Sparky SMA 1212CES Plus Manuale utente

www.sparky.eu

1 – 14

SANDER

Original instructions

31 – 46

PONCEUSE

Notice originale

110 – 126

ШЛИФОВАЛЬНАЯ МАШИНА

Оригинальная инструкция по эксплуатации

15 – 30

SCHLEIFER

Originalbetriebsanleitung

Оригінальна інструкція з експлуатації

127 – 142

ШЛІФУВАЛЬНА МАШИНА

94 – 109

SZLIFIERKA

Oryginalna instrukcja obsługi

78 – 93

REBARADORA

Manual original

47 – 61

SMERIGLIATRICE

Istruzioni originali

62 – 77

ESMERILADORA

Instrucciones de uso originales

Оригинална инструкция за използване

143 – 159

ШЛИФОВЪЧНА МАШИНА

1200 W

SM 1212CES Plus • SMA 1212CES Plus

6 March 2017

Manufacturer

SPARKY Power Tools GmbH

Leipziger Str. 20

10117 Berlin, GERMANY

Signature of authorized person

A. Ivanov

Technical director of SPARKY ELTOS AD

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, described under “Technical specications”, fulls all the relevant provisions of the

following directives and the harmonized standards: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Technical le is stored at SPARKY ELTOS AD, Kubrat Str. 9, 5500 Lovech, Bulgaria.

KONFORMITÄTSERKLÄRUNG

Hiermit versichern wir unsere persönliche Haftung, dass Produkt im Abschnitt “Technische Daten“ beschrieben“ allen einschlägigen

Bestimmungen folgender Richtlinien und entsprechender harmonisierten Standards entspricht: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Die technischen Unterlagen werden bei SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovech, Bulgarien, aufbewahrt.

DECLARATION DE CONFORMITE

Nous déclarons sous notre responsabilité que le produit décrit dans la rubrique “Données techniques” satisfait à l’ensemble des dispositions

pertinentes des présentes directives, respectivement aux normes harmonisées: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Le dossier technique est conservé par SPARKY ELTOS AD, 9, rue Kubrat, 5500 Lovech, Bulgarie.

DICHIARAZIONE DI CONFORMITÀ

Noi dichiariamo sotto la nostra personale responsabilità, che il prodotto, descritto nella sezione “Dati tecnici” è in conformità a tutte le disposizioni

pertinenti della presente direttive e norme armonizzate: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Il fascicolo tecnico viene custodito presso la SPARKY ELTOS AD, 5500 Lovech, via Kubrat n. 9, Bulgaria.

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que el producto, descrito en los “Datos técnicos”, está conforme con todas las disposiciones

aplicables de la presente directrices aplicables y las correspondientes normas armonizadas: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

El expediente técnico está archivado en SPARKY ELTOS AD, C/ Kubrat, 9, 5500 Lovech, Bulgaria.

DECLARAÇÃO DE CONFORMIDADE

Declaramos assumindo a nossa responsabilidade pessoal que el producto, descrito en los “Dados técnicos”, está conforme com todas as

disposições relevantes da presente directrizes aplicáveis e respectivos estandartes harmonizados: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

A documentação técnica guarda-se no SPARKY ELTOS AD, rua Kubrat 9, 5500, Lovech, Bulgária.

DEKLARACJA ZGODNOŚCI

Niniejszym deklarujemy naszą osobistą odpowiedzialnością, że produkt, przedstawiony w rozdziale „Dane techniczne“, pełnia wszystkie

odpowiednie postanowienia następujących dyrektyw i harmonizowanych standardów: 2006/42/WЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Teczka techniczna przechowywana jest w SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovetch, Bułgaria.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ

Мы заявляем со всей ответственностью, что продукт, описанный в разделе “Технические данные“, полностью соответствует всем

соответствующим требованиям действующих директив и гармонизированных стандартов: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Техническое досье хранится в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, Болгария.

ДЕКЛАРАЦІЯ ПРО ВІДПОВІДНІСТЬ

Ми заявляємо під свою власну відповідальність, що продукт, описаний у розділі “Teхнічні дані“ відповідає всім діючим вимогам директив і

гармонізованих стандартів: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Технічне досьє зберігається в СПАРКИ ЕЛТОС АД, ул. Кубрат № 9, 5500 Ловеч, Болгарія.

ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ

Ние декларираме на своя лична отговорност, че изделието, описано в раздел “Технически данни”, отговаря на всички приложими

изисквания на следните директиви и хармонизирани стандарти: 2006/42/ЕС,2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Техническото досие се съхранява в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, България.

BLACK PANTONE185

BА

A B

2015 1616 2114

45

1

10

6

14

20

15

25

23

21

16

17

18

12

8

9

11

13

2

3

22

26

7

24

19

BLACK PANTONE185

1

EN

Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured

under stringent SPARKY Quality Standards to meet superior performance criteria. You will nd your

new tool easy and safe to operate, and, with proper care, it will give you many years of dependable

service.

WARNING:

Carefully read through these Original Instructions before using your new SPARKY power tool.

Take special care to heed the Warnings. Your SPARKY power tool has many features that will

make your job faster and easier. Safety, performance, and dependability have been given top

priority in the development of this tool, making it easy to maintain and operate.

Do not dispose of electric tools together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly

recycling.

The plastic components are labelled for categorised recycling.

UNPACKING

Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is

missing. If you nd anything wrong, do not operate the tool until the parts have been replaced or the

fault has been rectied. Failure to do so could result in serious personal injury.

ASSEMBLY

The power tool is packed assembled except for the sandpaper.

Contents

Introduction ............................................................................................................................... 1

Technical specications ...........................................................................................................3

General power tool safety warnings ..........................................................................................4

Additional safety rules for sanders ............................................................................................5

Know your product ................................................................................................................ A/7

Operation .................................................................................................................................. 7

Maintenance ...........................................................................................................................13

Warranty ..................................................................................................................................14

SM 1212CES Plus ● SMА 1212CES Plus ● Original instructions

2

EN

SM 1212CES Plus ● SMА 1212CES Plus

DESCRIPTION OF SYMBOLS

The rating plate on your power tool may show symbols. These represent important information about

the product or instructions on its use.

Double insulated for additional protection.

Conforms to the relevant European Directives.

Conforms to the requirements of Customs Union regulations.

Spindle thread: M14.

Hoop-and-loop fastening.

Conforms to the requirements of Ukrainian standards.

Refer to Original Instructions.

