LG WD-12590BD Manuale utente

Washing Machine

OWNER'S MANUAL (2P~29P)

WD-1259(0~9)BD

Thank you for buying a

LG Fully Automatic Washing machine.

Please read your owner's manual carefully, it provides

instructions on safe installation, use and maintenance.

Retain it for future reference.

Record the model and serial numbers of your washing

machine.

Lavatrice

MANUALE D’USO (30P~59P)

roduct Feature

P

ontents

C

2

Warnings ......................................................................................................................3

Specification...................................................................................................................4

Installation......................................................................................................................5

Care before washing....................................................................................................10

Adding detergent..........................................................................................................11

Function ....................................................................................................................13

How to use washer ......................................................................................................14

Maintenance ................................................................................................................22

Troubleshooting guide .................................................................................................25

Terms of Warranty .......................................................................................................29

 Direct Drive System

The advanced Brushless DC motor directly drives the drum without

belt and pulley.

 Water Circulation

Sprays detergent solution and water onto the load over and over.

Clothes are soaked more quickly and thoroughly during wash cycle.

The detergent suds can be removed more easily by the water shower during rinse

cycle. The water circulation system uses both water and detergent more efficiently.

 Tilted Drum and Extra Large Door Opening

Tilted drum and extra large opening make it possible to load

and unload clothing more easily.

 Automatic Wash Load Detection

Automatically detects the load and optimizes the washing time.

 Built-in Heater

Internal heater helps to maintain water temperature at its optimum level for

selected cycles.

 Child Lock

The Child lock prevents children from pressing any button to change the settings

during operation.

 

arnings

W

3

For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, electric shock, or to prevent property damage,

personal injury, or loss of life.



READ ALL INSTRUCTIONS BEFORE USE

WARNING!

• Do not install or store the washer where it will

be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer

or attempt any servicing unless specifically

recommended in the user-maintenance

instructions or published user-repair instructions

that you understand and have the skills to carry

out.

• Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is

used by or near children or infirm persons.

Do not allow them to play on, with, or inside this

or any other appliance.

• Keep washer away from fire.

• Do not leave the washer door open.

An open door could entice children to hang on

the door or crawl inside the washer.

• Never reach into washer while it is moving. Wait

until the drum has completely stopped.

• The laundry process can reduce the flame

retardant of fabrics.

• Do not wash or dry articles that have been

cleaned in, washed in, soaked in, or spotted with

combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dry cleaning

solvents, kerosene, etc.) which may ignite or

explode.

Oil may remain in the tub after a whole

cycle resulting in fire during drying. So, do not

load oiled clothes.

• Always follow the fabric care instructions

supplied by the garment manufacturer.

• Do not slam the washer door closed or try to

force the door open when locked. This could

result in damage to the washer.

• To minimize the possibility of electric shock,

unplug this appliance from the power supply or

disconnect the washer at the household

distribution panel by removing the fuse or

switching off the circuit breaker before attempting

any maintenance or cleaning.

• Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

• Dryer is intended for only drying textile material.

• If the washer has been exposed to water, call an

authorized service provider to avoid any risk of

fire or electric shock.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. This appliance is equipped with

a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter or otherwise defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : To reduce the risk of fire, electric shock, or injury to persons when using

the washer, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

WARNING : Improper connection of the equipment-grounding conductor can result in risk of electric

shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is

properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a

proper outlet installed by a qualified electrician.

4

pecification

S

 Name : Front loading washing machine

 Power supply : 220-240 V~, 50Hz

 Size : 635 mm(L) x 740 mm(P) x 925 mm(H)

 Weight : 76kg

 Wash capacity : 10kg

 Max. Watt : 2200W

 Spin speed : 0/400/800/1000/1200

 Water consumption : 79

(7.9/ kg )

 Permissible water pressure : 0.3~10 kgf/cm

2

(30~1000 kPa)

❋ The appearance and specifications may be varied without notice to improve the units quality.

❋ Specifications subject to change by manufacturer.



Accessories

Drum

Drain Plug

Drain Pump Filter

Lower cover cap

Door

Adjustable Feet

Drain Hose

Control Panel

Shipping Bolts

Power Plug

• If the supply cord is damaged,

it must be replaced by the

manufacturer or its authorized

service technician in order to

avoid a hazard.

