Indesit WIDXXL 126 (EU).C Guida utente

Marca: Indesit

Modello: WIDXXL 126 (EU).C

Categoria: Lavatrici

Tipo: Guida utente

English,1

Contents

Installation, 2-3

Unpacking and levelling

Electric and water connections

The first wash cycle

Technical details

Washer-dryer description, 4-5

Control panel

Leds

Starting and Programmes, 6

Briefly: how to start a programme

Programme table

Personalisations, 7

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 8

Detergent dispenser

Preparing your laundry

Special items

Precautions and advice, 9

General safety

Disposal

Saving energy and respecting the environment

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning your appliance

Cleaning the detergent dispenser

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

Before calling for Assistance

WASHER-DRYER

WIDXXL 126

Instructions for use

Italiano,25

Espanol,13

ÅËËÇÍÉÊÁ,37

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the Washer-dryer to inform the

new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the Washer-dryer.

2. Check whether the Washer-dryer has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the four

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

Washer-dryer needs to be moved to another location.

 Packaging materials are not children's toys.

Levelling

1. Install the Washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the Washer-

dryer.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth (see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the Washer-dryer,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the

hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

 Never use hoses that have already been used.

Installation

Technical details

Model

WIDXXL 126

Dimensions

59.5 cm wide

85 cm high

53.5 cm deep

Capacity

from 1 to 7 kg for the wash programme;

from 1 to 5 kg for the drying programme

Electric

connections

please refer to the technical data plate

fixed to the machine

Wate r

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rpm

Control

programmes

according to

EN 50229

directive

Wash: programme 2; temperature 60°C;

run with a load of 7 kg.

Drying: first drying cycle performed with

a 2 kg load and the DRYING knob on

the setting;

Second drying cycle performed with a 5

kg load and the DRYING knob on the

setting.

This appliance is compliant with the

following European Community

Directives:

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96/CE

- 2006/95/CE (Low Voltage)

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (on the right);

 the supply voltage is included within the values i

ndicated on the Technical details table

(on the right);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

65 - 100 cm

Washer-dryer description

Control panel

Detergent dispenser

ON-OFF

Button

START/RESET

Button

TEMPERATURE

Knob

PROGRAMME

Knob

Leds

FUNCTION

Buttons

ON-OFF/

DOOR

LOCK

Led

Detergent dispenser: to add detergent and fabric

softener (see page 8).

LEDS: to find out which wash cycle phase is under

way.

If the Delay Timer function has been set, the time

left until the programme starts will be indicated (see

page 5).

DRYING knob: to set the desired drying cycle

(see page 7).

FUNCTION buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

TEMPERATURE knob: to set the temperature or

the cold wash cycle (see page 7).

START/RESET button: to start the programmes or

cancel any incorrect settings.

ON-OFF/DOOR LOCK Led: to find out whether the

Washer-dryer is on and if the appliance door can be

opened (see page 5).

ON/OFF button: to turn the Washer-dryer on and off.

PROGRAMME knob: to select the wash

programmes. The knob stays still during the cycle.

DRYING

Knob

Note: to avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner

by continuously rotating the drum at a speed which is slightly faster than the normal washing speed.

When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than

the set frequency.

If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.

The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.

ON-OFF/DOOR LOCK led

If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any

damages, wait for the LED to flash before you open the appliance door.

 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED

indicates there is an abnormality (see page 11).

Cycle phase under way:

During the wash cycle, the LEDs gradually illumina-

te on to indicate the cycle phase under way:

Prewash / Wash

Rinse

Spin cycle

Drying

Note:

- during draining, the LED corresponding to the

Spin cycle phase will be turned on.

- when the drying cycle is complete, the indicator

light relative to phase

will flash, to indicate that

the DRYING knob needs to be set back to the 0

setting.

Function buttons

The FUNCTION BUTTONS also act like LEDS.

When a function is selected, the corresponding

button is illuminated.

If the function selected is incompatible with the

programme set, the button will flash and the

function will not be enabled.

If you set a function that is incompatible with

another function you selected previously, only the

last one selected will be enabled.

Leds

The LEDS provide important information.

