HP c7000 Manuale utente

HP BladeSystem c7000 Enclosure

Setup and Installation Guide

Abstract

This guide describes identification, operations, setup, configuration and utilities, troubleshooting, regulatory notices, specifications, and technical

support. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in

recognizing hazards in products, and are familiar with weight and stability precautions.

Part Number: 411272-401

February 2013

Edition: 10

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Contents 3

Contents

Planning the installation ................................................................................................................. 6

Verifying the pallet contents ........................................................................................................................ 6

Rack requirements ..................................................................................................................................... 7

Rack-free environment requirements ............................................................................................................. 8

Warning, caution, and important messages .................................................................................................. 8

Space and airflow requirements ................................................................................................................ 10

Temperature requirements ........................................................................................................................ 11

Power requirements ................................................................................................................................. 11

Grounding requirements ........................................................................................................................... 11

Component and LED identification ................................................................................................ 12

Enclosure front components ...................................................................................................................... 12

Power supply bay numbering .......................................................................................................... 13

Power supply LEDs ......................................................................................................................... 13

Device bay numbering ................................................................................................................... 14

HP BladeSystem Insight Display components ..................................................................................... 15

Location Discovery Services ............................................................................................................ 15

Enclosure rear components ....................................................................................................................... 16

Fan bay numbering ....................................................................................................................... 17

Fan LED ........................................................................................................................................ 18

Onboard Administrator components ................................................................................................ 18

HP c7000 Onboard Administrator with KVM components .................................................................. 19

Interconnect bay numbering ............................................................................................................ 20

Installation ................................................................................................................................. 21

Installation overview ................................................................................................................................ 21

Disassembling the enclosure ..................................................................................................................... 21

Rack-free installation ................................................................................................................................ 24

Rack installation ...................................................................................................................................... 24

Measuring with the rack template .................................................................................................... 25

Installing the rack rails .................................................................................................................... 25

Installing the enclosure into the rack ................................................................................................. 26

Installing the rear cage into the enclosure ......................................................................................... 28

Component installation ............................................................................................................................ 29

Installing a power supply ................................................................................................................ 29

Installing blades ............................................................................................................................ 31

Connecting locally to a server blade with video and USB devices ........................................................ 40

Installing fans ................................................................................................................................ 42

Installing Onboard Administrator modules ........................................................................................ 44

Installing interconnect modules ........................................................................................................ 46

Cabling and powering up the enclosure ........................................................................................ 56

Cabling the enclosure .............................................................................................................................. 56

Onboard Administrator cabling ....................................................................................................... 56

Enclosure link cabling .................................................................................................................... 57

Cabling a PC to the enclosure service port ........................................................................................ 58

Cabling the network to the enclosure ............................................................................................... 59

Contents 4

Powering up the enclosure ........................................................................................................................ 59

Single-phase AC configuration ........................................................................................................ 59

Three-phase AC configuration ......................................................................................................... 64

HP BladeSystem Insight Display .................................................................................................... 65

Insight Display overview ........................................................................................................................... 65

Running the Insight Display installation steps ............................................................................................... 65

Navigating the Insight Display .................................................................................................................. 69

Health Summary screen .................................................................................................................. 70

Enclosure Settings screen ................................................................................................................ 73

Enclosure Info screen ..................................................................................................................... 73

Blade and Port Info screen .............................................................................................................. 74

Turn Enclosure UID On/Off screen ................................................................................................... 75

View User Note screen ................................................................................................................... 77

Chat Mode screen ......................................................................................................................... 77

Troubleshooting .......................................................................................................................... 78

Troubleshooting resources ........................................................................................................................ 78

Important safety information ...................................................................................................................... 78

Symbols on equipment ................................................................................................................... 78

Warnings and cautions .................................................................................................................. 79

Insight Display errors ............................................................................................................................... 80

Power errors ................................................................................................................................. 80

Cooling errors ............................................................................................................................... 81

Location errors .............................................................................................................................. 81

Configuration errors ....................................................................................................................... 81

Device failure errors ....................................................................................................................... 81

Support and other resources ........................................................................................................ 83

Before you contact HP .............................................................................................................................. 83

HP contact information ............................................................................................................................. 83

Customer Self Repair ............................................................................................................................... 83

Regulatory compliance notices ..................................................................................................... 91

Regulatory compliance identification numbers ............................................................................................. 91