YYYY-Www Production period, where the variable symbols are:

YYYY- year of manufacture,

ww - calendar week number.

SM, SMA Sander.

3

Original instructions

EN

The vibration emission level given in this information sheet has been measured in accordance with

a standardised test given in EN 60745 and may be used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool

is used for different applications, with different accessories or poorly maintained, the vibration emis-

sion may differ. This may signicantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the

tool is switched off or when it is running but not actually doing the job. This may signicantly reduce

the exposure level over the total working period.

Maintain the power tool and the accessories and keep your hands warm during operation to reduce

the harmful effect of vibrations.

Other applications such as cutting-off or wire brushing may have different vibration emission values.

Dust from material such as paint containing lead, some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory dis-

eases to the operator or bystanders.

Certain kinds of dust are classied as carcinogenic such as oak and beech dust especially in conjunc-

tion with additives for wood conditioning (chromate, wood preservative). Material containing asbestos

must only be treated by specialists.

▪ Where the use of a dust extraction device is possible it shall be used.

▪ The work place must be well ventilated.

▪ The use of a dust mask of lter class P2 is recommended.

Follow national requirements for the materials you want to work with.

Technical specications

Model SM 1212CES Plus SMA 1212CES Plus

Power input 1200 W 1200 W

Rated speed 240-1250 min

-1

240-1250 min

-1

Sanding head diameter 226 mm 248 mm

Sanding paper max. diameter 200 mm 225 mm

Dust extraction port diameter Ø35 mm Ø35 mm

Spindle thread M14 M14

Overall dimensions

Length 475 mm 486 mm

Width 230 mm 250 mm

Height 170 mm 170 mm

Weight (EPTA Procedure 01/2014) 3,2 kg 3,2 kg

Protection class (EN 60745-1) II II

NOISE AND VIBRATION INFORMATION

Measured values determined according to EN 60745.

Noise emission

A-weighted sound pressure level L

pA

90 dB(А) 90 dB(А)

Uncertainty К

pA

3 dB(A) 3 dB(A)

A-weighted sound power level L

wA

101 dB(А) 101 dB(А)

Uncertainty К

wA

3 dB(A) 3 dB(A)

Wear hearing protection!

Vibration emission *

Total vibration values (vector sum in the three axes) determined according to EN 60745:

Sanding

Vibration emission value a

h,DS

7,5 m/s

2

7,5 m/s

2

Uncertainty К

DS

1,5 m/s

2

1,5 m/s

2

* The vibration emission values are determined according to 6.2.7 EN 60745.

4

EN

SM 1212CES Plus ● SMА 1212CES Plus

General power tool

safety warnings

WARNING! Read all safety warn-

ings and all instructions. Failure to follow

the warnings and instructions may result in

electric shock, re and/or serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence

of ammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodied

plugs and matching outlets will reduce risk

of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, ra-

diators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric shock.

f) If operating a power tool in a damp lo-

cation is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the inu-

ence of drugs, alcohol or medication.

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will re-

duce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your nger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal in-

jury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpect-

ed situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, cloth-

ing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connec-

tion of dust extraction and collection fa-

cilities, ensure these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or stor-

5

Original instructions

EN

ing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s op-

eration. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for op-

erations different from those intended could

result in a hazardous situation.

5) Service

a) Have your power tool serviced by a

qualied repair person using only iden-

tical replacement parts. This will ensure

that the safety of the power tool is main-

tained.

Additional safety

rules for sanders

Safety Warnings Common for Sanding:

a) This power tool is intended to function

as a sander. Read all safety warnings,

instructions, illustrations and speci-

cations provided with this power tool.

Failure to follow all instructions listed below

may result in electric shock, re and/or seri-

ous injury.

b) Operations such as grinding or cutting-

off are not recommended to be per-

formed with this power tool.

Operations

for which the power tool was not designed

may create a hazard and cause personal

injury.

c) Do not use accessories which are

not specically designed and recom-

mended by the tool manufacturer. Just

because the accessory can be attached to

your power tool, it does not assure safe op-

eration.

▪ Never mount circular blades or grinding

wheels for angle grinders.

▪ Use only accessories appropriate for

the processed material and the rotation

speed.

d) The rated speed of the accessory must

be at least equal to the maximum speed

marked on the power tool. Accessories

running faster than their rated speed can

break and y apart.

e) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

correctly sized accessories cannot be ad-

equately guarded or controlled.

f) Threaded mounting of accessories

must match the grinder spindle thread.

For accessories mounted by anges,

the arbour hole of the accessory must

t the locating diameter of the ange.

Accessories that do not match the mount-

ing hardware of the power tool will run out

of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Be-

fore each use inspect the accessory

such as backing pad for cracks, tear

or excess wear, wire brush for loose or

cracked wires. If power tool or acces-

sory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away

from the plane of the rotating accessory

and run the power tool at maximum no-

load speed for one minute. Damaged ac-

cessories will normally break apart during

this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping ying debris

generated by various operations. The dust

mask or respirator must be capable of l-

trating particles generated by your opera-

tion. Prolonged exposure to high intensity

noise may cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

6

EN

SM 1212CES Plus ● SMА 1212CES Plus

work area must wear personal protec-

tive equipment. Fragments of workpiece

or of a broken accessory may y away and

cause injury beyond immediate area of op-

eration.

▪ Use clamps or a vice to secure your

work whenever possible.

▪ Do not apply side pressure to stop the

pad rotation after switching the machine

off.

▪ Guide the machine towards the proc-

essed material only if the machine is

switched on.

j) Position the cord clear of the spinning

accessory. If you lose control, the cord

may be cut or snagged and your hand or

arm may be pulled into the spinning acces-

sory.

k) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the sur-

face and pull the power tool out of your con-

trol.

l) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your cloth-

ing, pulling the accessory into your body.

m) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust

inside the housing and excessive accumu-

lation of powdered metal may cause electri-

cal hazards.

n) Do not operate the power tool near am-

mable materials. Sparks could ignite these

materials.

o) Do not use accessories that require

liquid coolants. Using water or other liq-

uid coolants may result in electrocution or

shock.

▪ This power tool is designed for dry

sanding only.

▪ The tool must be used only for its pre-

scribed purpose. Any use other use

than those mentioned in this Instruction

will be considered a case of misuse. The

user and not the manufacturer shall be li-

able for any damage or injury resulting from

such cases of misuse.

▪ The manufacturer shall not be liable for

any changes made to the tool nor for any

damage resulting from such changes.

