA
Typical listening volume 2 A
Maximum current draw 15 A
Tuner Europe and
Australasia
USA Japan
FM radio
frequency range
87.5 to 108 MHz 87.5 to
107.9 MHz
76 to 95 MHz
FM frequency
step
50 kHz 200 kHz 50 kHz
AM radio
frequency range
522 to 1620 kHz 530 to
1710 kHz
522 to
1620 kHz
AM frequency
step
9 kHz 10 kHz 9 kHz
4 FUSION MS-UD/AV650/755 Installation Instructions
Media Player Compatibility
If you have a UD model, you can use the included adapter
cables to connect popular media players to the internal docking
station or the connector on the back of the stereo. If you have an
AV model, you can use the USB cables that came with your
media player to connect the player to the connector on the back
of the stereo.
Only media players with ports on the bottom, not on the sides, fit
in the docking station. Media players larger than 144 × 71 ×
13 mm (5.67 × 2.80 × 0.52 in.) do not fit in the docking station.
Cable Connector in
Dock
Devices
Micro-USB connector Supported media players. See
www.fusionentertainment.com.
Apple 30-pin
connector
Apple iPhone
®
4s.
Apple Lightning
connector
Apple iPhone 7 Plus, iPhone 7, iPhone SE,
iPhone 6s Plus, iPhone 6s, iPhone 6 Plus,
iPhone 6, iPhone 5s, iPhone 5c, and iPhone 5.
iPod touch
®
(5th and 6th generation) and iPod
nano
®
(7th generation).
You also can connect a FAT32- or NTFS-formatted USB flash
drive directly to the USB port.
Stereo Dimension Drawings
Top Dimensions
179.94
À
35 mm (1.367 in.)
Á
25 mm (0.97 in.)
Â
180 mm (7.08 in.)
Front Dimensions
À
216 mm (8.50 in.)
Á
78 mm (3.08 in.)
Side Dimensions
À
52 mm (1.37 in.)
Á
177 mm (6.97 in.)
Â
28 mm (1.08 in.)
Software Updates
For best results, you should update the software in all FUSION
devices at the time of installation to ensure compatibility.
Go to www.fusionentertainment.com/marine to download the
latest software. Software updates and instructions are available
on your device product page.
Registering Your FUSION MS-UD/AV650/755
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
© 2017–2018 Garmin Ltd. or its subsidiaries
Garmin
®
, the Garmin logo, FUSION
®
, and the Fusion logo are trademarks of Garmin Ltd.
or its subsidiaries, registered in the USA and other countries.
FUSION-Link
™
is a
trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without
the express permission of Garmin.
Android
™
and Google Play
™
are trademarks of Google Inc. Apple
®
, the Apple logo, iPod
®
,
iPod touch
®
, iPod nano
®
, iPhone
®
, and Lightning
™
are trademarks of Apple Inc.,
registered in the U.S. and other countries. The trademark “iPhone” is used in Japan with
a license from Aiphone K.K.
App Store
SM
is a service mark of Apple Inc. Bluetooth
®
word
mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by
Garmin is under license. HDMI
®
is a registered trademark of HDMI Licensing, LLC. ,
NMEA 2000
®
and the NMEA 2000 logo are registered trademarks of the National Marine
Electronics Association. Sirius, XM and all related marks and logos are trademarks of
Sirius XM Radio Inc. Other trademarks and trade names are those of their respective
owners.
FUSION MS-UD/AV650/755 Installation Instructions 5
www.fusionentertainment.com
TA-2016/3483
TA-2017/1872
TA-2017/1873
-
1
-
2
-
3
-
4
-
5
-
6
Fusion MS-AV650 Guida d'installazione
- Tipo
- Guida d'installazione
in altre lingue
- English: Fusion MS-AV650 Installation guide
Documenti correlati
-
Fusion Fusion Apollo RA770 Guida d'installazione
-
Fusion MS-UD650 Guida d'installazione
-
Fusion MS-UD/AV750 Manuale del proprietario
-
Fusion Marine Black Box Guida d'installazione
-
Fusion MS-RA70N Guida d'installazione
-
-
Fusion SG-DA61500 Manuale utente
-
Fusion SG-DA82000 Manuale utente
-
-
Fusion XS-S10CWB Guida d'installazione