Federal Communications Commission notice ............................................................................................... 91

FCC rating label ............................................................................................................................ 91

FCC Notice, Class A Equipment ...................................................................................................... 91

FCC Notice, Class B Equipment ...................................................................................................... 91

Declaration of conformity for products marked with the FCC logo, United States only ....................................... 92

Modifications .......................................................................................................................................... 92

Cables ................................................................................................................................................... 92

Canadian notice (Avis Canadien) .............................................................................................................. 92

European Union regulatory notice ............................................................................................................. 93

Disposal of waste equipment by users in private households in the European Union ......................................... 93

Japanese notice ...................................................................................................................................... 94

BSMI notice ............................................................................................................................................ 94

Korean notice ......................................................................................................................................... 94

Chinese notice ........................................................................................................................................ 95

Laser compliance .................................................................................................................................... 95

Battery replacement notice ........................................................................................................................ 95

Taiwan battery recycling notice ................................................................................................................. 96

Power cord statement for Japan ................................................................................................................. 96

Electrostatic discharge ................................................................................................................. 97

Contents 5

Preventing electrostatic discharge .............................................................................................................. 97

Grounding methods to prevent electrostatic discharge .................................................................................. 97

Acronyms and abbreviations ........................................................................................................ 98

Documentation feedback ........................................................................................................... 100

Index ....................................................................................................................................... 101

Planning the installation 6

Planning the installation

Verifying the pallet contents

Item Name Description

1

HP BladeSystem c7000 Enclosure The HP BladeSystem enclosure

2

Rear cage The rear section of the enclosure

3

Device bay blank A mandatory insert installed in any unused device bay

4

Power supply blank A mandatory insert installed in any unused power

supply bay

5

Enclosure hot-plug power supply (quantity

as ordered)

The power supply for the enclosure

6

Full-height device (quantity as ordered) The full-height server or storage blade

7

Half-height device (quantity as ordered) The half-height server or storage blade

8

Local I/O cable A cable with serial, USB, and video connectors that

connects to the I/O connector on the front of a blade

9

Fan blank A mandatory insert installed in any unused fan bay

10

HP Active Cool 200 Fan (quantity as

ordered)

A fan used to cool the components installed in the

enclosure

Planning the installation 7

Item Name Description

11

Onboard Administrator module Hot-pluggable enclosure management module. One

module is required to manage the components

installed in the enclosure. To provide redundant

enclosure management, you can install an optional

second module.

12

Onboard Administrator blank A mandatory cover installed in any unused Onboard

Administrator bay

13

Interconnect blank A mandatory insert installed in any unused

interconnect bay

14

Interconnect module (quantity and type as

ordered)

Any of several components, such as pass-thrus or

switches that enable communication between the

blade and the enclosure

15

Onboard Administrator tray Hot-pluggable tray that houses up to two Onboard

Administrator modules and provides two enclosure link

connectors, the rear enclosure UID, LED, and switch.

16

HP BladeSystem Insight Display A display that provides information about the health

and operation of the enclosure

17*

Power retention ties (single-phase enclosures

only)

Tie straps that help prevent single-phase power cables

from disconnecting from the power connectors

18*

Documentation CD A CD containing detailed documentation on using the

enclosure

19*

Hard copy installation instructions for

blades, options, and interconnects

The printed installation instructions

20*

Installation checklist A checklist to guide you through installation of the

enclosure and components

* Not shown

Rack requirements

The enclosure is compatible with the following racks:

• All HP 10000 and 10000G2 Series racks except the HP 10614 rack.

NOTE: The system is optimized for 10000 Series racks.

• Telco racks

• Third-party rack cabinets that meet the following requirements:

o Width: 48.3 cm (19 in)

o Depth:

— 88.9 cm (35 in) maximum clearance between front and rear RETMA rails

— 62.7 cm (24.7 in) minimum clearance for round-hole racks

— 63.5 cm (25 in) minimum clearance for square-hole racks

o Clearance—7.6 cm (3 in) minimum clearance between rear RETMA rails and rear rack door to

accommodate system cabling

o Clearance—4.5 cm (1.75 in) minimum clearance between rack face and inside of front rack door

Planning the installation 8

o

Open area—Minimum of 65 percent open area to provide adequate airflow through any rack front

or rear doors

o Adjustable rack rails are shipped with each enclosure:

— Minimum rail length: 63.5 cm (25 in)

— Maximum rail length: 86.4 cm (34 in)

Rack-free environment requirements

The HP BladeSystem c7000 Enclosure (referred to as the enclosure) can be used in a rack-free environment.