▪ When operating in dusty environment,

the ventilation slots must be kept clean.

If it should become necessary to clear

dust, rst disconnect the tool from the

mains supply (use non metallic objects

to clean the dust) and avoid damaging

internal parts. The power tool will over-

heat under deteriorated cooling due to the

clogged with dust ventilation slots.

▪ Power tools must not be used outdoors

in rainy weather, or in moist environ-

ment (after rain) or in close vicinity with

easily ammable liquids and gases. The

working place should be well lit.

Further safety instructions for all opera-

tions

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush

or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the ac-

cessory’s rotation at the point of the binding.

Kickback is the result of power tool misuse and/

or incorrect operating procedures or conditions

and can be avoided by taking proper precau-

tions as given below.

a) Maintain a rm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. Al-

ways use auxiliary handle, if provided,

for maximum control over kickback or

torque reaction during start-up. The

operator can control torque reactions or

kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over

your hand.

c) Do not position your body in the area

where power tool will move if kickback

occurs. Kickback will propel the tool in di-

rection opposite to the pad movement at

the point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to

snag the rotating accessory and cause loss

of control or kickback.

е) Do not attach a saw chain woodcarving

blade or toothed saw blade.

Such blades

create frequent kickback and loss of con-

trol.

Safety Warnings Specic for Sanding

Operations:

a) Do not use excessively oversized sand-

7

Original instructions

EN

ing disc paper. Follow manufacturer’s

recommendations, when selecting

sanding paper. Larger sanding paper ex-

tending beyond the sanding pad presents

a laceration hazard and may cause snag-

ging, tearing of the disc or kickback.

Know your product

Before using the power tool, familiarize your-

self with all the operating features and safety

requirements.

Use the tool and accessories only for the ap-

plications intended. All other applications are

expressly ruled out.

POWER TOOL BASIC PARTS FOR ALL

INTENDED APPLICATIONS

1. Bearing bed

2. Front handle

3. Spindle lock button

4. Driving machine

5. ON/OFF switch

6. Clamp

7. Lock screw

8. Spindle

9. Spring

10. Dust extraction port

11. Guard

12. Brush ring

13. Seeger circlip

14. Support ange

15. Support disc

16. Tightening nut

17. Flexible pad

18. Sandpaper

19. Electronic speed regulator

20. Support ange

21. Lightweight diamond disc *

22. Support bush

23. M14 exible backing pad *

24. Vacuum cleaner hose *

25. Sanding pad for dry ne sanding *

26. Pin spanner

* The additional accessories shown in the illus-

trations or described in the text are not included

in the delivery.

ACCESSORIES TO BE USED WITH

THIS POWER TOOL

Sandpaper up to Ø200 mm for

SM 1212CES Plus;

Sandpaper up to Ø225 mm for

SMA 1212CES Plus;

Abrasive net discs Ø200 mm for

SM 1212CES Plus;

Abrasive net discs Ø225 mm for

SMА 1212CES Plus

Diamond discs with various grit max. Ø7”

(max 0,5 kg);

Sanding pads for dry ne sanding max. Ø7”

with hook-and-loop fastening;

M14 exible backing pad with hook-and-loop

fastening.

Operation

These power tools are supplied from single-

phase alternating current mains only. They are

double insulated according to EN 60745-1,

IEC 60745-1 and can be connected to grounded

or not grounded sockets. This power tool is radio

suppressed in compliance with EMC Directive.

The basic use of this power tool is for sand-

ing plaster coated ceilings and walls, for sand-

ing smoothed drywalls and for removing paint,

wallpaper and adhesive remnants by means of

sandpaper.

When using an appropriate tool the machine can

be used for sanding stone and concrete walls.

This power toll is not designed for CUTTING!

WARNING: Using this power tool with

accessories differing from the described here-

with may cause accidents during operation.

The possibility to connect an operating tool

does not mean the machine is designed to be

used with it.

Using this power tool with accessories differ-

ing from the described herewith and all risks

for your health resulting from such use are en-

tirely on YOUR OWN RESPONSIBILITY!

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corre-

sponds to the value indicated on the name

plate with technical data of the tool.

▪ Make sure that the cord and the plug are in

order. If the replacement of the supply cord is

necessary, this has to be done by the manu-

facturer or his agent in order to avoid a safety

hazard.

8

EN

SM 1212CES Plus ● SMА 1212CES Plus

WARNING: Always switch off and un-

plug the power tool prior to any adjustment,

servicing or maintenance.

▪ In case the work area is remote from the pow-

er source, use as short as practicable exten-

sion cord with proper cross-section.

▪ Check that the auxiliary handle is properly

mounted and reliably tightened.

PREPARATION FOR OPERATION

DUST EXTRACTION

WARNING: It is obligatory to connect

the sander to a M-class vacuum cleaner prior

to operation.

Using dust bags or lters inappropriate to col-

lect the dust separated during dry sanding will

increase the dust particles in the air. Over a pro-

longed period the high dust concentration in the

air may damage operator’s respiratory system.

CONNECTING TO A VACUUM CLEAN-

ER

Insert a special dust bag for collecting the dust

separated during dry sanding into the vacuum

cleaner according to the instructions supplied

with the vacuum cleaner.

Pass the hose through the clamp (6).

Connect the hose (24) of the vacuum cleaner to

the dust extraction port (10) positioned on the

guard (11).

We recommend using this power tool with

SPARKY vacuum cleaners to achieve optimum

results in collecting the dust generated during

operation.

USING AUXILIARY ACCESSORIES

The power tool is delivered with the clamp (6)

mounted to facilitate you.

This accessory is designed for additional fas-

tening of the vacuum cleaner hose to the power

tool.

The clamp (6) is mounted to the driving machine

(4).

Fasten the vacuum cleaner hose to the clamp (6).

As the clamp (6) is intended for a certain type of

hose in some cases the hose may move in the

clamp (24), in other cases it is rmly fastened.

This feature does not affect the power tool us-

age in any way.

SELECTING THE ACCESSORIES AND

PREPARATION FOR OPERATION

The selection of accessory depends on the in-

tended operation. Generally the permitted op-

erations with this power tool are the following:

- Sanding with sandpaper (18) or abrasive net;

- Cleaning with diamond disc (21);

- Fine sanding with sanding pads for dry ne

sanding max. Ø7” with hook-and-loop fasten-

ing.

Familiarise yourself with the instructions for

preparation for work with the corresponding ac-

cessory. Perform accurately the described pro-

cedures for mounting, replacement and remov-

ing the corresponding accessories.