This is what they can tell you:

Delay set:

If the Delay Timer function has been enabled (see

page. 7), once you have started the programme,

the LED corresponding to the delay set will begin to

flash:

As time passes, the remaining delay will be

displayed, and the corresponding LED will flash:

Once the set delay is complete, the flashing LED will

turn off and the programme set will start.

Starting and Programmes

Programme table

Briefly: starting a programme

1. Switch the Washer-dryer on by pressing button .

All the LEDS will light up for a few seconds and

the ON-OFF/DOOR LOCK Led will begin to flash.

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the PROGRAMME knob to the programme

required.

4. Set the wash temperature (see page 7).

5. Set the drying cycle if necessary (see page 7).

6. Add the detergent and any fabric softener (see page 8).

7. Start he programme by pressing the START/RESET

button.

To cancel it, keep the START/RESET button pressed

for at least 2 seconds.

8. When the programme is finished, the ON-OFF/

DOOR LOCK Led will flash to indicate that the

appliance door can be opened. Take out your

laundry and leave the appliance door ajar to allow

the drum to dry thoroughly. Turn the Washer-dryer

off by pressing button

Notes

-For programme 9, we advise against exceeding a wash load of 3.5 kg.

-For programme 13 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts

30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

Type of fabric and

degree of soil

Prog. Temp.

Drying

Cycle

Detergent

Fabric

softener

Cycle

length

(minutes)

Description of wash cycle

pre-wash wash

Standard

Cotton:

Extremely soiled whites (sheets,

tablecloths, etc.)

90°C    

170

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Extremely soiled whites (sheets,

tablecloths, etc.)

90°C   

155

Wash cycle, rinse cycles, intermediate

and final spin cycles

Cotton:

Heavily soiled whites and fast

colours

60°C   

153

Wash cycle, rinse cycles, intermediate

and final spin cycles

Cotton:

Heavily soiled whites and delicate

colours

40°C   

115

Wash cycle, rinse cycles, intermediate

and final spin cycles

Cotton:

Slightly soiled whites and delicate

colours (shirts, jumpers, etc.)

40°C   

Wash cycle, rinse cycles, intermediate

and final spin cycles

Synthetics:

Heavily soiled fast colours

(baby linen, etc.)

0°C



Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Synthetics:

Heavily soiled fast colours

(baby linen, etc.)

40°C   

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Wool

40°C  

Wash cycle, rinse cycles, delicate

spin cycle

Very delicate fabrics (curtains, silk,

viscose, etc.)

30°C  

Wash cycle, rinse cycles, anti-

crease or draining cycle

Drying cotton



Drying delicates



Time 4 you

Cotton:

Heavily soiled whites and fast

colours

60°C  

Wash cycle, rinse cycles, intermediate

and final spin cycles

Synthetics:

Delicate colours (all types of

slightly soiled garments)

°C



Wash cycle, rinse cycles, delicate

spin cycle

Synthetics:

Delicate colours (all types of

slightly soiled garments)

30°C    30

Wash cycle, rinse cycles and

delicate spin cycle

Sport

Sports shoes

(MAX. 2 pairs)

°C

 50

Cold wash (without detergents),

wash cycle, rinse cycles, and delicate

spin cycle

Fabrics for sportswear

(Tracksuits, shorts, etc.)

30°C   60

Wash cycle, rinse cycles, intermediate

and final spin cycles

PARTIAL PROGRAMMES

Rinse   Rinse cycles and spin cycle

Spin cycle  Draining and spin cycle

Drain Drain

Personalisations

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).

The temperature can be lowered, or even set to a cold wash (

Set the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: From 40 minutes to 180.

B - Based on the damp level of the dry clothes:

Iron

: slightly damp clothes, easy to iron.

Hanger

: dry clothes to put away.

Cupboard

: very dry clothes, recommended for towelling

and bathrobes.

A cooling stage is foreseen at the end of the drying cycle.

If your laundry load to wash and dry is exceptionally in excess

of the maximum load foreseen (see table opposite), perform

the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the

drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.

Dry only

Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the

desired drying type using the DRYING knob.

Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of

dryness (Cupboard

, Hanger , Iron ).

- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

Fabric

type

Load type Max.

load

(kg) Cup-

board

Hanger Iron

Cotton,

Linen

Clothing of different sizes

5 180 170 140

Cotton Terry towels

5 180 170 140

Terit al,

Cotton

Sheets, Shirts

3 140 120 100

Acrylics Pyjamas, socks, etc.

170 6560

Nylon Slips, tights, stockings, etc.

170 6560

Table of drying times

The data contained in the

table are purely indicative.

Function Effect Comments

Enabled with

programmes:

Delay

Timer

Delays the start

of the wash by

up to 9 hours.

Press the button repeatedly until the LED corresponding to the

desired delay is turned on.

The fifth time the button is pressed, the function will be disabled.

N.B.: Once you have pressed the Start/Reset button, the delay

can only be decreased if you wish to modify it.

All

Easy iron

This option

reduces the

amount of

creasing on

fabrics, making

them easier to

iron.

When this function is set, programmes 4, 6 will end with the

laundry left to soak (Anti-crease) and the Rinse cycle phase

LED will flash.

- to conclude the cycle, press the START/RESET button;

- to run the draining cycle alone, set the knob to the relative

symbol and press the START/RESET button.

This function is incompatible with the STAIN REMOVAL function.

If you also want to run the drying cycle, this button is enabled

only if combined with level (Ir on ).

3, 4, 6,

9, 10,

Rinse cycle.

Extra

Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 9,

10, 12, 13,

Rinse cycle.

1200-600

Reduces the

spin speed.

All

programmes

except for 6, 7,

8 and draining.

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

 Do not use hand wash detergent because it may

form too much foam.

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 7 kg

Synthetic fabrics: max 3 kg

Delicate fabrics: max 2 kg

Wool: max 1,5 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 6

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Wool: for best results, use a specific detergent,

taking care not to exceed a load of 1,5 kg.

Detergents and laundry

Precautions and advice

 The Washer-dryer was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

 This washer-dryer can only be used to dry clothes

which have been pre-washed in water.

Disposal

 Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your washing machine only needs less

than half the amount of water to get the best results:

an objective reached to respect the environment.

Saving on detergent, water, energy and time

 To avoid wasting resources, the Washer-dryer

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

 The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

 Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures. A

programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

The Delay Timer option (see page 7) helps to

organise your wash cycles accordingly.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning pump

that does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into

the pre-chamber that protects the pump, situated in

the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

Washer-dryer (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Troubleshooting

Your Washer-dryer could fail to work. Before calling for Assistance (see page 12), make sure the problem can't

easily be solved by consulting the following list.

Problem

The washer-dryer won't start.

The wash cycle won't start.

The washer-dryer fails to load

water.

The washer-dryer continuously

loads and unloads water.

The washer-dryer does not

drain or spin.

The washer-dryer vibrates too

much during the spin cycle.

The washer-dryer leaks.

The ON-OFF/DOOR LOCK Led

flashes rapidly at the same

time as at least one other LED.

There is too much foam.

The washer-dryer does not dry.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to

make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The

button has not been pressed.

 The START/RESET button has not been pressed.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Timer, see page 7).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 3).

 The free end of the hose is underwater (see page 3).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

Washer-dryer to load and unload water continuously. In order to avoid such

an inconvenience, special anti-drain trap valves are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 6).

 The Easy iron option is enabled: to complete the programme, press

the START/RESET button (see page 7).

 The drain hose is bent (see page 3).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 2).

 The Washer-dryer is not level (see page 2).

 The Washer-dryer is closed in between furniture cabinets and

the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 10).

 The drain hose is not secured properly (see page 3).

 Switch off the machine and unplug the appliance; wait for

approximately 1 minute then switch it on again.

If the problem persists, contact Assistance.

 The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

 You used too much detergent.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set (using the Delay Timer, see page 7).

 the DRYING knob is on the 0 setting.

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 11);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised servicemen.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washer-dryer.