The following conditions must be met when performing a rack-free installation:

• A fully-populated enclosure can weigh up to 217.7 kg (480 lb). The object supporting the enclosure

must be able to withstand this weight.

• The enclosure should be supported by a sturdy, flat surface.

WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free

environment:

• Never stack the enclosure on top of another enclosure.

• Never place equipment on top of the enclosure.

• Never place the enclosure on a surface that cannot support up to 217.7 kg (480 lb).

Warning, caution, and important messages

WARNING: To reduce the risk of personal injury or damage to equipment, heed all warnings

and cautions throughout the installation instructions.

WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that:

• The leveling jacks are extended to the floor.

• The full weight of the rack rests on the leveling jacks.

• The stabilizing feet are attached to the rack if it is a single-rack installation.

• The racks are coupled together in multiple-rack installations.

• Only one component is extended at a time. A rack may become unstable if more than one

component is extended for any reason.

WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack:

• At least two people are needed to safely unload the rack from the pallet. An empty 42U rack

can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and might

become unstable when being moved on its casters.

• Never stand in front of the rack when it is rolling down the ramp from the pallet. Always handle

the rack from both sides.

Planning the installation 9

WARNING:

The enclosure is very heavy. To reduce the risk of personal injury or damage to the

equipment:

• Observe local occupational health and safety requirements and guidelines for manual

material handling.

• Remove all installed enclosure components from their enclosures before installing or moving

the enclosures.

• Use caution and get help to lift and stabilize enclosures during installation or removal,

especially when the enclosure is not fastened to the rack.

WARNING: To reduce the risk of personal injury or damage to the equipment, you must

adequately support enclosures during installation and removal.

WARNING: Always use at least two people to lift an enclosure into the rack. If the enclosure is

being loaded into the rack above chest level, a third person must assist with aligning the enclosure

with the rails while the other two people support the weight of the enclosure.

WARNING: Before installing an enclosure in the rack, be sure that all hot-plug power supplies,

server blades, and interconnects are removed from the enclosure. Blanks can be left in the

enclosure.

WARNING: Be sure to install enclosures starting from the bottom of the rack and work your way

up the rack.

These symbols, on power supplies or systems, indicate that the equipment is supplied by

multiple sources of power.

WARNING: To reduce the risk of injury from electric shock, remove all power cords to

completely disconnect power from the system.

• Each enclosure has two or more power supply cords. A single rack or cabinet may

contain more than one enclosure. Power may be supplied in a redundant fashion.

Removing any single source of power does not necessarily remove power from any

portion of the system. When performing any service other than hot-plug module

replacement, you must completely disconnect all power to that portion of the system.

• When performing service procedures on enclosures, shut off the circuit breakers to

both A and B AC power feeds and then disconnect all power cords from the outlets

before servicing.

WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

WARNING:

To reduce the risk of electric shock or damage to the equipment, enter enclosures or

perform service on system components only as instructed in the user documentation.

WARNING: A risk of electric shock from high leakage current exists. Before connecting the AC

supply to the power enclosures, be sure that the electrical outlets are properly grounded (earthed).

CAUTION: Always be sure that equipment is properly grounded and that you follow proper

grounding procedures before beginning any installation procedure. Improper grounding can

result in ESD damage to electronic components. For more information, refer to, "Electrostatic

discharge (on page 97)."

Planning the installation 10

CAUTION: When performing non-hot-plug operations, you must power down the server blade

and/or the system. Use caution when performing other operations, such as hot-plug installations

or troubleshooting.

CAUTION: Protect the equipment from AC power fluctuations and temporary interruptions with a

regulating facility UPS device. This device protects the hardware from damage caused by power

surges and voltage spikes and keeps the system in operation during a power failure.

IMPORTANT: Data on the dimensions and weights of HP BladeSystem c-Class components can

be found in the HP BladeSystem c-Class Maintenance and Service Guide. The same data can be

determined by using the online HP BladeSystem c-Class Sizing Utility.

Space and airflow requirements

To enable servicing and ensure adequate airflow, observe the following spatial requirements when deciding

where to install an HP branded, Compaq branded, telco, or third-party rack:

• Leave a minimum clearance of 63.5 cm (25 in) in front of the rack.