SWITCHING ON - SWITCHING OFF

The sander is secured against unintentional

switching on.

Switching on: Select the necessary speed by

rotating the electronic regulator (19). Move the

ON/OFF switch (5) forward.

Switching off: Move the ON/OFF switch (5)

backward.

ELECTRONIC SPEED PRE-SELECTION

The rotation speed can be varied smoothly by

turning the electronic regulator (19), positioned

on the rear of the sander.

The speed adjustment range varies from n =

240 min

-1

to 1250 min

-1

according to the table

below:

Regulator position Speed, min

-1

A 240

B 400

C 570

D 740

E 910

F 1080

G 1250

The recommended regulator positions for the

different areas of applications are specied in

the table below:

9

Original instructions

EN

Area of application Regulator

position

1. Sanding plaster coated surfaces

with sandpaper E - G

2. Sanding wood and removing lacquer

and dye coatings D - G

3. Sanding metal with sandpaper E - G

4. Rough cleaning, metal or

stone sanding G

The sander is equipped with full-wave tachocon-

stant electronics for:

- Soft start and restriction of the starting cur-

rent;

- Speed pre-selection and control and main-

taining constant rpm upon overloading;

- Brief overload protection (upon jamming the

wheel). To resume operation release the ON/

OFF switch and then press it again.

- Continuous overload protection (the thermal

protection switches the machine off to protect

the motor from inadmissible overheating). Upon

actuating the thermal protection the machine

becomes disabled. Тo resume operation release

the ON/OFF switch and then press it again.

- Non-self starting safety (NVR) after restoring

the mains supply. To resume operation release

the ON/OFF switch and then press it again.

MOUNTING THE ACCESSORIES

When mounting the sanding accessories x the

sander spindle (1) by pressing the lock button

(3) positioned on the gear box.

WARNING: Never press the button

(3) while the spindle (8) is still rotating!

SANDING WITH SANDPAPER

The selection of sandpaper depends on the de-

sired surface quality. For rough operations use

sandpaper with larger grit size, and for ne and

nishing operations use sandpaper with smaller

grit size to achieve surface smoothness.

We recommend using original SPARKY acces-

sories specially designed for achieving optimum

results.

Use only hook-and-loop sanding sheets.

Do not use sanding discs with diameter exceed-

ing the maximum permitted for the power tool.

Refer to power tool specications.

MOUNTING THE ACCESSORIES FOR

SANDING WITH SANDPAPER

The precise and accurate performance of the

below described procedures guarantees the

reliable and safe operation with the power tool.

All instructions are important and result from our

huge experience gained during design and op-

eration of power tools for the described use.

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Clean the threaded and face surfaces of

the spindle (8) using soft cloth and brush.

4. Take out the sanding set from the pack-

ing.

5. Clean the ange (14) face surface and

arbour and the support disc (27) face surfaces

using a soft cloth and brush. The support ange

(14) is the thinner ange.

6. Place the support ange (14) onto the

spindle (8) observing the orientation - its at

face should stick to the spindle (8) ange. In-

correctly chosen ange (14) will deteriorate dust

extraction.

7. Ensure there is no dirt or foreign body be-

tween the spindle (8) face and the ange (14)

face which may hamper their contact. The pres-

ence of foreign bodies and disturbed face con-

tact are prerequisites for inexact movement of

the operating tool and increased vibration caus-

ing unsatisfactory quality of the processed sur-

face.

8. Mount the support disc (15) on the ange

(14) and ensure there are no foreign bodies be-

tween their faces.

9. Fasten the tightening nut (16) to x the

support disc (15) to the spindle (8) rmly. It is

obligatory to observe the tightening nut (16) ori-

entation as shown on Fig. A. Otherwise tighten-

ing the support disc (15) will not be possible.

10. Press the spindle lock button (3) and ro-

tate the support disc (15) clockwise until the but-

ton sinks and locks the spindle (8) movement.

11. Fasten the tightening nut (16) reliably us-

ing the pin spanner (26) supplied with the ma-

chine.

12. Release the spindle lock button (3) and

ensure that the button is back in its initial po-

sition and does not lock the spindle (8) move-

ment. If necessary rotate the spindle (8) by hand

to release the button (3) so it can return in its

initial position.

10

EN

SM 1212CES Plus ● SMА 1212CES Plus

13. Remove the pin spanner (26).

14. Mount the exible pad (17) onto the sup-

port disc (15). Ensure the coaxiality between the

openings of the support disc (15) and the ex-

ible pad (17) for better dust extraction. Proper

dust extraction is a prerequisite for high quality

of the processed surface.

MOUNTING THE SANDPAPER

The machine is delivered assembled. All you

have to do is mount the selected sandpaper

and check if the tightening nut (16) is fastened

rmly.

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Fasten the tightening nut (16) rmly using

the pin spanner (26) supplied with the machine.

4. Mount the selected sandpaper disc trying

to ensure its coaxiality toward the exible pad

and the support disc.

5. Ensure the coaxiality between the open-

ings of sandpaper and the exible pad (17) for

better dust extraction. Proper dust extraction is

a prerequisite for high quality of the processed

surface.

6. Press the sandpaper (18) to the exible

pad (17) to ensure maximum cohesion of the

hook-and-loop surfaces.

7. Turn the machine with the sandpaper fac-

ing downward.

8. Plug in the power tool.

9. Select position G of the electronic regula-

tor (19). Slide the ON/OFF switch slider (5) for-

ward to start the machine.

10. Let the machine operate at no load for ap-

proximately one minute not allowing the operat-

ing tool to contact any surface.

11. At the event of increased vibrations or

other symptoms not typical for operation, stop

the machine immediately and search for the

reason. If you can not detect the reason your-

self - contact the nearest authorised SPARKY

service centre. Operating with a faulty machine

may cause an accident!

12. If no trouble is detected then you can start

operation.

REPLACING THE SANDPAPER

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Remove the clogged sandpaper (18) by

tearing it from the exible pad (17).

4. Follow steps 4 - 12 described in section

„Mounting the sandpaper”.

REMOVING THE ACCESSORIES FOR

SANDING WITH SANDPAPER

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Remove the sandpaper (18).

4. Remove the exible pad (17) by tearing it

from the support disc (15).

5. Press the spindle lock button (3) and rotate

by hand the operating accessory clockwise until

the button sinks and locks the spindle. Remove

the tightening nut (16) using the pin spanner

(26). After removing the nut ensure that the lock

button (3) has returned in its initial position and

does not lock the spindle (8) movement. In case

the button (3) still locks the spindle (8) rotate the

spindle by hand until the lock button has been

released and returned in its initial position.