Dispenser

Inlet hose (1EA) Spanner

5

nstallation

I

1. To prevent internal damage during

transport, the special 4 bolts are locked.

Before operating the washer, remove

the bolts along with the rubber bungs.

• If they are not removed, it may cause

heavy vibration, noise and malfunction.

3. Take out the 4 bolts along with the

rubber bungs by slightly twisting the

bung. Keep the 4 bolts and the spanner

for future use.

• Whenever the appliance is transported,

the transit bolts must be refitted.

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be

removed before using the washer.

󳀙 When unpacking the base, be sure to

remove the additional packing support

in the middle of the base packing.

2. Unscrew the 4 bolts with

the spanner supplied.

4. Close the holes with the caps supplied.



Transit bolts

Install or store where it will not be exposed to temperatures below freezing or exposed to the

weather.

Properly ground washer to conform with all governing codes and ordinances.

The base opening must not be obstructed by carpeting when the washing machine is installed on

a carpeted floor.

In countries where there are areas which may be subject to infestation by cockroaches or other

vermin, pay particular attention to keeping the appliance and its surroundings in clean

condition at all times.

Any damage which may be cause by cockroaches or other vermin will not be covered by the

appliance guarantee.



Removing transit bolts

Washer

Base Packing

Packing Support

6

nstallation

I

Level floor :

Allowable slope under entire washer is 1°

Power outlet :

Must be within 1.5 meters of either side of location of

washer. Do not overload the outlet with more than one

appliance.

Additional Clearance :

For wall, door and floor modeling is required.

(10cm : rear / 2cm : right & left side)

Do not place or store laundry products on top of

washer at any times.

They can damage the finish or controls.



Installation place requirement



Positioning

Install the washer on a flat hard floor.

Make sure that air circulation around the washer is not impeded by carpets,rug etc.

• Before placing the washer on tiles, apply a rubber mat under the feet.

• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar

materials under the washer.

• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an

insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be

inserted between the two appliance.

• The washer must not be installed in rooms where the temperature can drop below 0°C.

• Please ensure that when the washer is installed, it is easily accessible for the engineer in the

event of a breakdown.

• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the

appliance is stable, and a clearance of approximately 20mm is left between the top of the washer

and the underside of the work-top.

• The installation instructions shall state that the openings must not be obstructed by a carpet if it

has ventilation openings in the base.

Washer

Drain Hose

Laundry

Tub

approx.

2cm

7

nstallation

I



Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm

2

)



Don’t strip or crossthread when connecting Inlet hose to the valve.



If the water supply pressure is more than 800kPa, a decompression device

should be installed.

• Two rubber seals are supplied with the water inlet hoses these are in

order to prevent water leaks.

• Check water tightness of washing machine connections by turning

the tap completely on.

• Periodically check the condition of the hose and replace the hose if

necessary.

• Make sure that there is no kink on the hose and that it is not crushed.

• The instructions for appliances connected to the water mains by

detachable hose-sets shall state that the new hose-sets supplied with

the appliance are to be used and that old hose-sets should not be

reused.



When your washer has two valves,

• If the washer has two valves, the energy is saved by using hot valve.



Washing Machine is to be connected to the water mains using new hose-sets and that old

hose-sets should not be used.



Connecting water supply hose

1. Do not use an extension cord or double adapter.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly

qualified person in order to avoid a hazard.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by inexperienced

persons may cause injury or serious malfunctioning. Contact your local service center

• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst

under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing machine

at room temperature for a few hours before putting it into operation.



Electrical connection

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit

which powers only that appliance and has no additional outlets or branch circuits. Check the

specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,

frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions

could result in electric shock or fire. Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have

the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,

closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where

the cord exits the appliance.

If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord

extension set or electrical portable outlet device must be positioned so that it is not subject to

splashing or ingress of moisture.

CAUTION

Hose connector

Sealing

washer

Cold

water tap

8

nstallation

I



Installation of drain hose

• The drain hose end should not be placed

higher than 100 cm above the floor.

• Proper securing of the drain hose will

protect the floor from damage due to water

leakage.