• Leave a minimum clearance of 76.2 cm (30 in) in back of the rack.

• Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the rear of another rack

or row of racks.

HP BladeSystem servers draw cool air in through the front and expel warm air through the rear of the

enclosure. Therefore, the front of the rack enclosure must be adequately ventilated to enable ambient room

air to enter the enclosure, and the rear of the enclosure must be adequately ventilated to enable the warm air

to escape from the enclosure.

IMPORTANT: Do not block the ventilation openings.

If the front of the rack is not completely filled with components, the remaining gaps between the components

can cause changes in the airflow, which can adversely affect cooling within the rack. Cover these gaps with

blanking panels.

CAUTION: Always use blanking panels to fill empty vertical spaces in the rack. This arrangement

ensures proper airflow. Using a rack without blanking panels results in improper cooling that can

lead to thermal damage.

In high density configurations, the HP 10000 Series Rack Airflow Optimization Kit (AF090A) should be

installed to prevent airflow from the rear of the rack to the front the rack via gaps in the rack frame.

HP 10000 Series and 10000 G2 Series racks provide proper server cooling from flow-through perforations

in the front and rear doors that provide 65 percent open area for ventilation.

CAUTION: Always use blanks to fill empty spaces in enclosures. This arrangement ensures

proper airflow. Using an enclosure without the proper blanks results in improper cooling that can

lead to thermal damage.

Planning the installation 11

Temperature requirements

To ensure continued safe and reliable equipment operation, install or position the rack in a well ventilated,

climate-controlled environment.

The operating temperature inside the rack is always higher than the room temperature and is dependent on

the configuration of equipment in the rack. Check the TMRA for each piece of equipment before installation.

CAUTION: To reduce the risk of damage to the equipment when installing third-party options:

• Do not permit optional equipment to impede airflow around the enclosure or to increase the

internal rack temperature beyond the maximum allowable limits.

• Do not exceed the manufacturer’s TMRA.

Power requirements

Installation of this equipment must comply with local and regional electrical regulations governing the

installation of IT equipment by licensed electricians. This equipment is designed to operate in installations

covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992 (code for Protection of

Electronic Computer/Data Processing Equipment). For electrical power ratings on options, refer to the

product rating label or the user documentation supplied with that option.

WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not

overload the AC supply branch circuit that provides power to the rack. Consult the electrical

authority having jurisdiction over wiring and installation requirements of your facility.

CAUTION: Protect the enclosure from power fluctuations and temporary interruptions with a

regulating UPS. This device protects the hardware from damage caused by power surges and

voltage spikes and keeps the enclosure in operation during a power failure.

Grounding requirements

This equipment must be grounded properly for proper operation and safety. In the United States, you must

install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250, as

well as any local and regional building codes.

In Canada, you must install the equipment in accordance with Canadian Standards Association, CSA

C22.1, Canadian Electrical Code.

In all other countries, you must install the equipment in accordance with any regional or national electrical

wiring codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7.

Furthermore, you must be sure that all power distribution devices used in the installation, such as branch

wiring and receptacles, are listed or certified grounding-type devices.

Because of the high ground-leakage currents associated with this equipment, HP recommends the use of a

PDU that is either permanently wired to the building’s branch circuit or includes a nondetachable cord that

is wired to an industrial-style plug. NEMA locking-style plugs or those complying with IEC 60309 are

considered suitable for this purpose. Using common power outlet strips to supply power to this equipment is

not recommended.

Component and LED identification 12

Component and LED identification

Enclosure front components

Item Description

1

Device bays*

2

Air intake slot (Do not block.)

3

Power supply bay 1

4

Power supply bay 2

5

Power supply bay 3

6

Power supply bay 4

7

Insight Display

8

Power supply bay 5

9

Power supply bay 6

10

Air intake slot (Do not block.)

*For more information, see "Device bay numbering (on page 14)."

Component and LED identification 13

Power supply bay numbering

Power supply LEDs

Power LED 1

(green)

Fault LED 2

(amber)

Condition

Off

Off No AC power to the power supply

On

Off Normal

Off

On Power supply failure

For power supply configuration information, see Installing a power supply (on page 29).