6. Remove the support disc (15) and the sup-

port ange (14).

SANDING WITH ABRASIVE NET

Operation with abrasive net is entirely analogi-

cal to operating with sandpaper.

Familiarise yourself with the corresponding

information for using sandpaper in the corre-

sponding sections and perform the described

procedures.

OPERATING WITH DIAMOND DISC

The choice of the diamond disc (21) depends on

the material you intend to process, the surface

quality you intend to achieve, etc. The maximum

diamond disc diameter to use with this machine

is 7” (~178 mm). The diamond disc max. weight

should not exceed 0.5 kg. Diamond disc bore

shall be Ø22.23 mm. The use of discs with bore

differing from the specied here is not admitted.

MOUNTING THE DIAMOND DISC

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

11

Original instructions

EN

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. If you have already used the power tool

with another accessory - remove it following the

steps described in the corresponding section for

this accessory.

4. Clean the threaded and face surfaces of

the spindle (8) using a soft cloth.

5. Take the ange (20) for operation with a

diamond disc and place it on the face of the

spindle (8). Please note that ange (20) for

operation with a diamond disc is different from

ange (14) for operation with sandpaper. The

visual difference is in their thickness - the ange

for operating with a diamond disc is thicker. The

support ange (20) is thicker than ange (14). If

the ange is selected improperly operation will

be impossible as the spindle will project consid-

erably above the diamond disc surface.

6. Ensure there is no dirt or foreign body be-

tween the spindle (8) face and the ange (20)

face which may hamper their contact. The pres-

ence of foreign bodies and disturbed face con-

tact are prerequisites for inexact movement of

the operating tool and increased vibration caus-

ing unsatisfactory quality of the processed sur-

face.

7. Mount the diamond disc (21) so that its

bore enters the ange (20) step.

8. Fasten the nut (16) in order to x rmly the

diamond disc (21) to the spindle (8). It is obliga-

tory to observe the orientation of the xing nut

(16) as shown on Fig. B. Otherwise the nut (16)

will not x the diamond disc (21) reliably.

9. Press the spindle lock button (3) and ro-

tate the spindle (8) clockwise until the button

sinks and locks the spindle (8) movement.

10. Tighten rmly the nut (16) using the pin

spanner (26) supplied with the machine.

11. Release the spindle lock button (3). En-

sure that the button (3) has returned in its ini-

tial position and does not lock the spindle (8)

movement. In case the button (3) still locks the

spindle (8), rotate the spindle (8) or the diamond

disc (21) by hand until the button (3) has been

released and returned in its initial position.

12. Remove the pin spanner (26).

13. Turn the machine with the diamond disc

facing downward.

14. Plug the power tool.

15. Slide the ON/OFF switch (5) forward to

switch on the machine.

16. Let the machine operate at no load for

approximately one minute not allowing the dia-

mond disc (21) to contact any surface.

17. At the event of increased vibrations or

other symptoms not typical for operation, stop

the machine immediately and search for the

reason. If you can not detect the reason your-

self - contact the nearest authorised SPARKY

service centre. Operating with a faulty machine

may cause an accident!

18. If no trouble is detected then you can start

operation.

REPLACING THE DIAMOND DISC

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Press the spindle lock button (3) and ro-

tate the diamond disc (21) by hand clockwise

until the button sinks and locks the spindle (8)

movement. Remove the tightening nut (16) us-

ing the pin spanner (26). After removing the

nut ensure that the button (3) has returned in

its initial position and does not lock the spindle

(8) movement. In case the button (3) still locks

the spindle (25) rotate the spindle by hand until

the button has been released and returned in its

initial position.

4. Remove the diamond disc (21) and ange

(20).

5. Clean the accessories for operation with

the diamond disc and store them for future use.

6. Follow steps 4 - 18 from section „Mounting

the diamond disc”.

REMOVING THE ACCESSORIES FOR

OPERATION WITH DIAMOND DISC

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Follow steps 3 - 5 from section „Replacing

the diamond disc”.

OPERATING WITH SANDING PADS

FOR FINE SANDING

Sanding pads (25) for dry ne sanding and

hook-and-loop fastening and a exible backing

pad are used for this purpose.

The selection of a pad for ne sanding (25) de-

pends on the desired surface quality. Usually to

12

EN

SM 1212CES Plus ● SMА 1212CES Plus

achieve the nal surface appearance several

pads with different grit are used starting with a

larger grit pad and passing consecutively to the

smallest grid pad for nishing.

The sanding pad (25) diameter must be equal to

the exible backing pad diameter.

Check the condition of the exible pad (23)

hook-and-loop fastening regularly. Hook-and-

loop fastening with injured and worn-out hooks

is a prerequisite for poor sanding pad fastening

and hence - a probability for an accident. Do not

operate exible pads with damaged hook-and-

loop system.

MOUNTING THE SANDING PAD

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. If you have already used the power tool

with another accessory - remove it following the

steps described in the corresponding section for

this accessory.

4. Clean the threaded and face surfaces of

the spindle (8) using a soft cloth.

5. Place the support bush (22) on the spindle

(8) front surface.

6. Ensure there is no dirt or foreign body

between the spindle (8) face and the bush (22)

face which may hamper their contact. The pres-

ence of foreign bodies and disturbed face con-

tact are prerequisites for inexact movement of

the operating tool and increased vibration caus-

ing unsatisfactory quality of the processed sur-

face.

7. Screw the exible backing pad (23) onto

the spindle (8) М14 thread.

8. Press the spindle lock button (3) and ro-

tate the exible backing pad (23) clockwise until

the button sinks and locks the spindle (8) move-

ment.

9. Tighten the exible backing pad (23) by

hand rotating it clockwise.

10. Release the spindle lock button (3). En-

sure that the button (3) has returned in its ini-

tial position and does not lock the spindle (8)

movement. In case the button (3) still locks the

spindle (8), rotate the spindle (8) or the sanding

pad (23) by hand until the button (3) has been

released and returned in its initial position.

11. Mount the selected sanding pad (25) try-

ing to ensure its coaxiality toward the exible

backing pad (23). Coaxiality is a prerequisite for

lack of vibrations and hence - better quality of

the processed surface.

12. Turn the machine with the sanding pad

(25) facing downward.