Service

Espanol

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Descripción de la lavasecadora, 16-17

Panel de control

Luces testigo

Puesta en marcha y Programas, 18

En la práctica: poner en marcha un programa

Tabla de programas

Personalizaciones, 19

Seleccione la temperatura

Seleccione el secado

Funciones

Detergentes y ropa, 20

Cajón de detergentes

Preparar la ropa

Prendas especiales

Precauciones y consejos, 21

Seguridad general

Eliminaciones

Ahorrar y respetar el ambiente

Mantenimiento y cuidados, 22

Excluir el agua y la corriente eléctrica

Limpiar la lavasecadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Anomalías y soluciones, 23

Asistencia, 24

Antes de llamar a la Asistencia Técnica

LAVASECADORA

WIDXXL 126

Instrucciones para el uso

 Es importante conservar este manual para poder

consultarlo en cualquier momento. En caso de venta,

de cesión o de traslado, verifique que permanezca

junto con la lavasecadora para informar al nuevo

propietario sobre el funcionamiento y brindar las

correspondientes advertencias.

 Lea atentamente las instrucciones: ellas contienen

importante información sobre la instalación, el uso y la

seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavasecadora.

2. Controle que la lavasecadora no haya sufrido

daños durante el transporte. Si estuviera dañada no

la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para el

transporte y la arandela

de goma con el corres-

pondiente distanciador,

ubicados en la parte

posterior (ver la figura).

4. Cierre los orificios con los tapones de plástico

suministrados con el aparato.

5. Conserve todas las piezas: cuando la lavasecadora deba

ser transportada nuevamente, deberán volver a colocarse.

 Los embalajes no son juguetes para los niños.

Nivelación

1. Instale la lavasecadora sobre un piso plano y rígido, sin

apoyarla en las paredes, muebles ni en ningún otro aparato.

2. Si el piso no está

perfectamente horizontal,

compense las irregulari-

dades desenroscando o

enroscando los pies

delanteros (véase la

figura); el ángulo de

inclinación medido sobre

la superficie de trabajo,

no debe superar los 2º.

Una cuidadosa nivelación brinda estabilidad a la

máquina y evita vibraciones, ruidos y desplazamien-

tos durante el funcionamiento. Cuando se instala

sobre moquetas o alfombras, regule los pies para

conservar debajo de la lavasecadora un espacio

suficiente para la ventilación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de agua

1. Introduzca la junta A

en el extremo del tubo

de alimentación y

enrósquelo a un grifo de

agua fría con boca

roscada de 3/4 gas

(véase la figura).

Antes de conectarlo,

haga correr el agua

hasta que salga limpia.

2. Conecte el tubo de

alimentación a la

lavasecadora enroscán-

dolo en la toma de agua

correspondiente ubica-

da en la parte posterior

arriba y a la derecha

(véase la figura).

3. Verifique que el tubo no tenga pliegues ni estran-

gulaciones.

 La presión de agua del grifo debe estar comprendi-

da dentro de los valores contenidos en la tabla de

Datos técnicos (ver la página del costado).

 Si la longitud del tubo de alimentación no fuera

suficiente, diríjase a una tienda especializada o a un

técnico autorizado.

 No utilice nunca tubos ya usados.

Instalación

Conexión del tubo de descarga

Conecte el tubo de

descarga, sin plegarlo, a

un desagüe de pared

ubicado a una distancia

del piso comprendida

entre 65 y 100 cm;

o apóyelo al borde de

un lavabo o de una

bañera, uniendo la guía

suministrada con el

aparato, al grifo (véase

la figura). El extremo

libre del tubo de des-

carga no debe perma-

necer sumergido en el

agua.

 No se aconseja utilizar tubos de prolongación, de

todos modos, si es indispensable, la prolongación

debe tener el mismo diámetro del tubo original y no

superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

 la toma tenga la conexión a tierra y haya sido

hecha según las normas legales;

 la toma sea capaz de soportar la carga máxima

de potencia de la máquina indicada en la tabla de

Datos técnicos (ver al costado);

 la tensión de alimentación esté comprendida

dentro de los valores indicados en la tabla de

Datos técnicos (ver al costado);

 la toma sea compatible con el enchufe de la

lavadora. Si no es así, sustituya la toma o el

enchufe.