Component and LED identification 14

Device bay numbering

Each enclosure requires interconnects to provide network access for data transfer. Interconnects reside in

bays located on the rear of the enclosure. Be sure to review device bay numbering to determine which

external network connections on the interconnects are active.

IMPORTANT: When looking at the rear of the enclosure, front device bay numbering is reversed.

Full-height device bay numbering

Half-height device bay numbering

Component and LED identification 15

HP BladeSystem Insight Display components

Item Description Function

1

Insight Display screen Displays Main Menu error messages and instructions

2

Left arrow button Moves the menu or navigation bar selection left one position

3

Right arrow button Moves the menu or navigation bar selection right one position

4

OK button Accepts the highlighted selection and navigates to the selected

menu

5

Down arrow button Moves the menu selection down one position

6

Up arrow button Moves the menu selection up one position

Location Discovery Services

HP provides built-in location awareness in the new ProLiant servers, a capability that works hand-in-hand with

technology in the new HP Intelligent Series racks. Together these technologies provide the rack identification

number and precise U location of the servers. This information is communicated through SIM, ICPM, and HP

iPDUs.

For LDS software requirements, see the QuickSpecs on the HP website

(http://www.hp.com/go/rackandpower).

This feature is only available on HP BladeSystem c7000 Platinum Enclosures.

Component and LED identification 16

The following figure shows the location of the contacts on the c7000 enclosure that enable use of LDS.

Enclosure rear components

Item Description

1

Fan bay 1

2

Fan bay 2

3

Fan bay 3

4

Fan bay 4

5

Fan bay 5

6

Interconnect bay 2

7

Interconnect bay 4

8

Interconnect bay 6

9

Interconnect bay 8

Component and LED identification 17

Item Description

10

Onboard Administrator bay 2

11

Power supply exhaust vent (do not block)

12

Fan bay 10

13

Fan bay 9

14

Fan bay 8

15

Fan bay 7

16

Fan bay 6

17

AC power connectors

18

Onboard Administrator bay 1

19

Interconnect bay 7

20

Interconnect bay 5

21

Interconnect bay 3

22

Interconnect bay 1

Fan bay numbering

Component and LED identification 18

Fan LED

LED color Fan status

Solid green

The fan is working.

Solid amber

The fan has failed.

Flashing amber

See the Insight Display screen.

Onboard Administrator components

Item Description

1

Onboard Administrator bay 1

2

Onboard Administrator bay 2 (redundant, if used)

3

Enclosure link-up port

4

Enclosure link-down port

Component and LED identification 19

HP c7000 Onboard Administrator with KVM components

Item Name Description

1

Reset button —

2

OA/iLO management port Ethernet 100BaseT RJ45

connector, which

provides Ethernet access

to the Onboard

Administrator and the

iLO on each blade. Also

supports interconnect

modules with

management processors

configured to use the

enclosure management

network. Also supports

GbE.

3

UID LED Blue = UID on

4

Active Onboard

Administrator LED

Indicates which

Onboard Administrator

is active

5

Health LED Green = OK

Red = Critical error

6

USB USB 2.0 Type A

connector used for

connecting supported

USB devices such as DVD

drives, USB key drives, or

a keyboard or mouse for

enclosure KVM use. To

connect multiple devices,

a USB hub (not included)

is required.

Component and LED identification 20

Item Name Description

7

Serial connector Serial RS232 DB-9

connector with PC

standard pinout. Connect

a computer with a

null-modem serial cable

to the Onboard

Administrator command

line interface (CLI).

8

VGA VGA DB-15 connector

with PC standard pinout.

To access the KVM menu

or Onboard

Administrator CLI,

connect a VGA monitor

or rack KVM monitor for

enclosure KVM.

Interconnect bay numbering

To support network connections for specific signals, install the interconnect module into the appropriate bay.

Server blade signal Interconnect bay

number

Interconnect bay label

NICs 1, 2, 3, and 4

(embedded)

1, 2

Mezzanine 1

3, 4

Mezzanine 2

5, 6 and then 7, 8

Mezzanine 3

7, 8 and then 5, 6

For information on the location of LEDs and ports on individual interconnect modules, see the documentation

that ships with the interconnect module.

For more information, see "Mapping to interconnect ports (on page 48)."

La pagina sta caricando ...

HP c7000 Manuale utente

Questo manuale è adatto anche per

HP c7000 Manuale utente

in altre lingue

Documenti correlati

Altri documenti