13. Plug the power tool.

14. Slide the ON/OFF switch slider (5) forward

to switch on the machine.

15. Let the machine operate at no load for ap-

proximately one minute not allowing the sanding

pad (25) to contact any surface.

16. At the event of increased vibrations or

other symptoms not typical for operation, stop

the machine immediately and search for the

reason. If you can not detect the reason your-

self - contact the nearest authorised SPARKY

service centre. Operating with a faulty machine

may cause an accident!

17. If no trouble is detected then you can start

operation.

REPLACING THE SANDING PAD

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Remove the used sanding pad (25).

4. Follow steps 11 - 17 from section „Mount-

ing the sanding pad”.

REMOVING THE ACCESSORIES FOR

OPERATION WITH SANDING PADS

1. Ensure that the power tool is unplugged.

2. Turn the machine in a way ensuring ac-

cess to the operating tool. We recommend xing

the machine in stationary position. Thus it would

be possible to use both hands for convenient

and safe assembly.

3. Press the spindle lock button (3) and ro-

tate the sanding set by hand clockwise until the

button sinks and locks the spindle movement.

Remove the exible backing pad (23) rotating it

anti-clockwise. After removing the exible back-

ing pad (23) release the lock button (3) and en-

sure that it has returned in its initial position and

does not lock the spindle (8) movement. In case

the button (3) still locks the spindle (25) rotate

the spindle by hand until the button has been

released and returned in its initial position.

4. Remove the exible backing pad (23) and

the bush (22).

5. Clean the accessories for operation with

ne sanding pads and store them for future

use.

13

Original instructions

EN

SANDING WALLS AND CEILINGS WITH

SANDPAPER OR ABRASIVE NET

The brush ring (12) is situated on the guard (11)

perimeter. The brush ring features two func-

tions:

- It is the brush ring that comes into contact with

the processed surface rst. As a result the guard

becomes parallel to the surface even before the

operating tool contacts it. This ensures uniform

contact between the tool and the surface.

- The brush ring retains the dust generated

during operation which is subject to extraction

by the dust extraction system and the vacuum

cleaner.

In case the brush ring (12) is damaged, de-

formed or worn out it can not perform the func-

tions it is designed for and shall be replaced im-

mediately. You can purchase a brush ring (12) in

any SPARKY service centre.

Excessive pressure may result in spiral pattern

of scratches, concaves and roughness of the

processed surface. Moreover excessive pres-

sure will overload machine transmission and

probably cause damage of the exible shaft.

The driving machine must be running constantly

while the sanding head is in contact with the

processed surface.

Move the sanding head with uniform speed over

the entire area of the processed surface. Exces-

sive slow motion and motion intermission of the

sanding head will cause uneven processing of

the surface, tool digging and presence of con-

caves and bumps.

SURFACE PROCESSING WITH DIA-

MOND DISC

The diamond disc is most often used for clean-

ing concrete or stone surfaces and wall revet-

ment (footing).

Apply only as much pressure as is required to

keep the diamond disc (21) in contact with the

processed surface.

Do not apply excessive pressure. Excessive

pressure does not increase efciency. It is a

prerequisite for the power tool fault.

SURFACE PROCESSING WITH SAND-

ING PADS

The sanding pads for dry sanding (25) are most

often used to achieve a specic surface appear-

ance (cleaning, renovation, and gloss) of wall

revetment made of decorative stone slabs (mar-

ble, granite, limestone, etc.).

Apply only as much pressure as it is required

to keep the sanding pad (25) in contact with

the processed surface. Do not apply excessive

pressure. Excessive pressure does not increase

efciency. It is a prerequisite for the power tool

fault. Excessive pressure may damage the proc-

essed surface.

RECOMMENDATIONS

When sanding do not apply pressure to the

processed surface by rearing down on the ma-

chine but move the machine smoothly.

Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

BRUSH REPLACEMENT

This power tool is equipped with auto-stop

brushes. When the carbon brushes are worn

out, the machine switches itself off. In this case

both brushes must be replaced simultaneously

with genuine brushes at SPARKY service centre

for warranty and post-warranty service.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they

are properly tightened. Should any of the screws

be loose, retighten it immediately to avoid haz-

ards.

If the replacement of the supply cord is neces-

sary, this has to be done by the manufacturer or

his agent in order to avoid a safety hazard.

CLEANING

For safe operation always keep the machine

and its ventilation slots clean.

Regularly check to see if any dust or foreign mat-

ter has entered the ventilation slots and the grills

around the switches. Use a soft brush and/or air

jet to remove any accumulated dust. Wear safety

glasses to protect your eyes whilst cleaning.

Exterior plastic parts may be cleaned with a

damp cloth and mild detergent if necessary.

14

EN

SM 1212CES Plus ● SMА 1212CES Plus

WARNING: Never use alcohol, petrol

or other cleaning agent. Never use caustic

agents to clean plastic parts.

WARNING: Water must never come

into contact with the tool.

IMPORTANT! To assure product safety and re-

liability, repairs, maintenance and adjustment

(including brush inspection and replacement)

should be performed by certied service centres

or other qualied service organisations, always

using genuine replacement parts.

Warranty

The guarantee period for SPARKY power tools

is determined in the guarantee card.

Faults due to normal wear, overloading or im-

proper handling will be excluded from the guar-

antee.

Faults due to defective materials implemented

as well as defects in workmanship will be cor-

rected free of charge through replacement or

repair.

The complaints for defective SPARKY power

tools will be recognized if the machine is sent

back to the dealer or is presented to the author-

ised warranty service centre undismantled, in its

initial condition.

Notes

Carefully read the entire Instruction Manual be-

fore using this product.

The manufacturer reserves the right to make

changes and improvements to the products and

to alter specications without prior notice.

Specications may differ from country to coun-

try.

15

DE

Originalbetriebsanleitung

Inhaltsverzeichnis

Einführung ...............................................................................................................................15

Technische Daten ....................................................................................................................17

Allgemeine Sicherheitshinweise für Elektrowerkzeuge ............................................................18

Sicherheitshinweise für die Arbeiten mit Schleifern .................................................................19

Elemente des Elektrowerkzeugs .......................................................................................... A/21

Betriebshinweise ......................................................................................................................22

Wartung ...................................................................................................................................29

Garantie .................................................................................................................................. 30

Einführung

Das von Ihnen erworbene Elektrowerkzeug wird Ihre Erwartungen übersteigen. Es ist gemäß den ho-

hen Qualitätsstandards von SPARKY hergestellt, die den strengen Anforderungen des Verbrauchers

entsprechen. Einfach in der Bedienung und ungefährlich bei richtiger Handhabung, wird dieses Gerät

bei bestimmungsgemäßem Gebrauch Ihnen lange Jahre zuverlässig dienen.