• When the drain hose is too long, do not

force back into the washer. This will cause

abnormal noise, malfunction, and water

leakage.

• When installing the drain hose to a sink,

secure it tightly with a string.

• Proper securing of the drain hose will

protect the floor from damage due to water

leakage should the drain hose become

loose.

This equipment is not designed for maritime use or for use mobile installations such as

caravans, aircraft etc.

Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),

especially if there is no floor drain(gully) in the immediate vicinity.

When disposing of the appliance, cut off the mains cable, and destroy the Plug.

Disable the door lock to prevent young children being trapped inside.

Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of

suffocation ! Keep all packaging well away from children

about 100 cm

Laundry tub

Hose

Retainer

Tie

strap

max. 100cm

min. 60cm

max. 100cm

min. 60cm

about 105 cm

max. 100 cm

min. 60 cm

about 145 cm

9

nstallation

I

 Concrete floors

 Wooden floors (Suspended floors)

• The installation surface must be clean, dry and level.

• Install washer on a flat hard floor.

 Tile floors (Slippery floors)

• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into

70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)



Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

• Wooden floors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each

foot, at least 15mm thick under the washer, secured to at least 2 floor

beams with screws.

• If possible install the washer in one of the corners of the room, where the floor is more stable.



Insert the rubber cups to reduce vibration.



Rubber cups ( p/no. 4620ER4002A) can be purchased from the LG spare parts department.

Important!

• Proper placement and levelling of the washer ensures long, regular and reliable operation.

• The washer must be absolutely horizontal and stand firmly in position.

• It must not “Seesaw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.



It can be purchased from

hardware suppliers.



Level adjustment

1. Adjusting the washing machine level properly prevents excessive

noise and vibration.

Install the appliance on a solid and level floor surface, preferably in

a corner of the room.

2. If the floor is uneven, adjust the adjustable feet as required. (do

not insert pieces of wood etc. under the feet)

Make sure that all four feet are stable and resting on the floor and

then check that the appliance is perfectly level. (use a spirit level)



After the washer is level, tighten the lock nuts up towards of the base of

the washer. All lock nuts must be tightened.

❊ Diagonal Check

When pushing down the edges of the washing machine top plate diagonally, the

machine should not move up and down at all. (Please, check both of two directions)

If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

NOTE

Timber or suspended type flooring may contribute to

excessive vibration and unblance errors.

NOTE

In the case that the washing machine is installed on a raised

platform, it must be securely fastened in order

to eliminate the risk that it might fall off.

Lock nut

Adjustable feet

Rubber Cup

Adjustable feet Adjustable feet

Higher

Lower

10

are before washing

C

1. Care Labels

Look for a care label on your clothes. This will tell you about the fabric content of your garment and

how it should be washed.

2. Sorting

To get the best results, Sort clothes into loads that can be washed with the same wash cycle.

Water temperature and spin speed and different fabrics need to be washed in different ways.

Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can

occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly

soiled one.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.

Color (White, Lights, Darks) Separate white fabrics from colored fabrics.

Lint (Lint producers, Collectors) Wash lint producers and lint collectors

separately.

3. Caring before loading



Caring before washing



Before the first washing

 Combine large and small items in a load. Load large items first. Large items should not be more

than half the total wash load.

Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing.

This will remove residues from the drum that may have been left during manufacturing.

• Check all pockets to make sure that they are

empty. Items such as nails, hair clip,

matches, pens, coins and keys can damage

both your washer and your clothes.

• Close zippers, hooks and strings to make

sure that these items don’t snag on other

clothes.

• Do not be stuck between the door and the

glass.

• Pre treat dirt and stains by brushing a little

detergent dissolved in water onto stains like

collars and cuffs to help shift dirt.

• If you wash underwear, use the wash cloth

bag. If you don’t use the wash cloth bag while

washing the underwear, wires in the bra may

make a noise.

11

dding detergent

A

• Main wash only

➔

• Pre Wash + Main Wash

➔

• Do not exceed the maximum fill line.

Close the dispenser drawer slowly.

Overfilling can cause early dispensing

of the fabric softener which could stain

clothes.

• Do not leave the fabric softener in the

detergent drawer for more than 2 days.

(Fabric softener could harden)

• Softener will automatically be added

during the last rinse cycle.