 La lavadora no debe ser instalada al aire libre, ni

siquiera si el lugar está preparado, ya que es muy

peligroso dejarla expuesta a la lluvia o a las tormentas.

 Una vez instalada la lavadora, la toma de corriente

debe ser fácilmente accesible.

 No utilice alargadores ni conexiones múltiples.

 El cable no debe estar plegado ni sufrir compresiones.

 El cable de alimentación debe ser sustituido sólo

por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas no

sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso, realice un

ciclo de lavado con detergente y sin ropa, seleccio-

nando el programa a 90ºC sin prelavado.

65 - 100 cm

Datos técnicos

Modelo

WIDXXL 126

Dimensiones

ancho 59,5 cm.

altura 85 cm.

profundidad 53,5 cm.

Capacidad

de 1 a 7 kg para el lavado;

de 1 a 5 kg para el secado.

Conexiones

eléctricas

ver la placa de características

técnicas aplicada en la máquina

Conexiones

hídricas

presión máxima 1 MPa (10 bar)

presión mínima 0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad de

centrifugado

máxima 1200 r.p.m.

Programas de

control según la

norma EN 50229

lavado: programa 2; temperatura

60ºC; efectuado con 7 kg. de carga.

secado: primer secado realizado

con 2 kg de cargay el mando de

SECADO en la posición ;

segundo secado realizado con 5 kg

de carga y el mando de SECADO en

la posición .

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 89/336/CEE del 03/05/89

(Compatibilidad Electromagnética) y

sucesivas modificaciones

- 2002/96/CE

- 2006/95/CE (Baja Tensión)

Panel de control

Descripción de la lavasecadora

Cajón de detergentes

Botón de

ENCENDIDO/

APAGADO

Botón de

START/RESET

Cajón de detergentes: para cargar detergentes y

aditivos (véase la pág. 20).

Luces testigo: para seguir el estado de avance del

programa de lavado.

Si se seleccionó la función Delay Timer, indicarán el

tiempo que falta para la puesta en marcha del

programa (ver la pág. 17).

Mando de SECADO: para seleccionar el secado

deseado (ver la pág. 19).

Botones de FUNCIÓN: para seleccionar las funcio-

nes disponibles. El botón correspondiente a la

función seleccionada permanecerá encendido.

Mando de TEMPERATURA: para seleccionar la

temperatura o el lavado en frío (ver la pág. 19).

Botón de START/RESET: para poner en marcha

los programas o anular las selecciones incorrectas.

Luz indicadora de ENCENDIDO/PUERTA BLO-

QUEADA: para saber si la lavasecadora está encen-

dida y si la puerta se puede abrir (ver la pág. 17).

Botón de ENCENDIDO/APAGADO: para encender

y apagar la lavasecadora.

Mando de PROGRAMAS: para elegir los progra-

mas. Durante el programa el mando no se mueve.

Mando de

TEMPERATURA

Mando de

PROGRAMAS

Luces

testigo

Botones de

FUNCIÓN

Mando de

SECADO

Luz indicadora de

ENCENDIDO/PUERTA

BLOQUEADA

Notas: Para evitar vibraciones excesivas, antes de cada centrifugado, la máquina distribuye la carga de modo

uniforme, esto se produce efectuando rotaciones continuas del cesto a una velocidad ligeramente superior a la

del lavado.

Aún cuando después de repetidos intentos, la carga no se distribuye perfectamente, la máquina realiza el

centrifugado a una velocidad inferior a la prevista.

Cuando existe un excesivo desequilibrado, la máquina efectúa la distribución en lugar del centrifugado.

Los intentos de equilibrado pueden aumentar la duración total del ciclo hasta un máximo de 10 minutos.

Luz indicadora de ENCENDIDO/PUERTA BLOQUEADA

La luz testigo encendida indica que la puerta está bloqueada para impedir aperturas accidentales; para evitar

daños es necesario esperar que la luz testigo centellee antes de abrir la puerta.

 El centelleo rápido de la luz indicadora de ENCENDIDO/PUERTA BLOQUEADA simultáneamente con, al me-

nos, el de otra luz testigo, indica una anomalía (ver la pág. 23).