WARNUNG!

Lesen Sie die ganze Originalbetriebsanleitung aufmerksam durch, bevor Sie das neu erworbene

SPARKY – Elektrowerkzeug in Betrieb nehmen. Beachten Sie besonders die Texte, die mit

dem Wört „Warnung“ beginnen. Ihr SPARKY - Elektrowerkzeug besitzt viele Eigenschaften,

die Ihre Arbeit erleichtern werden. Bei der Entwicklung dieses Elektrowerkzeuges ist höchste

Aufmerksamkeit der Sicherheit, den Betriebseigenschaften und der Zuverlässigkeit gewidmet

worden, die es einfach zur Wartung und Bedienung machen.

Keine elektrischen Geräte zusammen mit dem Hausmüll wegwerfen!

Die Abfälle von elektrischen Erzeugnissen sollen nicht zusammen mit dem Hausmüll

gesammelt werden. Für eine umweltgerechte Entsorgung geben Sie Ihren alten / defekten

Elektrogeräte bitte in der nächsten kommunalen Sammelstelle ab.

UMWELTSCHUTZ

Angesichts des Umweltschutzes sollen das Elektrowerkzeug, die Zubehörteile und die

Verpackung einer geeigneten Wiederverwertung zugeführt werden.

Zum sortenreinen Recycling sind die Teile, hergestellt aus Kunststoffen, entsprechend

gekennzeichnet.

AUSPACKEN

Überprüfen Sie unmittelbar nach dem Auspacken ob sämtliche Bestandteile und das beschriebene

Zubehör mitgeliefert wurden. Sollte dies nicht der Fall sein, wenden Sie sich bitte umgehend an Ihren

Fachhändler bei dem das Elektrowerkzeug gekauft wurde. Dies trifft auch dann zu, wenn Sie den

Eindruck haben mit dem Gerät ist etwas nicht in Ordnung. Eine Nichtbeachtung dieser Empfehlung

kann zu schweren Unfällen führen.

ZUSAMMENBAU

Der Schleifer wird verpackt und vollständig montiert, mit Ausnahme des Schleifblattes, geliefert.

16

DE

SM 1212CES Plus ● SMА 1212CES Plus

BEDEUTUNG DER SYMBOLE

Auf dem Typenschild des Elektrowerkzeuges sind spezielle Symbole dargestellt. Sie stellen wichtige

Information über das Produkt oder Instruktionen für seine Nutzung dar.

Doppelte Isolierung für zusätzlichen Schutz.

Entspricht den einschlägigen Europäischen Richtlinien.

Entspricht den Anforderungen der Zollunion-Regelungen.

Spindelgewinde: M14

Klettverschluss.

Entspricht den Anforderungen der ukrainischen normativen Dokumenten.

Lesen Sie die Originalbetriebsanleitung.

YYYY-Www Zeitabschnitt der Produktion, wobei die variablen Symbole sind:

YYYY - Kalenderjahr der Produktion,

ww - laufende Kalenderwoche.

SM, SMA Schleifer.

17

DE

Originalbetriebsanleitung

Der in diesen Anweisungen angegebene Schwingungspegel ist entsprechend einem in EN 60745

genormten Messverfahren gemessen worden und kann für den Vergleich von Elektrowerkzeugen

miteinander verwendet werden. Er eignet sich auch für eine vorläuge Einschätzung der Schwin-

gungsbelastung.

Der angegebene Schwingungspegel repräsentiert die hauptsächlichen Anwendungen des Elektro-

werkzeugs. Wenn allerdings das Elektrowerkzeug für andere Anwendungen, mit abweichenden Ein-

satzwerkzeugen oder ungenügender Wartung eingesetzt wird, kann der Schwingungspegel abwei-

chen. Dies kann die Schwingungsbelastung über den gesamten Arbeitszeitraum deutlich erhöhen.

Für eine genaue Abschätzung der Schwingungsbelastung sollten auch die Zeiten berücksichtigt wer-

den, in denen das Gerät abgeschaltet ist oder zwar läuft, aber nicht tatsächlich im Einsatz ist. Dies

kann die Schwingungsbelastung über den gesamten Arbeitszeitraum deutlich reduzieren.

Pegen Sie das Gerät und die Einsatzwerkzeuge mit Sorgfalt. Halten Sie Ihre Hände warm während

der Arbeit - dies wird die schädliche Einwirkung erhöhter Schwingungen reduzieren.

Bei anderen Arbeiten, z.B. Schleifen mit Abrasivscheiben oder Reinigung mit Drahtbürste können die

Schwingungsemissionen auch andere Werte haben.

Stäube von Materialien wie bleihaltigem Anstrich, einigen Holzarten, Mineralien und Metall können

gesundheitsschädlich sein. Berühren oder Einatmen der Stäube können allergische Reaktionen und/

oder Atemwegserkrankungen des Benutzers oder in der Nähe bendlicher Personen hervorrufen.

Bestimmte Stäube wie Eichen- oder Buchenstaub gelten als krebserzeugend, besonders in Verbin-

dung mit Zusatzstoffen zur Holzbehandlung (Chromat, Holzschutzmittel). Asbesthaltiges Material darf

nur von Fachleuten bearbeitet werden.

▪ Benutzen Sie möglichst eine Staubabsaugung.

▪ Sorgen Sie für gute Belüftung des Arbeitsplatzes.

▪ Es wird empfohlen, eine Atemschutzmaske mit Filterklasse P2 zu tragen.

Beachten Sie in Ihrem Land gültige Vorschriften für die zu bearbeitenden Materialien.

Technische Daten

Modell SM 1212CES Plus SMA 1212CES Plus

Leistungsaufnahme 1200 W 1200 W

Bemessungsdrehzahl 240-1250 min

-1

240-1250 min

-1

Durchmesser des Schleifkopfes 226 mm 248 mm

Max. Durchmesser des Schleifblattes 200 mm 225 mm

Durchmesser des Absaugstutzens Ø35 mm Ø35 mm

Spindelanschlussgewinde M14 M14

Abmessungen:

Länge 475 mm 486 mm

Breite 230 mm 250 mm

Höhe 170 mm 170 mm

Gewicht (ЕРТА Prozedur 01/2014) 3,2 kg 3,2 kg

Schutzklasse (EN 60745-1) II II

GERÄUSCH-/VIBRATIONSINFORMATION

Messwerte ermittelt entsprechend EN 60745.