• Do not open the drawer when water is

supplied.

• Solvents(benzene, etc) are not

allowable.

1. The Dispenser Drawer

2. Adding Fabric Softener



Adding detergent and fabric softener

Do not pour fabric softener

directly on the cloths

NOTE

( )

Detergent for

main wash

Fabric

softener

Detergent for

pre wash

12

dding detergent

A

• The detergent should be used according to the

instruction of the detergent manufacture.

• If too much detergent is used, too many suds can

occur and this will decrease the washing result

or cause heavy load to the motor.

• Use powder detergent only for the front loading

washer.

❇

If suds occur too much, pleas reduce the

detergent amount.

• Detergent usage may need to be adjusted

for water temperature, water hardness, size

and soil level of the load. For best results,

avoid oversudsing.

4. Water softener

• A water softener, such as Anti limescale

(Clagon) can be used to cut down on the

use of detergent in extremely hard water

areas. Dispense according to the amount

specified on the packaging.

First add detergent and then the water

softener.

• Use the quantity of detergent as for soft

water.

❋

Tips

Full load : according to manufacturer’s

recommendation.

Part load : 3/4 of the normal amount.

Minimum load : 1/2 of full load.

• Detergent is flushed from the dispenser at

the beginning of the cycle.

3. Detergent dosage

1) Open the door and Tablets into the

drum.

5. Using the Tablets

2) Load the laundry into the drum.

3) Close the door.

13

unction

F



Recommended courses according to the laundry type

❋ Water Temperature: Select the water temperature to the wash cycles. Always follow garment

manufacture’s care label or instructions when laundering.

❋ Intensive: When washing full load or heavily soiled laundry, you can increase effectiveness by choosing

intensive option.

❋ Pre Wash: If the laundry is heavily soiled, “Pre Wash” option is recommended.

Pre Wash is available in Cotton, Contton-Eco, Baby Care, Cotton Quick and Synthetic.

Cotton

Color fast garments (shirts, night

dresses, pajamas...) and lightly soiled

white cotton (underwear...)

- Pre wash

- Rinse+Spin

- Spin Only

- Bio

- Soak

- Intensive

- Water Plus

- Pre wash

- Rinse+Spin

- Spin Only

- Soak

- Intensive

- Water Plus

60°C

(Cold, 30°C,

40°C, 95°C)

Cotton-Eco Laundry type is the same in Cotton.

Synthetic

Polyamide, Acrylic, Polyester.

40°C

(Cold, 30°C,

60°C)

Nominal

Less than

5,0kg

- Pre wash

- Rinse+Spin

- Spin Only

- Bio

- Soak

- Intensive

- Water Plus

Baby Care Lightly soiled baby wear

95°C

(40°C, 60°C)

Less than

6,0kg

Nominal

Less than

4,0kg

Less than

3,0kg

Less than

5,0kg

Maximum

load

9.0kg

- Pre wash

- Rinse+Spin

- Spin Only

- Soak

- Intensive

- Water Plus

- Pre wash

- Spin Only

- Intensive

- Rinse+Spin

- Spin Only

- Intensive

- Water Plus

40°C

(Cold, 30°C,

60°C, 95°C)

Cotton

Quick

Cotton which is lightly soiled.

Delicate Delicate laundry easily damaged.

40°C

(Cold, 30°C)

Hand Wash

/Wool

“Hand Wash” marked laundry or machine

washable woolens.

30°C

(Cold, 40°C)

Quick 30

Colored Landry which is lightly soiled fast.

Duvet

Cotton bedding with filling, duvet, pillow,

blanket, sofa cover with light filling.

40°C

(Cold, 30°C)

Maximum

Load

Additional

Option

Proper Temp.

(Option)

Fabric Type

Program

14

ow to use washer

H

• Press the Power( ) button to start.

• Press the Start/Pause( ) button.

• Initial condition

- Rinse : 3 times

- Water temperature : 60°C

- Spin : 1200 rpm

- Program : Cotton

• Press the Power( ) button to turn the

washer on.

• Select the desired cycle with the program

dial and if required, make any changes to

the washing conditions by pressing the

buttons accordingly.

For selecting the each conditions, please refer

to the page15~page21

• Press the Start/Pause button to

commence the cycle.