Fase en curso:

Durante el ciclo de lavado, las luces testigo se

encenderán progresivamente para indicar su

estado de avance.

Prelavado / Lavado

Aclarado

Centrifugado

Secado

Nota:

- durante la fase de descarga se iluminará la luz

testigo correspondiente a la fase de Centrifugado.

- al finalizar el ciclo de secado, la luz testigo co-

rrespondiente a la fase

centelleará para indicar

que es necesario llevar el mando de SECADO a la

posición 0.

Botones de FUNCIÓN

Los BOTONES DE FUNCIÓN también actúan

como luces testigo.

Al seleccionar una función, el botón correspondien-

te se iluminará.

Si la función seleccionada no es compatible con el

programa elegido, el botón centelleará y la función

no se activará.

Cuando se seleccione una función incompatible

con otra seleccionada precedentemente, perma-

necerá activa sólo la última selección realizada.

Luces testigo

Las luces testigo suministran información importante.

He aquí lo que nos dicen:

Retraso seleccionado:

Si fue activada la función Delay Timer (ver la pág.

19), después de haber puesto en marcha el progra-

ma, comenzará a centellear la luz testigo correspon-

diente al retraso fijado:

Con el transcurrir del tiempo se visualizará el retraso

residual y el centelleo de la luz testigo correspondiente:

Una vez transcurrido el tiempo de retraso fijado, la

luz testigo centelleante se apagará y comenzará el

programa seleccionado.

Tipos de tejidos y de suciedad Programas

Te m p e -

ratura

Secado

Detergente

Suavi-

zante

Duración

del ciclo

(m in utos)

Descripción del ciclo de lavado

prelav. lavado

Estándar

lgodón

Blancos sumamente

sucios (sábanas, manteles, etc.)

90°C    

170

Prelavado, lavado, aclarados,

centrífugas intermedias y final

lgodón

Blancos sumamente

sucios (sábanas, manteles, etc.)

90°C   

155

Lavado, aclarados, centrífugas

intermedias y final

lgodón

Blancos y coloreados

resistentes muy sucios

60°C   

153

Lavado, aclarados, centrífugas

intermedias y final

lgodón

Blancos y coloreados

delicados muy sucios

40°C   

115

Lavado, aclarados, centrífugas

intermedias y final

lgodón

Blancos poco sucios y

colores delicados

(camisas, camisetas, etc.)

40°C   

Lavado, aclarados, centrífugas

intermedias y final

Sintéticos:

Colores resistentes

muy sucios (ropa para recién

nacidos, etc.)

60°C   

Lavado, aclarados, antiarrugas o

centrífuga delicada

Sintéticos:

Colores resistentes

muy sucios (ropa para recién

nacidos, etc.)

40°C   

Lavado, aclarados, antiarrugas o

centrífuga delicada

Lana

40°C  

Lavado, aclarados y

centrifugación delicada

Tejidos muy delicados

(cortinas, seda, viscosa, etc.)

30°C  

Lavado, aclarados, antiarrugas o

desague

Secado para telas de algodón



Secado para tejidos delicados



Tim e 4 you

lgodón

Blancos y coloreados

resistentes muy sucios

60°C  

Lavado, aclarados, centrífugas

intermedias y final

Sintéticos:

Colores delicados (ropa

de todo tipo ligeramente sucia)

°C



Lavado, aclarados y centrífuga

delicada

Sintéticos:

Colores delicados (ropa

de todo tipo ligeramente sucia)

30°C    30

Lavado, aclarados y centrífuga

delicada

Sport

Calzado deportivo

(

MAX. 2 pares.

)

°C

 50

Lavado en frío (sin detergente),

lavado, aclarados y centrifugación

delicada

Tejidos para ropa deportiva

(chandal, pantalón corto, etc.)

30°C   60

Lavado, aclarados, centrífugas

intermedias y final

PROGRAMAS PARCIALES

Aclarado   Aclarados y centrifugación

Centrifugación  Desague y centrifugación

Desague Desague

Puesta en marcha y Programas

Tabla de programas

En la práctica: poner en marcha un

programa

1. Encienda la lavasecadora pulsando el botón .

Todas las luces testigo se encenderán durante

algunos segundos, luego se apagarán y la luz

indicadora de ENCENDIDO/PUERTA BLOQUEADA

comenzará a centellear.