Geräuschemissionswerte

Der A-bewertete Schalldruckpegel L

pA

90 dB(А) 90 dB(А)

Messunsicherheit К

pA

3 dB(A) 3 dB(A)

Der A-bewertete Schalleistungspegel L

wA

101 dB(А) 101 dB(А)

Messunsicherheit К

wA

3 dB(A) 3 dB(A)

Gehörschutz tragen!

Schwingungsemissionswerte *

Schwingungsgesamtwerte (Vektorsumme dreier Richtungen) ermittelt entsprechend EN 60745:

Sandpapierschleifen

Schwingungsemissionswert a

h,DS

7,5 m/s

2

7,5 m/s

2

Messunsicherheit К

DS

1,5 m/s

2

1,5 m/s

2

* Vibrationen ermittelt nach Pkt. 6.2.7 der EN 60745.

18

DE

SM 1212CES Plus ● SMА 1212CES Plus

Allgemeine

Sicherheitshinweise

für Elektrowerkzeuge

WARNUNG: Lesen Sie alle Sicher-

heitshinweise und Anweisungen. Versäum-

nisse bei der Einhaltung der Sicherheitshin-

weise und Anweisungen können elektrischen

Schlag, Brand und/oder schwere Verletzun-

gen verursachen.

Bewahren Sie alle Sicherheitshinweise

und Anweisungen für die Zukunft auf.

Der in den Sicherheitshinweisen verwende-

te Begriff „Elektrowerkzeug“ bezieht sich auf

netzbetriebene Elektrowerkzeuge (mit Netzka-

bel) und auf akkubetriebene Elektrowerkzeuge

(ohne Netzkabel).

1) Arbeitsplatzsicherheit

a) Halten Sie Ihren Arbeitsbereich sauber

und gut beleuchtet. Unordnung oder un-

beleuchtete Arbeitsbereiche können zu Un-

fällen führen.

b) Arbeiten Sie mit dem Elektrowerkzeug

nicht in explosionsgefährdeter Umge-

bung, in der sich brennbare Flüssigkei-

ten, Gase oder Stäube benden. Elek-

trowerkzeuge erzeugen Funken, die den

Staub oder die Dämpfe entzünden können.

c) Halten Sie Kinder und andere Personen

während der Benutzung des Elektro-

werkzeugs fern. Bei Ablenkung können

Sie die Kontrolle über das Gerät verlieren.

2) Elektrische Sicherheit

a) Der Anschlussstecker des Elektro werk-

zeuges muss in die Steckdose passen.

Der Stecker darf in keiner Weise ver-

ändert werden. Verwenden Sie keine

Adapterstecker gemeinsam mit schutz-

geerdeten Elektrowerkzeugen. Unverän-

derte Stecker und passende Steckdosen

verringern das Risiko eines elektrischen

Schlages.

b) Vermeiden Sie Körperkontakt mit geer-

deten Oberächen wie von Rohren, Hei-

zungen, Herden und Kühlschränken. Es

besteht ein erhöhtes Risiko durch elektri-

schen Schlag, wenn Ihr Körper geerdet ist.

c) Halten Sie Elektrowerkzeuge von Re-

gen oder Nässe fern. Das Eindringen von

Wasser in ein Elektrowerkzeug erhöht das

Risiko eines elektrischen Schlages.

d) Zweckentfremden Sie das Kabel nicht,

um das Elektrowerkzeug zu tragen, auf-

zuhängen oder um den Stecker aus der

Steckdose zu ziehen. Halten Sie das Ka-

bel fern von Hitze, Öl, scharfen Kanten

oder sich bewegenden Geräteteilen. Be-

schädigte oder verwickelte Kabel erhöhen

das Risiko eines elektrischen Schlages.

e) Wenn Sie mit einem Elektrowerkzeug

im Freien arbeiten, verwenden Sie nur

Verlängerungskabel, die auch für den

Außenbereich geeignet sind. Die Anwen-

dung eines für den Außenbereich geeig-

neten Verlängerungskabels verringert das

Risiko eines elektrischen Schlages.

f) Wenn der Betrieb des Elektrowerkzeu-

ges in feuchter Umgebung nicht ver-

meidbar ist, verwenden Sie einen Feh-

lerstromschutzschalter. Der Einsatz eines

Fehlerstromschutzschalters vermindert das

Risiko eines elektrischen Schlages.

3) Sicherheit von Personen

a) Seien Sie aufmerksam, achten Sie da-

rauf, was Sie tun, und gehen Sie mit

Vernunft an die Arbeit mit einem Elekt-

rowerkzeug. Benutzen Sie kein Elektro-

werkzeug, wenn Sie müde sind oder

unter dem Einuss von Drogen, Alkohol

oder Medikamenten stehen. Ein Moment

der Unachtsamkeit beim Gebrauch des

Elektrowerkzeuges kann zu ernsthaften

Verletzungen führen.

b) Tragen Sie persönliche Schutzausrüs-

tung und immer eine Schutz brille. Das

Tragen persönlicher Schutzausrüstung, wie

Staubmaske, rutschfeste Sicherheitsschu-

he, Schutzhelm oder Gehörschutz, je nach

Art und Einsatz des Elektrowerkzeuges,

verringert das Risiko von Verletzungen.

c) Vermeiden Sie eine unbeabsichtigte In-

betriebnahme. Vergewissern Sie sich,

dass das Elektrowerkzeug ausgeschal-

tet ist, bevor Sie es an die Stromversor-

gung und/oder den Akku anschließen,

es aufnehmen oder tragen. Wenn Sie

beim Tragen des Elektrowerkzeuges den

Finger am Schalter haben oder das Gerät

eingeschaltet an die Stromversorgung an-

schließen, kann dies zu Unfällen führen.

d) Entfernen Sie Einstellwerkzeuge oder

Schraubenschlüssel, bevor Sie das

Elektrowerkzeug einschalten. Ein Werk-

zeug oder Schlüssel, der sich in einem dre-

henden Geräteteil bendet, kann zu Verlet-

zungen führen.

e) Vermeiden Sie eine abnormale Körper-

La pagina sta caricando ...

Sparky SMA 1212CES Plus Manuale utente

Questo manuale è adatto anche per

Sparky SMA 1212CES Plus Manuale utente

in altre lingue

Documenti correlati

Altri documenti