1. Cotton automatically

selected upon power on.

2. Manual Selecting

15

ow to use washer

H

ProgramPower

• Press the Power( ) button to turn power

on and off.

• To cancel the Time Delay function, the

Power( ) button must be pressed.

• When the Power( ) button is pressed, the

washer is ready for Cotton program. And the

other initial conditions as follows.

• So, if you want to advance into the washing

cycle without changing the program, just

press Start/Pause( ) button and then the

washer will proceed.

■

Initial program

- Cotton Program / Rinse:Normal / 60°C/

1200rpm

(1)Button: Power

(2)Dial: Program

(3)Button: Start/Pause

(4)Button: Option

(5)Child lock

(6)Button: Rinse

(7)Button: Temp.

(8)Button: Intensive

(9)Button: Water Plus

(10)Button: Time Delay

(11)Button: Beeper

(12)Button: Tub Clean

(13)Dial: Spin

• 9 programs are available according to the

laundry type.

• Dial lamp will light up to indicate selected

program.

• When Start/Pause( ) button is pressed,

the Cotton program is automatically

selected.

- By turning the Program dial, the program is

Selected in order of “Cotton - Cotton Quick -

Synthetic - Delicate - Hand Wash/Wool -

Duvet - Quick 30 - Baby Care - Cotton-Eco”.

For information regarding laundry type for

each program, please refer to page 13.

1. Power

2. Initial Program

(1) (3) (4) (6) (7) (11) (12)(8,9,10) (13)(5)(2)

16

ow to use washer

H

Option

• By pressing the option

button, only one option

function may be selected.

NOTE:

Depending on the selected

program cycle, not all

Options may be selectable.

Start/Pause

• This Start/Pause button is used to start

wash cycle or pause the wash cycle.

• If temporary stop of wash cycle is needed,

press “Start/Pause” button.

• When in Pause, the power is turned off

automatically after 4 minutes.

1. Start

• Use this option for loads that need

pretreatment. This adds 16 minutes of pre

washing before draining.

- When using Pre Wash option, do not use a

liquid detergent for the main wash.

Use powder for the main wash.

1. Pre Wash

• Use this option to rinse and then spin

2. Rinse + Spin

• When you want spin only, select this option.

3. Spin Only

• If you want to eliminate protein stains(milk,

blood, chocolate...), you may select Bio

function by pressing the option button.

NB. You can select Bio function when

temperature is higher than 60󰝝C in Cotton,

Cotton-Eco, Baby Care.

4. Bio

• Use this mode to wash normal clothes or thick

and heavy clothes which are excessively dirty.

5. Soak

2. Pause

Door Lock

• Lights whenever the door of the washer is

locked.

• The door can be unlocked by pressing the

Start/Pause button to stop the washer.

• The door can be opened after a short delay.

Detecting

• While the "Detecting" is shown in the display

the machine rotates slowly and detects how

many laundries are loaded in the drum. It

will take a few seconds.

17

ow to use washer

H

Rinse

• By pressing the Rinse

button, the Rinse type can

be selected.

- Normal

- Rinse

+

- Medic Rinse

- Normal+Hold

- Rinse

+

+Hold

• Cotton, Cotton-Eco, Synthetic, Baby Care

performs 3 Rinses

• Quick 30, Hand Wash/Wool, Duvet, Delicate

Cotton Quick performs 2 Rinses.

• Used to additional rinse, which may assist in

removing traces of detergent residue.

• By selecting Rinse

+

or Medic Rinse

function, the Rinse Time and the Rinse

water are increased.

• Medic Rinse heats the water to 40 Deg in

the last rinse.

• Is selected by pressing the Rinse button

repeatedly this function leaves clothes in the

washer; suspended in the water after a rinse

without entering into spin.

• To proceed to a Drain or Spin function after

a Rinse hold, select Drain on the program

dial or press the Spin button for the desired

speed, then press the Start/Pause button.

The matching indicator lamp will light up for

identification.

Child lock

If you choose to lock the buttons on the

control assembly to prevent tampering, this

function may be selected.

• Child lock can be set by pressing and

holding the Option and Rinse button

simultaneously. (About three seconds)

• When child lock is set, all buttons are

inoperable.