2. Cargue la ropa y cierre la puerta.

3. Seleccione el programa deseado con el mando de

PROGRAMAS.

4. Fije la temperatura de lavado (ver la pág. 19).

5. Seleccione el secado si es necesario (ver la pág. 19).

6. Vierta el detergente y los aditivos (véase la pág. 20).

7. Ponga en marcha el programa pulsando el botón

START/RESET.

Para anular, mantenga presionado el botón

START/RESET durante 2 segundos como mínimo.

8. Al finalizar el programa, la luz indicadora de ENCEN-

DIDO/PUERTA BLOQUEADA centelleará indicando

que la puerta se puede abrir. Extraiga la ropa y deje la

puerta semicerrada para permitir que el cesto se

seque. Apague la lavasecadora pulsando el botón

Notas

-En el programa 9 es aconsejable no superar una carga de ropa de 3,5 kg.

-En el programa 13 se aconseja no superar una carga de ropa de 2 kg.

-Para la descripción del antiarrugas: consulte Plancha fácil, página siguiente. Los datos contenidos en la tabla

tienen un valor indicativo.

Programa especial

Diario 30' (programa 11 para Sintéticos) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo:

dura sólo 30 minutos y de esa manera hace ahorrar energía y tiempo. Seleccionando el programa (11 a 30ºC)

es posible lavar conjuntamente tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 3 kg.

Se aconseja el uso de detergente líquido.

Personalizaciones

Seleccione la temperatura

Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas en la pág. 18).

La temperatura se puede disminuir hasta el lavado en frío (

Seleccione el secado

Girando el mando de SECADO se selecciona el tipo de

secado deseado. Se han previsto dos posibilidades:

A - En base al tiempo: De 40 a 180 minutos.

B - En base al nivel de humedad de las prendas secadas:

Planchado

: prendas ligera-mente húmedas, fáciles de

planchar.

Seque y cuelgue

: prendas secas, listas para guardar.

Ropero

: prendas muy secas, aconsejado para toallas y

batas.

Al finalizar el secado continúa un período de enfriamiento.

Si excepcionalmente la carga de ropa para lavar y secar es

superior al máximo previsto (ver la tabla ubicada al costado), realice el lavado, y una vez finalizado el programa,

divida la carga y vuelva a colocar una parte en el cesto. A partir de ese momento, siga las instrucciones para

efectuar sólo el secado. Repita las mismas operaciones para la carga restante.

Sólo secado

Gire el mando de PROGRAMAS hasta una de las posiciones de secado (7-8) de acuerdo al tipo de tejido, luego

seleccione el tipo de secado deseado con el mando de SECADO.

Importante: - Durante el secado se efectuará un centrifugado si Ud. ha seleccionado uno de los programas

de algodón y uno de los niveles de secado (Ropero

, Seque y cuelgue , Planchado ).

- Para cargas de telas de algodón inferiores a 1 Kg, utilice el programa de secado correspondiente a los tejidos delicados.

Funciones

Las distintas funciones de lavado previstas por la lavasecadora permiten obtener la limpieza y el blanco desea-

dos. Para activar las funciones:

1. pulse el botón correspondiente a la función deseada de acuerdo con la tabla que se encuentra debajo;

2. el encendido del botón correspondiente indica que la función está activa.

Nota: El centelleo rápido del botón indica que la función correspondiente no se puede seleccionar para el programa elegido.

Tipo de

tela

Tipo de carga Carga

máx.

(kg) Ropero Seque y

cuelgue

Planchado

Algodón,

Lino

Ropa de distintas

dimensiones

5 180 170 140

Algodón Toallas

5 180 170 140

Terilene,

Algodón

Sábanas, Camisas

3 140 120 100

Acrílicos Pijamas,

calcetines, etc.

170 65 60

Nylon Combinaciones,

medias, etc.

170 65 60

Tabla de tiempos de secado

Los datos contenidos en la

tabla tienen un valor indicativo.