• To deactivate Child lock system, press and

hold the Option and Rinse button

simultaneously again.

(About three seconds)

• To change to the desired program, whilst in

child lock mode.

1. Press and hold both Option and Rinse

button to cancel the child lock.

(About three seconds)

2. Press the Start/Pause button.

3. Select the desired program and press the

Start/Pause button again.

• The child lock can be set at any time and it

is automatically canceled when operational

errors occur.

1. Normal

2. Rinse

+

& Medic Rinse

3. Rinse Hold

Change

the desired

program

18

Intensive

• When washing full load or heavily soiled

laundry, you can increase effectiveness by

choosing intensive option.

• By selecting the Intensive option, the wash

time may be extended, depending on the

program selected.

• To use this option press the Intensive button

once before the wash program is started.

ow to use washer

H

Water Temperature

• By pressing the Temp.

button, the water

temperature can be

selected.

- Cold

- 30˚C / 40˚C / 60˚C / 95˚C

• Water temperature can be selected as

below according to the program.

- Cotton & Cotton Quick & Cotton-Eco

Cold- 30°C - 40°C - 60°C - 95°C

- Synthetic

Cold - 30°C - 40°C - 60°C

- Delicate & Quick 30 & Duvet & Hand

Wash/Wool

Cold - 30°C - 40°C

- Baby Care

40°C - 60°C - 95°C

The required temperature lamp will light up for

identification.

For the more detailed information, please refer

to the page13.

• Adds extra water to the wash and rinse

cycles for superior results.

Water Plus

19

ow to use washer

H

Tub Clean

Tub Clean course can be set by pressing

‘Tub Clean’ button.

TUB CLEAN is special cycle to clean the

inside of the washer. This cycle uses higher

water level with higher spin speed. Perform

this cycle regularly.

How to use the Tub Clean cycle:

1. Remove any clothing or items from the

washer and close the door.

2. Open the dispenser drawer and add Anti

limescale (Calgon) to the Main wash

compartment.

NOTE: Do not add any detergent to the

detergent compartments. Excessive

suds may generate and leak from the

washer.

3. Close the dispenser drawer slowly.

4. Power On and then press ‘Tub Clean’

5. Press the Start/Pause button to start.

6. After the cycle is complete, leave the door

open to dry around the washer door

opening, flexible gasket and door glass.

CAUTION

If there is a small child, be careful not to

leave the door open for too long.

!

Time Delay

Preparing washing before starting “Time Delay”

- Turn on the water tap.

- Load laundry and close the door.

- Place the detergent and fabric softener in

the drawer.

• How to set “Time Delay”

- Press Power( ) button.

- Turn the Program dial to select

the program you require.

- Press Time Delay button and set the

desired time.

- Press the Start/Pause( ) button.

(“ ” lamp is blink)

• If Time Delay button is pressed, “3:00” is

displayed. The maximum delayed time is

19:00 hours and the minimum time is 3:00

hours.

• Each pressing of the button advances time

delay by one hour.

• To cancel the time delay, press the

Power( ) button.

• Time Delay is ‘expected time’ from the

present to the completion of washing cycle

or selected process (Wash, Rinse, Spin).

• According to the condition of water supply and

temperature, the delayed time and the actual

washing time may vary.

ow to use washer

H

20

Beeper

The matching indicator lamp will light up for

identification.

Spin

• By pressing the Spin button, the spin speed

can be chosen.

• Press repeatedly to adjust

the volume of the Beeper.

- Cotton & Cotton-Eco & Quick 30 & Cotton

Quick

0 – 400 – 800 – 1000 – 1200

- Baby Care & Duvet & Synthetic & Hand

Wash/Wool

0 – 400 – 800 – 1000

- Delicate

0 – 400 – 800

• If “No Spin” is selected, the washer stops

after draining the water from the last spin.

1. Press the Power buton.

2. Set the desired spin speed by pressing the

Spin button.

3. Press the Start/Pause button.

The matching indicator lamp will light up for

identification.

1. Spin selection

2. No spin

3. Spin Only

La pagina sta caricando ...

LG WD-12590BD Manuale utente

Questo manuale è adatto anche per

LG WD-12590BD Manuale utente

in altre lingue

Documenti correlati