Funciones Efecto Notas para el uso

Activa con

los

programas:

Delay timer

Retrasa la puesta

en marcha de la

máquina hasta 9

horas.

Pulse varias veces el botón hasta encender la luz testigo

correspondiente al retraso deseado.

La quinta vez que se presione el botón, la función se desactivará.

Nota: Una vez pulsado el botón Start/Reset, se puede modificar el

valor del retraso sólo disminuyéndolo.

To d o s

Plancha

fácil

Reduce las

arrugas en los

tejidos,

facilitando el

planchado.

Seleccionando esta función, los programas 4, 6 se interrumpirán

con la ropa en remojo (Antiarrugas) y la luz indicadora de la fase

de Aclarado centelleará:

- para completar el ciclo pulse el botón START/RESET;

- para efectuar sólo la descarga coloque la perilla en el símbolo

correspondiente y pulse el botón START/RESET.

Si desea realizar también el secado, este botón funciona sólo

conjuntamente con el nivel (Planchado).

3, 4, 6,

9, 10,

Aclarado.

Aclarado

Extra

Aumenta la

eficacia del

aclarado.

Es aconsejable con la lavadora a plena carga o con dosis elevadas

de detergente.

1, 2, 3, 4, 9,

10, 12, 13

Aclarado.

1200-600

Disminuye la

velocidad de

centrifugado.

To d o s

excepto el

6, 7, 8 y la

descarga.

Cajón de detergentes

El buen resultado del lavado depende también de la

correcta dosificación del detergente: si se excede la

cantidad, no se lava de manera más eficaz, sino que

se contribuye a encostrar las partes internas de la

lavasecadora y a contaminar el ambiente.

Extraiga el cajón de

detergentes e introduz-

ca el detergente o el

aditivo de la siguiente

manera:

cubeta 1: Detergente para prelavado (en polvo)

cubeta 2: Detergente para lavado

(en polvo o líquido)

El detergente líquido se debe verter sólo antes de la

puesta en marcha.

cubeta 3: Aditivos (suavizante, etc.)

El suavizante no se debe volcar fuera de la rejilla.

 No use detergentes para el lavado a mano ya que

producen demasiada espuma.

Preparar la ropa

 Subdivida la ropa según:

- el tipo de tejido / el símbolo en la etiqueta.

- los colores: separe las prendas de color y las blancas.

 Vacíe los bolsillos y controle los botones.

 No supere los valores indicados, referidos al peso

de la ropa seca:

Tejidos resistentes: max 7 kg.

Tejidos sintéticos: max 3 kg.

Tejidos delicados: max 2 kg.

Lana: max 1,5 kg.

¿Cuánto pesa la ropa?

1 sábana 400/500 g

1 funda 150/200 g

1 mantel 400/500 g

1 albornoz 900/1.200 g

1 toalla 150/250 g

Prendas especiales

Cortinas: pliéguelas y colóquelas dentro de una

funda o de una bolsa de red. Lávelas solas sin

superar la media carga. Utilice el programa 6 que

excluye automáticamente el centrifugado.

Cazadoras acolchadas con plumas y

anoraks: si el relleno es de pluma de ganso o de

pato, se pueden lavar en la lavasecadora. Poner las

prendas del revés y realizar una carga máxima de

2-3 kg. repitiendo el enjuague una o dos veces y

utilizando el centrifugado delicado.

Lana: para obtener los mejores resultados, utilice

un detergente específico y no supere 1,5 kg. de

carga.

Detergentes y ropa

La pagina sta caricando ...

Indesit WIDXXL 126 (EU).C Guida utente

Marca: Indesit

Modello: WIDXXL 126 (EU).C

Categoria: Lavatrici

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

English: Indesit WIDXXL 126 (EU).C User guide
español: Indesit WIDXXL 126 (EU).C Guía del usuario
português: Indesit WIDXXL 126 (EU).C Guia de usuario
slovenčina: Indesit WIDXXL 126 (EU).C Užívateľská príručka

Indesit WIDXXL 126 (EU).C Guida utente

Indesit WIDXXL 126 (EU).C Guida utente

in altre lingue

Documenti correlati

Altri documenti